Silver nanostar films for surface-enhanced Raman spectroscopy (SERS) of the pesticide imidacloprid

Strategies for synthetic control of anisotropic metal nanostructures have grown in recent years in part due to their great potential for application as surface-enhanced Raman scattering (SERS) sensing substrates. It has been shown that SERS using silver substrates is a powerful tool for identification and qualification of trace chemical analysis on the basis of their unique molecular vibrations. In this work, we synthesized star-shaped silver nanostructures and fabricated SERS substrates to use the SERS enhancement of the Raman signal to detect neonicotinoid pesticides. These silver nanostar substrates were prepared by assembling the nanostar particles on a glass substrate surface using a self-assembly technique with various layers of silver nanostars film. The silver nanostar distribution on the solid substrate surface was found to have good reproducibility, reusability and were a stable SERS substrate giving SERS enhancements for pesticide detection at concentrations as low as 10⁻⁶ mg/ml. The distribution of these silver nanostars on the surface allowed excellent reproducibility of the detection with a low relative standard derivation (RSD) of SERS intensity of 8%. This work potentially builds a platform for an ultrasensitive detector where samples can be probed with little to no pre-processing and a range of pollutants can be detected at very low levels.

Rhenium anchored Ti3C2T x (MXene) nanosheets for electrocatalytic hydrogen production

Atomically thin Ti₃C₂T _x (MXene) nanosheets with rich termination groups, acting as active sites for effective functionalization, are used as an efficient solid support to host rhenium (Re) nanoparticles for the electrocatalytic hydrogen evolution reaction (HER). The newly designed electrocatalyst - Re nanoparticles anchored on Ti₃C₂T _x MXene nanosheets (Re@Ti₃C₂T _x ) - exhibited promising catalytic activity with a low overpotential of 298 mV to achieve a current density of 10 mV cm^-2, while displaying excellent stability. In comparison, the pristine Ti₃C₂T _x MXene requires higher overpotential of 584 mV to obtain the same current density. After being stored under ambient conditions for 30 days, Re@Ti₃C₂T _x retained 100% of its initial catalytic activity for the HER, while the pristine Ti₃C₂T _x retained only 74.8% of its initial value. According to our theoretical calculations using density functional theory, dual Re anchored MXene (Re@Ti₃C₂T _x ) exhibits a near-zero value of Gibbs free energy (ΔG _H* = -0.06 eV) for the HER, demonstrating that the presence of Re significantly enhances the electrocatalytic activity of MXene nanosheets. This work introduces a facile strategy to develop an effective electrocatalyst for electrocatalytic hydrogen production.

Energy Interplay in Materials: Unlocking Next-Generation Synchronous Multisource Energy Conversion with Layered 2D Crystals

Layered 2D crystals have unique properties and rich chemical and electronic diversity, with over 6000 2D crystals known and, in principle, millions of different stacked hybrid 2D crystals accessible. This diversity provides unique combinations of properties that can profoundly affect the future of energy conversion and harvesting devices. Notably, this includes catalysts, photovoltaics, superconductors, solar-fuel generators, and piezoelectric devices that will receive broad commercial uptake in the near future. However, the unique properties of layered 2D crystals are not limited to individual applications and they can achieve exceptional performance in multiple energy conversion applications synchronously. This synchronous multisource energy conversion (SMEC) has yet to be fully realized but offers a real game-changer in how devices will be produced and utilized in the future. This perspective highlights the energy interplay in materials and its impact on energy conversion, how SMEC devices can be realized, particularly through layered 2D crystals, and provides a vision of the future of effective environmental energy harvesting devices with layered 2D crystals.

Heterointerface optimization in a covalent organic framework-on-MXene for high-performance capacitive deionization of oxygenated saline water

Capacitive deionization (CDI) provides a promising option for affordable freshwater while simultaneously storing energy, but its large-scale application is usually limited owing to the poor performance of conventional materials in natural (oxygenated) saline water. Herein, we report heterointerface optimization in a covalent organic framework (COF)-on-MXene heterostructure achieving a high CDI performance for desalination of oxygenated saline water. The 2D heterostructure with the optimal core-shell architecture inherits the high conductivity and reversible ion intercalation/deintercalation ability of MXene, and the hierarchical porous structure, large porosity, and extraordinary redox capacity of COFs. Thanks to the heterointerface optimization, the MXene@COF heterostructure exhibits a very stable cycling performance over 100 CDI cycles with a maximum NaCl adsorption capacity of 53.1 mg g^-1 in oxygenated saline water, among the state-of-the-art values for CDI electrodes and also exceeding those of most MXene-based or 2D materials. This study highlights the importance of heterointerface optimization in MXene-organic 2D heterostructures to promote CDI of natural (oxygenated) saline water.

Plasma-Induced Nanocrystalline Domain Engineering and Surface Passivation in Mesoporous Chalcogenide Semiconductor Thin Films

The synthesis of highly crystalline mesoporous materials is key to realizing high‐performance chemical and biological sensors and optoelectronics. However, minimizing surface oxidation and enhancing the domain size without affecting the porous nanoarchitecture are daunting challenges. Herein, we report a hybrid technique that combines bottom‐up electrochemical growth with top‐down plasma treatment to produce mesoporous semiconductors with large crystalline domain sizes and excellent surface passivation. By passivating unsaturated bonds without incorporating any chemical or physical layers, these films show better stability and enhancement in the optoelectronic properties of mesoporous copper telluride (CuTe) with different pore diameters. These results provide exciting opportunities for the development of long‐term, stable, and high‐performance mesoporous semiconductor materials for future technologies.

