Ambient sampling/ionization mass spectrometry: applications and current trends

Sensitive ionization of non-volatile analytes using protein solutions as spray liquid in desorption electrospray ionization mass spectrometry

RATIONALE

Desorption electrospray ionization (DESI) is the most popular ambient ionization technique for direct analysis of complex samples without sample pretreatment. However, for many applications, especially for trace analysis, it is of interest to improve the sensitivity of DESI-mass spectrometry (MS).

METHODS

In traditional DESI-MS, a mixture of methanol/water/acetic acid is usually used to generate the primary ions. In this article, dilute protein solutions were electrosprayed in the DESI method to create multiply charged primary ions for the desorption ionization of trace analytes on various surfaces (e.g., filter paper, glass, Al-foil) without any sample pretreatment. The analyte ions were then detected and structurally characterized using a LTQ XL mass spectrometer.

RESULTS

Compared with the methanol/water/acetic acid (49:49:2, v/v/v) solution, protein solutions significantly increased the signal levels of non-volatile compounds such as benzoic acid, TNT, o-toluidine, peptide and insulin in either positive or negative ion detection mode. For all the analytes tested, the limits of detection (LODs) were reduced to about half of the original values which were obtained using traditional DESI. The results showed that the signal enhancement is highly correlated with the molecular weight of the proteins and the selected solid surfaces.

CONCLUSIONS

The proposed DESI method is a universal strategy for rapid and sensitive detection of trace amounts of strongly bound and/or non-volatile analytes, including explosives, peptides, and proteins. The results indicate that the sensitivity of DESI can be further improved by selecting larger proteins and appropriate solid surfaces.

Scanning probe electrospray ionization for ambient mass spectrometry

RATIONALE

Ambient sampling and ionization techniques have been attracting attention in imaging mass spectrometry because they offer the advantage of rapid testing. We have developed a method which exploits the fluid motion of charged solvents for both local sampling and ionization with a single vibrating capillary probe.

METHODS

The capillary probe was used to supply solvents in order to form a liquid bridge between the probe and a sample surface. A bias voltage was applied to the solvents to generate electrospray ionization (ESI). The probe was also vibrated by either an ultrasonic transducer fixed at the back of the sample (contact-mode) or spontaneous vibration of probe itself (tapping-mode). The ions generated by ESI were detected by a triple quadrupole mass spectrometer.

RESULTS

Sampling of the specimens at the liquid bridge and ESI of the dissolved solutions both occurred around the probe apex. The sampling and ionization co-existed in contact-mode, while they were explicitly separated in the tapping-mode. The one-dimensional mapping of solid samples such as protein films and tissue sections was demonstrated. The results indicated that there was little cross-contamination during the operation.

CONCLUSIONS

The method, named scanning probe electrospray ionization (SPESI), promises to be a simple and unique approach toward direct sampling and ionization methodology.

Semitransparent nanostructured films for imaging mass spectrometry and optical microscopy

Semitransparent porous silicon substrates have been developed for pairing nanostructure-initiator mass spectrometry (NIMS) imaging with traditional optical-based microscopy techniques. Substrates were optimized to generate the largest NIMS signal while maintaining sufficient transparency to allow visible light to pass through for optical microscopy. Using these substrates, both phase-contrast and NIMS images of phospholipids from a scratch-wounded cell monolayer were obtained. NIMS images were generated using a spatial resolution of 14 μm. Coupled with further improvements in spatial resolution, this approach may allow for the localization of intact biological molecules within cells without the need for labeling.

Brazil nut oil: quality control via triacylglycerol profiles provided by easy ambient sonic-spray ionization mass spectrometry

Brazil nut oil is one of the important Amazonian natural products in the global market. Despite its health benefits and applications in food and cosmetic industries, authentication and quality control of the oil are far from satisfactory. Several samples of Amazonian Brazil nut oil (authentic oils of different geographic origins, commercial oils, and oils adulterated with soybean oil) were evaluated by easy ambient sonic-spray ionization mass spectrometry (EASI-MS). The samples were characterized on the basis of triacylglycerol profiles, and their major ions were subjected to chemometric treatment (principal component analysis). The ambient mass spectrometry analysis and the set of major ions allowed the characterization of authentic oils, commercial oils, and adulterated oils (5% soybean oil) in a few minutes and without sample preparation. Therefore, it is shown that quality control of Amazonian vegetable oils can be readily accomplished by EASI-MS.

