Oxygen Vacancy-Induced Nonradical Degradation of Organics: Critical Trigger of Oxygen (O2) in the Fe-Co LDH/Peroxymonosulfate System

Paint sludge derived activated carbon encapsulating with cobalt nanoparticles for non-radical activation of peroxymonosulfate

Industrial solid waste management and recycling are important to environmental sustainability. In this study, cobalt (Co) nanoparticles encapsulated in paint sludge-derived activated carbon (AC) were fabricated. The Co-AC possessed high conductivity, magnetic properties and abundant metal oxide impurities (TiAlSiOx), which was applied as multifunctional catalyst for peroxymonosulfate (PMS) activation. Compared to pure AC, the Co-AC exhibited significant enhanced performance for degradation of tetracycline hydrochloride (TCH) via PMS activation. Mechanism studies by in situ Raman spectroscopy, Fourier infrared spectroscopy, electrochemical analysis and electron paramagnetic resonance suggested that surface-bonded PMS (PMS*) and singlet oxygen (1O2) are the dominant reactive species for TCH oxidation. The non-radical species can efficiently oxidize electron-rich pollutants with high efficiency, which minimized the consumption of PMS and the catalyst. The removal percentages of TCH reached 97 % within 5 min and ∼ 99 % within 15 min in the Co-AC/PMS system. The Co active sites facilitated PMS adsorption to form the PMS* and the TiAlSiOx impurities provided abundant oxygen vacancy for generation of the 1O2. In addition, the Co-AC/PMS system achieved high efficiency and stability for oxidation of the target pollutants over a long-term continuous operation. This work not only offers a cost-effective approach for recycling industrial waste but also provides new insights into the application of waste-derived catalyst for environmental remediation.

Self-motivated photoaging of microplastics by biochar-dissolved organic matter under different pyrolysis temperatures

Dissolved organic matter (DOM) released from biochar (BDOM) can interact with microplastics (MPs) in the environment, inevitably affecting their environmental behaviour. Information regarding the influence of BDOM on MPs during photoaging and associated variations in the MP aging mechanism remains unclear. This study evaluated the effect of BDOM on the aging of polystyrene (PS) MPs. The results showed that among three pyrolysis temperatures, low-temperature BDOM significantly enhanced the photoaging process of PS MPs, with the smallest average particle size and highest carbonyl index value after 15 days of aging under light conditions. The DOM level decreased after 5 days, increased after 5-10 days, and stabilised after 15 d. BDOM accelerates PS MPs aging, leading to more DOM released from PS, which can be transformed into 1O2 via triplet-excited state (3DOM⁎ and 3PS⁎) to further enhance PS MPs aging, resulting in the realisation of the self-accelerated aging process of PS MPs. 1O2 plays a crucial role in the self-motivated accelerated aging process of PS MPs. These findings provide new insights into the effects of the DOM structure and composition on reactive oxygen species generation during MPs aging.

Surface Hydroxyl and Oxygen Vacancies Engineering in ZnSnAl LDH: Synergistic Promotion of Photocatalytic Oxidation of Aromatic VOCs

Photocatalytic oxidation has gained great interest in environmental remediation, but it is still limited by its low efficiency and catalytic deactivation in the degradation of aromatic VOCs. In this study, we concurrently regulated the surface hydroxyl and oxygen vacancies by introducing Al into ZnSn layered double hydroxide (LDH). The presence of distorted Al species induced local charge redistribution, leading to the remarkable formation of oxygen vacancies. These oxygen vacancies subsequently increased the amount of surface hydroxyl and elongated its bond length. The synergistic effects of surface hydroxyl and oxygen vacancies greatly enhanced reactant adsorption-activation and facilitated charge transfer to generate •OH, •O2-, and 1O2, resulting in highly efficient oxidation and ring-opening of various aromatic VOCs. Compared with commercial TiO2, the optimized ZnSnAl-50 catalyst exhibited about 2-fold activity for the toluene and styrene degradation and 10-fold activity for the chlorobenzene degradation. Moreover, ZnSnAl-50 demonstrated exceptional stability in the photocatalytic oxidation of toluene under a wide humidity range of 0-75%. This work marvelously improves the photocatalytic efficiency, stability, and adaptability through a novel strategy of surface hydroxyl and oxygen vacancies engineering.

Selective electrophilic attack towards organic micropollutants with superior Fenton-like activity by biochar-supported cobalt single-atom catalyst

The global shortage of freshwater and inadequate supply of clean water have necessitated the implementation of robust technologies for wastewater purification, and Fenton-like chemistry is a highly-promising approach. However, realizing the rapid Fenton-like chemistry for high-efficiency degradation of organic micropollutants (OMs) remains challenging. Herein, one novel system was constructed by a Co single-atom catalyst activating peroxymonosulfate (PMS), and the optimal system (SA-Co-NBC-0.2/PMS) achieved unprecedented catalytic performance towards a model OM [Iohexol (IOH)], i.e., almost 100% decay ratio in only 10 min (the observed rate constant: 0.444 min-1) with high electrophilic species 1O2 (singlet oxygen) generation. Theoretical calculations unveiled that Co-N4 sites preferred to adsorb the terminal-O of PMS (more negative adsorption energy than other O sites: -32.67 kcal/mol), promoting the oxidation of PMS to generate 1O2. Iodine (I)23 (0.1097), I24 (0.1154) and I25 (0.0898) on IOH with higher f- electrophilic values were thus identified as the main attack sites. Furthermore, 16S ribosomal RNA high-throughput sequencing and quantitative structure-activity relationship analysis illustrated the environmentally-benign property of the SA-Co-NBC-0.2 and the tapering ecological risk during IOH degradation process. Significantly, this work comprehensively checked the competence of the SA-Co-NBC-0.2/PMS system for organics abatement in practical wastewater.

Mechanism of interaction between ascorbic acid and soil iron-containing minerals for peroxydisulfate activation and organophosphorus flame retardant degradation

Soil constituents may play an important role in peroxydisulfate (PDS)-based oxidation of organic contaminants in soil. Iron-containing minerals (Fe-minerals) have been found to promote PDS activation for organics degradation. Our study found that ascorbic acid (H2A) could enhance PDS activation by soil Fe-minerals for triphenyl phosphate (TPHP) degradation. Determination and characterization analyses of Fe fractions showed that H2A could induce the reductive dissolution of solid Fe-minerals and the increasing of oxygen vacancies/hydroxyl groups content on Fe-minerals surface. The increasing of divalent Fe (Fe(II)) accelerated PDS activation to generate reactive oxygen species (ROS). Electron paramagnetic resonance (EPR) and quenching studies showed that sulfate radicals (SO4•-) and hydroxyl radicals (HO•) contributed significantly to TPHP degradation. The composition and content of Fe-minerals and soil organic matter (SOM) markedly influenced ROS transformations. Surface-bond and structural Fe played the main role in the production of Fe(II) in reaction system. The high-concentration SOM could result in ROS consumption and degradation inhibition. Density functional theory (DFT) studies revealed that H2A is preferentially adsorbed at α-Fe2O3(012) surface through Fe-O-C bridges rather than hydrogen bonds. After absorption, H atoms on H2A may further be migrated to adjacent O atoms on the α-Fe2O3(012) surface. With the transformation of H atoms to the α-Fe2O3(012) surface, the Fe-O-C bridge is broken and one electron is transferred from the O to Fe atom, inducing the reduction of trivalent Fe (Fe(III)) atom. MS/MS2 analysis, HPLC analysis, and toxicity assessment demonstrated that TPHP was transformed to less toxic 4-hydroxyphenyl diphenyl phosphate (OH-TPHP), diphenyl hydrogen phosphate (DPHP), and phenyl phosphate (PHP) through phenol-cleavage and hydroxylation processes, and even be mineralized in reaction system.

