Structural changes during 3D printing of bioderived and synthetic thermoplastic materials

Effect of Aging on Tensile and Chemical Properties of Polylactic Acid and Polylactic Acid-Like Polymer Materials for Additive Manufacturing

Additive manufacturing, with its fast development and application of polymeric materials, led to the wide utilization of polylactic acid (PLA) materials. As a biodegradable and biocompatible aliphatic polyester, produced from renewable sources, PLA is widely used in different sectors, from industry to medicine and science. The aim of this research is to determine the differences between two forms of the PLA material, i.e., fused deposition modeling (FDM) printed filament and digital light processing (DLP) printed resin, followed by aging due to environmental and hygiene maintenance conditions for a period of two months. Specimens underwent 3D scanning, tensile testing, and Fourier transform infrared (FTIR) spectrometry to obtain insights into the material changes that occurred. Two-way Analysis of Variance (ANOVA) statistical analysis was subsequently carried out to determine the statistical significance of the determined changes. Significant impairment can be observed in the dimensional accuracies between both materials, whether they are non-aged or aged. The mechanical properties fluctuated for aged FDM specimens: 15% for ultimate tensile stress, 15% for elongation at yield, and 12% for elastic modulus. Regarding the DLP aged specimens, the UTS decreased by 61%, elongation at yield by around 61%, and elastic modulus by 62%. According to the FTIR spectral analysis, the PLA materials degraded, especially in the case of resin specimens. Aging also showed a significant influence on the elastic modulus, ultimate tensile stress, elongation at yield, elongation at break, and toughness of both materials, which was statistically shown by means of a two-way ANOVA test. The data collected in this research give a better understanding of the underlying aging mechanism of PLA materials.

Effect of Shock-Variable Environmental Temperature and Humidity Conditions on 3D-Printed Polymers for Tensile Properties

The article presents the research results on the influence of variable shock conditions, such as temperature and water, thus reflecting shock atmospheric conditions during freezing and thawing, on the properties of samples produced using 3D printing technology from commonly used materials such as ABS, HIPS, PLA, and ASA. Understanding how different environmental conditions affect the quality, reliability, and durability of 3D prints can help to optimize the printing process and provide valuable information about their application possibilities. Tests related to the strength of the materials, such as static tensile testing, Charpy impact testing, and evaluation of structures, were carried out using a scanning electron microscope (SEM). Changes in chemical properties were measured by performing tests such as FTIR and TGA. Variations in chemical properties were measured by performing tests such as FTIR and TGA. One shock cycle lasting 7 days was sufficient to alter the properties of 3D prints, with the extent of changes depending on the material, as summarized in the test results.

Effect of Modification and Hydrothermal Ageing on Properties of 3D-Printed Wood Flour-Poly(butylene succinate)-Poly(lactic acid) Biocomposites

Wood flour-poly(butylene succinate)-poly(lactic acid) biocomposite samples were prepared by fused-deposition-molding 3D-printing technology, and modifications with glycerol and a silane coupling agent (KH550) were carried out. The samples were then hydrothermally aged. Modification with glycerol and KH550 enhanced the hydrophilicity of the samples and increased their tensile strength. Hydrothermal aging clearly whitened the surfaces of all the samples and made them more hydrophobic. Meanwhile, their tensile properties and thermal stability became poor; a higher hydrothermal aging temperature affected the mechanical properties more negatively. The modified samples turned out to be more resistant to the hydrothermal aging, and modification with KH550 could improve the anti-hydrothermal aging properties of the samples better than that with glycerol, where the tensile properties and the cross-sectional morphologies of the fractured specimens were concerned. Generally, the effects of hydrothermal aging temperature on the physico-mechanical properties of the printed specimens were greater than those by hydrothermal aging time.

