Oriented Perovskite Growth Regulation Enables Sensitive Broadband Detection and Imaging of Polarized Photons Covering 300-1050 nm

Plasma-Enhanced Grain Growth and Non-Radiative Recombination Mitigation in CsSnBr3 Perovskite Films for High-Performance, Lead-Free Photodetectors

Tin-based halide perovskites represent a highly promising and eco-friendly alternative to lead-based materials with significant potential for optoelectronic applications. However, their advancement is hampered by challenges such as poor film crystallinity and unintended self-doping. Herein, this work reports the fabrication of high-quality CsSnBr3 perovskite films by plasma-assisted chemical vapor deposition (PACVD), which improves the film quality. The precise control of the ammonia plasma not only promotes grain growth and reduces grain boundaries, but also eliminates defect states in the film, mitigates oxidation of Sn2+, suppresses sub-bandgap absorption, and reduces non-radiative recombination. Consequently, the photodetectors deliver exceptional performance, including a responsivity of 11.2 A W-1, a detectivity of 2.5 × 1011 Jones, and an ultrafast response time of 1/3.3 ms. Notably, certain key metrics, including detectivity (D*) and response time, significantly surpass those of all previously reported photoconductor-type Sn-based perovskite photodetectors. The results offer not only a novel strategy for enhancing the quality and optoelectronic performance of CsSnBr3 films but also a scalable platform for the development of high-performance, lead-free perovskite materials and devices. The new knowledge opens new possibilities for the design and fabrication of sustainable materials for advanced optoelectronic applications.

Interfacial Field-Effect Enabling High-Performance Perovskite Photovoltaics

Currently, the power conversion efficiency (PCE) of inverted perovskite solar cells (PSCs) is still limited by reduced open-circuit voltage (VOC), due to defect-induced charge recombination. Most studies focus on defect passivation and improving carrier transport through introducing passivating molecules or macroscopic physical fields. Herein, to mitigate energy level mismatch and recombination losses induced by interface defects, an interface electric-field passivation is introduced, employing the ordered arrangement of the dipole molecule benzenesulfonyl chloride (BC). An enhanced VOC is achieved without the introduction of an external physical field, owing to the interfacial dipole field effect and chemical passivation by BC. Subsequently, an inverted device with a PCE of 25.41% is obtained, alongside exceptional stability, retaining 95% of the initial efficiency after 1157 h. This work demonstrates the effective dipole-induced interfacial field-effect passivation in inverted PSCs and contributes to further advancements in the efficiency and stability of inverted devices.

Removal of Residual Additive Enabling Perfect Crystallization of Photovoltaic Perovskites

Achieving high-efficiency perovskite solar cells (PSCs) hinges on the precise control of the perovskite film crystallization process, often improved by the inclusion of additives. While dimethyl sulfoxide (DMSO) is traditionally used to manage this process, its removal from the films is problematic. In this work, methyl phenyl sulfoxide (MPSO) was employed instead of DMSO to slow the crystallization rate, as MPSO is more easily removed from the perovskite structure. The electron delocalization associated with the benzene ring in MPSO decreases the electron density around the oxygen atom in the sulfoxide group, thus reducing its interaction with PbI2. This strategy not only sustains the formation of a crystallization-slowing intermediate phase but also simplifies the elimination of the additive. Consequently, the optimized PSCs achieved a leading power conversion efficiency (PCE) of 25.95 % along with exceptional stability. This strategy provides a novel method for fine-tuning perovskite crystallization to enhance the overall performance of photovoltaic devices.

Cs3Bi2Br9 nanoparticles decorated C3N4 nanotubes composite photocatalyst for highly selective oxidation of benzylic alcohol

Solar-light driven oxidation of benzylic alcohols over photocatalysts endows significant prospects in value-added organics evolution owing to its facile, inexpensive and sustainable process. However, the unsatisfactory performance of actual photocatalysts due to the inefficient charge separation, low photoredox potential and sluggish surface reaction impedes the practical application of this process. Herein, we developed an innovative Z-Scheme Cs3BiBr9 nanoparticles@porous C3N4 tubes (CBB-NP@P-tube-CN) heterojunction photocatalyst for highly selective benzyl alcohol oxidation. Such composite combining increased photo-oxidation potential, Z-Scheme charge migration route as well as the structural advantages of porous tubular C3N4 ensures the accelerated mass and ions diffusion kinetics, the fast photoinduced carriers dissociation and sufficient photoredox potentials. The CBB-NP@P-tube-CN photocatalyst demonstrates an exceptional performance for selective photo-oxidation of benzylic alcohol into benzaldehyde with 19, 14 and 3 times higher benzylic alcohols conversion rate than those of C3N4 nanotubes, Cs3Bi2Br9 and Cs3Bi2Br9@bulk C3N4 photocatalysts, respectively. This work offers a sustainable photocatalytic system based on lead-free halide perovskite toward large scale solar-light driven value-added chemicals production.