A bright future for engineering piezoelectric 2D crystals

The piezoelectric effect, mechanical-to-electrical and electrical-to-mechanical energy conversion, is highly beneficial for functional and responsive electronic devices. To fully exploit this property, miniaturization of piezoelectric materials is the subject of intense research. Indeed, select atomically thin 2D materials strongly exhibit the piezoelectric effect. The family of 2D crystals consists of over 7000 chemically distinct members that can be further manipulated in terms of strain, functionalization, elemental substitution (i.e. Janus 2D crystals), and defect engineering to induce a piezoelectric response. Additionally, most 2D crystals can stack with other similar or dissimilar 2D crystals to form a much greater number of complex 2D heterostructures whose properties are quite different to those of the individual constituents. The unprecedented flexibility in tailoring 2D crystal properties, coupled with their minimal thickness, make these emerging highly attractive for advanced piezoelectric applications that include pressure sensing, piezocatalysis, piezotronics, and energy harvesting. This review summarizes literature on piezoelectricity, particularly out-of-plane piezoelectricity, in the vast family of 2D materials as well as their heterostructures. It also describes methods to induce, enhance, and control the piezoelectric properties. The volume of data and role of machine learning in predicting piezoelectricity is discussed in detail, and a prospective outlook on the 2D piezoelectric field is provided.

Highly Dispersed Ru Nanoparticles on Boron-Doped Ti3 C2 Tx (MXene) Nanosheets for Synergistic Enhancement of Electrocatalytic Hydrogen Evolution

2D-layered materials have attracted increasing attention as low-cost supports for developing active catalysts for the hydrogen evolution reaction (HER). In addition, atomically thin Ti₃ C₂ T_x (MXene) nanosheets have surface termination groups (T_x : F, O, and OH), which are active sites for effective functionalization. In this work, heteroatom (boron)-doped Ti₃ C₂ T_x (MXene) nanosheets are developed as an efficient solid support to host ultrasmall ruthenium (Ru) nanoparticles for electrocatalytic HER. The quantum-mechanical first-principles calculations and electrochemical tests reveal that the B-doping onto 2D MXene nanosheets can largely improve the intermediate H* adsorption kinetics and reduce the charge-transfer resistance toward the HER, leading to increased reactivity of active sites and favorable electrode kinetics. Importantly, the newly designed electrocatalyst based on Ru nanoparticles supported on B-doped MXene (Ru@B-Ti₃ C₂ T_x ) nanosheets shows a remarkable catalytic activity with low overpotentials of 62.9 and 276.9 mV to drive 10 and 100 mA cm^-2 , respectively, for the HER, while exhibiting excellent cycling stabilities. Moreover, according to the theoretical calculations, Ru@B-Ti₃ C₂ T_x exhibits a near-zero value of Gibbs free energy (ΔG_H*  = 0.002 eV) for the HER. This work introduces a facile strategy to functionalize MXene for use as a solid support for efficient electrocatalysts.

1D-2D Synergistic MXene-Nanotubes Hybrids for Efficient Perovskite Solar Cells

Incorporation of 2D MXenes into the electron transporting layer (ETL) of perovskite solar cells (PSCs) has been shown to deliver high-efficiency photovoltaic (PV) devices. However, the ambient fabrication of the ETLs leads to unavoidable deterioration in the electrical properties of MXene due to oxidation. Herein, sorted metallic single-walled carbon nanotubes (m-SWCNTs) are employed to prepare MXene/SWCNTs composites to improve the PV performance of PSCs. With the optimized composition, a power conversion efficiency of over 21% is achieved. The improved photoluminescence and reduced charge transfer resistance revealed by electrochemical impedance spectroscopy demonstrated low trap density and improved charge extraction and transport characteristics due to the improved conductivity originating from the presence of nanotubes as well as the reduced defects associated with oxygen vacancies on the surface of the SnO₂ . The MXene/SWCNTs strategy reported here provides a new avenue for realizing high-performance PSCs.

Interfacial piezoelectric polarization locking in printable Ti3C2Tx MXene-fluoropolymer composites

Piezoelectric fluoropolymers convert mechanical energy to electricity and are ideal for sustainably providing power to electronic devices. To convert mechanical energy, a net polarization must be induced in the fluoropolymer, which is currently achieved via an energy-intensive electrical poling process. Eliminating this process will enable the low-energy production of efficient energy harvesters. Here, by combining molecular dynamics simulations, piezoresponse force microscopy, and electrodynamic measurements, we reveal a hitherto unseen polarization locking phenomena of poly(vinylidene fluoride–co–trifluoroethylene) (PVDF-TrFE) perpendicular to the basal plane of two-dimensional (2D) Ti₃C₂T_x MXene nanosheets. This polarization locking, driven by strong electrostatic interactions enabled exceptional energy harvesting performance, with a measured piezoelectric charge coefficient, d₃₃, of −52.0 picocoulombs per newton, significantly higher than electrically poled PVDF-TrFE (approximately −38 picocoulombs per newton). This study provides a new fundamental and low-energy input mechanism of poling fluoropolymers, which enables new levels of performance in electromechanical technologies.

