La0.7Sr0.3MnO3 Perovskites for Oxygen Reduction in Zn-Air Batteries: Enhanced by In Situ Glucose Regulation

The actual ORR catalytic activity of perovskite materials is significantly lower than the theoretical value due to their inherently low specific surface area and significant segregation of inactive oxygen ions on the surface. This study reports a sol-gel synthesis approach that employs glucose as a structural regulator to fabricate La0.7Sr0.3MnO3 (LSM) perovskites. Compared with the original LSM (12.56 m2·g-1), LSM-Y2 exhibits a higher specific surface area (19.43 m2·g-1) and enhanced ORR catalytic activity. Electrochemical results show that the initial potential and half-wave potential of LSM-Y2 are positively shifted by 35 and 85 mV, respectively, with a 1.29-fold increase in intrinsic catalytic activity. Additionally, the performance of the Zn-air batteries is superior to that of the original LSM, with a peak power density of 115 mW·cm-2 and an energy density of 858 Wh·kg-1. The enhanced ORR catalytic activity of LSM-Y2 is attributed to the optimization of Mn eg orbital occupancy on the catalyst surface, facilitated by glucose introduction, and the improved adsorption of oxygen intermediates, resulting from the increased oxygen vacancy concentration. Additionally, the increased specific surface area and porosity of LSM-Y2 provided more active sites for the catalytic process, further enhancing ORR performance. This study not only elucidates the mechanism by which glucose influences the ORR catalytic activity of La0.7Sr0.3MnO3 perovskite but also presents a strategy for developing perovskite catalysts with superior ORR catalytic performance.

Sulfonated reduced graphene oxide encapsulated perovskite-type ErCoFe oxide nanoparticles for efficient electrochemical water oxidation

Perovskite oxides play a vital role as electrocatalysts in water oxidation due to their flexible and unique electronic structures. In this work, Er-based perovskites ErCo1-xFexO3-δ (x = 0.0, 0.1, 0.3, 0.5, 0.7, and 1.0) denoted as EC, ECF-0.9, ECF-0.7, ECF-0.5, ECF-0.3, and EF, respectively, are synthesized by the sol-gel method. Then, ECF-0.9 is supported on sulfonated reduced graphene oxide (S-rGO) by a hydrothermal method, with weight ratios of 1 : 1 and 3 : 1 of ECF/0.9 to S-rGO (shown as ECF-0.9/S-rGO(50%) and ECF-0.9/S-rGO(75%), respectively). The structural properties and the morphology of the synthesized materials are studied using a series of different techniques. The prepared perovskites are then used as electrode materials for electrochemical water oxidation. ECF-0.9 reveals better activity than pure EF, EC, and other perovskite oxides in terms of overpotential, Tafel slope, electrochemically active surface area (ECSA), and charge transfer resistance (Rct) values. Interestingly, when the optimized perovskite oxide catalyst ECF-0.9 is decorated on S-rGO sheets, the water oxidation activity is significantly improved. ECF-0.9/S-rGO(75%) exhibits superior activity for water oxidation with an overpotential of 290 mV@10 mA cm-2 and a Tafel slope of 41 mV dec-1. Finally, overall water splitting with ECF-0.9/S-rGO(75%) as the anode electrode shows a low electrolysis voltage of 1.60 V, alongside excellent stability for 20 h.

Improving the Oxygen Evolution Reaction Kinetics in Zn-Air Battery by Iodide Oxidation Reaction

Zinc-air batteries (ZABs) have garnered considerable attention as a highly promising contender in the field of energy storage and conversion. Nevertheless, their performance is considerably impeded by the proliferation of dendrites on the Zinc anode and the slow kinetics of the redox reaction on the air cathode. Herein, taking Ag30%@LaCoO3 (Ag30%@LCO) heterojunction catalyst as the cathode, it is demonstrated that adding KI additives to the alkaline electrolyte can not only enhance the oxygen electrocatalytic reaction but also inhibit the formation of zinc anode dendrites, thereby achieving a comprehensive improvement in the performance of ZABs. Under the action of the KI additive, the optimized Ag30%@LCO catalyst shows a decreased overpotential from 460 to 220 mV at j = 10 mA cm-2, while the assembled ZAB shows reduced charging potential (1.8 V), and long cycle stability (180 h). Furthermore, the morphology characterization results indicate a reduction in dendrites on the Zn anode. Both experimental and calculated results indicate that the presence of I- as a reaction modifier alters the trajectory of the conventional oxygen evolution reaction, resulting in a more thermodynamically favorable pathway. The introduction of KI additives as electrolytes provides a straightforward approach to developing comprehensively improved ZABs.