Filter-Less Color-Selective Photodetector Derived from Integration of Parallel Perovskite Photoelectric Response Units

Color-selective photodetectors (PDs) play an indispensable role in spectral recognition, image sensing, and other fields. Nevertheless, complex filters and delicate optical paths in such devices significantly increase their complexity and size, which subsequently impede their integration in smart optoelectronic chips for universal applications. This work demonstrates the successful fabrication of filter-less color-selective perovskite PDs by integrating three perovskite units with different photoresponse on a single chip. The variation in photoresponse is attributed to different quantities of SnO2 nanoparticles, synthesized through controlled ultrasonic treatment on the surface of the electron transportation layer SnS2, which selectively absorb short-wavelength light, thus increasing the relative transmittance of long-wavelength light and enhancing the photoresponse of the units to long wavelengths. By integrating any two units and deriving the formula for the wavelength to the responsivity ratio, a wavelength sensor is developed which can accurately identify incident light in the range of 400-700 nm with a minimum error <3 nm. Furthermore, the device integrating three units with different photoresponse can identify red, green and blue in polychromatic light to achieve color imaging with a relative error <6%. This work provides valuable insights into wavelength identification and color imaging of perovskite PDs.

Highly-efficient low-cost polarization-sensitive organic photodetectors based on laminated self-assembly planar and bulk heterojunctions

To overcome the severe problems arising from the insufficient light absorption of ultrathin self-assembly active layers and the high cost use of atomic force deposition (ALD)-grown low-leakage-current transport layers, we successfully developed a low-cost, simple and facile strategy of floating-film transfer and multilayer lamination (FFTML) for constructing highly-efficient ALD-free broadband polarization-sensitive organic photodetectors (OPDs) with the two commonly used structures of donor/acceptor planar heterojunction (PHJ) and donor:acceptor multilayer bulk heterojunction (BHJ). It was found that the PHJ-based polarization-sensitive OPD by FFTML possesses a low dark current due to the high carrier injection barrier, indicating it is more suitable to be applied in low polarized light detection scenarios. In contrast, the BHJ-based device by FFTML has a higher spectral responsivity in the whole wavelength due to more photo-excitons transferred to the donor:acceptor interface and dissociated into photoexcited carrirers. Furthermore, the film thickness, which is tuned by increasing lamination number of BHJ layers, has a big effect on the polarization-sensitive photodetection performance. The polarization-sensitive 4-BHJ OPD by FFTML finally achieved a high specific detectivity of 8.33 × 1010Jones, which was much higher than 2.72 × 1010Jones for the 2-BHJ device at 0 V. This work demonstrates that layer-by-layer lamination of self-assembly films can effectively improve the polarized-light detection performance, contributing significantly to the rapid development of the field.

Uniaxial-Oriented Chiral Perovskite for Flexible Full-Stokes Polarimeter

Full-Stokes polarization detection, with high integration and portability, offers an efficient path toward next-gen multi-information optoelectronic systems. Nevertheless, current techniques relying on optical filters create rigid and bulky configurations, limiting practicality. Here, a flexible, filter-less full-Stokes polarimeter featuring a uniaxial-oriented chiral perovskite film is first reported. It is found that, the strategic manipulation of the surfactant-mediated Marangoni effect during blade coating, is crucial for guiding an equilibrious mass transport to achieve oriented crystallization. Through this approach, the obtained uniaxial-oriented chiral perovskite films inherently possess anisotropy and chirality, and thereby with desired sensitivity to both linearly polarized light and circularly polarized light vectors. The uniaxial-oriented crystalline structure also improves photodetection, achieving a specific detectivity of 5.23 × 1013 Jones, surpassing non-oriented devices by 10×. The as-fabricated flexible polarimeters enable accurate capture of full-Stokes polarization without optical filters, exhibiting slight detection errors for the Stokes parameters: ΔS1 = 9.2%, ΔS2 = 8.6%, and ΔS3 = 6.5%, approaching the detection accuracy of optics-filter polarimeters. This proof of concept also demonstrates applications in matrix polarization imaging.

