Influence of needle design and irrigation depth in the presence of vapor lock: A computational fluid dynamics analysis in human oval roots with apical ramification

This paper aims to study the removal of a vapor lock located in the apical ramification of an oval distal root of a human mandibular molar, simulating different needles and irrigation depths with computational fluid dynamic. A geometric reconstruction of the micro-CT of the molar shaped up to a WaveOne Gold Medium instrument was used. A vapor lock located in the apical 2 mm was incorporated. Geometries with positive pressure needles (side-vented [SV], flat or front-vented [FV] and notched [N]) and the EndoVac microcannula (MiC) were created to run the simulations. Irrigation key parameters (flow pattern, irrigant velocity, apical pressure, wall shear stress) and vapor lock removal were compared among the different simulations. Each needle behaved differently that is, FV removed the vapor lock from one ramification and had the highest apical pressure and shear stress values; SV removed the vapor lock in the main root canal but not in the ramification and reached the lowest apical pressure from the positive pressure needles; N was not able to completely remove the vapor lock and showed low apical pressure and shear stress; MiC removed the vapor lock from one ramification, had negative apical pressure and the lowest maximum shear stress. The main conclusion is that none of the needles showed complete removal of vapor lock. MiC, N, and FV were able to partially remove the vapor lock from one out of the three ramifications. However, SV needle was the only simulation that showed high shear stress with low apical pressure.

Biomechanical Modelling for Tooth Survival Studies: Mechanical Properties, Loads and Boundary Conditions-A Narrative Review

Recent biomechanical studies have focused on studying the response of teeth before and after different treatments under functional and parafunctional loads. These studies often involve experimental and/or finite element analysis (FEA). Current loading and boundary conditions may not entirely represent the real condition of the tooth in clinical situations. The importance of homogenizing both sample characterization and boundary conditions definition for future dental biomechanical studies is highlighted. The mechanical properties of dental structural tissues are presented, along with the effect of functional and parafunctional loads and other environmental and biological parameters that may influence tooth survival. A range of values for Young's modulus, Poisson ratio, compressive strength, threshold stress intensity factor and fracture toughness are provided for enamel and dentin; as well as Young's modulus and Poisson ratio for the PDL, trabecular and cortical bone. Angles, loading magnitude and frequency are provided for functional and parafunctional loads. The environmental and physiological conditions (age, gender, tooth, humidity, etc.), that may influence tooth survival are also discussed. Oversimplifications of biomechanical models could end up in results that divert from the natural behavior of teeth. Experimental validation models with close-to-reality boundary conditions should be developed to compare the validity of simplified models.

Comparison of Upper Neck Loading in Young Adult and Elderly Volunteers During Low Speed Frontal Impacts

Cervical pain and injuries are a major health problem globally. Existing neck injury criteria are based on experimental studies that included sled tests performed with volunteers, post-mortem human surrogates and animals. However, none of these studies have addressed the differences between young adults and elderly volunteers to date. Thus, this work analyzed the estimated axial and shear forces, and the bending moment at the craniocervical junction of nine young volunteers (18–30 years old) and four elderly volunteers (>65 years old) in a low-speed frontal deceleration. Since the calculation of these loads required the use of the mass and moment of inertia of the volunteers' heads, this study proposed new methods to estimate the inertial properties of the head of the volunteers based on external measurements that reduced the error of previously published methods. The estimated mean peak axial force (Fz) was −164.38 ± 35.04 N in the young group and −170.62 ± 49.82 N in the elderly group. The average maximum shear force (Fx) was −224.42 ± 54.39 N and −232.41 ± 19.23 N in the young and elderly group, respectively. Last, the estimated peak bending moment (My) was 13.63 ± 1.09 Nm in the young group and 14.81 ± 1.36 Nm in the elderly group. The neck loads experienced by the elderly group were within the highest values in the present study. Nevertheless, for the group of volunteers included in this study, no substantial differences with age were observed.

CFD analysis on the effect of combining positive and negative pressure during the irrigation of artificial isthmuses

Fluid dynamics generated by irrigation needles have not been deeply analyzed in root canal irregularities such as apical ramifications or isthmus where the cleaning capacity of irrigants might be compromised and hence the treatment outcome. The goal of this study was to compare the key irrigation parameters (flow pattern, irrigant velocity, apical pressure, and shear stress) between two irrigation needles and the additional effect of aspiration cannulas through computational fluid dynamics. A 3D-model consisting of two canals linked by an isthmus was modeled. The abovementioned needles irrigated the primary canal, whereas an aspiration cannula was located inside the secondary canal. Both the geometry definition and spatial discretization were carried out with ANSYS 16.2, through which six different simulations were performed: lateral exit (LE) needle, frontal exit (FE) needle, LE and cannula in crown (LEC), FE and cannula in crown (FEC), LE and cannula in middle third (LEM), FE and cannula in middle third (FEM). FE and FEM showed that the irrigation flow only passes through the isthmus in the most apical section (maximum irrigant velocity / shear stress = 8.44 m/s / 1628.44 Pa and 8.63 m/s / 1185.69 Pa, respectively). However, the remaining simulations showed the irrigation flow passing through the isthmus twice, through the most apical section first and through the upper part of the isthmus later (maximum irrigant velocity / shear stress = 8.48 m/s / 1298.24 Pa (LE), 8.61 m/s / 1261.36 Pa (LEM), 8.61 m/s / 1355.24 Pa (LEC), 8.59 m/s / 1256.87 Pa (FEC)). Furthermore, the highest velocity values were detected when aspiration cannulas were added.