Development of a novel green catalyzed nanostructured Cu(II) macrocyclic complex-based disposable electrochemical sensor for sensitive detection of bisphenol A in environmental samples

BPA is an endocrine disruptor and the leading environmental pollutant due to its use as raw material in industries. Therefore, the present work reports the sensitive, efficient, and disposable electrochemical paper-based SPE for determining the BPA sensor using an amide-based macrocyclic complex (nanostructured complex of copper acetate with macrocyclic ligand, i.e., CuL (CH3COO)2) synthesized using Citrus limon (lemon) extract via sonication for the first time. The structural, morphological, and electrochemical analyses have been characterized by mass spectroscopy, FTIR, UV-Vis, XRD, FESEM-EDX, elemental mapping and electrochemical techniques. The sensor platform for detecting BPA was fabricated by simple drop-casting on the disposable paper-based SPE using macrocyclic complex, i.e., CuL (CH3COO)2/SPE. After optimizing the conditions, CuL (CH3COO)2/SPE electrode was employed for determining BPA via CV with a wide linear range of 31 × 10-9 μM-0.205 μM, low LOD of 0.027 nM, and high sensitivity of 49.71 μA (log nM)-1 cm-2 having correlation coefficient (R2) of 0.976 which is quite better in compared to other reported SPE sensor for detection of BPA. Further, our sensor also showed good selectivity and reproducibility, in addition to detecting BPA in environmental samples (tube well water, river water and drain water) with acceptable recoveries and RSDs values. In this work, the combination of macrocyclic complex and paper-based SPE has turned out to be a cost-effective electrochemical sensor.

Nanostructured steady-state nanocarriers for nutrients preservation and delivery

Food bioactives possess specific physiological benefits of preventing certain diet-related chronic diseases or maintain human health. However, the limitations of the bioactives are their poor stability, lower water solubility and unacceptable bioaccessibility. Structure damage or degradation is often found for the bioactives under certain environmental conditions like high temperature, strong light, extreme pH or high oxygen concentration during food processing, packaging, storage and absorption. Nanostructured steady-state nanocarriers have shown great potential in overcoming the drawbacks for food bioactives. Various delivery systems including solid form delivery system, liquid form delivery system and encapsulation technology have been developed. The embedded food nutrients can largely decrease the loss and degradation during food processing, packaging and storage. The design and application of stimulus and targeted delivery systems can improve the stability, bioavailability and efficacy of the food bioactives upon oral consumption due to enzymatic degradation in the gastrointestinal tract. The food nutrients encapsulated in the smart delivery system can be well protected against degradation during oral administration, thus improving the bioavailability and releazing controlled or targeted release for food nutrients. The encapsulated food bioactives show great potential in nutrition therapy for sub-health status and disease. Much effort is required to design and prepare more biocompatible nanostructured steady-state nanocarriers using food-grade protein or polysaccharides as wall materials, which can be used in food industry and maintain the human health.

Biosensors for the detection of disease outbreaks through wastewater-based epidemiology

Wastewater-Based Epidemiology (WBE) is a novel community-wide monitoring tool that provides comprehensive real-time data of the public and environmental health status and can contribute to public health interventions, including those related to infectious disease outbreaks (e.g., the ongoing COVID-19 pandemic). Nonetheless, municipalities without centralized laboratories are likely still not able to process WBE samples. Biosensors are a potentially cost-effective solution to monitor the development of diseases through WBE to prevent local outbreaks. This review discusses the economic and technical feasibility of eighteen recently developed biosensors for the detection and monitoring of infectious disease agents in wastewater, prospecting the prevention of future pandemics.