Enhanced Electrocatalytic Activity of Amorphized LaCoO3 for Oxygen Evolution Reaction

Amorphous inorganic perovskites have attracted significant attention as efficient electrocatalysts due to their unique structural flexibility and good catalytic activity. In particular, the disordered structure and a surface rich in defects such as oxygen vacancies can contribute to the superior electrocatalytic activity of amorphous oxides compared to their crystalline counterpart. In this work, we report the synthesis of LaCoO3, followed by an amorphization process through urea reduction with tailored modifications. The as-synthesized catalysts were thoroughly tested for their performance in oxygen evolution reaction (OER), Remarkably, the amorphous LaCoO3 synthesized at 450 °C (referred to as LCO-4) exhibits excellent OER catalytic activity. At an overpotential of 310 mV, it achieved a current density of 10 mA/cm-2, exceedingly fast to 1 A/cm-2 at an overpotential of only 460 mV. Moreover, LCO-4 exhibited several advantageous features compared to pristine LaCoO3 and LaCoO3 amorphized at other two temperatures (350 °C, LCO-3, and 550 °C, LCO-5). The amorphized LCO-4 catalyst showed a higher electrochemically active surface area, a key factor in boosting catalytic performance. Additionally, LCO-4 demonstrated the lowest Tafel slope of 70 mVdec-1, further highlighting its exceptional OER activity. Furthermore, the long-term stability of LCO-4 is notably superior than pristine LaCoO3 (LCO-P) and the other amorphized samples (LCO-3 and LCO-5). The enhanced catalytic activity of LCO-4 can be attributed to its unique disordered structure, small crystallite size, and higher concentration of oxygen vacancies in the final catalyst.

Tailored (La0.2Pr0.2Nd0.2Tb0.2Dy0.2)2Ce2O7 as a Highly Active and Stable Nanocatalyst for the Oxygen Evolution Reaction

Designing highly active and robust catalysts for the oxygen evolution reaction is key to improving the overall efficiency of the water splitting reaction. It has been previously demonstrated that evaporation induced self-assembly (EISA) can be used to synthesize highly porous and high surface area cerate-based fluorite nanocatalysts, and that substitution of Ce with 50% rare earth (RE) cations significantly improves electrocatalyst activity. Herein, the defect structure of the best performing nanocatalyst in the series are further explored, Nd2Ce2O7, with a combination of neutron diffraction and neutron pair distribution function analysis. It is found that Nd3 + cation substitution for Ce in the CeO2 fluorite lattice introduces higher levels of oxygen Frenkel defects and induces a partially reduced RE1.5Ce1.5O5 + x phase with oxygen vacancy ordering. Significantly, it is demonstrated that the concentration of oxygen Frenkel defects and improved electrocatalytic activity can be further enhanced by increasing the compositional complexity (number of RE cations involved) in the substitution. The resulting novel compositionally-complex fluorite- (La0.2Pr0.2Nd0.2Tb0.2Dy0.2)2Ce2O7 is shown to display a low OER overpotential of 210 mV at a current density of 10 mAcm-2 in 1M KOH, and excellent cycling stability. It is suggested that increasing the compositional complexity of fluorite nanocatalysts expands the ability to tailor catalyst design.

Strategic Design and Insights into Lanthanum and Strontium Perovskite Oxides for Oxygen Reduction and Oxygen Evolution Reactions

Perovskite oxides exhibit bifunctional activity for both oxygen reduction (ORR) and oxygen evolution reactions (OER), making them prime candidates for energy conversion in applications like fuel cells and metal-air batteries. Their intrinsic catalytic prowess, combined with low-cost, abundance, and diversity, positions them as compelling alternatives to noble metal and metal oxides catalysts. This review encapsulates the nuances of perovskite oxide structures and synthesis techniques, providing insight into pivotal active sites that underscore their bifunctional behavior. The focus centers on the breakthroughs surrounding lanthanum (La) and strontium (Sr)-based perovskite oxides, specifically their roles in zinc-air batteries (ZABs). An introduction to the mechanisms of ORR and OER is provided. Moreover, the light is shed on strategies and determinants central to optimizing the bifunctional performance of La and Sr-based perovskite oxides.

