Needle insertion into soft tissue: a survey

Extended Kalman filter for online soft tissue characterization based on Hunt-Crossley contact model

Real-time soft tissue characterization is significant to robotic assisted minimally invasive surgery for achieving precise haptic control of robotic surgical tasks and providing realistic force feedback to the operator. This paper presents a nonlinear methodology for online soft tissue characterization. An extended Kalman filter (EKF) is developed based on dynamic linearization of the nonlinear H-C contact model in terms of system state for online characterization of soft tissue parameters. To handle the resultant linearization modelling error, an innovation orthogonal EKF is further developed by incorporating an adaptive factor in the EKF filtering to adaptively adjust the innovation covariance according to the principle of innovation orthogonality. Simulation and experimental results as well as comparison analysis demonstrate that the proposed methodology can effectively characterize soft tissue parameters, leading to dramatically improved accuracy comparing to recursive least square estimation. Further, the proposed methodology also requires a smaller computational load and can achieve the real-time performance for soft tissue characterization.

Computer-Assisted Detection of Cemento-Enamel Junction in Intraoral Ultrasonographs

The cemento-enamel junction (CEJ) is an important reference point for various clinical measurements in oral health assessment. Identifying CEJ in ultrasound images is a challenging task for dentists. In this study, a computer-assisted detection method is proposed to identify the CEJ in ultrasound images, based on the curvature change of the junction outlining the upper edge of the enamel and cementum at the cementum–enamel intersection. The technique consists of image preprocessing steps for image enhancement, segmentation, and edge detection to locate the boundary of the enamel and cementum. The effects of the image preprocessing and the sizes of the bounding boxes enclosing the CEJ were studied. For validation, the algorithm was applied to 120 images acquired from human volunteers. The mean difference of the best performance between the proposed method and the two raters’ measurements was an average of 0.25 mm with reliability ≥ 0.98. The proposed method has the potential to assist dental professionals in CEJ identification on ultrasonographs to provide better patient care.

On the flexible needle insertion into the human liver

In the present research, the navigation of a flexible needle into the human liver in the context of the robotic-assisted intraoperative treatment of the liver tumors, is reported. Cosserat (micropolar) elasticity is applied to describe the interaction between the needle and the human liver. The theory incorporates the local rotation of points and the couple stress (a torque per unit area) as well as the force stress (force per unit area) representing the chiral features of the human liver. To predict the deformation of the needle and the liver, the elastic properties of the human liver have been evaluated. Outcomes reveal that considering smaller deformations of the needle and the liver results in better needle navigation mechanism. The needle geometry can enhance the penetration.

Multi-Bevel Needle Design Enabling Accurate Insertion in Biopsy for Cancer Diagnosis

OBJECTIVE

To obtain definitive cancer diagnosis for suspicious lesions, accurate needle deployment and adequate tissue sampling in needle biopsy are essential. However, the single-bevel needles in current biopsy devices often induce deflection during insertion, potentially causing lesion missampling/undersampling and cancer misdiagnosis. This study aims to reveal the biopsy needle design criteria enabling both low deflection and adequate tissue sampling.

METHODS

A novel model capable of predicting needle deflection and tissue deformation was first established to understand needle-tissue interaction with different needle tip geometries. Experiments of needle deflection and ex-vivo tissue biopsy were conducted for model validation.

RESULTS

The developed model showed a reasonably good prediction on the correlation of needle tip type vs. the resultant needle deflection and tissue sampling length. A new multi-bevel needle with the tissue separation point below the needle groove face has demonstrated to be an effective design with an 87% reduction in deflection magnitude and equivalently long tissue sampling length compared to the current single-bevel needle.

CONCLUSION

This study has revealed two critical design criteria for biopsy needles: 1) multiple bevel faces at the needle tip can generate forces to balance bending moments during insertion to enable a low needle deflection and 2) the tissue separation point should be below the needle groove face to ensure long tissue sampling length.

SIGNIFICANCE

The developed methodologies and findings in this study serve as proof-of-concept and can be utilized to investigate various biopsy procedures to improve cancer diagnostic accuracy as well as other procedures requiring accurate needle insertion.

Design Considerations for a Steerable Needle Robot to Maximize Reachable Lung Volume

Steerable needles that are able to follow curvilinear trajectories and steer around anatomical obstacles are a promising solution for many interventional procedures. In the lung, these needles can be deployed from the tip of a conventional bronchoscope to reach lung lesions for diagnosis. The reach of such a device depends on several design parameters including the bronchoscope diameter, the angle of the piercing device relative to the medial axis of the airway, and the needle's minimum radius of curvature while steering. Assessing the effect of these parameters on the overall system's clinical utility is important in informing future design choices and understanding the capabilities and limitations of the system. In this paper, we analyze the effect of various settings for these three robot parameters on the percentage of the lung that the robot can reach. We combine Monte Carlo random sampling of piercing configurations with a Rapidly-exploring Random Trees based steerable needle motion planner in simulated human lung environments to asymptotically accurately estimate the volume of sites in the lung reachable by the robot. We highlight the importance of each parameter on the overall system's reachable workspace in an effort to motivate future device innovation and highlight design trade-offs.

Path Replanning for Orientation-Constrained Needle Steering

INTRODUCTION

Needle-based neurosurgical procedures require high accuracy in catheter positioning to achieve high clinical efficacy. Significant challenges for achieving accurate targeting are (i) tissue deformation (ii) clinical obstacles along the insertion path (iii) catheter control.

OBJECTIVE

We propose a novel path-replanner able to generate an obstacle-free and curvature bounded three-dimensional (3D) path at each time step during insertion, accounting for a constrained target pose and intraoperative anatomical deformation. Additionally, our solution is sufficiently fast to be used in a closed-loop system: needle tip tracking via electromagnetic sensors is used by the path-replanner to automatically guide the programmable bevel-tip needle (PBN) while surgical constraints on sensitive structures avoidance are met.

METHODS

The generated path is achieved by combining the "Bubble Bending" method for online path deformation and a 3D extension of a convex optimisation method for path smoothing.

RESULTS

Simulation results performed on a realistic dataset show that our replanning method can guide a PBN with bounded curvature to a predefined target pose with an average targeting error of 0.65  ± 0.46 mm in position and 3.25  ± 5.23 degrees in orientation under a deformable simulated environment. The proposed algorithm was also assessed in-vitro on a brain-like gelatin phantom, achieving a target error of 1.81  ± 0.51 mm in position and 5.9  ± 1.42 degrees in orientation.

CONCLUSION

The presented work assessed the performance of a new online steerable needle path-planner able to avoid anatomical obstacles while optimizing surgical criteria.