Highly sensitive and selective nanostructured microbiosensors for glucose and lactate simultaneous measurements in blood serum and in vivo in brain tissue

Highly sensitive and selective nanostructured lactate and glucose microbiosensors for their in vivo simultaneous determination in rat brain were developed based on carbon fiber microelectrodes (CFM) modified with nanoporous gold (NPG) using the Dynamic Hydrogen Bubble Template (DHBT) method. Electrodeposition of platinum nanoparticles (PtNP) onto the NPG film enhances the sensitivity and the electrocatalytic properties towards H₂O₂ detection. The nanostructured microelectrode platform was modified by glucose oxidase (GOx) and lactate oxidase (LOx) enzyme immobilization. High selective measurements were achieved by covering with a perm-selective layer of electropolymerized m-phenylenediamine, deposition of a Nafion® film and by using a null sensor. The morphological characteristics and electroanalytical performance of the microbiosensors were assessed, by scanning electron microscopy and electrochemical techniques, respectively. The PtNP/NPG/CFM shows a high sensitivity to H₂O₂ (5.96 A M^-1 cm^-2) at 0.36 V vs. Ag/AgCl, with a linear range from 0.2 to 200 μM, and an LOD of 10 nM. The microbiosensors were applied to the simultaneous determination of lactate and glucose in blood serum samples. Moreover, the basal extracellular concentrations of lactate and glucose were measured in vivo in four different rat brain structures. These results support the potential of the microbiosensor to be used as a valuable tool to investigate brain neurochemicals in vivo.

Stimuli-responsive biphenyl-tripeptide supramolecular hydrogels as biomimetic extracellular matrix scaffolds for cartilage tissue engineering

Supramolecular hydrogel composed of aromatic short peptide gelator was an attractive biomaterial owing to its simple and convenient synthetic route, nano-fibrillar microstructure resembling natural collagen fibers and intelligent response to external stimulus. Herein, stimuli-responsive biphenyl-tripeptide supramolecular hydrogels was prepared to simulate extracellular matrix scaffolds by temperature switch, ion induction and pH switch. The amino acid arrangement substantially affected gelation behavior, only BPAA-βAFF and BPAA-FFβA could form nanostructured supramolecular hydrogels with 8-10 nm nanotubes or nanofibers by potential intermolecular hydrogen bond interactions and π-π stacking. The minimum gelation concentration (MGC) and maximum storage modulus were 0.4 mM (0.023 wt%) and around 8.2 KPa. The two supramolecular hydrogels could support adhesion and proliferation of L929 cells. Moreover, the BPAA-βAFF hydrogel promoted proliferation and ECM secretion of chondrocytes in vitro, and facilitate the phenotype maintenance of hyaline cartilage. All the results demonstrated that BPAA-βAFF hydrogel hold great potential application prospects in cartilage tissue engineering. STATEMENT OF SIGNIFICANCE: Diphenylalanine was served as a core segment conjugating with 4-biphenylacetic acid (BPAA) to produce biphenyl-tripeptide compounds with transforming amino sequence, and multiple external stimuli was applied to study the gelation properties of the aromatic short peptide gelators. "FF" brick (phenylalanine-phenylalanine) was crucial for formation of fibrous supramolecular hydrogels. Meanwhile, the sequence of amino acids arrangement also had an essential effect on the gelation behavior. Optimal BPAA-βAFF with ultra-low minimum gelation concentration (0.4 mM, about 0.023 wt%) and similar microstructure to extracellular matrix (ECM) of nature cartilage tissue could promote the proliferation and ECM secretion of chondrocytes in vitro, and facilitate the formation of hyaline cartilage.

Application of FTIR-ATR spectroscopy to confirm the microwave assisted synthesis and curing of Cashew nut shell liquid derived nanostructured materials

The present work reports the development of nanostructured material from Cashew nut shell liquid (CNSL, an agro byproduct of cashew industry, 87% cardanol) to evaluate their potential in antibacterial applications as a substitute of petroleum feedstock via an energy-efficient method. The nanostructured material was synthesized by coordination polymerization reaction of cardanol and divalent Mn(II) salt with the aid of microwave irradiations. FTIR spectroscopy was used to confirm the proposed structure of the synthesized materials. FTIR-ATR spectroscopy was employed to verify the curing of material by comparing the spectra of the cured samples with the frequencies of uncured samples. Magnetic moment and UV-visible spectroscopy were used to confirm the proposed structure of the material further. Morphology of the synthesized material was investigated by XRD, optical microscopy, SEM and TEM and thermal behaviour by TGA/DTG/DSC technique. Agar diffusion method was utilized to investigate the antibacterial activity of the synthesized material against bacterial strains E. coli, K. pneumoniae, B. subtilis and S. aureus. N₂ adsorption-desorption was investigated to check BET specific surface area and BJH pore size distribution of the same. The results revealed that the synthesized materials were obtained as semicrystalline, porous, thermally stable and nanostructured film forming materials with moderate to good antibacterial activity against different nosocomial bacteria. They can be used as thermally stable antibacterial agents in the field of films/coatings for health care applications.