Mesoporous RE0.5Ce0.5O2-x Fluorite Electrocatalysts for the Oxygen Evolution Reaction

Developing highly active and stable electrocatalysts for the oxygen evolution reaction (OER) is key to improving the efficiency and practical application of various sustainable energy technologies including water electrolysis, CO2 reduction, and metal air batteries. Here, we use evaporation-induced self-assembly (EISA) to synthesize highly porous fluorite nanocatalysts with a high surface area. In this study, we demonstrate that a 50% rare-earth cation substitution for Ce in the CeO2 fluorite lattice improves the OER activity and stability by introducing oxygen vacancies into the host lattice, which results in a decrease in the adsorption energy of the OH* intermediate in the OER. Among the binary fluorite compositions investigated, Nd2Ce2O7 is shown to display the lowest OER overpotential of 243 mV, achieved at a current density of 10 mA cm-2, and excellent cycling stability in an alkaline medium. Importantly, we demonstrate that rare-earth oxide OER electrocatalysts with high activity and stability can be achieved using the EISA synthesis route without the incorporation of transition and noble metals.

The Multifunctionality of Lanthanum-Strontium Cobaltite Nanopowder: High-Pressure Magnetic Studies and Excellent Electrocatalytic Properties for OER

Simultaneous study of magnetic and electrocatalytic properties of cobaltites under extreme conditions expands the understanding of physical and chemical processes proceeding in them with the possibility of their further practical application. Therefore, La0.6Sr0.4CoO3 (LSCO) nanopowders were synthesized at different annealing temperatures tann = 850-900 °C, and their multifunctional properties were studied comprehensively. As tann increases, the rhombohedral perovskite structure of the LSCO becomes more single-phase, whereas the average particle size and dispersion grow. Co3+ and Co4+ are the major components. It has been found that LSCO-900 shows two main Curie temperatures, TC1 and TC2, associated with a particle size distribution. As pressure P increases, average ⟨TC1⟩ and ⟨TC2⟩ increase from 253 and 175 K under ambient pressure to 268 and 180 K under P = 0.8 GPa, respectively. The increment of ⟨dTC/dP⟩ for the smaller and bigger particles is sufficiently high and equals 10 and 13 K/GPa, respectively. The magnetocaloric effect in the LSCO-900 nanopowder demonstrates an extremely wide peak δTfwhm > 50 K that can be used as one of the composite components, expanding its working temperature window. Moreover, all LSCO samples showed excellent electrocatalytic performance for the oxygen evolution reaction (OER) process (overpotentials of only 265-285 mV at a current density of 10 mA cm-2) with minimal η10 for LSCO-900. Based on the experimental data, it was concluded that the formation of a dense amorphous layer on the surface of the particles ensures high stability as a catalyst (at least 24 h) during electrolysis in 1 M KOH electrolyte.

Application of response surface methodology for optimization of the test condition of oxygen evolution reaction over La0.8Ba0.2CoO3 perovskite-active carbon composite

The Experimental Design was applied to optimize the electrocatalytic activity of La0.8Ba0.2CoO3 perovskite oxide/Active Carbon composite material in the alkaline solution for the Oxygen Evolution Reaction. After the preparation of La0.8Ba0.2CoO3, and structural characterizations, the experimental design was utilized to determine the optimal amount of the composite material and testing conditions. The overpotential was defined as the response variable, and the mass ratio of perovskite/active carbon, Potassium hydroxide (KOH) concentration, and Poly(vinylidene fluoride) (PVDF) amount were considered effective parameters. The significance of model terms is demonstrated by P-values less than 0.0500. The proposed prediction model determined the optimal amounts of 0.665 mg of PVDF, a KOH concentration of 0.609 M, and A perovskite/Active Carbon mass ratio of 2.81 with 308.22 mV overpotential (2.27% greater than the actual overpotential). The stability test of the optimized electrode material over 24 h suggests that it could be a good candidate electrocatalyst for OER with reusability potential.