Realization of High-Performance Self-Powered Polarized Photodetection with Large Temperature Window in a 2D Polar Perovskite

Polarization photodetection taking advantage of the anisotropy of 2D materials shines brilliantly in optoelectronic fields owing to differentiating optical information. However, the previously reported polarization detections are mostly dependent on external power sources, which is not conducive to device integration and energy conservation. Herein, a 2D polar perovskite (CBA)2CsPb2Br7 (CCPB, CBA = 4-chlorobenzyllamine) has been successfully synthesized, which shows anticipated bulk photovoltaic effect (BPVE) with an open-circuited photovoltage up to ≈0.2 V. Devices based on CCPB monomorph fulfill a fascinating self-powered polarized photodetection with a large polarization ratio of 2.7 at room temperature. Moreover, CCPB features a high phase-transition temperature (≈475 K) which prompts such self-powered polarized photodetection in a large temperature window of device operation, since BPVE generated by spontaneous polarization can only exist in the polar structure prior to the phase transition. Further computational investigation reveals the introduction of CBA+ with a large dipole moment contributes to quite large polarization (17.5 µC cm-2) and further super high phase transition temperature of CCPB. This study will promote the application of 2D perovskite materials for self-powered polarized photodetection in high-temperature conditions.

Dimension-Confined Growth of a Crack-Free PbS Microplate Array for Infrared Image Sensing

Epitaxy of semiconductors is a necessary step toward the development of electronic devices such as lasers, detectors, transistors, and solar cells. However, the lattice ordering of semiconductor functional films is inevitably disrupted by excessive concentrated stress due to the mismatch of the thermal expansion coefficient. Herein, combined with the first-principles calculation, we find that a rigid film/substrate bilayer heterostructure with a large thermal expansion mismatch upon cooling to room temperature from growth is free of surface cracks when the rigid film exhibits a dimension smaller than the critical condition for the breaking energy. The principle has been verified in a PbS/SrTiO3 bilayer system that is crack free on PbS single-crystalline microplate arrays through the designing of a dimension-confined growth (DCG) method. Interestingly, this crack-free, large-scale PbS microplate array exhibits exceptional uniformity in morphology, dimensions, thickness, and photodetection properties, enabling a broad-band infrared image sensing. This work provides a new perspective to design materials and arrays that demand smooth and continuous surfaces, which are not limited only to semiconductor electronics but also include mechanical structures, optical materials, biomedical materials, and others.

Molecularly Thin 2D Organic Single Crystals: A New Platform for High-Performance Polarization-Sensitive Phototransistors

The inherent linear dichroism (LD), high absorption, and solution processability of organic semiconductors hold immense potential to revolutionize polarized light detection. However, the disordered molecular packing inherent to polycrystalline thin films obscures their intrinsic diattenuation, resulting in diminished polarization sensitivity. In this study, we develop filter-free organic polarization-sensitive phototransistors (PSPs) with both a high linear dichroic ratio (LDR) and exceptional photosensitivity utilizing molecularly thin dithieno[3,2-b:2',3'-d]thiophene derivatives (DTT-8) two-dimensional molecular crystals (2DMCs) as the active layer. The orderly molecular packing in 2DMCs amplifies the inherent LD, and their molecular-scale thickness enables complete channel depletion, significantly reducing the dark current. As a result, PSPs with an impressive LDR of 3.15 and a photosensitivity reaching 3.02 × 106 are obtained. These findings present a practical demonstration of using the polarization angle as an encryption key in optical communication, showcasing the potential of 2DMCs as a viable and promising category of semiconductors for filter-free, polarization-sensitive photodetectors.

A Polarization-Sensitive Photodetector with Patterned CH3NH3PbCl3 Film

Perovskite photodetectors with polarization-sensitive properties have gained significant attention due to their potential applications in fields such as imaging and remote sensing. Most perovskite photodetectors concentrate on iodine (I) or bromine (Br)-based materials, primarily due to their straightforward fabrication techniques. The utilization of chloride (Cl)-based perovskites with wider bandgaps, such as CH3NH3PbCl3, is relatively limited. In this work, polarized perovskite photodetectors are prepared by a patterned spatially confined method with polarization sensitivity and excellent optoelectronic properties. The patterned perovskite photodetectors (PP-PDs) not only exhibit outstanding photoelectric conversion performance but also demonstrate polarization sensitivity. PP-PDs showcase remarkable performance, including on/off ratios of 3.4 × 104, an extremely low dark current of 1.56 × 10-11 A, and a rapid response time of microseconds. The responsivity and detectivity of PP-PDs reach 10.6 A W-1 and 3 × 1012 Jones, respectively, positioning them as among the highest-performing MAPbCl3-based photodetectors reported to date. Furthermore, polarization layered imaging sensing is achieved using stepwise scanning of the device. This work provides innovative ideas for realizing high-performance polarized perovskite photodetectors.

