Determining relevance of a weight-bearing ovine model for bone ingrowth assessment

Effect of Press-Fit Size on Insertion Mechanics and Cartilage Viability in Human and Ovine Osteochondral Grafts

OBJECTIVE

The osteochondral allograft procedure uses grafts constructed larger than the recipient site to stabilize the graft, in what is known as the press-fit technique. This research aims to characterize the relationships between press-fit size, insertion forces, and cell viability in ovine and human osteochondral tissue.

DESIGN

Human (4 donors) and ovine (5 animals) articular joints were used to harvest osteochondral grafts (4.55 mm diameter, N = 33 Human, N = 35 Ovine) and create recipient sites with grafts constructed to achieve varying degrees of press fit (0.025-0.240 mm). Donor grafts were inserted into recipient sites while insertion forces were measured followed by quantification of chondrocyte viability and histological staining to evaluate the extracellular matrix.

RESULTS

Both human and ovine tissues exhibited similar mechanical and cellular responses to changes in press-fit. Insertion forces (Human: 3-169 MPa, Ovine: 36-314 MPa) and cell viability (Human: 16%-89% live, Ovine: 2%-76% live) were correlated to press-fit size for both human (force: r = 0.539, viability: r = -0.729) and ovine (force: r = 0.655, viability: r = -0.714) tissues. In both species, a press-fit above 0.14 mm resulted in reduced cell viability below a level acceptable for transplantation, increased insertion forces, and reduced linear correlation to press-fit size compared to samples with a press-fit below 0.14 mm.

CONCLUSIONS

Increasing press-fit size required increased insertion forces and resulted in reduced cell viability. Ovine and human osteochondral tissues responded similarly to impact insertion and varying press-fit size, providing evidence for the use of the ovine model in allograft-related research.

Determining Which Combinatorial Combat-Relevant Factors Contribute to Heterotopic Ossification Formation in an Ovine Model

Traumatic heterotopic ossification (HO) is frequently observed in Service Members following combat-related trauma. Estimates suggest that ~65% of wounded warriors who suffer limb loss or major extremity trauma will experience some type of HO formation. The development of HO delays rehabilitation and can prevent the use of a prosthetic. To date there are limited data to suggest a standard mechanism for preventing HO. This may be due to inadequate animal models not producing a similar bone structure as human HO. We recently showed that traumatic HO growth is possible in an ovine model. Within that study, we demonstrated that 65% of sheep developed a human-relevant hybrid traumatic HO bone structure after being exposed to a combination of seven combat-relevant factors. Although HO formed, we did not determine which traumatic factor contributed most. Therefore, in this study, we performed individual and various combinations of surgical/traumatic factors to determine their individual contribution to HO growth. Outcomes showed that the presence of mature biofilm stimulated a large region of bone growth, while bone trauma resulted in a localized bone response as indicated by jagged bone at the linea aspera. However, it was not until the combinatory factors were included that an HO structure similar to that of humans formed more readily in 60% of the sheep. In conclusion, data suggested that traumatic HO growth can develop following various traumatic factors, but a combination of known instigators yields higher frequency size and consistency of ectopic bone.

Keratin-containing scaffolds for tissue engineering applications: a review

In tissue engineering and regenerative medicine applications, the utilization of bioactive materials has become a routine tool. The goal of tissue engineering is to create new organs and tissues by combining cell biology, materials science, reactor engineering, and clinical research. As part of the growth pattern for primary cells in an organ, backing material is frequently used as a supporting material. A porous three-dimensional (3D) scaffold can provide cells with optimal conditions for proliferating, migrating, differentiating, and functioning as a framework. Optimizing the scaffolds' structure and altering their surface may improve cell adhesion and proliferation. A keratin-based biomaterials platform has been developed as a result of discoveries made over the past century in the extraction, purification, and characterization of keratin proteins from hair and wool fibers. Biocompatibility, biodegradability, intrinsic biological activity, and cellular binding motifs make keratin an attractive biomaterial for tissue engineering scaffolds. Scaffolds for tissue engineering have been developed from extracted keratin proteins because of their capacity to self-assemble and polymerize into intricate 3D structures. In this review article, applications of keratin-based scaffolds in different tissues including bone, skin, nerve, and vascular are explained based on common methods of fabrication such as electrospinning, freeze-drying process, and sponge replication method.

Association between blood markers and the progression of osseointegration in percutaneous prostheses patients-A pilot study

Patients implanted with osseointegrated (OI) prosthetic systems have reported vastly improved upper and lower extremity prosthetic function compared with their previous experience with socket-suspension systems. However, OI systems have been associated with superficial and deep-bone infections and implant loosening due, in part, to a failure of the osseointegration process. Although monitoring the osseointegration using circulating biomarkers has clinical relevance for understanding the progression of osseointegration with these devices, it has yet to be established. Ten patients were enrolled in this study. Blood samples were collected at pre-selected times, starting before implantation surgery, and continuing to 12 months after the second surgery. Bone formation markers, bone resorption markers, and circulating amino acids were measured from blood samples. A linear mixed model was generated for each marker, incorporating patient ID and age with the normalized marker value as the response variable. Post hoc comparisons were made between 1 week before Stage 1 Surgery and all subsequent time points for each marker, followed by multiple testing corrections. Serial radiographic imaging of the residual limb containing the implant was obtained during follow-up, and the cortical index (CI) was calculated for the bone at the porous region of the device. Two markers of bone formation, specifically bone-specific alkaline phosphatase (Bone-ALP) and amino-terminal propeptide of type I procollagen (PINP), exhibited significant increases when compared with the baseline levels of unloaded residual bone prior to the initial surgery, and they subsequently returned to their baseline levels by the 12-month mark. Patients who experienced clinically robust osseointegration experienced increased cortical bone thickness at the porous coated region of the device. A medium correlation was observed between Bone-ALP and the porous CI values up to PoS2-M1 (p = .056), while no correlation was observed for PINP. An increase in bone formation markers and the lack of change observed in bone resorption markers likely reflect increased cortical bone formation induced by the end-loading design of the Utah OI device used in this study. A more extensive study is required to validate the correlation observed between Bone-ALP and porous CI values.

Long-Bone-Regeneration Process in a Sheep Animal Model, Using Hydroxyapatite Ceramics Prepared by Tape-Casting Method

This study was designed to investigate the effects of hydroxyapatite (HA) ceramic implants (HA cylinders, perforated HA plates, and nonperforated HA plates) on the healing of bone defects, addressing biocompatibility, biodegradability, osteoconductivity, osteoinductivity, and osteointegration with the surrounding bone tissue. The HA ceramic implants were prepared using the tape-casting method, which allows for shape variation in samples after packing HA paste into 3D-printed plastic forms. In vitro, the distribution and morphology of the MC3T3E1 cells grown on the test discs for 2 and 9 days were visualised with a fluorescent live/dead staining assay. The growth of the cell population was clearly visible on the entire ceramic surfaces and very good osteoblastic cell adhesion and proliferation was observed, with no dead cells detected. A sheep animal model was used to perform in vivo experiments with bone defects created on the metatarsal bones, where histological and immunohistochemical tissue analysis as well as X-ray and CT images were applied. After 6 months, all implants showed excellent biocompatibility with the surrounding bone tissue with no observed signs of inflammatory reaction. The histomorphological findings revealed bone growth immediately over and around the implants, indicating the excellent osteoconductivity of the HA ceramic implants. A number of islands of bone tissue were observed towards the centres of the HA cylinders. The highest degree of biodegradation, bioresorption, and new bone formation was observed in the group in which perforated HA plates were applied. The results of this study suggest that HA cylinders and HA plates may provide a promising material for the functional long-bone-defect reconstruction and further research.

Expression of the pleiotrophin-midkine axis in a sheep tooth socket model of bone healing

OBJECTIVE AND BACKGROUND

Resorption of alveolar bone after tooth extraction is a common problem often requiring bone grafting. The success of the grafting procedures is dependent on multiple factors including the presence of growth factors. This is the first in vivo study to investigate the role of the pleiotrophin family of cytokines in alveolar bone regeneration. This research investigated the role of the pleiotrophin-midkine (PTN-MDK) axis during osteogenesis, with and without a grafting material, after tooth extraction in a sheep model.