Role of the In-Situ-Formed Surface (Pt-S-O)-Ti Active Structure in SO2-Promoted C3H8 Combustion over a Pt/TiO2 Catalyst

Typically, SO2 unavoidably deactivates catalysts in most heterogeneous catalytic oxidations. However, for Pt-based catalysts, SO2 exhibits an extraordinary boosting effect in propane catalytic oxidation, but the promotive mechanism remains contentious. In this study, an in situ-formed tactful (Pt-S-O)-Ti structure was concluded to be a key factor for Pt/TiO2 catalysts with a substantial SO2 tolerance ability. The experiments and theoretical calculations confirm that the high degree of hybridization and orbital coupling between Pt 5d and S 3p orbitals enable more charge transfer from Pt to S species, thus forming the (Pt-S-O)-Ti structure with the oxygen atom dissociated from the chemisorbed O2 adsorbed on oxygen vacancies. The active oxygen atom in the (Pt-S-O)-Ti active structure is a robust site for C3H8 adsorption, leading to a better C3H8 combustion performance. This work can provide insights into the rational design of chemical bonds for high SO2 tolerance catalysts, thereby improving economic and environmental benefits.

Aeration-Free In Situ Fenton-like Reaction: Specific Adsorption and Activation of Oxygen on Heterophase Oxygen Vacancies

Aeration accounts for 35-51% of the overall energy consumption in wastewater treatment processes and results in an annual energy consumption of 5-7.5 billion kWh. Herein, a solar-powered continuous-flow device was designed for aeration-free in situ Fenton-like reactions to treat wastewater. This system is based on the combination of TiO2-x/W18O49 featuring heterophase oxygen vacancy interactions with floating reduced graphene/polyurethane foam, which produces hydrogen peroxide in situ at the rates of up to 4.2 ppm h-1 with degradation rates of more than 90% for various antibiotics. The heterophase oxygen vacancies play an important role in the stretching of the O-O bond by regulating the d-band center of TiO2-x/W18O49, promoting the hydrogenation of *·O2- or *OOH by H+ enrichment, and accelerating the production of reactive oxygen species by spontaneous adsorption of hydrogen peroxide. Furthermore, the degradation mechanisms of antibiotics and the treatment of actual wastewater were thoroughly investigated. In short, the study provides a meaningful reference for potentially undertaking the "aeration-free" in situ Fenton reaction, which can help reduce or even completely eradicate the aeration costs and energy requirements during the treatment of wastewater.

Synchronizing Efficient Purification of VOCs in Durable Solar Water Evaporation over a Highly Stable Cu/W18O49@Graphene Material

Solar-driven clean water production is challenged by VOCs (volatile organic compounds), which pose health risks in distilled water. Herein, we developed a Cu/W18O49@Graphene photothermal-photocatalytic material addressing VOCs contamination. Plasmonic coupling between Cu and W18O49 enhances light absorption, and 1-2 layers of graphene encapsulation protects oxygen vacancies within W18O49 while facilitating hot electron extraction, effectively mitigating their ultrafast relaxation. Density functional theory calculations revealed enhanced VOCs adsorption on graphene. These synergies address oxygen vacancy decay in W18O49 and provide more active sites for gas-liquid-solid triphase photocatalytic reactions. Integrated with a three-dimensional floating evaporator substrate, the optimized Cu/W18O49@Graphene material achieved an effective water evaporation rate of 1.41 kg m-2 h-1 (efficiency of 88.6%), exceptional stability (>120 h), and remarkable 99% phenol removal under 1 sun irradiation (1 kW m-2). This work provides a promising solution to mitigate VOCs contamination in solar-driven water evaporation.

Peroxymonosulfate activation by CuMn-LDH for the degradation of bisphenol A: Effect, mechanism, and pathway

The remediation of water contaminated with bisphenol A (BPA) has gained significant attention. In this study, a hydrothermal composite activator of Cu3Mn-LDH containing coexisting phases of cupric nitrate (Cu(NO3)2) and manganous nitrate (Mn(NO3)2) was synthesized. Advanced oxidation processes were employed as an effective approach for BPA degradation, utilizing Cu3Mn-LDH as the catalyst to activate peroxymonosulfate (PMS). The synthesis of the Cu3Mn-LDH material was characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM). According to the characterization data and screening experiments, Cu3Mn-LDH was selected as the best experimental material. Cu3Mn-LDH exhibits remarkable catalytic ability with PMS, demonstrating good degradation efficiency of BPA under neutral and alkaline conditions. With a PMS dosage of 0.25 g·L-1 and Cu3Mn-LDH dosage of 0.10 g·L-1, 10 mg·L-1 BPA (approximately 17.5 μM) can be completely degraded within 40 min, of which the TOC removal reached 95%. The reactive oxygen species present in the reaction system were analyzed by quenching experiments and EPR. Results showed that sulfate free radicals (SO4•-), hydroxyl free radicals (•OH), superoxide free radicals (•O2-), and nonfree radical mono-oxygen were generated, while mono-oxygen played a key role in degrading BPA. Cu3Mn-LDH exhibits excellent reproducibility, as it can still completely degrade BPA even after four consecutive cycles. The degradation intermediates of BPA were detected by GCMS, and the possible degradation pathways were reasonably predicted. This experiment proposes a nonradical degradation mechanism for BPA and analyzes the degradation pathways. It provides a new perspective for the treatment of organic pollutants in water.

Enhanced electron-transfer for peroxymonosulfate activation by Ni single sites adjacent to Ni nanoparticles

Oriented generation of specific reactive oxygen species (ROS) has been challenging in peroxymonosulfate (PMS)-based advanced oxidation processes (AOPs). In this work, we constructed a multifunctional catalyst composed of Ni NPs embedded in N-doped carbon nanotubes (NCNTs) with exposed Ni single-atom sites (Ni-NCNTs). The Ni-N4 single sites adjacent to the Ni NPs are more efficient for PMS adsorption and activation, resulting in enhanced production of singlet oxygen (1O2). More interesting, we demonstrated that the superoxide anion radical (O2•-) was generated from 1O2 reduction via the electron transfer from the graphitic-N sites of Ni-NCNTs rather than from O2 reduction or PMS decomposition as reported in previous studies. Thus, Ni-NCNTs can act as both electron acceptor and donor to trigger the cascade production of 1O2 and O2•-, respectively, leading to fast and selective degradation of aqueous organic pollutants. The graphitic-N adjacent to the aromatic π-conjugation of NCNTs facilitated chemisorption of 1O2 onto NCNTs via the strong π*-π interactions, and more importantly, donated the lone pair electrons to trigger the reduction of 1O2 to O2•-. This study unravels the mechanisms for enhanced production of ROS in the nanoconfined Fenton-like systems and shed new light on the application of multifunctional nanocatalyst for rapid wastewater decontamination.

Insight into cobalt substitution in LaFeO3-based catalyst for enhanced activation of peracetic acid: Reactive species and catalytic mechanism

In this study, a hollow sphere-like Co-modified LaFeO3 perovskite catalyst (LFC73O) was developed for peracetic acid (PAA) activation to degrade sulfamethoxazole (SMX). Results indicated that the constructed heterogeneous system achieved a 99.7% abatement of SMX within 30 min, exhibiting preferable degradation performance. Chemical quenching experiments, probe experiments, and EPR techniques were adopted to elucidate the involved mechanism. It was revealed that the superior synergistic effect of electron transfer and oxygen defects in the LFC73O/PAA system enhanced the oxidation ability of PAA. The Co atoms doped into LaFeO3 as the main active site with the original Fe atoms as an auxiliary site exhibited high activity to mediate PAA activation via the Co(III)/Co(II) cycle, generating carbon-centered radicals (RO·) including CH3C(O)O· and CH3C(O)OO·. The oxygen vacancies induced by cobalt substitution also served as reaction sites, facilitating the dissociation of PAA and production of ROS. Furthermore, the degradation pathways were postulated by DFT calculation and intermediates identification, demonstrating that the electron-rich sites of SMX molecules such as amino group, aromatic ring, and S-N bond, were more susceptible to oxidation by reactive species. This study offers a novel perspective on developing catalysts with the coexistence of multiple active units for PAA activation in environmental remediation.

