Behavior of glucose oxidase immobilized in various electropolymerized thin films

Enzymatic preparation of oxidized viscose fibers-based biosorbent modified with ε-polylysine for dyes removal and microbial inactivation

A novel fiber-based biosorbent for dyes removal and microbial inactivation was prepared by enzymatic oxidization of viscose fibers and further modification with ε-polylysine. Glucose oxidase (GOx) was first employed as the enzyme for oxidation of viscose fibers. The consequences illustrated that the hydroxyl group on C1 position of viscose fibers was successfully oxidized with oxidation ratio of 2.43 ± 0.31%. Subsequently, ε-polylysine with average molecular weight of 4.44 ± 1.13 KDa and antimicrobial activity to E. coli of 90.48 ± 1.64 was modified with oxidized viscose fibers by lipase. Experimental results showed that oxidized viscose fibers were successfully modified with ε-polylysine with optimum degree of modification (DM) of 13.56 ± 1.05%. This oxidized viscose fiber modified with ε-polylysine (OVF-PL) displayed good dyes adsorption (or dyes removal) capacity for both anionic and cationic dyes, especially for anion dyes. Furthermore, OVF-PL showed excellent antimicrobial activity against E. coli and B. subtilis, particularly for E. coli, with GIB of 92.65%. Such fiber-based may offer a new pathway for preparing economical and efficient biosorbent for environmental remedy purpose.

The isotope method for the determination of stoichiometry between compounds forming the polypyrrole and glucose oxidase composite

Stable isotope ratio mass spectrometry is a conventional method used in archaeology, and medical, environmental and paleoenvironmental reconstruction studies. However new insights and applicability of the equipment often open new research areas and improve our understanding of the ongoing processes. Therefore the stable isotope ratio mass spectrometry method was applied for the stoichiometry determination of the complex polypyrrole and glucose oxidase composite (PPy-GOx composite). The enzyme glucose oxidase and conducting polymer polypyrrole were reported to form a composite, which was evaluated in time using the dynamic light scattering method. The consistent enlargement of the PPy-GOx composite and the relative decrease of the spare enzyme molecules were observed in the polymerization solution. UV-VIS spectrometry was employed to follow the polymerization process. The isotope mixing model was applied for the evaluation of the constitution of the PPy-GOx composite. According to the obtained results the determination of the PPy-GOx composite stoichiometry could be more reliably determined using the nitrogen isotope ratio approach in comparison to the carbon approach. We expect that this novel work will widen the applications of stable isotope ratio mass spectrometry in research.

Biomedical Perspectives of Polyaniline Based Biosensors

Electrically conducting polymers (ECPs) are finding applications in various fields of science owing to their fascinating characteristic properties such as binding molecules, tuning their properties, direct communication to produce a range of analytical signals and new analytical applications. Polyaniline (PANI) is one such ECP that has been extensively used and investigated over the last decade for direct electron transfer leading towards fabrication of mediator-less biosensors. In this review article, significant attention has been paid to the various polymerization techniques of polyaniline as a transducer material, and their use in enzymes/biomolecules immobilization methods to study their bio-catalytic properties as a biosensor for potential biomedical applications.

Immobilization of glucose oxidase onto gelatin for biosensor construction

The properties of a glucose biosensor made by immobilization of glucose oxidase onto gelatin in a layer of electrochemically deposited polyaniline have been investigated. Glucose oxidase was immobilized within gelatin cross-links with chromium(III) acetate. The glucose oxidase biosensor was developed by forming a polyaniline-deposited electrode surface as support for the immobilized enzyme gel, in order to increase its durability. The polyaniline/gelatin/glucose oxidase biosensor has been characterized using chemical and electrochemical methods. Temperature, pH, cross-linking agent concentration, enzyme concentration, kinetic properties, reusability and the effect of electro-active compounds were among the parameters studied. The response time of the glucose oxidase biosensor is 90 s, the detection limit is below 1 mmol/dm3 and the sensor can be used 20 times within a 2-month period without losing its stability.

Polymeric Sensor Materials: Toward an Alliance of Combinatorial and Rational Design Tools?

Increased selectivity, response speed, and sensitivity in the chemical and biological determinations of gases and liquids are of great interest. Particular attention is paid to polymeric sensor materials, which are applicable to sensors exploiting various energy transduction principles, such as radiant, electrical, mechanical, and thermal energy. Ideally, numerous functional parameters of sensor materials can be tailored to meet specific needs using rational design approaches. However, increasing the structural and functional complexity of polymeric sensor materials makes it more difficult to predict the desired properties. Combinatorial and high-throughput methods have had an impact on all areas of research on polymer-based sensor materials including homo- and copolymers, formulated materials, polymeric structures with engineered morphology, and molecular shape-recognition materials. Herein we report on the state-of-the-art, the development trends, and the remaining knowledge gaps in the area of combinatorial polymeric sensor materials design.