Drop-on-demand sample introduction system coupled with the flowing atmospheric-pressure afterglow for direct molecular analysis of complex liquid microvolume samples

One of the fastest developing fields in analytical spectrochemistry in recent years is ambient desorption/ionization mass spectrometry (ADI-MS). This burgeoning interest has been due to the demonstrated advantages of the method: simple mass spectra, little or no sample preparation, and applicability to samples in the solid, liquid, or gaseous state. One such ADI-MS source, the flowing atmospheric-pressure afterglow (FAPA), is capable of direct analysis of solids just by aiming the source at the solid surface and sampling the produced ions into a mass spectrometer. However, direct introduction of significant volumes of liquid samples into this source has not been possible, as solvent loads can quench the afterglow and, thus, the formation of reagent ions. As a result, the analysis of liquid samples is preferably carried out by analyzing dried residues or by desorbing small amounts of liquid samples directly from the liquid surface. In the former case, reproducibility of sample introduction is crucial if quantitative results are desired. In the present study, introduction of liquid samples as very small droplets helps overcome the issues of sample positioning and reduced levels of solvent intake. A recently developed "drop-on-demand" (DOD) aerosol generator is capable of reproducibly producing very small volumes of liquid (∼17 pL). In this paper, the coupling of FAPA-MS and DOD is reported and applications are suggested. Analytes representing different classes of substances were tested and limits of detections were determined. Matrix tolerance was investigated for drugs of abuse and their metabolites by analyzing raw urine samples and quantification without the use of internal standards. Limits of detection below 2 μg/mL, without sample pretreatment, were obtained.

Analysis of chloroquine and metabolites directly from whole-body animal tissue sections by liquid extraction surface analysis (LESA) and tandem mass spectrometry

The rapid and direct analysis of the amount and spatial distribution of exogenous chloroquine (CHQ) and CHQ metabolites from tissue sections by liquid extraction surface sampling analysis coupled with tandem mass spectrometry (LESA-MS/MS) was demonstrated. LESA-MS/MS results compared well with previously published CHQ quantification data collected by organ excision, extraction and fluorescent detection. The ability to directly sample and analyze spatially resolved exogenous molecules from tissue sections with minimal sample preparation and analytical method development has the potential to facilitate the assessment of target tissue penetration of pharmaceutical compounds, to establish pharmacokinetic/pharmacodynamic relationships, and to complement established pharmacokinetic methods used in the drug discovery process during tissue distribution assessment.

Study of the efficiency for ion transfer through bent capillaries

Discontinuous atmospheric pressure interfaces (DAPIs) with bent capillaries represent a highly simplified and flexible means for introducing ions into a vacuum manifold for mass analysis or gas phase ion reactions. In this work, a series of capillaries of different radians and curvatures were used with DAPI for studying the impact of the capillary bending on the ion transfer. The variation of transfer efficiency was systematically characterized for dry and solvated ions. The efficiency loss for dry ions was less than one order of magnitude, even with a three-turn bent capillary. The transfer of solvated ions generated by electrospray was found to be minimally impacted by the bending of the transfer capillary. For multiply protonated ions, the transfer efficiency for ions at lower charge states could be relatively well retained, presumably due to the lower reactivity associated with proton transfer reaction and the compensation in intensity by conversion of ions at higher charge states.

Rapid identification of molecular changes in tulsi (Ocimum sanctum Linn) upon ageing using leaf spray ionization mass spectrometry

Tulsi or Holy Basil (Ocimum sanctum Linn) is a medicinally important plant. Ursolic acid (UA) and oleanolic acid (OA) are among its major constituents which account for many medicinal activities of the plant. In the present work, we deployed a new ambient ionization method, leaf spray ionization, for rapid detection of UA, OA and their oxidation products from tulsi leaves. Tandem electrospray ionization mass spectrometry (ESI-MS) has been performed on tulsi leaf extracts in methanol to establish the identity of the compounds. We probed changes occurring in the relative amounts of the parent compounds (UA and OA) with their oxidized products and the latter show an increasing trend upon ageing. The findings are verified by ESI-MS analysis of tulsi leaf extracts, which shows the same trend proving the reliability of the leaf spray method.