Enhancement of Electrocatalytic Oxygen Reduction Reaction and Oxygen Evolution Reaction by Introducing Lanthanum Species in the Carbon Shell

The development of cost-effective non-noble metal electrocatalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) opens up the possibility for sustainable energy systems. Herein, we report a surface overcoating strategy with lanthanum organic complex (La-OC) as the precursor to prepare lanthanum species (La-SPc) encapsulated in nitrogen, fluorine, and sulfur self-doped porous carbon (NFS-PC) composites (La-SPc@NFS-PC) for efficient ORR and OER. The La-SPc is introduced not only as a promoter to increase the electrochemical stability of the La-SPc@NFS-PC catalysts but also to tailor the electronic structure of NFS-PC due to the unique electrochemical properties of La-SPc. In addition, the integration of La-SPc and NFS-PC can improve the electronic conductivity of composites by inducing electron redistribution and lowering the band gap, which is advantageous in enhancing the kinetics of charge transfer. Simultaneously, benefiting from the optimized porous structure and positive cooperation of La-SPc with NFS-PC shells, the obtained La-SPc@NFS-PC-3 delivers robust bifunctional ORR/OER activities and stabilities. More importantly, the Zn-air battery (ZAB) assembled with La-SPc@NFS-PC-3 demonstrates an outstanding power density (181.1 mW cm-2) and long cycling life, outperforming the commercial Pt/C. This work offers a rational approach to preparing high-efficiency rare-earth-based catalysts and provides potential applications in ZABs.

Research Progress of Perovskite-Based Bifunctional Oxygen Electrocatalyst in Alkaline Conditions

In light of the depletion of conventional energy sources, it is imperative to conduct research and development on sustainable alternative energy sources. Currently, electrochemical energy storage and conversion technologies such as fuel cells and metal-air batteries rely heavily on precious metal catalysts like Pt/C and IrO2, which hinders their sustainable commercial development. Therefore, researchers have devoted significant attention to non-precious metal-based catalysts that exhibit high efficiency, low cost, and environmental friendliness. Among them, perovskite oxides possess low-cost and abundant reserves, as well as flexible oxidation valence states and a multi-defect surface. Due to their advantageous structural characteristics and easily adjustable physicochemical properties, extensive research has been conducted on perovskite-based oxides. However, these materials also exhibit drawbacks such as poor intrinsic activity, limited specific surface area, and relatively low apparent catalytic activity compared to precious metal catalysts. To address these limitations, current research is focused on enhancing the physicochemical properties of perovskite-based oxides. The catalytic activity and stability of perovskite-based oxides in Oxygen Reduction Reaction/Oxygen Evolution Reaction (ORR/OER) can be enhanced using crystallographic structure tuning, cationic regulation, anionic regulation, and nano-processing. Furthermore, extensive research has been conducted on the composite processing of perovskite oxides with other materials, which has demonstrated enhanced catalytic performance. Based on these different ORR/OER modification strategies, the future challenges of perovskite-based bifunctional oxygen electrocatalysts are discussed alongside their development prospects.

Cationic Defect Engineering in Perovskite La2CoMnO6 for Enhanced Electrocatalytic Oxygen Evolution

The urgent need to promote the development of sustainable energy conversion requires exploration of highly efficient oxygen evolution reaction (OER) electrocatalysts. Defect engineering is a promising approach to address the inherent low electrical conductivity of metal oxides and limited reaction sites, for use in clean air applications and as electrochemical energy-storage electrocatalysts. In this article, oxygen defects are introduced into La₂CoMnO_6-δ perovskite oxides through the A-site cation defect strategy. By tuning the content of the A-site cation, oxygen defect concentration and corresponding electrochemical OER performance have been greatly improved. As a result, the defective La_1.8CoMnO_6-δ (L_1.8CMO) catalyst exhibits exceptional OER activity with an overpotential of 350 mV at 10 mA cm^-2, approximately 120 mV lower than that of the pristine perovskite. This enhancement can be attributed to the increase in surface oxygen vacancies, optimized e_g occupation of transition metal at the B-site, and enlarged Brunauer-Emmett-Teller surface area. The reported strategy facilitates the development of novel defect-mediated perovskites in electrocatalysis.