SIGNIFICANCE

This method is particularly suited for surgical procedures demanding high accuracy on the desired goal pose under tissue deformations and real-world inaccuracies.

Needle insertion-induced quasiperiodic cone cracks in hydrogel

Needle insertion, a standard process for various minimally invasive surgeries, results in tissue damage which sometimes leads to catastrophic outcomes. Opaqueness and inhomogeneity of the tissues make it difficult to observe the underlying damage mechanisms. In this paper, we use transparent and homogeneous polyacrylamide hydrogel as a tissue mimic to investigate the damages caused during needle insertion. The insertion force shows multiple events, characterised by a gradual increase in the force followed by a sharp fall. Synchronised recording of the needle displacement into the gel shows that each event corresponds to propagation of stable cone crack. Though sporadic uncontrolled cracking has been discussed earlier, this is the first report of nearly periodic, stable and well-controlled 3-D cone cracks inside the hydrogel during deep penetration. We show that the stress field around the needle tip is responsible for the symmetry and periodicity of the cone cracks. These results provide a better understanding of the fracture processes in soft and brittle materials and open a promising perspective in needle designs and the control of tissue damages during surgical operations.

A novel manipulator with needle insertion forces feedback for robot-assisted lumbar puncture

BACKGROUND

The use of lumbar puncture for paediatric diagnosis and treatment, such as cerebrospinal fluid sampling and intracranial pressure measurements, is steadily increasing. However, the standard 'blind' technique makes it difficult to attain accurate needle insertion.

METHODS

In this study, we developed a robot-assisted system to improve the precision of needle insertion during lumbar puncture. The manipulator can perform orientation, insertion and rotation of the needle as well as linear motion at targeted locations. We focused on accurately sensing the puncture forces during the needle insertion phase and evaluated the piercing force perception of the operator.

RESULTS

The main features of the robot, such as backdrivable joints, physical human-robot cooperation, actuation system with low friction and remote centre of motion mechanism, can enhance overall safety.

CONCLUSIONS

Experimental results using a lumbar puncture phantom proved that the manipulator could position the needle tip at targeted locations with good accuracy. The data obtained from the test system also showed that the loss of resistance and peak forces for stiff tissues were accurately perceived by the operator.

Design, Fabrication, and Testing of a Flexible Three-Dimensional Printed Percutaneous Needle With Embedded Actuators

Percutaneous needle-based procedures have replaced open surgeries in cancer treatments to perform the tasks with minimal invasiveness to the tissue. Precise placement of the needle at target positions in cancer diagnostic (e.g., breast biopsy) or therapeutic (e.g., prostate brachytherapy) procedures governs the success of such procedures. Also, in many needle insertion applications, it is desired to steer away from critical organs or to maneuver around anatomical obstacles in tissue. This work introduces a flexible three-dimensional (3D) printed percutaneous needle with embedded actuators for improved navigation inside the tissue toward the target. The needle is manipulated via a programmed portable motorized control unit to realize an average angular deflection of about 15 and 14 deg in air and a tissue-mimicking phantom, respectively. We demonstrated the needle's capability to reach the target, while avoiding obstacles. We also demonstrated that the flexible needle can be guided through a desired trajectory by controlling its angular deflection and axial movement. The 3D deflection of the needle is expected to assist in breast cancer lumpectomy for multiple extractions of tissue samples or in prostate brachytherapy via a curvilinear approach. The flexible needle may help reducing the complexity of current path planning algorithms, and thereby improve efficiency of closed-loop control systems in needle steering.

Surgical planning assistance in keyhole and percutaneous surgery: A systematic review

Surgical planning of percutaneous interventions has a crucial role to guarantee the success of minimally invasive surgeries. In the last decades, many methods have been proposed to reduce clinician work load related to the planning phase and to augment the information used in the definition of the optimal trajectory. In this survey, we include 113 articles related to computer assisted planning (CAP) methods and validations obtained from a systematic search on three databases. First, a general formulation of the problem is presented, independently from the surgical field involved, and the key steps involved in the development of a CAP solution are detailed. Secondly, we categorized the articles based on the main surgical applications, which have been object of study and we categorize them based on the type of assistance provided to the end-user.

Mathematical modeling and computer simulation of needle insertion into soft tissue

In this study we present a kinematic approach for modeling needle insertion into soft tissues. The kinematic approach allows the presentation of the problem as Dirichlet-type (i.e. driven by enforced motion of boundaries) and therefore weakly sensitive to unknown properties of the tissues and needle-tissue interaction. The parameters used in the kinematic approach are straightforward to determine from images. Our method uses Meshless Total Lagrangian Explicit Dynamics (MTLED) method to compute soft tissue deformations. The proposed scheme was validated against experiments of needle insertion into silicone gel samples. We also present a simulation of needle insertion into the brain demonstrating the method's insensitivity to assumed mechanical properties of tissue.

Localization Accuracy of Ultrasound-Actuated Needle with Color Doppler Imaging

An ultrasonic needle-actuating device for tissue biopsy and regional anaesthesia offers enhanced needle visibility with color Doppler imaging. However, its specific performance is not yet fully determined. This work investigated the influence on needle visibility of the insertion angle and drive voltage, as well as determined the accuracy and agreement of needle tip localization by comparing color Doppler measurements with paired photographic and B-mode ultrasound measurements. Needle tip accuracy measurements in a gelatin phantom gave a regression trend, where the slope of trend is 0.8808; coefficient of determination (R²) is 0.8877; bias is −0.50 mm; and the 95% limits of agreement are from −1.31 to 0.31 mm when comparing color Doppler with photographic measurements. When comparing the color Doppler with B-mode ultrasound measurements, the slope of the regression trend is 1.0179; R² is 0.9651; bias is −0.16 mm; and the 95% limits of agreement are from −1.935 to 1.605 mm. The results demonstrate the accuracy of this technique and its potential for application to biopsy and ultrasound guided regional anaesthesia.

Preliminary study on mechanical characteristics of maxillofacial soft and hard tissues for virtual surgery

Purpose

Virtual surgery system can provide us a realistic and immersive training environment, in which haptic force-feedback gives operators ‘touching feeling.’ Appropriate deformation models of soft and hard tissues are required for the achievement of real-time haptic feedback. To improve accuracy of modeling and haptic feedback simulation for maxillofacial virtual surgery, mechanical characteristics of soft and hard tissues should be explored.