Preparation of hydroxyapatite nanostructures with different morphologies and adsorption behavior on seven heavy metals ions

Hydroxyapatite (HAP) nanostructures with different morphologies have been successfully synthesized in a facile method and the pH value of the solution has an important effect on morphology. Among them, the porous HAP nanospheres (NSs) with an average diameter of 76 nm were further employed as adsorbent to remove the heavy metal ions in solution. The BET surface area, pore size and pore volume of porous HAP NSs were 45.3 m²·g^-1, 2.7 nm and 0.23 m³·g^-1, respectively. The ICP results showed that the porous HAP NSs could remove effectively Pb²⁺, Cd²⁺, Cu²⁺, Co²⁺, Ni²⁺, Zn²⁺, Hg²⁺ ions and the maximum adsorption capacity reached 254.90 mg·g^-1. Experimental equilibrium data were also analyzed by the Langmuir and Freundlich models and the best fit was obtained with the Langmuir isotherm equation. The kinetic study indicated that the adsorption of Pb²⁺ ions on porous HAP NSs was almost instantaneous and the maximum adsorption was reached within 20 min. Compared with the pseudo 1st order model, the adsorption kinetic data was well described by the pseudo 2rd kinetic model. In addition, the porous HAP NSs had a good stability and would be a promising nanoadsorbent for heavy metal ions.

Fabrication techniques enabling ultrathin nanostructured membranes for separations

The fabrication of nanostructured materials is an area of continuous improvement and innovative techniques that fulfill the demand of many fields of research and development. The continuously decreasing size of the smallest patternable feature has expanded the catalog of methods enabling the fabrication of nanostructured materials. Several of these nanofabrication techniques have sprouted from applications requiring nanoporous membranes such as molecular separations, cell culture, and plasmonics. This review summarizes methods that successfully produce through-pores in ultrathin films exhibiting an approximate pore size to thickness ratio of one, which has been shown to be beneficial due to high permeability and improved separation potential. The material reviewed includes large-area, parallel, and affordable approaches such as self-organizing polymers, nanosphere lithography, anodization, nanoimprint lithography as well as others such as solid phase crystallization and nanosphere lens lithography. The aim of this review is to provide a set of inexpensive fabrication techniques to produce nanostructured materials exhibiting pores ranging from 10 to 350 nm and a pore size to thickness ratio close to one. The fabrication methods described in this work have reported the successful manufacture of nanoporous membranes exhibiting the ideal characteristics to improve selectivity and permeability when applied as separation media in ultrafiltration.

The safety of nanostructured synthetic amorphous silica (SAS) as a food additive (E 551)

KEY MESSAGES

Particle sizes of E 551 products are in the micrometre range. The typical external diameters of the constituent particles (aggregates) are greater than 100 nm. E 551 does not break down under acidic conditions such as in the stomach, but may release dissolved silica in environments with higher pH such as the intestinal tract. E 551 is one of the toxicologically most intensively studied substances and has not shown any relevant systemic or local toxicity after oral exposure. Synthetic amorphous silica (SAS) meeting the specifications for use as a food additive (E 551) is and has always been produced by the same two production methods: the thermal and the wet processes, resulting in E 551 products consisting of particles typically in the micrometre size range. The constituent particles (aggregates) are typically larger than 100 nm and do not contain discernible primary particles. Particle sizes above 100 nm are necessary for E 551 to fulfil its technical function as spacer between food particles, thus avoiding the caking of food particles. Based on an in-depth review of the available toxicological information and intake data, it is concluded that the SAS products specified for use as food additive E 551 do not cause adverse effects in oral repeated-dose studies including doses that exceed current OECD guideline recommendations. In particular, there is no evidence for liver toxicity after oral intake. No adverse effects have been found in oral fertility and developmental toxicity studies, nor are there any indications from in vivo studies for an immunotoxic or neurotoxic effect. SAS is neither mutagenic nor genotoxic in vivo. In intact cells, a direct interaction of unlabelled and unmodified SAS with DNA was never found. Differences in the magnitude of biological responses between pyrogenic and precipitated silica described in some in vitro studies with murine macrophages at exaggerated exposure levels seem to be related to interactions with cell culture proteins and cell membranes. The in vivo studies do not indicate that there is a toxicologically relevant difference between SAS products after oral exposure. It is noted that any silicon dioxide product not meeting established specifications, and/or produced to provide new functionality in food, requires its own specific safety and risk assessment.

