Polymethylmethacrylate bone cements and additives: A review of the literature

Patient-specific PEEK implants for immediate restoration of temporal fossa after maxillary reconstruction with temporalis muscle flap

BACKGROUND

Temporal hollowing is a common complication following the rotation of the temporalis muscle that leaves the patient with a cosmetic impairment. Several alloplastic materials have been used to reconstruct the donor site; however, these implants need meticulous adaptation to conform the periphery of the defect and restore the contour of the temporal area. The aim of this study was to assess the use of patient-specific polyetheretherketone (PEEK) temporal implants to prevent temporal hollowing following the use of full temporalis muscle flap for large maxillary defects reconstruction.

METHODS

This was a prospective study conducted on eight patients with major maxillary defects indicating the need of reconstruction with full temporalis muscle flap or any lesion indicating major maxillary resection and immediate reconstruction with total temporalis muscle flap. For each patient, a patient-specific PEEK implant was fabricated using virtual planning and milled from PEEK blocks. In the surgical theater, the temporalis muscle was exposed, elevated, and transferred to the maxilla. After the temporalis muscle transfer, PEEK implants were fixed in place to prevent temporal hollowing.

RESULTS

The surgical procedures were uneventful for all patients. The esthetic result was satisfactory with no post-operative complications except in one patient where seroma occurred after 2 weeks and resolved after serial aspiration.

CONCLUSION

Patient-specific PEEK implant appears to facilitate the surgical procedures eliminate several meticulous steps that are mainly based on the surgeon's experience.

TRIAL REGISTRATION

Clinical trials registration: NCT05240963 .

Characterisation of Selected Materials in Medical Applications

Tissue engineering is an interdisciplinary field of science that has developed very intensively in recent years. The first part of this review describes materials with medical and dental applications from the following groups: metals, polymers, ceramics, and composites. Both positive and negative sides of their application are presented from the point of view of medical application and mechanical properties. A variety of techniques for the manufacture of biomedical components are presented in this review. The main focus of this work is on additive manufacturing and 3D printing, as these modern techniques have been evaluated to be the best methods for the manufacture of medical and dental devices. The second part presents devices for skull bone reconstruction. The materials from which they are made and the possibilities offered by 3D printing in this field are also described. The last part concerns dental transitional implants (scaffolds) for guided bone regeneration, focusing on polylactide-hydroxyapatite nanocomposite due to its unique properties. This section summarises the current knowledge of scaffolds, focusing on the material, mechanical and biological requirements, the effects of these devices on the human body, and their great potential for applications.

Customized cost-effective polymethylmethacrylate cranioplasty: a cosmetic comparison with other low-cost methods of cranioplasty

BACKGROUND

Intraoperative hand-moulded cranioplasty and polymethylmethacrylate (PMMA) prostheses made from bone impressions are economical but the cosmetic results are less than satisfactory. Commercially available customized prostheses perform better but are prohibitively expensive. We evaluate the performance of a locally developed, low-cost customized PMMA cranioplasty prosthesis.

OBJECTIVE

To compare the cosmetic outcome of 3 types of PMMA cranioplasty as well as with objective measurements on postoperative CT scans METHODS: This study includes 70 patients who underwent cranioplasty between March 2016 and June 2020. In this period, patients had their cranioplasty prostheses made by intra-operative hand moulding (HM), by using the removed bone as a template and making a bone impression (BI) or by 3D printing the prosthesis based on a CT scan. Cosmetic outcomes were assessed by the patient and the operating surgeon on an 8-point scale. The degree of measured anthropometric asymmetry was measured on a postoperative CT scan and correlated with the cosmetic outcome.

RESULTS

Our locally produced 3D-printed cranioplasty prostheses showed a statistically better performance in cosmetic scores when compared to the HM and BI (p value < 0.001). CT anthropometric measurements significantly correlated with cosmetic outcome (p value 0.01) CONCLUSION: Our 3D cranioplasty prostheses had better cosmetic outcomes than HM and BI prostheses, and our technique is able to produce them at 10% of the cost of the currently available commercial customized prostheses.

Role of Implantable Drug Delivery Devices with Dual Platform Capabilities in the Prevention and Treatment of Bacterial Osteomyelitis

As medicine advances and physicians are able to provide patients with innovative solutions, including placement of temporary or permanent medical devices that drastically improve quality of life of the patient, there is the persistent, recurring problem of chronic bacterial infection, including osteomyelitis. Osteomyelitis can manifest as a result of traumatic or contaminated wounds or implant-associated infections. This bacterial infection can persist as a result of inadequate treatment regimens or the presence of biofilm on implanted medical devices. One strategy to mitigate these concerns is the use of implantable medical devices that simultaneously act as local drug delivery devices (DDDs). This classification of device has the potential to prevent or aid in clearing chronic bacterial infection by delivering effective doses of antibiotics to the area of interest and can be engineered to simultaneously aid in tissue regeneration. This review will provide a background on bacterial infection and current therapies as well as current and prospective implantable DDDs, with a particular emphasis on local DDDs to combat bacterial osteomyelitis.

Preparation and Characterization of an Injectable and Photo-Responsive Chitosan Methacrylate/Graphene Oxide Hydrogel: Potential Applications in Bone Tissue Adhesion and Repair

As life expectancy continues to increase, the inevitable weakening and rupture of bone tissue have grown as concerns in the medical community, thus leading to the need for adhesive materials suitable for bone repair applications. However, current commercially available adhesives face certain drawbacks that prevent proper tissue repair, such as low biocompatibility, poor adhesion to wet surfaces, and the need for high polymerization temperatures. This work aims to develop an injectable and photo-responsive chitosan methacrylate/graphene oxide (ChiMA/GO) adhesive nanocomposite hydrogel of high biocompatibility that is easy to apply by simple extrusion and that offers the possibility for in situ polymer and physiological temperatures. The nanocomposite was thoroughly characterized spectroscopically, microscopically, rheologically, thermally, and through mechanical, textural, and biological assays to fully evaluate its correct synthesis and functionalization and its performance under physiological conditions that mimic those observed in vivo. In addition, a finite element analysis (FEA) simulation was used to evaluate its performance in femur fractures. Results suggest the material’s potential as a bioadhesive, as it can polymerize at room temperature, shows superior stability in physiological media, and is capable of withstanding loads from body weight and movement. Moreover, the material showed remarkable biocompatibility as evidenced by low hemolytic and intermediate platelet aggregation tendencies, and high cytocompatibility when in contact with osteoblasts. The comprehensive studies presented here strongly suggest that the developed hydrogels are promising alternatives to conventional bone adhesives that might be further tested in vivo in the near future.