Fluoropolymers are state-of-the-art flexible piezoelectric materials, yet require massive energy inputs to function. Here, the authors show that the electrostatic field around a 2D material leads to polarization orientation and maximized piezoelectric performance, without external energy input.

Spatially isolated redox processes enabled by ambipolar charge transport in multi-walled carbon nanotube mats

This work demonstrates a simple dual-well device which enables spatially isolated solutions to undergo complementary redox reactions. The device functions by the ambipolar transport of charge carriers between two spatially isolated poly(dimethylsiloxane) (PDMS) microwells through an underlying multi-walled carbon nanotube (MWCNT) mat. This MWCNT mat enables charge carriers, produced from the decomposition of an analyte in one solution, to drive a redox reaction in a spatially isolated second colorimetric read-out solution via a potential difference between the wells. As proof-of-concept a visible colorimetric read-out was shown using an enzyme, cytochrome c (reduced in 16 h), and the visualizing reagent 3,3',5,5'-tetramethylbenzidine (TMB) (oxidized in 2.5 h) for the detection of dithionite and hydrogen peroxide, respectively, without any external energy input. We discuss the origin of this phenomenon and highlight the ability of MWCNTs to accept and transport both electrons and holes efficiently between spatially isolated solutions giving rise to a highly versatile sensor suitable for use in simple, low-cost point-of-care diagnostics.

Ambient Fabrication of Organic-Inorganic Hybrid Perovskite Solar Cells

Organic-inorganic hybrid perovskite solar cells (PSCs) have attracted significant attention in recent years due to their high-power conversion efficiency, simple fabrication, and low material cost. However, due to their high sensitivity to moisture and oxygen, high efficiency PSCs are mainly constructed in an inert environment. This has led to significant concerns associated with the long-term stability and manufacturing costs, which are some of the major limitations for the commercialization of this cutting-edge technology. Over the past few years, excellent progress in fabricating PSCs in ambient conditions has been made. These advancements have drawn considerable research interest in the photovoltaic community and shown great promise for the successful commercialization of efficient and stable PSCs. In this review, after providing an overview to the influence of an ambient fabrication environment on perovskite films, recent advances in fabricating efficient and stable PSCs in ambient conditions are discussed. Along with discussing the underlying challenges and limitations, the most appropriate strategies to fabricate efficient PSCs under ambient conditions are summarized along with multiple roadmaps to assist in the future development of this technology.

Efficiency and stability enhancement of perovskite solar cells using reduced graphene oxide derived from earth-abundant natural graphite

Graphene – two-dimensional (2D) sheets of carbon atoms linked in a honeycomb pattern – has unique properties that exhibit great promise for various applications including solar cells. Herein we prepared two-dimensional (2D) reduced graphene oxide (rGO) nanosheets from naturally abundant graphite flakes (obtained from Tuv aimag in Mongolia) using solution processed chemical oxidation and thermal reduction methods. As a proof of concept, we used our rGO as a hole transporting material (HTM) in perovskite solar cells (PSCs). Promisingly, the use of rGO in the hole transporting layer (HTL) not only enhanced the photovoltaic efficiency of PSCs, but also improved the device stability. In particular, the best performing PSC employing rGO nanosheets exhibited a power conversion efficiency (PCE) of up to 18.13%, while the control device without rGO delivered a maximum efficiency of 17.26%. The present work demonstrates the possibilities for solving PSC issues (stability) using nanomaterials derived from naturally abundant graphite sources.

Solution processed reduced graphene oxide nanosheets have been prepared from naturally abundant graphite flakes and used to enhance the efficiency and stability of perovskite solar cells.

Nanoscale Patterning of Carbon Nanotubes: Techniques, Applications, and Future

Carbon nanotube (CNT) devices and electronics are achieving maturity and directly competing or surpassing devices that use conventional materials. CNTs have demonstrated ballistic conduction, minimal scaling effects, high current capacity, low power requirements, and excellent optical/photonic properties; making them the ideal candidate for a new material to replace conventional materials in next-generation electronic and photonic systems. CNTs also demonstrate high stability and flexibility, allowing them to be used in flexible, printable, and/or biocompatible electronics. However, a major challenge to fully commercialize these devices is the scalable placement of CNTs into desired micro/nanopatterns and architectures to translate the superior properties of CNTs into macroscale devices. Precise and high throughput patterning becomes increasingly difficult at nanoscale resolution, but it is essential to fully realize the benefits of CNTs. The relatively long, high aspect ratio structures of CNTs must be preserved to maintain their functionalities, consequently making them more difficult to pattern than conventional materials like metals and polymers. This review comprehensively explores the recent development of innovative CNT patterning techniques with nanoscale lateral resolution. Each technique is critically analyzed and applications for the nanoscale-resolution approaches are demonstrated. Promising techniques and the challenges ahead for future devices and applications are discussed.