Tailoring Spin State of Perovskite Oxides by Fluorine Atom Doping for Efficient Oxygen Electrocatalysis

Promoting the initially deficient but economical catalysts to high-performing competitors is important for developing superior catalysts. Unlike traditional nano-morphology construction methods, this work focuses on intrinsic catalytic activity enhancement via heteroatom doping strategies to induce lattice distortion and optimize spin-dependent orbital interaction to alter charge transfer between catalysts and reactants. Experimentally, a series of different concentrations of fluorine-doped lanthanum cobaltate (F_x -LaCoO₃ ) exhibiting excellent electrocatalytic activity is synthesized, including a low overpotential of 390 mV at j = 10 mA cm^-2 for OER and a large half-wave potential of 0.68 V for ORR. Meanwhile, the assembled rechargeable Zn-air batteries deliver an excellent performance with a large specific capacity of 811 mAh/g_Zn under 10 mA cm^-2 and stability of charge/recharge (120 h). Theoretically, taking advantage of density functional theory calculations, it is found that the prominent OER/ORR performance arises from the spin state transition of Co³⁺ (Low spin state (LS, t_2g ⁶ e_g ⁰ ) → Intermediate spin state (IS, t_2g ⁵ e_g ¹ ) and the mediated d-band center upshift by F atom incorporation. This work establishes a novel avenue for designing superior electrocatalysts in perovskite-based oxides by regulating spin states.

New Undisputed Evidence and Strategy for Enhanced Lattice-Oxygen Participation of Perovskite Electrocatalyst through Cation Deficiency Manipulation

Oxygen evolution reaction (OER) is a key half-reaction in many electrochemical transformations, and efficient electrocatalysts are critical to improve its kinetics which is typically sluggish due to its multielectron-transfer nature. Perovskite oxides are a popular category of OER catalysts, while their activity remains insufficient under the conventional adsorbate evolution reaction scheme where scaling relations limit activity enhancement. The lattice oxygen-mediated mechanism (LOM) has been recently reported to overcome such scaling relations and boost the OER catalysis over several doped perovskite catalysts. However, direct evidence supporting the LOM participation is still very little because the doping strategy applied would introduce additional active sites that may mask the real reaction mechanism. Herein, a dopant-free, cation deficiency manipulation strategy to tailor the bulk diffusion properties of perovskites without affecting their surface properties is reported, providing a perfect platform for studying the contribution of LOM to OER catalysis. Further optimizing the A-site deficiency achieves a perovskite candidate with excellent intrinsic OER activity, which also demonstrates outstanding performance in rechargeable Zn-air batteries and water electrolyzers. These findings not only corroborate the key role of LOM in OER electrocatalysis, but also provide an effective way for the rational design of better catalyst materials for clean energy technologies.

Highly graphited carbon-coated FeTiO3 nanosheets in situ derived from MXene: an efficient bifunctional catalyst for Zn-air batteries

Developing high-efficiency and low-cost catalysts for the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) is of great significance for the commercialization of rechargeable metal-air batteries. Herein, we demonstrated the construction of graphited carbon-coated FeTiO₃ (FeTiO₃@C) via in situ annealing Ti₃C₂T_x nanosheets in a rusted-reactor and its efficient bifunctional activity for rechargeable Zn-air batteries (RZABs). The electron-transport dynamics of FeTiO₃@C can be improved by using highly conductive graphited carbon derived from Ti₃C₂T_x. The FeTiO₃@C catalyst annealed at 500 °C exhibits excellent OER and ORR activities. Specifically, FeTiO₃@C shows a low overpotential of 323 mV at 10 mA cm^-2 and a small Tafel slope of 53 mV dec^-1 towards the alkaline OER. During the OER process, FeTiO₃@C can be partially converted into highly active iron oxyhydroxide via in situ electrochemical reconstruction, which serves as the active species. After being assembled to RZABs, it shows an open-circuit potential of 1.33 V, a high trip efficiency of 63.4% and long-time cycling stability. This work can provide a new avenue for developing bifunctional electrocatalysts for RZABs used in portable devices.