Degradation Behavior of 3D-Printed Residue of Astragalus Particle/Poly(Lactic Acid) Biocomposites under Soil Conditions

Astragalus is widely cultivated in China, and the residue of Astragalus particles (ARP) can be used as reinforcements in fused filament-fabricated (FFF) natural fiber/Poly(lactic acid)(PLA) biocomposites. To clarify the degradation behavior of such biocomposites, 3D-printed 11 wt% ARP/PLA samples were buried in soil, and the effects of soil burial duration on the physical appearance, weight, flexural properties, morphology, thermal stability, melting, and crystallization properties were investigated. At the same time, 3D-printed PLA was chosen as a reference. The results showed that, with prolonged soil burial, the transparency of PLA decreased (but not obviously), while the surface photographs of ARP/PLA became gray with some black spots and crevices; especially after 60 days, the color of the samples became extremely heterogeneous. After soil burial, the weight, flexural strength, and flexural modulus of the printed samples all reduced, and greater losses happened to ARP/PLA pieces than pure PLA. With an increase in soil burial time, the glass transition, cold crystallization, and melting temperatures, as well as the thermal stability of PLA and ARP/PLA samples, all increased gradually. Additionally, soil burial had a greater effect on the thermal properties of ARP/PLA. The results showed that the degradation behavior of ARP/PLA was more significantly affected by soil burial than the behavior of PLA. Additionally, ARP/PLA more easily degraded in soil than PLA.

Portable smartphone integrated 3D-Printed electrochemical sensor for nonenzymatic determination of creatinine in human urine

3D printing technologies are an attractive for fabricating electrochemical sensors due to their ease of operation, freedom of design, fast prototyping, low waste, and low cost. We report the fabrication of a simple 3D-printed electrochemical sensing device for non-enzymatic detection of creatinine, an important indicator of renal function. To create the 3D-printed electrodes (3DE), carbon black/polylactic acid (CB/PLA) composite filament was used. The 3DE was activated using 0.5 M NaOH via amperometry prior to use to improve electrochemical performance. To give selectivity for creatinine, the activated 3DE was modified with a copper oxide nanoparticle-ionic liquid/reduced graphene oxide (CuO-IL/rGO) composite. The modified 3DE was characterized using microscopy and electrochemistry. Cyclic voltammetry and amperometry were used to evaluate sensor performance. The modified 3DE provided electrocatalytic activity towards creatinine without enzymes. Under optimal conditions, the modified 3DE directly coupled with a portable smartphone potentiostat exhibited the linear detection range of 0.5-35.0 mM, and the limit of detection was 37.3 μM, which is sufficient for detecting creatinine in human urine samples. Furthermore, the other physiological compounds present in human urine were not detected on the modified 3DE. Therefore, the modified 3DE could be a tool for effective creatinine screening in the urine.

Structural composite based on 3D printing polylactic acid/carbon fiber laminates (PLA/CFRC) as an alternative material for femoral stem prosthesis

In recent years, surgical procedures for hip prostheses have increased. These implants are manufactured with materials with high stiffness compared to the bone, causing bone loss or aseptic loosening. This research proposes an alternative structural composite consisting of 3D-printing polylactic acid layers and carbon fiber laminates (PLA/CFRC) with potential application in prosthetic implants. Fourier-transform infrared spectroscopy (FTIR) achieved to characterize starting materials and structural composites revealed secondary chemical interactions between the carbonyl group of PLA with the hydroxyl group of epoxy resin from CFRC. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) results show both components (PLA and CFRC) influence the structural composite's thermal behavior, observed in the temperatures of degradation, glass transition, and melting. Furthermore, the composite reached cell viability above 80%, a tensile modulus of 19.29 ± 0.48 GPa and tensile strength of 238.91 ± 25.95 MPa, with mechanical properties very similar to the bone. The results of this study demonstrated that the proposed PLA/CFRC composite can be used as candidate base material for the manufacturing of a hip femoral stem prostheses.

Recovery of Waste Material from Biobags: 3D Printing Process and Thermo-Mechanical Characteristics in Comparison to Virgin and Composite Matrices

The purpose of this study is to limit the environmental impact of packaging applications by promoting the recycling of waste products and the use of sustainable materials in additive manufacturing technology. To this end, a commercial polylactide acid (PLA)-based filament derived from waste production of bio-bags is herein considered. For reference, a filament using virgin PLA and one using a wood-based biocomposite were characterized as well. Preliminary testing involved infrared spectroscopy, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The effect of printing parameters (namely bed temperature, layer thickness, top surface layers, retraction speed, and distance) on the final aesthetics of 3D printed parts was verified. The results allow us to attest that the thermal properties of recycled polymer are comparable to those of virgin PLA and biocomposite. In the case of recycled polymer, after the extrusion temperature, bed temperature, and printing speed are estabilished the lowest allowable layer thickness and an appropriate choice of retraction movements are required in order to realize 3D-printed objects without morphological defects visible to the naked eyes. In the case of wood biocomposite, the printing process was complicated by frequent obstructions, and in none of the operating conditions was it possible to obtain an aesthetically satisfying piece of the chosen geometry (Lego-type bricks) Finally, mechanical testing on the 3D printed parts of each system showed that the recycled PLA behaves similarly to virgin and wood/PLA filaments.