Evaluation of a self-fitting, shape memory polymer scaffold in a rabbit calvarial defect model

Self-fitting scaffolds prepared from biodegradable poly(ε-caprolactone)-diacrylate (PCL-DA) have been developed for the treatment of craniomaxillofacial (CMF) bone defects. As a thermoresponsive shape memory polymer (SMP), with the mere exposure to warm saline, these porous scaffolds achieve a conformal fit in defects. This behavior was expected to be advantageous to osseointegration and thus bone healing. Herein, for an initial assessment of their regenerative potential, a pilot in vivo study was performed using a rabbit calvarial defect model. Exogenous growth factors and cells were excluded from the scaffolds. Key scaffold material properties were confirmed to be maintained following gamma sterilization. To assess scaffold integration and neotissue infiltration along the defect perimeter, non-critically sized (d = 8 mm) bilateral calvarial defects were created in 12 New Zealand white rabbits. Bone formation was assessed at 4 and 16 weeks using histological analysis and micro-CT, comparing defects treated with an SMP scaffold (d = 9 mm x t = 1 or 2 mm) to untreated defects (i.e. defects able to heal without intervention). To further assess osseointegration, push-out tests were performed at 16 weeks and compared to defects treated with poly(ether ether ketone) (PEEK) discs (d = 8.5 mm x t = 2 mm). The results of this study confirmed that the SMP scaffolds were biocompatible and highly conducive to bone formation and ingrowth at the perimeter. Ultimately, this resulted in similar bone volume and surface area versus untreated defects and superior performance in push-out testing versus defects treated with PEEK discs. STATEMENT OF SIGNIFICANCE: Current treatments of craniomaxillofacial (CMF) bone defects include biologic and synthetic grafts but they are limited in their ability to form good contact with adjacent tissue. A regenerative engineering approach using a biologic-free scaffold able to achieve conformal fitting represents a potential "off-the-shelf" surgical product to heal CMF bone defects. Having not yet been evaluated in vivo, this study provided the preliminary assessment of the bone healing potential of self-fitting PCL scaffolds using a rabbit calvarial defect model. The study was designed to assess scaffold biocompatibility as well as bone formation and ingrowth using histology, micro-CT, and biomechanical push-out tests. The favorable results provide a basis to pursue establishing self-fitting scaffolds as a treatment option for CMF defects.

Cytocompatibility of Polymethyl Methacrylate Honeycomb-like Pattern on Perfluorinated Polymer

In this study, we present a simple approach for developing a biocompatible polymer scaffold with a honeycomb-like micropattern. We aimed to combine a plasma treatment of fluorinated ethylene propylene (FEP) substrate with an improved phase separation technique. The plasma exposure served for modification of the polymer surface properties, such as roughness, surface chemistry, and wettability. The treated FEP substrate was applied for the growth of a honeycomb-like pattern from a solution of polymethyl methacrylate (PMMA). The properties of the pattern were strongly dependent on the conditions of plasma exposure of the FEP substrate. The physico-chemical properties of the prepared pattern, such as changes in wettability, aging, morphology, and surface chemistry, were determined. Further, we have examined the cellular response of human osteoblasts (U-2 OS) on the modified substrates. The micropattern prepared with a selected combination of surface activation and amount of PMMA for honeycomb construction showed a positive effect on U-2 OS cell adhesion and proliferation. Samples with higher PMMA content (3 and 4 g) formed more periodic hexagonal structures on the surface compared to its lower amount (1 and 2 g), which led to a significant increase in the pattern cytocompatibility compared to pristine or plasma-treated FEP.

Optimization of the Mechanical Properties and the Cytocompatibility for the PMMA Nanocomposites Reinforced with the Hydroxyapatite Nanofibers and the Magnesium Phosphate Nanosheets

Commercial poly methyl methacrylate (PMMA)-based cement is currently used in the field of orthopedics. However, it suffers from lack of bioactivity, mechanical weakness, and monomer toxicity. In this study, a PMMA-based cement nanocomposite reinforced with hydroxyapatite (HA) nanofibers and two-dimensional (2D) magnesium phosphate MgP nanosheets was synthesized and optimized in terms of mechanical property and cytocompatibility. The HA nanofibers and the MgP nanosheets were synthesized using a hydrothermal homogeneous precipitation method and tuning the crystallization of the sodium-magnesium-phosphate ternary system, respectively. Compressive strength and MTT assay tests were conducted to evaluate the mechanical property and the cytocompatibility of the PMMA-HA-MgP nanocomposites prepared at different ratios of HA and MgP. To optimize the developed nanocomposites, the standard response surface methodology (RSM) design known as the central composite design (CCD) was employed. Two regression models generated by CCD were analyzed and compared with the experimental results, and good agreement was observed. Statistical analysis revealed the significance of both factors, namely, the HA nanofibers and the MgP nanosheets, in improving the compressive strength and cell viability of the PMMA-MgP-HA nanocomposite. Finally, it was demonstrated that the HA nanofibers of 7.5% wt and the MgP nanosheets of 6.12% wt result in the PMMA-HA-MgP nanocomposite with the optimum compressive strength and cell viability.

Adsorption and wettability of extended anionic surfactants with different PO numbers on a polymethylmethacrylate surface

To investigate the effect of the number of propylene oxide (PO) units on the wettability of surfactants, the wettability of isomeric dodecyl(polyoxyisopropyl)7 sulfate (S-C12PO7S) and isomeric dodecyl(polyoxyisopropyl)13 sulfate (S-C12PO13S) on the surface of polymethylmethacrylate (PMMA) was investigated. The adsorption behavior on the PMMA surface was analyzed by measuring the surface tension and the contact angle. It is found that the PO group may form hydrogen bonds with the PMMA surface, thus facilitating the hydrophobic tails pointing to the aqueous phase. Moreover, the steric effect of the PO group benefits the formation of semi-micelles above the critical micelle concentration (CMC). Surfactant molecules adsorb on the PMMA surface by polar adsorption below the CMC with hydrophobic tails towards the water. Therefore, the PMMA surface is modified to be more hydrophobic. However, the sodium dodecyl sulfate (SDS) surfactant with no PO unit does not have hydrophobic modification ability on the PMMA surface. Below the CMC, the adsorption amounts of the S-C12PO7S and S-C12PO13S surfactants at the solid-liquid interface were approximately 1/3 of those at the air-liquid interface. Interestingly, the adsorption behavior changes when the concentration of the surfactants is around the CMC. The hydrophilic heads of the surfactant molecules will point to water, and the surfactant molecules will form semi-micellar aggregates on the PMMA surface. Therefore, the PMMA surface is modified to be hydrophilic above the CMC. What's more, both the hydrophilic modification ability and hydrophobic modification ability of the S-C12PO13S surfactant are stronger than those of the S-C12PO7S surfactant. This means that the number of PO units will affect the wettability ability of the surfactants. Therefore, the S-C12PO13S surfactant possesses smaller contact angles than the S-C12PO7S surfactant at high concentrations.

