Portable imageless navigation system and surgeon's estimate for accurate evaluation of acetabular cup orientation during total hip arthroplasty in supine position

BACKGROUND

This prospective study aimed to clarify whether this novel device can evaluate the cup orientation during total hip arthroplasty (THA) more closely to that measured in postoperative computed tomography (CT) compared to the surgeon's estimate using a manual goniometer.

METHODS

We prospectively performed 30 cementless THAs via the anterolateral approach in supine position between October 2018 and July 2019, wherein cup orientation was evaluated by both a portable imageless navigation system (HipAlign) and a manual goniometer during surgeries. Primary outcome was the absolute estimate error [the absolute value of the difference between cup angles measured by postoperative CT and those measured by HipAlign (group H) or surgeon's estimate using the manual goniometer (group S) during surgery]. The number of outliers of the absolute estimate error (> 10°) in each group was also estimated.

RESULTS

The absolute estimate error of cup inclination in groups H and S was 3.3° ± 2.7° and 3.0° ± 2.5°, respectively (p = 0.51), whereas that of cup anteversion was 3.8° ± 3.4° and 6.0° ± 3.7°, respectively (p = 0.0008). The number of outliers of the estimate error in groups H and S was one case (3.3%) and six cases (20.0%), respectively (p = 0.04). In all six outlier cases, surgeons underestimated cup anteversion during surgeries.

CONCLUSIONS

This portable imageless navigation system was a useful method, especially for avoiding incorrect cup anteversion. Underestimation of cup anteversion during THA in the supine position with the conventional alignment assisting device should be given attention.

Effect of pelvic tilt and rotation on cup orientation in standing anteroposterior radiographs

BACKGROUND

Individual pelvic tilt and rotation have wide variability that can affect the measurement of cup orientation in anteroposterior (AP) radiographs. The purpose of this study was to analyse the effect of pelvic tilt and rotation on radiographic measurements of cup orientation.

METHODS

A total of 53 patients (63 hips) were included in this study. The patients underwent a computed tomography study with standing AP pelvis radiographs taken both preoperatively and approximately 3 months postoperatively. We used 2-dimensional/3-dimensional matching to measure the pelvic tilt and rotation, and the non-standardised and standardised cup orientation.

RESULTS

There was no difference in the pelvic tilt and rotation between the preoperative and postoperative radiographs. The distribution of the differences between the non-standardised and standardised cup anteversion exhibited a change within 5° in only 34/63 (54%) hips. The pelvic tilt correlated with the difference between the non-standardised and standardised cup anteversion, but the pelvic rotation did not. When all 63 hips were separated into the right and left sides, the pelvic rotation inversely correlated with the pelvic tilt-adjusted difference between the non-standardised and standardised cup anteversion of the right side but directly correlated with that of the left side.

CONCLUSIONS

The current study demonstrated that the measurement of cup anteversion in standing AP radiographs is significantly affected by both the pelvic tilt and pelvic rotation. An improved understanding of the pelvic orientation may eventually allow for desired cup positioning on a patient-specific basis to potentially reduce complications associated with the malposition of the cup.

Intraoperative evaluation of acetabular cup position during anterior approach total hip arthroplasty: are we accurately interpreting?

INTRODUCTION

Intraoperative radiographic evaluation during total hip arthroplasty (THA) has shown to improve the accuracy of acetabular component placement, however, differences in interpretation based on radiographic technique has not been established. This study aims to determine if differences exist in the interpretation of acetabular component abduction and anteversion between different radiographic projections.

METHODS

55 consecutive direct anterior THAs in 49 patients were prospectively enrolled. Target anteversion and abduction was defined by the Lewinnek zone. Fluoroscopy was used to direct acetabular component placement intraoperatively. After final cup implantation, fluoroscopic posterior-anterior hip and pelvis images were obtained for analysis. After completion of the procedure, an anterior-posterior plain pelvis radiograph was obtained in the operating room. Acetabulum component abduction and anteversion were postoperatively determined using specialised software on each of the 3 image acquisition methods.

RESULTS

Average acetabular cup abduction for intraoperative fluoroscopic posterior-anterior hip (FH), intraoperative fluoroscopic posterior-anterior pelvis (FP), and postoperative, standard, anteroposterior pelvis radiographs (PP) was 40.95° ± 2.87°, 38.87° ± 3.82° and 41.73° ± 2.96° respectively. The fluoroscopic hip and fluoroscopic pelvis tended to underestimate acetabular cup abduction compared to the postoperative pelvis (p < 0.001). Average acetabular cup anteversion for FH, FP, and PP was 19.89° ± 4.87°, 24.38° ± 5.31° and 13.36° ± 3.52° respectively. Both the fluoroscopic hip and fluoroscopic pelvis overestimated anteversion compared to the AP pelvis, with a 6.38° greater mean value measurement for FH (p < 0.001), and an 11° greater mean value measurement for FP (p < 0.001).

CONCLUSIONS

Fluoroscopic technique and differences between radiographic projections may result in discrepancies in component position interpretation. Our results support the use of the fluoroscopic posterior-anterior hip as the choice fluoroscopic imaging technique.

Supercapsular percutaneously-assisted total hip (SuperPath) versus posterolateral total hip arthroplasty in bilateral osteonecrosis of the femoral head: a pilot clinical trial

Background

The supercapsular percutaneously-assisted total hip arthroplasty (SuperPath) was proposed to be minimally invasive and tissue sparing with possible superior postoperative outcomes to traditional approaches of total hip arthroplasty (THA). Here, we compared the short-term outcomes of staged THA with the SuperPath or through posterolateral approach (PLA) for bilateral osteonecrosis of the femoral head (ONFH).

Methods

Patients with bilateral late-stage ONFH were prospectively recruited from our department from March 2017 to March 2018. Staged bilateral THAs with one side SuperPath and the other side PLA were performed consecutively in the same patients with right and left hips alternating within approaches. The average time interval between the staged THAs was 3 months. Perioperative status (operation time, incision length, intraoperative blood loss, soft tissue damage, and length of hospital stay) and postoperative function (range of motion, pain, and hip function) were recorded and compared between the SuperPath and PLA approaches within 12-month postoperatively.

Results

Four male patients (age, 51.00 ± 4.54; BMI, 21.49 ± 1.73) with bilateral alcohol-induced ONFH (Ficat III/IV) were followed up over 12 months postoperatively. Compared with the PLA, the SuperPath yielded shorter incision length (7.62 vs. 11.12 cm), longer operation time (103.25 vs. 66.50 min), more blood loss (1108.50 vs. 843.50 ml), deficient abduction angle of the acetabular cup (38.75° vs. 44.50°), and inferior early-term hip function (Harris hip score, 72.50 vs. 83.25) at 12-month postoperatively. Soft tissue damage, length of hospital stay, postoperative pain, postoperative range of motion, and 12-month patient satisfaction were comparable between both approaches.

Conclusion

The SuperPath may be a minimally invasive technique but the present study shows less favorable short-term outcomes than PLA for total hip arthroplasty in osteonecrosis of the femoral head. More investigations are required to provide convincing favorable evidences of the SuperPath over other traditional THA approaches.

Trial registration information

The trial was retrospectively registered in https://www.researchregistry.com (No. Researchregistry4993) on July 04, 2019. The first participant was enrolled on March 13, 2017.

Titanium Acetabular Component Deformation under Cyclic Loading

Acetabular cup deformation may affect liner/cup congruency, clearance and/or osseointegration. It is unclear, whether deformation of the acetabular components occurs during load and to what extent. To evaluate this, revision multi-hole cups were implanted into six cadaver hemipelvises in two scenarios: without acetabular defect (ND); with a large acetabular defect (LD) that was treated with an augment. In the LD scenario, the cup and augment were attached to the bone and each other with screws. Subsequently, the implanted hemipelvises were loaded under a physiologic partial-weight-bearing modality. The deformation of the acetabular components was determined using a best-fit algorithm. The statistical evaluation involved repeated-measures ANOVA. The mean elastic distension of the ND cup was 292.9 µm (SD 12.2 µm); in the LD scenario, 43.7 µm (SD 11.2 µm); the mean maximal augment distension was 79.6 µm (SD 21.6 µm). A significant difference between the maximal distension of the cups in both scenarios was noted (F(1, 10) = 11.404; p = 0.007). No significant difference was noted between the compression of the ND and LD cups, nor between LD cups and LD augments. The LD cup displayed significantly lower elastic distension than the ND cup, most likely due to increased stiffness from the affixed augment and screw fixation.

Accuracy of planar anteversion measurements using anteroposterior radiographs

Background

Several methods using simple anteroposterior (AP) radiographs have been suggested for the measurement of anteversion of the cup component after total hip arthroplasty. Herein, we compared six widely used anteversion measurement methods using two different types of AP radiograph, the conventional pelvis AP and hip-centered AP radiographs, to identify the measurement method and the type of radiograph that would provide the highest accuracy and reliability.

Methods

We developed two custom-made bi-planar anteversion measurement models for the validation test. The models were designed for pelvis AP and hip-centered AP radiographs, respectively. The radiographs were acquired using the inclination angles of both models, changing from 10° to 70° at 10° increments. For each inclination angle, anteversion was changed from 0° to 30° at 5° increments. The measurements were obtained independently by two orthopedic surgeons blinded from each other’s measurements, using the methods of 1) Pradhan et al., 2) Lewinnek et al., 3) Widmer et al., 4) Liaw et al., 5) Hassan et al., and 6) Ackland et al. The measurements were repeated after 2 months. The accuracy, compared with that of the reference angle, and intra-observer and inter-observer reliabilities of each method were calculated.