Infrared laser ablation sample transfer for on-line liquid chromatography electrospray ionization mass spectrometry

We have demonstrated an on-line laser ablation sampling system and coupling of the system to liquid chromatography (LC) using an infrared (IR) laser to ablate and transfer materials into a flowing solvent stream. With this approach, samples are deposited on a microscope slide mounted on a translation stage and ablated in transmission geometry using a pulsed mid-IR laser. The ablated material is captured in an exposed flowing solvent stream that carries the ablated material to the electrospray source. Post-ablation separation is accomplished using a capillary column downstream of the capture zone. The performance of the system was assessed using peptide and protein mixtures ablated from the target and analyzed with and without LC separation.

The expanding role of electrospray ionization mass spectrometry for probing reactive intermediates in solution

Within the past decade, electrospray ionization mass spectrometry (ESI-MS) has rapidly occupied a prominent position for liquid-phase mechanistic studies due to its intrinsic advantages allowing for efficient "fishing" (rapid, sensitive, specific and simultaneous detection/identification) of multiple intermediates and products directly from a "real-world" solution. In this review we attempt to offer a comprehensive overview of the ESI-MS-based methodologies and strategies developed up to date to study reactive species in reaction solutions. A full description of general issues involved with probing reacting species from complex (bio)chemical reaction systems is briefly covered, including the potential sources of reactive intermediate (metabolite) generation, analytical aspects and challenges, basic rudiments of ESI-MS and the state-of-the-art technology. The main purpose of the present review is to highlight the utility of ESI-MS and its expanding role in probing reactive intermediates from various reactions in solution, with special focus on current progress in ESI-MS-based approaches for improving throughput, testing reality and real-time detection by using newly developed MS instruments and emerging ionization sources (such as ambient ESI techniques). In addition, the limitations of modern ESI-MS in detecting intermediates in organic reactions is also discussed.

Recent advances in bioanalytical sample preparation for LC-MS analysis

Sample preparation has historically been, and continues to be, the most challenging part of the bioanalytical workflow. Several techniques have been developed over the years to deal with the problems of recovery and matrix effects in an effort to increase the reliability and robustness of the bioanalytical method. In recent years certain techniques have come into prominence and gained acceptance in routine sample preparation, and some have shown promise in their use in a discovery environment where speed is critical and method development time is often limited. The aim of this review is to examine several of these techniques and provide examples of their use from the literature, as well as comment on their utility in current workflows.

Direct and quantitative analysis of underivatized acylcarnitines in serum and whole blood using paper spray mass spectrometry

A simple protocol for rapid quantitation of acylcarnitines in serum and whole blood has been developed using paper spray mass spectrometry. Dried serum and whole blood containing a mixture of ten acylcarnitines at various concentrations were analyzed as spots from paper directly without any sample pretreatment, separation, or derivatization. The composition of the spray solvent was found to be a critical factor: for serum samples, spray solvent of methanol/water/formic acid (80:20:0.1) gave the best signal intensity while for blood samples which contain more matrix components, acetonitrile/water (90:10) was a much more suitable spray solvent. For the paper type and size used, 0.5 μL of sample provided an optimal signal for both serum and whole blood samples. For quantitative profiling, the limits of quantitation obtained from both serum and blood were much lower than the clinically validated cutoff values for diagnosis of fatty acid oxidation disorders in newborn screening. Linearity (R(2) > 0.95) and reproducibility (RSD ~10 %) were achieved in the concentration ranges from 100 nM to 5 μM for the C2 acylcarnitine, and for other acylcarnitines, these values were from 10 to 500 nM. Acylcarnitine profiles offer an effective demonstration of the fact that paper spray mass spectrometry is an appropriate, simple, rapid method with high sensitivity and high reproducibility applicable to newborn screening tests.

"Flow valve" microfluidic devices for simple, detectorless, and label-free analyte quantitation

Simplified analysis systems that offer the performance of benchtop instruments but the convenience of portability are highly desirable. We have developed novel, miniature devices that feature visual inspection readout of a target's concentration from a ~1 μL volume of solution introduced into a microfluidic channel. Microchannels are constructed within an elastomeric material, and channel surfaces are coated with receptors to the target. When a solution is flowed into the channel, the target cross-links multiple receptors on the surface, resulting in constriction of the first few millimeters of the channel and stopping of flow. Quantitation is performed by measuring the distance traveled by the target solution in the channel before flow stops. A key advantage of our approach is that quantitation is accomplished by simple visual inspection of the channel, without the need for complex detection instrumentation. We have tested these devices using the model system of biotin as a receptor and streptavidin as the target. We have also characterized three factors that influence flow distance: solution viscosity, device thickness, and channel height. We found that solution capillary flow distance scales with the negative logarithm of target concentration and have detected streptavidin concentrations as low as 1 ng/mL. Finally, we have identified and evaluated a plausible mechanism wherein time-dependent channel constriction in the first few millimeters leads to concentration-dependent flow distances. Their simplicity coupled with performance makes these "flow valve" systems especially attractive for a host of analysis applications.