Methods

Craniofacial soft tissues from one male and female cadavers were divided into two layers: skin and muscle. Maxillofacial tissues were divided into frontal, chin, temporalis, masseter regions. Insertion and cutting process were conducted using VMX42 5-axis linkage system and recorded by piezoelectric dynamometer. Maximum stiffness values were analyzed, and insertion curves before puncture were fitted using a polynomial model. Elasticity modulus and hardness of maxillofacial hard tissues were measured and analyzed using Berkovich nanoindentation.

Results

Tissues in different maxillofacial regions, as well as from different layers (skin and muscle), displayed various mechanical performance. Maximum stiffness values and cutting force of soft tissues in male and female had significant difference. The third-order polynomial was demonstrated to fit the insertion curves well before puncture. Furthermore, elasticity modulus and hardness of enamel were significantly greater than that of zygoma, maxilla and mandible.

Conclusion

Mechanical properties of hard tissues are relatively stable, which can be applied in virtual surgery system for physical model construction. Insertion model and cutting force for soft tissues are meaningful and applicable and can be utilized to promote the accuracy of response for haptic feedback sensations.

Development of haptic simulator for practicing the intraarticular needle injection under echography

Intraarticular needle injection under ultrasound guidance is the most used method to provide pain relief in joints. To learn this process, medical students need to practice in order to master the manipulation of the syringe and the ultrasound probe at the same time. To offer a risk-free training for trainees, we present in this paper the development and design of a haptic simulator prototype. The models and methods used to render the forces involved are introduced, as well as the mechanical design and finally a validation test performed by our medical partner.Clinical relevance-This simulator helps medical students to train intraarticular needle injection under ultrasound guidance using a haptic device to provide realism and immersion.

Design and Applicability of a Mechanical Impedance Sensor for Vein Penetration Detection

Intravenous needle insertion is typically conducted manually, with needles guided into vessels by feel while looking for a brief flash of blood. This process is imprecise and leads to mispositioned needles, multiple reinsertion attempts, increased procedure time and higher costs for the hospital. We present a method for indicating that the needle has reached the vein by measuring the change in mechanical impedance of the needle as it passes through different tissue layers. Testing in a phantom indicated that this has the potential to identify transitions through tissue boundaries.

Decoupling Steerability from Diameter: Helical Dovetail Laser Patterning for Steerable Needles

The maximum curvature of a steerable needle in soft tissue is highly sensitive to needle shaft stiffness, which has motivated use of small diameter needles in the past. However, desired needle payloads constrain minimum shaft diameters, and shearing along the needle shaft can occur at small diameters and high curvatures. We provide a new way to adjust needle shaft stiffness (thereby enhancing maximum curvature, i.e. "steerability") at diameters selected based on needle payload requirements. We propose helical dovetail laser patterning to increase needle steerability without reducing shaft diameter. Experiments in phantoms and ex vivo animal muscle, brain, liver, and inflated lung tissues demonstrate high steerability in soft tissues. These experiments use needle diameters suitable for various clinical scenarios, and which have been previously limited by steering challenges without helical dovetail patterning. We show that steerable needle targeting remains accurate with established controllers and demonstrate interventional payload delivery (brachytherapy seeds and radiofrequency ablation) through the needle. Helical dovetail patterning decouples steerability from diameter in needle design. It enables diameter to be selected based on clinical requirements rather than being carefully tuned to tissue properties. These results pave the way for new sensors and interventional tools to be integrated into high-curvature steerable needles.

Mechanical characterization of a fiberoptic microneedle device for controlled delivery of fluids and photothermal excitation

Current clinical approaches for treating pancreatic cancer have been demonstrated as ineffective at improving midterm survival. A primary obstacle to local drug delivery is the desmoplastic nature of the peritumoral environment, which acts as a significant barrier to circulating macromolecules. To address this need, our group presents a sharp fiberoptic microcatheter capable of accessing the pancreas through transduodenal endoscope and penetrating a tumor to locally co-deliver photothermal and fluid-based therapies. Experiments sought to characterize the mechanical penetration capabilities and fluid mechanics of the fiberoptic microneedle design. A refined off-center fusion splicing technique was developed for joining a multimode fiber to the annular core of a light-guiding capillary, allowing light transmission with minimal optical loss. A novel and frugal technique for assessing the penetration force of the microneedle was conducted in a bovine gelatin tissue phantom with a Young's modulus stiffer than the high range for pancratic tissue or tumor. Buckling forces for different microneedle lengths were measured and compared against theoretical values obtained from Euler's Critical Load equation under fixed-pinned column conditions. Hydraulic resistance of different capillary lengths was evaluated and compared against the theoretical values from Hagen-Poiseuille's law, allowing assessment of contributions from different segments of the device. The results demonstrated that the microcatheter can robustly and repeatably penetrate a soft tissue phantom chosen to be a conservative model of pancreatic tissue for penetration properties. Experiments showed that a 1.5 N insertion force was required for phantom penetration with a 45° beveled needle at a 5 mm unsupported length, while the critical buckling load was measured to be approximately 4 N. In addition, the design was demonstrated to efficiently transport 1064 nm light and aqueous fluids with a 70-75% light coupling efficiency and 12,200 Pa.s/μl hydraulic resistance, respectively. These findings motivate the FMD's further development as a treatment platform for pancreatic cancer.

Gels, jets, mosquitoes, and magnets: a review of implantation strategies for soft neural probes

Implantable neuroelectronic interfaces have enabled breakthrough advances in the clinical diagnosis and treatment of neurological disorders, as well as in fundamental studies of brain function, behavior, and disease. Intracranial electroencephalography (EEG) mapping with stereo-EEG (sEEG) depth electrodes is routinely adopted for precise epilepsy diagnostics and surgical treatment, while deep brain stimulation has become the standard of care for managing movement disorders. Intracortical microelectrode arrays for high-fidelity recordings of neural spiking activity have led to impressive demonstrations of the power of brain-machine interfaces for motor and sensory functional recovery. Yet, despite the rapid pace of technology development, the issue of establishing a safe, long-term, stable, and functional interface between neuroelectronic devices and the host brain tissue still remains largely unresolved. A body of work spanning at least the last 15 years suggests that safe, chronic integration between invasive electrodes and the brain requires a close match between the mechanical properties of man-made components and the neural tissue. In other words, the next generation of invasive electrodes should be soft and compliant, without sacrificing biological and chemical stability. Soft neuroelectronic interfaces, however, pose a new and significant surgical challenge: bending and buckling during implantation that can preclude accurate and safe device placement. In this topical review, we describe the next generation of soft electrodes and the surgical implantation methods for safe and precise insertion into brain structures. We provide an overview of the most recent innovations in the field of insertion strategies for flexible neural electrodes such as dissolvable or biodegradable carriers, microactuators, biologically-inspired support structures, and electromagnetic drives. In our analysis, we also highlight approaches developed in different fields, such as robotic surgery, which could be potentially adapted and translated to the insertion of flexible neural probes.