METHODS

Thirty Romney-cross ewes were anesthetized, and all premolar teeth on the right side were extracted. The sockets were randomized to controls sites with no treatment and test sites with Bio-Oss® graft material and Bio-Gide® membrane. Samples were harvested after sacrificing animals 4, 8, and 16 weeks post-grafting (n = 10 per time-point). Tissue for qRT² -PCR gene analysis was recovered from the socket next to the first molar using a trephine (Ø = 2 mm). Each socket was fixed, decalcified, paraffin-embedded, and sectioned. Immunohistochemistry was conducted to localize both PTN and MDK along with their receptors, protein tyrosine phosphatase receptor type Z1 (PTPRZ1), ALK receptor tyrosine kinase (ALK), and notch receptor 2 (NOTCH2).

RESULTS

Within the healing sockets, high expression of genes for PTN, MDK, NOTCH2, and ALK was found at all time-points and in both grafted and non-grafted sites, while PTPRZ1 was only expressed at low levels. The relative gene expression of the PTN family of cytokines was not statistically different at the three time-points between test and control groups (p > .05). Immunohistochemistry found PTN and MDK in association with new bone, NOTCH2 in the connective tissue, and PTPRZ1 and ALK in association with cuboidal osteoblasts involved in bone formation.

CONCLUSIONS

The PTN-MDK axis was highly expressed in both non-grafted and grafted sockets during osteogenesis in a sheep model of alveolar bone regeneration with no evidence that grafting significantly affected expression. The activation of NOTCH2 and PTPRZ1 receptors may be important during bone regeneration in vivo. The discovery of the PTN-MDK axis as important during alveolar bone regeneration is novel and opens up new avenues of research into these stably expressed highly active cytokines. Growth factor supplementation with PTN and/or MDK during healing may be an approach for enhanced regeneration or to initiate healing where delayed.

A Novel Nanostructured Surface on Titanium Implants Increases Osseointegration in a Sheep Model

BACKGROUND

A nanostructured titanium surface that promotes antimicrobial activity and osseointegration would provide the opportunity to create medical implants that can prevent orthopaedic infection and improve bone integration. Although nanostructured surfaces can exhibit antimicrobial activity, it is not known whether these surfaces are safe and conducive to osseointegration.

QUESTIONS/PURPOSES

Using a sheep animal model, we sought to determine whether the bony integration of medical-grade, titanium, porous-coated implants with a unique nanostructured surface modification (alkaline heat treatment [AHT]) previously shown to kill bacteria was better than that for a clinically accepted control surface of porous-coated titanium covered with hydroxyapatite (PCHA) after 12 weeks in vivo. The null hypothesis was that there would be no difference between implants with respect to the primary outcomes: interfacial shear strength and percent intersection surface (the percentage of implant surface with bone contact, as defined by a micro-CT protocol), and the secondary outcomes: stiffness, peak load, energy to failure, and micro-CT (bone volume/total volume [BV/TV], trabecular thickness [Tb.Th], and trabecular number [Tb.N]) and histomorphometric (bone-implant contact [BIC]) parameters.

METHODS

Implants of each material (alkaline heat-treated and hydroxyapatite-coated titanium) were surgically inserted into femoral and tibial metaphyseal cancellous bone (16 per implant type; interference fit) and in tibial cortices at three diaphyseal locations (24 per implant type; line-to-line fit) in eight skeletally mature sheep. At 12 weeks postoperatively, bones were excised to assess osseointegration of AHT and PCHA implants via biomechanical push-through tests, micro-CT, and histomorphometry. Bone composition and remodeling patterns in adult sheep are similar to that of humans, and this model enables comparison of implants with ex vivo outcomes that are not permissible with humans. Comparisons of primary and secondary outcomes were undertaken with linear mixed-effects models that were developed for the cortical and cancellous groups separately and that included a random effect of animals, covariates to adjust for preoperative bodyweight, and implant location (left/right limb, femoral/tibial cancellous, cortical diaphyseal region, and medial/lateral cortex) as appropriate. Significance was set at an alpha of 0.05.

RESULTS

The estimated marginal mean interfacial shear strength for cancellous bone, adjusted for covariates, was 1.6 MPa greater for AHT implants (9.3 MPa) than for PCHA implants (7.7 MPa) (95% CI 0.5 to 2.8; p = 0.006). Similarly, the estimated marginal mean interfacial shear strength for cortical bone, adjusted for covariates, was 6.6 MPa greater for AHT implants (25.5 MPa) than for PCHA implants (18.9 MPa) (95% CI 5.0 to 8.1; p < 0.001). No difference in the implant-bone percent intersection surface was detected for cancellous sites (cancellous AHT 55.1% and PCHA 58.7%; adjusted difference of estimated marginal mean -3.6% [95% CI -8.1% to 0.9%]; p = 0.11). In cortical bone, the estimated marginal mean percent intersection surface at the medial site, adjusted for covariates, was 11.8% higher for AHT implants (58.1%) than for PCHA (46.2% [95% CI 7.1% to 16.6%]; p < 0.001) and was not different at the lateral site (AHT 75.8% and PCHA 74.9%; adjusted difference of estimated marginal mean 0.9% [95% CI -3.8% to 5.7%]; p = 0.70).

CONCLUSION

These data suggest there is stronger integration of bone on the AHT surface than on the PCHA surface at 12 weeks postimplantation in this sheep model.

CLINICAL RELEVANCE

Given that the AHT implants formed a more robust interface with cortical and cancellous bone than the PCHA implants, a clinical noninferiority study using hip stems with identical geometries can now be performed to compare the same surfaces used in this study. The results of this preclinical study provide an ethical baseline to proceed with such a clinical study given the potential of the alkaline heat-treated surface to reduce periprosthetic joint infection and enhance implant osseointegration.

Irregular porous titanium enhances implant stability and bone ingrowth in an intra-articular ovine model

Two commercially available porous coatings, Gription and Porocoat, were compared for the first time in a challenging intra-articular, weight-bearing, ovine model. Gription has evolved from Porocoat and has higher porosity, coefficient of friction, and microtextured topography, which are expected to enhance bone ingrowth. Cylindrical implants were press-fit into the weight-bearing regions of ovine femoral condyles and bone ingrowth and fixation strength evaluated 4, 8, and 16 weeks postoperatively. Biomechanical push-out tests were performed on lateral femoral condyles (LFCs) to evaluate the strength of the bone-implant interface. Bone ingrowth was assessed in medial femoral condyles (MFCs) as well as implants retrieved from LFCs following biomechanical testing using backscattered electron microscopy and histology. By 16 weeks, Gription-coated implants exhibited higher force (2455 ± 1362 vs. 1002 ± 1466 N; p = 0.046) and stress (12.60 ± 6.99 vs. 5.14 ± 7.53 MPa; p = 0.046) at failure, and trended towards higher stiffness (11,510 ± 7645 vs. 5010 ± 8374 N/mm; p = 0.061) and modulus of elasticity (591 ± 392 vs. 256 ± 431 MPa; p = 0.061). A strong, positive correlation was detected between bone ingrowth in LFC implants and failure force (r = 0.93, p < 10^-13 ). By 16 weeks, bone ingrowth in Gription-coated implants in MFCs was 10.50 ± 6.31% compared to 5.88 ± 2.77% in Porocoat (p = 0.095). Observations of the bone-implant interface, made following push-out testing, showed more bony material consistently adhered to Gription compared to Porocoat at all three time points. Gription provided superior fixation strength and bone ingrowth by 16 weeks.

3D-printed porous Ti6Al4V scaffolds for long bone repair in animal models: a systematic review

BACKGROUND

Titanium and its alloys have been widely employed for bone tissue repair and implant manufacturing. The rapid development of three-dimensional (3D) printing technology has allowed fabrication of porous titanium scaffolds with controllable microstructures, which is considered to be an effective method for promoting rapid bone formation and decreasing bone absorption. The purpose of this systematic review was to evaluate the osteogenic potential of 3D-printed porous Ti6Al4V (Ti64) scaffold for repairing long bone defects in animal models and to investigate the influential factors that might affect its osteogenic capacity.