Surface acoustic wave nebulization facilitating lipid mass spectrometric analysis

Surface acoustic wave nebulization (SAWN) is a novel method to transfer nonvolatile analytes directly from the aqueous phase to the gas phase for mass spectrometric analysis. The lower ion energetics of SAWN and its planar nature make it appealing for analytically challenging lipid samples. This challenge is a result of their amphipathic nature, labile nature, and tendency to form aggregates, which readily precipitate clogging capillaries used for electrospray ionization (ESI). Here, we report the use of SAWN to characterize the complex glycolipid, lipid A, which serves as the membrane anchor component of lipopolysaccharide (LPS) and has a pronounced tendency to clog nano-ESI capillaries. We also show that unlike ESI SAWN is capable of ionizing labile phospholipids without fragmentation. Lastly, we compare the ease of use of SAWN to the more conventional infusion-based ESI methods and demonstrate the ability to generate higher order tandem mass spectral data of lipid A for automated structure assignment using our previously reported hierarchical tandem mass spectrometry (HiTMS) algorithm. The ease of generating SAWN-MS(n) data combined with HiTMS interpretation offers the potential for high throughput lipid A structure analysis.

Quantification and remote detection of nitro explosives by helium plasma ionization mass spectrometry (HePI-MS) on a modified atmospheric pressure source designed for electrospray ionization

Helium Plasma Ionization (HePI) generates gaseous negative ions upon exposure of vapors emanating from organic nitro compounds. A simple adaptation converts any electrospray ionization source to a HePI source by passing helium through the sample delivery metal capillary held at a negative potential. Compared with the demands of other He-requiring ambient pressure ionization sources, the consumption of helium by the HePI source is minimal (20-30 ml/min). Quantification experiments conducted by exposing solid deposits to a HePI source revealed that 1 ng of 2,4,6-trinitrotoluene (TNT) on a filter paper (about 0.01 ng/mm(2)) could be detected by this method. When vapor emanating from a 1,3,5-trinitroperhydro-1,3,5-triazine (RDX) sample was subjected to helium plasma ionization mass spectrometry (HePI-MS), a peak was observed at m/z 268 for (RDX●NO(2))(-). This facile formation of NO(2)(-) adducts was noted without the need of any extra additives as dopants. Quantitative evaluations showed RDX detection by HePI-MS to be linear over at least three orders of magnitude. TNT samples placed even 5 m away from the source were detected when the sample headspace vapor was swept by a stream of argon or nitrogen and delivered to the helium plasma ion source via a metal tube. Among the tubing materials investigated, stainless steel showed the best performance for sample delivery. A system with a copper tube, and air as the carrier gas, for example, failed to deliver any detectable amount of TNT to the source. In fact, passing over hot copper appears to be a practical way of removing TNT or other nitroaromatics from ambient air.

Building blocks for the development of an interface for high-throughput thin layer chromatography/ambient mass spectrometric analysis: a green methodology

Interfacing thin layer chromatography (TLC) with ambient mass spectrometry (AMS) has been an important area of analytical chemistry because of its capability to rapidly separate and characterize the chemical compounds. In this study, we have developed a high-throughput TLC-AMS system using building blocks to deal, deliver, and collect the TLC plate through an electrospray-assisted laser desorption ionization (ELDI) source. This is the first demonstration of the use of building blocks to construct and test the TLC-MS interfacing system. With the advantages of being readily available, cheap, reusable, and extremely easy to modify without consuming any material or reagent, the use of building blocks to develop the TLC-AMS interface is undoubtedly a green methodology. The TLC plate delivery system consists of a storage box, plate dealing component, conveyer, light sensor, and plate collecting box. During a TLC-AMS analysis, the TLC plate was sent to the conveyer from a stack of TLC plates placed in the storage box. As the TLC plate passed through the ELDI source, the chemical compounds separated on the plate would be desorbed by laser desorption and subsequently postionized by electrospray ionization. The samples, including a mixture of synthetic dyes and extracts of pharmaceutical drugs, were analyzed to demonstrate the capability of this TLC-ELDI/MS system for high-throughput analysis.