Experimental study of the optimum puncture pattern of robot-assisted needle insertion into hyperelastic materials

The robot-assisted insertion surgery plays a crucial role in biopsy and therapy. This study focuses on determining the optimum puncture pattern for robot-assisted insertion, aiming at the matching problem of needle insertion parameters, thereby to reduce the pain for patients and to improve the reachability to the lesion point. First, a 6-degrees of freedom (DOFs) Computed Tomography (CT)-guided surgical robotic system for minimally invasive percutaneous lung is developed and used to perform puncture experiments. The effects of four main insertion factors on the robotic puncture are verified by designing the orthogonal test, where the inserting object is the artificial skin-like specimen with high transparent property and a digital image processing method is used to analyze the needle tip deflection. Next, the various phases of puncture process are divided and analyzed in detail in view of the tissue deformation and puncture force. Then, short discussion on the comparison of puncture force with different effect factors for the same beveled needle is presented. The same pattern can be observed for all of the cases. Finally, based on the experimental data, the formulations of the puncture force and needle deflection which depends on Gauge size, insertion velocity, insertion angle, and insertion depth are developed using the multiple regression method, which can be used to get an optimum puncture pattern under the constrains of minimum peak force and minimum needle tip deflection. The developed models have the effectiveness and applicability on determining the optimum puncture pattern for one puncture event, and which can also provide insights useful for the setting of insertion parameters in clinical practice.

Fine needle insertion method for minimising deflection in lower abdomen: In vivo evaluation

BACKGROUND

Fine needle insertion in the lower abdomen is difficult because of complex deflections and few image feedbacks. We aim to develop an approach for generating a straight insertion path by minimizing the needle deflection robustly based on a preoperative computer tomography (CT) image.

METHOD

This study presents two approaches: an insertion control strategy that performs both vibration and rotation-assisted needle insertions and a preoperative insertion path planning for determining an optimal insertion path based on insertion angles at each tissue boundary. Those proposed approaches were evaluated through an in vivo experiment with a Landrace mini-pig. We compered the following: (1) the deflection with and without the insertion control strategy in different 10 insertion paths and (2) the score calculated by the path planning and the actual deflection in the 10 insertion paths.

RESULTS

The result shows that the deflection can be reduced significantly by applying the insertion control strategy in the optimal insertion path calculated by the path planning.

CONCLUSION

The proposed method can decrease fine needle deflections in the lower abdomen, which has the potential for accurate and safety procedures without real-time CT imaging.

Transjugular Intrahepatic Portosystemic Shunt Creation Using a Radiofrequency Wire: Prospective Clinical Safety and Feasibility Trial in Cirrhosis

PURPOSE

To assess the safety and feasibility of using a radiofrequency (RF) wire for portosystemic shunt creation.

MATERIALS AND METHODS

Ten patients undergoing elective creation of a transjugular intrahepatic portosystemic shunt (TIPS) or a direct intrahepatic portosystemic shunt (DIPS) were prospectively enrolled. Primary outcomes were the safety and feasibility of RF wire used for the creation of TIPS and DIPS. Median age was 66.5 ± 6.1 years. Causes of liver disease included alcohol (n = 5), nonalcoholic steatohepatitis (n = 2), hepatitis C virus (n = 1), primary biliary cirrhosis (n = 1), autoimmune hepatitis (n = 1). The median score for model for end-stage liver disease was 11 ± 4.3. The Rosch-Uchida TIPS set was used with intravascular ultrasonography guidance in all cases. A 0.035-inch RF wire was used in lieu of the trocar needle through the 5-F TIPS set catheter to create a track between the hepatic vein and the portal vein. All shunts were created using stent grafts.

RESULTS

Technical success rate was 100%. In 7 of 10 patients, portal vein access was achieved with a single pass. A DIPS was created in 2 patients based on anatomic favorability. Median fluoroscopy time was 13.3 ± 3.8 min, and median total procedure time was 102 ± 19 min. The wire passed through parenchyma without subjective deflection. There was 1 case of extracapsular puncture with no clinical consequence. The RF wire was too stiff to curve into the main portal vein, requiring wire exchange in all but 1 case. Mean portosystemic gradient decreased from 13.9 ± 3.3 to 5.9 ± 2.1 mm Hg. No immediate complications were encountered. Shunt patency was 100% at 30 days.

CONCLUSIONS

Creation of TIPS and DIPS using an RF wire was safe and feasible, enabling creation of an intrahepatic track without subjective deflection in cirrhotic patients.

Bevel angle study of flexible hollow needle insertion into biological mimetic soft-gel: Simulation and experimental validation

BACKGROUND

A thorough understanding of cutting-edge geometry and cutting forces of hollow biopsy needles are required to optimise needle tip design to improve fine needle aspiration procedures.

OBJECTIVES

To incorporate the dynamics of needle motion in a model for flexible hollow bevel tipped needle insertion into a biological mimetic soft-gel using parameters obtained from experimental work. Additionally, the models will be verified against corresponding needle insertion experiments.

METHODS

To verify simulation results, needle deflection and insertion forces were compared with corresponding experimental results acquired with an in-house developed needle insertion mechanical system. Additionally, contact stress distribution on needles from agar gel for various time scales were also studied.

RESULTS

For the 15°, 30°, 45°, 60° bevel angle needles, and 90° blunt needle, the percentage error in needle deflection of each needle compared to experiments, were 7.3%, 9.9%, 8.6%, 7.8%, and 9.7% respectively. Varying the bevel angle at the needle tip demonstrates that the needle with a lower bevel angle produces the largest deflection, although the insertion force does not vary too much among the tested bevel angles.

CONCLUSION

This experimentally verified computer-based simulation model could be used as an alternative tool for better understanding the needle-tissue interaction to optimise needle tip design towards improved biopsy efficiency.

Passive needle guide tracking with radial acquisition and phase-only cross-correlation

PURPOSE

Acceleration of a passive tracking sequence based on phase-only cross-correlation (POCC) using radial undersampling.

METHODS

The phase-only cross-correlation (POCC) algorithm allows passive tracking of interventional instruments in real-time. In a POCC sequence, two cross-sectional images of a needle guide with a positive MR contrast are continuously acquired from which the instrument trajectory is calculated. Conventional Cartesian imaging for tracking is very time consuming; here, a higher temporal resolution is achieved using a highly undersampled radial acquisition together with a modified POCC algorithm that incorporates the point-spread-function. Targeting and needle insertion is performed in two phantom experiments with 16 fiducial targets, each using 4 and 16 radial projections for passive tracking. Additionally, targeting of eight deep lying basivertebral veins in the lumbar spines is performed for in vivo proof-of-application with four radial projections for needle guide tracking.