Magnetic-biased chiral molecules enabling highly oriented photovoltaic perovskites

The interaction between sites A, B and X with passivation molecules is restricted when the conventional passivation strategy is applied in perovskite (ABX3) photovoltaics. Fortunately, the revolving A-site presents an opportunity to strengthen this interaction by utilizing an external field. Herein, we propose a novel approach to achieving an ordered magnetic dipole moment, which is regulated by a magnetic field via the coupling effect between the chiral passivation molecule and the A-site (formamidine ion) in perovskites. This strategy can increase the molecular interaction energy by approximately four times and ensure a well-ordered molecular arrangement. The quality of the deposited perovskite film is significantly optimized with inhibited nonradiative recombination. It manages to reduce the open-circuit voltage loss of photovoltaic devices to 360 mV and increase the power conversion efficiency to 25.22%. This finding provides a new insight into the exploration of A-sites in perovskites and offers a novel route to improving the device performance of perovskite photovoltaics.

2D Ruddlesden-Popper Sn-Based Perovskite Weak Light Detector for Image Transmission and Reflection Imaging

2D Ruddlesden-Popper Sn-based perovskite has excellent optoelectronic properties and weak halide ion migration characteristics, making it an ideal candidate for weak light detection, which has great potential in light communication, and medical applications. Although Sn-based perovskite photodetectors are developed, weak light detection is not demonstrated yet. Herein, a high-performance self-powered photodetector with the capability to detect ultra-weak light signals is designed based on vertical PEA2 SnI4 /Si nanowires heterojunction. Due to the low dark current and high light absorption efficiency, the devices present a remarkable responsivity of 42.4 mA W-1 , a high detectivity of 8 × 1011 Jones, and an ultralow noise current of 2.47 × 10-13 A Hz-1/2 . Especially, the device exhibits a high on-off current ratio of 18.6 at light signals as low as 4.60 nW cm-2 , revealing the capacity to detect ultra-weak light. The device is applied as a signal receiver and realized image transmission in light communication system. Moreover, high-resolution reflection imaging and multispectral imaging are obtained using the device as the sensor in the imaging system. These results reveal that 2D PEA2 SnI4 -based self-powered photodetectors with low-noise current possess enormous potential in future weak light detection.

Density-discriminating chromatic x-ray imaging based on metal halide nanocrystal scintillators

X-ray imaging based on a single gray level shows visual blind parts and affects accurate judgment in some situations. Color-cognized x-ray imaging will boost the recognition capability, which has not yet been reported. Here, we propose a quartz-assisted chromatic x-ray imaging model based on metal halide nanocrystal (NC) stacked scintillators. Mutually inactive (BA)2PbBr4:Mn and Cs3Cu2I5:Tl enable x-ray energy- or density-dependent radioluminescence (RL) color variation. The upper scintillator light yield and the bottom scintillator transmittance are enhanced by elaborate in situ passivation of phenethylamine bromide and NC orientation regulation, respectively. Imaging targets with different densities are distinguished on RL spectra, and the color coordinates shift linearly on CIE 1931. An algorithm balances the image details of different gray areas and enhances the visual perception by color filling. This work provides color recognition between objects with different densities and takes a step toward chromatic x-ray imaging applied to practical scenarios.

Multifunctional Perovskite Photodetectors: From Molecular-Scale Crystal Structure Design to Micro/Nano-scale Morphology Manipulation

Multifunctional photodetectors boost the development of traditional optical communication technology and emerging artificial intelligence fields, such as robotics and autonomous driving. However, the current implementation of multifunctional detectors is based on the physical combination of optical lenses, gratings, and multiple photodetectors, the large size and its complex structure hinder the miniaturization, lightweight, and integration of devices. In contrast, perovskite materials have achieved remarkable progress in the field of multifunctional photodetectors due to their diverse crystal structures, simple morphology manipulation, and excellent optoelectronic properties. In this review, we first overview the crystal structures and morphology manipulation techniques of perovskite materials and then summarize the working mechanism and performance parameters of multifunctional photodetectors. Furthermore, the fabrication strategies of multifunctional perovskite photodetectors and their advancements are highlighted, including polarized light detection, spectral detection, angle-sensing detection, and self-powered detection. Finally, the existing problems of multifunctional detectors and the perspectives of their future development are presented.