Results

The highest accuracy was found when the method of Liaw et al. was used with hip-centered AP radiographs, which showed a difference of 1.37° ± 1.73 from the reference angle. Moreover, regardless of the type of radiograph, the methods by Pradhan et al., Lewinnek et al., and Liaw et al. showed excellent correlations with the reference anteversion. However, substantial differences were found when the methods by Widmer et al., Hassan et al., and Ackland et al. were used, regardless of the type of radiograph used. When anteversion was measured in an inclination between 30° and 50°, the method of Pradhan et al., when used with pelvis AP radiographs, showed the highest accuracy (1.23° ± 0.92°). We also found no significant difference in anteversions between the measurements made on pelvic and hip-centered AP radiographs. Both interobserver and intraobserver reliabilities were high for all the measurements tested.

Conclusions

The methods by Pradhan et al., Liaw et al., and Lewinnek et al. may provide relatively accurate anteversion measurements with high reliability, regardless of the type of radiograph.

Inferior extended fixation utilizing porous titanium augments improves primary anti-rotational stability of the acetabular component

BACKGROUND

The primary anti-rotational stability is critical to preventing cup tilting failure following revision total hip arthroplasty, but is frequently compromised by severe ischial bone loss. A novel technique of "inferior extended fixation" was introduced by securing a porous metal augment into the deficient ischium. This study evaluated the effect of this technique on primary anti-rotational stability in revision total hip arthroplasty.

METHODS

Composite hemipelvis specimens, acetabular components and "lotus" augments were used to simulate total hip arthroplasty surgeries. Three different cementless operative settings of cup implantation were simulated: (1) native ischium without defects; (2) ischium with a defect not reconstructed; (3) ischial defect reconstructed with inferior extended fixation using a lotus augment. Lever-out testing was used to examine primary anti-rotational stability, which was measured as interface stiffness and yield moment.

FINDINGS

Compared with the native ischium setting, the mean interface stiffness decreased by 53.1% in the ischial defect setting (p < 0.001). In the inferior extended fixation setting, the mean value was 110% greater than that in the ischial defect setting (p = 0.014), and comparable to that in the native ischium setting (p = 1). Similar results were observed for the yield moment (declined by 63.1%, p < 0.001; 200% higher, p < 0.001; and p = 0.395; respectively).

INTERPRETATION

In revision total hip arthroplasty with severe ischial defects, inferior extended fixation with a lotus porous titanium augment restores anti-rotational stability of the acetabular component to the level of that with a native ischium, which provides the mechanical environment for bone ingrowth and prevents cup tilting failure.

New combined anteversion technique in hybrid THA: cup-first procedure with CT-based navigation

PURPOSE

Combined anteversion (CA) technique (stem-first procedure) is generally accepted as the optimal technique to attain an appropriate CA value in total hip arthroplasty (THA). However, cup anteversion is strongly influenced by the native femoral anteversion. Accordingly, anterior protrusion of the cup in the acetabulum might occur. The purpose of the present study is to investigate the achievement of the optimal CA while avoiding anterior cup protrusion and examine the significance of our new CA technique with cup-first procedure in hybrid THA.

METHODS

Seventy-nine hybrid THAs with the cup-first procedure used a CT-based navigation system for cup positioning. In the preoperative planning, cup anteversion was aimed at approximately 20°. However, in actuality, sufficient cup coverage in the original acetabulum based on individual anatomy is given priority over cup placement based on CT-based planning to ensure adequate cup coverage. The target stem anteversion was determined following Widmer's mathematical formula (37.3 = femoral stem anteversion × 0.7 + cup anteversion). Cemented stem was inserted according to the target stem anteversion angle.

RESULTS

Regarding the assessment of overall alignment, the calculated Widmer's CA values during surgery and postoperative CT evaluation were 34.1° ± 6.0° (range 20.7°-51.2°) and 35.1° ± 6.7° (range 21.6°-50.7°). There were 72 hips (91.1%) within 25°-50° of CA. Cup protrusion length averaged 2.0 mm ± 2.6 mm (0-8.8 mm) in the axial view and 0.4 mm ± 1.0 mm (0-3.6 mm) in the sagittal view. Cup protrusion length of more than 5 mm was indicated in 10 hips, and no hips observed more than 10 mm.

CONCLUSION

Our new CA technique (cup-first procedure) with hybrid THA was able to achieve optimal CA value while avoiding anterior cup protrusion.

Comparative study of stem anteversion using a cementless tapered wedge stem in dysplastic hips between the posterolateral and anterolateral approaches

BACKGROUND

In total hip arthroplasty (THA), the concept of combined anteversion is accepted as one of best indicators of prosthetic joint stability. Technical parameters may influence the stem and cup anteversion. We therefore investigated if stem anteversion could be influenced by surgical approaches in cementless THA using a tapered wedge stem with stem-first technique.

HYPOTHESIS

We postulated that the type of approach, posterolateral (PLA) or anterolateral approach (ALA), would influence stem anteversion in dysplastic hip patients. We asked (1) whether stem anteversion was higher in the PLA group and (2) how postoperative stem anteversion was correlated to preoperative femoral anteversion in each group.

PATIENTS AND METHODS

We retrospectively compared two groups of hips that underwent THA using a tapered wedge stem with the posterolateral (PLA group; 154 hips) or anterolateral (ALA group; 81 hips) approaches. Computed tomography was utilized to measure femoral neck and stem anteversion. To investigate related factors that affect stem anteversion, a stepwise regression analysis was performed.

RESULTS

The stem anteversion in the PLA and ALA groups was 43.7°±9.8° and 34.0°±12.3°, respectively (p<0.01). The stepwise selection process resulted in a model involving femoral neck anteversion and surgical approach (p<0.01). The stem anteversion of the ALA group (r=0.75, p<0.01) was better correlated to femoral neck anteversion than that of the PLA group (r=0.52, p<0.01).

DISCUSSION

The stem implantation through the ALA is thought to be more restricted than that through the PLA due to the difference of difficulty in femoral exposure. Tapered wedge stems, which are relatively thin and flat, have a high degree of freedom in the femoral canal. Consequently, in cementless THA using a tapered wedge stem, the surgical approaches affected stem anteversion differently. Stem anteversion was more anatomically restored to femoral neck anteversion through the ALA than through the PLA.

LEVEL OF EVIDENCE

III, retrospective case-control study.

The Accuracy of the Computed Tomography-Based Navigation System in Total Hip Arthroplasty Is Comparable With Crowe Type IV and Crowe Type I Dysplasia: A Case-Control Study

BACKGROUND

Clinical outcomes of total hip arthroplasty (THA) for Crowe type IV are poorer than for Crowe type I, because it is more difficult to accurately position the acetabular components. This study aimed to examine the accuracy of the computed tomography (CT)-based navigation system for acetabular component positioning in primary THA for Crowe type IV.

METHODS

From 2006 to 2018, 29 patients who underwent 34 primary THAs for Crowe type IV were enrolled in the "Type IV" group and 32 patients who underwent 34 THAs for Crowe type I were enrolled in the "Type I" group, formed by matching patients in the Type IV group on age, gender, body mass index, and surgical approach. We investigated (1) the accuracy of the cup size between that at preoperative planning and that actually implanted and (2) the mean deviation of the cup angle and 3-dimensional position of acetabular components between preoperative plan and postoperative records.

RESULTS

The accuracy of the cup size was 79.4% and 94.1% in the Type IV and Type I groups, respectively, without a statistically significant change detected (P = .075). The mean deviations of the cup angle and 3-dimensional position were comparable in both groups.

CONCLUSION

Using the CT-based navigation system, it was possible to accurately implant the acetabular component for Crowe type IV, and the accuracy was comparable to that for Crowe type I. The CT-based navigation system is a useful intraoperative tool to accurately implant the acetabular component, especially with severe pelvic deformities such as Crowe type IV.

Isolated acetabular revision with femoral stem retention using computed tomography-based navigation

BACKGROUND

In isolated acetabular revision surgery, surgeons must place the cup at an appropriate angle with various retained stem anteversion angles to prevent postoperative dislocation. For accurate acetabular cup position, various navigation systems have been used. Nevertheless, no publications have reported combined cup and stem anteversion and dislocation rates after isolated acetabular revision, especially comparing the use of navigation with manual implantation. Therefore we performed a retrospective comparative study to answer the following questions: (1) What is the combined anteversion after isolated acetabular revision with computed tomography-based navigation? (2) Does navigation improve the accuracy of cup angle and combined anteversion, (3) reduce dislocation rate, and (4) reduce operative time?

HYPOTHESIS

A navigation system makes combined anteversion near the target angle in isolated acetabular revision.

PATIENTS AND METHODS

We conducted a retrospective study of 32 hips in 24 patients who underwent isolated acetabular revision total hip arthroplasty using computed tomography-based navigation system. The control group comprised 8 hips in 8 patients who underwent the same procedure without navigation.