RESULTS

The radially undersampled POCC sequence yielded in the phantom experiments a lateral targeting accuracy of 1.1 ± 0.4 mm and 1.0 ± 0.5 mm for 16 and 4 radial projections, respectively, without any statistically significant difference. In the in vivo application, a mean targeting duration of 62 ± 13 s was measured.

CONCLUSION

Radial undersampling can drastically reduce the acquisition time for passive tracking in a POCC sequences for MR-guided needle interventions without compromising the targeting accuracy.

Compact 3D-Printed Active Flexible Needle for Percutaneous Procedures

Needle-based intervention has been a popular procedure for diagnosis and treatment of many types of cancer. However, poor needle placement and tumor visualization have been among the challenges resulting in poor clinical outcomes. There has been a lot of progress in medical imaging technology, but the structure of surgical needles has remained unchanged. This work presents a wire-driven 3D steerable, 3D-printed active needle for improved guidance inside the tissue toward the target. The needle is manipulated by 3 embedded tendons via a programmed motorized control unit. Feasibility tests in a tissue phantom showed an average 3D needle angular deflection of about 11°. This amount of angular deflection is expected to assist prostate brachytherapy via a curvilinear approach.

Mosquito proboscis-inspired needle insertion to reduce tissue deformation and organ displacement

This study investigates mosquito proboscis-inspired (MPI) insertion applied to the clinically used biopsy needle to reduce tissue deformation and organ displacement. Advanced medical imagining has enabled early-stage identification of cancerous lesions that require needle biopsy for minimally invasive tissue sampling and pathological analysis. Accurate cancer diagnosis depends on the accuracy of needle deployment to the targeted cancerous lesion site. However, currently available needle delivery systems deform and move soft tissue and organs, leading to a non-diagnostic biopsy or undersampling of the target. Two features inspired by the mosquito proboscis were adopted for MPI insertion in prostate biopsy: (1) the harpoon-shape notches at the needle tip and (2) reciprocating needle-cannula motions for incremental insertion. The local tissue deformation and global prostate displacement during the MPI vs. traditional direct insertions were quantified by optically tracking the displacement of particle-embedded tissue-mimicking phantoms. Results show that the MPI needle insertion reduced both local tissue deformation and global prostate displacement because of the opposite needle-cannula motions and notches which stabilized and reduced the tissue deformation during insertion. Findings provide proof of concept for MPI insertion in the clinical biopsy procedures as well as insights of needle–tissue interaction for future biopsy technology development.

Developing a novel force forecasting technique for early prediction of critical events in robotics

Safety critical events in robotic applications can often be characterized by forces between the robot end-effector and the environment. One application in which safe interaction between the robot and environment is critical is in the area of medical robots. In this paper, we propose a novel Compact Form Dynamic Linearization Model-Free Prediction (CFDL-MFP) technique to predict future values of any time-series sensor data, such as interaction forces. Existing time series forecasting methods have high computational times which motivates the development of a novel technique. Using Autoregressive Integrated Moving Average (ARIMA) forecasting as benchmark, the performance of the proposed model was evaluated in terms of accuracy, computation efficiency, and stability on various force profiles. The proposed algorithm was 11% more accurate than ARIMA and maximum computation time of CFDL-MFP was 4ms, compared to ARIMA (7390ms). Furthermore, we evaluate the model in the special case of predicting needle buckling events, before they occur, by using only axial force and needle-tip position data. The model was evaluated experimentally for robustness with steerable needle insertions into different tissues including gelatin and biological tissue. For a needle insertion velocity of 2.5mm/s, the proposed algorithm was able to predict needle buckling 2.03s sooner than human detections. In biological tissue, no false positive or false negative buckling detections occurred and the rates were low in artificial tissue. The proposed forecasting model can be used to ensure safe robot interactions with delicate environments by predicting adverse force-based events before they occur.

A short bevel needle with a very thin tip improves vein puncture performance of peripheral intravenous catheters: An experimental study

BACKGROUND

Peripheral intravenous catheter placement is frequently unsuccessful at the first attempt. One suggested risk factor is a small vein size, because of the consequences of mechanical forces generated by the needle tip. We developed short bevel needles with a very thin tip and evaluated their puncture performance in two in vitro models.

METHODS

Peripheral intravenous catheters with a new needle ground using the lancet method (experimental catheter (L)) or backcut method (experimental catheter (B)) were compared with a conventional peripheral intravenous catheter (Surshield Surflo®) in a penetration force test and a tube puncture test. Penetration forces were measured when peripheral intravenous catheters penetrated a polyethylene sheet. The tube puncture test was used to evaluate whether the peripheral intravenous catheters could puncture a polyvinyl chloride tube at two positions, at the center and at 0.5 mm from the center of the tube.

RESULTS

Mean penetration forces at the needle tip produced by experimental catheters (L) (0.05 N) and (B) (0.04 N) were significantly lower than those produced by the conventional catheter (0.09 N) (p < 0.01). At the catheter tip, mean forces produced by experimental catheter (B) and the conventional catheter were 0.16 N and 0.26 N, respectively (p < 0.05). In the tube puncture test, the frequency at which the conventional catheter punctured the center-shifted site on the tube at an angle of 20° and speed of 50 mm/min was low (40%). In contrast, experimental catheters (L) and (B) were 100% successful at puncturing both the center and center-shifted sites at 20°.

CONCLUSION

Puncture performance was comparable between the lancet-ground and backcut-ground needles except for penetration forces at the catheter tip. The experimental catheters produced lower penetration forces and induced puncture without target displacement at smaller angles compared with the conventional catheter. Therefore, optimization of the needle can prevent vein deformation and movement, which may increase the first-attempt success rate.

Injectable Biomedical Devices for Sensing and Stimulating Internal Body Organs

The rapid pace of progress in implantable electronics driven by novel technology has created devices with unconventional designs and features to reduce invasiveness and establish new sensing and stimulating techniques. Among the designs, injectable forms of biomedical electronics are explored for accurate and safe targeting of deep-seated body organs. Here, the classes of biomedical electronics and tools that have high aspect ratio structures designed to be injected or inserted into internal organs for minimally invasive monitoring and therapy are reviewed. Compared with devices in bulky or planar formats, the long shaft-like forms of implantable devices are easily placed in the organs with minimized outward protrusions via injection or insertion processes. Adding flexibility to the devices also enables effortless insertions through complex biological cavities, such as the cochlea, and enhances chronic reliability by complying with natural body movements, such as the heartbeat. Diverse types of such injectable implants developed for different organs are reviewed and the electronic, optoelectronic, piezoelectric, and microfluidic devices that enable stimulations and measurements of site-specific regions in the body are discussed. Noninvasive penetration strategies to deliver the miniscule devices are also considered. Finally, the challenges and future directions associated with deep body biomedical electronics are explained.