Layered Double Hydroxide Modified Bone Cement Promoting Osseointegration via Multiple Osteogenic Signal Pathways

Poly(methyl methacrylate) (PMMA) bone cement has been widely used in orthopedic surgeries including total hip/knee replacement, vertebral compression fracture treatment, and bone defect filling. However, aseptic loosening of the interface between PMMA bone cement and bone often leads to failure. Hence, the development of modified PMMA that facilitates the growth of bone into the modified PMMA bone cement is key to reducing the incidence of aseptic loosening. In this study, MgAl-layered double hydroxide (LDH) microsheets modified PMMA (PMMA&LDH) bone cement with superior osseointegration performance has been synthesized. The maximum polymerization reaction temperature of PMMA&LDH decreased by 7.0 and 11.8 °C, respectively, compared with that of PMMA and PMMA&COL-I (mineralized collagen I modified PMMA). The mechanical performance of PMMA&LDH decreased slightly in comparison with PMMA, which is beneficial to alleviate stress-shielding osteolysis, and indirectly promote osseointegration. The superior osteogenic ability of PMMA&LDH has been demonstrated in vivo, which boosts bone growth by 2.17- and 18.34-fold increments compared to the PMMA&COL-I and PMMA groups at 2 months, postoperatively. Moreover, transcriptome sequencing revealed four key osteogenic pathways: p38 MAPK, ERK/MAPK, FGF, and TGF-β, which were further confirmed by IPA, qPCR, and Western blot assays. Hence, LDH-modified PMMA bone cement is a promising biomaterial to enhance bone growth with potential applications in relevant orthopedic surgeries.

Functionalization of Synthetic Bone Substitutes

Bone substitutes have been applied to treat osseous defects for a long time. To prevent implant related infection (IRI) and enhance bone healing functionalized biomaterials, antibiotics and osteoinductive substances have been introduced. This study gives an overview of the current available surface-coated bone substitutes and provides an outlook for future perspectives.

2D phosphorene nanosheets, quantum dots, nanoribbons: synthesis and biomedical applications

Phosphorene, also known as black phosphorus (BP), is a two-dimensional (2D) material that has gained significant attention in several areas of current research. Its unique properties such as outstanding surface activity, an adjustable bandgap width, favorable on/off current ratios, infrared-light responsiveness, good biocompatibility, and fast biodegradation differentiate this material from other two-dimensional materials. The application of BP in the biomedical field has been rapidly emerging over the past few years. This article aimed to provide a comprehensive review of the recent progress on the unique properties and extensive medical applications for BP in bone, nerve, skin, kidney, cancer, and biosensing related treatment. The details of applications of BP in these fields were summarized and discussed.

New bone cements with Pluronic®F127 for prophylaxis and treatment of periprosthetic joint infections

In line with the increase in orthopedic prosthetic surgeries, there has been a significant rise in periprosthetic joint infections (PJI) due to Methicillin-Resistant Staphylococcus Aureus (MRSA) bacteria. In case of infection, antibiotic-added spacers are temporarily placed into the periprosthetic region. With the release of antibiotics usually failing to work in fighting off infection, recent studies have centered around developing more effective approaches. New polymethylmethacrylate (PMMA) cement mixtures were prepared for this study with Pluronic®F127, bicarbonate, and citric acid addition. Optimal solutions were searched by monitoring vancomycin release on consecutive days with HPLC in in-vitro. The strengths of the samples were measured via four-point bending tests. Compared to conventional PMMA, strength values were observed to have improved by about 20% with 1.0 g of Pluronic®F127. According to HPLC studies, the highest increase for the area under the curve value was obtained for Pluronic®F127 doped mixture with a value of about 20%. It is understood from SEM and BET studies that addition of Pluronic®F127 helps increase porosity. The present study concludes that the optimum concentration of Pluronic®F127 could improve the strength and drug-releasing capacity of the spacer by increasing its porosity.

Green synthesised silver nanoparticles incorporated electrospun poly(methyl methacrylate) nanofibers with different architectures for ophthalmologic alternatives

Silver nanoparticles with 5–10 nm diameters are synthesised using Couroupita guianensis flower extract. The synthesised silver nanoparticles found to show good antimicrobial activity against gram negative and gram positive bacteria. Poly(methyl methacrylate) nanofibers with pristine, surface roughened and coaxial hollow forms are prepared by electrospinning. The structural and morphological properties of these pure and structurally modified poly(methyl methacrylate) nanofibers are evidenced by various analytical techniques. The antimicrobial studies of poly(methyl methacrylate) nanofibers having different architectures incorporated with silver nanoparticles are carried out. It is found that, all the three forms of poly(methyl methacrylate) nanofibers incorporated with silver nanoparticles show antibacterial properties against both gram positive and gram negative bacteria. Among these, surface roughened poly(methyl methacrylate) nanofibers incorporated with silver nanoparticles show highest antibacterial activity than the other two structural forms. The present study offers an alternative to the existing optical lenses. People especially those who suffer from eye problems can protect their eyes in a better way from infectious agents by wearing optical lens made from C. guianensis stabilised silver nanoparticles incorporated poly(methyl methacrylate) nanofibers than that made from pure poly(methyl methacrylate) nanofibers or films.

Bone cement as a local chemotherapeutic drug delivery carrier in orthopedic oncology: A review

Metastatic bone lesions are common among patients with advanced cancers. While chemotherapy and radiotherapy may be prescribed immediately after diagnosis, the majority of severe metastatic bone lesions are treated by reconstructive surgery, which, in some cases, is followed by postoperative radiotherapy or chemotherapy. However, despite recent advancements in orthopedic surgery, patients undergoing reconstruction still have the risk of developing severe complications such as tumor recurrence and reconstruction failure. This has led to the introduction and evaluation of poly (methyl methacrylate) and inorganic bone cements as local carriers for chemotherapeutic drugs (usually, antineoplastic drugs (ANPDs)). The present work is a critical review of the literature on the potential use of these cements in orthopedic oncology. While several studies have demonstrated the benefits of providing high local drug concentrations while minimizing systemic side effects, only six studies have been conducted to assess the local toxic effect of these drug-loaded cements and they all reported negative effects on healthy bone structure. These findings do not close the door on chemotherapeutic bone cements; rather, they should assist in materials selection when designing future materials for the treatment of metastatic bone disease.