RESULTS

In the navigation group, average Widmer's combined anteversion was 39.0°±8.7° (range, 25.3°-56.6°). Cup positions were 40.3°±2.9° (range, 29.0°-49.0°) for radiographic abduction angle, 24.3°±8.0° (range, 4.6°-42.6°) for radiographic anteversion. In the control group, Widmer's combined anteversion was 47.2°±15.1° (range, 27.0°-74.3°, p=0.048). The average cup positions for radiographic abduction angle and anteversion were 36.7°±8.9° (range, 24.5°-54.9°) and 29.1°±7.3° (range, 17.2°-38.8°), respectively (p>0.05). Widmer's combined anteversion deviated from the target angle by a smaller amount in the navigation group than in the control group: errors in measurement of Widmer's combined anteversion were 7.2°±5.1° (range, 0.74°-19.6°) in the navigation group and 13.9°±11.1° (range, 3.6°-37.3°) in the control group (p=0.135). Postoperative dislocation occurred in none of the 32 hips (0%) in the navigation group and in one of the 8 hips (12.5%) in the control group (p=0.2).

DISCUSSION

Using the navigation system, combined anteversion is made near the target angle in isolated acetabular revision surgery and more accurately than manual implantation. These results should be considered as preliminary since this is a limited cohort, but it brings new knowledge in navigation considering the very limited number of series using of navigation in isolated cup revision of total hip arthroplasty. In addition this is the first study to investigate combined cup and stem anteversion in isolated acetabular revision. The use of CT-scan is helpful to diagnose error in stem anteversion and to adapt the orientation of the new cup.

LEVEL OF EVIDENCE

III, Retrospective case control study.

Intraoperative measurement of cup inclination using fluoroscopy requires a correction factor

INTRODUCTION

Malpositioning of the cup in total hip arthroplasty (THA) is associated with dislocation, early polyethylene wear, and impingement. The direct anterior approach (DAA) THA allows for intraoperative fluoroscopy imaging (IF). The current study investigates the following research hypotheses: (1) intraoperative measurements of radiographic cup inclination (RI) are reliable and reproducible. (2) A correction factor can compensate for the complex parallax effects when using IF.

METHODS

In 2016, 100 consecutive hips underwent primary THA utilizing DAA and IF for cup placement. RI was measured on intraoperative fluoroscopy images and postoperative AP pelvis radiographs.

RESULTS

Determination of RI on IF images is reliable and reproducible (ICC 0.851-0.950). RI measurement on IF images had a good correlation with the corresponding postoperative RI on AP pelvis radiographs (r = 0.538, p < 0.001). However, intraoperative RI measurements are on average 4.9° lower compared to postoperative measurements (SD 2.5°).

CONCLUSION

Intraoperative fluoroscopy is a reliable tool to measure RI during DAA THA. The surgeon needs to apply a 5°. correction factor to the intraoperative measurements to adjust for parallax.

Long-term survival of hybrid total hip arthroplasty with the uncemented CLS cup, cemented Müller cobalt-chromium stem, and 28-mm Metasul™ bearings: Retrospective review of 115 hips after a minimum of 17.8 years

BACKGROUND

Hard-on-hard bearings require a meticulous implantation technique but may be associated with lower wear rates in young active patients. Among them, metal-on-metal (MoM) bearings have been blamed for specific complications including adverse reactions to metal debris and metal hypersensitivity. These complications have been chiefly reported with large-head MoM implants (except when used for hip resurfacing). Most of the published data on small-head MoM implants were obtained using uncemented stems. To our knowledge, no information on outcomes beyond 15 years is available for small-head MoM implants with cemented cobalt-nickel-chromium (Co-Ni-Cr) stems, which might increase the risk of complications. The objective of this study was to collect long-term follow-up data on patients who underwent hybrid total hip arthroplasty (THA) with 28-mm MoM Metasul™ bearings in order to assess: (1) long-term survival (based on the revision rate), (2) and the occurrence of adverse reactions to metal debris documented during revision.

HYPOTHESIS

Survival of 28-mm Metasul™ bearings used with hybrid THA is acceptable.

PATIENTS AND METHODS

A single-centre retrospective study was conducted in consecutive patients managed using 28-mm Metasul™ bearings in a press-fit cup, with a cemented Co-Ni-Cr stem. Follow-up was at least 17 years. The clinical and radiographic data were analysed. Mean age at surgery was 57.3±7.9 years (range, 29.6-75.3 years).

RESULTS

The study included 115 hips with a mean follow-up of 20.3±0.8 years (range, 17.8-21.6 years). Survival to revision for any reason was 86.10% (95% CI, 79.8-92.4%) and survival to revision for aseptic loosening was 92.6% (95% CI, 87.7-97.6). Half the specimens obtained during revision showed a macrophage reaction and a non-specific inflammatory infiltrate. No patient experienced complications specifically related to the use of Metasul™ bearings with a cemented Co-Ni-Cr stem.

DISCUSSION

Long-term survival of 28-mm MoM Metasu™ bearings was close to that of metal-on-polyethylene bearings and lower than that of ceramic-on-ceramic or small-head MoM bearings in other studies. No complications specifically related to the use of small-head MoM bearings with a cemented Co-Ni-Cr stem were recorded.

LEVEL OF EVIDENCE

IV, retrospective study.

Periacetabular osteotomy using three-dimensional cutting and reposition guides: a cadaveric study

The goal of periacetabular osteotomy (PAO) is to reorient the acetabulum in a more physiological position. Its realization remains challenging regarding the final position of the acetabulum. Assistance with custom cutting- and reorientation-guides would thus be very helpful. Our purpose is to present a pilot study on such guides. Eight cadaveric hemipelvis were scanned using CT. After segmentation, 3D models of each specimen were created, a PAO was virtually performed and reorientation of the acetabula were defined. A specific guide was designed aiming to assist in iliac, posterior column and superior pubic ramus cuts as well as in acetabulum reorientation. Furthermore, the acetabular position was planned. Three-dimensional printed guides were used to perform PAO using the modified Smith-Peterson approach. The post-operative CT images and virtually planned acetabulum reorientation were compared in terms of acetabular index (AC), lateral centre edge angle (LCE), acetabular anteversion angle (AcetAV). There was no intra-articular or posterior column fracture seen. Two cadavers showed very low bone quality with insufficient stability of fixation and were excluded from further analysis. Correlation between the post-operative result and planning of the six included cadavers revealed the following mean deviations: 5° (SD ±3°) for AC angle, 6° (SD ±4°) for LCE angle and 15° (SD ±11°) for AcetAV angle. The use of 3D cutting and reorientation blocks for PAO was possible through a modified Smith-Peterson approach and revealed accurate fit to bone, accurate positioning of the osteotomies and acceptable planned corrections in cadavers with good bone quality.

Calcium Phosphate Bone Graft Substitutes with High Mechanical Load Capacity and High Degree of Interconnecting Porosity

Bone graft substitutes in orthopedic applications have to fulfill various demanding requirements. Most calcium phosphate (CaP) bone graft substitutes are highly porous to achieve bone regeneration, but typically lack mechanical stability. This study presents a novel approach, in which a scaffold structure with appropriate properties for bone regeneration emerges from the space between specifically shaped granules. The granule types were tetrapods (TEPO) and pyramids (PYRA), which were compared to porous CaP granules (CALC) and morselized bone chips (BC). Bulk materials of the granules were mechanically loaded with a peak pressure of 4 MP; i.e., comparable to the load occurring behind an acetabular cup. Mechanical loading reduced the volume of CALC and BC considerably (89% and 85%, respectively), indicating a collapse of the macroporous structure. Volumes of TEPO and PYRA remained almost constant (94% and 98%, respectively). After loading, the porosity was highest for BC (46%), lowest for CALC (25%) and comparable for TEPO and PYRA (37%). The pore spaces of TEPO and PYRA were highly interconnected in a way that a virtual object with a diameter of 150 µm could access 34% of the TEPO volume and 36% of the PYRA volume. This study shows that a bulk of dense CaP granules in form of tetrapods and pyramids can create a scaffold structure with load capacities suitable for the regeneration of an acetabular bone defect.

Is the alignment guide technique in total hip arthroplasty sufficient for accurate cup positioning with a modified Watson Jones approach?

PURPOSE:

Cup setting with only an alignment guide has been reported to be inaccurate in the lateral decubitus position in total hip arthroplasty (THA). We assessed the accuracy of cup positioning using only the alignment guide technique via a modified Watson Jones approach in the lateral decubitus position.

METHODS:

Two hundred hips of 189 patients underwent THA from October 2014 to September 2016 via a modified Watson Jones approach. In the final sample, 181 hips of 171 patients (35 males, 136 females) were included in this investigation. The alignment of the cup was evaluated by an anteroposterior radiograph of the pelvis 1 week after surgery. Measurements were divided into safe zone determined by Callanan and Lewinnek.

RESULTS:

There were 168 (92.8%) acetabular cups that were placed within the safe zone for both inclination and anteversion based on the safe zones defined by Lewinnek, and 134 (74%) acetabular cups that were placed within the safe zone defined by Callanan. Multiple logistic analysis showed that the laterality and the addition of the confirmation method were indicators for malpositioning of combined inclination and anteversion.

CONCLUSION:

Our data suggested that even if special tools were not used in the lateral decubitus position, using only the alignment guide enabled cup positioning to be achieved with 92.8% accuracy in the Lewinnek safe zone and 74% accuracy in the Callanan safe zone. Multiple logistic analysis showed that the laterality and the addition of a confirmation alignment guide influenced the accuracy of cup positioning.

Deformation of acetabular press-fit cups: Influence of design and surgical factors

BACKGROUND

Deformation of acetabular cups when press-fitted into an undersized cavity is inevitable due to the inhomogeneous stiffness of acetabular bone. Thinner cups or screw holes might increase the risk of high cup deformation. The aim of this study was to examine the influence of cup design and liner assembly on the deformation response during cup implantation.