An adaptive finite element model for steerable needles

Penetration of a flexible and steerable needle into a soft target material is a complex problem to be modelled, involving several mechanical challenges. In the present paper, an adaptive finite element algorithm is developed to simulate the penetration of a steerable needle in brain-like gelatine material, where the penetration path is not predetermined. The geometry of the needle tip induces asymmetric tractions along the tool–substrate frictional interfaces, generating a bending action on the needle in addition to combined normal and shear loading in the region where fracture takes place during penetration. The fracture process is described by a cohesive zone model, and the direction of crack propagation is determined by the distribution of strain energy density in the tissue surrounding the tip. Simulation results of deep needle penetration for a programmable bevel-tip needle design, where steering can be controlled by changing the offset between interlocked needle segments, are mainly discussed in terms of penetration force versus displacement along with a detailed description of the needle tip trajectories. It is shown that such results are strongly dependent on the relative stiffness of needle and tissue and on the tip offset. The simulated relationship between programmable bevel offset and needle curvature is found to be approximately linear, confirming empirical results derived experimentally in a previous work. The proposed model enables a detailed analysis of the tool–tissue interactions during needle penetration, providing a reliable means to optimise the design of surgical catheters and aid pre-operative planning.

Magnetic Needle Steering in Soft Phantom Tissue

Needle steering is a technology for guiding needles around sensitive internal obstacles in minimally invasive surgery. Traditional techniques apply rotation at the base of a needle with an asymmetric tip, enabling steering through the redirection of radial forces. Magnetic steering of catheters and continuum manipulators is another technology that allows steering of a shaft in the body. Both of these techniques rely on mechanical or manual shaft advancement methods. Needle steering has not achieved widespread clinical use due to several limitations: 1- buckling and compression effects in the shaft and needle rotation cause excessive tissue damage; 2- torsion effects on the shaft and needle deflection at tissue boundaries lead to difficulty in control; and 3- restricted radius of curvature results in limited workspace. Magnetically steered catheters and continuum manipulators also suffer from limited curvature and the possibility of buckling. This paper proposes a novel needle steering method empowered by electromagnetic actuation that overcomes all of the aforementioned limitations, making it a promising option for further study toward healthcare applications.

GantryMate: A Modular MR-Compatible Assistance System for MR-Guided Needle Interventions

Percutaneous minimally invasive interventions are difficult to perform in closed-bore high-field magnetic resonance systems owing to the limited space between magnet and patient. To enable magnetic resonance–guided needle interventions, we combine a small, patient-mounted assistance system with a real-time instrument tracking sequence based on a phase-only cross-correlation algorithm for marker detection. The assistance system uses 2 movable plates to align an external passive marker with the anatomical target structure. The targeting accuracy is measured in phantom experiments, yielding a precision of 1.7 ± 1.0 mm for target depths up to 38 ± 13 mm. In in vivo experiments, the possibility to track and target static and moving structures is demonstrated.

Ultrasound needle segmentation and trajectory prediction using excitation network

PURPOSE

Ultrasound (US)-guided percutaneous kidney biopsy is a challenge for interventionists as US artefacts prevent accurate viewing of the biopsy needle tip. Automatic needle tracking and trajectory prediction can increase operator confidence in performing biopsies, reduce procedure time, minimize the risk of inadvertent biopsy bleedings, and enable future image-guided robotic procedures.

METHODS

In this paper, we propose a tracking-by-segmentation model with spatial and channel "Squeeze and Excitation" (scSE) for US needle detection and trajectory prediction. We adopt a light deep learning architecture (e.g. LinkNet) as our segmentation baseline network and integrate the scSE module to learn spatial information for better prediction. The proposed model is trained with the US images of anonymized kidney biopsy clips from 8 patients. The contour is obtained using the border-following algorithm and area calculated using Green formula. Trajectory prediction is made by extrapolating from the smallest bounding box that can capture the contour.

RESULTS

We train and test our model on a total of 996 images extracted from 102 short videos at a rate of 3 frames per second from each video. A set of 794 images is used for training and 202 images for testing. Our model has achieved IOU of 41.01%, dice accuracy of 56.65%, F1-score of 36.61%, and root-mean-square angle error of 13.3[Formula: see text]. We are thus able to predict and extrapolate the trajectory of the biopsy needle with decent accuracy for interventionists to better perform biopsies.

CONCLUSION

Our novel model combining LinkNet and scSE shows a promising result for kidney biopsy application, which implies potential to other similar ultrasound-guided biopsies that require needle tracking and trajectory prediction.

Quantitative Evaluation of Bleeding during Blood Vessel Puncture Caused by Fine Needle in Lower Abdomen

Inserting a fine needle presents a trade-off problem between safety and accuracy. As one of the serious complications due to tissue damages during needle insertion, severe bleeding often occurs owing to blood vessel puncture. However, there are few researches to evaluate the safety quantitatively regarding bleeding during the fine needle insertion. Therefore, the purpose of this study was the quantitative evaluation of the amount of bleeding due the artery and vein puncture depending on the needle size. We developed a blood circulation system for measuring the amount of bleeding due to blood vessel puncture. Using the system, the amount of bleeding due to different needle sizes was evaluated. The results suggested that the amount of bleeding per unit time increased depending on the needle radius. According to ordinal safety standards, the 22-gauge needle is appropriate for insertion into the lower abdomen.

Prospect of robotic assistance for fully automated brachytherapy seed placement into skull base: Experimental validation in phantom and cadaver

BACKGROUND AND PURPOSE

To investigate the feasibility and accuracy of robot-assisted brachytherapy for skull base tumours.

MATERIAL AND METHODS

A custom robot system was tested on both phantom and cadaveric specimen. Cone beam CT (CBCT) images were transferred to the graphical user interface (GUI) for planning trajectories and the data were sent to the robot control unit. Following registration, the puncture needle was inserted into the target by the robot under navigation guidance, and seeds were implanted. Placement error was instantly displayed on the GUI; the result was verified after postoperative image scanning.