Polythiophene/graphene oxide nanostructured electrodeposited coating for on-line electrochemically controlled in-tube solid-phase microextraction

In this work, a novel polythiophene/graphene oxide (PTh/GO) nanostructured coating was introduced for on-line electrochemically-controlled in-tube solid phase microextraction of amitriptyline (AMI) and doxepin (DOX) as antidepressant drugs. The PTh/GO coating was prepared on the inner surface of a stainless steel tube by a facile in-situ electro-deposition method and it was used as a working electrode for electrochemically control in-tube solid phase microextraction. In the PTh/GO coating, GO acts as an anion dopant and sorbent. The PTh/GO coating, compared to PTh and GO coatings, exhibited enhanced long lifetime, good mechanical stability and a large specific surface area. Regarding the in-tube SPME, some important factors such as the extraction and desorption voltage, extraction and desorption times and flow rates of the sample solution and eluent, which could affect the extraction and separation efficiency of the analytes, were optimized. Total analysis time of this method including the online extraction and desorption time was about 21min for each sample. AMI and DOX were extracted, separated and determined with limits of detection as small as 0.3μgL^-1 and 0.5μgL^-1, respectively. This method showed good linearity in the range of 0.7-200μgL^-1, 2.3-200μgL^-1 and 2.9-200μgL^-1 for AMI, and in the range 0.9-200μgL^-1, 2.5-200μgL^-1 and 3.0-200μgL^-1 for DOX in water, urine and plasma samples, respectively; the coefficients of determination were also equal to or higher than 0.9976. The inter- and intra-assay precisions (RSD%, n=3) were in the range of 2.8-3.4% and 2.9-3.9% at the three concentration levels of 5, 25 and 50μgL^-1, respectively. Finally, under the optimal conditions, the method was applied for the analysis of the drugs in human urine and plasma pretreated samples and good results were obtained.

Mechanically reliable thermoelectric (TE) nanocomposites by dispersing and embedding TE-nanostructures inside a tetragonal ZrO2 matrix: the concept and experimental demonstration in graphene oxide-3YSZ system

Novel low-dimensional thermoelectric (TE) materials suffer from poor mechanical reliability, which limits their applications, especially in mechanically harsh environments. Here, we propose a new concept, in which the novel, abundant, thermally stable TE-nanostructures are dispersed and then intimately embedded inside a protective, mechanically reliable tetragonal ZrO2 (TZP) ceramic matrix with a low thermal conductivity. We also demonstrate an experimental proof-of-principle verification of our concept in reduced-graphene oxide (GO)-3 mol% Y2O3-ZrO2 (3YSZ or 3Y-TZP) nanocomposite system. TE characterizations suggest that our protective TZP matrix does not degrade the intrinsic TE property of the reduced GO network. These preliminary results are promising and encouraging to start research on similar TZP-matrix TE-nanocomposites, which contain more effective TE-nanostructures with larger intrinsic power factors. In this regard, we propose a scalable approach for fabrication of similar dense TE-nanocomposites composed of other one-dimensional and/or two-dimensional TE-nanostructures, which involves an aqueous colloidal approach and a subsequent spark plasma sintering. These new TZP-matrix TE-nanocomposites could be used for sustainable clean power generation, especially in mechanically harsh environments with thermal/mechanical shocks and vibrations, where energy availability, reliability and durability are more important than the energy efficiency. Considering the excellent biocompatibility of TZP matrix, they could even be used inside the body to power implanted medical devices.