Cellulose-Assisted Vertically Heterostructured PEO-Based Solid Electrolytes Mitigating Li-Succinonitrile Corrosion for Lithium Metal Batteries

In the field of solid-state lithium metal batteries (SSLMBs), constructing vertically heterostructured poly(ethylene oxide) (PEO)-based solid electrolytes is an effective method to realize their tight contact with cathodes and Li anodes at the same time. Succinonitrile (SN) has been widely used in PEO-based solid electrolytes to improve the interface contact with cathodes, enhance the ionic conductivities, and obtain a high electrochemical stability window of PEO, but its application is still hindered by its intrinsic instability to Li anodes, which results in corrosion and side interactions with lithium metal. Herein, the cellulose membrane (CM) is introduced creatively into the vertically heterostructured PEO-based solid electrolytes to match the PEO-SN solid electrolytes at the cathode side. With the advantage of the interaction between -OH groups of CM and -C≡N groups in SN, the movement of free SN molecules from cathodes to Li anodes is limited effectively, resulting in a stable and durable SEI layer. In specific, the Li||LiFePO₄ battery with the CM-assisted vertically heterostructured PEO-based solid electrolyte by in situ preparation delivers a discharge capacity of around 130 mAh g^-1 after 300 cycles and capacity retention of 95% after 500 cycles at 0.5 C. Our work provides a solution to construct PEO-based solid electrolytes feasible to match cathodes and Li anodes effectively by intimate contact with electrodes.

Preparation and Synergy of Supported Ru0 and Pd0 for Rapid Chlorate Reduction at pH 7

Chlorate (ClO₃^-) is a common water pollutant due to its gigantic scale of production, wide applications in agriculture and industry, and formation as a toxic byproduct in various water treatment processes. This work reports on the facile preparation, mechanistic elucidation, and kinetic evaluation of a bimetallic catalyst for highly active ClO₃^- reduction into Cl^-. Under 1 atm H₂ and 20 °C, Pd^II and Ru^III were sequentially adsorbed and reduced on a powdered activated carbon support, affording Ru⁰-Pd⁰/C from scratch within only 20 min. The Pd⁰ particles significantly accelerated the reductive immobilization of Ru^III as >55% dispersed Ru⁰ outside Pd⁰. At pH 7, Ru-Pd/C shows a substantially higher activity of ClO₃^- reduction (initial turnover frequency >13.9 min^-1 on Ru⁰; rate constant at 4050 L h^-1 g_metal^-1) than reported catalysts (e.g., Rh/C, Ir/C, Mo-Pd/C) and the monometallic Ru/C. In particular, Ru-Pd/C accomplished the reduction of concentrated 100 mM ClO₃^- (turnover number > 11,970), whereas Ru/C was quickly deactivated. In the bimetallic synergy, Ru⁰ rapidly reduces ClO₃^- while Pd⁰ scavenges the Ru-passivating ClO₂^- and restores Ru⁰. This work demonstrates a simple and effective design for heterogeneous catalysts tailored for emerging water treatment needs.

An In Situ Prepared Comb-like Polycaprolactone-Based Gel Electrolyte for High-Performance Lithium Metal Batteries

Herein, we present the synthesis and electrochemical performance of a comb-like polycaprolactone-based gel electrolyte from acrylate terminated polycaprolactone oligomers and liquid electrolyte for high-voltage lithium metal batteries. The ionic conductivity of this gel electrolyte at room temperature was measured to be 8.8 × 10^-3 S cm^-1, which is an exceptionally high value that is more than sufficient for the stable cycling of solid-state lithium metal batteries. The Li⁺ transference number was detected to be 0.45, facilitating the prohibition of concentration gradients and polarization, thereby prohibiting lithium dendrite formation. In addition, the gel electrolyte exhibits high oxidation voltage up to 5.0 V vs. Li⁺/Li and perfect compatibility against metallic lithium electrodes. The superior electrochemical properties provide the LiFePO₄-based solid-state lithium metal batteries with excellent cycling stability, displaying a high initial discharge capacity of 141 mAh g^-1 and an extraordinary capacity retention exceeding 74% of its initial specific capacity after being cycled for 280 cycles at 0.5C at room temperature. This paper presents a simple and effective in situ preparation process yielding an excellent gel electrolyte for high-performance lithium metal battery applications.

