Nd:YAG laser penetration into cast titanium and gold alloy with different surface preparations

This study investigated the effect of surface preparation on the Nd:YAG laser penetration into cast titanium and gold alloy. Cast blocks of each metal were given four different surface preparations: (i) coloured with black marker; (ii) air-abraded with 50 microm Al2O3; (iii) ground with SiC points and (iv) polished with 1 microm Al2O3 (mirror-polished). Two blocks with each of the surface preparations were abutted and laser-welded at their interface using the voltages of 210-260 V in increments of 10 V. After the welded blocks were mechanically separated, the laser penetration was measured using computer graphics. Regardless of the surface preparation, an increase in voltage increased the laser penetration for both metals. The laser penetration into titanium prepared with black marker and air-abrasion was significantly deeper than into the titanium ground with SiC points and mirror-polished. Although there were no statistical differences in penetration among the surface preparations for the gold alloy, the penetration in the mirror-polished specimens was shallower than any of the other preparation methods at higher voltages of 240-260 V. The results obtained in this study suggested that broken metal frameworks with finished surfaces should be painted with black marker or air-abraded before laser welding.

Penetration depth into dental casting alloys by Nd:YAG laser

This study investigated the effect of laser-beam welding conditions [voltage (V) and spot diameter (mm)] on the penetration depth into dental casting alloys. Castings (3.0 mm x 8.0 mm x 50 mm) were prepared from the metals used in this study: commercially pure titanium (CP Ti), Ti-6Al-4V, Ti-6Al-7Nb, cobalt-chromium alloy (Co-Cr) and Type IV gold alloy. Two cast blocks of each metal were butted against one another at the 8.0 x 50-mm surfaces. They were then welded at their interface under the following conditions: voltage of 160-340 V, spot diameter of 0.4-1.6 mm, and pulse duration of 10 ms. After laser welding, the blocks were separated, and the penetration depth into each alloy was measured. The data were analyzed with the use of ANOVA at the p < 0.05 level of significance. The penetration depths were as follows: CP Ti (0.29-6.45 mm), Ti-6Al-4V (0.32-5.24 mm), Ti-6Al-7Nb (0.34-5.65 mm), Co-Cr (0.24-6.15 mm), and Type IV gold alloy (0.12-5.22 mm). The voltage and spot diameter affected the penetration depth into the metals tested. When the voltage increased and the spot diameter decreased, the penetration depth increased for each metal. Selecting suitable conditions for laser welding to obtain sufficient penetration depth for the optimal thickness of the metal is important when welding prostheses.

Mechanical strength of laser-welded cobalt-chromium alloy

The purpose of this study was to investigate the effect of the output energy of laser welding and welding methods on the joint strength of cobalt-chromium (Co-Cr) alloy. Two types of cast Co-Cr plates were prepared, and transverse sections were made at the center of the plate. The cut surfaces were butted against one another, and the joints welded with a laser-welding machine at several levels of output energy with the use of two methods. The fracture force required to break specimens was determined by means of tensile testing. For the 0.5-mm-thick specimens, the force required to break the 0.5-mm laser-welded specimens at currents of 270 and 300 A was not statistically different (p > 0.05) from the results for the nonwelded control specimens. The force required to break the 1.0-mm specimens double-welded at a current of 270 A was the highest value among the 1.0-mm laser-welded specimens. The results suggested that laser welding under the appropriate conditions improved the joint strength of cobalt- chromium alloy.

Detoxification mechanism of heavy metals in marine mammals and seabirds: interaction of selenium with mercury, silver, copper, zinc, and cadmium in liver

Subcellular distribution of mercury, selenium, silver, copper, zinc, and cadmium was determined in the liver of northern fur seals (Callorhinus ursinus), black-footed albatrosses (Diomedea nigripes), and Dall's porpoises (Phocoenoides dalli). Mercury, selenium, and silver were preferentially accumulated in nuclear, lysosomal, and mitochondrial fraction with an increase in their hepatic concentrations, whereas copper, zinc, and cadmium were accumulated mainly in cytosol with an increase in the hepatic concentrations for all three species. To gain insight into the existing state of the metals, they were extracted with four extractants--sodium dodecylsulfate (SDS); 2-mercaptoethanol; 2-mercaptoethanol + guanidinium thiocyanate; and copper sulfate (CuSO4)--at several concentrations from nuclear, lysosomal, and mitochondrial fraction in liver from a specimen of northern fur seal. Extraction efficiencies of the metals for 2-mercaptoethanol + guanidinium thiocyanate and CuSO4 were much higher than those for SDS and 2-mercaptoethanol. Also, for all individuals of the three species, metals were extracted by the three extractants--2% SDS; 0.25 mol/L 2-mercaptoethanol + 5 mol/L guanidinium thiocyanate; and 0.1 mol/L CuSO4--from nuclear, lysosomal, and mitochondrial fraction of liver. In the northern fur seals with higher concentration of mercury, the molar ratio of selenium to mercury approached unity in the nonextractable fraction of 0.25 mol/L 2-mercaptoethanol + 5 mol/L guanidinium thiocyanate, suggesting the possible formation of mercuric selenide (HgSe) with increasing hepatic concentration. Because the nonextractable content of mercury and its distribution were larger for black-footed albatross than those for the other two species, it was suggested that the black-footed albatross has a stronger ability to form a stable compound(s) of mercury in the liver. It is notable that the existing state of silver was similar to that of mercury as judged by their subcellular distribution and the extraction tests, suggesting that silver also interacted with selenium in the liver of marine animals used in this study.