METHODS

Electronic literature search was conducted in the following databases: PubMed, Web of Science, and Embase up to September 2021. The SYRCLE's tool and the modified CAMARADES list were used to assess the risk of bias and methodological quality, respectively. Due to heterogeneity of the selected studies in relation to protocol and outcomes evaluated, a meta-analysis could not be performed.

RESULTS

The initial search revealed 5858 studies. Only 46 animal studies were found to be eligible based on the inclusion criteria. Rabbit was the most commonly utilized animal model. A pore size of around 500-600 µm and porosity of 60-70% were found to be the most ideal parameters for designing the Ti64 scaffold, where both dodecahedron and diamond pores optimally promoted osteogenesis. Histological analysis of the scaffold in a rabbit model revealed that the maximum bone area fraction reached 59.3 ± 8.1% at weeks 8-10. Based on micro-CT assessment, the maximum bone volume fraction was found to be 34.0 ± 6.0% at weeks 12.

CONCLUSIONS

Ti64 scaffold might act as a promising medium for providing sufficient mechanical support and a stable environment for new bone formation in long bone defects. Trail registration The study protocol was registered in the PROSPERO database under the number CRD42020194100.

Early bone ingrowth and segmental stability of a trussed titanium cage versus a polyether ether ketone cage in an ovine lumbar interbody fusion model

BACKGROUND CONTEXT

Lumbar interbody fusion is an effective treatment for unstable spinal segments. However, the time needed to establish a solid bony interbody fusion between the two vertebrae may be longer than twelve months after surgery. During this time window, the instrumented spinal segment is assumed to be at increased risk for instability related complications such as cage migration or subsidence. It is hypothesized that the design of new interbody cages that enable direct osseointegration of the cage at the vertebral endplates, without requiring full bony fusion between the two vertebral endplates, might shorten the time window that the instrumented spinal segment is susceptible to failure.

PURPOSE

To quantify the bone ingrowth and resulting segmental stability during consolidation of lumbar interbody fusion using two different cage types.

STUDY DESIGN

Preclinical ovine model.

METHODS

Seven skeletally mature sheep underwent bi-segmental lumbar interbody fusion surgery with one conventional polyether ether ketone (PEEK) cage, and one newly developed trussed titanium (TT) cage. After a postoperative time period of 13 weeks, non-destructive range of motion testing, and histologic analysis was performed. Additionally, sample specific finite element (FE) analysis was performed to predict the stability of the interbody fusion region alone.

RESULTS

Physiological movement of complete spinal motion segments did not reveal significant differences between the segments operated with PEEK and TT cages. The onset of creeping substitution within the cage seemed to be sooner for PEEK cages, which led to significantly higher bone volume over total volume (BV/TV) compared with the TT cages. TT cages showed significantly more direct bone to implant contact (BIC). Although the mean stability of the interbody fusion region alone was not statistically different between the PEEK and TT cages, the variation within the cage types illustrated an all-or-nothing response for the PEEK cages while a more gradual increase in stability was found for the TT cages.

CONCLUSIONS

Spinal segments operated with conventional PEEK cages were not different from those operated with newly developed TT cages in terms of segmental stability but did show a different mechanism of bone ingrowth and attachment. Based on the differences in development of bony fusion, we hypothesize that TT cages might facilitate increased early segmental stability by direct osseointegration of the cage at the vertebral endplates without requiring complete bony bridging through the cage.

CLINICAL SIGNIFICANCE

Interbody cage type affects the consolidation process of spinal interbody fusion. Whether different consolidation processes of spinal interbody fusion result in clinically significant differences requires further investigation.

Assessing the safety of an epiphyseal plate biopsy in a translational lamb model

The literature demonstrates that obtaining a biopsy of the physis may be beneficial for diagnostic purposes. A small biopsy of the epiphyseal plate may allow for earlier detection of certain conditions and be used to monitor the healing of diseased and/or damaged physes. However, due to the fear of a growth arrest in a growing child, biopsies are not currently performed. In this study, we investigated the effects of a biopsy of the epiphyseal plate in 3-month-old lambs. A total of 4.2 mm biopsy samples were captured in the proximal tibiae and distal femora physes. The lambs were monitored 12- and 24-week post-biopsy. Computed tomography (CT) and micro-CT scans were obtained to determine if any angular deformities occurred, while scanning electron microscope (SEM) and histological analysis were utilized to assess the bone response due to the biopsy. The contralateral limbs served as unaltered controls for direct comparison within each lamb. The data demonstrated no signs of angular deformities following a 4.2 mm biopsy of the physis. Bone growth/elongation was confirmed by CT, SEM, and fluorochrome analyses and indicated that the lambs were in fact immature and still growing at the time of the biopsy. Clinical Significance: This investigation demonstrated that a small biopsy of the epiphyseal plate can be obtained safely without the cause of growth arrest and angular deformities. The ability to precisely diagnose, treat, and/or monitor at-risk children at an earlier timepoint by way of a biopsy sample could be an important advancement in regard to researching diseased and/or damaged physes.

Developing a combat-relevant translatable large animal model of heterotopic ossification

Heterotopic ossification (HO) refers to ectopic bone formation, typically in residual limbs following trauma and injury. A review of injuries from Operation Iraqi Freedom (OIF) and Operation Enduring Freedom (OEF) indicated that approximately 70% of war wounds involved the musculoskeletal system, largely in part from the use of improvised explosive devices (IED) and rocket-propelled grenades (RPG). HO is reported to occur in approximately 63%–65% of wounded warriors from OIF and OEF. Symptomatic HO may delay rehabilitation regimens since it often requires modifications to prosthetic limb componentry and socket size. There is limited evidence indicating a mechanism for preventing HO. This may be due to inadequate models, which do not produce HO bone structure that is morphologically similar to HO samples obtained from wounded warfighters injured in theatre. We hypothesized that using a high-power blast of air (shockwave) and simulated battlefield trauma (i.e. bone damage, tourniquet, bacteria, negative pressure wound therapy) in a large animal model, HO would form and have similar morphology to ectopic bone observed in clinical samples. Initial radiographic and micro-computed tomography (CT) data demonstrated ectopic bone growth in sheep 24 weeks post-procedure. Advanced histological and backscatter electron (BSE) analyses showed that 5 out of 8 (63%) sheep produced HO with similar morphology to clinical samples. We conclude that not all ectopic bone observed by radiograph or micro-CT in animal models is HO. Advanced histological and BSE analyses may improve confirmation of HO presence and morphology, which we demonstrated can be produced in a large animal model.

Early Bone Healing on Hydroxyapatite-Coated and Chemically-Modified Hydrophilic Implant Surfaces in an Ovine Model

Implant topography affects early peri-implant bone healing by changing the osteoconduction rate in the surrounding biological environment. Implant surfaces have been designed to promote faster and stronger bone formation for rapid and stable prosthesis loading. Early peri-implant bone healing has been observed with a sandblasted, acid-etched implant that was chemically modified to be hydrophilic (cmSLA). The present study investigates whether early peri-implant bone healing extends to a rough surface implant with a high crystalline hydroxyapatite surface (TSV MP-1 HA). Three implants were randomly placed in porous trabecular bone within both medial femoral condyles of 10 sheep. Early peri-implant bone stability was measured at 3- and 6-weeks healing time following implant insertion. Results indicated a similar implant stability quotient between the implants at insertion and over time. The significant increase over time of reverse torque values with respect to insertion torque (p < 0.001) did not differ between the implants. However, the bone-to-implant contact of TSV MP-1 HA was significantly higher than that of cmSLA implants at 6 weeks (p < 0.01). These data validate previous findings of a hydrophilic implant surface and extend the observation of early osseointegration to a rough surface implant in porous trabecular bone.

