Polymer Solar Cells with Active Layer Thickness Compatible with Scalable Fabrication Processes: A Meta-Analysis

Organic indoor PV: vanishing surface recombination allows for robust device architecture

As a promising candidate to drive low-power, off-grid applications, organic indoor photovoltaics are beginning to attract research and commercial attention. In organic photovoltaic devices, charge transport layers are often used to promote the extraction of majority carriers, while blocking minority carriers. They can however be a source of device degradation and introduce additional complexity to the fabrication of the device stack. Here, a simplified, yet performant indoor OPV architecture is demonstrated with extended absorber thickness and without electron transport layer (ETL). We show that the diminished impact of the ETL on indoor OPV results from a drastically reduced surface recombination in thick absorber devices. However, the ETL remains important under strong, outdoor illumination, since in that case the reduced surface recombination is overwhelmed by bulk recombination. The proposed simplified device architecture with thick absorber (>500 nm) has great potential in large-scale production of indoor OPV.

Low-loss contacts on textured substrates for inverted perovskite solar cells

Inverted perovskite solar cells (PSCs) promise enhanced operating stability compared to their normal-structure counterparts1-3. To improve efficiency further, it is crucial to combine effective light management with low interfacial losses4,5. Here we develop a conformal self-assembled monolayer (SAM) as the hole-selective contact on light-managing textured substrates. Molecular dynamics simulations indicate that cluster formation during phosphonic acid adsorption leads to incomplete SAM coverage. We devise a co-adsorbent strategy that disassembles high-order clusters, thus homogenizing the distribution of phosphonic acid molecules, and thereby minimizing interfacial recombination and improving electronic structures. We report a laboratory-measured power conversion efficiency (PCE) of 25.3% and a certified quasi-steady-state PCE of 24.8% for inverted PSCs, with a photocurrent approaching 95% of the Shockley-Queisser maximum. An encapsulated device having a PCE of 24.6% at room temperature retains 95% of its peak performance when stressed at 65 °C and 50% relative humidity following more than 1,000 h of maximum power point tracking under 1 sun illumination. This represents one of the most stable PSCs subjected to accelerated ageing: achieved with a PCE surpassing 24%. The engineering of phosphonic acid adsorption on textured substrates offers a promising avenue for efficient and stable PSCs. It is also anticipated to benefit other optoelectronic devices that require light management.

Nonfused Ring Electron Acceptors for Ternary Polymer Solar Cells with Low Energy Loss and Efficiency Over 18

Ternary polymer solar cells(PSCs) have been identified as an effective approach to improving power conversion efficiency (PCE) of binary PSCs. However, most of the third component, especially Y-series non-fullerene acceptors, is a fused ring acceptor which often requires a rather tedious synthesis and the use of hazardous organostannane reagents. In this work, two nonfused ring acceptors IOEH-4F and IOEH-N2F are synthesized by a green synthetic route and incorporated into PM6:Y6 blend. Encouragingly, the IOEH-4F and IOEH-N2F-based ternary PSCs exhibited more efficient charge transfer, exciton separation, and lower energy loss than PM6:Y6-based PSCs. And the IOEH-4F and IOEH-N2F-based ternary PSCs achieved an impressive PCE of 17.80% and 18.13%, respectively, which are higher than that of PM6:Y6 based PSCs (16.18%). Notably, these PCE values are also the highest PCEs for ternary PSCs including non-fused ring acceptors. Importantly, even when the IOEH-N2F:Y6 ratios increased from 0.05:1.2 to 0.50:1.2, the PCE of IOEH-N2F-based ternary PSCs (16.70%) are still higher than that of PM6:Y6 based PSCs, indicating the great potential for cost saving. It is believed that the findings will help the design of better nonfused ring acceptors and the optimization of corresponding ternary PSCs with cost-saving advantage.

Transparent Recombination Electrode with Dual-Functional Transport and Protective Layer for Efficient and Stable Monolithic Perovskite/Organic Tandem Solar Cells

Rational selection and design of recombination electrodes (RCEs) are crucial to enhancing the power conversion efficiency (PCE) and stability of monolithic tandem solar cells (TSCs). Sputtered indium tin oxide (ITO) with high conductivity and excellent transmittance is introduced as RCE in perovskite/organic TSCs. To prevent high-energy ITO particles destroy the underlying material during sputtering, dual-functional transport and protective layer (C1) is employed. The styryl group in C1 can be thermally crosslinked to serve as a sputtering protective layer. Meanwhile, the conjugated phenanthroline skeleton in C1 shows high electron mobility and hole blocking capability to promote the electron transport process at the interfaces and effectively reduce charge accumulation. Monolithic perovskite/organic TSC with high PCE of 24.07% and excellent stability is demonstrated by stacking a 1.77 eV bandgap perovskite layer and a 1.35 eV bandgap organic active layer. This strategy provides new insights for overcoming the fundamental efficiency limits of single-junction devices and promotes the further development of TSC devices.