Isolation of Legionella pneumophila from hospital cooling towers in Johor, Malaysia

Water-based cooling towers and their water supply at two hospitals in Johor were surveyed for the presence Legionella pneumophila. L. pneumophila were grown from 19 (76%) out of 25 collected water samples. One hospital cooling tower was contaminated with L. pneumophila serogroup 1.

Effect of heat treatments on machinability of gold alloy with age-hardenability at intraoral temperature

OBJECTIVE

This study investigated the effect of heat treatment on the machinability of heat-treated cast gold alloy with age-hardenability at intraoral temperature using a handpiece engine with SiC wheels and an air-turbine handpiece with carbide burs and diamond points.

METHODS

Cast gold alloy specimens underwent various heat treatments [As-cast (AC); Solution treatment (ST); High-temperature aging (HA), Intraoral aging (IA)] before machinability testing. The machinability test was conducted at a constant machining force of 0.784N. The three circumferential speeds used for the handpiece engine were 500, 1,000 and 1,500 m/min. The machinability index (M-index) was determined as the amount of metal removed by machining (volume loss, mm(3)). The results were analyzed by ANOVA and Scheffé's test.

RESULTS

When an air-turbine handpiece was used, there was no difference in the M-index of the gold alloy among the heat treatments. The air-turbine carbide burs showed significantly (p<0.05) higher M-indexes than the diamond points after any heat treatments. With the SiC wheels, increasing the circumferential speed increased the M-index values for each heat treatment. The specimens heat-treated with AC, HA and IA had similar M-indexes at the lower speeds (500 and 1,000 m/min). The ST specimens exhibited the lowest M-index at the lower speeds. However, at the highest speed (1,500 m/min), there were no significant differences in the M-indexes among the heat treatments except for HA, which showed the highest M-index.

CONCLUSION

There was no effect of heat treatment on the machinability of the gold alloy using the air-turbine handpiece. The heat treatments had a small effect on the M-index of the gold alloy machined with a SiC wheel for a handpiece engine.

Surface treatment of dentin with GLUMA and iron compounds for bonding indirect restorations

The purpose of this study was to evaluate five dentin bonding systems simulating indirect restorations. The surface of bovine and human dentin was primed with a glutaraldehyde agent (GLUMA) and placed in a humidor at 37 degrees C for 168 h. In an experimental bonding system (GLUMA/CY/SB), the surfaces were etched with phosphoric acid, primed with cytochrome c, and then bonded to an acrylic rod with a self-curing resin (4-META/MMA-TBB). Specimens using two commercially available bonding systems [All-Bond 2 (AB2) and Super-Bond C & B (10-3/SB)] and two controls with and without GLUMA (GLUMA/10-3/SB and CY/SB) were also prepared. Tensile testing revealed that the bond strengths were influenced by the bonding system, 168 h dentin exposure and their interaction, but not by the tooth origin. AB2 showed the lowest bond strength. With the 10-3/SB system, exposing the dentin to humidity resulted in a decrease in bond strength. After 168 h of exposure, no significant differences were observed between 10-3/SB and CY/SB. The most effective bonding was obtained with the bonding systems of GLUMA/10-3/SB and GLUMA/CY/SB. Improved outcome is expected with these bonding systems when building up abutment teeth with indirect restorations.