METHODS

Acetabular cups with different designs were implanted into polyurethane foam models simulating the anatomical situation with nominal press-fits of 1mm and without nominal press-fits (line-to-line). Deformations were determined using a tactile coordinate measuring machine. A 3D laser scanner was used to determine the contact conditions at the cup-cavity interface. Polyethylene and ceramic liners were assembled to the implanted cups and the influence of the insertion on the deformation response evaluated. Fixation strength of the cups was determined by push-out testing.

FINDINGS

Cup deformation increased with smaller wall thickness (P < 0.037) and screw holes (P < 0.001). Insertion of ceramic liners reduced the deformation (P < 0.001), whereas polyethylene liners adapted to the deformation of the implanted cups (P > 0.999). Thin-walled cups exhibited a higher fixation strength for similar implantation forces (P = 0.011).

INTERPRETATION

Thin-walled cups achieved higher fixation strengths and might be more bone-preserving. However, in combination with screw holes and high press-fit levels, wall thickness should be considered carefully to avoid excessive cup deformations leading to potential complications during liner assembly. Line-to-line insertion of thin-walled cups should be accompanied with a rough surface coating to minimize the loss of fixation strength due to the low press-fit fixation.

A precise method for determining acetabular component anteversion after total hip arthroplasty

AIMS

Several radiological methods of measuring anteversion of the acetabular component after total hip arthroplasty (THA) have been described. These are limited by low reproducibility, are less accurate than CT 3D reconstruction, and are cumbersome to use. These methods also partly rely on the identification of obscured radiological borders of the component. We propose two novel methods, the Area and Orthogonal methods, which have been designed to maximize use of readily identifiable points while maintaining the same trigonometric principles.

PATIENTS AND METHODS

A retrospective study of plain radiographs was conducted on 160 hips of 141 patients who had undergone primary THA. We compared the reliability and accuracy of the Area and Orthogonal methods with two of the current leading methods: those of Widmer and Lewinnek, respectively.

RESULTS

The 160 anteroposterior pelvis films revealed that the proposed Area method was statistically different from those described by Widmer and Lewinnek (p < 0.001 and p = 0.004, respectively). They gave the highest inter- and intraobserver reliability (0.992 and 0.998, respectively), and took less time (27.50 seconds (sd 3.19); p < 0.001) to complete. In addition, 21 available CT 3D reconstructions revealed the Area method achieved the highest Pearson's correlation coefficient (r = 0.956; p < 0.001) and least statistical difference (p = 0.704) from CT with a mean within 1° of CT-3D reconstruction between ranges of 1° to 30° of measured radiological anteversion.

CONCLUSION

Our results support the proposed Area method to be the most reliable, accurate, and speedy. They did not support any statistical superiority of the proposed Orthogonal method to that of the Widmer or Lewinnek method. Cite this article: Bone Joint J 2019;101-B:1042-1049.

The synergetic effect of pelvic rotation and X-ray offset on radiographic angles of the acetabular cup

The objective of this study is to investigate the synergetic effect of the pelvic rotation and X-ray offset on the radiographic anteversion/inclination (RA/RI) angles of the acetabular cup using a mathematical model. A cone model for establishing the spatial relationship between a three-dimensional (3D) circle and its two-dimensional (2D) elliptical projection is utilized to quantify the relationship between the 3D RA/RI angles of the cup and their 2D counterparts with different types of pelvic rotations in pelvic/hip anteroposterior radiographs. The results reveal that the effect of inlet/outlet views on the 2D RA angle is similar to that of iliac/obturator views. The permissible ranges of pelvic rotation for the 2D RA angle with an acceptable bias are the 3D space formed by the limits of triple axial rotations. For a specified acceptable bias of the 2D RA angle, these ranges are almost equal between pelvic and hip radiographs. The combined inlet/obturator or outlet/iliac views can maintain the 2D RA angle of a pelvic radiograph within the same range of acceptable bias as that of a hip radiograph. For a 2D RA angle with an acceptable bias, the permissible range of pelvic rotation needs to be evaluated with equal attention in both radiographs. Graphical abstract The traditional methods for calculating the radiographic angles of the acetabular cup are based on the ellipse projection of the opening circle of the cup on radiographs. However, with varying locations of the X-ray source and pelvis rotations about different axes, the outline of this ellipse projection will change, and accordingly, the traditional method and calculating results will be inaccurate. In this study, a cone model for three-dimensional circle-to-two-dimensional ellipse projection is utilized to incorporate the effect of X-ray offset and quantify the relationships of the radiographic angles of the cup with the true orientation of the cup and pelvic rotations in either pelvic or hip anteroposterior radiographic situation.

Changes in acetabular component alignment due to screw fixation in patients with hip dysplasia

INTRODUCTION

Adequate initial stability of the acetabular cup is essential for total hip arthroplasty (THA). However, changes in the alignment of the acetabular component caused by screw fixation are concerning in patients with inadequate bone stock. This study aimed to investigate the effects of screw fixation on the alignment of the acetabular component in THA patients with hip dysplasia.

METHODS

We retrospectively examined 256 hips (range 28-87 years) that underwent THA using a navigation system. Patients were divided into 2 groups based on the presence or absence of changes in the alignment of the intraoperative acetabular cup, and univariate and multivariate analyses were performed to identify factors that were predictive of changes in acetabular component alignment after screw fixation in 2 dimensions: inclination and anteversion.

RESULTS

Screw fixation led to a mean change in inclination of 1.6° (range 0-10°) and a mean change in anteversion of 1.4° (range 0-14°). The Crowe classification, the presence of bone cysts, and the use of an inferior quadrant screw were identified as factors that correlated with acetabular cup alignment changes in inclination (odds ratios, 6.01, 5.94 and 0.03, respectively). Only the Crowe classification was identified as a factor that correlated with intraoperative alignment changes in anteversion (odds ratio, 2.08).

CONCLUSIONS

Screw fixation altered the acetabular cup alignment. The inclination changes were related to the extent of the dysplasia, and the risk was reduced when the inferior quadrant screw was used. Surgeons should use caution during screw fixation in THAs performed on severely dysplastic hips.

Total hip arthroplasty with accolade/trident through the direct minimally invasive anterior approach without traction table: Learning curve and results after a minimum of 5 years

BACKGROUND

The direct minimally invasive anterior approach (DMIAA) in total hip arthroplasty (THA) is widely accepted. In our department the DMIAA according to Rachbauer together with the Trident cup and Accolade stem was introduced in 2004. The purpose of the study was to demonstrate the five-year results and to analyze the learning curve of a new introduced approach.

PATIENTS AND METHODS

Between July 2004 and May 2006, a consecutive series of 151 THA in 147 patients was retrospectively analyzed. All patients were planned to received a THA with the Accolade/Trident implant system using the DMIAA without traction table. Clinical and radiographic data, complications and survivorship were documented with a follow-up of at least 5 years.

RESULTS

Regarding cup implantation, there were 11 (7.3%) failed intentions to treat due to missing pressfit (8 cases) and acetabular floor perforation (3 cases). No failed intentions to treat occurred during stem implantation. Total implant survival after 5 years follow-up after exclusion of 11 cases with failed intention to treat (N=140) was 96.9% (SD 1.4; CI 94.3-99.6). After exclusion of the failed intentions to treat (N=140, N=4 in the first 20 cases), there was significant (p<0.001) difference between the first 16 implants with a 5 year-survival of 83.2% (SD 8.6; CI 66.4-100) and 95.7% (SD 0.9; CI 93.9-97.5) for the following 124 implants. Radiolucent lines were observed in Gruen zone 1 in 3.3% and in Gruen zone 1 and 2 in 1.1%.

DISCUSSION

THA with Accolade/Trident using the DMIAA without traction table according to Rachbauer temporary exposed patients to a higher risk of implant revisions, which was normalized after the first 20 cases. Results of the learning curve are comparable to other techniques using an orthopaedic traction table. After the typical learning curve, the rate of 5 years implant failure is in accordance with the registry data for non-cemented implants. The Accolade stem showed minimal radiographic signs of radiolucency.

LEVEL OF EVIDENCE

IV, retrospective, consecutive case series.

Supine versus lateral position for accurate positioning of acetabular cup in total hip arthroplasty using the modified Watson-Jones approach: A randomized single-blind controlled trial

BACKGROUND

The orientation of the acetabular cup is a critical factor for prevention of various postoperative complications in total hip arthroplasty (THA). Although most patients are treated in either supine or lateral position during surgery, it is still unclear which position is superior to achieve more accurate cup positioning. Our study was conducted in order to answer the following questions: (1) does the supine position provide a higher accuracy of cup positioning than the lateral position in THA using modified Watson-Jones approach? (2) is there any difference in the distribution of cup position between the two positions? Hypothesis Our hypothesis was that the supine position would provide a higher accuracy of cup positioning than the lateral position in THA using modified Watson-Jones approach.

PATIENTS AND METHODS

A single-center prospective randomized study (registration number: UMIN000021627) was conducted between May 2016 and December 2017. We recruited a total of 60 participants undergoing unilateral primary cementless THA using modified Watson-Jones anterolateral approach based on the result of the sample size calculation. They were randomly assigned to either supine position (n=29) or lateral position (n=31). The cup alignment was targeted using a goniometer during surgery. The radiographic cup inclination was targeted to 40° and the radiographic cup anteversion was targeted considering the femoral stem anteversion during surgery. Postoperative cup alignment was measured by plain radiography and computed tomography. We defined the difference between postoperative and target cup angle as target error and our primary outcome was the absolute value of the target angle. As secondary outcome, the distribution of the target error was evaluated. The target errors of each inclination and anteversion were divided into 3 groups; neutral (-3°≤the target error≤3°), positive error (3°<the target error), and negative error (the target error<-3°).