Polar Layered Intermetallic LaCo2P2 as a Water Oxidation Electrocatalyst

We investigate LaCo₂P₂ as an electrocatalytic material for oxygen evolution reaction (OER) under alkaline and acidic conditions. This layered intermetallic material was prepared via Sn-flux high-temperature annealing. The electrocatalytic ink, prepared with the ball-milled LaCo₂P₂ catalyst at the mass loading of 0.25 mg/cm², shows OER activity at pH = 14, reaching current densities of 10, 50, and 100 mA/cm² under the overpotential of 400, 440, and 460 mV, respectively. Remarkably, the electrocatalytic performance remains constant for at least 4 days. Transmission electron microscopy reveals the formation of a catalytically active CoO_x shell around the pre-catalyst LaCo₂P₂ core during the alkaline OER. The core serves as a robust support for the in situ-formed electrocatalytic system. Similar studies under pH = 0 reveal the rapid deterioration of LaCo₂P₂, with the formation of LaPO₄ and amorphous cobalt oxide. This study shows the viability of layered intermetallics as stable OER electrocatalysts, although further developments are required to improve the electrocatalytic performance and increase the stability at lower pH values.

Surface-Electronic-Structure Reconstruction of Perovskite via Double-Cation Gradient Etching for Superior Water Oxidation

Reconstructing the surface-electronic-structure of catalysts for efficient electrocatalytic activity is crucial but still under intense exploration. Herein, we introduce a double-cation gradient etching technique to manipulate the electronic structure of perovskite LaCoO₃. With the gradient dissolution of cations, the surface was reconstructed, and the perovskite/spinel heterostructure V-LCO/Co₃O₄ (V-LCO refers to LaCoO₃ with La and Co vacancies) can be realized. Its surface-electronic-structure is effectively regulated due to the heterogeneous interface effect and abundant vacancies, resulting in a significantly enhanced activity for oxygen evolution reaction (OER). The V-LCO/Co₃O₄ exhibits low electrochemical activation energy and 2 orders of magnitude higher carrier concentrations (1.36 × 10²¹ cm^-3) compared with LCO (6.03 × 10¹⁹ cm^-3). Density functional theory (DFT) calculation unveils that the directional reconstruction of surface-electronic-structure enables the d-band center of V-LCO/Co₃O₄ to a moderate position, endowing perfect adsorption strength for oxo groups and thus promoting the electrocatalytic activity.

Defect engineering of oxide perovskites for catalysis and energy storage: synthesis of chemistry and materials science

Oxide perovskites have emerged as an important class of materials with important applications in many technological areas, particularly thermocatalysis, electrocatalysis, photocatalysis, and energy storage. However, their implementation faces numerous challenges that are familiar to the chemist and materials scientist. The present work surveys the state-of-the-art by integrating these two viewpoints, focusing on the critical role that defect engineering plays in the design, fabrication, modification, and application of these materials. An extensive review of experimental and simulation studies of the synthesis and performance of oxide perovskites and devices containing these materials is coupled with exposition of the fundamental and applied aspects of defect equilibria. The aim of this approach is to elucidate how these issues can be integrated in order to shed light on the interpretation of the data and what trajectories are suggested by them. This critical examination has revealed a number of areas in which the review can provide a greater understanding. These include considerations of (1) the nature and formation of solid solutions, (2) site filling and stoichiometry, (3) the rationale for the design of defective oxide perovskites, and (4) the complex mechanisms of charge compensation and charge transfer. The review concludes with some proposed strategies to address the challenges in the future development of oxide perovskites and their applications.