Effect of disinfectants containing glutaraldehyde on bonding of a tri-n-butylborane initiated resin to dentine

The purpose of this study was to evaluate the effects of disinfectants on the bond strength of resin to dentine. The surface of bovine dentine was exposed to formaldehyde (FA) aqueous solutions, glutaraldehyde (GA) aqueous solutions, 2-hydroxyethyl methacrylate aqueous solutions (HEMA), a commercially available dentine primer (Gluma CPS desensitizer, GLUMA), isotonic sodium chloride solution (IS), and distilled water (DW), and placed in a humidor (HU) at 37 degrees C, or non-stored (baseline). All dentine surfaces were conditioned with a 10% citric acid and 3% ferric chloride solution (10-3 liquid), and then bonded to an acrylic rod with a self-curing adhesive resin (Super-Bond C&B). The mean tensile bond strengths determined 24 h after bonding were compared by analysis of variance (ANOVA) and Fisher's protected LSD test (n=5, P < or = 0.05). The exposure of dentine to IS, DW and HU for both 48 and 168 h resulted in a decrease in bond strength when compared with the baseline. The highest bond strengths after 168 h of exposure were obtained with 5% GA, 10% HEMA, and GLUMA, the values of which were equivalent to baseline and were significantly higher than that of FA. It is concluded that disinfectant pre-treatment with 5% GA or GLUMA stabilizes the bonding of tri-n-butylborane (TBB) initiated luting agent to bovine dentine conditioned with 10-3 liquid.

[Kwashiorkor after an exclusion diet for eczema]

BACKGROUND

Nutritional disorders observed in children with eczema may be aggravated by inappropriate diet, sometimes with dramatic effects.

CASE REPORT

A child aged 3 years 7 months presented a state of severe malnutrition with edema (kwashiorkor). The child had chronic eczema and had been given a highly restrictive diet based on a principle of exclusion without medical advise. Cure was achieved without sequelae with a normal diet.

DISCUSSION

This case illustrates the fragility of nutritional status in children with chronic widespread skin disease due to the risk of cutaneous loss of protein. Kwashiorkor is an exceptional observation in developed countries and, in this context, might be on the rise due to the popularity of exclusion diets for presumed allergic disease.

Nulling interferometry by use of geometric phase

Nulling interferometry is a method of detecting a faint source near a bright one, in which destructive interference is realized for the light from the bright source. A nulling interferometer that makes use of geometric phase (Pancharatnam phase) is proposed. An experimental setup is constructed to simulate a stellar interferometer with geometric-phase modulation. We attained extinction of 6 x 10(-5) in white light.

An auto-tuning method for focusing and astigmatism correction in HAADF-STEM, based on the image contrast transfer function

An auto-tuning method for high-angle annular detector dark field scanning transmission electron microscopy (HAADF-STEM) is proposed which corrects the defocus to the optimum Scherzer focus and compensates the astigmatism. Because the method is based on the image contrast transfer function formulated for the HAADF-STEM, the defocus and the astigmatism are accurately measured from input of two different defocus images. The method is designed to work independent of object function in the linear imaging model by analysing the spectral ratio between two Fourier spectra of their images, which is useful for cases where the spectrum of object function is not uniformly spread out over the reciprocal space. The method was preliminarily tested in a Hitachi HD-2000 STEM, and successful results of the auto-tunings from the viewpoint of verification of the algorithm were obtained using general specimens of Au fine particles and a thin section of a semiconductor device.

Effects of tomato juice consumption on plasma and lipoprotein carotenoid concentrations and the susceptibility of low density lipoprotein to oxidative modification

Effects of tomato juice supplementation on the carotenoid concentration in lipoprotein fractions and the oxidative susceptibility of LDL were investigated in 31 healthy Japanese female students. These subjects were randomized to one of three treatment groups; Control, Low and High. The Control, Low and High groups consumed 480 g of a control drink, 160 g of tomato juice plus 320 g of the control drink, and 480 g of tomato juice, providing 0, 15 and 45 mg of lycopene, respectively, for one menstrual cycle. The ingestion of tomato juice, rich in lycopene but having little beta-carotene, increased both lycopene and beta-carotene. Sixty-nine percent of lycopene in plasma was distributed in the LDL fraction and 24% in the HDL fraction. In the Low group, the lycopene concentration increased 160% each in the VLDL+IDL, LDL and HDL fractions (p<0.01). In the High group, the lycopene concentration increased 270% each in the VLDL+IDL and LDL fractions, and 330% in the HDL fraction (p<0.01). Beta-carotene also increased 120% and 180% in LDL fractions of the Low and the High groups, respectively. Despite these carotenoid increases in LDL, the lag time before oxidation was not prolonged as compared with that of the Control group. The propagation rate decreased significantly after consumption in the High group. Multiple regression analysis showed a positive correlation between lag time changes and changes in the alpha-tocopherol concentration per triglyceride in LDL, and a negative correlation between propagation rate changes and changes in the lycopene concentration per phospholipid in LDL. These data suggest that alpha-tocopherol is a major determinant in protecting LDL from oxidation, while lycopene from tomato juice supplementaion may contribute to protect phospholipid in LDI, from oxidation. Thus, oral intake of lycopene might be beneficial for ameliorating atherosclerosis.