Development of MoS2-stainless steel catalyst by 3D printing for efficient destruction of organics via peroxymonosulfate activation

Herein, a novel MoS2-stainless steel composite material was first synthetized via a 3D printing method (3DP MoS2-SS) for peroxymonosulfate (PMS) activation and organics degradation. Compared with MoS2-SS powder/PMS system (0.37 g/(m2/min)), 4.3-fold higher kFLO/SBET value was obtained in 3DP MoS2-SS/PMS system (1.60 g/(m2/min), resulting from the superior utilization of active sites. We observed that 3DP MoS2-SS significantly outperformed the 3DP SS due to the enhanced electron transfer rate and increased active sites. Moreover, Mo4+ facilitated the Fe2+/Fe3+ cycle, resulting in the rapid degradation of florfenicol (FLO). Quenching experiments and electron paramagnetic resonance spectra indicated that •OH, SO4•-, O2•- and 1O2 were involved in the degradation of FLO. The effect of influencing factors on the degradation of FLO were evaluated, and the optimized degradation efficiency of 98.69% was achieved at 1 mM PMS and pH of 3.0. Six degradation products were detected by UPLC/MS analyses and several possible degradation pathways were proposed to be the cleavage of C-N bonds, dechlorination, hydrolysis, defluorination and hydroxylation. In addition, 3DP MoS2-SS/PMS system also demonstrated superior degradation performance for 2-chlorophenol, acetaminophen, ibuprofen and carbamazepine. This study provided deep insights into the MoS2-SS catalyst prepared by 3DP technology for PMS activation and FLO-polluted water treatment.

N, S, and Cl tri-doped carbon boost the switching of radical to non-radical pathway in Fenton-like reactions: Synergism of N species and defects

Heteroatom doping represents a promising strategy for enhancing the generation of singlet oxygen (1O2) during the activation of peroxymonosulfate (PMS) using carbon-based catalysts; however, it remains a formidable challenge. In this study, we systematically controlled the structure of metal-free carbon-based materials by introducing different heteroatoms to investigate their efficacy in degrading organic pollutants in water via PMS activation. The results of reactive oxygen species detection showed that the dominant free radical in the four samples was different: CN (•SO4- and •OH), CNS (•O2-), CNCl (1O2), and CNClS (1O2). This led to the transformation of active species from free radicals to non-free radicals. The tri-doped carbons with nitrogen, sulfur, and chlorine (CNClS) exhibited exceptional performance in PMS activation and achieved a remarkable degradation efficiency of 95% within just 6 min for tetracycline. Moreover, a strong linear correlation was observed between the ratio of pyridine-N/graphite-N and ID/IG with the yield of 1O2, indicating that N species and defects play a crucial role in CNClS as they facilitate the transition from radical to non-radical pathways during PMS activation. These findings highlight the possibility that adjustable tri-heteroatom doping will expand the Fenton-like reaction for the treatment of actual wastewater.

Sn and dual-oxygen-vacancy in the Z-scheme Bi2Sn2O7/Sn/NiAl-layered double hydroxide heterojunction synergistically enhanced photocatalytic activity toward carbon dioxide reduction

Photocatalytic conversion of carbon dioxide (CO2) into high value-added chemicals is an attractive yet challenging process, primarily due to the readily recombination of hole-electron pairs in photocatalysts. Herein, dual-oxygen-vacancy mediated Z-scheme Bi2Sn2O7/Sn/NiAl-layered double hydroxide (VO,O-20BSL) heterojunctions were hydrothermally synthesized and subsequently modified with Sn monomers to enhance photocatalytic activity toward CO2 reduction. The abundance of oxygen vacancies endowed the VO,O-20BSL with extended optical adsorption, enhanced charges separation, and superior CO2 adsorption and activation. The interfacial charges transfer of the VO,O-20BSL was demonstrated to follow a Z-scheme mechanism via photochemical deposition of metal/metal oxide. Under visible light irradiation, the VO,O-20BSL exhibited the highest yields of carbon monoxide (CO) and methane (CH4), with values of 72.03 and 0.85 umol·g-1·h-1, respectively, which were 2.66 and 1.57 times higher than that of the VO-NiAl-layered double hydroxide (VO-1LDH). In situ diffuse reflectance infrared fourier transform spectroscopy (DRIFTS) revealed that carboxylic acid groups (COOH*) and aldehyde groups (CHO*) were the predominant intermediates during CO2 reduction, and accordingly, possible CO2 reduction pathways and mechanism were proposed. This study presents a feasible approach to incorporate dual vacancies into Z-scheme heterojunctions for CO2 reduction.

Mechanism insights into photo-assisted peroxymonosulfate activation on oxygen vacancy-enriched nolanites via an electron transfer regime

The utilization of photo-assisted persulfate activation for the removal of organic contaminants in water has garnered significant research interest in recent times. However, there remains a lack of clarity regarding specific contributions of light irradiation and catalyst structure in this process. Herein, a photo-assisted peroxymonosulfate (PMS) activation system is designed for the highly efficient degradation of organic contaminants on oxygen vacancy-enriched nolanites (Vo-FVO). Results suggest that the degradation of bisphenol A (BPA) in this system is a nonradical-dominated process via an electron transfer regime, in which VO improves the local electron density and thus facilitates the electron shuttling between BPA and PMS. During BPA degradation, PMS adsorbed at the surface of FVO-180 withdraws electrons near VO and forms FVO-PMS* complexes. Upon light irradiation, photoelectrons effectively restore the electron density around VO, thereby enabling a sustainable electron transfer for the highly efficient degradation of BPA. Overall, this work provides new insights into the mechanism of persulfate activation based on defects engineering in nolanite minerals.

Ozone Micronano-bubble-Enhanced Selective Degradation of Oxytetracycline from Production Wastewater: The Overlooked Singlet Oxygen Oxidation

The efficient and selective removal of refractory antibiotics from high-strength antibiotic production wastewater is crucial but remains a substantial challenge. In this study, a novel ozone micronano-bubble (MNB)-enhanced treatment system was constructed for antibiotic production wastewater treatment. Compared with conventional ozone, ozone MNBs exhibit excellent treatment efficiency for oxytetracycline (OTC) degradation and toxicity decrease. Notably, this study identifies the overlooked singlet oxygen (1O2) for the first time as a crucial active species in the ozone MNB system through probe and electron paramagnetic resonance methods. Subsequently, the oxidation mechanisms of OTC by ozone MNBs are systematically investigated. Owing to the high reactivity of OTC toward 1O2, ozone MNBs enhance the selective and anti-interference performance of OTC degradation in raw OTC production wastewater with complex matrixes. This study provides insights into the mechanism of ozone MNB-enhanced pollutant degradation and a new perspective for the efficient treatment of high-concentration industrial wastewater using ozone MNBs. In addition, this study presents a promising technology with scientific guidance for the treatment of antibiotic production wastewater.

Fe(II)-Modulated Microporous Electrocatalytic Membranes for Organic Microcontaminant Oxidation and Fouling Control: Mechanisms of Regulating Electron Transport toward Enhanced Reactive Oxygen Species Activation

Regulation of the fast electron transport process for the generation and utilization of reactive oxygen species (ROS) by achieving fortified electron "nanofluidics" is effective for electrocatalytic oxidation of organic microcontaminants. However, limited available active sites and sluggish mass transfer impede oxidation efficiency. Herein, we fabricated a conductive electrocatalytic membrane decorated with hierarchical porous vertically aligned Fe(II)-modulated FeCo layered double hydroxide nanosheets (Fe(II)-FeCo LDHs) in an electro-Fenton system to maximize exposure of active sites and expedite mass transfer. The nanospaced interlayers of Fe(II)-FeCo LDHs within the microconfined porous structure formed by its vertical nanosheets highly boost the micro/nanofluidic distribution of target pollutants to active centers/species, achieving accelerated mass transferability. Aliovalent substitution by Fe(II) activates in-plane metallics to maximize the available active sites and makes each Fe(II)-FeCo LDH nanosheet a geometrical nanocarrier for constructing a fast electron "nanofluidic" to accelerate Fe(II) regeneration in Fe(III)/Fe(II) cycles. As a result, the Fe(II)-FeCo LDHs exhibited improved reactivity in catalyzing H2O2 to •OH and 1O2. Accordingly, the membrane exhibited a higher atrazine degradation kinetic (0.0441 min-1) and degradation rate (93.2%), which were 4.7 and 2.1 times more than those of the bare carbon nanotube membrane, respectively. Additionally, the enhanced hydrophilic and strongly oxidized reactivity synergistically mitigated the organic fouling occurring in the pores and surface of the membrane. These findings clarify the activation mechanism of ROS over an innovative electrocatalytic membrane reactor design for organic microcontaminant treatment.