Controlling Antibiotic Release from Polymethylmethacrylate Bone Cement

Bone cement is used as a mortar for securing bone implants, as bone void fillers or as spacers in orthopaedic surgery. Antibiotic-loaded bone cements (ALBCs) have been used to prevent and treat prosthetic joint infections by providing a high antibiotic concentration around the implanted prosthesis. High antibiotic concentrations are, on the other hand, often associated with tissue toxicity. Controlling antibiotic release from ALBCS is key to achieving effective infection control and promoting prosthesis integration with the surrounding bone tissue. However, current ALBCs still need significant improvement in regulating antibiotic release. In this review, we first provide a brief introduction to prosthetic joint infections, and the background concepts of therapeutic efficacy and toxicity in antibiotics. We then review the current state of ALBCs and their release characteristics before focusing on the research and development in controlling the antibiotic release and osteo-conductivity/inductivity. We then conclude by a discussion on the need for better in vitro experiment designs such that the release results can be extrapolated to predict better the local antibiotic concentrations in vivo.

Synthetic Polymeric Materials for Bone Replacement

Some treatment options available to repair bone defects are the use of autogenous and allogeneic bone grafts. The drawback of the first one is the donor site’s limitation and the need for a second operation on the same patient. In the allograft method, the problems are associated with transmitted diseases and high susceptibility to rejection. As an alternative to biological grafts, polymers can be used in bone repair. Some polymers used in the orthopedic field are poly(methyl methacrylate), poly(ether-ether-ketone), and ultra-high molecular weight polyethylene (UHMWPE). UHMWPE has drawn much attention since it combines low friction coefficient and high wear and impact resistance. However, UHMWPE is a bioinert material, which means that it does not interact with the bone tissue. UHMWPE composites and nanocomposites with hydroxyapatite (HA) are widely studied in the literature to mitigate these issues. HA is the main component of the inorganic phase in the natural bone, and the addition of this bioactive filler to the polymeric matrix aims to mimic bone composition. This brief review discusses some polymers used in orthopedic applications, focusing on the UHMWPE/HA composites as a potential bone substitute.

Cellulose acetate-gelatin-coated boron-bioactive glass biocomposite scaffolds for bone tissue engineering

In this study, we aimed to prepare and characterize porous scaffolds composed of pure and boron oxide (B₂O₃)-doped bioactive glass (BG) that were infiltrated by cellulose acetate-gelatin (CA-GE) polymer solution for bone tissue engineering applications. Composite scaffolds were cross-linked with glutaraldehyde after polymer coating to protect the structural integrity of the polymeric-coated scaffolds. The impact of B₂O₃ incorporation into BG-polymer porous scaffolds on the cross-sectional morphology, porosity, mechanical properties, degradation and bioactivity of the scaffolds was investigated. Human dental pulp stem cells (hDPSCs) were enzymatically isolated and used for cell culture studies. According to scanning electron microscope analysis, the porous structure of the scaffolds was preserved after polymer coating. After polymer infiltration, the porosity of the scaffolds decreased from 64.2% to 59.35% for pure BG scaffolds and from 67.3% to 58.9% for B₂O₃-doped scaffolds. Meanwhile, their compressive strengths increased from 0.13 to 0.57 MPa and from 0.20 to 0.82 MPa, respectively. After polymer infiltration, 7% B₂O₃-incorporated BG scaffolds had higher weight loss and Ca-P layer deposition than pure BG scaffolds, after 14 d of incubation in simulated body fluid at 37 °C. Higher attachment and proliferation of hDPSCs were observed on 7% B₂O₃-BG-CA/GE scaffolds. In addition, the alkaline phosphatase activity of the cells was about 1.25-fold higher in this group than that observed on BG-CA/GE scaffolds after 14 d of incubation in osteogenic medium, while their intracellular calcium amounts were 1.7-fold higher than observed on BG-CA/GE after 7 d of incubation in osteogenic medium. Our results suggested that porous cellulose acetate-gelatin-coated boron-BG scaffolds hold promise for bone tissue engineering applications.

The stability of carbapenems before and after admixture to PMMA-cement used for replacement surgery caused by Gram-negative bacteria

Background

Prosthetic joint infection (PJI) is a serious complication of orthopedic implant surgery. Treatment often includes the use of an antibiotic-loaded Polymethyl methacrylate (PMMA) bone cement spacer. Several antibiotics are commonly used for the preparation of these spacers, but due to the increasing number of infections with resistant Gram-negative bacteria, there is a need for the use of carbapenem antibiotics such as meropenem and imipenem as drugs of last resort. Unfortunately, the reaction heat generated during the preparation of the bone cement can be a major problem for the stability of these antibiotics. In the present study, the stability of meropenem and imipenem was tested before and after the admixture to PMMA bone cements.

Methods

High-performance liquid chromatography with ion-pairing reversed-phase separation and spectrophotometric detection was used for analysis. Stability tests with meropenem and imipenem were performed with antibiotics in solution and solid form at different temperatures (37 °C, 45 °C, 60 °C, 90 °C) and times (30 min, 60 min, 120 min). To test the stability of both antibiotics in PMMA after exposure to the reaction heat during polymerization, three different bone cements were used to generate specimens that contained defined amounts of antibiotics. Reaction heat was measured. The form bodies were mechanically crushed and aliquots were dissolved in ethyl acetate. Samples were prepared for HPLC DAD analysis.

Results

Meropenem and imipenem showed the highest degradation levels after heat stressed in solution, with maximum levels of 75% and 95%, respectively. In solid form, degradation levels decreased dramatically for meropenem (5%) and imipenem (13%). Stability tests of both carbapenems in bone cement showed that they remained largely stable during PMMA polymerization, with retrieved amounts of about 70% in Palacos^® R and Copal^® G+V, and between 80 and 90% in Copal^® spacem.

Conclusions

In contrast to the results of meropenem and imipenem in solution, both antibiotics remain stable in solid form and mostly stable in the cement after PMMA polymerization. The low degradation levels of both antibiotics after exposure to temperatures > 100 °C allow the conclusion that they can potentially be used for an application in PMMA cements.

Setting behavior, apatite-forming ability, mechanical strength of polymethylmethacrylate bone cement through bioactivity modification of phosphate functional groups combined with Ca2+ ions

Bioactivity modification helps polymethylmethacrylate (PMMA) bone cement to reinforce its interfacial adhesion to bone tissues through the chemical bonding of apatite. Since Si-OH groups combined with Ca²⁺ ions have succeeded in inducing apatite formation, more combinations of functional groups and active ions are being explored. In this study, Bis[2-(methacryloyloxy)ethyl] phosphate (B2meP) containing phosphate (=PO₄H) groups and Ca(CH₃COO)₂ supplying Ca²⁺ ion were adopted to investigate the feasibility of equipping PMMA bone cement with apatite-forming ability in vitro, more effects under designed contents on setting behavior, injectability, contact angle, cytotoxicity and mechanical strength were also investigated. Results showed B2meP copolymerized with MMA and became one section of PMMA chains, surface = PO₄H groups and released Ca²⁺ ions pushed spherical apatite individuals nucleating and agglomerating into layer horizontally, Increasing B2meP content lowered the contact angle and the peak temperature, enhanced the cell viability of MC3T3-E1, but prolonged apatite forming period. Injectability rate performed a similar trend to setting time. Lower adding content and deposited apatite layer contributed to reduce the strength loss in soaking. Taking biological performance and other properties into balance, cement added with B2meP of 10 wt% in MMA and Ca(CH₃COO)₂ of 20 wt% in PMMA performed better.

