The effect of the contact angle on particle stabilization and bridging in water-in-water emulsions

HYPOTHESIS

Water-in-water (W/W) emulsions formed by mixing incompatible polymers in aqueous solution can in some cases be stabilized by adding particles that adsorb spontaneously at the W/W interface. The importance of the contact angle of the particles with the interface on the stability of W/W emulsions is still an outstanding issue. We hypothesize that if the contact angle with the continuous phase is smaller than 90°, particles can bridge dispersed droplets, which enhances the stability of the emulsion.

EXPERIMENTS

The W/W emulsions consisted of a dispersed poly(ethylene oxide) (PEO) phase in a continuous dextran phase or vice versa. Gelatin microgels were added and their contact angle was varied by varying the pH. The morphology during aging was observed by microscopy.

FINDINGS

The contact angle of the microgels with the PEO phase varied between 110° close to neutral pH and 0° at pH 3 and pH 11. The W/W emulsions were stable only when the contact angle with the continuous phase was smaller than 90°. In this case, microgels could form bridges between dispersed droplets creating a network of droplets.

Dynamic gelation of shear-induced filamentous domains for cellulose ether assemblies due to polyion complexation

Assemblies of carbohydrate polymers are important in a number of applications and improved methods for their fabrication are increasingly sought after. Herein, we report that an aqueous two-phase system of alginate (Alg) and hydroxypropyl cellulose with poly(methacrylic acid) graft chains (HPC-PMA) facilitated the assembly of Alg/HPC-PMA in both phases. Dynamically formed filamentous domains in a flow field were gelled by rapid complexation with cationic polyethyleneimine (PEI). The fabricated HPC-PMA gel filament morphologies can be switched between the bundled and dissociated gel filaments using a co-flow microfluidic device in response to the amount of supplied PEI crosslinker. Excess complexation of PEI contributes to the fabrication of cationic gel filaments; this contribution results in a dissociated structure due to electrostatic repulsion. In contrast, an appropriate amount of PEI resulted in a bundle structure. The proposed spinning method avoids the risk of nozzle clogging, and enables the one-step spinning of multiple gel filaments.

Characterization of aqueous two phase systems by combining lab-on-a-chip technology with robotic liquid handling stations

Over the last decade, the use of design of experiment approaches in combination with fully automated high throughput (HTP) compatible screenings supported by robotic liquid handling stations (LHS), adequate fast analytics and data processing has been developed in the biopharmaceutical industry into a strategy of high throughput process development (HTPD) resulting in lower experimental effort, sample reduction and an overall higher degree of process optimization. Apart from HTP technologies, lab-on-a-chip technology has experienced an enormous growth in the last years and allows further reduction of sample consumption. A combination of LHS and lab-on-a-chip technology is highly desirable and realized in the present work to characterize aqueous two phase systems with respect to tie lines. In particular, a new high throughput compatible approach for the characterization of aqueous two phase systems regarding tie lines by exploiting differences in phase densities is presented. Densities were measured by a standalone micro fluidic liquid density sensor, which was integrated into a liquid handling station by means of a developed generic Tip2World interface. This combination of liquid handling stations and lab-on-a-chip technology enables fast, fully automated, and highly accurate density measurements. The presented approach was used to determine the phase diagram of ATPSs composed of potassium phosphate (pH 7) and polyethylene glycol (PEG) with a molecular weight of 300, 400, 600 and 1000 Da respectively in the presence and in the absence of 3% (w/w) sodium chloride. Considering the whole ATPS characterization process, two complete ATPSs could be characterized within 24h, including four runs per ATPS for binodal curve determination (less than 45 min/run), and tie line determination (less than 45 min/run for ATPS preparation and 8h for density determination), which can be performed fully automated over night without requiring man power. The presented methodology provides a cost, time and material effective approach for characterization of ATPS phase diagram on base on highly accurate and comprehensive data. By this means the derived data opens the door for a more detailed description of ATPS towards generating mechanistic based models, since molecular approaches such as MD simulations or molecular descriptions along the line of QSAR heavily rely on accurate and comprehensive data.