Nanostructure Tuning of Gold Nanoparticles Films via Click Sintering

Colloidal metal nanoparticles dispersions are commonly used to create functional printed electronic devices and they typically require time-, energy- and equipment-consuming post-treatments to improve their electrical and mechanical properties. Traditional methods, e.g. thermal, UV/IR, and microwave treatments, limit the substrate options and may require expensive equipment, not available in all the laboratories. Moreover, these processes also cause the collapse of the film (nano)pores and interstices, limiting or impeding its nanostructuration. Finding a simple approach to obtain complex nanostructured materials with minimal post-treatments remains a challenge. In this study, a new sintering method for gold nanoparticle inks that called as "click sintering" has been reported. The method uses a catalytic reaction to enhance and tune the nanostructuration of the film while sintering the metallic nanoparticles, without requiring any cumbersome post-treatment. This results in a conductive and electroactive nanoporous thin film, whose properties can be tuned by the conditions of the reaction, i.e., concentration of the reagent and time. Therefore, this study presents a novel and innovative one-step approach to simultaneously sinter gold nanoparticles films and create functional nanostructures, directly and easily, introducing a new concept of real-time treatment with possible applications in the fields of flexible electronics, biosensing, energy, and catalysis.

An amperometric biosensor of L-fucose in urine for the first screening test of cancer

Quantitative routine detection of fucose, which is a cancer marker, in urine is effective for the preliminary screening of cancer. Amperometric biosensing methods have the advantage of being simple, rapid, and precise for urinalysis. However, coexisting electroactive interferences such as ascorbic acid (AA), dopamine (DA), and uric acid (UA) prevent accurate measurements. In this work, an amperometric l-fucose biosensor unaffected by interferences was developed and utilizes direct electron transfer type bioelectrocatalysis of pyrroloquinoline quinone (PQQ)-dependent pyranose dehydrogenase from Coprinopsis cinerea (CcPDH). The isolated PQQ domain from CcPDH was immobilized on gold nanoparticle (AuNP)-modified electrodes, which obtained a catalytic current at a lower potential than the oxidation potential of the interfering compounds. Applying an operating potential of -0.1 V vs. Ag|AgCl (3 M NaCl) enabled the detection of l-fucose while completely eliminating the oxidation of AA, DA, and UA on the electrodes. The increase in the specific area of the electrodes by increasing the AuNP drop-casting time resulted in an improvement in the sensor performance. The biosensor exhibited a linear range for l-fucose detection between 0.1 mM and 1 mM (R² = 0.9996), including a cut-off value, the sensitivity was 3.12 ± 0.05 μA mM^-1 cm^-2, and the detection limit was 13.6 μM at a signal-to-noise ratio of three. The biosensor can be used to quantify the concentration of l-fucose at physiological levels and does not require urine preprocessing, making it applicable to practical use for point-of-care testing with urine.

Electrochemical properties of the interaction between cytochrome c and a hematite nanowire array electrode

We investigate the interaction of horse heart cytochrome c (cyt c) with hematite nanowire array electrodes by cyclic voltammetry to study the electron transfer between redox active proteins and mineral surfaces. Using this model system, we quantify electron transfer rates between cyt c and hematite under varying electric potential and pH conditions. The results are consistent with two cyt c conformations adsorbed at the hematite surface: the native and a partially unfolded form. The partially unfolded protein maintained redox activity, but at a lower redox potential than the native protein. Adsorption of cyt c allowed direct electron transfer between cyt c and hematite, with an interfacial electron transfer rate, k°_ET, of 0.4 s^-1 for the native form and 0.55 s^-1 for the partially unfolded protein at pH 7.07. At pH 4.66, protein adsorption decreased compared to neutral pH and the fraction of partially unfolded protein increased. Additionally, the diffusion controlled electron transfer rate between hematite and the electron shuttling compound anthraquinone-2,6-disulfonate (AQDS) was determined to be k°_ET = 8.0·10^-3 cm·s^-1 at pH 7.07. Modulation of electron transfer rates as a result of conformational changes by redox active proteins has broad implications for describing chemical transformations at biological-mineral interfaces.