The Influence of Solar Sintering on Copper Heat Exchanger Parts with Controlled 3D-Printed Morphology

From a scientific point of view, heat transfer is different in solar furnaces compared with classical ones and the influence of direct concentrated solar radiation on sintered parts needs to be studied in detail to determine the feasibility of solar furnaces in manufacturing small workpieces. This study was performed on cylindrical samples with controlled morphology obtained by a powder metallurgy 3D printing technique. All samples were heated with a heating rate of 120 ± 10 °C/minute, with 0, 1, 2, 3, 4 and 5 min holding times at 900 °C and 930 °C. The morphology of the samples was analyzed microscopically, the microhardness was determined before and after sintering, and the results were correlated with the sintering parameters (temperature, heating rate and holding time). The best results were obtained at 930 °C with 5 min holding time from the microhardness value and microstructure point of view.

Solid Dispersion Formulations by FDM 3D Printing-A Review

Additive manufacturing (AM) is revolutionizing the way medicines are designed, manufactured, and utilized. Perhaps, AM appears to be ideal for the fit-for-purpose manufacturing of medicines in contrast to the several disadvantages associated with the conventional fit-for-all mass production that accounts for less than 50% of pharmacotherapeutic treatment/management of diseases especially among children and elderly patients, as well as patients with special needs. In this review, we discuss the current trends in the application of additive manufacturing to prepare personalized dosage forms on-demand focusing the attention on the relevance of coupling solid dispersion with FDM 3D printing. Combining the two technologies could offer many advantages such as to improve the solubility, dissolution, and oral bioavailability of poorly soluble drugs in tandem with the concept of precision medicine and personalized dosing and to address the dilemma of commercial availability of FDM filaments loaded with Class II and/or Class IV drugs. However, thermal treatment especially for heat-sensitive drugs, regulatory, and ethical obligations in terms of quality control and quality assurance remain points of concern. Hence, a concerted effort is needed between the scientific community, the pharmaceutical industries, the regulatory agencies, the clinicians and clinical pharmacists, and the end-users to address these concerns.

Laboratory and field scale biodegradability assessment of biocomposite cellphone cases for end-of-life management

The increase in production of biobased plastics as a replacement for fossil fuel-based plastics has created the need for studies to assess their degradation under various conditions. However, developing reliable laboratory and field-testing protocols for biobased materials and products still requires extensive research. In this study, the biodegradability of a biocomposite consumer product, smart cellphone case, was determined under laboratory scale anaerobic (38 °C) and composting assays (58 °C) as well as under field scale (60-67 °C) composting conditions. The laboratory scale composting assay was conducted for 46 days using cellphone cases with dimensions of 7 × 3.5 × 0.2 and 4.6 × 3.5 × 0.2 cm, which achieved approximately 20% biodegradation. The field scale composting conditions achieved 55% weight loss of cellphone cases in 80 days. The subsequent anaerobic biodegradation assays contained three different sized (grinded, cut into 2 × 2 × 0.2 and 4 × 4 × 0.2 cm pieces) biocomposite cellphone cases conducted under mesophilic conditions for 169 days. Among the conditions tested, the size of cellphone cases did not cause a significant difference in biodegradation under anaerobic conditions. Anaerobic digestion conditions yielded only 6-8% biodegradation, which was significantly lower than that of composting. The results agree with literature on conventional waste streams stating that aerobic microbial processes are more effective to break down complex substrates, similar to biocomposite cellphone cases tested, than their anaerobic counterparts.

