Ion-bombardment-driven surface modification of porous magnesium scaffolds: Enhancing biocompatibility and osteoimmunomodulation

Porous Mg scaffolds are promising for bone repair but are limited by high corrosion rates and challenges in preserving coating integrity. We used Directed Plasma Nanosynthesis (DPNS) at 400 eV and a fluence of 1 × 1018 cm-2 to augment the bioactivity and corrosion resistance of porous Mg scaffolds, maintaining their overall material integrity. DPNS creates nanostructures that increase surface area, promote apatite nucleation, and enhance osseointegration, improving the bioactivity and corrosion resistance of porous Mg scaffolds without compromising their structure. Our findings indicate a decrease in surface roughness, with pre-irradiated samples having Rq = 60.4 ± 5.3 nm andRa = 48.2 ± 3.1 nm, and post-DPNS samples showing Rq = 36.9 ± 0.3 nm andRa = 28.6 ± 0.8 nm. This suggests changes in topography and wettability, corroborated by the increased water contact angles (CA) of 129.2 ± 3.2 degrees. The complexity of the solution influences the CA: DMEM results in a CA of 120.4 ± 0.1 degrees, while DMEM + SBF decreases it to 103.6 ± 0.5 degrees, in contrast to the complete spreading observed in non-irradiated samples. DPNS-treated scaffolds exhibit significantly reduced corrosion rates at 5.7 × 10-3 ± 3.8 × 10-4 mg/cm²/day, compared to the control's 2.3 × 10-2 ± 3.2 × 10-4 mg/cm²/day over 14 days (P < 0.01). The treatment encourages the formation of a Ca-phosphate-rich phase, which facilitates cell spreading and the development of focal adhesion points in hBM-MSCs on the scaffolds. Additionally, J774A.1 murine macrophages show an enhanced immune response with diminished TNF-α cytokine expression. These results offer insights into nanoscale modifications of Mg-based biomaterials and their promise for bone substitutes or tissue engineering scaffolds.

Mechanical behaviour of a novel biomimetic lattice structure for bone scaffold

In this research, a new lattice structure based on the octagonal geometry and produced by Additive Manufacturing (AM) technique was proposed. Eight octagons with the same dimensions are combined to each other forming a ring. To obtain an isotropic lattice structure, cubic symmetry was imposed; thus, the unit cell is made of three rings mutually perpendicular, one ring for each principal direction. The aim of this study is the morphological and mechanical characterization of the novel unit cell to check its suitability to the biomechanical field, along with its comparison with other lattice structures currently used as bone scaffold. Electron Beam Melting (EBM) technique was used to produce Ti6Al4V ELI alloy specimens of the novel unit cell and of the truncated octahedron (Kelvin) cell. Three different unit cell sizes were selected to investigate the effect of cell dimensions on the mechanical properties. Morphological analysis was performed through a scanning electron microscope (SEM), to compare the actual structures to the designed ones. On the whole, the new lattice structure provided adequate mechanical properties to be considered as a bone substitute; further tests will be focused on its osteointegration capability.

The effect of oxygen pickup during selective laser melting on the microstructure and mechanical properties of Ti-6Al-4V lattices

Additive manufacturing techniques such as Selective Laser Melting (SLM) can produce complex shapes with relatively thin sections and fine detail. However, common materials for the process, such as Ti–6Al–4V, have microstructure and properties that are sensitive to the pickup of interstitial impurities, such as oxygen, which the material will be exposed to during the process. This problem would be especially severe for parts with thin sections, where surface effects can be more significant, and where poor properties may coincide with locally-elevated stress. Here we explore the effects of oxygen level in thin sections with the use of lattice materials (materials which can be considered to consist exclusively of near-surface material). Oxygen levels are artificially raised using repeated melting passes to result in more pickup, leading to significantly reduced ductility and hence reduced strength measured in compression. A ductile to brittle transition in strut failure mechanism is found with increasing number of melting passes, with significant modification in chemistry and crystallographic structure, despite the presence of a similar fine plate-like microstructure throughout.