Osteogenic potential of dental and oral derived stem cells in bone tissue engineering among animal models: An update

Small bone defects can heal spontaneously through the bone modeling process due to their physiological environmental conditions. The bone modeling cycle preserves the reliability of the skeleton through the well-adjusted activities of its fundamental cell. Stem cells are a source of pluripotent cells with a capacity to differentiate into any tissue in the existence of a suitable medium. The concept of bone engineering is based on stem cells that can differentiate into bone cells. Mesenchymal stromal cells have been evaluated in bone tissue engineering due to their capacity to differentiate in osteoblasts. They can be isolated from bone marrow and from several adults oral and dental tissues such as permanent or deciduous teeth dental pulp, periodontal ligament, apical dental papilla, dental follicle precursor cells usually isolated from the follicle surrounding the third molar, gingival tissue, periosteum-derived cells, dental alveolar socket, and maxillary sinus Schneiderian membrane-derived cells. Therefore, a suitable animal model is a crucial step, as preclinical trials, to study the outcomes of mesenchymal cells on the healing of bone defects. We will discuss, through this paper, the use of mesenchymal stem cells obtained from several oral tissues mixed with different types of scaffolds tested in different animal models for bone tissue engineering. We will explore and link the comparisons between human and animal models and emphasized the factors that we need to take into consideration when choosing animals. The pig is considered as the animal of choice when testing large size and multiple defects for bone tissue engineering.

Bone ongrowth and mechanical fixation of implants in cortical and cancellous bone

BACKGROUND

What is the right surface for an implant to achieve biological fixation? Surface technologies can play important roles in encouraging interactions between the implant surface and the host bone to achieve osseointegration. Preclinical animal models provide important insight into in vivo performance related to bone ongrowth and implant fixation.

METHODS

A large animal model was used to compare the in vivo response of HA and plasma-sprayed titanium coatings in a well-reported adult ovine model to evaluate bone ongrowth in terms of mechanical properties in cortical sites, and histology and histomorphometry in cortical and cancellous sites at 4 and 12 weeks.

RESULTS

Titanium plasma-sprayed surfaces outperformed the HA-coated samples in push-out testing in cortical sites while both surfaces supported new bone ongrowth and remodeling in cortical and cancellous sites.

CONCLUSIONS

While both HA and Ti plasma provided an osteoconductive surface for bone ongrowth, the Ti plasma provided a more robust bone-implant interface that ideally would be required for load transfer and implant stability in the longer term.

In vivo osseointegration of a randomized trabecular titanium structure obtained by an additive manufacturing technique

The additive manufacturing techniques (AM) are able to realize three-dimensional trabecular structures that mimic the trabecular structure of the bone. An in vivo study in sheep was carried out with the aim of assessing the bone response and the trend of osteointegration of a randomized trabecular titanium structure produced by the AM technique. In 6 sheep were implanted 84 specimens with a trabecular titanium structure (4 implants in the femur distal epiphysis; 4 implants in the tibial plate; 6 implants in the tibial shaft). Sheep were sacrificed at 3 postoperative time-points: 6 weeks, 10 weeks, 14 weeks. Histomorphometric analysis was performed for the evaluation of Bone Implant Contact, and Bone Ingrowth. A standard push-out test was used to analyze the mechanical characteristics of the bone-implant interface. The histomorphometric data and biomechanical tests showed a fast osseointegration of the specimens both in the cancellous and in the cortical bone. The quantitative analysis of osseointegration data in cancellous bone showed the percentage of the surface of the implant in direct contact with the regenerated bone matrix significantly improved from 28% at 6 weeks to 54% at 14 weeks. An early osseointegration occurred in cortical bone showing that 75% of surface of implant was in direct contact with regenerated bone after 6 weeks; this value increased to 85% after 14 weeks. Mechanical tests revealed an early improvement of mean peak load of implants at 10 weeks (4486 N ± 528 N) compared to values at 6 weeks (2516 N ± 910 N) confirming the high rate of progression of osseointegration in the cortical bone. The non-mineralized matrix followed an increasing process of mineralization almost completely after 14 weeks. The results of this study have showed a rapid osseointegration and excellent biocompatibility for a randomized trabecular titanium structure that should be confirmed by clinical investigations.

Bioactive coating of zirconia toughened alumina ceramic implants improves cancellous osseointegration

Bioactive coatings have the potential to improve the bony integration of mechanically loaded orthopedic ceramic implants. Using the concept of mimicking the natural bone surface, four different coatings of varying thickness on a zirconia toughened alumina (ZTA) ceramic implant were investigated regarding their osseointegration in a drill-hole model in sheep. The hypothesis that a bioactive coating of ZTA ceramics would facilitate cancellous bone integration was investigated. The bioactive coatings consisted of either a layer of covalently bound multi phosphonate molecules (chemical modification = CM), a nano hydoxyapatite coating (HA), or two different bioactive glass (BG) coatings in micrometer thickness, forming a hydroxyl-carbonate apatite layer on the implant surface in vivo (dip-coated 45S5 = DipBG; sol-gel 70S30C = SGBG). Coated surfaces were characterized by scanning electron microscopy and X-ray photoelectron spectroscopy. After 12 weeks, osseointegration was evaluated via mechanical push-out testing and histology. HA enhanced the maximum push-out force (HA: mean 3573.85 ± 1119.91 N; SGBG: mean 1691.57 ± 986.76 N; p = 0.046), adhesive shear strength (HA: mean 9.82 ± 2.89 MPA; SGBG: mean 4.57 ± 2.65 MPA; p = 0.025), and energy release rate (HA: mean 3821.95 ± 1474.13 J/mm²; SGBG: mean 1558.47 ± 923.47 J/mm²; p = 0.032) compared to SGBG. The implant-bone interfacial stiffness increased by CM compared to SGBG coating (CM: mean 6258.06 ± 603.80 N/mm; SGBG: mean 3565.57 ± 1705.31 n/mm; p = 0.038). Reduced mechanical osseointegration of SGBG coated implants could be explained histologically by a foreign body reaction surrounding the implants.

Variation in bone response to the placement of percutaneous osseointegrated endoprostheses: A 24-month follow-up in sheep

Percutaneous osseointegrated (OI) devices for amputees are metallic endoprostheses, that are surgically implanted into the residual stump bone and protrude through the skin, allowing attachment of an exoprosthetic limb. In contrast to standard socket suspension systems, these percutaneous OI devices provide superior attachment platforms for artificial limbs. However, bone adaptation, which includes atrophy and/or hypertrophy along the extent of the host bone-endoprosthetic interface, is seen clinically and depends upon where along the bone the device ultimately transfers loading forces to the skeletal system. The goal of this study was to determine if a percutaneous OI device, designed with a porous coated distal region and an end-loading collar, could promote and maintain stable bone attachment. A total of eight, 18 to 24-month old, mixed-breed sheep were surgically implanted with a percutaneous OI device. For 24-months, the animals were allowed to bear weight as tolerated and were monitored for signs of bone remodelling. At necropsy, the endoprosthesis and the surrounding tissues were harvested, radiographically imaged, and histomorphometrically analyzed to determine the periprosthetic bone adaptation in five animals. Bone growth into the porous coating was achieved in all five animals. Serial radiographic data showed stress-shielding related bone adaptation occurs based on the placement of the endoprosthetic stem. When collar placement and achieved end-bearing against the transected bone, distal bone conservation/hypertrophy was observed. The results supported the use of a distally loading and distally porous coated percutaneous OI device to achieve distal host bone maintenance.

System Setup to Deliver Air Impact Forces to a Sheep Limb: Preparation for Model Development of Blast-Related Heterotopic Ossification

Background

Heterotopic ossification (HO) is a significant complication for wounded warriors with traumatic limb loss. Although this pathologic condition negatively impacts the general population, ectopic bone has been observed with higher frequency for service members injured in Iraq and Afghanistan due to blast injuries. Several factors, including a traumatic insult, bioburden, tourniquet and wound vacuum usage, and bone fractures or fragments have been associated with increased HO for service members. A large combat-relevant animal model is needed to further understand ectopic bone etiology and develop new pragmatic solutions for reducing HO formation and recurrence.

Objective

This study outlines the optimization of a blast system that may be used to simulate combat-relevant trauma for HO and replicate percussion blast experienced in theater.

Methods

We tested the repeatability and reproducibility of an air impact device (AID) at various pressure settings and compared it with a model of blunt force trauma for HO induction. Furthermore, we assessed the ability of the higher-power air delivery system to injure host tissue, displace metal particulate, and disperse bone chips in cadaveric sheep limbs.