Covalent Immobilization of Glucose Oxidase on Well-Defined Poly(glycidyl methacrylate)−Si(111) Hybrids from Surface-Initiated Atom-Transfer Radical Polymerization

A simple one-step procedure was employed for the covalent immobilization of an atom-transfer radical polymerization (ATRP) initiator, via the robust Si-C bond, on the hydrogen-terminated Si(111) surface (Si-H surface). Well-defined poly(glycidyl methacrylate) [P(GMA)] brushes, tethered directly on the (111)-oriented single-crystal silicon surface, were prepared via surface-initiated ATRP. Kinetics study on the surface-initiated ATRP of glycidyl methacrylate revealed that the chain growth from the silicon surface was consistent with a "controlled" process. A relatively high concentration of glucose oxidase (GOD; above 0.2 mg/cm2) could be coupled directly to the well-defined P(GMA) brushes via the ring-opening reaction of the epoxide groups with the amine moieties of the enzyme. The resultant GOD-functionalized P(GMA) brushes, with the accompanying hydroxyl groups from the ring-opening reaction of the epoxide groups, serves as an effective spacer to provide the GOD with a higher degree of conformational freedom and a more hydrophilic environment. An equivalent enzyme activity above 1.6 units/cm2 [micromoles of beta-D-(+)-glucose oxidized to d-gluconolactone per minute per square centimeter] and a corresponding relative activity of about 60% could be readily achieved. The immobilized GOD also exhibited an improved stability during storage over that of the free enzyme. The GOD-functionalized silicon substrates are potentially useful to the development of silicon-based glucose biosensors.

A Chitosan-Multiwall Carbon Nanotube Modified Electrode for Simultaneous Detection of Dopamine and Ascorbic Acid

A chemically modified electrode based on a chitosan-multiwall carbon nanotube (MWNT) coated glassy carbon electrode (GCE) is described, which exhibits an attractive ability to determine dopamine (DA) and ascorbic acid (AA) simultaneously. The modified electrode exhibited a high differential pulse voltammetry (DPV) current response to DA at 0.144 V and AA at -0.029 V (vs. SCE) in a 0.1 mol l(-1) phosphate buffer solution (pH = 7.2). The properties and behaviors of the chitosan-multiwall carbon nanotube modified electrode (MC/GCE) were characterized using cyclic voltammetry (CV) and DPV methods. The mechanism for the discrimination of dopamine from ascorbic acid at MC/GCE is discussed. The linear calibration range for DA and AA were 5 x 10(-7) mol l(-1) to 1 x 10(-4) mol l(-1) (r = 0.997), and 5 x 10(-6) mol l(-1) to 1 x 10(-3) mol l(-1) (r = 0.996), respectively. The MC/GCE showed good sensitivity, selectivity and stability.

Simultaneous measurement of dopamine and ascorbate at their physiological levels using voltammetric microprobe based on overoxidized poly(1,2-phenylenediamine)-coated carbon fiber

Overoxidized poly-(1,2-phenylenediamine) (OPPD)-coated carbon fiber microelectrodes (CFMEs) exhibit, in combination with square-wave voltammetry (SWV) detection mode, the attractive ability to simultaneously measure low nM dopamine (DA) and mM ascorbate (AA) in a pH 7.4 medium. The PPD polymer film is electrodeposited onto a carbon fiber at a constant potential of 0.8 V versus Ag/AgCl using a solution containing sodium dodecylsulfate as the dopant. After overoxidation using cyclic voltammetry (CV) in the potential range from 0 to 2.2 V at a scan rate of 10 V/s, the resulting OPPD-CFME displays a high SWV current response to cationic DA at approximately 0.2 V and has a favorably low response to anionic AA at approximately 0.0 V vs Ag/AgCl. The preparation of the new OPPD-sensing film has been carefully studied and optimized. The OPPD properties and behavior were characterized using CV and SWV under various conditions and are discussed with respect to DA and AA detection. The linear calibration range for DA in the presence of 0.3 mM AA is 50 nM to 10 microM, with a correlation coefficient of 0.998 and a detection limit of 10 nM using 45-s accumulation. The detection limit for DA in the absence of AA was estimated to be 2 nM (S/N = 3). The linear range for AA in the presence of 100 nM DA is 0.2-2 mM, with a correlation coefficient of 0.999 and a detection limit of 80 microM. The reproducibilities of SWV measurements at OPPD-CFCMEs are 1.6% and 2.5% for 100 nM DA and 0.3 mM AA, respectively. Potential interfering agents, such as 3,4-dihydroxyphenylacetic acid, uric acid, oxalate, human serum proteins, and glucose, at their physiologically relevant or higher concentrations did not have any effect. These favorable features offer great promise for in vitro and in vivo application of the proposed OPPD-coated microprobe.

A glucose oxidase electrode based on electropolymerized conducting polymer with polyanion-enzyme conjugated dopant

An enzyme immobilization method has been developed by electropolymerization chemistry of conducting polymer which results in a more effective and reproducible enzyme electrode. As a model system, in this study, glucose oxidase (GOD) was conjugated with a polyanion, poly(2-acrylamido-2-methylpropane sulfonic acid), via a poly(ethylene oxide) spacer to improve the efficiency of enzyme immobilization into a conducting polymer. GOD was successfully conjugated with a high conjugation yield of more than 90%, and its bioactivity was preserved. The resulting polyanion-GOD conjugate was used as a dopant for the electrochemical polymerization of pyrrole. Polypyrrole was effectively deposited on a Pt wire working electrode with the polyanion-GOD conjugate. The enzyme electrode responded to glucose concentrations of up to 20 mM with a sensitivity of 40 nA/mM at an applied potential of 0.4 V within a response time of 30 s. Although the response signal decreased at the low applied potential of 0.3 V, the enzyme electrode showed sensitive response signals of about 16 nA/mM up to 20 mM in glucose concentration. Under the deoxygenated condition, reduced but clear response current signal was obtained. The results show that the current signal response of the enzyme electrode to glucose concentration may be produced by mixed mechanisms.