Matrix metalloproteinase-2-targeted superparamagnetic Fe3O4-PEG-G5-MMP2@Ce6 nanoprobes for dual-mode imaging and photodynamic therapy

This work explored the application of matrix metalloproteinase 2-targeted superparamagnetic nanoprobes for magnetic resonance imaging (MRI), near infrared (NIR) fluorescence imaging and photodynamic therapy of tumors. PEG, PAMAM (G5) and matrix metalloproteinase 2 (MMP2) were attached to the surface of carboxylated Fe3O4 nanoparticles (NPs) using a chemical coupling method and then finally loaded with the photosensitizer chlorin e6 (Ce6). In vitro and in vivo experiments demonstrated that the Fe3O4-PEG-G5-MMP2@Ce6 nanoprobes exhibited excellent stability, precise tumor targeting and biocompatibility. Furthermore, the fluorescence properties of Fe3O4-PEG-G5-MMP2@Ce6 nanoprobes were analogous to Ce6 and could be employed for fluorescence imaging. Meanwhile, the Fe3O4-PEG-G5-MMP2@Ce6 nanoprobes have also been shown to be effective as contrast agents for T2-weighted MRI. The target molecule MMP2 enhanced the tumor targeting ability of Fe3O4-PEG-G5-MMP2@Ce6 nanoprobes. Additionally, the Fe3O4-PEG-G5-MMP2@Ce6 nanoprobes significantly inhibited tumor growth compared with PBS and free Ce6. This work will inspire greater enthusiasm for the construction of multifunctional magnetic nanoplatforms for biomedical applications.

Electrically Sorted Single-Walled Carbon Nanotubes-Based Electron Transporting Layers for Perovskite Solar Cells

Incorporation of as prepared single-walled carbon nanotubes (SWCNTs) into the electron transporting layer (ETL) is an effective strategy to enhance the photovoltaic performance of perovskite solar cells (PSCs). However, the fundamental role of the SWCNT electrical types in the PSCs is not well understood. Herein, we prepared semiconducting (s-) and metallic (m-) SWCNT families and integrated them into TiO₂ photoelectrodes of the PSCs. Based on experimental and theoretical studies, we found that the electrical type of the nanotubes plays an important role in the devices. In particular, the mixture of s-SWCNTs and m-SWCNTs (2:1 w/w)-based PSCs exhibited a remarkable efficiency of up to 19.35%, which was significantly higher than that of the best control cell (17.04%). In this class of PSCs, semiconducting properties of s-SWCNTs play a critical role in extracting and transporting electrons, whereas m-SWCNTs provide high conductance throughout the electrode.

Enhancing Upconversion Luminescence Efficiency via Chiral β-NaYF4:Er3+/Yb3+ Microcrystals Based on Mesoscale Regulation

Chirality, universal characteristics of nature, introduces asymmetry in synthetic materials. Revealing the microscopic asymmetry of macroscopically symmetric materials is the key to control the growth of chiral materials and give full play to their application potential. Materials for photon upconversion (UC) are of great interest for many applications owing to their anti-Stoke luminescence process, especially for chiral UC materials. For the preparation of UC materials, a tiny change in reaction parameters will lead to variations in morphology, phase components, and fluorescence intensity, as well as its chirality. Because of the strict reaction conditions for the formation of chiral UC materials, there are no reports of the successful synthesis of chiral UC materials. Therefore, a facile method for the controllable synthesis of chiral UC materials is highly desired. Herein, chiral-assembled hexagonal prisms of β-NaYF₄:Er³⁺/Yb³⁺ microcrystals were synthesized to realize the smart manipulation of their morphology as well as a great improvement of the fluorescence efficiency. We proposed a three-stage doped β-NaYF₄ crystal growth mechanism on mesoscale regulation, where the fluorescence enhancement principle of chirality was revealed. The enhancement of fluorescence efficiency of chiral UC materials endows their promising application in luminescent displays.

Synthesis, purification, properties and characterization of sorted single-walled carbon nanotubes

Single-walled carbon nanotubes (SWCNTs) have attracted significant attention due to their outstanding mechanical, chemical and optoelectronic properties, which makes them promising candidates for use in a wide range of applications. However, as-produced SWCNTs have a wide distribution of various chiral species with different properties (i.e. electronic structures). In order to take full advantage of SWCNT properties, highly purified and well-separated SWCNTs are of great importance. Recent advances have focused on developing new strategies to effectively separate nanotubes into single-chirality and/or semiconducting/metallic species and integrating them into different applications. This review highlights recent progress in this cutting-edge research area alongside the enormous development of their identification and structural characterization techniques. A comprehensive review of advances in both controlled synthesis and post-synthesis separation methods of SWCNTs are presented. The relationship between the unique structure of SWCNTs and their intrinsic properties is also discussed. Finally, important future directions for the development of sorting and purification protocols for SWCNTs are provided.

Recent progress in magnetic nanoparticles: synthesis, properties, and applications

The rapid development of advanced nanotechnology has continuously changed many aspects of society. One important nanostructured material, magnetic nanoparticles (NPs), has applications in many areas including clean energy, biology and engineering because of their special magnetic properties. The synthesis of magnetic nanomaterials with desired sizes and morphology has attracted great attention. Nanomaterials with different properties can be combined to construct multifunctional nanoplatforms through systematic surface engineering. The surface modification of magnetic NPs presents the opportunity for them to be used in many practical applications. Functionalized magnetic NPs have been successfully applied in catalysis, as thermoelectric materials, for drug delivery, as imaging agents in nuclear magnetic resonance and in biosensors. In this review, synthetic methods for magnetic NPs and some of their important properties are described. Then the latest progress of the application of magnetic NPs in energy and biology has been summarized and discussed. Finally, we discuss some issues that still need to be solved and the prospects for magnetic NPs.