Results

Data demonstrated that the air delivery setup generated battlefield-relevant blast forces. When the AID was charged to 40, 80, and 100 psi, the outputs were 229 (SD 13) N, 778 (SD 50) N, and 1085 (SD 114) N, respectively, compared with the blunt force model which proposed only 168 (SD 11) N. For the 100-psi AID setup, the force equaled a 5.8-kg charge weight of trinitrotoluene at a standoff distance of approximately 2.62 m, which would replicate a dismounted improvised explosive device blast in theater. Dispersion data showed that the delivery system would have the ability to cause host tissue trauma and effectively disperse metal particulate and host bone chips in local musculature compared with the standard blunt force model (13 mm vs 2 mm).

Conclusions

Our data showed that a high-pressure AID was repeatable or reproducible, had the ability to function as a simulated battlefield blast that can model military HO scenarios, and will allow for factors including blast trauma to translate toward a large animal model.

Osseointegrated Transcutaneous Device for Amputees: A Pilot Large Animal Model

Traditional above-the-knee amputation prosthetics utilize a stump-socket interface that is well-known for skin/socket problems, sitting difficulty, disuse osteopenia, and increased work of ambulation. As a result, we evaluated a novel osseointegrated transcutaneous implant in a large animal. The implant was designed to promote osseointegration at the bone-implant interface and minimize complications. As proof of concept, four Dorset sheep underwent a two-stage surgery for forelimb placement of an osseointegrated transcutaneous implant utilizing Compress® technology (Biomet, Inc., Warsaw, IN). Two sheep received a long anchor plug (90 mm long x 9 mm in diameter) and two received a short anchor plug (46 mm long x 9 mm in diameter). Sixteen weeks after the initial surgery, the operative limbs, along with the attached implant, underwent radiographic and histological analysis for osseointegration. Periprosthetic fractures occurred in the two animals that received the longer internal prosthesis; one healed with splinting and the other animal underwent a second surgical procedure to advance the amputation site more proximal. No fractures occurred in the shorter internal prosthesis group. There was no histological evidence of infection and none of the transcutaneous adapters failed. Bone-implant osseointegration was demonstrated in two of three limbs that underwent histological analysis. This unique implant demonstrated osseointegration without transcutaneous adapter failure, all while displaying minimal infection risk from the outside environment. Although it involved short-term follow-up in a limited number of animals, this pilot study provides a platform for further investigation into the valid concept of using Compress® technology as an endo-exo device.

Comparison of polyetheretherketone versus silicon nitride intervertebral spinal spacers in a caprine model

Polyetheretherketone (PEEK) is commonly used as a spinal spacer for intervertebral fusion surgery. Unfortunately, PEEK is bioinert and does not effectively osseointegrate into living bone. In contrast, comparable spacers made of silicon nitride (Si₃ N₄ ) possess a surface nanostructure and chemistry that encourage appositional bone healing. This observational study was designed to compare the outcomes of these two biomaterials when implanted as spacers in an adult caprine model. Lumbar interbody fusion surgeries were performed at two adjacent levels in eight adult goats using implants of PEEK and Si₃ N₄ . At six-months after surgery, the operative and adjacent spinal segments were extracted and measured for bone fusion, bone volume, bone-implant contact (BIC) and soft-tissue implant contact (SIC) ratios, and biodynamic stability. The null hypothesis was that no differences in these parameters would be apparent between the two groups. Fusion was observed in seven of eight implants in each group with greater bone formation in the Si₃ N₄ group (52.6%) versus PEEK (27.9%; p = 0.2). There were no significant differences in BIC ratios between PEEK and Si₃ N₄ , and the biodynamic stability of the two groups was also comparable. The results suggest that Si₃ N₄ spacers are not inferior to PEEK and they may be more effective in promoting arthrodesis. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 00B: 000-000, 2018. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 688-699, 2019.

Methodology to Produce Specimen-Specific Models of Vertebrae: Application to Different Species

Image-based continuum-level finite element models have been used for bones to evaluate fracture risk and the biomechanical effects of diseases and therapies, capturing both the geometry and tissue mechanical properties. Although models of vertebrae of various species have been developed, an inter-species comparison has not yet been investigated. The purpose of this study was to derive species-specific modelling methods and compare the accuracy of image-based finite element models of vertebrae across species. Vertebral specimens were harvested from porcine (N = 12), ovine (N = 13) and bovine (N = 14) spines. The specimens were experimentally loaded to failure and apparent stiffness values were derived. Image-based finite element models were generated reproducing the experimental protocol. A linear relationship between the element grayscale and elastic modulus was calibrated for each species matching in vitro and in silico stiffness values, and validated on independent sets of models. The accuracy of these relationships were compared across species. Experimental stiffness values were significantly different across species and specimen-specific models required species-specific linear relationship between image grayscale and elastic modulus. A good agreement between in vitro and in silico values was achieved for all species, reinforcing the generality of the developed methodology.

Retrieval Analysis of Porous Titanium Glenoid Posts: An Evaluation of Osteointegration

Glenoid component loosening is a commonly encountered complication of total shoulder replacements. Therefore, focus has been placed on glenoid fixation. Porous metal implants, which promote biological fixation through osteointegration, have provided an uncemented alternative to the traditional cemented implant. In this explantation study, the authors examined the bone ingrowth and ongrowth of a specific porous titanium glenoid peg. Six explanted polyethylene glenoid components with porous titanium-coated central pegs were identified in the authors' implant retrieval program via retrospective review. The retrieved implants were sectioned into thirds with a precision saw and underwent scanning electron microscopy for analysis of bone ingrowth and ongrowth. Bone ingrowth was calculated as bone volume fraction, or the fraction of available pore space filled with bone, whereas ongrowth was the percentage of the perimeter of the implant covered with bone. The 6 total shoulders included in the study were revised at an average of 16.3 months (range, 5-48 months) for instability secondary to subscapularis rupture, subscapularis rupture plus infection, or other rotator cuff tear. All glenoid components were grossly stable on retrieval and had an average of 23% bone ingrowth and 54% ongrowth. The preliminary results show that osteointegration into a porous titanium ingrowth glenoid component is possible in the short-term, even in the presence of an unfavorable biomechanical environment, such as instability and rotator cuff dysfunction, as well as infection. [Orthopedics. 2017; 40(4):e703-e707.].

Fortifying the Bone-Implant Interface Part 2: An In Vivo Evaluation of 3D-Printed and TPS-Coated Triangular Implants

BACKGROUND

Minimally invasive surgical fusion of the sacroiliac (SI) joint using machined solid triangular titanium plasma spray (TPS) coated implants has demonstrated positive clinical outcomes in SI joint pain patients. Additive manufactured (AM), i.e. 3D-printed, fenestrated triangular titanium implants with porous surfaces and bioactive agents, such as nanocrystalline hydroxyapatite (HA) or autograft, may further optimize bony fixation and subsequent biomechanical stability.

METHODS

A bilateral ovine distal femoral defect model was used to evaluate the cancellous bone-implant interfaces of TPS-coated and AM implants. Four implant groups (n=6/group/time-point) were included: 1)TPS-coated, 2)AM, 3)AM+HA, and 4)AM+Autograft. The bone-implant interfaces of 6- and 12-week specimens were investigated via radiographic, biomechanical, and histomorphometric methods.

RESULTS

Imaging showed peri-implant bone formation around all implants. Push-out testing demonstrated forces greater than 2500 N, with no significant differences among groups. While TPS implants failed primarily at the bone-implant interface, AM groups failed within bone ~2-3mm away from implant surfaces. All implants exhibited bone ongrowth, with no significant differences among groups. AM implants had significantly more bone ingrowth into their porous surfaces than TPS-coated implants (p<0.0001). Of the three AM groups, AM+Auto implants had the greatest bone ingrowth into the porous surface and through their core (p<0.002).

CONCLUSIONS

Both TPS and AM implants exhibited substantial bone ongrowth and ingrowth, with additional bone through growth into the AM implants' core. Overall, AM implants experienced significantly more bone infiltration compared to TPS implants. While HA-coating did not further enhance results, the addition of autograft fostered greater osteointegration for AM implants.