Lipid-based nanosystems for targeting bone implant-associated infections: current approaches and future endeavors

Bone infections caused by Staphylococcus aureus are a major concern in medical care, particularly when associated with orthopedic-implant devices. The ability of the bacteria to form biofilms and their capacity to invade and persist within osteoblasts turn the infection eradication into a huge challenge. The reduction of antibiotic penetration through bacterial biofilms associated with the presence of persistent cells, ability to survive in the host, and high tolerance to antibiotics are some of the reasons for the difficult treatment of these infections. Effective therapeutic approaches are urgently needed. In this sense, lipid-based nanosystems, such as liposomes, have been investigated as an innovative and alternative strategy for the treatment of implant-associated S. aureus infections, due to their preferential accumulation at infected sites and interaction with S. aureus. This review highlights the recent advances on antibiotic-loaded liposome formulations both in vitro and in vivo and how the interaction with S. aureus biofilms may be improved by modulating the liposomal external surface. Graphical Abstract.

Synthetic Bone Substitutes and Mechanical Devices for the Augmentation of Osteoporotic Proximal Humeral Fractures: A Systematic Review of Clinical Studies

BACKGROUND

Different augmentation techniques have been described in the literature in addition to the surgical treatment of proximal humeral fractures. The aim of this systematic review was to analyze the use of cements, bone substitutes, and other devices for the augmentation of proximal humeral fractures.

METHODS

A systematic review was conducted by using PubMed/MEDLINE, ISI Web of Knowledge, Cochrane Library, Scopus/EMBASE, and Google Scholar databases according the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines over the years 1966 to 2019. The search term "humeral fracture proximal" was combined with "augmentation"; "polymethylmethacrylate, PMMA"; "cement"; "bone substitutes"; "hydroxyapatite"; "calcium phosphates"; "calcium sulfate"; "cell therapies", and "tissue engineering" to find the literature relevant to the topic under review.

RESULTS

A total of 10 clinical studies considered eligible for the review, with a total of 308 patients, were included. Mean age at the time of injury was 68.8 years (range of 58-92). The most commonly described techniques were reinforcing the screw-bone interface with bone PMMA cement (three studies), filling the metaphyseal void with synthetic bone substitutes (five studies), and enhancing structural support with metallic devices (two studies).

CONCLUSION

PMMA cementation could improve screw-tip fixation. Calcium phosphate and calcium sulfate injectable composites provided good biocompatibility, osteoconductivity, and lower mechanical failure rate when compared to non-augmented fractures. Mechanical devices currently have a limited role. However, the available evidence is provided mainly by level III to IV studies, and none of the proposed techniques have been sufficiently studied.

Self-healing biomaterials: The next generation is nano

The U.S. Agency for Healthcare Research and Quality estimates that there are over 1 million total hip and total knee replacements each year in the U.S. alone. Twenty five percent of those implants will experience aseptic loosening, and bone cement failure is an important part of this. Bone cements are based on poly(methyl methacrylate) (PMMA) systems that are strong but brittle polymers. PMMA-based materials are also essential to modern dental fillings, and likewise, the failure rates are high with lifetimes of 3-10 years. These brittle polymers are an obvious target for self-healing systems which could reduce revision surgeries and visits to dentist. Self-healing polymers have been described in the literature since 1996 and examples from Roman times are known, but their application in medicine has been challenging. This review looks at the development of self-healing biomaterials for these applications and the challenges that lie between development and the clinic. Many of the most promising formulations involve introducing nanoscale components which offer substantial potential benefits over their microscale counterparts especially in composite systems. There is substantial promise for translation, but issues with toxicity, robustness, and reproducibility of these materials in the complex environment of the body must be addressed. This article is categorized under: Therapeutic Approaches and Drug Discovery > Emerging Technologies Nanotechnology Approaches to Biology > Nanoscale Systems in Biology Implantable Materials and Surgical Technologies > Nanomaterials and Implants.

The Role of Poly(Methyl Methacrylate) in Management of Bone Loss and Infection in Revision Total Knee Arthroplasty: A Review

Poly(methyl methacrylate) (PMMA) is widely used in joint arthroplasty to secure an implant to the host bone. Complications including fracture, bone loss and infection might cause failure of total knee arthroplasty (TKA), resulting in the need for revision total knee arthroplasty (rTKA). The goals of this paper are: (1) to identify the most common complications, outside of sepsis, arising from the application of PMMA following rTKA, (2) to discuss the current applications and drawbacks of employing PMMA in managing bone loss, (3) to review the role of PMMA in addressing bone infection following complications in rTKA. Papers published between 1970 to 2018 have been considered through searching in Springer, Google Scholar, IEEE Xplore, Engineering village, PubMed and weblinks. This review considers the use of PMMA as both a bone void filler and as a spacer material in two-stage revision. To manage bone loss, PMMA is widely used to fill peripheral bone defects whose depth is less than 5 mm and covers less than 50% of the bone surface. Treatment of bone infections with PMMA is mainly for two-stage rTKA where antibiotic-loaded PMMA is inserted as a spacer. This review also shows that using antibiotic-loaded PMMA might cause complications such as toxicity to surrounding tissue, incomplete antibiotic agent release from the PMMA, roughness and bacterial colonization on the surface of PMMA. Although PMMA is the only commercial bone cement used in rTKA, there are concerns associated with using PMMA following rTKA. More research and clinical studies are needed to address these complications.

PMMA-Based Bone Cements and the Problem of Joint Arthroplasty Infections: Status and New Perspectives

Polymethyl methacrylate (PMMA)-based bone cement is a biomaterial that has been used over the last 50 years to stabilize hip and knee implants or as a bone filler. Although PMMA-based bone cement is widely used and allows a fast-primary fixation to the bone, it does not guarantee a mechanically and biologically stable interface with bone, and most of all it is prone to bacteria adhesion and infection development. In the 1970s, antibiotic-loaded bone cements were introduced to reduce the infection rate in arthroplasty; however, the efficiency of antibiotic-containing bone cement is still a debated issue. For these reasons, in recent years, the scientific community has investigated new approaches to impart antibacterial properties to PMMA bone cement. The aim of this review is to summarize the current status regarding antibiotic-loaded PMMA-based bone cements, fill the gap regarding the lack of data on antibacterial bone cement, and explore the progress of antibacterial bone cement formulations, focusing attention on the new perspectives. In particular, this review highlights the innovative study of composite bone cements containing inorganic antibacterial and bioactive phases, which are a fascinating alternative that can impart both osteointegration and antibacterial properties to PMMA-based bone cement.