Unusually Dispersed AgI Quantum Dots For Efficient HTL-Free CH3NH3PbI3 Photovoltaics

The utilization of quantum dots (QDs) to improve the performance of perovskite solar cells is attracting much attention due to their unique optical and electronic properties. Most of QDs have to be prepared in advance and then incorporated into the perovskite hosts, which could not ensure the maintenance of their QD characteristics. In this work, we intelligently developed an in situ preparation strategy to disperse AgI QDs homogeneously in the perovskite host for the MAPbI₃:AgI(QDs) cross-blended layer directly on indium tin oxide (ITO) via a common and convenient spin-coating process. We combine transmission electron microscopy, X-ray photoelectron spectroscopy, and Raman techniques to demonstrate the cross-blended MAPbI₃:AgI(QDs) structure in the final perovskite devices. Furthermore, a series of simply inverted ITO/MAPbI₃:AgI(QDs)/PCBM/Ag devices have been designed and fabricated. The photovoltaic performance of these solar cells shows significantly improved short-circuit current density (J_sc) and a champion power conversion efficiency of 16.41% even without a hole transport layer. The current technique induced the crystal growth toward high-quality perovskite films with a homogeneous structure, good crystallinity, less grain boundaries and defects, increased optical path length, and uniform thickness for better solar cell performance. Besides, the impact of the current strategy also lies in an accommodation effect of the hole collection at the ITO side induced by AgI QDs, which modifies the Fermi level of perovskite films, leading to significantly decreased level difference in the Fermi level/work function between the perovskite layer and ITO substrates by ultraviolet photoelectron spectra analysis. More importantly, the charge carrier dynamics of such novel MAPbI₃:AgI(QDs) structures were also scrutinized by transient photovoltage analysis.

Ultrafast Response Polyelectrolyte Humidity Sensor for Respiration Monitoring

Respiration monitoring is important for evaluating human health. Humidity sensing is a promising way to establish a relationship between human respiration and electrical signal. This work describes polymer humidity sensors with ultrafast response for respiration monitoring. The humidity-sensitive polyelectrolyte is in situ cross-linked on the substrate printed with interdigitated electrodes by a thiol-ene click reaction. The polyelectrolyte humidity sensor shows rapid water adsorption/desorption ability, excellent stability, and repeatability. The sensor with ultrafast response and recovery (0.29/0.47 s) when changing humidity between 33 and 95% shows good application prospects in breath monitoring and touchless sensing. Different respiration patterns can be distinguished, and the breath rate/depth of detection subjects can also be determined by the sensor. In addition, the obtained sensor can sense the skin evaporation in a noncontact way.

Ultrahigh-vacuum organic molecular-beam deposition system for in situ growth and characterization

A compact ultrahigh-vacuum molecular-beam deposition system has been developed for the in situ synthesis of organic thin films and multilayers. The system incorporates all the features (heater, thickness monitor, evaporators) necessary for controlled organic thin-film growth. It can be used independently, or it can be docked to the in situ growth system and transferred to other instruments of the PGM beamline, thus allowing extensive film preparation and characterization. A manipulator dedicated to specimen preparation and organic-film deposition with temperature control between 200 K and ∼800 K has been developed. The design and performance of the system are reported with emphasis on a novel solution of masks developed to achieve position-dependent film deposition. To demonstrate the enhanced capabilities of the PGM beamline in the growth and in the characterization of electronic-structure studies of organic molecular films and their heterostructures through synchrotron-based spectroscopies, this paper presents some preliminary results of a study of Fe-phthalocyanine growth on Si substrates and on in situ prepared La_0.67Sr_0.33MnO₃ buffer layers on SrTiO₃ single crystal.

Interface Re-Engineering of Li10GeP2S12 Electrolyte and Lithium anode for All-Solid-State Lithium Batteries with Ultralong Cycle Life

An ingenious interface re-engineering strategy was applied to in situ prepare a manipulated LiH₂PO₄ protective layer on the surface of Li anode for circumventing the intrinsic chemical stability issues of Li₁₀GeP₂S₁₂ (LGPS) to Li metal, specifically the migration of mixed ionic-electronic reactants to the inner of LGPS, and the kinetically sluggish reactions in the interface. As consequence, the stability of LGPS with Li metal increased substantially and the cycling of symmetric Li/Li cell showed that the polarization voltage could keep relative stable for over 950 h at 0.1 mA cm^-2 within ±0.05 V. The optimized ASSLiB of LiCoO₂ (LCO)/LGPS/Li with interface-engineered structure was able to deliver long cycle life and high capacity, i.e., a reversible discharge capacity of 131.1 mAh g^-1 at the initial cycle and 113.7 mAh g^-1 at the 500th cycle under 0.1 C with a retention of 86.7%. In addition, the factors effected on the interphases formation of the LGPS/Li interface were analyzed, and the mechanism of the stability between LGPS and Li anode with protective layer was further investigated. Moreover, the probable causes of battery degradation were also explored. Above all, this work would give an alternative strategy for the modification of Li anode in high energy density solid-state lithium metal batteries.