Pore and ligament size control, thermal stability and mechanical properties of nanoporous single crystals of gold

Nanoporous gold is widely used in research and nanotechnology because of its diverse properties, including high surface area and catalytic activity. The ligament size is usually considered as one of the main parameters controlling thermal stability and mechanical properties of nanoporous gold. Recently we developed a method for creating nanoporous single crystal gold particles using eutectic decomposition of Au-Ge, followed by selective etching of Ge. Here, we used this novel method to create nanoporous gold particles with controlled ligament sizes by changing the initial sample's relative concentrations of gold and germanium. When investigated over 1-4 h at 250-400 °C the material was thermally stable up to 350 °C, which is higher than the thermal stability of "classical" nanoporous gold prepared by dealloying. Mechanical properties were examined utilizing nanoindentation of nanoporous gold before and after annealing. For smaller ligament sizes, hardness increased with annealing temperature up to 300 °C and then strongly decreased. For larger ligament sizes, hardness decreased with increasing annealing temperature. Young's modulus was unchanged up to 300 °C.

A Third Generation Glucose Biosensor Based on Cellobiose Dehydrogenase Immobilized on a Glassy Carbon Electrode Decorated with Electrodeposited Gold Nanoparticles: Characterization and Application in Human Saliva

Efficient direct electron transfer (DET) between a cellobiose dehydrogenase mutant from Corynascus thermophilus (CtCDH C291Y) and a novel glassy carbon (GC)-modified electrode, obtained by direct electrodeposition of gold nanoparticles (AuNPs) was realized. The electrode was further modified with a mixed self-assembled monolayer of 4-aminothiophenol (4-APh) and 4-mercaptobenzoic acid (4-MBA), by using glutaraldehyde (GA) as cross-linking agent. The CtCDH C291Y/GA/4-APh,4-MBA/AuNPs/GC platform showed an apparent heterogeneous electron transfer rate constant (ks) of 19.4 ± 0.6 s-1, with an enhanced theoretical and real enzyme surface coverage (Γtheor and Γreal) of 5287 ± 152 pmol cm-2 and 27 ± 2 pmol cm-2, respectively. The modified electrode was successively used as glucose biosensor exhibiting a detection limit of 6.2 μM, an extended linear range from 0.02 to 30 mM, a sensitivity of 3.1 ± 0.1 μA mM-1 cm-2 (R2 = 0.995), excellent stability and good selectivity. These performances compared favourably with other glucose biosensors reported in the literature. Finally, the biosensor was tested to quantify the glucose content in human saliva samples with successful results in terms of both recovery and correlation with glucose blood levels, allowing further considerations on the development of non-invasive glucose monitoring devices.

Electrochemical Detecting Lung Cancer-Associated Antigen Based on Graphene-Gold Nanocomposite

Using a Au nanoparticle/reduced graphene oxide composite (AuNP-RGO), a signal-enhanced electrochemical immunosensor without label was created to detect neuron-specific enolase (NSE). Furthermore, an environmentally-friendly method was developed to prepare AuNP-RGO by employing chitosan (CS), which served as reducing and stabilizing agent. We showed that the sensitivity of the immunosensor designed in this report was remarkably enhanced because of the numerous active sites in the sensor provided by the AuNP-RGO nanostructure. For the quantification of NSE, the immunosensor exhibited a positive linear relationship with the concentration in the range of 0.1 to 2000 ng/mL, where the limit of the detection was 0.05 ng/mL.

Fully Enzymatic Membraneless Glucose|Oxygen Fuel Cell That Provides 0.275 mA cm(-2) in 5 mM Glucose, Operates in Human Physiological Solutions, and Powers Transmission of Sensing Data

Coimmobilization of pyranose dehydrogenase as an enzyme catalyst, osmium redox polymers [Os(4,4'-dimethoxy-2,2'-bipyridine)2(poly(vinylimidazole))10Cl](+) or [Os(4,4'-dimethyl-2,2'-bipyridine)2(poly(vinylimidazole))10Cl](+) as mediators, and carbon nanotube conductive scaffolds in films on graphite electrodes provides enzyme electrodes for glucose oxidation. The recombinant enzyme and a deglycosylated form, both expressed in Pichia pastoris, are investigated and compared as biocatalysts for glucose oxidation using flow injection amperometry and voltammetry. In the presence of 5 mM glucose in phosphate-buffered saline (PBS) (50 mM phosphate buffer solution, pH 7.4, with 150 mM NaCl), higher glucose oxidation current densities, 0.41 mA cm(-2), are obtained from enzyme electrodes containing the deglycosylated form of the enzyme. The optimized glucose-oxidizing anode, prepared using deglycosylated enzyme coimmobilized with [Os(4,4'-dimethyl-2,2'-bipyridine)2(poly(vinylimidazole))10Cl](+) and carbon nanotubes, was coupled with an oxygen-reducing bilirubin oxidase on gold nanoparticle dispersed on gold electrode as a biocathode to provide a membraneless fully enzymatic fuel cell. A maximum power density of 275 μW cm(-2) is obtained in 5 mM glucose in PBS, the highest to date under these conditions, providing sufficient power to enable wireless transmission of a signal to a data logger. When tested in whole human blood and unstimulated human saliva maximum power densities of 73 and 6 μW cm(-2) are obtained for the same fuel cell configuration, respectively.