Structural and Functional Dynamics of Staphylococcus aureus Biofilms and Biofilm Matrix Proteins on Different Clinical Materials

Medical device-associated staphylococcal infections are a common and challenging problem. However, detailed knowledge of staphylococcal biofilm dynamics on clinically relevant surfaces is still limited. In the present study, biofilm formation of the Staphylococcus aureus ATCC 25923 strain was studied on clinically relevant materials-borosilicate glass, plexiglass, hydroxyapatite, titanium and polystyrene-at 18, 42 and 66 h. Materials with the highest surface roughness and porosity (hydroxyapatite and plexiglass) did not promote biofilm formation as efficiently as some other selected materials. Matrix-associated poly-N-acetyl-β-(1-6)-glucosamine (PNAG) was considered important in young (18 h) biofilms, whereas proteins appeared to play a more important role at later stages of biofilm development. A total of 460 proteins were identified from biofilm matrices formed on the indicated materials and time points-from which, 66 proteins were proposed to form the core surfaceome. At 18 h, the appearance of several r-proteins and glycolytic adhesive moonlighters, possibly via an autolysin (AtlA)-mediated release, was demonstrated in all materials, whereas classical surface adhesins, resistance- and virulence-associated proteins displayed greater variation in their abundances depending on the used material. Hydroxyapatite-associated biofilms were more susceptible to antibiotics than biofilms formed on titanium, but no clear correlation between the tolerance and biofilm age was observed. Thus, other factors, possibly the adhesive moonlighters, could have contributed to the observed chemotolerant phenotype. In addition, a protein-dependent matrix network was observed to be already well-established at the 18 h time point. To the best of our knowledge, this is among the first studies shedding light into matrix-associated surfaceomes of S. aureus biofilms grown on different clinically relevant materials and at different time points.

Detoxification of poly(methyl methacrylate) bone cement by natural antioxidant intervention

Poly(methyl methacrylate) (PMMA) bone cement is the most widely used grouting material in the joint arthroplasties and vertebroplasties. The present investigation has been carried out to scavenge the radicals and monomer by addition of an antioxidant to minimize the toxicity of bone cement (BC). The in silico studies were employed to determine the potent natural antioxidant at physiological conditions. The antioxidant methionine demonstrated a strong binding affinity with free radicals and methyl methacrylate (MMA) monomer than cysteine. The designated amount of methionine was optimized by various assay methods and >2% methionine shows strong scavenging capacity in BC. Moreover, the antioxidant-loaded BC (ABC) demonstrated similar handling, physicochemical and mechanical properties to pristine bone cement. Significantly, the developed formulation shows superior biological characteristics such as cell proliferation (2 ± 1 BC and 6 ± 1 ABC), adhesion (0.32 ± 0.02 BC and 0.54 ± 0.01 ABC), and cell viability (81 ± 2% BC and 93 ± 1% ABC) toward human osteoblast-like cells (MG-63). Therefore, the novel antioxidant bone cement is a potential candidate for various orthopedic applications to eliminate the adverse effects, related to residual toxic radical and monomer in bone cement.

Bench-to-bedside strategies for osteoporotic fracture: From osteoimmunology to mechanosensation

Osteoporosis is characterized by a decrease in bone mass and strength, rendering people prone to osteoporotic fractures caused by low-energy forces. The primary treatment strategy for osteoporotic fractures is surgery; however, the compromised and comminuted bones in osteoporotic fracture sites are not conducive to optimum reduction and rigid fixation. In addition, these patients always exhibit accompanying aging-related disorders, including high inflammatory status, decreased mechanical loading and abnormal skeletal metabolism, which are disadvantages for fracture healing around sites that have undergone orthopedic procedures. Since the incidence of osteoporosis is expected to increase worldwide, orthopedic surgeons should pay more attention to comprehensive strategies for improving the poor prognosis of osteoporotic fractures. Herein, we highlight the molecular basis of osteoimmunology and bone mechanosensation in different healing phases of elderly osteoporotic fractures, guiding perioperative management to alleviate the unfavorable effects of insufficient mechanical loading, high inflammatory levels and pathogen infection. The well-informed pharmacologic and surgical intervention, including treatment with anti-inflammatory drugs and sufficient application of antibiotics, as well as bench-to-bedside strategies for bone augmentation and hardware selection, should be made according to a comprehensive understanding of bone biomechanical properties in addition to the remodeling status of osteoporotic bones, which is necessary for creating proper biological and mechanical environments for bone union and remodeling. Multidisciplinary collaboration will facilitate the improvement of overall osteoporotic care and reduction of secondary fracture incidence.

Comparative Study of Antibiotic Elution Profiles From Alternative Formulations of Polymethylmethacrylate Bone Cement

BACKGROUND

Polymethylmethacrylate (PMMA) bone cement is commonly used in orthopedic surgery for implant fixation and local antibiotic delivery following surgical debridement. The incidence of nephrotoxicity necessitates the balance of antiinfective properties with the potential for toxicity. Thus, understanding antibiotic elution characteristics of different PMMA formulations is essential. We sought to address this by assessing elution of vancomycin, daptomycin, and tobramycin from Palacos LV (Palacos), Stryker Surgical Simplex P (Simplex), BIOMET Cobalt HV (Cobalt), and Zimmer Biomet Bone Cement R (Zimmer) radiopaque bone cements.

METHODS

Antibiotics were mixed with each cement formulation, and molds were used to produce beads of cement. Beads were incubated in phosphate-buffered saline at 37°C, and antibiotic elution was measured daily for 10 days with vancomycin and 5 days with daptomycin and tobramycin. Active antibiotic was quantified by serial dilution and comparison to the minimum inhibitory concentration.

RESULTS

The elution profiles of Simplex were significantly lower than all other cements with all antibiotics (P < .00093). Palacos exhibited a significantly higher vancomycin elution profile than all other cements (P < .00001). The difference in daptomycin elution profiles for Cobalt and Palacos was not significant (P > .43), but both were significantly higher than Zimmer (P < .0006).

CONCLUSION

Overall, Stryker Surgical Simplex P exhibits a significantly lower elution profile than all other cements tested. In general, Palacos LV exhibits an increased elution profile compared with other cements. This elution information may assist the surgeon in choosing different cement formulations for the local delivery of antibiotics.