Dual Emission Bands of a 2D Perovskite Single Crystal with Charge Transfer State Characteristics

Several hybrid halide 2D-perovskite species emit light with an emergent and controversial broadband emission Stokes-shifted down from the narrow band emission. This paper uncovers the sub- and above-bandgap emission and absorption characteristics of PEA₂PbI₄ prepared with gap states introduced during single crystal growth. Here, gap states led to coexistent intrinsic and heterostructured electronic frameworks that are selectively accessible with ultraviolet (UV) and infrared (IR) light, respectively, resulting in the phenomenon of photoluminescence (PL) switching from narrowband green to broadband red. Electron-energy dependent cathodoluminescence shows a relative increase in the broadband red PL intensity as the electron penetration depth increases from 30 nm to 2 μm, confirming the heterostructured framework is formed in the bulk of the crystal. Excitation-emission power slope of 2.5 and up-conversion pump transient absorption (TA) spectra suggest that the IR up-conversion excitation with red photoluminescence, peaked at 655 nm, is a multiphoton process occurring in the heterostructured framework through a nonlinear optical response. The energetic pathways toward the dual emission bands are revealed by pump-probe transient absorption spectroscopy, showing energetically broad gap states with high sensitivity to an IR pump are upconverted and subsequently quickly relax from high to low energy levels within 4 ps. Furthermore, the up-conversion red PL demonstrates a linear polarization with magnetic field effects, thus affirming that the band-like heterostructured framework is crystallographically aligned with characteristics of spatially extended charge-transfer states.

High-Speed Printing of Narrow-Band-Gap Sn-Pb Perovskite Layers toward Cost-Effective Manufacturing of Optoelectronic Devices

Narrow-band-gap Sn-Pb perovskites have emerged as one of the most promising solution-processed near-infrared (NIR) light-detection technologies, with the key figure-of-merit parameters already rivaling those of commercial inorganic devices, but maximizing the cost advantage of solution-processed optoelectronic devices depends on the ability to fast-speed production. However, weak surface wettability to perovskite inks and evaporation-induced dewetting dynamics have limited the solution printing of uniform and compact perovskite films at a high speed. Here, we report a universal and effective methodology for fast printing of high-quality Sn-Pb mixed perovskite films at an unprecedented speed of 90 m h^-1 by altering the wetting and dewetting dynamics of perovskite inks with the underlying substrate. A line-structured SU-8 pattern surface to trigger spontaneous ink spreading and fight ink shrinkage is designed to achieve complete wetting with a near-zero contact angle and a uniform dragged-out liquid film. The high-speed printed Sn-Pb perovskite films have both large perovskite grains (>100 μm) and excellent optoelectronic properties, yielding highly efficient self-driven NIR photodetectors with a large voltage responsivity over 4 orders of magnitude. Finally, the potential application of the self-driven NIR photodetector in health monitoring is demonstrated. The fast printing methodology provides a new possibility to extend the manufacturing of perovskite optoelectronic devices to industrial production lines.

Compositional gradient engineering and applications in halide perovskites

Organic-inorganic halide perovskites (HPs) have attracted respectable interests as active layers in solar cells, light-emitting diodes, photodetectors, etc. Besides the promising optoelectronic properties and solution-processed preparation, the soft lattice in HPs leads to flexible and versatile compositions and structures, providing an effective platform to regulate the bandgaps and optoelectronic properties. However, conventional solution-processed HPs are homogeneous in composition. Therefore, it often requires the cooperation of multiple devices in order to achieve multi-band detection or emission, which increases the complexity of the detection/emission system. In light of this, the construction of a multi-component compositional gradient in a single active layer has promising prospects. In this review, we summarize the gradient engineering methods for different forms of HPs. The advantages and limitations of these methods are compared. Moreover, the entropy-driven ion diffusion favors compositional homogeneity, thus the stability issue of the gradient is also discussed for long-term applications. Furthermore, applications based on these compositional gradient HPs will also be presented, where the gradient bandgap introduced therein can facilitate carrier extraction, and the multi-components on one device facilitate functional integration. It is expected that this review can provide guidance for the further development of gradient HPs and their applications.