Efficient Removal of Antibiotic Resistance Genes through 4f-2p-3d Gradient Orbital Coupling Mediated Fenton-Like Redox Processes

Peroxymonosulfate (PMS) mediated radical and nonradical active substances can synergistically achieve the efficient elimination of antibiotic resistance genes (ARGs). However, enhancing interface electron cycling and optimizing the coupling of the oxygen-containing intermediates to improve PMS activation kinetics remains a major challenge. Here, Co doped CeVO4 catalyst (Co-CVO) with asymmetric sites was constructed based on Ce 4f-O 2p-Co 3d gradient orbital coupling. The catalyst achieved approximately 2.51×105 copies/mL of extracellular ARGs (eARGs) removal within 15 minutes, exhibited ultrahigh degradation rate (k=1.24 min-1 ). The effective gradient 4f-2p-3d orbital coupling precisely regulates the electron distribution of Ce-O-Co active center microenvironment, while optimizing the electronic structure of Co 3d states (especially the occupancy of eg ), promoting the adsorption of oxygen-containing intermediates. The generated radical and nonradical generated by interfacial electron cycling enhanced by the reduction reaction of PMS at the Ce site and the oxidation reaction at the Co site achieved a significant mineralization rate of ARGs (83.4 %). The efficient removal of ARGs by a continuous flow reactor for 10 hours significantly reduces the ecological risk of ARGs in actual wastewater treatment.

A novel copper oxide/titanium membrane integrated with peroxymonosulfate activation for efficient phenolic pollutants degradation

Herein, a novel CuO catalyst functionalized Ti-based catalytic membrane (FCTM) was prepared via the regulated electro-deposition technique followed with low-temperature calcination. The morphology of CuO catalyst and oxygen vacancy (OV) content can be controlled by adjusting the preparation conditions, under optimal condition (400 °C, electrolyte as sulfuric acid), the fern-shaped CuO catalyst was formed and the OV content was up to its highest level. Under the optimal treatment condition, the 4-chlorophenol (4-CP) removal of the membrane filtration combined with peroxymonosulfate (PMS) activation (MFPA) process was up to 98.2% (TOC removal of 88.2%). Mechanism studying showed that the enhanced performance in this system was mainly due to the increased production of singlet oxygen (1O2) via the co-effect of fern-shaped CuO (increased specific surface area) and its fine-tuned OV (precursor of 1O2), which not only synergistically enhanced adsorption ability but also offered more active sites for PMS activation. Theoretical calculations showed that the OV-rich CuO displayed high adsorption energy for PMS molecule, leading to the change in OO and OH bond (tend to 1O2) of the PMS molecule. Finally, the possible three degradation pathways of 4-CP were formed by the electrophilic attacking of 1O2.

New Insights into Selective Singlet Oxygen Production via the Typical Electroactivation of Oxygen for Water Decontamination

Selective production of singlet oxygen (1O2) as an electrophilic oxidant is crucial for the precise control of chemical targets in environmental fields. Herein, we proposed a strategy to construct a redox interface on electrodes, which can in situ produce inorganic metal hydroperoxides with appropriate oxidative ability during oxygen activation. Benefiting from atomic Cu sites (CuN4) in a copper-carbon aerogel electrode, almost complete production of 1O2 was achieved, thereby refraining the competitive formation of other reactive oxygen species. The fast electron transfer rate between CuN4 and electrogenerated H2O2 promoted the in situ formation of copper hydroperoxide (N4-Cu-OOH), thereby selectively and efficiently oxidizing intermediate O2•- to 1O2. The optimized production of 1O2 was up to 2583 μmol L-1 without additional chemical reagents. We further considered the high production of 1O2 for efficiently removing electron-rich organic pollutants from a complex water matrix. Fast kinetics was achieved and considered for removing various pollutants with electron-donating substituents in a nonradical oxidation pathway. The BPA degradation efficiency is less susceptible to the coexisting natural organic matter (NOM) and inorganic ions. Specifically, the kinetic constant for BPA removal is 34 times higher than that for a nanoparticle of a copper-carbon electrode while producing a hydroxyl radical. Our findings highlight the innovative interfacial surface engineering of an electrocatalytic O2 activation system to selectively generate 1O2 for future potential applications.

Generation and identification of 1O2 in catalysts/peroxymonosulfate systems for water purification

Catalysts for peroxymonosulfate (PMS) activation are appealing in the purification of organic wastewater. Singlet oxygen (1O2) is widely recognized as a crucial reactive species for degrading organic contaminants in catalysts/PMS systems due to its adamant resistance to inorganic anions, high selectivity, and broad pH applicability. With the rapid growth of studies on 1O2 in catalysts/PMS systems, it becomes necessary to provide a comprehensive review of its current state. This review highlights recent advancements concerning 1O2 in catalysts/PMS systems, with a primary focus on generation pathways and identification methods. The generation pathways of 1O2 are summarized based on whether (distinguished by the geometric structures of metal species) or not (distinguished by the active sites) the metal element is included in the catalysts. Furthermore, this review thoroughly discusses the influence of metal valence states and metal species with different geometric structures on 1O2 generation. Various potential strategies are explored to regulate the generation of 1O2 from the perspective of catalyst design. Identification methods of 1O2 primarily include electron paramagnetic resonance (EPR), quenching experiments, reaction in D2O solution, and chemical probe tests in catalysts/PMS systems. The principles and applications of these methods are presented comprehensively along with their applicability, possible disagreements, and corresponding solutions. Besides, an identifying procedure on the combination of main identification methods is provided to evaluate the role of 1O2 in catalysts/PMS systems. Lastly, several perspectives for further studies are proposed to facilitate developments of 1O2 in catalysts/PMS systems.

A multiple Kirkendall strategy for converting nanosized zero-valent iron to highly active Fenton-like catalyst for organics degradation

Nanosized zero-valent iron (nZVI) is a promising persulfate (PS) activator, however, its structurally dense oxide shell seriously inhibited electrons transfer for O-O bond cleavage of PS. Herein, we introduced sulfidation and phosphorus-doped biochar for breaking the pristine oxide shell with formation of FeS and FePO4-containing mixed shell. In this case, the faster diffusion rate of iron atoms compared to shell components triggered multiple Kirkendall effects, causing inward fluxion of vacancies with further coalescing into radial nanocracks. Exemplified by trichloroethylene (TCE) removal, such a unique "lemon-slice-like" nanocrack structure favored fast outward transfer of electrons and ferrous ions across the mixed shell to PS activation for high-efficient generation and utilization of reactive species, as evidenced by effective dechlorination (90.6%) and mineralization (85.4%) of TCE. [Formula: see text] contributed most to TCE decomposition, moreover, the SnZVI@PBC gradually became electron-deficient and thus extracted electrons from TCE with achieving nonradical-based degradation. Compared to nZVI/PS process, the SnZVI@PBC/PS system could significantly reduce catalyst dosage (87.5%) and PS amount (68.8%) to achieve nearly complete TCE degradation, and was anti-interference, stable, and pH-universal. This study advanced mechanistic understandings of multiple Kirkendall effects-triggered nanocrack formation on nZVI with corresponding rational design of Fenton-like catalysts for organics degradation.