Direct-Patterning SWCNTs Using Dip Pen Nanolithography for SWCNT/Silicon Solar Cells

Dip pen nanolithography (DPN) is used to pattern single-walled carbon nanotube (SWCNT) lines between the n-type Si and SWCNT film in SWCNT/Si solar cells. The SWCNT ink composition, loading, and DPN pretreatment are optimized to improve patterning. This improved DPN technique is then used to successfully pattern >1 mm long SWCNT lines consistently. This is a 20-fold increase in the previously reported direct-patterning of SWCNT lines using the DPN technique, and demonstrates the scalability of the technique to pattern larger areas. The degree of the uniformity of SWCNTs in these lines is further characterized by Raman spectroscopy and scanning electron microscopy. The patterned SWCNT lines are used as thin conductive pathways in SWCNT/Si solar cells, similar to front contact electrodes. The critical parameters of these solar cells are measured and compared to control cells without SWCNT lines. The addition of SWCNT lines increases power conversion efficiency by 40% (relative). Importantly, the SWCNT lines reduce average series resistance by 44%, and consequently increase average fill factor by 24%.

Solution Based Methods for the Fabrication of Carbon Nanotube Modified Atomic Force Microscopy Probes

High aspect ratio carbon nanotubes are ideal candidates to improve the resolution and lifetime of atomic force microscopy (AFM) probes. Here, we present simple methods for the preparation of carbon nanotube modified AFM probes utilising solvent evaporation or dielectrophoresis. Scanning electron microscopy (SEM) of the modified probes shows that the carbon nanotubes attach to the probe apex as fibres and display a high aspect ratio. Many of the probes made in this manner were initially found to exhibit anomalous feedback characteristics during scanning, which rendered them unsuitable for imaging. However, we further developed and demonstrated a simple method to stabilise the carbon nanotube fibres by scanning with high force in tapping mode, which either shortens or straightens the carbon fibre, resulting in stable and high quality imaging AFM imaging.

Plasmonic Gold Nanostars Incorporated into High-Efficiency Perovskite Solar Cells

Incorporating appropriate plasmonic nanostructures into photovoltaic (PV) systems is of great utility for enhancing photon absorption and thus improving device performance. Herein, the successful integration of plasmonic gold nanostars (AuNSs) into mesoporous TiO₂ photoelectrodes for perovskite solar cells (PSCs) is reported. The PSCs fabricated with TiO₂ -AuNSs photoelectrodes exhibited a device efficiency of up to 17.72 %, whereas the control cells without AuNSs showed a maximum efficiency of 15.19 %. We attribute the origin of increased device performance to enhanced light absorption and suppressed charge recombination.

Large-scale immuno-magnetic cell sorting of T cells based on a self-designed high-throughput system for potential clinical application

In this contribution, we designed four types of immuno-magnetic nanoparticles for separation of different T cells (CD3⁺, CD4⁺, CD8⁺ and CD14⁺ T cells), and we established a new large-scale immuno-magnetic cell sorting procedure to achieve an enrichment of particular T cells using our designed auto-IMACS device. This device could achieve recyclable large-scale cell sorting, for which the throughput of the system reached ∼4000 mL and the maximum cell capacity was 4 × 10¹⁰. The collected cells were analyzed by flow cytometry and visual cytology data, and the effective selection rates of CD3⁺, CD4⁺, CD8⁺ and CD14⁺ T cells were 79.3%, 74.1%, 57.1% and 67.9%, respectively. The sorted CD8⁺ T cells still retained good cytotoxic activity against specific cells. In addition, the sorted T cells can also be further incubated in vitro and proliferated, and even could be infused back into patients for immunotherapy in the near future.

Fabrication of Tissue-Engineered Bionic Urethra Using Cell Sheet Technology and Labeling By Ultrasmall Superparamagnetic Iron Oxide for Full-Thickness Urethral Reconstruction

Urethral strictures remain a reconstructive challenge, due to less than satisfactory outcomes and high incidence of stricture recurrence. An “ideal” urethral reconstruction should establish similar architecture and function as the original urethral wall. We fabricated a novel tissue-engineered bionic urethras using cell sheet technology and report their viability in a canine model. Small amounts of oral and adipose tissues were harvested, and adipose-derived stem cells, oral mucosal epithelial cells, and oral mucosal fibroblasts were isolated and used to prepare cell sheets. The cell sheets were hierarchically tubularized to form 3-layer tissue-engineered urethras and labeled by ultrasmall super-paramagnetic iron oxide (USPIO). The constructed tissue-engineered urethras were transplanted subcutaneously for 3 weeks to promote the revascularization and biomechanical strength of the implant. Then, 2 cm length of the tubularized penile urethra was replaced by tissue-engineered bionic urethra. At 3 months of urethral replacement, USPIO-labeled tissue-engineered bionic urethra can be effectively detected by MRI at the transplant site. Histologically, the retrieved bionic urethras still displayed 3 layers, including an epithelial layer, a fibrous layer, and a myoblast layer. Three weeks after subcutaneous transplantation, immunofluorescence analysis showed the density of blood vessels in bionic urethra was significantly increased following the initial establishment of the constructs and was further up-regulated at 3 months after urethral replacement and was close to normal level in urethral tissue. Our study is the first to experimentally demonstrate 3-layer tissue-engineered urethras can be established using cell sheet technology and can promote the regeneration of structural and functional urethras similar to normal urethra.