Linearly Polarization-Sensitive Perovskite Photodetectors

Polarization is an exceptional physical property of light that carries and differentiates a significant amount of optical information. Perovskite materials are utilized in polarization-sensitive photodetectors owing to their crystal structure anisotropy and controllable orientation growth, in addition to their excellent photovoltaic performance. This paper presents an overview of the structural characteristics and photovoltaic performance of different optical structures and low-dimensional perovskite polarization photodetectors. This summary will contribute to the future development of perovskite-based photodetectors that are sensitive to polarization.

Narrow-bandgap Sn-Pb mixed perovskite single crystals for high-performance near-infrared photodetectors

Narrow-bandgap Sn-Pb mixed perovskite single crystals are highly promising as photoactive materials for efficient and low-cost near-infrared (NIR) photodetectors. However, because of the significant difference in the crystallization velocities for Pb- and Sn-based perovskites, Sn-Pb mixed perovskites are peculiarly prone to phase separation during the crystallization process, causing the degradation of the optical and electronic properties of materials. Herein, we propose a low-temperature space-confined technique (LT-SCT) that simultaneously reduces the crystallization velocities of pure Sn and Pb perovskites, enabling the fabrication of pure-phase (FASnI₃)_0.1(MAPbI₃)_0.9 single crystals. The resulting (FASnI₃)_0.1(MAPbI₃)_0.9 single crystals exhibit excellent crystallinity with a high hole mobility of 7.44 × 10³ cm² V^-1 s^-1 and a low surface trap density of 1.88 × 10⁹ cm^-2. These properties benefit the application of (FASnI₃)_0.1(MAPbI₃)_0.9 single crystals in self-powered NIR photodetectors and yield outstanding comprehensive performance, especially with a broad linear dynamic range of up to 163.5 dB, a large responsivity (R) of 0.53 A W^-1, and a fast response speed of 22.78 μs in the NIR spectral region (750-860 nm). Furthermore, high-quality NIR imaging and wearable health monitoring are achieved by employing high-performance and self-driven NIR photodetectors. This work contributes to developing Sn-Pb mixed perovskite single crystals and provides a promising candidate for efficient and low-cost NIR photodetection.

Near-infrared polarization-sensitive photodetection via interfacial symmetry engineering of an Si/MAPbI3 heterostructural single crystal

Methylammonium lead iodide (MAPbI₃) single crystals (SCs) have drawn particular attention in the optoelectronics field, due to their outstanding photoelectric performance. However, the structures of those MAPbI₃ SCs are isotropic, which limits the further application of the materials for polarization-sensitive photodetection. Here, we propose a strategy of symmetry modulation by heterogeneously integrating large-sized MAPbI₃ SCs with silicon (Si) wafers and we give the first demonstration of self-powered near-infrared (NIR) polarization-sensitive photodetection using MAPbI₃ SCs. Created via a delicate solution method, the MAPbI₃/Si heterostructures show a high crystalline quality and a solid interfacial connection. More importantly, the built-in electric field resulting from the band bending at the MAPbI₃/Si heterostructure interface generates polar symmetry, which enables directional transport of photogenerated carriers, making the MAPbI₃/Si heterostructures highly polarization-sensitive. Consequently, in the self-powered mode, NIR photodetectors of MAPbI₃/Si heterostructures exhibit large polarization ratios of 3.3 at 785 nm and 2.8 at 940 nm. Moreover, a high detectivity of 7.35 × 10¹² Jones of the present devices is also achieved. Our work gives the first demonstration of self-powered polarization-sensitive photodetection of MAPbI₃ SCs and provides a strategy to design polarization-sensitive materials beyond the conventional limitations induced by isotropic structures.