Sulfur vacancy rich MoS2/FeMoO4 composites derived from MIL-53(Fe) as PMS activator for efficient elimination of dye: Nonradical 1O2 dominated mechanism

A novel MoS2/FeMoO4 composite was synthesized for the first time by introducing an inorganic promoter MoS2 into the MIL-53(Fe)-derived PMS-activator. The prepared MoS2/FeMoO4 could effectively activate peroxymonosulfate (PMS) toward 99.7% of rhodamine B (RhB) degradation in 20 min, and achieve a kinetic constant of 0.172 min-1, which is 10.8, 43.0 and 3.9 folds higher than MIL-53, MoS2 and FeMoO4 components, respectively. Both Fe(II) and sulfur vacancies are identified as the main active sites on catalyst surface, where sulfur vacancies can promote adsorption and electron migration between peroxymonosulfate and MoS2/FeMoO4 to accelerate peroxide bond activation. Besides, the Fe(III)/Fe(II) redox cycle was improved by reductive Fe0, S2- and Mo(IV) species to further boost PMS activation and RhB degradation. Comparative quenching experiment and in-situ electron paramagnetic resonance (EPR) spectra verified that SO4•-, •OH, 1O2 and O2•- were produced in the MoS2/FeMoO4/PMS system, while 1O2 dominates RhB elimination. In addition, the influences of various reaction parameters on RhB removal were examined and the MoS2/FeMoO4/PMS system exhibits good performance over a wide pH and temperature range, as well as coexistence with common inorganic ions and humic acid (HA). This study provides a new strategy for preparing MOF-derived composite with simultaneous introduction of MoS2 promotor and rich sulfur vacancies, and enables new insight into radical/nonradical pathway in PMS activation process.

Fast degradation of atrazine by nZVI-Cu0/PMS: Re-evaluation and quantification of reactive species, generation pathways, and application feasibility

Additive metal to zero-valent iron (ZVI) could enhance the reduction ability and the additive Cu0 was incorporated to ZVI to accelerate PMS activation with atrazine (ATZ) as target compound. The efficiencies of ATZ degradation and PMS decomposition climbed up firstly and then declined as Cu0 loading increased from 0.01 to 1.00 wt% with the maximums at 0.10 wt%. SO4•-, HO•, Fe(IV), O2•- and 1O2 were generated by nZVI-Cu0/PMS based on the results of electron paramagnetic resonance (EPR) and simultaneous degradation of nitrobenzene, ATZ, and methyl phenyl sulfoxide (PMSO). The rate constant of Fe(IV) and ATZ was estimated as 7 × 104 M-1∙s-1 via the variation of methyl phenyl sulfone (PMSO2)formation at different ATZ concentrations. However, Fe(IV) contributed negligibly to ATZ degradation due to the strong scavenging of Fe(IV) by PMS. SO4•- and HO• were the reactive species responsible for ATZ degradation and the yield ratio of SO4•- and HO• was about 8.70 at initial stage. Preliminary thermodynamic calculation on the possible activation ways revealed that the dominant production of SO4•- might originate from the atomic H reduction of PMS in the surface layer of nZVI-Cu0. Ten products of ATZ degradation were identified by HPLC/ESI/QTOF and the possible degradation pathways were analyzed combined with theoretical calculation on ATZ structure. The decrease of temperature or increase of solution pH led to the decline of ATZ degradation, as well as the individual addition of common ions (HCO3-, Cl-, SO42-, NH4+, NO3- and F-) and natural organic matters (NOM). In real water, ATZ was still efficiently degraded with the decontamination efficiency decreasing in the sequence of tap water > surface water > simulated wastewater > groundwater. For the treatment of ATZ-polluted continuous flow, nZVI-Cu0 in double-layer layout had a higher capacity than the single-layer mode. Meanwhile, the leaching TFe and TCu were limited. The results indicate nZVI-Cu0/PMS is applicable and the multiple-layer layout of nZVI-Cu0 is suggested for ATZ-polluted ground water and soil remediation.

Identifying the Role of Surface Hydroxyl on FeOCl in Bridging Electron Transfer toward Efficient Persulfate Activation

FeOCl is a highly effective candidate material for advanced oxidation process (AOP) catalysts, but there remain enormous uncertainties about the essence of its outstanding activity. Herein, we clearly elucidate the mechanism involved in the FeOCl-catalyzed perdisulfate (PDS) activation, and the role of surface hydroxyls in bridging the electron transfer between Fe sites and PDS onto the FeOCl/H2O interface is highlighted. ATR-FTIR and Raman analyses reveal that phosphate could suppress the activity of FeOCl via substituting its surface hydroxyls, demonstrating the essential role of hydroxyl in PDS activation. By the use of X-ray absorption fine structure and density functional theory calculations, we found that the polar surface of FeOCl experienced prominent hydrolyzation, which enriched abundant electrons within the microarea around the Fe site, leading to a stronger attraction between FeOCl and PDS. As a result, PDS adsorption onto the FeOCl/H2O interface was obviously enhanced, the bond length of O-O in adsorbed PDS was lengthened, and the electron transfer from Fe atoms to O-O was also promoted. This work proposed a new strategy for PDS-based AOP development and a hint of building efficient heterogeneous AOP catalysts via regulating the hydroxylation of active sites.

Dynamic active-site induced by host-guest interactions boost the Fenton-like reaction for organic wastewater treatment

In heterogeneous catalysis, uncovering the dynamic evolution of active sites in the working conditions is crucial to realizing increased activity and enhanced stability of catalyst in Fenton-like activation. Herein, we capture the dynamic changes in the unit cell of Co/La-SrTiO₃ catalyst during the exemplary peroxymonosulfate activation process using X-ray absorption spectroscopy and in situ Raman spectroscopy, revealing the substrate tuned its structural evolution, which is the reversible stretching vibration of O-Sr-O and Co/Ti-O bonds in different orientations. This process effectively promotes the generation of key SO₅* intermediates, which is beneficial to the formation of ¹O₂ and SO₄^•- from persulfate on the Co active site. Density functional theory and X-ray absorption spectroscopy show that the optimized structural distortion enhanced the metal-oxygen bond strength by tuning the e_g orbitals and increased the number of transferred electrons to peroxymonosulfate by about 3-fold, achieving excellent efficiency and stability in removing organic pollutants.

Oxygen vacancies-dominated reactive species generation from peroxymonosulfate activated by MoO3-x for pollutant degradation

Interface oxygen vacancies (OVs) are commonly used to improve the catalytic performance of activators in persulfate-based advanced oxidation processes, but the underlying mechanism was not fully explored. This work reports a facile heat treatment method to regulate OVs in MoO_3-x to elucidate the mechanism of peroxymonosulfate (PMS) activated by OVs to degrade 2,4,4-Trichlorobiphenyl (PCB28). Electron spin resonance, free radical quenching, X-ray photoelectron spectroscopy, and Raman spectroscopy confirmed that both reducing Mo species and OVs of MoO_3-x surface were responsible for PMS activation. Further experiments and Density Function Theory (DFT) calculation suggest that OVs in MoO_3-x induced the formation of superoxide radical (O₂^•-), and then O₂^•- was transformed into singlet oxygen (¹O₂) or mediated PMS activation to generate radicals, which contritbued to 70.2% of PCB28 degradation. The steady-state concentrations of free radical calculated with the kinetics model show that OVs were more favorable to mediate PMS to generate hydroxyl radicals (^•OH) under oxic conditions, while reducing Mo species would like to induce PMS to produce sulfate radicals (SO₄^•-). Overall, this study is dedicated to a new insight into the in-depth mechanism of PMS activation by OVs-rich catalysts and provides a novel strategy for reactive species regulation in PMS based oxidation process.

Selective activation of peroxymonosulfate govern by B-site metal in delafossite for efficient pollutants degradation: Pivotal role of d orbital electronic configuration

Radical and non-radical oxidation pathways have been universally validated in transition metals (TMs) oxides activated peroxymonosulfate (PMS) processes. However, achieving high efficiency and selectivity of PMS activation remains challenging due to the ambiguous tuning mechanism of TMs sites on PMS activation in thermodynamic scope. Herein, we demonstrated that the exclusive PMS oxidation pathways were regulated by d orbital electronic configuration of B-sites in delafossites (CuBO₂) for Orange I degradation (Co^III 3d⁶ for reactive oxygen species (ROSs) vs. Cr^III 3d³ for electron transfer pathway). The d orbital electronic configuration was identified to affect the orbital overlap extent between 3d of B-sites and O 2p of PMS, which induced B-sites offering different types of hybrid orbital to coordinate with O 2p of PMS, thereby forming the high-spin complex (CuCoO₂@PMS) or the low-spin complex (CuCrO₂@PMS), on which basis PMS was selectively dissociated to form ROSs or achieve electron transfer pathway. As indicated by thermodynamic analysis, a general rule was proposed that B-sites of less than half-filled 3d orbital tended to act as electron shuttle, i.e., Cr^III (3d³), Mn^III (3d⁴), interacting with PMS to execute an electron transfer pathway for degrading Orange I, while B-sites of between half-filled and full-filled 3d orbital preferred to be electron donator, i.e., Co^III (3d⁶), Fe^III (3d⁵), activating PMS to generate ROSs. These findings lay a foundation for the oriented design of TMs-based catalysts from the atomic level according to d orbital electronic configuration optimization, as so to facilitate the achievement of PMS-AOPs with highly selective and efficient remediation of contaminants in water purification practice.