The toxic mechanisms of BDE-47 to the marine diatom Thalassiosira pseudonana-a study based on multiple physiological processes

Polybrominated diphenyl ethers (PBDEs), a series of highly persistent organic pollutants (POPs), are ubiquitous in marine ecosystems. As key primary producers, microalgae are of great importance on evaluating the environmental outcome of PBDEs pollution. In this study, the toxic mechanisms of BDE-47 on the marine diatom Thalassiosira pseudonana were evaluated by measuring multiple physiological processes. Three concentrations of BDE-47 (25, 15 and 5 μg L^-1) were used along with two controls (blank: no BDE-47 or DMSO; negative control: only DMSO). Experiments lasted 144 h (6 days), in which the actual BDE-47 concentrations, cell densities, nutrient (nitrate and phosphate) uptake, pigment compositions, photosynthetic physiology, cell morphology and cellular contents (organic carbon and nitrogen) were measured at 12-48 h intervals. The toxic mechanisms of BDE-47 on T. pseudonana cells were evaluated by measuring multiple physiological processes including photosynthesis, nutrient uptake, cellular material synthesis and cell cycle progressions. The cell divisions of T. pseudonana were severely inhibited by the stress of BDE-47, but the photosynthetic parameters were much less declined and recovered earlier than the cell divisions in the same BDE-47 treatments. The unsuppressed uptake rates of nutrients, increased cell volume and cellular contents indicated the cellular material synthesis proceeded normally. Finally, we found that the cell cycle was arrested in G2/M phase under the stress of BDE-47, we thus concluded that the inhibition of cell divisions by BDE-47 was not due to the lack of energy or cellular materials, where the cell cycle arrest happened; this might be the most important toxicological outcome.

Linear and crosslinked Polyurethanes based catalysts for reduction of methylene blue

The large amount of synthetic dyes in effluents is a serious concern to be addressed. The chemical reduction is one of the potential way to resolve this problem. In this study, linear and crosslinked polyurethanes i.e. LPUR & CLPUR were synthesized from toluene diisocyanate (TDI), polyethylene glycol (PEG;1000g/mole) and tetraethylenepentamine (TEPA). The structure and morphology of synthesized materials were examined by FTIR, SEM and BET. The CLPUR was found stable in aqueous system with 0.80g/cm³ density and 16.4998m²g^-1 surface area. These materials were applied for the reduction of methylene blue in presence of NaBH₄. Both, polymers catalyzed the process and showed 100% reduction in 16 and 28mins., respectively, while, the reduction rate was significantly low in absence of these materials, even after 120mins. Furthermore, negligible adsorption was observed with only 7% removal of dye. The best reduction rates were observed at low concentration of dye, increasing concentration of NaBH₄ and with more dosage of polymeric catalyst. The kinetic study of process followed zero order kinetics. It was hence concluded that both synthesized polymers played a catalytic role in reduction process. However, stability in aqueous system and better efficiency in reduction process endorsed CLPUR as an optimal choice for further studies.

Determination of the mechanical properties of solid and cellular polymeric dosage forms by diametral compression

At present, the immediate-release solid dosage forms, such as the oral tablets and capsules, are granular solids. They release drug rapidly and have adequate mechanical properties, but their manufacture is fraught with difficulties inherent in processing particulate matter. Such difficulties, however, could be overcome by liquid-based processing. Therefore, we have recently introduced polymeric cellular (i.e., highly porous) dosage forms prepared from a melt process. Experiments have shown that upon immersion in a dissolution medium, the cellular dosage forms with polyethylene glycol (PEG) as excipient and with predominantly open-cell topology disintegrate by exfoliation, thus enabling rapid drug release. If the volume fraction of voids of the open-cell structures is too large, however, their mechanical strength is adversely affected. At present, the common method for determining the tensile strength of brittle, solid dosage forms (such as select granular forms) is the diametral compression test. In this study, the theory of diametral compression is first refined to demonstrate that the relevant mechanical properties of ductile and cellular solids (i.e., the elastic modulus and the yield strength) can also be extracted from this test. Diametral compression experiments are then conducted on PEG-based solid and cellular dosage forms. It is found that the elastic modulus and yield strength of the open-cell structures are about an order of magnitude smaller than those of the non-porous solids, but still are substantially greater than the stiffness and strength requirements for handling the dosage forms manually. This work thus demonstrates that melt-processed polymeric cellular dosage forms that release drug rapidly can be designed and manufactured to have adequate mechanical properties.