Single-Walled Carbon Nanotubes Enhance the Efficiency and Stability of Mesoscopic Perovskite Solar Cells

Carbon nanotubes are 1D nanocarbons with excellent properties and have been extensively used in various electronic and optoelectronic device applications including solar cells. Herein, we report a significant enhancement in the efficiency and stability of perovskite solar cells (PSCs) by employing single-walled carbon nanotubes (SWCNTs) in the mesoporous photoelectrode. It was found that SWCNTs provide both rapid electron transfer and advantageously shifts the conduction band minimum of the TiO₂ photoelectrode and thus enhances all photovoltaic parameters of PSCs. The TiO₂-SWCNTs photoelectrode based PSC device exhibited a power conversion efficiency (PCE) of up to 16.11%, while the device fabricated without SWCNTs displayed an efficiency of 13.53%. More importantly, we found that the SWCNTs in the TiO₂ nanoparticles (TiO₂ NPs) based photoelectrode suppress the hysteresis behavior and significantly enhance both the light and long-term storage stability of the PSC devices. The present work provides important guidance for future investigations in utilizing carbonaceous materials for solar cells.

Multifunctional Core@Shell Magnetic Nanoprobes for Enhancing Targeted Magnetic Resonance Imaging and Fluorescent Labeling in Vitro and in Vivo

Core@shell magnetic nanoparticles (core@shell MNPs) are attracting widespread attention due to their enhancement properties for potential applications in hyperthermia treatment, magnetic resonance imaging (MRI), diagnostics, and so forth. Herein, we developed a facile thermal decomposition method for controllable synthesis of a superparamagnetic, monodispersed core@shell structure (Co@Mn = CoFe₂O₄@MnFe₂O₄) with uniform size distribution (σ < 5%, d_c ≈ 15 nm). The CoFe₂O₄ core could enhance magnetic anisotropy, and the MnFe₂O₄ shell could improve the magnetization value. The Co@Mn MNPs were transferred into aqueous solution with an amphiphilic polymer (labeled 2% TAMRA) and functionalized with PEG_2k and target molecules (folic acid, FA) to fabricate multifunctional PMA_TAMRA-Co@Mn-PEG_2k-FA nanoprobes. The obtained PMA_TAMRA-Co@Mn-PEG_2k-FA nanoprobes exhibit good biocompatibility, high T₂ relaxation values, and long-term fluorescence stability (at least 6 months). Our results demonstrate that the synthesized PMA_TAMRA-Co@Mn-PEG_2k-FA nanoprobes can effectively enhance the targeted MRI and fluorescent labeling in vitro and in vivo. The research outcomes will contribute to the rational design of new nanoprobes and provide a promising pathway to promote core@shell nanoprobes for further clinical contrast MRI and photodynamic therapy in the near future.

Carbon Nanotubes in TiO2 Nanofiber Photoelectrodes for High-Performance Perovskite Solar Cells

1D semiconducting oxides are unique structures that have been widely used for photovoltaic (PV) devices due to their capability to provide a direct pathway for charge transport. In addition, carbon nanotubes (CNTs) have played multifunctional roles in a range of PV cells because of their fascinating properties. Herein, the influence of CNTs on the PV performance of 1D titanium dioxide nanofiber (TiO2 NF) photoelectrode perovskite solar cells (PSCs) is systematically explored. Among the different types of CNTs, single-walled CNTs (SWCNTs) incorporated in the TiO2 NF photoelectrode PSCs show a significant enhancement (≈40%) in the power conversion efficiency (PCE) as compared to control cells. SWCNTs incorporated in TiO2 NFs provide a fast electron transfer within the photoelectrode, resulting in an increase in the short-circuit current (Jsc) value. On the basis of our theoretical calculations, the improved open-circuit voltage (Voc) of the cells can be attributed to a shift in energy level of the photoelectrodes after the introduction of SWCNTs. Furthermore, it is found that the incorporation of SWCNTs into TiO2 NFs reduces the hysteresis effect and improves the stability of the PSC devices. In this study, the best performing PSC device constructed with SWCNT structures achieves a PCE of 14.03%.

Carbon nanotube modified probes for stable and high sensitivity conductive atomic force microscopy

Conductive atomic force microscopy (C-AFM) is used to characterise the nanoscale electrical properties of many conducting and semiconducting materials. We investigate the effect of single walled carbon nanotube (SWCNT) modification of commercial Pt/Ir cantilevers on the sensitivity and image stability during C-AFM imaging. Pt/Ir cantilevers were modified with small bundles of SWCNTs via a manual attachment procedure and secured with a conductive platinum pad. AFM images of topography and current were collected from heterogeneous polymer and nanomaterial samples using both standard and SWCNT modified cantilevers. Typically, achieving a good current image comes at the cost of reduced feedback stability. In part, this is due to electrostatic interaction and increased tip wear upon applying a bias between the tip and the sample. The SWCNT modified tips displayed superior current sensitivity and feedback stability which, combined with superior wear resistance of SWCNTs, is a significant advancement for C-AFM.

Phosphorene and Phosphorene-Based Materials - Prospects for Future Applications

Phosphorene, a single- or few-layered semiconductor material obtained from black phosphorus, has recently been introduced as a new member of the family of two-dimensional (2D) layered materials. Since its discovery, phosphorene has attracted significant attention, and due to its unique properties, is a promising material for many applications including transistors, batteries and photovoltaics (PV). However, based on the current progress in phosphorene production, it is clear that a lot remains to be explored before this material can be used for these applications. After providing a comprehensive overview of recent advancements in phosphorene synthesis, advantages and challenges of the currently available methods for phosphorene production are discussed. An overview of the research progress in the use of phosphorene for a wide range of applications is presented, with a focus on enabling important roles that phosphorene would play in next-generation PV cells. Roadmaps that have the potential to address some of the challenges in phosphorene research are examined because it is clear that the unprecedented chemical, physical and electronic properties of phosphorene and phosphorene-based materials are suitable for various applications, including photovoltaics.