CLINICAL RELEVANCE

Additive manufactured implants with a porous surface provide a highly interconnected porous surface that has comparatively greater surface area for bony integration. Results suggest this may prove advantageous toward promoting enhanced biomechanical stability compared to TPS-coated implants for SI joint fusion procedures.

Silicon Nitride (Si3N4) Implants: The Future of Dental Implantology?

For decades titanium has been the preferred material for dental implant fabrication, with mechanical and biological performance resulting in high clinical success rates. These have been further enhanced by incremental development of surface modifications aimed at improving speed and degree of osseointegration and resulting in enhanced clinical treatment options and outcomes. However, increasing demand for metal-free dental restorations has also led to the development of ceramic-based dental implants, such as zirconia. In orthopedics, alternative biomaterials, such as polyetheretherketone or silicon nitride, have been used for implant applications. The latter is potentially of particular interest for oral use as it has been shown to have antibacterial properties. In this article we aim to shed light on this particular biomaterial as a future promising candidate for dental implantology applications, addressing basic specifications required for any dental implant material. In view of available preclinical data, silicon nitride seems to have the essential characteristics to be a candidate for dental implants material. This novel ceramic has a surface with potentially antimicrobial properties, and if this is confirmed in future research, it could be of great interest for oral use.

Comparison of nanoparticular hydroxyapatite pastes of different particle content and size in a novel scapula defect model

Nanocrystalline hydroxyapatite (HA) has good biocompatibility and the potential to support bone formation. It represents a promising alternative to autologous bone grafting, which is considered the current gold standard for the treatment of low weight bearing bone defects. The purpose of this study was to compare three bone substitute pastes of different HA content and particle size with autologous bone and empty defects, at two time points (6 and 12 months) in an ovine scapula drillhole model using micro-CT, histology and histomorphometry evaluation. The nHA-LC (38% HA content) paste supported bone formation with a high defect bridging-rate. Compared to nHA-LC, Ostim® (35% HA content) showed less and smaller particle agglomerates but also a reduced defect bridging-rate due to its fast degradation The highly concentrated nHA-HC paste (48% HA content) formed oversized particle agglomerates which supported the defect bridging but left little space for bone formation in the defect site. Interestingly, the gold standard treatment of the defect site with autologous bone tissue did not improve bone formation or defect bridging compared to the empty control. We concluded that the material resorption and bone formation was highly impacted by the particle-specific agglomeration behaviour in this study.

Link Between Clinical Predictors of Heterotopic Ossification and Histological Analysis in Combat-Injured Service Members

BACKGROUND

Heterotopic ossification (HO) is a debilitating condition that occurs following traumatic injury and may restrict range of motion and delay rehabilitation. The timing and efficacy of surgical resection have varied widely, and there is a gap in knowledge between clinical predictors of HO recurrence and histological analysis.

METHODS

Thirty-three service members seen at Walter Reed National Military Medical Center for symptomatic HO were enrolled in an institutional review board-approved study. Participants took oxytetracycline on four scheduled days prior to HO resection to determine the mineral apposition rate (bone growth rate).

RESULTS

Detailed histological analyses included scanning electron microscopy with backscattered electron imaging and light microscopy. Data indicated that the mineral apposition rate of trauma-induced HO was approximately 1.7 μm/day at the time of operative intervention, which was 1.7 times higher than the rate in non-pathological human bone. The mineral apposition rate and postoperative alkaline phosphatase values were demonstrated to be positively and significantly related (ρ = 0.509, p = 0.026, n = 19). When the analysis was limited to patients with no more than a two-year period from injury to excision (thereby removing outliers who had a longer time period than their counterparts) and traumatic brain injury and nonsteroidal anti-inflammatory drugs (known correlates with HO development) were controlled for in the statistical analysis, the mineral apposition rate and recurrence severity were significantly related (ρ = -0.572, p = 0.041, n = 11).

CONCLUSIONS

Data demonstrated a link between benchtop research and bedside care, with the mineral apposition rate elevated in patients with HO and correlated with recurrence severity; however, a larger sample size and more clinical factors are needed to refine this model.

LEVEL OF EVIDENCE

Prognostic Level II. See Instructions for Authors for a complete description of levels of evidence.

Preclinical testing of drug delivery systems to bone

Bone defects do not heal in 5-10% of the fractures. In order to enhance bone regeneration, drug delivery systems are needed. They comprise a scaffold with or without inducing factors and/or cells. To test these drug delivery systems before application in patients, they finally need to be tested in animal models. The choice of animal model depends on the main research question; is a functional or mechanistic evaluation needed? Furthermore, which type of bone defects are investigated: load-bearing (i.e. orthopedic) or non-load-bearing (i.e. craniomaxillofacial)? This determines the type of model and in which type of animal. The experiments need to be set-up using the 3R principle and must be reported following the ARRIVE guidelines.

The effect of aging on posterior intertransverse lumbar fusion: a New Zealand white rabbit model

STUDY DESIGN

In vivo assessment of lumbar spinal fusion between a younger and older cohort of New Zealand white rabbits.

OBJECTIVE

Directly compare fusion within young and aged New Zealand white rabbits to establish an aged spinal fusion model translational research.

SUMMARY OF BACKGROUND DATA

Prior studies have utilized skeletally mature young rabbits (6-12 mo old) that may not be appropriate as an analog for studying the aging human spine.

METHODS

Ten aged (>36 mo old) and 10 young (12 mo old) New Zealand white rabbits underwent a single-level, bilateral, L5-6 posterolateral intertransverse fusion using autogenous iliac crest bone graft. The animals were killed at 6 weeks postoperatively, and the specimens were then evaluated with quantitative microcomputerized tomography and manual palpation by 6 orthopedic surgeons. The fusions were graded as either fused or not fused by each examiner. The spines were then embedded in poly(methyl methacrylate) and cut into 2-mm-thick sections for histologic analysis.

RESULTS

A higher percentage of young rabbits were determined to be successfully fused through manual palpation testing compared with the aged rabbits. Micro-computed tomography (CT) analysis revealed a significantly greater fusion mass volume in the younger rabbits than in the older cohort. In addition, the fusion density of the younger rabbits was found to be significantly lower than that of the older rabbits when normalized to the bone density in the nonfused portion of the spine. Histologic analysis showed that the quality of the bone within the fusion mass was consistent between the young and old rabbits. A greater number of young animals had bilateral continuous bone graft compared with the aged animals.

CONCLUSIONS

The aged (>36 mo) New Zealand white rabbit model appears to be a valid model to evaluate the effect of aging on lumbar fusion and has the potential to more accurately model conditions that are present in the older human spine.

Bone defect animal models for testing efficacy of bone substitute biomaterials

Large bone defects are serious complications that are most commonly caused by extensive trauma, tumour, infection, or congenital musculoskeletal disorders. If nonunion occurs, implantation for repairing bone defects with biomaterials developed as a defect filler, which can promote bone regeneration, is essential. In order to evaluate biomaterials to be developed as bone substitutes for bone defect repair, it is essential to establish clinically relevant in vitro and in vivo testing models for investigating their biocompatibility, mechanical properties, degradation, and interactional with culture medium or host tissues. The results of the in vitro experiment contribute significantly to the evaluation of direct cell response to the substitute biomaterial, and the in vivo tests constitute a step midway between in vitro tests and human clinical trials. Therefore, it is essential to develop or adopt a suitable in vivo bone defect animal model for testing bone substitutes for defect repair. This review aimed at introducing and discussing the most available and commonly used bone defect animal models for testing specific substitute biomaterials. Additionally, we reviewed surgical protocols for establishing relevant preclinical bone defect models with various animal species and the evaluation methodologies of the bone regeneration process after the implantation of bone substitute biomaterials. This review provides an important reference for preclinical studies in translational orthopaedics.

Refixation of Osteochondral Fractures by an Ultrasound-Activated Pin System - An Ovine In Vivo Examination Using CT and Scanning Electron Microscope

Background:

Osteochondral injuries, if not treated appropriately, often lead to severe osteoarthritis of the affected joint. Without refixation of the osteochondral fragment, human cartilage only repairs these defects imperfectly. All existing refixation systems for chondral defects have disadvantages, for instance bad MRI quality in the postoperative follow-up or low anchoring forces. To address the problem of reduced stability in resorbable implants, ultrasound-activated pins were developed. By ultrasound-activated melting of the tip of these implants a higher anchoring is assumed. Aim of the study was to investigate, if ultrasound-activated pins can provide a secure refixation of osteochondral fractures comparing to conventional screw and conventional, resorbable pin osteosynthesis. CT scans and scanning electron microscopy should proovegood refixation results with no further tissue damage by the melting of the ultrasound-activated pins in comparison to conventional osteosynthesis.