Improved spatial resolution in the imaging of biological tissue using desorption electrospray ionization

Desorption electrospray ionization imaging allows biomarker discovery and disease diagnosis through chemical characterization of biological samples in their native environment. Optimization of experimental parameters including emitter capillary size, solvent composition, solvent flow rate, mass spectrometry scan-rate and step-size is shown here to improve the resolution available in the study of biological tissue from 180 μm to about 35 μm using an unmodified commercial mass spectrometer. Mouse brain tissue was used to optimize and measure resolution based on known morphological features and their known relationships to major phospholipid components. Features of approximately 35 μm were resolved and correlations drawn between features in grey matter (principally PS (18:0/22:6), m/z 834) and in white matter (principally ST (24:1), m/z 888). The improved spatial resolution allowed characterization of the temporal changes in lipid profiles occurring within mouse ovaries during the ovulatory cycle. An increase in the production of phosphatidylinositol (PI 38:4) m/z 885 and associated fatty acids such as arachidonic acid (FA 20:4) m/z 303 and adrenic acid (FA 22:4) m/z 331was seen with the postovulatory formation of the corpus luteum.

Surface analysis using a new plasma assisted desorption/ionisation source for mass spectrometry in ambient air

The authors report on a modified micro-plasma assisted desorption/ionisation (PADI) device which creates plasma through the breakdown of ambient air rather than utilising an independent noble gas flow. This new micro-PADI device is used as an ion source for ambient mass spectrometry to analyse species released from the surfaces of polytetrafluoroethylene, and generic ibuprofen and paracetamol tablets through remote activation of the surface by the plasma. The mass spectra from these surfaces compare favourably to those produced by a PADI device constructed using an earlier design and confirm that the new ion source is an effective device which can be used to achieve ambient mass spectrometry with improved spatial resolution.

Surface acoustic wave nebulization produces ions with lower internal energy than electrospray ionization

Surface acoustic wave nebulization (SAWN) has recently been reported as a novel method to transfer non-volatile analytes directly from solution to the gas phase for mass spectrometric analysis. Here we present a comparison of the survival yield of SAWN versus electrospray ionization (ESI) produced ions. A series of substituted benzylpyridinium (BzPy) compounds were utilized to measure ion survival yield from which ion energetics were inferred. We also estimated bond dissociation energies using higher level quantum chemical calculations than previously reported for BzPy ions. Additionally, the effects on BzPy precursor ion survival of SAWN operational parameters such as inlet capillary temperature and solution flow-rate were investigated. Under all conditions tested, SAWN-generated BzPy ions displayed a higher tendency for survival and thus have lower internal energies than those formed by ESI.

Semi-automated direct elution of dried blood spots for the quantitative determination of guanfacine in human blood

Background: Direct analysis of dried blood spot (DBS) samples was investigated using a prototype semi-automated robotic device that allows the direct elution of sample spots from a DBS paper card to an online SPE cartridge. The eluted SPE samples were analyzed with high-performance LC–MS/MS. Results: A LLOQ of 0.01 ng/ml was achieved with a linear calibration range from 0.01 to 25 ng/ml. Optimal performance data were obtained from spotting the internal standard solution on the card before blood spotting. Internal standard addition from the system injector loop produced intra-assay inaccuracy of -9.0–7.3% and precision of 1.3–8.2%, and inter-assay inaccuracy of -3.5–3.9% and precision of 4.4–8.7%. Conclusion: Results demonstrated the feasibility of a semi-automated online rapid direct elution method that avoids manual extraction for DBS sample analysis using the online DBS-SPE system coupled to LC–MS/MS.

Analysis of select Dalbergia and trade timber using direct analysis in real time and time-of-flight mass spectrometry for CITES enforcement

RATIONALE

International trade of several Dalbergia wood species is regulated by The Convention on International Trade in Endangered Species of Wild Fauna and Flora (CITES). In order to supplement morphological identification of these species, a rapid chemical method of analysis was developed.

METHODS

Using Direct Analysis in Real Time (DART) ionization coupled with Time-of-Flight (TOF) Mass Spectrometry (MS), selected Dalbergia and common trade species were analyzed. Each of the 13 wood species was classified using principal component analysis and linear discriminant analysis (LDA). These statistical data clusters served as reliable anchors for species identification of unknowns.