Intramolecular Self-Enhanced Nanochains Functionalized by an Electrochemiluminescence Reagent and Its Immunosensing Application for the Detection of Urinary β2-Microglobulin

In this study, polyethylenimine (PEI) is discovered to possess a noticeable amplification effect for the electrochemiluminescence (ECL) of N-(aminobutyl)-N-(ethylisoluminol) (ABEI); thus, a novel self-enhanced ECL reagent (ABEI-PEI) is prepared by covalent cross-linking. Because of the shortened electron-transfer path and reduced energy loss, the intramolecular ECL reaction between ABEI and PEI exhibited enhanced luminous efficiency compared with the traditional intermolecular ECL reaction. Owing to the amine-rich property of PEI, abundant ABEI could be immobilized on the molecular chains of PEI to strengthen the luminous intensity of ABEI-PEI. On account of the reducibility of remaining amino groups, ABEI-PEI, as the self-enhanced ECL reagent, has also been chosen as a reductant and stabilizer for in situ preparation of Au@Ag nanochains (Au@AgNCs) which has the catalytic activity for the ECL reaction. Moreover, using ABEI-PEI as a template to directly prepare Au@AgNCs realizes the immobilization of the ECL reagent with large amounts. Meanwhile, in virtue of the electropositivity of ABEI-PEI-capped Au@AgNCs (ABEI-PEI-Au@AgNCs), polyacrylic acid (PAA) with electronegativity is pervaded on the surface of nanochains and further chelates with Co²⁺ to form an ABEI-PEI-Au@AgNCs-PAA/Co²⁺ complex, which could introduce Co²⁺ as a catalyst to promote H₂O₂ decomposition and thus oxidize ABEI to produce an enhanced ECL signal. Here, the obtained self-enhanced ABEI-PEI-Au@AgNCs-PAA/Co²⁺ complex is utilized to capture the detection antibody (Ab₂). According to sandwiched immunoreactions, a sensitive ECL immunosensor is constructed for the detection of β2-microglobulin with a wide linearity from 0.01 pg mL^-1 to 200 ng mL^-1 and a detection limit of 3.3 fg mL^-1.

Silver Nanoparticle Generators: Silicon Dioxide Microspheres

A green and simple approach has been developed to synthesize un-coated Ag nanoparticles (AgNPs) in situ on the surface of thiol-group-functionalized silica dioxide microspheres (TSMs) in the aqueous solution. As soon as the Ag⁺ ions attach onto the surface of TSMs, nucleation and growth of AgNPs can spontaneously complete within one minute without other reducing agents or capping agents. The main reason is that the self-assembled silane-layer formed by mercaptosilane molecules could reduce the Ag⁰ formation energy, transport electrons efficiently, improve the nucleation density, and protect AgNPs against oxidation. Thus, the supported AgNPs show excellent chemical/photochemical stability in air and solution. Meanwhile, the size of as-prepared AgNPs could be controlled by tuning the concentration of Ag⁺ ions. This process provides a general route to generate bare AgNPs on the surface of silica dioxide in situ, which might be extended to other materials and is promising in developing novel methodologies for making supported noble metal NPs with desired structure and properties.

In Situ Preparation of Metal Halide Perovskite Nanocrystal Thin Films for Improved Light-Emitting Devices

Hybrid organic-inorganic halide perovskite semiconductors are attractive candidates for optoelectronic applications, such as photovoltaics, light-emitting diodes, and lasers. Perovskite nanocrystals are of particular interest, where electrons and holes can be confined spatially, promoting radiative recombination. However, nanocrystalline films based on traditional colloidal nanocrystal synthesis strategies suffer from the use of long insulating ligands, low colloidal nanocrystal concentration, and significant aggregation during film formation. Here, we demonstrate a facile method for preparing perovskite nanocrystal films in situ and that the electroluminescence of light-emitting devices can be enhanced up to 40-fold through this nanocrystal film formation strategy. Briefly, the method involves the use of bulky organoammonium halides as additives to confine crystal growth of perovskites during film formation, achieving CH₃NH₃PbI₃ and CH₃NH₃PbBr₃ perovskite nanocrystals with an average crystal size of 5.4 ± 0.8 nm and 6.4 ± 1.3 nm, respectively, as confirmed through transmission electron microscopy measurements. Additive-confined perovskite nanocrystals show significantly improved photoluminescence quantum yield and decay lifetime. Finally, we demonstrate highly efficient CH₃NH₃PbI₃ red/near-infrared LEDs and CH₃NH₃PbBr₃ green LEDs based on this strategy, achieving an external quantum efficiency of 7.9% and 7.0%, respectively, which represent a 40-fold and 23-fold improvement over control devices fabricated without the additives.