Colour Fastness to Various Agents and Dynamic Mechanical Characteristics of Biocomposite Filaments and 3D Printed Samples

The aim of the study was to analyse the colour fastness of 3D printed samples that could be used as decorative or household items. Such items are often fabricated with 3D printing. The colour of filaments affects not only the mechanical properties, but also the appearance and user satisfaction. Samples of biocomposite filaments (PLA and PLA with added wood and hemp fibres) were used. First, the morphological properties of the filaments and 3D printed samples were analysed and then, the colour fastness against different agents was tested (water, oil, detergent, light and elevated temperature). Finally, the dynamic mechanical properties of the filaments and 3D printed samples were determined. The differences in the morphology of the filaments and 3D printed samples were identified with SEM analysis. The most obvious differences were observed in the samples with wood fibres. All printed samples showed good resistance to water and detergents, but poorer resistance to oil. The sample printed with filaments with added wood fibres showed the lowest colour fastness against light and elevated temperatures. Compared to the filaments, the glass transition of the printed samples increased, while their stiffness decreased significantly. The lowest elasticity was observed in the samples with wood fibres. The filaments to which hemp fibres were added showed the reinforcement effect. Without the influence on their elasticity, the printed samples can be safely used between 60 and 65 °C.

Supercritical Impregnation of PLA Filaments with Mango Leaf Extract to Manufacture Functionalized Biomedical Devices by 3D Printing

Polylactic Acid (PLA) filaments impregnated with ethanolic mango leaves extract (MLE) with pharmacological properties were obtained by supercritical impregnation. The effects of pressure, temperature and amount of extract on the response variables, i.e., swelling, extract loading and bioactivity of the PLA filaments, were determined. The analysis of the filaments biocapacities revealed that impregnated PLA filaments showed 11.07% antidenaturant capacity and 88.13% antioxidant activity, which after a 9-day incubation shifted to 30.10% and 9.90%, respectively. Subsequently, the same tests were conducted on printed samples. Before their incubation, the printed samples showed 79.09% antioxidant activity and no antidenaturant capacity was detected. However, after their incubation, the antioxidant activity went down to only 2.50%, while the antidenaturant capacity raised up to 23.50%. The persistence of the bioactive properties after printing opens the possibility of using the functionalized PLA filaments as the feed for a three-dimensional (3D) printer.

Preparation and characterization of 3D printed PLA microneedle arrays for prolonged transdermal drug delivery of estradiol valerate

Biodegradable polymeric microneedle arrays (BPMNAs) could be explored as potential devices for transdermal drug delivery, which can provide a painless and safe drug delivery method. BPMNAs could also provide high drug-loading capacity and prolonged drug delivery once integrated with a drug reservoir. However, the fabrication of MNAs with a drug reservoir is expensive and requires complicated procedures. The present study was conducted to describe the preparation of a reservoir-based BPMNA containing estradiol valerate using polylactic acid (PLA) with the combination of FDM 3D printing and injection volume filling techniques. The tip size of the 3D printed needles decreased to 173 μm utilizing a chemical etching process. The content of estradiol valerate loaded in the 3D printed PLA MNAs was 29.79 ± 0.03 mg, and the release was in a prolonged manner for up to 7 days. The results of mechanical tests revealed that the force needed for the 3D printed PLA MNAs fracture (900 N) was significantly higher than that needed for their skin penetration (4 N). The successful penetration of 3D printed PLA MNAs through the stratum corneum was confirmed via penetration test, methylene blue staining, and histological examination. The results showed that 3D printed PLA MNAs can penetrate into the skin without reaching to the dermal nerves and puncture of blood vessels. In conclusion, in the current study, we explored the practicability of the preparation of drug loaded reservoir-based BPMNAs using the combination of FDM 3D printing and injection volume filling techniques for painless and prolonged transdermal drug delivery.

Structure-function assessment of 3D-printed porous scaffolds by a low-cost/open source fused filament fabrication printer