Strong Anisotropic Two-Dimensional In2Se3 for Light Intensity and Polarization Dual-Mode High-Performance Detection

Detecting the light from different freedom is of great significance to gain more information. Two-dimensional (2D) materials with low intrinsic carrier concentration and highly tunable electronic structure have been considered as the promising candidate for future room-temperature multi-functional photodetectors. However, current investigations mainly focus on intensity-sensitive detection; the multi-dimensional photodetection such as polarization-sensitive photodetection is still in its early stage. Herein, the intensity- and polarization-sensitive photodetection based on α-In₂Se₃ is studied. By using angle-resolved polarized Raman spectroscopy, it is demonstrated that α-In₂Se₃ shows an anisotropic phonon vibration property indicating its asymmetric structure. The α-In₂Se₃-based photodetector has a photoelectric performance with a responsivity of 1936 A/W and a specific detectivity of 2.1 × 10¹³ Jones under 0.2 mW/cm² power density at 400 nm. Moreover, by studying the polarized angle-resolved photoelectrical effect, it is found that the ratio of maximum and minimum photocurrent (dichroic ratio) reaches 1.47 at 650 nm suggesting good polarization-sensitive detection. After post-annealing, α-In₂Se₃ in situ converts to β-In₂Se₃ which has similar in-plane anisotropic crystallinity and exhibits a dichroic ratio of 1.41. It is found that the responsivity of β-In₂Se₃ is 6 A/W, much lower than that of α-In₂Se₃. The high-performance light intensity- and polarization-detection of α-In₂Se₃ enlarges the 2D anisotropic materials family and provides new opportunities for future dual-mode photodetection.

Highly Sensitive Broadband Phototransistors Based on Gradient Tin/Lead Mixed Perovskites

Highly sensitive broadband photodetectors are critical to numerous cutting-edge technologies such as biomedical imaging, environment monitoring, and night vision. Here, phototransistors based on mixed Sn/Pb perovskites are reported, which demonstrate ultrahigh responsivity, gain and specific detectivity in a broadband from ultraviolet to near-infrared region. The interface properties of the perovskite phototransistors are optimized by a special three-step cleaning-healing-cleaning treatment, leading to a high hole mobility in the channel. The highly sensitive performance of the mixed Sn/Pb perovskite phototransistors can be attributed to the vertical compositional heterojunction automatically formed during the film deposition, which is helpful for the separation of photocarriers thereby enhancing a photogating effect in the perovskite channel. This work demonstrates a convenient approach to achieving high-performance phototransistors through tuning compositional gradient in mixed-metal perovskite channels.

Phase-Transition-Cycle-Induced Recrystallization of FAPbI3 Film in An Open Environment Toward Excellent Photodetectors with High Reproducibility

Perovskite is an attractive building block for future optoelectronic applications. However, the strict fabrication conditions of perovskite devices impede the transformation of lab techniques into commercial applications. Here, a facile annealing-free posttreatment is proposed to reconstruct the perovskite film to obtain high-performance photodetectors with an optimized production rate. With posttreatment by methylamine thiocyanate, the prefabricated formamidinium-lead triiodide (FAPbI₃ ) film will undergo a recrystallization process consisting of a repeating phase-transition-cycle (PTC) between the black and yellow phases of FAPbI₃ , which improves the crystal quality and eliminates defects. As a result, some casually prepared or even decomposed perovskite films can be reconstructed, and the dispersion degree of the device performance based on the posttreatment method decreases by ≈21% compared to the traditional antisolvent method. This facile and annealing-free posttreatment will be an attractive method for the future industrial production of perovskite devices.

Anisotropic charge trapping in phototransistors unlocks ultrasensitive polarimetry for bionic navigation

Being able to probe the polarization states of light is crucial for applications from medical diagnostics and intelligent recognition to information encryption and bio-inspired navigation. Current state-of-the-art polarimeters based on anisotropic semiconductors enable direct linear dichroism photodetection without the need for bulky and complex external optics. However, their polarization sensitivity is restricted by the inherent optical anisotropy, leading to low dichroic ratios of typically smaller than ten. Here, we unveil an effective and general strategy to achieve more than 2,000-fold enhanced polarization sensitivity by exploiting an anisotropic charge trapping effect in organic phototransistors. The polarization-dependent trapping of photogenerated charge carriers provides an anisotropic photo-induced gate bias for current amplification, which has resulted in a record-high dichroic ratio of >10⁴, reaching over the extinction ratios of commercial polarizers. These findings further enable the demonstration of an on-chip polarizer-free bionic celestial compass for skylight-based polarization navigation. Our results offer a fundamental design principle and an effective route for the development of next-generation highly polarization-sensitive optoelectronics.