In Situ Formation of Polysulfonamide Supported Poly(ethylene glycol) Divinyl Ether Based Polymer Electrolyte toward Monolithic Sodium Ion Batteries

Sodium ion battery is one of the promising rechargeable batteries due to the low-cost and abundant sodium sources. In this work, a monolithic sodium ion battery based on a Na₃ V₂ (PO₄ )₃ cathode, MoS₂ layered anode, and polyether-based polymer electrolyte is reported. In addition, a new kind of polysulfonamide-supported poly(ethylene glycol) divinyl ether based polymer electrolyte is also demonstrated for monolithic sodium ion battery via in situ preparation. The resultant polymer electrolyte exhibits relatively high ionic conductivity (1.2 mS cm^-1 ) at ambient temperature, wide electrochemical window (4.7 V), and favorable mechanical strength (25 MPa). Moreover, such a monolithic Na₃ V₂ (PO₄ )₃ /MoS₂ sodium ion battery using this polymer electrolyte delivers outstanding rate capability (up to 10 C) and superior cyclic stability (84%) after 1000 cycles at 0.5 C. What is more essential, such a polymer electrolyte based soft-package monolithic sodium ion cell can still power a red light emitting diode lamp and run finite times without suffering from any internal short-circuit failures, even in the case of a bended and wrinkled state. Considering these aspects, this work no doubt provides a new approach for the design of a high-performance polymer electrolyte toward monolithic sodium ion battery with exceptional rate capability and high safety.

Kölliker-Fuse nuclei regulate respiratory rhythm variability via a gain-control mechanism

Respiration varies from breath to breath. On the millisecond timescale of spiking, neuronal circuits exhibit variability due to the stochastic properties of ion channels and synapses. Does this fast, microscopic source of variability contribute to the slower, macroscopic variability of the respiratory period? To address this question, we modeled a stochastic oscillator with forcing; then, we tested its predictions experimentally for the respiratory rhythm generated by the in situ perfused preparation during vagal nerve stimulation (VNS). Our simulations identified a relationship among the gain of the input, entrainment strength, and rhythm variability. Specifically, at high gain, the periodic input entrained the oscillator and reduced variability, whereas at low gain, the noise interacted with the input, causing events known as "phase slips", which increased variability on a slow timescale. Experimentally, the in situ preparation behaved like the low-gain model: VNS entrained respiration but exhibited phase slips that increased rhythm variability. Next, we used bilateral muscimol microinjections in discrete respiratory compartments to identify areas involved in VNS gain control. Suppression of activity in the nucleus tractus solitarii occluded both entrainment and amplification of rhythm variability by VNS, confirming that these effects were due to the activation of the Hering-Breuer reflex. Suppressing activity of the Kölliker-Fuse nuclei (KFn) enhanced entrainment and reduced rhythm variability during VNS, consistent with the predictions of the high-gain model. Together, the model and experiments suggest that the KFn regulates respiratory rhythm variability via a gain control mechanism.

Measurement of contractile force of skeletal and extraocular muscles: effects of blood supply, muscle size and in situ or in vitro preparation

Contractile forces can be measured in situ and in vitro. To maintain metabolic viability with sufficient diffusion of oxygen, established guidelines for in vitro skeletal muscle preparations recommend use of relatively thin muscles (< or =1.25 mm thick). Nevertheless, forces of thin extraocular muscles vary substantially between studies. Here, we examined parameters that affect force measurements of in situ and in vitro preparations, including blood supply, nerve stimulation, direct muscle stimulation, muscle size, oxygenated or non-oxygenated buffer solutions and the time after interruption of vascular circulation. We found that the absolute forces of extraocular muscle are substantially lower when examined in vitro. In vitro preparation of 0.58 mm thick extraocular muscle from 3-week-old birds underestimated contractile function, but not of thinner (0.33 mm) muscle from 2-day-old birds. Our study shows that the effective criteria for functional viability, tested in vitro, differ between extraocular and other skeletal muscle. We conclude that contractile force of extraocular muscles will be underestimated by between 10 and 80%, when measurements are made after cessation of blood supply (at 5-40 min). The mechanisms responsible for the declining values for force measurements are discussed, and we make specific recommendations for obtaining valid measurements of contractile force.