Accurate thickness measurement of graphene

Graphene has emerged as a material with a vast variety of applications. The electronic, optical and mechanical properties of graphene are strongly influenced by the number of layers present in a sample. As a result, the dimensional characterization of graphene films is crucial, especially with the continued development of new synthesis methods and applications. A number of techniques exist to determine the thickness of graphene films including optical contrast, Raman scattering and scanning probe microscopy techniques. Atomic force microscopy (AFM), in particular, is used extensively since it provides three-dimensional images that enable the measurement of the lateral dimensions of graphene films as well as the thickness, and by extension the number of layers present. However, in the literature AFM has proven to be inaccurate with a wide range of measured values for single layer graphene thickness reported (between 0.4 and 1.7 nm). This discrepancy has been attributed to tip-surface interactions, image feedback settings and surface chemistry. In this work, we use standard and carbon nanotube modified AFM probes and a relatively new AFM imaging mode known as PeakForce tapping mode to establish a protocol that will allow users to accurately determine the thickness of graphene films. In particular, the error in measuring the first layer is reduced from 0.1-1.3 nm to 0.1-0.3 nm. Furthermore, in the process we establish that the graphene-substrate adsorbate layer and imaging force, in particular the pressure the tip exerts on the surface, are crucial components in the accurate measurement of graphene using AFM. These findings can be applied to other 2D materials.

Synthesis of ultra-long hierarchical ZnO whiskers in a hydrothermal system for dye-sensitised solar cells

Ultra-long hierarchical ZnO whiskers (>100 μm) with tunable lengths through one-pot hydrothermal process have been demonstrated.

Ultrafine ferroferric oxide nanoparticles embedded into mesoporous carbon nanotubes for lithium ion batteries

An effective one-pot hydrothermal method for in situ filling of multi-wall carbon nanotubes (CNT, diameter of 20–40 nm, length of 30–100 μm) with ultrafine ferroferric oxide (Fe₃O₄) nanoparticles (8–10 nm) has been demonstrated. The synthesized Fe₃O₄@CNT exhibited a mesoporous texture with a specific surface area of 109.4 m² g⁻¹. The loading of CNT, in terms of the weight ratio of Fe₃O₄ nanoparticles, can reach as high as 66.5 wt%. Compared to the conventional method of using a Al₂O₃ membrane as template to fill CNT with iron oxides nanoparticles, our strategy is facile, effective, low cost and easy to scale up to large scale production (~1.42 g per one-pot). When evaluated for lithium storage at 1.0 C (1 C = 928 mA g⁻¹), the mesoporous Fe₃O₄@CNT can retain at 358.9 mAh g⁻¹ after 60 cycles. Even when cycled at high rate of 20 C, high capacity of 275.2 mAh g⁻¹ could still be achieved. At high rate (10 C) and long life cycling (500 cycles), the cells still exhibit a good capacity of 137.5 mAhg⁻¹.

Aligned Carbon Nanotube Thin Films from Liquid Crystal Polyelectrolyte Inks

Single walled carbon nanotube thin films are fabricated by solution shearing from high concentration sodium nanotubide polyelectrolyte inks. The solutions are produced by simple stirring of the nanotubes with elemental sodium in dimethylacetamide, and the nanotubes are thus not subject to any sonication-induced damage. At such elevated concentrations (∼4 mg mL(-1)), the solutions exist in the liquid crystal phase and during deposition this order is transferred to the films, which are well aligned in the direction of shear with a 2D nematic order parameter of ∼0.7 determined by polarized absorption measurements. Compared to similarly formed films made from superacids, the polyelectrolyte films contain smaller bundles and a much narrower distribution of bundle diameters. After p-doping with an organic oxidizer, the films exhibit a very high DC electrical to optical conductivity ratio of σ(DC)/σ(OP) ∼ 35, corresponding to a calculated DC conductivity of over 7000 S cm(-1). When very thin (T550 ∼ 96%), smooth (RMS roughness, R(q) ∼ 2.2 nm), and highly aligned films made via this new route are used as the front electrodes of carbon nanotube-silicon solar cells, the power conversion efficiency is almost an order of magnitude greater than that obtained when using the much rougher (R(q) ∼ 20-30 nm) and less conductive (peak σ(DC)/σ(OP) ∼ 2.5) films formed by common vacuum filtration of the same starting material, and having the same transmittance.

Membrane-drug interactions studied using model membrane systems

The direct interaction of drugs with the cell membrane is often neglected when drug effects are studied. Systematic investigations are hindered by the complexity of the natural membrane and model membrane systems can offer a useful alternative. Here some examples are reviewed of how model membrane architectures including vesicles, Langmuir monolayers and solid supported membranes can be used to investigate the effects of drug molecules on the membrane structure, and how these interactions can translate into effects on embedded membrane proteins.