Biomimetic environment to study E. coli complex I through surface-enhanced IR absorption spectroscopy

In this study complex I was immobilized in a biomimetic environment on a gold layer deposited on an ATR-crystal in order to functionally probe the enzyme against substrates and inhibitors via surface-enhanced IR absorption spectroscopy (SEIRAS) and cyclic voltammetry (CV). To achieve this immobilization, two methods based on the generation of a high affinity self-assembled monolayer (SAM) were probed. The first made use of the affinity of Ni-NTA toward a hexahistidine tag that was genetically engineered onto complex I and the second exploited the affinity of the enzyme toward its natural substrate NADH. Experiments were also performed with complex I reconstituted in lipids. Both approaches have been found to be successful, and electrochemically induced IR difference spectra of complex I were obtained.

Evidence for distinct electron transfer processes in terminal oxidases from different origin by means of protein film voltammetry

Cytochrome aa₃ from Paracoccus denitrificans and cytochrome ba₃ from Thermus thermophilus, two distinct members of the heme–copper oxidase superfamily, were immobilized on electrodes modified with gold nanoparticles. This procedure allowed us to achieve direct electron transfer between the enzyme and the gold nanoparticles and to obtain evidence for different electrocatalytic properties of the two enzymes. The pH dependence and thermostability reveal that the enzymes are highly adapted to their native environments. These results suggest that evolution resulted in different solutions to the common problem of electron transfer to oxygen.

Biofuel cell based on microscale nanostructured electrodes with inductive coupling to rat brain neurons

Miniature, self-contained biodevices powered by biofuel cells may enable a new generation of implantable, wireless, minimally invasive neural interfaces for neurophysiological in vivo studies and for clinical applications. Here we report on the fabrication of a direct electron transfer based glucose/oxygen enzymatic fuel cell (EFC) from genuinely three-dimensional (3D) nanostructured microscale gold electrodes, modified with suitable biocatalysts. We show that the process underlying the simple fabrication method of 3D nanostructured electrodes is based on an electrochemically driven transformation of physically deposited gold nanoparticles. We experimentally demonstrate that mediator-, cofactor-, and membrane-less EFCs do operate in cerebrospinal fluid and in the brain of a rat, producing amounts of electrical power sufficient to drive a self-contained biodevice, viz. 7 μW cm⁻²in vitro and 2 μW cm⁻²in vivo at an operating voltage of 0.4 V. Last but not least, we also demonstrate an inductive coupling between 3D nanobioelectrodes and living neurons.

Cellobiose dehydrogenase modified electrodes: advances by materials science and biochemical engineering

The flavocytochrome cellobiose dehydrogenase (CDH) is a versatile biorecognition element capable of detecting carbohydrates as well as quinones and catecholamines. In addition, it can be used as an anode biocatalyst for enzymatic biofuel cells to power miniaturised sensor-transmitter systems. Various electrode materials and designs have been tested in the past decade to utilize and enhance the direct electron transfer (DET) from the enzyme to the electrode. Additionally, mediated electron transfer (MET) approaches via soluble redox mediators and redox polymers have been pursued. Biosensors for cellobiose, lactose and glucose determination are based on CDH from different fungal producers, which show differences with respect to substrate specificity, pH optima, DET efficiency and surface binding affinity. Biosensors for the detection of quinones and catecholamines can use carbohydrates for analyte regeneration and signal amplification. This review discusses different approaches to enhance the sensitivity and selectivity of CDH-based biosensors, which focus on (1) more efficient DET on chemically modified or nanostructured electrodes, (2) the synthesis of custom-made redox polymers for higher MET currents and (3) the engineering of enzymes and reaction pathways. Combination of these strategies will enable the design of sensitive and selective CDH-based biosensors with reduced electrode size for the detection of analytes in continuous on-site and point-of-care applications.