Additive manufacturing encompasses a plethora of techniques to manufacture structures from a computational model. Among them, fused filament fabrication (FFF) relies on heating thermoplastics to their fusion point and extruding the material through a nozzle in a controlled pattern. FFF is a suitable technique for tissue engineering, given that allows the fabrication of 3D-scaffolds, which are utilized for tissue regeneration purposes. The objective of this study is to assess a low-cost/open-source 3D printer (In-House), by manufacturing both solid and porous samples with relevant microarchitecture in the physiological range (100-500 μm pore size), using an equivalent commercial counterpart for comparison. For this, compressive tests in solid and porous scaffolds manufactured in both printers were performed, comparing the results with finite element analysis (FEA) models. Additionally, a microarchitectural analysis was done in samples from both printers, comparing the measurements of both pore size and porosity to their corresponding computer-aided design (CAD) models. Moreover, a preliminary biological assessment was performed using scaffolds from our In-House printer, measuring cell adhesion efficiency. Finally, Fourier transform infrared spectroscopy - attenuated total reflectance (FTIR-ATR) was performed to evaluate chemical changes in the material (polylactic acid) after fabrication in each printer. The results show that the In-House printer achieved generally better mechanical behavior and resolution capacity than its commercial counterpart, by comparing with their FEA and CAD models, respectively. Moreover, a preliminary biological assessment indicates the feasibility of the In-House printer to be used in tissue engineering applications. The results also show the influence of pore geometry on mechanical properties of 3D-scaffolds and demonstrate that properties such as the apparent elastic modulus (E_app) can be controlled in 3D-printed scaffolds.

Bio-Based Packaging Materials Containing Substances Derived from Coffee and Tea Plants

The aim of the research was to obtain intelligent and eco-friendly packaging materials by incorporating innovative additives of plant origin. For this purpose, natural substances, including green tea extract (polyphenon 60) and caffeic acid, were added to two types of biodegradable thermoplastics (Ingeo™ Biopolymer PLA 4043D and Bioplast GS 2189). The main techniques used to assess the impact of phytocompounds on materials’ thermal properties were differential scanning calorimetry (DSC) and thermogravimetry (TGA), which confirmed the improved resistance to thermo-oxidation. Moreover, in order to assess the activity of applied antioxidants, the samples were aged using a UV aging chamber and a weathering device, then retested in terms of dynamic mechanical properties (DMA), colour changing, Vicat softening temperature, and chemical structure, as studied using FT-IR spectra analysis. The results revealed that different types of aging did not cause significant differences in thermo-mechanical properties and chemical structure of the samples with natural antioxidants but induced colour changing. The obtained results indicate that polylactide (PLA) and Bioplast GS 2189, the plasticizer free thermoplastic biomaterial containing polylactide and starch (referred to as sPLA in the present article), both with added caffeic acid and green tea extract, can be applied as smart and eco-friendly packaging materials. The composites reveal better thermo-oxidative stability with reference to pure materials and are able to change colour as a result of the oxidation process, especially after UV exposure, providing information about the degree of material degradation.

Influence of Internal Innovative Architecture on the Mechanical Properties of 3D Polymer Printed Parts

The utilization of polymer-based materials is quickly expanding. The enterprises of today are progressively seeking techniques to supplant metal parts with polymer-based materials as a result of their light weight, simple support and modest costs. The ceaselessly developing requirement for composite materials with new or enhanced properties brings about the preparation of different polymer mixes with various arrangements, morphologies and properties. Fused filament fabrication processes such as 3D-printing are nowadays shaping the actual pathway to a full pallet of materials, from art-craft to biomaterials. In this study, the structural and mechanical behavior of three types of commercially available filaments comprised of synthetic poly(acrylonitrile-co-butadiene-co-styrene) (ABS), poly(lactic acid) (PLA) and poly(lactic acid)/polyhydroxyalkanoate reinforced with bamboo wood flour composite (PLA/PHA BambooFill) were assessed through mechanical testing and optical microscopy, aiming to understand how the modifications that occur in the printed models with internal architecture are influencing the mechanical properties of the 3D-printed material. It has been determined that the material printed from PLA presents the highest compression strength, three-point bending and shock resistance, while the ABS shows the best tensile strength performance. A probability plot was used to verify the normality hypothesis of data for the tensile strength, in conjunction with the Anderson-Darling statistic test. The results of the statistic indicated that the data were normally distributed and that there is a marked influence of the internal architecture of the 3D-printed models on the mechanical properties of the printed material.