Melt-processed polymeric cellular dosage forms for immediate drug release

The present immediate-release solid dosage forms, such as the oral tablets and capsules, comprise granular matrices. While effective in releasing the drug rapidly, they are fraught with difficulties inherent in processing particulate matter. By contrast, liquid-based processes would be far more predictable; but the standard cast microstructures are unsuited for immediate-release because they resist fluid percolation and penetration. In this article, we introduce cellular dosage forms that can be readily prepared from polymeric melts by incorporating the nucleation, growth, and coalescence of microscopic gas bubbles in a molding process. We show that the cell topology and formulation of such cellular structures can be engineered to reduce the length-scale of the mass-transfer step, which determines the time of drug release, from as large as the dosage form itself to as small as the thickness of the cell wall. This allows the cellular dosage forms to achieve drug release rates over an order of magnitude faster compared with those of cast matrices, spanning the entire spectrum of immediate-release and beyond. The melt-processed polymeric cellular dosage forms enable predictive design of immediate-release solid dosage forms by tailoring microstructures, and could be manufactured efficiently in a single step.

Stress concentration around an atelectatic region: a finite element model

Lung parenchyma surrounding an atelectatic region is thought to be subjected to increased stress compared with the rest of the lung. Using 37 hexagonal cells made of linear springs, Mead et al. (1970) measured a stress concentration greater than 30% in the springs surrounding a stiffer central cell. We re-examine the problem using a 2D finite element model of 500 cells made of thin filaments with a non-linear stress-strain relationship. We study the consequences of increasing the central stiff region from one to nine contiguous cells in regular hexagonal honeycombs and random Voronoi honeycombs. The honeycomb structures were uniformly expanded with strains of 15%, 30%, 45% and 55% above their resting, non-deformed geometry. The curve of biaxial stress vs. fractional area change has a similar shape to that of the pressure-volume curve of the lung, showing an initial regime with relatively flat slope and a final regime with decreasing slope, tending toward an asymptote. Regular honeycombs had little variability in the maximum stress in radially oriented filaments adjacent to the central stiff region. In contrast, some filaments in random Voronoi honeycombs were subjected to stress concentration approximately 16 times the average stress concentration in the radially oriented filaments adjacent to the stiff region. These results may have implications in selecting the appropriate strategy for mechanical ventilation in ARDS and defining a "safe" level of alveolar pressure for ventilating atelectatic lungs.

The structure-mechanical relationship of palm vascular tissue

The structure-mechanical relationship of palm sheath is studied with numerical and experimental methods. The cellular structure of the vascular tissue is rebuilt with an image-based reconstruction method and used to create finite element models. The validity of the models is firstly verified with the results from the tensile tests. Then, the cell walls inside each of the specific regions (fiber cap, vessel, xylem, etc.) are randomly removed to obtain virtually imperfect structures. By comparing the magnitudes of performance degradation in the different imperfect structures, the influences of each region on the overall mechanical performances of the vascular tissue are discussed. The longitudinal stiffness and yield strength are sensitive to the defects in the vessel regions. While in the transverse directions (including the radial and tangential directions), the parenchymatous tissue determines the mechanical properties of the vascular tissue. Moreover, the hydraulic, dynamic response and energy absorption behavior of the vascular tissue are numerically explored. The flexibility of natural palm tissue enhances its impact resistance. Under the quasi-static compression, the cell walls connecting the fiber cap and the vessel dissipate more energy. The dominant role of the fiber cap in the plastic energy dissipation under high-speed impact is observed. And the radially-arranged fiber cap also allows the palm tissue to improve its tangential mechanical performances under hydraulic pressure.