B-doping mediated formation of oxygen vacancies in Bi2Sn2O7 quantum dots with a unique electronic structure for efficient and stable photoelectrocatalytic sulfamethazine degradation

This study devised a straightforward one-step approach that enabled simultaneous boron (B) doping and oxygen vacancies (OVs) production on Bi₂Sn₂O₇ (BSO) (B-BSO-OV) quantum dots (QDs), optimizing the electrical structure of the photoelectrodes. Under light-emitting diode (LED) illumination and a low potential of 1.15 V, B-BSO-OV demonstrated effective and stable photoelectrocatalytic (PEC) degradation of sulfamethazine (SMT), achieving the first-order kinetic rate constant of 0.158 min^-1. The surface electronic structure, the different factors influencing the PEC degradation of SMT, and the degradation mechanism were studied. Experimental studies have shown that B-BSO-OV exhibits strong visible light trapping ability, high electron transport ability, and superior PEC performance. DFT calculations show that the presence of OVs on BSO successfully reduces the band gap, controls the electrical structure, and accelerates charge transfer. This work sheds light on the synergistic effects of the electronic structure of B-doping and OVs in heterobimetallic oxide BSO under the PEC process and offers a promising approach for the design of photoelectrodes.

A critical review on correlating active sites, oxidative species and degradation routes with persulfate-based antibiotics oxidation

At present, numerous heterogeneous catalysts have been synthesized to activate persulfate (PS) and produce various reactive species for antibiotic degradation from water. However, the systematic summary of the correlation among catalyst active sites, PS activation pathway and pollutant degradation has not been reported. This review summarized the effect of metal-based, carbon-based and metal-carbon composite catalysts on the degradation of antibiotics by activating PS. Metal and non-metal sites are conducive to inducing different oxidation pathways (SO₄^•-, ^•OH radical oxidation and ¹O₂ oxidation, mediated electron transfer, surface-bound reactive complexes and high-valent metal oxidation). SO₄^•- and ^•OH are easy to attack CH, S-N, CN bonds, CC double bonds and amino groups in antibiotics. ¹O₂ is more selective to the structure of the aniline ring and amino group, and also to attacking CS, CN and CH bonds. Surface-bound active species can cleave CC, SN, CS and CN bonds. Other non-radical pathways may also induce different antibiotic degradation routes due to differences in oxidation potential and electronic properties. This critical review clarified the functions of active sites in producing different reactive species for selective oxidation of antibiotics via featured pathways. The outcomes will provide valuable guidance of oriented-regulation of active sites in heterogeneous catalysts to produce on-demand reactive species toward high-efficiency removing antibiotics from water.

The debatable role of singlet oxygen in persulfate-based advanced oxidation processes

Singlet oxygen (¹O₂) attracts much attention in persulfate-based advanced oxidation processes (PS-AOPs), because of its wide pH tolerance and high selectivity toward electron-rich organics. However, there are conflicts about the ¹O₂ role in PS-AOPs on several aspects, including the formation of different key reactive oxygen species (ROS) at similar active sites, pH dependence, broad-spectrum activity, and selectivity in the elimination of organic pollutants. To a large degree, these conflicts root in the drawbacks of the methods to identify and evaluate the role of ¹O₂. For example, the quenchers of ¹O₂ have high reactivity to other ROS and persulfate as well. In addition, electron transfer process (ETP) also selectively oxidizes organics, having a misleading effect on the identification of ¹O₂. Therefore, in this review, we summarized and discussed some basic properties of ¹O₂, the debatable role of ¹O₂ in PS-AOPs on multiple aspects, and the methods and their drawbacks to identify and evaluate the role of ¹O₂. On the whole, this review aims to better understand the role of ¹O₂ in PS-AOPs and further help with its reasonable utilization.

Electron donation of Fe-Mn biochar for chromium(VI) immobilization: Key roles of embedded zero-valent iron clusters within iron-manganese oxide

The dense surface passivation layer on zero-valent iron (ZVI) restricts its efficiency for water decontamination, causing a poor economy and waste of resources. Herein, we found that the ZVI on Fe-Mn biochar could afford a high electron-donating efficiency for the Cr(VI) reduction and immobilization. Over 78.0% of Fe in the Fe-Mn biochar was used for the Cr(VI) reduction and immobilization, i.e., 56.2 - 161.7 times higher than the commercial ZVI (0.5%) and modified ZVI (0.9 -1.3%), indicating that the unique ZVI species in Fe-Mn biochar offered an outstanding Fe utilization efficiency. We proposed that oxygen atoms in the FeO in the FeMnO₂ precursor were removed during pyrolysis with biochar while the MnO skeleton was preserved, forming the embedded ZVI clusters within Fe-Mn oxide. The unique structure inhibited the formation of the Fe-Cr complex on Fe(0), which would facilitate the electron transfer between core Fe(0) and Cr(VI). Moreover, the surface FeMnO₂ inhibited the diffusion of Fe and facilitated its affinity with pollutants, thus supporting higher efficiency for pollutant immobilization. The preserved performance of Fe-Mn biochar was proved in industrial wastewater and after long-term oxidation process, and the economic benefit was evaluated. This work provides a new approach for developing active ZVI-based materials with high Fe utilization efficiency and economics for water pollution control.

Applications of vacancy defect engineering in persulfate activation: Performance and internal mechanism

The vacancy defects in heterogeneous catalysts have received extensive attention for persulfate (PS) activation. Vacancy defects can tune the electronic structure of metal oxides and generate unsaturated coordination sites. Meanwhile, the adsorption energy of reactants on catalyst surface is optimized. Thereby, the reaction energy barrier between catalysts and PS decreases, which could promote catalytic activation and accelerate pollutants degradation. Nowadays, oxygen vacancy (OV), nitrogen vacancy (NV), sulfur vacancy (SV), selenium vacancy (SeV) and titanium vacancy (TiV) have been widely studied with great potential for water remediation. So far, no review was reported regarding the vacancy activated persulfate systems. This paper summarized the types, preparation, mechanism and applications of vacancy in PS systems systematically. In addition, we put forward possible development of vacancy engineering in PS activation systems. It is expected that this review will contribute to the controllable synthesis and applications of vacancies in catalysts for PS activation and contaminants removal.

Deciphering the photoactive species-directed antibacterial mechanism of bismuth oxychloride with modulated nanoscale thickness

As an environmentally benign disinfection strategy, photocatalytic bacterial inactivation using nanoparticles involves photogenerated reactive species that cause cellular oxidative stress. Rationalising the structural performance of photocatalysts for the practical uses such as wastewater treatment has attracted significant attention; however, the contribution of reactive species to their photocatalytic antibacterial activities at the molecular and transcriptomic levels remains unclear. In this study, nontoxic bismuth oxychloride (BiOCl) photocatalysts with different nanoscale thicknesses, including nanosheets (Ns, ∼5.4 nm), nanoplates (Np, ∼1.8 nm), and ultra-nanosheets (Uns, ∼1.1 nm), were synthesised under hydrothermal conditions. Among the three samples, BiOCl Uns exhibited the most effective photocatalytic degradation efficiency with the calculated apparent rate constant of 0.0294 min^-1, ∼4 times faster than that of Ns, whereas BiOCl Ns possessed the most pronounced bactericidal effect (5.4 log inactivation). Such findings indicate the distinct role of the photoactive species responsible for photocatalytic bacterial inactivation. Moreover, transcriptome analysis of Escherichia coli after photocatalytic treatment revealed that the underlying photocatalytic antibacterial mechanism at the genetic expression level involves cellular component biosynthesis, energy metabolism, and material transportation. Notably, the differences between BiOCl Ns and BiOCl Uns were significantly enriched in purine metabolism. Therefore, the cost-effective preparation of BiOCl nanosheets with nanoscale thickness-modulated photocatalytic antibacterial activity has remarkable potential for sustainable environmental and biomedical applications.