RESULTS

The assessment of primary outcome for all recruited patients showed that supine group was significantly more accurate than lateral group in terms of radiographic inclination (2.4° vs. 4.5°, respectively, mean difference 2.1°; 95% confidence interval, 0.7 to 3.5; p<0.01). There was no significant difference in terms of radiographic cup anteversion (5.6° vs. 5.2°, mean difference 0.4°; 95% confidence interval, -1.8 to 2.6; p=0.69). The rate of positive error of anteversion in supine and lateral group was larger than that of negative value of anteversion (51.7% vs. 10.3% and 48.4% vs. 12.9%, respectively). Any acute complication (dislocation, fracture, and infection) was not found in both groups during postoperative 3 months.

DISCUSSION

In this randomized-controlled trial, higher accuracy of acetabular cup inclination was provided by supine position than by lateral position in THA. On the other hand, there was no significant difference between both groups in terms of cup anteversion. In both groups, most cups were placed with larger anteversion than we targeted. Modified Watson-Jones approach in both positions should be performed considering these results.

STUDY REGISTRATION NUMBER

UMIN000021627. Level of evidence II, randomised controlled study (population-limited).

Anatomic stem inserted according to native anteversion could reproduce the native anterior distance of the femoral head and decrease bony impingement in total hip arthroplasty

PURPOSE

To investigate whether anatomic and straight stems could reproduce the anteroposterior distance (AD) of the native femoral head and evaluate the effect of AD of the femoral head on range of motion (ROM) and bony impingement.

METHODS

This retrospective simulation study included 64 patients who had undergone primary total hip arthroplasty between 2012 and 2014. Using computed tomography (CT)-based templating software, anatomic and straight stems were inserted with same alignment. AD of the head centre was compared between the two stems and native anatomy. Furthermore, post-operative ROM was calculated, and correlation between AD and ROM was assessed.

RESULTS

There was a strong positive correlation between native anteversion (mean 21.9°) and anatomic stem anteversion (mean 22.5°) (R = 0.975, P < 0.001). There was no significant difference in AD between the native and anatomic stems (mean 37.7 and 38.8 mm, respectively), but AD of the straight stem was significantly lower than that of the native and anatomic stems. The straight stem showed a significantly lower ROM in flexion and internal rotation angles with 90° flexion (IR) than the anatomic stem (P < 0.05 and P < 0.001, respectively). AD showed a stronger correlation with ROM of IR than with stem anteversion.

CONCLUSIONS

The anatomic stem could reproduce AD of the native femoral head centre, but the head centre of the straight stem in the same anteversion with anatomic stem translated significantly posterior, significantly decreasing the ROM of flexion and IR and increasing bony impingement of IR. To avoid bony impingement and acquire sufficient ROM, reproducing AD was important.

In vivo kinematic analysis of replaced hip during stationary cycling and computer simulation of optimal cup positioning against prosthetic impingement

BACKGROUND

Dynamic hip kinematics during stationary cycling after total hip arthroplasty (THA) have been unclear. Furthermore, no computer simulation of optimal cup position based on in vivo kinematics has yet been assessed.

METHODS

This study consisted of 7 patients who underwent unilateral primary THA for symptomatic osteoarthritis. Using a flat-panel X-ray detector, continuous radiographs were obtained during stationary cycling. We analyzed the three-dimensional replaced hip kinematics from the top to the bottom position of the crank using image-matching techniques and quantified minimum liner-to-stem neck distance. Simulation analyses with in vivo kinematics were performed to examine patient-specific optimal cup placement against prosthetic impingement.

FINDINGS

During stationary cycling, pelvis showed 27.1° of posterior tilt on average without significant change. Hip flexed by 59.4° and 19.3° on average at the top and bottom positions, respectively. Minimum liner-to-neck distance was 8.8 mm on average at the bottom position. Liner-to-neck, bone-to-bone, or bone-to-component impingement was not observed at any positions in any hips. Simulation analysis of cup placement showed that larger cup anteversion, inclination, and use of elevated liner significantly decreased the minimum distance between posterior liner and stem neck. Cup anteversion of more than 30° with elevated liner could cause posterior liner-to-neck impingement at bottom position.

INTERPRETATION

Stationary cycling after THA provides no excessive hip range of motion or liner-to-neck contact. Cup placement and use of elevated liner significantly influence the minimum liner-to-neck distance, in some cases simulating posterior prosthetic impingement.

A Preoperative Analytical Model for Patient-Specific Impingement Analysis in Total Hip Arthroplasty

Prosthetic impingement is important to consider during total hip arthroplasty planning to minimise the risk of joint instability. Modelling impingement preoperatively can assist in defining the required component alignment for each individual. We developed an analytical impingement model utilising a combination of mathematical calculations and an automated computational simulation to determine the risk of prosthetic impingement. The model assesses cup inclination and anteversion angles that are associated with prosthetic impingement using patient-specific inputs, such as stem anteversion, planned implant types, and target Range of Motion (ROM). The analysed results are presented as a range of cup inclination and anteversion angles over which a colour map indicates an impingement-free safe zone in green and impingement risk zones in red. A validation of the model demonstrates accuracy within +/- 1.4° of cup inclination and anteversion. The study further investigated the impact of changes in stem anteversion, femoral head size, and head offset on prosthetic impingement, as an example of the application of the model.

Component positioning and ceramic damage in cementless ceramic-on-ceramic total hip arthroplasty

BACKGROUND

In ceramic-on-ceramic (CoC) total hip arthroplasty (THA), component positioning demonstrated to influence the bearing damage: however the connection between angles and clinical outcomes at long-term follow-ups is currently lacking. Aims of this study were: the computer tomography (CT) assessment of component positioning in CoC THAs; the correlation analysis between positioning and ceramic damage; the identification of safe zones.

METHODS

91 consecutive post-operative CT scans including two types of CoC implants, with a mean follow-up of 12 ± 4.4 years, were evaluated. III generation (74.2%) and IV generation (25.8%) CoC surfaces were included. The angle measurements (cup abduction, anteversion, cup tilt, stem antetorsion, sacral slope) were automated using a CT-based software. The combined anteversion was assessed as well as the cup-neck position at -15°, 0°, 45° and 90° of flexion. Ceramic damage was diagnosed using synovial fluid analyses and radiological criteria.

RESULTS

63.7% of THAs was inside the cup abduction target 30°-45° and 68.1% was inside the cup anteversion target 5°-25°. 19 patients (20.9%) showed signs of ceramic damage. High cup abduction and high cup-neck 45° minimum angle (which stood for high abduction and extreme combined version) significantly correlated with ceramic damage. No demographical features apart III generation ceramic bearings influenced the results. No safe zones could be detected.

CONCLUSIONS

In CoC THA, no safe zones can be described. However it is important to avoid cup inclination over 45° and a combination of steep cup and extreme combined version.

Influence of Spinopelvic Alignment on Pelvic Tilt after Total Hip Arthroplasty

Objective

To evaluate the impact of spinopelvic parameters and hip contracture on change in the pelvic tilt (PT) after Total hip arthroplasty (THA).

Methods

One hundred patients (15 male and 85 female) who underwent THA were included in this prospective study. Radiographic data were obtained preoperatively and 1 year after THA. Radiographic parameters included sagittal anterior pelvic plane (APP), sagittal vertical axis (SVA), sacral slope (SS), pelvic inclination (PI), and lumbar lordosis angle (LL). The APP was defined as the angle between the anterior pelvic plane and the vertical plane. A positive value indicates pelvic retroversion. Postoperative changes in PT were divided into three groups: the PA group (pelvic anteversion, ΔAPP < −5°), the PR group (pelvic retroversion, ΔAPP > 5°), and the PT group (minimal change, ΔAPP ≤ ± 5°). The Kruskal–Wallis test and the Steel–Dwass test were used to compare the preoperative and postoperative spinopelvic parameters among the three groups. The Spearman's rank correlation coefficient was used to evaluate the correlation between ΔAPP and spinopelvic parameters.

Results

Minimal change in pelvic tilt was observed in 59% of patients, while pelvic anteversion was observed in 16% of patients and pelvic retroversion was observed in 25% of patients. There were no significant changes in the spinopelvic parameters, including TK, LL, SVA, LL, SS, and APP after THA. The Femoral angle (FA) was significantly decreased after THA (P < 0.001). Preoperative APP was significantly more retroverted in the PA group than the PR group, and the PT group (6.8 ± 12.2, 0.2 ± 9.9, −8.3 ± 8.3, P < 0.001). Preoperative SS, PI‐LL, and PI were significantly smaller in the PA group than the PT group and the PR group. A significant negative correlation was identified between preoperative APP and ΔAPP (r = −0.418, P < 0.001).

Conclusion

Approximately 60% of the patients did not have any marked change in PT after THA. Preoperative APP was the only predictive factor associated with marked anterior or posterior change in PT.

Low dislocation rate of Saturne®/Avantage® dual-mobility THA after displaced femoral neck fracture: a cohort study of 966 hips with a minimum 1.6-year follow-up

INTRODUCTION

Dislocation is a serious and common complication and a great concern with the use of total hip arthroplasty (THA) when treating displaced femoral neck fracture (FNF). Dual-mobility (DM) THA might reduce the dislocation risk. We aim to report the dislocation and revision rate of primary DM THA in patients with displaced FNF.