Recent advances in activating surface reconstruction for the high-efficiency oxygen evolution reaction

A climax in the development of cost-effective and high-efficiency transition metal-based electrocatalysts has been witnessed recently for sustainable energy and related conversion technologies. In this regard, structure-activity relationships based on several descriptors have already been proposed to rationally design electrocatalysts. However, the dynamic reconstruction of the surface structures and compositions of catalysts during electrocatalytic water oxidation, especially during the anodic oxygen evolution reaction (OER), complicate the streamlined prediction of the catalytic activity. With the achievements in operando and in situ techniques, it has been found that electrocatalysts undergo surface reconstruction to form the actual active species in situ accompanied with an increase in their oxidation state during OER in alkaline solution. Accordingly, a thorough understanding of the surface reconstruction process plays a critical role in establishing unambiguous structure-composition-property relationships in pursuit of high-efficiency electrocatalysts. However, several issues still need to be explored before high electrocatalytic activities can be realized, as follows: (1) the identification of initiators and pathways for surface reconstruction, (2) establishing the relationships between structure, composition, and electrocatalytic activity, and (3) the rational manipulation of in situ catalyst surface reconstruction. In this review, the recent progress in the surface reconstruction of transition metal-based OER catalysts including oxides, non-oxides, hydroxides and alloys is summarized, emphasizing the fundamental understanding of reconstruction behavior from the original precatalysts to the actual catalysts based on operando analysis and theoretical calculations. The state-of-the-art strategies to tailor the surface reconstruction such as substituting/doping with metals, introducing anions, incorporating oxygen vacancies, tuning morphologies and exploiting plasmonic/thermal/photothermal effects are then introduced. Notably, comprehensive operando/in situ characterization together with computational calculations are responsible for unveiling the improvement mechanism for OER. By delivering the progress, strategies, insights, techniques, and perspectives, this review will provide a comprehensive understanding of the surface reconstruction in transition metal-based OER catalysts and future guidelines for their rational development.

Oxygen-deficient perovskites for oxygen evolution reaction in alkaline media: a review

Oxygen vacancies in complex metal oxides and specifically in perovskites are demonstrated to significantly enhance their electrocatalytic activities due to facilitating a degree of control in the material’s intrinsic properties. The reported enhancement in intrinsic OER activity of oxygen-deficient perovskites surfaces has inspired their fabrication via a myriad of schemes. Oxygen vacancies in perovskites are amongst the most favorable anionic or Schottky defects to be induced due to their low formation energies. This review discusses recent efforts for inducing oxygen vacancies in a multitude of perovskites, including facile and environmentally benign synthesis strategies, characterization techniques, and detailed insight into the intrinsic mechanistic modulation of perovskite electrocatalysts. Experimental, analytical, and computational techniques dedicated to the understanding of the improvement of OER activities upon oxygen vacancy induction are summarized in this work. The identification and utilization of intrinsic activity descriptors for the modulation of configurational structure, improvement in bulk charge transport, and favorable inflection of the electronic structure are also discussed. It is our foresight that the approaches, challenges, and prospects discussed herein will aid researchers in rationally designing highly active and stable perovskites that can outperform noble metal-based OER electrocatalysts.

Infiltrated Ba0.5Sr0.5Co0.8Fe0.2O3-δ-Based Electrodes as Anodes in Solid Oxide Electrolysis Cells

In the last decades, several works have been carried out on solid oxide fuel cell (SOFC) and solid oxide electrolysis cell (SOEC) technologies, as they are powerful and efficient devices for energy conversion and electrochemical storage. By increasing use of renewable sources, a discontinuous amount of electricity is indeed released, and reliable storage systems represent the key feature in such a future energy scenario. In this context, systems based on reversible solid oxide cells (rSOCs) are gaining increasing attention. An rSOC is an electrochemical device that can operate sequentially between discharging (SOFC mode) and charging (SOEC mode); then, it is essential the electrodes are able to guarantee high catalytic activity, both in oxidation and reduction conditions. Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF) has been widely recognized as one of the most promising electrode catalysts for the oxygen reduction reaction (ORR) in SOFC technology because of its astonishing content of oxygen vacancies, even at room temperature. The purpose of this study is the development of BSCF to be used as anode material in electrolysis mode, maintaining enhanced energy and power density. Impregnation with a La0.8Sr0.2MnO3 (LSM) discrete nanolayer is applied to pursue structural stability, resulting in a long lifetime reliability. Impedance spectroscopy measurements under anodic overpotential conditions are run to test BSCF and LSM-BSCF activity as the electrode in oxidation mode. The observed results suggest that BSCF is a very promising candidate as an oxygen electrode in rSOC systems.