Aligned Plasmonic Antenna and Upconversion Nanoparticles toward Polarization-Sensitive Narrowband Photodetection and Imaging at 1550 nm

Lanthanide-doped upconversion nanoparticles (UCNPs) are rising as prospect nanomaterials for constructing polarization-sensitive narrowband near-infrared (NIR) photodetectors (PDs), which have attracted significant interest in astronomy, object identification, and remote sensing. However, polarized narrowband NIR photodetection and imaging based on UCNPs have yet to be realized. Herein, we demonstrate that NIR photodetection and imaging are capable of sensing polarized light as well as affording wavelength-selective detection at 1550 nm by integrating directional-Au@Ag nanorods (D-Au@Ag NRs) with NaYF4:Er3+@NaYF4 UCNPs. Monolayer and large-area D-Au@Ag NRs polarization-sensitive plasmonic antenna films are obtained, and the center of their localized surface plasmon resonance (LSPR) peak is located at around 1550 nm. Experimental and theoretical results reveal that D-Au@Ag NRs have a sharp localized LSPR peak with a dominant scattering cross section. The UCNPs coupled with D-Au@Ag NRs exhibit significantly enhanced and strongly polarization-dependent luminescence with a high degree of polarization (DOP) of 0.72. The first polarization-resolved UC narrowband PD at 1550 nm is achieved, which delivers a DOP of 0.63, a detectivity of 1.69 × 1010 Jones, and a responsivity of 0.32 A/W. Finally, we develop a polarized imaging system for 1550 nm with visual photoelectric detection based on the aforementioned PDs. Our work opens up possibilities for manipulating UC and developing next-generation polarization-sensitive narrowband infrared photodetection and imaging technology.

Perovskite Wide-Angle Field-Of-View Camera

Researchers have attempted to create wide-angle field-of-view (FOV) cameras inspired by the structure of the eyes of animals, including fisheye and compound eye cameras. However, realizing wide-angle FOV cameras simultaneously exhibiting low distortion and high spatial resolution remains a significant challenge. In this study, a novel wide-angle FOV camera is developed by combining a single large-area flexible perovskite photodetector (FP-PD) using computational technology. With this camera, the proposed single-photodetector imaging technique can obtain high-spatial-resolution images using only a single detector, and the large-area FP-PD can be bent further to collect light from a wide-angle FOV. The proposed camera demonstrates remarkable features of an extraordinarily tunable wide FOV (greater than 150°), high spatial resolution of 256 × 256 pixels, and low distortion. It is believed that the proposed compatible and extensible camera prototype will promote the development of high-performance versatile FOV cameras.

Multidimensional Perovskites for High Detectivity Photodiodes

Low-dimensional perovskites attract increasing interest due to tunable optoelectronic properties and high stability. Here, it is shown that perovskite thin films with a vertical gradient in dimensionality result in graded electronic bandgap structures that are ideal for photodiode applications. Positioning low-dimensional, vertically-oriented perovskite phases at the interface with the electron blocking layer increases the activation energy for thermal charge generation and thereby effectively lowers the dark current density to a record-low value of 5 × 10^-9  mA cm^-2 without compromising responsivity, resulting in a noise-current-based specific detectivity exceeding 7 × 10¹² Jones at 600 nm. These multidimensional perovskite photodiodes show promising air stability and a dynamic range over ten orders of magnitude, and thus represent a new generation of high-performance low-cost photodiodes.

Strong Polarized Photoluminescence CsPbBr3 Nanowire Composite Films for UV Spectral Conversion Polarization Photodetector Enhancement

In this work, we proposed a fluorescence conversion layer with polarization characteristics to enhance UV polarization detection for the first time. To achieve this goal, the colloidal lead halide CsPbBr₃ nanowires (NWs) with appropriate lengths were synthesized by the method of ultrasonication synthesis assisted by the addition of hydrobromic acid (HBr) ligands. By adding HBr, the properties of synthesized NWs are improved, and due to the controllable perovskite-stretched NWs, polymer composite films were fabricated, which can generate photoluminescence (PL) with strong polarization. The optimized stretched composite film can achieve a polarization degree of 0.42 and dichroism ratio (I_∥/I_⊥) of 2.49 at 520 nm. Based on this film, an imaging system with polarization-selective properties and efficient UV spectral conversion was developed. The spectrum conversion of 266 to 520 nm luminescence wavelength was realized and sensitive to the polarization of incoming 266 nm UV light. The experimental results also showed that the response after spectral conversion is greatly improved, and different responsivities can correspond to different polarization states. This imaging system overcomes the insufficiency of the conventional charge coupled device (CCD), which makes it difficult to receive the optical signal for high-quality UV imaging. The use of light conversion films with polarization characteristics for polarized UV imaging is of great significance for improving the detection of solar-blind UV bands and the recognition of military targets.