MATERIALS AND METHODS

Between 2005 and 2015, 966 consecutive patients (676 women) at mean age 80.5 years (range 42-104) with displaced FNF were operated with DM articulation THA by posterolateral approach (PLA). Patient files and radiographs were evaluated for dislocations, revisions, and other complications until death of the patient or August 1st, 2017. Data were crosschecked with the National Patient Registry. Patient's mental state was tested upon admissions. Surgeon's educational level was noted and post-operative cup position was measured.

RESULTS

At minimum 1.6-year follow-up, there were 45 (4.7%) dislocations and eight (0.8%) cup revisions. The 30-day mortality was 9.2% and 533 patients (55.2%) were dead at the time of last follow-up. We observed eight intraprosthetic dislocations (IPD); six occurred in relation to closed reduction. Cementless stem fixation was associated with higher dislocation risk (p = 0.04) and higher rate of stem complications (p = 0.002). There was no significant association between cognitive impairment and dislocation (OR 2.0, 95% CI 0.96-4.34, p = 0.06).

CONCLUSION

Overall, DM THA inserted via PLA results in an acceptable dislocation risk and low revision rate in fragile, old patients with acute FNF fracture, regardless of mental status. A unique complication in DM THA is IPD, which requires an immediate open reduction surgery.

Accuracy of acetabular cup placement using CT-based navigation in total hip arthroplasty: Comparison between obese and non-obese patients

BACKGROUND

In obese patients, malpositioning of the acetabular cup increases the risk of dislocation in total hip arthroplasty (THA). The aim of this study was to determine whether obesity affects the accuracy of acetabular cup positioning using a computed tomography (CT)-based navigation system.

METHODS

We retrospectively evaluated 226 consecutive patients who underwent cementless primary THAs assisted by the CT-based hip navigation system. We divided the patients into three groups according to body mass index (BMI) and examined the difference between preoperative planning and postoperative implantation angles from CT data.

RESULTS

There was no significant correlation between BMI and both inclination and anteversion differences (R = 0.028 and R = 0.045, respectively). There were no significant differences among the BMI < 25, 25 ≦ BMI < 30, and BMI ≧ 30 groups (p value: 0.725, 0.934, respectively); between the BMI < 25 and BMI ≧ 25 groups (p value: 0.542, 0.697, respectively); and between the BMI < 30 and BMI ≧ 30 groups with regard to inclination and anteversion (p value: 0.859, 0.456, respectively). Moreover, similar findings were observed with regard to the distance between the preoperative planning and postoperative cup positioning for the transverse, anteroposterior, and craniocaudal axes of the pelvis.

CONCLUSION

We found that the accuracy of acetabular cup placement using CT based-navigation in THA was not affected in obese patients. Therefore, THAs with a CT-based navigation system are considered useful in obese patients.

The optimal combined anteversion pattern to achieve a favorable impingement-free angle in total hip arthroplasty

BACKGROUND

There have been no studies on the differences in impingement-free angle that result from different combined anteversion (CA) patterns. The aim of this study was to find the optimal CA pattern for achieving a favorable impingement-free angle, including bony and prosthetic impingement, in total hip arthroplasty.

METHODS

We evaluated 100 patients with no hip arthritis. We investigated the impingement-free angle (flexion, internal rotation with 90° flexion, extension, and external rotation) after changing the stem and cup anteversions to satisfy several CA patterns [cup anteversion + stem anteversion = 30°, 40°, 50°, and 60°; cup anteversion + 0.7 × stem anteversion = 37.3° (:Widmer's theory); and cup anteversion + 0.77 × stem anteversion = 43.3° (:Yoshimine's theory)] using 3-dimensional templating software.

RESULTS

The impingement-free angle changed dramatically among the various CA patterns. The optimal CA was changed by various stem anteversion. Only CA: Widmer with stem anteversion of 20° satisfied daily-life range of motion (ROM) requirements (flexion ≥130°, internal rotation with 90° flexion ≥ 45°, extension ≥ 40°, external rotation ≥ 40°).

CONCLUSION

Good impingement-free angle cannot be obtained with single fixed CA. Different CA patterns should be used, depending on the differences in the stem anteversion. A CA of 30° with 0° ≤ stem anteversion ≤10°; a CA:Widmer with 20° of stem anteversion; a CA of 40° or Widmer with 30° of stem anteversion. When stem anteversion is ≥40°, CA should be decided by each patient's state. Among them, a stem anteversion of 20° with cup anteversion of 23.3° was found to be the best CA pattern.

Dislocation of large-diameter head metal-on-metal total hip arthroplasty and hip resurfacing arthroplasty

INTRODUCTION

Dislocation of large-diameter head (LDH) metal-on-metal (MoM) total hip arthroplasty (THA) or hip resurfacing arthroplasty (HRA) is a rare complication. This study aimed to determine the incidence and risk factors for dislocation of LDH MoM THAs and HRAs.

METHODS

This retrospective analysis considered 4038 cementless LDH MoM THAs and HRAs, 3207 THAs in 2912 patients and 831 HRAs in 757 patients. The end of follow-up was revision due to dislocation. Incidence of dislocation was evaluated from this study population of 4038, and study groups were formed. The study was designed as a case-control study, and a threefold stratified randomised control group was formed. Demographic data were collected and radiological analyses were performed in the study groups.

RESULTS

There were 26/3207 (0.8%) early dislocations in the THA group, and 6/831 (0.7%) in the HRA group ( p = 0.9). Most LDH THA dislocations occurred in a group with head size ⩽ 38 mm (18/26) ( p < 0.001). In dislocated hips, there were more dysplastic acetabula and post-traumatic hips than in the control group ( p = 0.036). In the dislocation group, the mean acetabulum component anteversion angle was 19.6° (standard deviation [SD] 13.4°) and in the control group it was 23.2° (SD 10.4°) ( p = 0.006); 7/32 (21.8%) of dislocated THAs needed revision surgery, and mean time to revision from the index surgery was 1.2 (SD 2.6) years.

DISCUSSION

Dislocations occurred more often in THAs of head size ⩽ 38 mm and with a smaller anteversion angle of the acetabulum component. Hip dysplasia and post-traumatic osteoarthritis were more common in patients with dislocation.

Subject-Specific Surgical Planning for Hip Replacement: A Novel 2D Graphical Representation of 3D Hip Motion and Prosthetic Impingement Information

Prosthetic impingement (PI) following total hip arthroplasty (THA), which arises due to the undesirable relative motion of the implants, results in adverse outcomes. Predicting PI through 3D graphical representation is difficult to comprehend when all activities are combined for different implant positions. Therefore, the aim of the paper was to translate this 3D information into a 2D graphical representation for improved understanding of the patient’s hip motion. The method used planned implanted geometry, positioned onto native bone anatomy, and activity definitions as inputs to construct the 2D polar plot from 3D hip motion in four steps. Three case studies were performed to highlight its potential use in (a) combining different activities in a single plot, (b) visualising the effect of different cup positions and (c) pelvic tilt on PI. A clinical study with 20 ‘Non-Dislocators’ and 20 ‘Dislocators’ patients after 2 years of THA was performed to validate the method. The results supported the study hypothesis, in that the incidence of PI was always higher in the ‘Dislocators’ compared to the ‘Non-Dislocators’ group. The proposed 2D graphical representation could assist in subject-specific THA planning by visualising the effect of different activities, implant positions, pelvic tilt and related aspects on PI.

Outcome of a hemispherical porous-coated acetabular component with a proximally hydroxyapatite-coated anatomical femoral component

Aims

We previously reported the long-term results of the cementless Duraloc-Profile total hip arthroplasty (THA) system in a 12- to 15-year follow-up study. In this paper, we provide an update on the clinical and radiological results of a previously reported cohort of patients at 23 to 26 years´ follow-up.

Patients and Methods

Of the 99 original patients (111 hips), 73 patients (82 hips) with a mean age of 56.8 years (21 to 70) were available for clinical and radiological study at a minimum follow-up of 23 years. There were 40 female patients (44 hips) and 33 male patients (38 hips).

Results

All acetabular and femoral components were well fixed and showed signs of bone ingrowth. Nine acetabular components were revised due to wear-osteolysis-related problems and four due to late dislocation. The probability of not having component revision at 25 years was 83.2% (95% confidence interval (CI) 74.5 to 91.8; number at risk 41). Acetabular osteolysis was observed in ten hips. The mean femoral head penetration was 1.52 mm (sd 0.8) at 15 years and 1.92 mm (sd 1.2) at 25 years. Receiver operating characteristic (ROC) analysis revealed that mean femoral penetration with a value of 0.11 mm/year or more was associated with the appearance of osteolysis. The 25-year Kaplan–Meier survival with different endpoints was 89.9% for acetabular osteolysis (95% CI 83.3 to 96.5), 92.1% for proximal femoral osteolysis (95% CI 86.1 to 98.2), and 75.5% for femoral osteopenia (95% CI 66.5 to 84.5).

Conclusion

The Duraloc-Profile THA system showed excellent long-term bone fixation. Nevertheless, monitoring is recommended in order to detect wear and late dislocations in this population that was relatively young at the time of surgery. Cite this article: Bone Joint J 2019;101-B:378–385.

Non-equivalent Results from Different Anteversion Measurements Methods for the Evaluation of the Acetabular Cup Orientation in Total Hip Arthroplasty

Objective

To determine the comparability among 10 radiographic anteversion methods for acetabular cup orientation in total hip arthroplasty (THA) found in the literature and the “gold” standard of assessing the anteversion with CT.