Methods:

Femoral osteochondral fragments in sheep were refixated with ultrasound-activated pins (SonicPin™), Ethipins^® and screws (Asnis™). The quality of the refixated fragments was examined after three month of full weight bearing by CT scans and scanning electron microscopy of the cartilage surface.

Results:

The CT examination found almost no statistically significant difference in the quality of refixation between the three different implants used. Concerning the CT morphology, ultrasound-activated pins demonstrated at least the same quality in refixation of osteochondral fragments as conventional resorbable pins or screws. The scanning electron microscopy showed no major surface damage by the three implants, especially any postulated cartilage damage induced by the heat of the ultrasound-activated pin. The screws protruded above the cartilage surface, which may affect the opposingtibial surface.

Conclusion:

Using CT scans and scanning electron microscopy, the SonicPin™, the Ethipin^® and screws were at least equivalent in refixation quality of osteochondral fragments.

Neoformação óssea e osteointegração de biomateriais micro e nanoestruturados em ovinos

A substituição de parte do tecido ósseo se faz necessária muitas vezes na rotina cirúrgica, seja em função de fraturas, neoplasias ósseas ou enfermidades ortopédicas que acarretem em perda óssea. Neste sentido, têm se buscado biomateriais capazes de promover esta substituição, evitando o uso de enxertos ou transplantes ósseos. O objetivo deste trabalho foi avaliar a capacidade osteoregenerativa de biomateriais em diferentes composições, em tíbias de ovinos. Foram utilizadas oito ovelhas mestiças texel, com 12 meses de idade e peso médio de 28,5±7,4kg. Após adequada preparação anestésica e cirúrgica, foram produzidos três defeitos ósseos na diáfise das tíbias em sua face medial, totalizando seis defeitos de 6mm cada, sendo que quatro foram preenchidos por biomateriais, e dois por fragmentos ósseos retirados do próprio animal (autocontrole). Os materiais implantados foram: hidroxiapatita (HA), tricálcio fosfato-β (TCP-β), hidroxiapatita/tricálcio fosfato-b 60/40 (HA/TCP-b 60/40) e o nanocompósito hidroxiapatita/alumina a 5% (HA/Al2O3 a 5%). Os animais foram alocados em dois grupos: Grupo 60 (n=04), em que os animais foram eutanasiados após 60 dias da colocação dos implantes e Grupo 90 (n=04), em que a eutanásia ocorreu 90 dias após a colocação dos implantes. Foram realizadas radiografias nos períodos pré-operatório, imediatamente após o procedimento e aos 30, 60 e 90 dias de pós-operatório, a fim de excluir qualquer alteração prévia ou complicação pós-operatória, capaz de comprometer o estudo. Após a eutanásia, foram coletadas as tíbias para avaliação macro e microscópica, por meio de microscopia eletrônica de varredura (MEV) e microscopia óptica. Os resultados encontrados mostraram uma boa capacidade de neoformação óssea e uma lenta absorção da HA. O TCP-β foi rapidamente absorvido e apresentou boa capacidade osteoindutiva e osteocondutiva, sendo observada neoformação óssea no interior dos grânulos deste biomaterial. O composto bifásico HA/TCP-β (60/40) apresentou o melhor resultado a longo prazo, devido ao melhor controle na solubilização e liberação dos íons cálcio e fosfatos para o meio biológico durante o processo de neoformação óssea. O biomaterial nanocompósito HA/Al2O3 a 5% não apresentou resultados promissores neste estudo, e sugerem-se novas pesquisas a fim de investigar melhor o potencial e aplicabilidade deste novo biomaterial. Conclui-se que a hidroxiapatita, o tricálcio fosfato-β e a associação HA/TCP-β (60/40) apresentam excelente capacidade de reparação óssea, podendo ser utilizados como substitutos ósseos; a associação HA/TCP-β (60/40) é o melhor dentre os biomateriais estudados, pois apresenta velocidade de absorção intermediária em relação à HA e ao TCP-β isolados, fornecendo ainda uma sustentação adequada ao tecido neoformado; o biomaterial HA/Al2O3 5% se mostrou incompatível, provocando reação de rejeição por parte do hospedeiro e com insignificante formação de tecido ósseo, sugerindo novas pesquisas acerca deste material.

Diffusion model to describe osteogenesis within a porous titanium scaffold

In this study, we develop a two-dimensional finite element model, which is derived from an animal experiment and allows simulating osteogenesis within a porous titanium scaffold implanted in ewe's hemi-mandible during 12 weeks. The cell activity is described through diffusion equations and regulated by the stress state of the structure. We compare our model to (i) histological observations and (ii) experimental data obtained from a mechanical test done on sacrificed animal. We show that our mechano-biological approach provides consistent numerical results and constitutes a useful tool to predict osteogenesis pattern.

Progression of bone ingrowth and attachment strength for stability of percutaneous osseointegrated prostheses

BACKGROUND

Percutaneous osseointegrated prosthetic (POP) devices have been used clinically in Europe for decades. Unfortunately, their introduction into the United States has been delayed, in part due to the lack of data documenting the progression of osseointegration and mechanical stability.

QUESTIONS/PURPOSES

We determined the progression of bone ingrowth into porous-coated POP devices and established the interrelationship with mechanical stability.

METHODS

After amputation, 64 skeletally mature sheep received a custom porous-coated POP device and were then randomized into five time groups, with subsequent measurement of percentage of bone ingrowth into the available pore spaces (n = 32) and the mechanical pullout force (n = 32).

RESULTS

Postimplantation, there was an accelerated progression of bone ingrowth (~48% from 0 to 3 months) producing a mean pullout force of 5066 ± 1543 N. Subsequently, there was a slower but continued progression of bone ingrowth (~23% from 3 to 12 months) culminating with a mean pullout force of 13,485 ± 1855 N at 12 months postimplantation. There was a high linear correlation (R = 0.94) between the bone ingrowth and mechanical pullout stability.

CONCLUSIONS

This weightbearing model shows an accelerated progression of bone ingrowth into the porous coating; the amount of ingrowth observed at 3 months after surgery within the porous-coated POP devices was sufficient to generate mechanical stability.

CLINICAL RELEVANCE

The data document progression of bone ingrowth into porous-coated POP devices and establish a strong interrelationship between ingrowth and pullout strength. Further human data are needed to validate these findings.

Refixation of osteochondral fractures by ultrasound-activated, resorbable pins: An ovine in vivo study

Objectives

Osteochondral injuries, if not treated adequately, often lead to severe osteoarthritis. Possible treatment options include refixation of the fragment or replacement therapies such as Pridie drilling, microfracture or osteochondral grafts, all of which have certain disadvantages. Only refixation of the fragment can produce a smooth and resilient joint surface. The aim of this study was the evaluation of an ultrasound-activated bioresorbable pin for the refixation of osteochondral fragments under physiological conditions.

Methods

In 16 Merino sheep, specific osteochondral fragments of the medial femoral condyle were produced and refixed with one of conventional bioresorbable pins, titanium screws or ultrasound-activated pins. Macro- and microscopic scoring was undertaken after three months.

Results

The healing ratio with ultrasound-activated pins was higher than with conventional pins. No negative heat effect on cartilage has been shown.

Conclusion

As the material is bioresorbable, no further surgery is required to remove the implant. MRI imaging is not compromised, as it is with implanted screws. The use of bioresorbable pins using ultrasound is a promising technology for the refixation of osteochondral fractures.