RESULTS

A total of 150 seeds (100 for phantom experiments, 50 for cadaveric studies) were deposited by the robot system. In phantom experiments the mean placement error was 0.57 ± 0.21 mm (measured by the navigation system) vs. 1.41 ± 0.38 mm (measured by image fusion) (p < 0.001); in cadaveric studies the corresponding figures were 0.60 ± 0.30 mm vs. 2.48 ± 0.32 mm (p < 0.001). There was no significant difference for comparison of accuracy test in phantom experiments (p = 0.173) as well as in cadaveric studies (p = 0.354). Accuracy was better in the phantom experiment than in cadaveric studies (p < 0.001).

CONCLUSIONS

The performance of robot-assisted skull base brachytherapy is feasible and accurate. Dosimetric coverage will need to be demonstrated in further studies.

Needle deflection and tissue sampling length in needle biopsy

This study investigates the effect of needle tip geometry on the needle deflection and tissue sampling length in biopsy. Advances in medical imaging have allowed the identification of suspicious cancerous lesions which then require needle biopsy for tissue sampling and subsequent confirmatory pathological analysis. Precise needle insertion and adequate tissue sampling are essential for accurate cancer diagnosis and individualized treatment decisions. However, the single-bevel needles in current hand-held biopsy devices often deflect significantly during needle insertion, causing variance in the targeted and actual locations of the sampled tissue. This variance can lead to inaccurate sampling and false-negative results. There is also a limited understanding of factors affecting the tissue sampling length which is a critical component of accurate cancer diagnosis. This study compares the needle deflection and tissue sampling length between the existing single-bevel and exploratory multi-bevel needle tip geometries. A coupled Eulerian-Lagrangian finite element analysis was applied to understand the needle-tissue interaction during needle insertion. The needle deflection and tissue sampling length were experimentally studied using tissue-mimicking phantoms and ex-vivo tissue, respectively. This study reveals that the tissue separation location at the needle tip affects both needle deflection and tissue sampling length. By varying the tissue separation location and creating a multi-bevel needle tip geometry, the bending moments induced by the insertion forces can be altered to reduce the needle deflection. However, the tissue separation location also affects the tissue contact inside the needle groove, potentially reducing the tissue sampling length. A multi-bevel needle tip geometry with the tissue separation point below the needle groove face may reduce the needle deflection while maintaining a long tissue sampling length. Results from this study can guide needle tip design to enable the precise needle deployment and adequate tissue sampling for the needle biopsy procedures.

Modeling of geometry and insertion force of a new lancet medical needle

Lancet needle is a typical medical treatment device. Its tip consists of two lancet planes and one bevel plane. When the lancet needle is inserted into soft organ tissue, the insertion force may influence the needle cutting direction and treatment effect and increase the pain. One of the main factors affecting this insertion force is the geometry of the needle tip. Based on the research on the shape and processing method of the conventional lancet needle, a new lancet needle tip geometry was obtained by adjusting the relative position of the grinding wheel to the needle. A mathematical model of this new lancet needle was established. The relationship between processing parameters and needle shape was analyzed, and the needle insertion force was predicted. Compared with the conventional lancet needle, the new lancet needle is sharper, and the insertion force on the cutting edge is smaller. However, this change in the grinding position of the needle lancet plane has a great influence on the shape of needle tip near the intersection of the bevel plane and the lancet plane. Some special second bevel angle and rotated angle will cause a large change in the specific force at the intersection place, which is not conducive to reducing the insertion force.

Robot-assisted flexible needle insertion using universal distributional deep reinforcement learning

PURPOSE

Flexible needle insertion is an important minimally invasive surgery approach for biopsy and radio-frequency ablation. This approach can minimize intraoperative trauma and improve postoperative recovery. We propose a new path planning framework using multi-goal deep reinforcement learning to overcome the difficulties in uncertain needle-tissue interactions and enhance the robustness of robot-assisted insertion process.

METHODS

This framework utilizes a new algorithm called universal distributional Q-learning (UDQL) to learn a stable steering policy and perform risk management by visualizing the learned Q-value distribution. To further improve the robustness, universal value function approximation is leveraged in the training process of UDQL to maximize generalization and connect to diagnosis by adapting fast re-planning and transfer learning.

RESULTS

Computer simulation and phantom experimental results show our proposed framework can securely steer flexible needles with high insertion accuracy and robustness. The framework also improves robustness by providing distribution information to clinicians for diagnosis and decision making during surgery.

CONCLUSIONS

Compared with previous methods, the proposed framework can perform multi-target needle insertion through single insertion point qunder continuous state space model with higher accuracy and robustness.

Enhancing medial layer recellularization of tissue-engineered blood vessels using radial microchannels

Aim: Cell repopulation of tissue-engineered vascular grafts (TEVGs) from decellularized arterial scaffolds is limited by dense concentric tunica media layers which impede cells migrating radially between the layers. We aimed to develop and validate a new microneedle device to modify decellularized carotid arteries with radial microchannels to enhance medial layer repopulation. Material & methods: Modified decellularized porcine arteries were seeded with rat mesenchymal stem cells using either standard longitudinal injection, or a dual vacuum-perfusion bioreactor. Mechanical tests were used to assess the arterial integrity following modification. Results & conclusion: The method herein achieved radial recellularization of arteries in vitro without significant loss of mechanical integrity, Thus, we report a novel method for successful radial repopulation of decellularized carotid artery-based tissue-engineered vascular grafts.

Transjugular Intrahepatic Portosystemic Shunt Creation Using a Radiofrequency Wire: Acute Feasibility Study in Swine

The feasibility of a radiofrequency (RF) wire to replace the needle trocar for the creation of a transjugular intrahepatic portosystemic shunt (TIPS) was assessed in 3 swine by using fluoroscopy and intravascular ultrasonography (IVUS). RF wire passes were successful from hepatic to portal vein and from inferior vena cava to portal vein. Technical success was achieved using both IVUS guidance and carbon dioxide portography. The wire tracked a straight course under RF energy application without subjective deflection and, when centrally advanced, served as the working wire for completing the TIPS in 2 attempts with stent graft deployment. No procedural adverse events from the use of RF wire were observed.

A Radial Clutch Needle for Facile and Safe Tissue Compartment Access

Efficient and safe access to targeted therapeutic sites is a universal challenge in minimally invasive medical intervention. Percutaneous and transluminal needle insertion is often performed blindly and requires significant user skill and experience to avoid complications associated with the damage of underlying tissues or organs. Here, we report on the advancement of a safer needle with a radial mechanical clutch, which is designed to prevent overshoot injuries through the automatic stopping of the needle once a target cavity is reached. The stylet-mounted clutch system is inexpensive to manufacture and compatible with standard hypodermic or endoscopic needles, and therefore can be adapted to achieve safe access in a myriad of minimally invasive procedures, including targeted drug delivery, at-home and in-hospital intravenous access, laparoscopic and endo- and trans-luminal interventions. Here, we demonstrate the clutch needle design optimization and illustrate its potential for rapid and safe minimally invasive cannulation.