Methods

This is a retrospective study that blindly compares 10 different conventional radiographic anteversion measurements with the “gold” standard, the measurement of anteversion on the transverse plane of the 3‐D images made with CT. The patient archiving and communications system (PACS) was systematically searched for subjects that had undergone a CT angiogram of the abdomen and lower extremities, including the pelvis, had at least one THA in situ and had undergone anterior‐posterior (AP) and cross‐lateral pelvic radiography between January 2013 and August 2016 in the Diakonessenhuis Hospital Utrecht/Zeist, a non‐academic institution. CT scans of patients (n = 16) were systematically collected. Three observers independently measured cup anteversion from radiographs, using a total of 10 different methods, and measured the “gold” standard on CT images. The outcomes of the 10 radiographic anteversion were compared in terms of linear correlation with the “gold” standard on CT images.

Results

The correlations of the radiographic measured anteversions with the “gold” standard measured on CT images were 0.528 for the method of Liaw, 0.556 for Wan, 0.562 for the cross‐lateral method, 0.586 for Hassan, 0.594 for Dorr, 0.602 for Lewinnek, 0.624 for Widmer, 0.671 for the lateral CT, 0.747 for Ackland, and 0.771 for the method of Riten Pradham.

Conclusion

Anteversion measurement methods represent different projectional angles of the acetabular cup in different planes around different axes. Therefore, they differ from the “gold” standard and are not interchangeable, as is shown by this study. We consider the anatomical anteversion in the transverse plane rotating around the longitudinal axis as the “gold” standard and recommend avoiding using the term anteversion for other projectional angles in different planes.

Comparison of G-guide and Image-free Navigation System in Accuracy of Stem Anteversion Assessment During Total Hip Arthroplasty

Introduction:

We have developed and utilized the Gravity-guide (G-guide) as a simple manual instrument for intraoperative assessment and adjustment of stem anteversion (AV). Since 2013, we simultaneously measured stem AV using the G-guide and image-free navigation during THA procedure. The purpose of this study was to compare the measurement accuracy of the G-guide and navigation system using the postoperative CT results as a reference.

Methods:

In total, 59 hips in 56 patients who underwent primary THA using both the G-guide and image-free navigation system were included in the study. All patients underwent postoperative CT examination, and the femoral stem AV was assessed using a 3D image analysis system (Zed hip, LEXI, Japan). The AV angle derived from the postoperative CT image analysis was used as the reference value to assess the accuracy of the two intraoperative measurement systems.

Results:

The discrepancy between the G-guide and the postoperative CT-measured values averaged 5.0° ± 3.9°, while the corresponding value for the navigation system was 5.2° ± 4.1°. Acceptable accuracy with a measurement error of less than 10° was achieved in 86% and 90% of the cases for the G-guide and navigation measurements respectively.

Conclusion:

Consequently, it was shown that both navigation and G-guide measurements can achieve comparative accuracy and are clinically useful.

Influence of surgical approach on final outcome in total hip arthroplasty for osteoarthritis in patients older than 80 years

Purpose

We compared the outcome of total hip arthroplasty (THA) in this age group using direct anterior or posterior approach.

Methods

We performed a retrospective analysis following consecutive primary THA in patients over 80 years.

Results

The DAA group demonstrated significantly shorter length of stay, better functional improvement, no dislocation or revision while PA group required two revisions due to dislocation.

Conclusions

The use of DAA for THA in the elderly was associated with shorter hospitalization and superior functional outcomes in the early post-operative period, and had a lower rate of dislocation without increasing risk of early revision.

Assessment of acetabular version in total hip arthroplasty: an application of Widmer's technique in a regional setting

BACKGROUND

Acetabular prosthesis positioning in total hip arthroplasty is important in reducing the risk of dislocation. Assessment of version by computed tomography scan is expensive and involves a large radiation dose. We wished to assess the value of Widmer's technique, utilizing readily available radiographs, to determine cup anteversion.

METHODS

Patients who underwent primary total hip arthroplasty by the senior author (AGS) at a single regional hospital over a 5-year period were eligible for inclusion. Measurements were performed using the technique described by Widmer, utilizing standard post-operative radiographs. Statistical analysis was undertaken in SPSS v22. Significance was accepted at P < 0.05.

RESULTS

Assessment included 109 hips in 99 patients; 63 hips with cemented cups and 46 hips with uncemented cups. Mean acetabular anteversion in the cemented group was 11.9° (0-27.7, SD: 7) and in the uncemented group was 14.1° (10.3-32.7, SD: 7.1); this difference trended towards statistical significance (P = 0.09). Test-retest measurements showed high degree of correlation (Pearson test: 0.927, P < 0.001). There were 96 of 109 hips positioned in the Lewinnek safe zone of 5-25° anteversion. The crude dislocation rate in our cohort was 6.4% (7 of 109 hips) with all dislocations occurring in hips placed in the safe zone.

CONCLUSION

Widmer's technique is a reliable method for calculating acetabular version in a regional hospital setting and offers the individual surgeon a ready technique of personal quality control. Cup version was not a significant factor contributing to dislocation rates in our series.

Incidence, risk factors and prognosis of transient pseudosubluxation after total hip arthroplasty

INTRODUCTION:

Pseudosubluxation is a transient separation of the prosthetic femoral head from the acetabular liner during the anaesthetic period after total hip arthroplasty (THA). However, little is known about the frequency, pathomechanism, risk factors or natural history.

METHODS:

To determine the incidence, direction of the displacement, risk factors and subsequent instability of pseudosubluxation, we evaluated 1099 primary cementless THAs (943 patients), which were performed during 8 years at one institution. Immediately after THA, postoperative radiographs were obtained for all hips. If a subluxation was noted, the operated hip was examined by fluoroscope within 1 hour of the detection and repeat radiographs were taken on the postoperative day 1.

RESULTS:

The pseudosubluxation was identified in 2.6% (28/1059). All of the 28 heads subluxed anteriorly and reduced in flexion-internal rotation. In multivariate analysis: (1) operative decrease of the femoral offset (odds ratio; 1.161 (95% confidence interval [CI]; 1.077-1.251), p = 0.001); and (2) medialisation of acetabular cup (odds ratio; 3.402 (95% CI; 1.482-7.813), p = 0.009) were found as risk factors for pseudosubluxation. None of the 28 hips dislocated during 3- to 8-year follow-up.

CONCLUSIONS:

Our results provide information about the incidence, risk factors and natural history of pseudosubluxation after primary THA. Surgeons should be aware of the risk of pseudosubluxation when performing THA in patients with coxa vara, who have a large femoral offset, and in those with dysplastic or deficient acetabulum, who have a lateral centre of rotation.

The influence of cavity preparation and press-fit cup implantation on restoring the hip rotation center

BACKGROUND

Reaming of the acetabular cavity and cup implantation directly influence the hip rotation center and contact area between implant and bone. Previous studies have reported on an altered rotation center after total hip arthroplasty, but have not studied the influence of reaming and cup implantation separately. Aim of this study was therefore to analyze the individual influence of acetabular reaming and subsequent cup implantation on the rotation center and how this influences the contact conditions at the bone-implant interface.

METHODS

Acetabular press-fit cups were implanted into the left and right hips of three full cadavers (n = 6). CT scans were performed to calculate the change in hip rotation center after reaming and prior to liner insertion. 3D models of the cups were used to determine the polar gap, the contact conditions and the effective press-fit.

FINDINGS

Reaming the acetabular cavity shifted the rotation center medially (median 5.8 mm, range 4.8-9.1), superiorly (5.3 mm, 3.0-7.0) and posteriorly (2.9 mm, 1.0-5.3). With cup implantation, the rotation center shifted back towards the native position, but no full restoration was observed. The degree of shift increased with the size of polar gap (r_s = 0.829, P = .042), which inversely reduced the contact area (r_s = 0.886, P = .019).

INTERPRETATION

This study reveals that the dominant factor in hip rotation center restoration is the reaming process, while the cup implantation for a given nominal press-fit has only a small influence. Increasing the press-fit would improve the restoration but bares the danger of insufficient bone coverage and periprosthetic fractures due to the high forces needed.

G, H.P. H. BMCRI method for measuring cup anteversion after total hip replacement

STUDY DESIGN

Prospective clinical study.

BACK GROUND

In total hip replacement the cup placement is critical. Orientation is determined by anteversionand abduction. We have devised a simple geometrical method to calculate anteversion using simple instruments which does not require complicated conversion tables, scientific calculators, trigonometric tables and special x ray equipment.

OBJECTIVES

The aim of study is to evaluate the new method in terms of reliability and validity in comparison with other commonly used radiological methods against CT evaluation.

METHODOLOGY

In 30 hips of 25 consecutive patients, 13 females and 12 males who underwent primary total hip replacement in our institution, the component version in our method was calculated and compared with CT evaluation of angles. The intra and inter observer reliability were assessed.

RESULTS

Average CT measurement was 23.28 for ante version.We found our method had good correlation with CT calculation with average variability of +/_ 3.913800 in planar anteversionand CT methods had excellent intra and inter observer reliability (C.I. = 0.884 to 0.947&0.866 to 0.963).

CONCLUSION

Our method is accurate in comparison with CT (P value > 0.05), which does not need any reference tables, conversiontables, scientific calculators, multiple radiation exposures and not time consuming.

Efficacy of Computed Tomography-Based Navigation for Cup Placement in Revision Total Hip Arthroplasty

Background

Navigation systems are an effective tool to improve the installation accuracy of the cup in primary total hip arthroplasty. This study aimed to evaluate the efficacy of a computed tomography-based navigation system in achieving optimal installation accuracy of implants in revision total hip arthroplasty and to clarify the usefulness of the navigation system.