Equivalent hip stem fixation by Hi-Fatigue G and Palacos R + G bone cement: a randomized radiostereometric controlled trial of 52 patients with 2 years' follow-up

Background and purpose - Long-term fixation of cemented femoral stems relies on several factors including cement adhesion and fatigue. Hi-Fatigue is a newer third-generation bone cement with low-viscosity properties at room temperature, good mechanical strength, and stable bone-cement interface in a laboratory testing environment. Palacos bone cement has excellent 10-year survival and is considered gold standard. We compared stem subsidence after fixation with Hi-Fatigue and Palacos bone cements using radiostereometry. Patients and methods - In a patient-blinded randomized controlled trial, 52 patients (30 women) at mean age 76 years (71-87) with osteoarthrosis and no osteoporosis received Hi-Fatigue G or Palacos R + G cement fixation of collarless, polished, double-tapered stems (CPT). Tantalum beads were inserted in the periprosthetic bone. Supine stereoradiographs were obtained postoperatively, 3 months, 6 months, 1 year, and 2 years after surgery. Oxford Hip Score (OHS) and VAS pain were recorded preoperatively and 1 and 2 years after surgery. Cement working times and properties were registered. Results - At 2 years, mean stem subsidence of 1.12 mm (95% CI 0.96-1.29) for Hi-Fatigue and 1.19 mm (CI 1.03-1.34) for Palacos was similar. Likewise, stem version was comparable between cement groups. Mean OHS and VAS pain were similar between cement groups. Cement working times were similar between cement groups, but the mean curing time was longer for Hi-Fatigue (13.7 min) than for Palacos (11.6 min). Interpretation - We found similar and generally low migration of CPT femoral stems inserted with Hi-Fatigue and Palacos bone cement until 2 years' follow-up, which indicates a good long-term survival of polished taper femoral stems inserted with both cement types.

In Situ Generated Medical Devices

Medical devices play a major role in all areas of modern medicine, largely contributing to the success of clinical procedures and to the health of patients worldwide. They span from simple commodity products such as gauzes and catheters, to highly advanced implants, e.g., heart valves and vascular grafts. In situ generated devices are an important family of devices that are formed at their site of clinical function that have distinct advantages. Among them, since they are formed within the body, they only require minimally invasive procedures, avoiding the pain and risks associated with open surgery. These devices also display enhanced conformability to local tissues and can reach sites that otherwise are inaccessible. This review aims at shedding light on the unique features of in situ generated devices and to underscore leading trends in the field, as they are reflected by key developments recently in the field over the last several years. Since the uniqueness of these devices stems from their in situ generation, the way they are formed is crucial. It is because of this fact that in this review, the medical devices are classified depending on whether their in situ generation entails chemical or physical phenomena.

Loading necrostatin-1 composite bone cement inhibits necroptosis of bone tissue in rabbit

Bone necrosis after injecting of polymethylmethacrylate (PMMA) bone cement will lead to re-fracture of bone tissue. As a new type of necrosis, there is little research related to the necroptosis of surrounding bone tissue near the bone cement. The purpose of our study was to (i) investigate the presence of necroptosis in vivo and, (ii) established as a new type of bone cement containing PMMA, calcium phosphate cement (CPC) and Necrostatin-1 (Nec-1) to inhibit necroptosis of bone tissue. A total of 12 Japanese rabbits were used to establish the animal model and randomly divided into 4 groups signed as a control group, PMMA group, PMMA-CPC group and PMMA-CPC-Nec-1 group, respectively. We used scanning electron microscope to observe the structure of the samples, used HE staining to detect the necrosis, and used western blotting as well as ELISA test to examine the iconic molecule receptor interacting protein kinase-3 (RIP 3) protein and tumor necrosis factor α (TNF-α). After analyzing the results of our study, we found that the structure in both PMMA bone cement group and composite bone cement group was damaged and there was an evidence of necrosis, but it was absent in control group. Through molecule detection, the RIP 3 protein expression was decreased in PMMA-CPC-Nec-1 (P < 0.05). TNF-α expression was increased in bone cement groups with and without CPC (P < 0.05), but was inhibited in PMMA-CPC-Nec-1 group. We have concluded that the necroptosis could be confirmed in bone tissue necrosis induced by TNF-α after bone cement injection and also could be inhibited by composite bone cement with Nec-1.

Fabrication of biocomposite scaffolds made with modified hydroxyapatite inclusion of chitosan-grafted-poly(methyl methacrylate) for bone tissue engineering

In the present study, composite scaffolds of chitosan-graft-poly(methyl methacrylate) (Chi-g-PMMA) and mineral ions-loaded hydroxyapatite (mHA) (obtained by the hydrothermal treatment of hydroxyapatite (HA) in a simulated body fluid (SBF) solution (mHA@Chi-g-PMMA)) were prepared by the blending method. The physical properties, bioactivity, biological properties and their capabilities for sustained drug and protein release were studied. Physicochemical analysis showed a successful incorporation of the mineral ions in the HA particles and a good distribution of the mHA within the Chi-g-PMMA polymer matrix. The compressive strength and the Young's modulus were 15.760 ± 0.718 and 658.452 ± 17.020 MPa, respectively. In bioactivity studies, more apatite formation on the surface were seen after immersion in the SBF solution. In vitro growth experiments using UMR-106 osteoblast-like cells on the mHA@Chi-g-PMMA scaffold case showed that the attachment, viability and proliferation of the cells on the scaffolds had improved after 7 d of immersion. The in vitro release of two compounds (the cancer drug, doxorubicin (DOX)) and bovine serum albumin (BSA)), which had been attached to separate mHA@Chi-g-PMMA scaffolds, were studied to determine their suitability as drug delivery vehicles. It was found that the sustained release of DOX was 73.95% and of BSA was 57.27% after 25 h of incubation. These experimental results demonstrated that the mHA@Chi-g-PMMA composite can be utilized as a scaffold for bone cells ingrowth and also be used for drug delivery during the bone repairing.

Rifampin and tobramycin combination with PMMA antibiotic cement

Rifampin is a powerful antibiotic used in the treatment of biofilm-forming bacteria with studies supporting its use in PMMA cement. However, it has not been widely accepted for its use in PMMA cement due to a perception that it is unable to solidify in a timely manner. The technique described consists of ratio of aminoglycoside and rifampin that reduces time to solidification to approximately 15-20 min.