RESULTS

Analysis of 20 or more samples from the 13 species studied in this research indicates that the DART-TOFMS results are reproducible. Statistical analysis of the most abundant ions gave good classifications that were useful for identifying unknown wood samples.

CONCLUSIONS

DART-TOFMS and LDA analysis of 13 species of selected timber samples and the statistical classification allowed for the correct assignment of unknown wood samples. This method is rapid and can be useful when anatomical identification is difficult but needed in order to support CITES enforcement. Published 2012. This article is a US Government work and is in the public domain in the USA.

Analysis of lipids with desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS) and desorption electrospray ionization-mass spectrometry (DESI-MS)

In this article, the effect of spray solvent on the analysis of selected lipids including fatty acids, fat-soluble vitamins, triacylglycerols, steroids, phospholipids, and sphingolipids has been studied by two different ambient mass spectrometry (MS) methods, desorption electrospray ionization-MS (DESI-MS) and desorption atmospheric pressure photoionization-MS (DAPPI-MS). The ionization of the lipids with DESI and DAPPI was strongly dependent on the spray solvent. In most cases, the lipids were detected as protonated or deprotonated molecules; however, other ions were also formed, such as adduct ions (in DESI), [M-H](+) ions (in DESI and DAPPI), radical ions (in DAPPI), and abundant oxidation products (in DESI and DAPPI). DAPPI provided efficient desorption and ionization for neutral and less polar as well as for ionic lipids but caused extensive fragmentation for larger and more labile compounds because of a thermal desorption process. DESI was more suitable for the analysis of the large and labile lipids, but the ionization efficiency for less polar lipids was poor. Both methods were successfully applied to the direct analysis of lipids from pharmaceutical and food products. Although DESI and DAPPI provide efficient analysis of lipids, the multiple and largely unpredictable ionization reactions may set challenges for routine lipid analysis with these methods.

Lipidomics in tissues, cells and subcellular compartments

Mass spectrometry (MS) advances in recent years have revolutionized the biochemical analysis of lipids in plants, and made possible new theories about the structural diversity and functional complexity of lipids in plant cells. Approaches have been developed to profile the lipidome of plants with increasing chemical and spatial resolution. Here we highlight a variety of methods for lipidomics analysis at the tissue, cellular and subcellular levels. These procedures allow the simultaneous identification and quantification of hundreds of lipids species in tissue extracts by direct-infusion MS, localization of lipids in tissues and cells by laser desorption/ionization MS, and even profiling of lipids in individual subcellular compartments by direct-organelle MS. Applications of these approaches to achieve improved understanding of plant lipid metabolism, compartmentation and function are discussed.

Rapid control of Chinese star anise fruits and teas for neurotoxic anisatin by Direct Analysis in Real Time high resolution mass spectrometry

After ingestion, products containing Chinese star anise (Illicium verum) contaminated or adulterated with Japanese star anise (Illicium anisatum) or other Illicium species, can cause epilepsy, hallucinations, and nausea due to the rare neurotoxic sesquiterpene dilactone anisatin that is present in Japanese star anise. Thus a rapid, simple and unambiguous method for distinguishing between the morphologically similar Chinese star anise and toxic Japanese star anise is important for food safety issues. Direct Analysis in Real Time (DART) ambient ionisation coupled with orbitrap high resolution mass spectrometry allowed the recording of mass spectra of anisatin in solid star anise fruits in seconds without any prior sample pretreatment. Spectra could be obtained in both positive ([M+NH(4)](+) at m/z 346.1496, C(15)H(24)NO(8)) and negative mode ([M-H](-) at m/z 327.1074, C(15)H(19)O(8)) and gave the same outcome provided a mass resolution of at least 27,000 is available. The anisatin signal was typically >1000 times larger in Japanese star anise than in Chinese star anise thus allowing an unequivocal qualitative determination. Herbal teas containing star anise fragments too small to be visually recognised, could be analysed by preparing a tea in 6 min and subsequently sampling ∼2 μL of tea on a glass rod. None of the 8 investigated retail teas contained significant quantities of anisatin. Spiking a complex herbal tea containing Chinese star anise with an equally concentrated tea prepared from Japanese star anise provided a linear calibration curve (R(2) ≥ 0.995) after normalising on a native constituent of Chinese star anise (standard addition method). This showed that adulteration down to 1% (w/w) is still measurable. Compared with existing PCR, TLC, GC-MS and HPLC-ESI-MS/MS procedures, the proposed DART-HRMS procedure is faster and simpler and moreover measures the actual biotoxin.