Influence of needling conditions on the corneal insertion force

Needle insertion plays an important part in the process of corneal graft surgery. In this paper, a three-dimensional symmetry model of the human cornea is constructed using the finite element method. Simplification of specific optic physiology is defined for the model: The cornea constrained by the sclera is presented as two layers consisting of epithelium and stroma. A failure criterion based on the distortion energy theory has been proposed to predict the insertion process of the needle. The simulation results show a good agreement with the experimental data reported in the literature. The influence of needling conditions (e.g. insertion velocity, rotation parameters and vibration parameters) on the insertion force are then discussed. In addition, a multi-objective optimization based on particle swarm optimization (PSO) is applied to reduce the insertion force. The numerical results provide guidelines for selecting the motion parameters of the needle and a potential basis for further developments in robot-assisted surgery.

Design of an ultra-thin steerable probe for percutaneous interventions and preliminary evaluation in a gelatine phantom

Needles with diameter under 1 mm are used in various medical applications to limit the risk of complication and patient discomfort during the procedure. Next to a small diameter, needle steerability is an important property for reaching targets located deep inside the body accurately and precisely. In this paper, we present a 0.5-mm prototype probe which is able to steer in three dimensions (3D) without the need of axial rotation. The prototype consists of three Nitinol wires (each with a diameter of 0.125 mm) with a pre-curved tip. The wires are kept together by a stainless steel tube. Each wire is clamped to a block which translates along a leadscrew, the rotation of the latter being controlled by a wheel connected at the distal end of the leadscrew. The tip bends upon retraction of one or two wires. When pushed through a soft solid structure (e.g., a soft tissue or soft tissue phantom), the probe deflects due to off-axis forces acting on its tip by the surrounding structure. We tested the performance of the prototype into a 10% wt gelatine phantom, in terms of the predictability of the steering direction and the controllability of the final position after steering inside the substrate. The results showed that the probe steered in the direction of the retracted wire and that the final position varied from small deflections from the straight path when the wires were slightly retracted, to sharp curvatures for large wire retraction. The probe could be used in various applications, from cases where only a small correction of the path in one direction is needed to cases where the path to be followed includes obstacles and curves in multiple directions.

Spatio-temporal deep learning models for tip force estimation during needle insertion

PURPOSE

Precise placement of needles is a challenge in a number of clinical applications such as brachytherapy or biopsy. Forces acting at the needle cause tissue deformation and needle deflection which in turn may lead to misplacement or injury. Hence, a number of approaches to estimate the forces at the needle have been proposed. Yet, integrating sensors into the needle tip is challenging and a careful calibration is required to obtain good force estimates.

METHODS

We describe a fiber-optic needle tip force sensor design using a single OCT fiber for measurement. The fiber images the deformation of an epoxy layer placed below the needle tip which results in a stream of 1D depth profiles. We study different deep learning approaches to facilitate calibration between this spatio-temporal image data and the related forces. In particular, we propose a novel convGRU-CNN architecture for simultaneous spatial and temporal data processing.

RESULTS

The needle can be adapted to different operating ranges by changing the stiffness of the epoxy layer. Likewise, calibration can be adapted by training the deep learning models. Our novel convGRU-CNN architecture results in the lowest mean absolute error of [Formula: see text] and a cross-correlation coefficient of 0.9997 and clearly outperforms the other methods. Ex vivo experiments in human prostate tissue demonstrate the needle's application.

CONCLUSIONS

Our OCT-based fiber-optic sensor presents a viable alternative for needle tip force estimation. The results indicate that the rich spatio-temporal information included in the stream of images showing the deformation throughout the epoxy layer can be effectively used by deep learning models. Particularly, we demonstrate that the convGRU-CNN architecture performs favorably, making it a promising approach for other spatio-temporal learning problems.

Steerable catheters for minimally invasive surgery: a review and future directions

The steerable catheter refers to the catheter that is manipulated by a mechanism which may be driven by operators or by actuators. The steerable catheter for minimally invasive surgery has rapidly become a rich and diverse area of research. Many important achievements in design, application and analysis of the steerable catheter have been made in the past decade. This paper aims to provide an overview of the state of arts of steerable catheters. Steerable catheters are classified into four main groups based on the actuation principle: (1) tendon driven catheters, (2) magnetic navigation catheters, (3) soft material driven catheters (shape memory effect catheters, steerable needles, concentric tubes, conducting polymer driven catheters and hydraulic pressure driven catheters), and (4) hybrid actuation catheters. The advantages and limitations of each of them are commented and discussed in this paper. The future directions of research are summarized.

Simulation of biopsy bevel-tipped needle insertion into soft-gel

Planning and practice of surgical procedures can be improved through the use of modelling. This study provides an insight into the biopsy needle (i.e. hollow cannula) and needle-tissue interactions using a modelling approach, thus enabling the optimization of needle-tip designs not only for training but also for the planning of surgical procedures. Simulations of needle insertion into agar gel were performed using a Coupled Eulerian-Lagrangian (CEL) based finite element (FE) analysis, adapted for large deformation and tissue fracture. The experimental work covers needle insertion into 3% agar gel using a needle with a beveled tip of various angles, to assess the validity of the simulation. The simulated needle deflection and insertion force for two needles (i.e. Needle 1 with 18° bevel angle and Needle 2 with 27° bevel angle) were compared with corresponding experimental results. The contact stress (i.e. contact pressure) on the needles from the agar gel during the insertion of the needles were also studied. Observations indicate that varying the needle bevel angle from 27° to 18° results in a decrease of the peak force (i.e. puncture force) and an increase in needle deflection. Quantitatively, the percentage errors between the experimental data and the FE model for the total insertion force along the z-direction (i.e. Z Force) for Needle 1 and 2 were 4% and 4.8% (p > 0.05), respectively. Similarly, needle deflection percentage errors along the x-z plane were 5.7% and 10% respectively. Therefore, the forces and needle deflection values predicted by the simulation are a close approximation of the experimental model, validating the Coupled Eulerian-Lagrangian based FE model. Thus, providing an experimentally validated model for biopsy and cytology needle design in silico that has the potential to replace the current build and break approach of needle design used by manufacturers.