Copper-Doped Bioactive Glass as Filler for PMMA-Based Bone Cements: Morphological, Mechanical, Reactivity, and Preliminary Antibacterial Characterization

To promote osteointegration and simultaneously limit bacterial contamination without using antibiotics, we designed innovative composite cements containing copper (Cu)-doped bioactive glass powders. Cu-doped glass powders were produced by a melt and quenching process, followed by an ion-exchange process in a Cu salt aqueous solution. Cu-doped glass was incorporated into commercial polymethyl methacrylate (PMMA)-based cements with different viscosities. The realized composites were characterized in terms of morphology, composition, leaching ability, bioactivity, mechanical, and antibacterial properties. Glass powders appeared well distributed and exposed on the PMMA surface. Composite cements showed good bioactivity, evidencing hydroxyapatite precipitation on the sample surfaces after seven days of immersion in simulated body fluid. The leaching test demonstrated that composite cements released a significant amount of copper, with a noticeable antibacterial effect toward Staphylococcus epidermidis strain. Thus, the proposed materials represent an innovative and multifunctional tool for orthopedic prostheses fixation, temporary prostheses, and spinal surgery.

Healing potentials of polymethylmethacrylate bone cement combined with platelet gel in the critical-sized radial bone defect of rats

Polymethylmethacrylate (PMMA) is the most commonly used filler material that lacks biological properties and osteoconductivity or osteoinductivity. Platelet gel (PG) is a typical source of growth factors, cytokines and molecules efficient for bone formation and remodeling. The aim of this study was to evaluate bone healing and regeneration of bone defect in rat model by combining PMMA with PG. A total of 50 defects were created in the diaphysis of the radii of 25 male Sprague-Dawley rats. These defects were randomly divided into five groups (n = 10 defects for each group) and treated by autograft, plain PMMA, PG and PMMA-PG or left untreated. The rats were examined clinically and radiologically during the experiment and also after euthanasia at the 8^th post-operative week, the healed defects were evaluated by gross morphology, histopathology, histomorphometry, computed tomography, scanning electron microscopy and biomechanical testing. PG could function as efficiently as autograft in promoting bone healing of the radial bones. Additionally, bone formation, and densities of cartilaginous and osseous tissues in the defects treated with autograft, PG and PMMA-PG were more satisfactory than the untreated and PMMA treated defects. Compared with the PMMA-PG implant, more PMMA residuals remained in the defect area and induced more intense inflammatory reaction. In conclusion, addition of PG could improve the bone regenerative properties of PMMA bone cement compared with PMMA alone in vivo. Therefore, the PG-PMMA can be proposed as a promising option to increase regenerative potential of PMMA, particularly when it is used as fixator, filler or adhesive in the dentistry, neurosurgery and bone tissue engineering applications.

Biological Activity of an Injectable Biphasic Calcium Phosphate/PMMA Bone Cement for Induced Osteogensis in Rabbit Model

Polymethylmethacrylate (PMMA) bone cement is widely used in repair of vertebral fracture because of its good biomechanical properties and fast curing. However, the bioinertness of PMMA cement may cause interfacial loosening, fatigue, fracture, and ultimate failure. In this study, biphasic calcium phosphate (BCP) is introduced into PMMA cement to prepare an injectable composite bone cement (BCP_x /PMMA) and the content of BCP is optimized to achieve appropriate rate of absorption that matches the bone regeneration. The compressive strength of BCP_x /PMMA bone cement is found to comply with the International Standardization Organization standard 5833, and can promote biomineralization as well as adhesion, proliferation, and osteogenic differentiation of Sprague-Dawley rat bone marrow mesenchymal stem cells in vitro. Furthermore, in vivo test performed on a rabbit radius defect model demonstrates that the presence of BCP can significantly improve the osteogenic efficacy of PMMA cement. Therefore, it is anticipated that BCP_x /PMMA bone cement, as a promising injectable biomaterial, is of great potential in bone tissue regeneration.

Role of fast-setting cements in arthroplasty: A comparative analysis of characteristics

AIM

To evaluate the behaviour of two fast-setting polymethylmethacrylate (PMMA) cements CMW^® 2G and Palacos^® fast R + G, as reference: Standard-setting Palacos^® R + G.

METHODS

The fast-setting cements CMW^® 2G and Palacos^® fast R + G were studied, using standard-setting high viscosity Palacos^® R + G as a reference. Eleven units (of two batch numbers) of each cement were tested. All cements were mixed as specified by the manufacturer and analysed on the following parameters: Handling properties (mixing, waiting, working and hardening phase) according to Kuehn, Mechanical properties according to ISO 5833 and DIN 53435, Fatigue strength according to ISO 16402, Benzoyl Peroxide (BPO) - Content by titration, powder/liquid-ratio by weighing, antibiotic elution profile by High Performance Liquid Chromatography. All tests were done in an acclimatised laboratory with temperatures set at 23.5 °C ± 0.5 °C and a humidity of > 40%.

RESULTS

Palacos^® fast R + G showed slightly shorter handling properties (doughing, hardening phase, n = 12) than CMW^® 2G, allowing to reduce operative time and to optimise cemented cup implantation. Data of the quasistatic properties of ISO 5833 and DIN 53435 of both cements tested was comparable. The ISO compressive strength (MPa) of Palacos^® fast R + G was significantly higher than CMW^® 2G, resulting in ANOVA (P < 0.01) and two sample t-test (P < 0.01) at 0.05 level of significance (n = 20). Palacos^® fast R + G showed a higher fatigue strength of about 18% mean (ISO 16402) of 15.3 MPa instead of 13.0 MPa for CMW^® 2G (n = 5 × 10⁶ cycles). Palacos^® fast R + G and CMW^® 2G differed only by 0.11% (n = 6) with the former having the higher content. The BPO-content of both cements were therefore comparable. CMW^® 2G had a powder/liquid ratio of 2:1, Palacos^® fast R + G of 2.550:1 due to a higher powder content. Despite its higher gentamicin content, CMW^® 2G showed a significantly lower antibiotic elution over time than Palacos^® fast R + G (n = 3).

CONCLUSION

Both cements are compliant with international standards and are highly suitable for their specified surgical indications, affording a time-saving measure without detriment to the mechanical properties.

Yolk shell nanocomposite particles as bioactive bone fillers and growth factor carriers

The efficient delivery of bioactive molecules via rationally designed nanoparticles is an important focus in regenerative medicine. The yolk shell nanocomposite particles described herein are composed of silk fibroin movable cores formed within voided calcium carbonate shells to load and control the release of labile cytokines. These particles are excellent carrier vehicles of potent molecules as they sustained the release of bioactive Bone Morphogenetic Protein 2 (BMP-2) for more than 28 days in vitro. Implantation into bone defects in rabbits corroborates the in vitro results and also reveals that upon contact with phosphate containing body fluids, implanted yolk shell particles agglomerate and transform into a filler that adapts to defect contour to further act as an absorbable hemostatic agent. Taken together, the fabrication of these yolk shell particle-based "bone fillers" could expand the horizon for the development of newer generations of advanced bioactive materials in tissue regeneration applications.