Cytotoxicity of reactive oxygen species and related agents toward undifferentiated and differentiated rat phenochromocytoma PC12 cells

The cytotoxicity of reactive oxygen species and related agents toward cultured rat adrenal medullary phenochromocytoma PC12 cells was examined. These species and agents include hydrogen peroxide, linoleic acid hydroperoxide (LOOH), tert-butyl hydroperoxide, paraquat, 2,2'-azobis(2-amidinopropane) dihydrochloride (AAPH), 2,2'-azobis(2,4-dimethylvaleronitrile) (AMVN), and a hypoxanthine-xanthine oxidase system. The respective 50% lethal concentrations (LC50) for undifferentiated and differentiated PC12 cells were found to be 275 and 165 microM of hydrogen peroxide, 58.3 and 35.3 microM of LOOH, 536 and 212 microM of tert-butyl hydroperoxide, 42.5 and 26.5 mM of paraquat, 79.5 and 74.5 mM of AAPH, 412 and 300 microM of AMVN, and 37.2 and 16.6mU x ml(-1) xanthine oxidase activity of the hypoxanthine-xanthine oxidase system. These results show that the differentiated cells were more susceptible to these oxidative agents than the undifferentiated cells. The glutathione peroxidase activity level of the undifferentiated cells was 2-3 times higher than the differentiated cells, the catalase activity level also tended to be higher, the superoxide dismutase activity level was higher on a per-protein-quantity basis but lower on a per-cell-number basis, and the total and reduced glutathione concentration levels were considerably higher. The enhanced susceptibility of the differentiated cells may result from decreases in the activity of glutathione peroxidase and the concentration of its substrate, reduced glutathione (GSH). Further, the preincubation of PC12 cells with alpha-tocopherol or L-buthionine-(R,S)-sulfoximine (BSO) lowered or enhanced their cytotoxicities, respectively.

[Cutaneous blastomycosis revealing a corticoadenoma]

BACKGROUND

Blastomycosis is an uncommon chronic granulomatosis caused by Blastomyces dermatitidis. We present a case with a skin localization that disclosed malignant corticoadenoma.

CASE REPORT

A 32-year-old man consulted for inflammatory nodules of the face and lower limbs. The histological examination of a nodule biopsy was in favour of blastomycosis. Ketoconazole treatment was ineffective. Amphotericin B provided cure of the skin lesions. Search for extension disclosed a malignant corticoadrenoma.

DISCUSSION

Blastomycosis is very rare in Morocco. The portal is usually the lung. Unique skin involvement is very exceptional. To our knowledge this is the first report of a blastomycosis-corticoadenoma association. The clinical situation may be alarming in immunodepressed subjects. Amphotericin B treatment is indicated.

Measurement of telescope aberrations through atmospheric turbulence by use of phase diversity

We conduct computer simulations of the reconstruction of a wave front at a telescope pupil with the phase-diversity method. An instantaneous wave front is reconstructed from focused and defocused specklegrams of a point star. In the wave-front reconstruction we do not fit the wave front to Zernike polynomials but retrieve the phase with a phase-unwrapping procedure. Averaging over many atmospherically perturbed wave fronts leads to the residual phase error, namely, the aberration of the telescope. The scintillation effect, nonuniformity of amplitude on a telescope pupil, is also discussed.

Accumulation of silver in the liver of three species of pinnipeds

Silver in the three species of pinnipeds [northern fur seal (Callorhinus ursinus), Steller sea lion (Eumetopias jubatus), and harbor seal (Phoca vitulina)] caught in the North Pacific Ocean were analyzed using inductively coupled plasma-mass spectrometry, in order to understand accumulation and distribution of silver in pinnipeds. In northern fur seals, relatively high concentrations of silver were observed in the liver and body hair. Some 70% of the silver burden was concentrated in the liver. Hepatic silver concentrations were significantly correlated to age in northern fur seals (r = 0.766, P < 0.001, n = 49) and Steller sea lions (r = 0.496, P < 0.01, n = 28). Levels of silver concentrations per wet weight (microgram g-1) in the three pinnipeds ranged from 0.04 to 0.55 for northern fur seals, from 0.1 to 1.04 for Steller sea lions and from 0.03 to 0.83 for harbor seals. Silver concentrations in liver for all pinnipeds were significantly correlated with mercury, and selenium (P < 0.001). Molar ratios between silver to selenium approximated 1:180 in northern fur seals, 1:120 in Steller sea lions, and 1:60 in harbor seals. The silver-mercury molar ratios were approximately 1:170 in northern fur seals, and 1:80 both in the other species. Increase in silver accumulation in the liver was caused by the retention in nuclei and mitochondria fraction together with mercury and selenium in the cells of northern fur seals.