A TiO2 Nanofiber-Carbon Nanotube-Composite Photoanode for Improved Efficiency in Dye-Sensitized Solar Cells

A light-scattering layer fabricated from electrospun titanium dioxide nanofibers (TiO2 -NFs) and single-walled carbon nanotubes (SWCNTs) formed a fiber-based photoanode. The nanocomposite scattering layer had a lawn-like structure and integration of carbon nanotubes into the NF photoanodes increased the power conversion efficiency from 2.9 % to 4.8 % under 1 Sun illumination. Under reduced light intensity (0.25 Sun), TiO2 -NF and TiO2 -NF/SWCNT-based DSSCs reached PCE values of up to 3.7 % and 6.6 %, respectively.

Carbon Nanotubes for Dye-Sensitized Solar Cells

As one type of emerging photovoltaic cell, dye-sensitized solar cells (DSSCs) are an attractive potential source of renewable energy due to their eco-friendliness, ease of fabrication, and cost effectiveness. However, in DSSCs, the rarity and high cost of some electrode materials (transparent conducting oxide and platinum) and the inefficient performance caused by slow electron transport, poor light-harvesting efficiency, and significant charge recombination are critical issues. Recent research has shown that carbon nanotubes (CNTs) are promising candidates to overcome these issues due to their unique electrical, optical, chemical, physical, as well as catalytic properties. This article provides a comprehensive review of the research that has focused on the application of CNTs and their hybrids in transparent conducting electrodes (TCEs), in semiconducting layers, and in counter electrodes of DSSCs. At the end of this review, some important research directions for the future use of CNTs in DSSCs are also provided.

Interaction of silver nanoparticles with tethered bilayer lipid membranes

Silver nanoparticles are well-known for their antibacterial properties. However, the detailed mechanism describing the interaction between the nanoparticles and a cell membrane is not fully understood, which can impede the use of the particles in biomedical applications. Here, a tethered bilayer lipid membrane has been used as a model system to mimic a natural membrane and to study the effect of exposure to small silver nanoparticles with diameters of about 2 nm. The solid supported membrane architecture allowed for the application of surface analytical techniques such as electrochemical impedance spectroscopy and atomic force microscopy. Exposure of the membrane to solutions of the silver nanoparticles led to a small but completely reversible perturbation of the lipid bilayer.

Characterization of the comparative drug binding to intra- (liver fatty acid binding protein) and extra- (human serum albumin) cellular proteins

1. This study compared the extent, affinity, and kinetics of drug binding to human serum albumin (HSA) and liver fatty acid binding protein (LFABP) using ultrafiltration and surface plasmon resonance (SPR). 2. Binding of basic and neutral drugs to both HSA and LFABP was typically negligible. Binding of acidic drugs ranged from minor (fu > 0.8) to extensive (fu < 0.1). Of the compounds screened, the highest binding to both HSA and LFABP was observed for the acidic drugs torsemide and sulfinpyrazone, and for β-estradiol (a polar, neutral compound). 3. The extent of binding of acidic drugs to HSA was up to 40% greater than binding to LFABP. SPR experiments demonstrated comparable kinetics and affinity for the binding of representative acidic drugs (naproxen, sulfinpyrazone, and torsemide) to HSA and LFABP. 4. Simulations based on in vitro kinetic constants derived from SPR experiments and a rapid equilibrium model were undertaken to examine the impact of binding characteristics on compartmental drug distribution. Simulations provided mechanistic confirmation that equilibration of intracellular unbound drug with the extracellular unbound drug is attained rapidly in the absence of active transport mechanisms for drugs bound moderately or extensively to HSA and LFABP.

Carbonaceous Dye-Sensitized Solar Cell Photoelectrodes

High photovoltaic efficiency is one of the most important keys to the commercialization of dye sensitized solar cells (DSSCs) in the quickly growing renewable electricity generation market. The heart of the DSSC system is a wide bandgap semiconductor based photoelectrode film that helps to adsorb dye molecules and transport the injected electrons away into the electrical circuit. However, charge recombination, poor light harvesting efficiency and slow electron transport of the nanocrystalline oxide photoelectrode film are major issues in the DSSC's performance. Recently, semiconducting composites based on carbonaceous materials (carbon nanoparticles, carbon nanotubes (CNTs), and graphene) have been shown to be promising materials for the photoelectrode of DSSCs due to their fascinating properties and low cost. After a brief introduction to development of nanocrystalline oxide based films, this Review outlines advancements that have been achieved in the application of carbonaceous-based materials in the photoelectrode of DSSCs and how these advancements have improved performance. In addition, several of the unsolved issues in this research area are discussed and some important future directions are also highlighted.

Solution processed graphene–silicon Schottky junction solar cells

Surfactant-assisted exfoliated graphene (SAEG) has been implemented in transparent conducting graphene films which, for the first time, were used to make SAEG–silicon Schottky junctions for photovoltaics.

Use of carbon nanotubes (CNTs) with polymers in solar cells

There is a clear need to make energy cheap, readily accessible and green, while ensuring its production does not contribute to further climate change. Of all the options available, photovoltaics offer the highest probability of delivering a meaningful and sustainable change in the way society produces its energy. One approach to the development of such photovoltaics involves the use of polymers. These systems offer the advantages of cheap production, flexibility (and hence a range of deployment opportunities) and tunability of light absorption. However, there are issues with polymer-based photovoltaic systems and one significant effort to improve these systems has involved the use of carbon nanotubes (CNTs). This review will focus on those efforts. CNTs have been used in virtually every component of the devices to help charge conduction, improve electrode flexibility and in some cases as active light absorbing materials.