Infrared laser ablation sample transfer for MALDI imaging

An infrared laser was used to ablate material from tissue sections under ambient conditions for direct collection on a matrix assisted laser desorption ionization (MALDI) target. A 10 μm thick tissue sample was placed on a microscope slide and was mounted tissue-side down between 70 and 450 μm from a second microscope slide. The two slides were mounted on a translation stage, and the tissue was scanned in two dimensions under a focused mid-infrared (IR) laser beam to transfer material to the target slide via ablation. After the material was transferred to the target slide, it was analyzed using MALDI imaging using a tandem time-of-flight mass spectrometer. Images were obtained from peptide standards for initial optimization of the system and from mouse brain tissue sections using deposition either onto a matrix precoated target or with matrix addition after sample transfer and compared with those from standard MALDI mass spectrometry imaging. The spatial resolution of the transferred material is approximately 400 μm. Laser ablation sample transfer provides several new capabilities not possible with conventional MALDI imaging including (1) ambient sampling for MALDI imaging, (2) area to spot concentration of ablated material, (3) collection of material for multiple imaging analyses, and (4) direct collection onto nanostructure assisted laser desorption ionization (NALDI) targets without blotting or ultrathin sections.

Direct detection of additives and degradation products from polymers by liquid extraction surface analysis employing chip-based nanospray mass spectrometry

RATIONALE

Polymer-based surface coatings in outdoor applications experience accelerated degradation due to exposure to solar radiation, oxygen and atmospheric pollutants. These deleterious agents cause undesirable changes to the aesthetic and mechanical properties of the polymer, reducing its lifetime. The use of antioxidants such as hindered amine light stabilisers (HALS) retards these degradative processes; however, mechanisms for HALS action and polymer degradation are poorly understood.

METHODS

Detection of the HALS TINUVIN®123 (bis(1-octyloxy-2,2,6,6-tetramethyl-4-piperidyl) sebacate) and the polymer degradation products directly from a polyester-based coil coating was achieved by liquid extraction surface analysis (LESA) coupled to a triple quadrupole QTRAP® 5500 mass spectrometer. The detection of TINUVIN®123 and melamine was confirmed by the characteristic fragmentation pattern observed in LESA-MS/MS spectra that was identical to that reported for authentic samples.

RESULTS

Analysis of an unstabilised coil coating by LESA-MS after exposure to 4 years of outdoor field testing revealed the presence of melamine (1,3,5-triazine-2,4,6-triamine) as a polymer degradation product at elevated levels. Changes to the physical appearance of the coil coating, including powder-like deposits on the coating's surface, were observed to coincide with melamine deposits and are indicative of the phenomenon known as polymer 'blooming'.

CONCLUSIONS

For the first time, in situ detection of analytes from a thermoset polymer coating was accomplished without any sample preparation, providing advantages over traditional extraction-analysis approaches and some contemporary ambient MS methods. Detection of HALS and polymer degradation products such as melamine provides insight into the mechanisms by which degradation occurs and suggests LESA-MS is a powerful new tool for polymer analysis.

Ambient ionization-accurate mass spectrometry (AMI-AMS) for the identification of nonvisible set-off in food-contact materials

Set-off is the unintentional transfer of substances used in printing from the external printed surface of food packaging to the inner, food-contact surface. Ambient ionization-accurate mass spectrometry (AMI-AMS) detected and identified compounds from print set-off not visible to the human eye. AMI mass spectra from inner and outer surfaces of printed and nonprinted food packaging were compared to detect and identify nonvisible set-off components. A protocol to identify unknowns was developed using a custom open-source database of printing inks and food-packaging compounds. The protocol matched print-related food-contact surface ions with the molecular formulas of common ions, isotopes, and fragments of compounds from the database. AMI-AMS was able to detect print set-off and identify seven different compounds. Set-off on the packaging samples was confirmed using gas chromatographic-mass spectrometric (GC-MS) analysis of single-sided solvent extracts. N-Ethyl-2(and 4)-methylbenzenesulfonamide, 2,4-diphenyl-4-methyl-1(and 2)-pentene, and 2,4,7,9-tetramethyl-5-decyne-4,7-diol were present on the food-contact layer at concentrations from 0.21 to 2.7 ± 1.6 μg dm⁻², corresponding to nearly milligram per kilogram concentrations in the packaged food. Other minor set-off compounds were detected only by AMI-AMS, a fast, simple, and thorough technique to detect and identify set-off in food packaging.