Metal ion endogenous cycles of CoFe2O4-x induced boosted photocatalytic/PMS degradation toward polycyclic aromatic hydrocarbons

The rational design of photocatalytic nanomaterials with unique structures is critical for remediating environmental problems and thus reducing ecological risks. In this work, we employed H₂ temperature-programmed reduction to modify MFe₂O₄ (M = Co, Cu, and Zn) photocatalysts for obtaining additional oxygen vacancies. After activation of PMS, naphthalene and phenanthrene degradation rates in the soil phase were increased by 3.24-fold and 1.39-fold, respectively, and 1.38-fold for naphthalene in the aqueous phase by H-CoFe₂O_4-x. The extraordinary photocatalytic activity is attributed to the oxygen vacancies on the H-CoFe₂O_4-x surface, which promote electron transfer and thus enhance the redox cycle from Co(III)/Fe(III) to Co(II)/Fe(II). In addition, oxygen vacancies are used as electron traps to hinder the recombination of photogenerated carriers and accelerate the generation of hydroxyl and superoxide radicals. Quenching tests showed that the addition of p-benzoquinone resulted in the greatest decrease in the degradation rate of naphthalene (inhibition of about 85.5%), demonstrating that O₂˙^- radicals are the main active species in the photocatalytic degradation of naphthalene. H-CoFe₂O_4-x showed improved degradation performance in synergy with PMS (82.0%, k_app = 0.00714 min^-1) while maintaining excellent stability and reusability. Hence, this work provides a promising approach for the design of efficient photocatalysts to degrade persistent organic pollutants in soil and aqueous environments.

Unveiling different antibiotic degradation mechanisms on dual reaction center catalysts with nitrogen vacancies via peroxymonosulfate activation

Metal-nitrogen-site catalysts are widely recognized as effective heterogeneous catalysts in peroxymonosulfate (PMS)-based advanced oxidation processes. However, the selective oxidation mechanism for organic pollutants is still contradictory. In this work, manganese-nitrogen active centers and tunable nitrogen vacancies were synchronously constructed on graphitic carbon nitride (LMCN) through l-cysteine-assisted thermal polymerization to reveal different antibiotic degradation mechanisms. Benefiting from the synergism of manganese-nitrogen bond and nitrogen vacancies, the LMCN catalyst exhibited excellent catalytic activity for the degradation of tetracycline (TC) and sulfamethoxazole (SMX) antibiotics with first-order kinetic rate constants of 0.136 min^-1 and 0.047 min^-1, which were higher than those of other catalysts. Electron transfer dominated TC degradation at low redox potentials, while electron transfer and high-valent manganese (Mn (V)) were responsible for SMX degradation at high redox potentials. Further experimental studies unveiled that the pivotal role of nitrogen vacancies is to promote electron transfer pathway and Mn(V) generation, while nitrogen-coordinated manganese as the primary catalytic active site determines Mn(V) generation. In addition, the antibiotic degradation pathways were proposed and the toxicity of byproducts was analyzed. This work provides an inspiring idea for the controlled generation of reactive oxygen species by targeted activation of PMS.

UV/Fe(II)/S(IV) Pretreatment for Ultrafiltration of Microcystis aeruginosa-Laden Water: Fe(II)/Fe(III) Triggered Synergistic Oxidation and Coagulation

Ultrafiltration (UF) has been proven effective in removing algae during seasonal algal blooms, but the algal cells and the metabolites can induce severe membrane fouling, which undermines the performance and stability of the UF. Ultraviolet-activated sulfite with iron (UV/Fe(II)/S(IV)) could enable an oxidation-reduction coupling circulation and exert synergistic effects of moderate oxidation and coagulation, which would be highly preferred in fouling control. For the first time, the UV/Fe(II)/S(IV) was systematically investigated as a pretreatment of UF for treating Microcystis aeruginosa-laden water. The results showed that the UV/Fe(II)/S(IV) pretreatment significantly improved the removal of organic matter and alleviated membrane fouling. Specifically, the organic matter removal increased by 32.1% and 66.6% with UV/Fe(II)/S(IV) pretreatment for UF of extracellular organic matter (EOM) solution and algae-laden water, respectively, while the final normalized flux increased by 12.0-29.0%, and reversible fouling was mitigated by 35.3-72.5%. The oxysulfur radicals generated in the UV/S(IV) degraded the organic matter and ruptured the algal cells, and the low-molecular-weight organic matter generated in the oxidation penetrated the UF and deteriorated the effluent. The over-oxidation did not happen in the UV/Fe(II)/S(IV) pretreatment, which may be attributed to the cyclic redox Fe(II)/Fe(III) coagulation triggered by the Fe(II). The UV-activated sulfate radicals in the UV/Fe(II)/S(IV) enabled satisfactory organic removal and fouling control without over-oxidation and effluent deterioration. The UV/Fe(II)/S(IV) promoted the aggregation of algal foulants and postponed the shift of the fouling mechanisms from standard pore blocking to cake filtration. The UV/Fe(II)/S(IV) pretreatment proved effective in enhancing the UF for algae-laden water treatment.

A novel heterogeneous catalytic system (AC/ZVI/CaO2) promotes simultaneous removal of phosphate and sulfamethazine: Performance, mechanism and application feasibility verification

The eutrophication and pharmaceutical residue are the key issues to the treatment of rural non-point source pollution, concerning risks to aquatic ecosystems and human health. In this study, a novel activated carbon/zero-valent iron/calcium peroxide (AC/ZVI/CaO₂) catalytic system was constructed to remove simultaneously typical rural non-point source pollutants: phosphate and sulfamethazine (SMZ). The optimal mass ratio of the system was determined as 20% AC, 48% ZVI and 32% CaO₂. It was shown that the removal efficiency of phosphorus (P) and SMZ exceeded 65% and 40% in pH 2-11, respectively. It worked well in the presence of typical anions and humic acid. The mechanistic analyses for P removal indicated that AC/ZVI/CaO₂ system can effectively load P by the formation of crystalline state Ca-P species and Fe-P/Ca-P amorphous state coprecipitates under neutral and acidic conditions, respectively. The presence of AC in AC/ZVI/CaO₂ system could form iron-carbon micro-electrolysis process for accelerating Fenton reaction in acidic environment. And AC also can produce reactive oxygen species for the SMZ degradation by relying on persistent free radicals/graphitic carbon catalysis under environmental condition. In addition, we developed a low-impact development stormwater filter for application feasibility verification of the system. Feasibility analysis showed that the system could save up to ∼50% cost in contrast with the price of Phoslock (a commercial P load product) and presented advantages of non-toxicity, long-acting, stability and the potential to promote biodegradation by provision of aerobic environment.

The optimized Fenton-like activity of Fe single-atom sites by Fe atomic clusters-mediated electronic configuration modulation

The performance optimization of isolated atomically dispersed metal active sites is critical but challenging. Here, TiO2@Fe species-N-C catalysts with Fe atomic clusters (ACs) and satellite Fe-N4 active sites were fabricated to initiate peroxymonosulfate (PMS) oxidation reaction. The AC-induced charge redistribution of single atoms (SAs) was verified, thus strengthening the interaction between SAs and PMS. In detail, the incorporation of ACs optimized the HSO5- oxidation and SO5·- desorption steps, accelerating the reaction progress. As a result, the Vis/TiFeAS/PMS system rapidly eliminated 90.81% of 45 mg/L tetracycline (TC) in 10 min. The reaction process characterization suggested that PMS as an electron donor would transfer electron to Fe species in TiFeAS, generating 1O2. Subsequently, the hVB+ can induce the generation of electron-deficient Fe species, promoting the reaction circulation. This work provides a strategy to construct catalysts with multiple atom assembly-enabled composite active sites for high-efficiency PMS-based advanced oxidation processes (AOPs).