Methods

We conducted a retrospective study of 23 hips in 23 patients who underwent revision total hip arthroplasty using a computed tomography-based navigation system; the control group comprised 33 hips in 33 patients who underwent revision total hip arthroplasty without a navigation system.

Results

The average cup position with the navigation system was 40.0° ± 3.7° in radiographic abduction angle, 18.8° ± 4.8° in radiographic anteversion, and 41.2° ± 8.9° in combined anteversion; without the navigation system, the average cup position was 38.7° ± 6.1°, 19.0° ± 9.1°, and 33.6° ± 20.5°, respectively. The achievement rate of cup positioning within the Lewinnek safe zone was not significantly different between the navigation group (82.6%) and control group (63.6%). In contrast, the achievement rate of cup positioning within the Widmer combined anteversion guidelines was significantly greater in the navigation group (78.3%) than in the control group (48.0%, p = 0.029). Furthermore, outlier cases in the navigation group had a smaller variance of deviation from the optimal cup position than those in the control group did.

Conclusions

The results show that the use of navigation for revision total hip arthroplasty improved cup positioning and reduced the range of outliers. Improvement of cup placement accuracy influenced the installation of the stem and also improved the achievement rate of combined anteversion. Thus, a computed tomography-based navigation system is very useful for surgeons when placing the cup within the target angle in revision total hip arthroplasty.

Direct Anterior Approach Total Hip Arthroplasty Using a Morphometrically Optimized Femoral Stem, a Conventional Operating Table, Without Fluoroscopy

BACKGROUND

Our experience with direct anterior approach total hip arthroplasty (THA) suggests that it can be performed successfully with a morphometrically optimized metaphyseal-diaphyseal engaging femoral stem (NOT a short stem), a regular operating room table (NOT a special custom table), and WITHOUT intraoperative fluoroscopy. We report our minimum 2-year results.

METHODS

A retrospective review of a single-surgeon series of primary direct anterior approach THAs was performed. All procedures were performed on a regular table, without fluoroscopy, using a cementless tapered femoral stem. Clinical, functional, and radiographic outcomes were evaluated at a minimum of 2 years.

RESULTS

In total, 1017 primary THAs were performed. The preoperative Harris Hip Score was 40.7 ± 5.1 and improved to 95.3 ± 4.2 at minimum 2-year follow-up. There were 3 dislocations (0.3%) and 15 revisions (1.5%): 7 for infection (0.7%), 4 for periprosthetic fractures (0.4%), 2 for instability (0.2%), 1 for loosening (0.1%), and 1 for pain (0.1%). Five patients (0.5%) required blood transfusion. One patient developed deep vein thrombosis and pulmonary embolism. No intraoperative fractures, perforation, or THA-related mortality occurred. Neutral stem alignment was confirmed in 98.3%. Mean cup inclination was 38.8° ± 5.1° and anteversion was 16.2° ± 3.5°. The mean leg-length discrepancy was corrected from 1.2 ± 0.2 cm preoperatively to 0.2 ± 0.1 cm postoperatively.

CONCLUSION

Using a morphometrically optimized metaphyseal-diaphyseal engaging tapered femoral stem instead of a short stem reduces component malposition and minimizes risk of loosening. Combining the use of this implant design and the technique and elements described in our cohort demonstrated to have excellent results at 2 years. The patients will need continued follow-up to demonstrate further durability of this device and technique compared to others performing direct anterior THA.

A new radiographic acetabular cup anteversion measurement method in total hip arthroplasty: a clinical study

BACKGROUND

The acetabular cup positioning is one of the most crucial steps affecting stability and wear rates in total hip arthroplasty. Different methods have been described for determining the anteversion of the acetabular cup in the literature. But there is still not a widely accepted method to assess the acetabular anteversion radiography. The aim of this study is to measure the acetabular anteversion angle on a single pelvis AP radiography with our method which was proven with an experimental study before.

MATERIALS AND METHODS

A total of 15 patients (8 males, 7 females) who underwent total hip arthroplasty and have had a pelvis computed tomography scans in our outpatient clinic were evaluated retrospectively. The anteversion angle was calculated in all of pelvis CT scans. For radiological measurement, the formula defined by the authors in an experimental model previously was used.

RESULTS

Statistically significant difference was not determined between radiographic and CT-based measurements (p = 0.207; p > 0.05). A statistically significant agreement was observed at a level of 98.8% between radiographic and CT-based measurements (ICC = 0.988; 95% CI 0.966-0.996; p < 0.01).

CONCLUSION

Assessment of the acetabular cup anteversion is very important to predict the possible complications after total hip arthroplasty. Although many methods have been defined for this purpose, each of these has advantages and disadvantages. In particular, with computed tomography method, the patient is exposed to excessive radiation, whereas we think that our method is a preferred method due to features not requiring additional equipment, low radiation exposure, being simple, cost-effectiveness, easily applicable and almost 100% accurate.

Total hip arthroplasty using stem-first technique with navigation: the potential of achievement of the optimal combined anteversion being a risk factor for anterior cup protrusion

PURPOSE

In the combined anteversion (CA) technique for total hip arthroplasty (THA) with a cementless stem, cup anteversion is strongly influenced by the native femoral anteversion. It is hypothesized that in cases with large native femoral anteversion, cup anteversion can be decreased, and anterior cup protrusion from the anterior edge of the acetabulum could occur due to the achievement of optimal CA. In this study, the accuracy of CA in THA with the CA technique using imageless navigation and the relationship between the protrusion of the anterior edge of cup and optimum CA was retrospectively evaluated.

METHODS

Ninety-seven patients (104 hips) who underwent primary THA by the CA technique using image-free navigation were enrolled in the study. The femoral stem was placed following the individual femoral anteversion so that the target cup anteversion could be determined following a mathematical formula (37 = femoral stem anteversion × 0.7 + cup anteversion). Results The resulting CA values effectively achieved accurate CA with 39.49 ± 5.03° postoperatively. On the other hand, anterior cup protrusion was measured by computed tomography image. A cup protrusion length of more than 3 mm was indicated for 60 cases (57.7%). All included patients were divided into two groups: Group 1 as protrusion positive and Group 2 as protrusion negative. In Group 1, preoperative femoral anteversion and postoperative stem anteversion were significantly higher, while postoperative cup anteversion was significantly lower. However, the postoperative CA value indicated no significant difference between the groups.

CONCLUSIONS

The CA (stem-first) technique with image-free navigated THA could effectively achieve accurate CA. On the other hand, a large number of cases revealed anterior cup protrusion due to the low cup anteversion.

Plain radiography findings to predict dislocation after total hip arthroplasty

Background

With the improvements of modern surgical techniques and hip prosthesis, the causes for dislocation after total hip arthroplasty (THA) have changed. The aim of this retrospective analysis was to identify new plain radiography findings to predict dislocation after THA.

Methods

Five thousand five hundred thirteen consecutive primary THAs performed between January 2000 and December 2014 were reviewed through a nested case–control study design. Among them, 38 patients with 39 hip dislocations (dislocation group) were selected and matched to 78 hips in 78 patients without dislocation (control group). The factors that might influence the prosthetic stability were identified by univariate analyses, and a multivariate logistic regression analysis was performed to determine the odds ratio of each factor.

Results

The difference of the cup position was not statistically significant. The newly identified risk factors were the following: preoperative hip adduction deformity combined with limb lengthening of 2 cm postoperatively; a knee valgus combined with pelvic obliquity deformity and bilateral pathological hips.

Conclusions

Patients with soft tissue imbalance, across joint deformity around hips and bilateral pathological hips seem more predisposed to suffer from dislocation after THA. Appropriate surgical intervention strategies along with meticulously postoperative management may help preventing dislocation after THA.

The translational potential of this article

A better understanding of the probable causes of dislocation after THA proposed a new clinical application of plain radiography. This radiography-related clinical research may reveal the novel mechanism of dislocation after THA and new preventive measures.

Lack of consensus on optimal acetabular cup orientation because of variation in assessment methods in total hip arthroplasty: a systematic review

INTRODUCTION:

Dislocation is 1 of the main reasons for revision of total hip arthroplasty but dislocation rates have not changed in the past decades, compromising patients' well-being. Acetabular cup orientation plays a key role in implant stability and has been widely studied. This article investigates whether there is a consensus on optimal cup orientation, which is necessary when using a navigation system.

METHODS:

A systematic search of the literature in the PubMed, Embase and Cochrane databases was performed (March 2017) to identify articles that investigated the direct relationship between cup orientation and dislocation, including a thorough evaluation of postoperative cup orientation assessment methods.

RESULTS:

28 relevant articles evaluating a direct relation between dislocation and cup orientation could not come to a consensus. The key reason is a lack of uniformity in the assessment of cup orientation. Cup orientation is assessed with different imaging modalities, different methodologies, different definitions for inclination and anteversion, several reference planes and distinct patient positions.

CONCLUSIONS:

All available studies lack uniformity in cup orientation assessment; therefore it is impossible to reach consensus on optimal cup orientation. Using navigation systems for placement of the cup is inevitably flawed when using different definitions in the preoperative planning, peroperative placement and postoperative evaluation. Further methodological development is required to assess cup orientation. Consequently, the postoperative assessment should be uniform, thus differentiating between anterior and posterior dislocation, use the same definitions for inclination and anteversion with the same reference plane and with the patient in the same position.