Silicon- and Germanium-Functionalized Perylene Diimides: Synthesis, Optoelectronic Properties, and Their Application as Non-fullerene Acceptors in Organic Solar Cells

Organic solar cells have been continuously studied and developed through the last decades. A major step in their development was the introduction of fused-ring non-fullerene electron acceptors. Yet, beside their high efficiency, they suffer from complex synthesis and stability issues. Perylene-based non-fullerene acceptors, in contrast, can be prepared in only a few steps and display good photochemical and thermal stability. Herein, we introduce four monomeric perylene diimide acceptors obtained in a three-step synthesis. In these molecules, the semimetals silicon and germanium were added in the bay position, on one or both sides of the molecules, resulting in asymmetric and symmetric compounds with a red-shifted absorption compared to unsubstituted perylene diimide. Introducing two germanium atoms improved the crystallinity and charge carrier mobility in the blend with the conjugated polymer PM6. In addition, charge carrier separation is significantly influenced by the high crystallinity of this blend, as shown by transient absorption spectroscopy. As a result, the solar cells reached a power conversion efficiency of 5.38 %, which is one of the highest efficiencies of monomeric perylene diimide-based solar cells recorded to date.

Assembly of galvinoxyl doped in polymer-fullerene photovoltaic blends

Galvinoxyl (Gx) is a stable free radical used as a dopant in active layers of organic solar cells. Here, the nanoscale arrangement of Gx molecules in a composite of the PCDTBT polymer and modified C60 fullerene, PCBM, was studied using a two-pulse electron spin echo (ESE) technique. The results show that the Gx molecules assemble into clusters, which can be described by the model of 8 molecules on the surface of a sphere with a radius of 2.0 nm. Such a structure can arise due to the octahedral packing of 6 PCBM molecules surrounded by 8 Gx molecules. ESE decays also indicate that these clusters repel each other, forming a quasi-regular nanostructure in the matrix. The Gx concentration of 2 wt% at which clusters appear correlates with the literature data on the Gx-induced enhancement of photocurrent, which provides structural insight into the possible molecular mechanism of this enhancement.

Machine learning of atomic force microscopy images of organic solar cells

The bulk heterojunction structures of organic photovoltaics (OPVs) have been overlooked in their machine learning (ML) approach despite their presumably significant impact on power conversion efficiency (PCE). In this study, we examined the use of atomic force microscopy (AFM) images to construct an ML model for predicting the PCE of polymer : non-fullerene molecular acceptor OPVs. We manually collected experimentally observed AFM images from the literature, applied data curing and performed image analyses (fast Fourier transform, FFT; gray-level co-occurrence matrix, GLCM; histogram analysis, HA) and ML linear regression. The accuracy of the model did not considerably improve even by including AFM data in addition to the chemical structure fingerprints, material properties and process parameters. However, we found that a specific spatial wavelength of FFT (40-65 nm) significantly affects PCE. The GLCM and HA methods, such as homogeneity, correlation and skewness expand the scope of image analysis and artificial intelligence in materials science research fields.

Advances in organic photovoltaic cells: a comprehensive review of materials, technologies, and performance

This paper provides a comprehensive overview of organic photovoltaic (OPV) cells, including their materials, technologies, and performance. In this context, the historical evolution of PV cell technology is explored, and the classification of PV production technologies is presented, along with a comparative analysis of first, second, and third-generation solar cells. A classification and comparison of PV cells based on materials used is also provided. The working principles and device structures of OPV cells are examined, and a brief comparison between device structures is made, highlighting their advantages, disadvantages, and key features. The various parts of OPV cells are discussed, and their performance, efficiency, and electrical characteristics are reviewed. A detailed SWOT analysis is conducted, identifying promising strengths and opportunities, as well as challenges and threats to the technology. The paper indicates that OPV cells have the potential to revolutionize the solar energy industry due to their low production costs, and ability to produce thin, flexible solar cells. However, challenges such as lower efficiency, durability, and technological limitations still exist. Despite these challenges, the tunability and versatility of organic materials offer promise for future success. The paper concludes by suggesting that future research should focus on addressing the identified challenges and developing new materials and technologies that can further improve the performance and efficiency of OPV cells.