FeMoS2 micoroparticles as an excellent catalyst for the activation of peroxymonosulfate toward organic contaminant degradation

The FeMoS₂ catalyst for activating peroxymonosulfate (PMS) is a promising pathway for removing organic pollutants in wastewater, however, the dominant FeS₂ phases and sulfur (S) vacancies in it are little involved. Herein, for the first time, novel bimetallic FeMoS₂ microparticles were synthesized by a simple method and then applied for PMS activation for degrading organic pollutants. The catalysts were characterized by several techniques, including X-ray diffraction and X-ray photoelectron spectroscopies. The results revealed that new FeMoS₂ microparticles containing S vacancies in the main FeS₂ phases were obtained. FeS₂ and S vacancies were found to play important roles for activating PMS by radical and nonradical pathways. More Fe²⁺ and Mo⁴⁺ were formed in the presence of S vacancies, which offered a new strategy for exploring novel heterogeneous catalysts in the activation of PMS for environmental remediation.

Enhanced Interfacial Electron Transfer by Asymmetric Cu-Ov -In Sites on In2 O3 for Efficient Peroxymonosulfate Activation

Enhancing the peroxymonosulfate (PMS) activation efficiency to generate more radicals is vital to promote the Fenton-like reaction activity, however, how to promote the PMS adsorption and accelerate the interfacial electron transfer to boost its activation kinetics remains a great challenge. Herein, we prepared Cu-doped defect-rich In₂ O₃ (Cu-In₂ O₃ /O_v ) catalysts containing asymmetric Cu-O_v -In sites for PMS activation in water purification. The intrinsic catalytic activity is that the side-on adsorption configuration of the O-O bond (Cu-O-O-In) at the Cu-O_v -In sites significantly stretches the O-O bond length. Meanwhile, the Cu-O_v -In sites increase the electron density near the Fermi energy level, promoting more and faster electron transfer to the O-O bond for generating more SO₄ ⋅^- and ⋅OH. The degradation rate constant of tetracycline achieved by Cu-In₂ O₃ /O_v is 31.8 times faster than In₂ O₃ /O_v , and it shows the possibility of membrane reactor for practical wastewater treatment.

Pretreatment of membrane dye wastewater by CoFe-LDH-activated peroxymonosulfate: Performance, degradation pathway, and mechanism

When a membrane is used to treat dye wastewater, dye molecules are continually concentrated at the membrane surface over time, resulting in a dramatic decrease in membrane flux. Aside from routine membrane cleaning, the pretreatment of dye wastewater to degrade organic pollutants into tiny molecules is a facile solution to the problem. In this study, the use of layered double hydroxide (LDH) to activate peroxymonosulfate (PMS) for efficient degradation of organic pollutant has been thoroughly investigated. We utilized a simple two-drop co-precipitation process to prepare CoFe-LDH. The transition metal components in CoFe-LDH effectively activate PMS to create oxidative free radicals, and the layered structure of LDH increases the number of active sites, and thereby considerably enhancing the reaction rate. It was found that the reaction process produced non-free and free radicals, including singlet oxygen (¹O₂), sulfate radicals (SO₄^•-), and hydroxyl radicals (•OH), with ¹O₂ being the dominant reactive species. Under the optimal conditions (pH 6.7, PMS dosage 0.2 g/L, catalyst loading 0.1 g/L), the degradation of Acid Red 27 dye in the CoFe-LDH/PMS system reached 96.7% within 15 min at an initial concentration of 200 mg/L. The CoFe-LDH/PMS system also exhibited strong resistance to inorganic ions and pH during the degradation of organic pollutants. This study presents a novel strategy for the synergistic treatment of dye wastewater with free and non-free radicals produced by LDH-activated PMS in a natural environment.

Low Concentration of Peroxymonosulfate Triggers Dissolved Oxygen Conversion over Single Atomic Fe-N3 O1 Sites for Water Decontamination

Achieving satisfactory organic pollutant oxidation with a low concentration of peroxymonosulfate (PMS) is vital for persulfate-involved advanced oxidation processes to reduce resource consumption and avoid excessive sulfate anion (SO₄ ^2- ) production. Herein, efficient conversion of dissolved oxygen (DO) over single-atomic Fe-N₃ O₁ sites anchored on carbon nitride for efficient contaminant degradation is fulfilled, triggered by a low concentration of PMS (0.2 mm). Experimental and theoretical results reveal that the preferentially adsorbed PMS onto atomic Fe-N₃ O₁ center can deliver electrons toward the single Fe atom to increase its electron density to trigger DO reduction into superoxide radical (O₂ ^• - ) and successive transformation into singlet oxygen (¹ O₂ ), which is quite different from the conventional PMS activation process mostly depending on PMS itself function for reactive oxygen species generation. On the other hand, PMS with high concentration could occupy active Fe-N₃ O₁ sites to hamper DO conversion and further produce massive SO₄ ^2- . A couple of -Fe-CN_0.05 -and slight PMS is effective for actual kitchen wastewater remediation and long-term bisphenol A degradation. This work elucidates the triggering role of low-concentration PMS in DO conversion over a single-atom Fe catalyst, which can inspire the development of resource-saving, cost-effective, and environmentally-friendly catalytic oxidation systems for environmental restoration.

Highly efficient activation of peroxymonosulfate by biomass juncus derived carbon decorated with cobalt nanoparticles for the degradation of ofloxacin

The cobalt nanoparticles decorated biomass Juncus derived carbon (Co@JDC) was prepared by facile calcination strategy and applied to activate peroxymonosulfate (PMS) for eliminating ofloxacin (OFX) in the water environment. The results of catalytic experiments show that 97% of OFX degradation efficiency and 70.4% of chemical oxygen demand removal rate are obtained within 24 min at 0.1 g L^-1 Co@JDC, 0.2 g L^-1 PMS, 20 mg L^-1 OFX (100 mL), and pH = 7, which indicates that Co@JDC/PMS system exhibits excellent performance. Meanwhile, the experimental results of affect factor show that Co@JDC/PMS system can operate in a wider pH range (3-9) and Cl^-1, NO₃^-1, and SO₄^2- have an ignorable effect on OFX degradation. The radical identification experiments confirm that SO₄˙^-, ·OH, O₂˙^-, and ¹O₂ are involved in the process of PMS activation, especially SO₄˙^- and ¹O₂ are the main contributors. Furthermore, a possible PMS activation mechanism by Co@JDC was proposed and the degradation pathways of OFX were deduced. Finally, the stable catalytic activity, negligible leaching of Co²⁺, and the outstanding degradation efficiency for other antibiotics prove that Co@JDC possesses good stability and universality.

Unraveling spongy Co3O4 mediated activation of peroxymonosulfate: Overlooked involvement of instantaneously produced high-valent-cobalt-oxo

Peroxymonosulfate (PMS) activation induced by tricobalt tetroxide spinel (Co₃O₄) has been confirmed as a typical Haber-Weiss reaction, while free radicals were once considered as the dominated reactive species in the previous studies. However, the catalytic mechanism of the spongy Co₃O₄ driven PMS activation was surprisingly found as a radical/nonradical mixed process rather than a pure radical process in the present work. The important role of sulfate radical (SO₄^-) was confirmed through the quenching experiments. Despite the inhibition of furfuryl alcohol (FFA) and 1,4-benzoquinone (BQ) on degradation was generally accepted as the evidence to support the existence of ¹O₂ and O₂^-, additional experiments using methyl phenyl sulfoxide (PMSO) as the indicator indeed verified high-valent-cobalt-oxo rather than ¹O₂ and O₂^- dominated the very early reaction stage. Notably, instead of homogeneous Co³⁺, heterogeneous Co(IV) = O on catalyst surface was believed to be responsible for the oxidation of organics. Spongy Co₃O₄ not only possessed stronger catalytic ability than commercial Co₃O₄ (k_{[spongy Co3O4]} = 0.74 min^-1, k_[Co3O4] = 0.08 min^-1), but also owned preferable stability. The performance of catalytic system was barely affected by the solution pH under the near neutral condition. Besides, little suppression of the widely existing anions on the degradation indicated the potential application of spongy Co₃O₄/PMS system. This study provides a reliable oxidation technology for the removal of organic pollutants, and sheds new light on the cobalt oxide triggered PMS activation process.