Effect of Reconstruction Algorithm on the Identification of 3D Printing Polymers Based on Hyperspectral CT Technology Combined with Artificial Neural Network

Hyperspectral X-ray CT (HXCT) technology provides not only structural imaging but also the information of material components therein. The main purpose of this study is to investigate the effect of various reconstruction algorithms on reconstructed X-ray absorption spectra (XAS) of components shown in the CT image by means of HXCT. In this paper, taking 3D printing polymer as an example, seven kinds of commonly used polymers such as thermoplastic elastomer (TPE), carbon fiber reinforced polyamide (PA-CF), acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), ultraviolet photosensitive resin (UV9400), polyethylene terephthalate glycol (PETG), and polyvinyl alcohol (PVA) were selected as samples for hyperspectral CT reconstruction experiments. Seven kinds of 3D printing polymer and two interfering samples were divided into a training set and test sets. First, structural images of specimens were reconstructed by Filtered Back-Projection (FBP), Algebra Reconstruction Technique (ART) and Maximum-Likelihood Expectation-Maximization (ML-EM). Secondly, reconstructed XAS were extracted from the pixels of region of interest (ROI) compartmentalized in the images. Thirdly, the results of principal component analysis (PCA) demonstrated that the first four principal components contain the main features of reconstructed XAS, so we adopted Artificial Neural Network (ANN) trained by the reconstructed XAS expressed by the first four principal components in the training set to identify that the XAS of corresponding polymers exist in both of test sets from the training set. The result of ANN displays that FBP has the best performance of classification, whose ten-fold cross-validation accuracy reached 99%. It suggests that hyperspectral CT reconstruction is a promising way of getting image features and material features at the same time, which can be used in medical imaging and nondestructive testing.

Thermal Analysis of Aliphatic Polyester Blends with Natural Antioxidants

The aim of this research was to enhance thermal stability of aliphatic polyester blends via incorporation of selected natural antioxidants of plant origin. Thermal methods of analysis, including differential scanning calorimetry (DSC) and thermogravimetry (TGA), are significant tools for estimating the stabilization effect of polyphenols in a polymer matrix. Thermal stability was determined by analyzing thermogravimetric curves. Polymers with selected antioxidants degraded more slowly with rising temperature in comparison to reference samples without additives. This property was also confirmed by results obtained from differential scanning calorimetry (DSC), where the difference between the oxidation temperatures of pure material and polymer with natural stabilizers was observed. According to the results, the materials with selected antioxidants, including trans-chalcone, flavone and lignin have higher oxidation temperature than the pure ones, which confirms that chosen phytochemicals protect polymers from oxidation. Moreover, based on the colour change results or FT-IR spectra analysis, some of the selected antioxidants, including lignin and trans-chalcone, can be utilized as colorants or aging indicators. Taking into account the data obtained, naturally occurring antioxidants, including polyphenols, can be applied as versatile pro-ecological additives for biodegradable and bio-based aliphatic polyesters to obtain fully environmentally friendly materials dedicated for packaging industry.

Review of Polymeric Materials in 4D Printing Biomedical Applications

The purpose of 4D printing is to embed a product design into a deformable smart material using a traditional 3D printer. The 3D printed object can be assembled or transformed into intended designs by applying certain conditions or forms of stimulation such as temperature, pressure, humidity, pH, wind, or light. Simply put, 4D printing is a continuum of 3D printing technology that is now able to print objects which change over time. In previous studies, many smart materials were shown to have 4D printing characteristics. In this paper, we specifically review the current application, respective activation methods, characteristics, and future prospects of various polymeric materials in 4D printing, which are expected to contribute to the development of 4D printing polymeric materials and technology.

FDM 3D Printing of Polymers Containing Natural Fillers: A Review of their Mechanical Properties

As biodegradable thermoplastics are more and more penetrating the market of filaments for fused deposition modeling (FDM) 3D printing, fillers in the form of natural fibers are convenient: They have the clear advantage of reducing cost, yet retaining the filament biodegradability characteristics. In plastics that are processed through standard techniques (e.g., extrusion or injection molding), natural fibers have a mild reinforcing function, improving stiffness and strength, it is thus interesting to evaluate whether the same holds true also in the case of FDM produced components. The results analyzed in this review show that the mechanical properties of the most common materials, i.e., acrylonitrile-butadiene-styrene (ABS) and PLA, do not benefit from biofillers, while other less widely used polymers, such as the polyolefins, are found to become more performant. Much research has been devoted to studying the effect of additive formulation and processing parameters on the mechanical properties of biofilled 3D printed specimens. The results look promising due to the relevant number of articles published in this field in the last few years. This notwithstanding, not all aspects have been explored and more could potentially be obtained through modifications of the usual FDM techniques and the devices that have been used so far.