Identification of isobaric amino-sulfonamides without prior separation

RATIONALE

Direct analysis mass spectrometry (DAMS) techniques offer increased speed of analysis without the need for sample preparation or prior separation. A feature of these techniques is that all ionisable species will typically be analysed at the same time which makes the ability to distinguish between isobaric compounds increasingly important.

METHODS

Investigations have been carried out to distinguish isomeric compounds by mass spectrometry only, without the use of any separation technique, in order to further understand the capabilities of DAMS techniques. The work focused on commercially available isomeric amino-sulfonamides, i.e. sulfalene, sulfameter, sulfamethoxypyridazine, sulfamonomethoxine, sulfadoxine, sulfadimethoxine, sulfisomidine, sulfamethazine, sulfamerazine, sulfaperine, sulfadiazine and sulfapyrazine.

RESULTS

All the isomeric compounds investigated could be distinguished from each other based on their tandem mass (MS/MS) spectrum or failing that, based on their MS(3) spectrum. Common fragmentation patterns/pathways were observed for groups of the sulfonamides and a rationale for the fragmentations observed is proposed. For the sulfonamides which contain a methoxy group on the pyrimidinyl, pyridazynil, or pyrazinyl ring, the fragmentation-directing feature is the positioning of the methoxy group in the ortho position of the ring with respect to the sulfonamide bond. The presence of an ortho substituent precludes the formation of the product ion resulting from the loss of aniline.

CONCLUSIONS

This work has demonstrated the usefulness of MS(n) fragmentation data in identifying and distinguishing isobaric structural isomers without the need for separation by high-performance liquid chromatography (HPLC), allowing the identification of compounds by DAMS techniques. This work has also highlighted patterns in the product ion data which has led to a postulation of how the protonation preference of a molecule can affect the product ions observed and how the presence of ortho substituents can affect this initial protonation preference.

DART-Orbitrap MS: a novel mass spectrometric approach for the identification of phenolic compounds in propolis

This is the first direct analysis in real-time mass spectrometry (DART-MS) study of propolis and a first study on the analysis of bee products using high-resolution DART-MS (DART-HRMS). Identification of flavonoids and other phenolic compounds in propolis using direct analysis in real-time coupling with Orbitrap mass spectrometry (DART-Orbitrap MS) was performed in the negative ion mode for minimizing the matrix effects, while the positive ion mode was used for the confirmation of selected compounds. Possible elemental formulae were suggested for marker components. The duration of one sample analysis by DART-MS analysis lasted ca. 30 s, and all benefits of high-resolution mass spectrometry were used upon data processing using the coupling of DART with the Orbitrap mass spectrometer. The possibility for scanning analysis of dried propolis extract spots on a planar porous surface was investigated in the heated gas flow of the DART ion source with adjustable angle. As an independent method, the approach of scanning analysis is of high interest and of future potential for confirmation of the results obtained from liquid sample analysis. Scanning analysis is highly promising for further development in the bioanalytical field due to the convenience of the storage and transportation of dried sample spots.

Optimization of direct analysis in real time (DART) linear ion trap parameters for the detection and quantitation of glucose

Presented here are findings for the development and optimization of a simple, high-throughput, and rapid method for the analysis of glucose. Because the applications of glucose and other six-carbon sugars is a growing field of interest especially in the production of biofuels, an efficient and rapid method for their quantitation from lignocelluloses is necessary. Glucose was analyzed using direct analysis in real time (DART) ionization and formed adducts (along with fragmentation) were observed with a linear ion trap (LIT) mass spectrometer. Since DART can be considered a complex thermal desorption ionization process, an optimization study of the helium gas temperature and introduction into the ionization region was performed. It was observed these parameters have a significant effect on the overall signal intensity as well as the signal-to-noise ratios in DART mass spectra. Using these optimized parameters, a set of different glucose concentrations (ranging from 10 to 3000  μM) were analyzed and used to determine a linear dynamic range (with the use of an internal standard). The analysis of the samples was done with minimal sample preparation and found to be reproducible on different days.