Synthesis of a novel lysophosphatidylcholine

The novel lysophosphatidylcholine (1), which naturally occurs in the marine sponge Spirastrella abata and was reported to inhibit cholesterol biosynthesis in the Chang liver cell, has been synthesized in four steps from methyl cis-11-octadecenoate (2).

Molecular cloning of the gene encoding an outer-membrane-associated beta-N-acetylglucosaminidase involved in chitin degradation system of Alteromonas sp. strain O-7

The gene encoding beta-N-acetylglucosaminidase (GlcNAcaseA) was cloned using PCR with degenerate oligonucleotide primers from the partial amino acid sequence of the enzyme. The gene encoded a polypeptide of 863 amino acids with a predicted molecular mass of 97kDa. A characteristic signal peptide, which was present at the amino-terminus of the precursor protein, contained four amino acids (Ala-Gly-Cys-Ser) identical in sequence and location to the processing and modification sites of the outer membrane lipoprotein of Escherichia coli, indicating that the mature GlcNAcaseA is a lipoprotein the N-terminal cysteine residue of which would be modified by the fatty acid that anchors the protein in the membrane. The predicted amino acid sequence of GlcNAcaseA showed similarity to bacterial beta-N-acetylglucosaminidases belonging to the family 20 glycosyl hydrolases.

Prevention of death of axotomized hypoglossal neurones and promotion of regeneration by chitin grafting

1. Chitin is known to promote skin wound healing. In this study, chitin, prepared from Zuwai crab shell, was used as a bridge between the proximal and distal stumps of cut hypoglossal nerves in shrews. We compared the effects of chitin on the regeneration of transected right hypoglossal nerve axons, with those of porcine dermis, bovine dermal aterocollagen, and autologous nerve bundles. 2. To assess the survival of neurones, the size of neuronal cell body, and number of motoneurones were determined in the absence of any bridged material and in the presence of porcine dermis, bovine dermal aterocollagen, chitin, or autologous nerve bundles as a bridge. 3. Our results revealed a significantly better outcome in chitin and autologous nerve bridged groups; the size of neuronal cell body and number of hypoglossal neurones were higher than in the other groups. Chitin also enhanced the regeneration of neurones; the number of horseradish peroxide positive neurones indicative of repaired axonal processes was significantly higher in chitin and autologous nerve-bridged groups than in other groups. 4. Our results demonstrated that the use of chitin sheet or autograft successfully prevented the death of severed neurones and promoted the regeneration of the lesioned nerve. Although the mechanisms underlying the effects of chitin are still unknown, chitin seems to be a potentially useful biocompatible material for nerve repair and regeneration.

Enhancement of rat hypoglossal nerve regeneration by chitin sheet plus gangliosides

The effects of chitin sheet interposition with and without brain gangliosides on the regeneration of hypoglossal nerve fibres was studied in the rat following resection of a 5mm length of the nerve. At 10 weeks after operation, the number of horseradish peroxidase (HRP)-labelled motor neurones, indicative of the axonal repair process, on the side treated with chitin and gangliosides was higher than on the control side (where 5mm of the nerve was simply resected). The ratios of HRP-positive neurones in the right hypoglossal nucleus (treated side)/left hypoglossal nucleus (intact side) was 0 in the 5mm-resected group, 53% in the chitin-grafted group, 88% in the ganglioside (0.2 microg)-injected group, 90% in the ganglioside (2 microg)-injected group, 91% in the chitin with ganglioside (0.2mg)-injected group, 91% in the chitin with ganglioside (2 microg)-injected group and 85% in the autograft group, respectively. There were significant differences between the 5 mm-resected group and chitin-grafted group, ganglioside-injected group, chitin with ganglioside group and autograft group, and between the chitin-grafted group and ganglioside-injected, chitin with ganglioside and autograft groups (P< 0.005, respectively). Our results indicated that the use of chitin and gangliosides stimulated the regeneration of severed motor nerve fibres. These findings suggest that chitin and gangliosides might be therapeutically useful for treatment of neuronal degeneration.