Nanoporous Gold Electrodes and Their Applications in Analytical Chemistry

Nanoporous gold prepared by dealloying Au:Ag alloys has recently become an attractive material in the field of analytical chemistry. This conductive material has an open, 3D porous framework consisting of nanosized pores and ligaments with surface areas that are 10s to 100s of times larger than planar gold of an equivalent geometric area. The high surface area coupled with an open pore network makes nanoporous gold an ideal support for the development of chemical sensors. Important attributes include conductivity, high surface area, ease of preparation and modification, tunable pore size, and a bicontinuous open pore network. In this paper, the fabrication, characterization, and applications of nanoporous gold in chemical sensing are reviewed specifically as they relate to the development of immunosensors, enzyme-based biosensors, DNA sensors, Raman sensors, and small molecule sensors.

Direct Electrochemistry of Cytochrome bo Oxidase at a series of Gold Nanoparticles-Modified Electrodes

New membrane-protein based electrodes were prepared incorporating cytochrome bo(3) from E. coli and gold nanoparticles. Direct electron transfer between the electrode and the immobilized enzymes was achieved, resulting in an electrocatalytic activity in presence of O(2). The size of the gold nanoparticles was shown to be important and smaller particles were shown to reduce the overpotential of the process.

Direct electrochemistry of Phanerochaete chrysosporium cellobiose dehydrogenase covalently attached onto gold nanoparticle modified solid gold electrodes

Achieving efficient electrochemical communication between redox enzymes and various electrode materials is one of the main challenges in bioelectrochemistry and is of great importance for developing electronic applications. Cellobiose dehydrogenase (CDH) is an extracellular flavocytochrome composed of a catalytic FAD containing dehydrogenase domain (DH(CDH)), a heme b containing cytochrome domain (CYT(CDH)), and a flexible linker region connecting the two domains. Efficient direct electron transfer (DET) of CDH from the basidiomycete Phanerochaete chrysosporium (PcCDH) covalently attached to mixed self-assembled monolayer (SAM) modified gold nanoparticle (AuNP) electrode is presented. The thiols used were as follows: 4-aminothiophenol (4-ATP), 4-mercaptobenzoic acid (4-MBA), 4-mercaptophenol (4-MP), 11-mercapto-1-undecanamine (MUNH(2)), 11-mercapto-1-undecanoic acid (MUCOOH), and 11-mercapto-1-undecanol (MUOH). A covalent linkage between PcCDH and 4-ATP or MUNH(2) in the mixed SAMs was formed using glutaraldehyde as cross-linker. The covalent immobilization and the surface coverage of PcCDH were confirmed with surface plasmon resonance (SPR). To improve current density, AuNPs were cast on the top of polycrystalline gold electrodes. For all the immobilized PcCDH modified AuNPs electrodes, cyclic voltammetry exhibited clear electrochemical responses of the CYT(CDH) with fast electron transfer (ET) rates in the absence of substrate (lactose), and the formal potential was evaluated to be +162 mV vs NHE at pH 4.50. The standard ET rate constant (k(s)) was estimated for the first time for CDH and was found to be 52.1, 59.8, 112, and 154 s(-1) for 4-ATP/4-MBA, 4-ATP/4-MP, MUNH(2)/MUCOOH, and MUNH(2)/MUOH modified electrodes, respectively. At all the mixed SAM modified AuNP electrodes, PcCDH showed DET only via the CYT(CDH). No DET communication between the DH(CDH) domain and the electrode was found. The current density for lactose oxidation was remarkably increased by introduction of the AuNPs. The 4-ATP/4-MBA modified AuNPs exhibited a current density up to 30 μA cm(-2), which is ∼70 times higher than that obtained for a 4-ATP/4-MBA modified polycrystalline gold electrode. The results provide insight into fundamental electrochemical properties of CDH covalently immobilized on gold electrodes and promote further applications of CDHs for biosensors, biofuel cells, and bioelectrocatalysis.

Long Distance Electron Transfer Across >100 nm Thick Au Nanoparticle/Polyion Films to a Surface Redox Protein

Glutathione-decorated 5 nm gold nanoparticles (AuNPs) and oppositely charged poly(allylamine hydrochloride) (PAH) were assembled into {PAH/AuNP} n films fabricated layer-by-layer (LbL) on pyrolytic graphite (PG) electrodes. These AuNP/polyion films utilized the AuNPs as electron hopping relays to achieve direct electron transfer between underlying electrodes and redox proteins on the outer film surface across unprecedented distances >100 nm for the first time. As film thickness increased, voltammetric peak currents for surface myoglobin (Mb) on these films decreased but the electron transfer rate was relatively constant, consistent with a AuNP-mediated electron hopping mechanism.