Model development for determining the efficacy of a combination coating for the prevention of perioperative device related infections: a pilot study

Antibiotic resistant bacterial infections are a growing problem in patient care. These infections are difficult to treat and severely affect the patient's quality of life. The goal of this translational experiment was to investigate the antimicrobial potential of cationic steroidal antimicrobial-13 (CSA-13) for the prevention of perioperative device-related infections in vivo. It was hypothesized that when incorporated into a polymeric device coating, the release of CSA-13 could prevent perioperative device-related infection without inhibiting skeletal attachment. To test this hypothesis, 12 skeletally mature sheep received a porous coated titanium implant in the right femoral condyle. Group 1 received the titanium implant and an inoculum of 5 × 10(8) CFU of methicillin-resistant Staphylococcus aureus (MRSA). Group 2 received a CSA-13 coated implant and the MRSA inoculum. Group 3 received only the CSA-13 coated implant and Group 4 received only the implant-without the CSA-13 coating or MRSA inoculum. In conclusion, the CSA-13 combination coating demonstrated bactericidal potential without adversely affecting skeletal attachment. The CSA-13 containing groups exhibited no evidence of bacterial infection at the conclusion of the 12 week study and established skeletal attachment consistent with Group 4. In contrast, all of the Group 1 animals became infected and required euthanasia within 6-10 days. The significance of this finding is that this combination coating could be applied to implanted devices to prevent perioperative device-related infections. This method may facilitate significantly reduced incidences of device-related infections as well as a new method to treat and prevent resistant strain bacterial infections.

Cortical bone response to the presence of load-bearing percutaneous osseointegrated prostheses

Although the current percutaneous osseointegrated (OI) prosthetic attachment systems are novel clinical treatments for patients with limb loss, there have only been limited translational studies undertaken to date. To bridge this knowledge gap, from a larger study group of 86 animals that were implanted with a novel percutaneous OI implant construct, 33 sheep were randomly selected from the 0-, 3-, 6-, 9- and 12-month groups for histomorphometric analyses of periprosthetic cortical bone tissue. At necropsy, implanted and nonimplanted limbs were harvested and processed for the evaluation of cortical bone porosity and mineral apposition rate (MAR). The data showed a maximum increase in bone porosity within the first 3 months following implantation and then a progressive reduction in porosity to the baseline steady-state ("Time 0") value by 12 months. The data further verified that the MAR increased during the first 6 months of implantation, reaching a plateau between 6 and 9 months, followed by a progressive decline to the baseline steady state. It was concluded that clinical load bearing and falls precautions, taken during the first 3-6 months following percutaneous OI device implantation surgery, could greatly limit bone fractures during this vulnerable time of increasing cortical bone porosity.

Does using autograft bone chips achieve consistent bone ingrowth in primary TKA?

BACKGROUND

Cementless fixation remains controversial in TKA due to the challenge of achieving consistent skeletal attachment. Factors predicting durable fixation are not clearly understood, but we presumed bone ingrowth could be enhanced by the quantity of host bone and application of autograft bone chips.

QUESTIONS/PURPOSES

We asked: (1) Did the amount of bone ingrowth exceed the amount of periprosthetic and host bone with the addition of autograft bone chips? (2) Did the amount of bone ingrowth increase with implantation time? And (3) did osteolysis along the porous-coated interface and screw tracts progress with implantation time?

METHODS

We measured the amount of bone in the porous-coated, periprosthetic, and host bone regions in 19 postmortem retrieved cementless primary total knee implants. The amount of bone in apposition to the implant surface, and alternatively lysed bone, was analyzed radiographically to assess the progression of osteolysis.

RESULTS

While bone ingrowth tended to be less than periprosthetic and host bone in all three components, it was only significantly less in the patellar component. Bone ingrowth increased in all three components over time, but progression of osteolysis did not.

CONCLUSIONS

Even after long-term followup, the amount of bone ingrowth did not surpass host bone levels, suggesting the amount of a patient's host bone is a limiting factor in the amount of bone ingrowth achievable for this cementless design. It remains unknown whether compromised osteopenic bone could achieve the amount of bone attachment necessary to provide durable fixation over time.

Host bone response to polyetheretherketone versus porous tantalum implants for cervical spinal fusion in a goat model

STUDY DESIGN

In vivo assessment of polyetheretherketone (PEEK) and porous tantalum (TM) cervical interbody fusion devices in a goat model.

OBJECTIVE

Directly compare host bone response to PEEK and TM devices used for cervical interbody fusion.

SUMMARY OF BACKGROUND DATA

PEEK devices are widely used for anterior cervical discectomy and fusion but are nonporous and have limited surface area for bone attachment.

METHODS

Twenty-five goats underwent single-level anterior cervical discectomy and fusion and were alternately implanted with TM (n = 13) or PEEK devices (n = 12) for 6, 12, and 26 weeks. Both devices contained a center graft hole (GH), filled with autograft bone from the animal's own iliac crest. The percentage of bone tissue around the implant, percentage of the implant surface in direct apposition with the host bone, and evidence of bone bridging through the implant GH were assessed by using backscattered electron imaging. Bone matrix mineral apposition rate was determined through fluorochrome double labeling, and sections were stained for histological analysis.

RESULTS

The TM-implanted animals had significantly greater volumes of bone tissue at the implant interface than the PEEK animals at all-time points. The TM animals also had a significantly greater average mineral apposition rate in the GH region at 6 and 12 weeks than the PEEK animals. No difference was observed at 26 weeks. A greater number of TM-implanted animals demonstrated connection between the autograft bone and both vertebrae compared with the PEEK implants. Histological staining also showed that the TM devices elicited improved host bone attachment over the PEEK implants.

CONCLUSION

The TM implants supported bone growth into and around the implant margins better than the PEEK devices. TM's open cell porous structure facilitated host bone ingrowth and bone bridging through the device, which could be beneficial for long-term mechanical attachment and support in clinical applications.

Rapid Heterotrophic Ossification with Cryopreserved Poly(ethylene glycol-) Microencapsulated BMP2-Expressing MSCs

Autologous bone grafting is the most effective treatment for long-bone nonunions, but it poses considerable risks to donors, necessitating the development of alternative therapeutics. Poly(ethylene glycol) (PEG) microencapsulation and BMP2 transgene delivery are being developed together to induce rapid bone formation. However, methods to make these treatments available for clinical applications are presently lacking. In this study we used mesenchymal stem cells (MSCs) due to their ease of harvest, replication potential, and immunomodulatory capabilities. MSCs were from sheep and pig due to their appeal as large animal models for bone nonunion. We demonstrated that cryopreservation of these microencapsulated MSCs did not affect their cell viability, adenoviral BMP2 production, or ability to initiate bone formation. Additionally, microspheres showed no appreciable damage from cryopreservation when examined with light and electron microscopy. These results validate the use of cryopreservation in preserving the viability and functionality of PEG-encapsulated BMP2-transduced MSCs.

Percutaneous osseointegrated prostheses for amputees: Limb compensation in a 12-month ovine model

Percutaneous osseointegrated prostheses are being investigated as an alternative strategy to attach prosthetic limbs to patients. Although the use of these implants has shown to be promising in clinical trials, the ability to maintain a skin seal around an osseointegrated implant interface is a major challenge to prevent superficial and deep periprosthetic infections. The specific aim of this study was to establish a translational load-bearing ovine model to assess postoperative limb compensation and gait symmetry following a percutaneous osseointegrated implant. We tested the following hypotheses: (1) the animals would return to pre-amputation limb loads within 12-months; (2) the animals would return to a symmetrical gait pattern (stride length and time in stance) within 12-months. The results demonstrated that one month following surgery, the sheep loaded their amputated limb to a mean value of nearly 80% of their pre-amputation loading condition; by 12-months, this mean had dropped to approximately 74%. There was no statistical differences between the symmetry of the amputated forelimb and the contralateral forelimb at any time point for the animals stride length or the time spent in the stance phase of their gait cycle. Thus, the data showed that while the animals maintained symmetric gait patterns, they did not return to full weight-bearing after 12-months. The results of this study showed that a large animal load-bearing model had a symmetric gait and was weight bearing for up to 12 months. While the current investigation utilizes an ovine model, the data show that osseointegrated implant technology with postoperative follow-up can help our human patients return to symmetric gait and maintain an active lifestyle, leading to an improvement in their quality of life following amputation.

Evaluating antimicrobials and implant materials for infection prevention around transcutaneous osseointegrated implants in a rabbit model

Transcutaneous osseointegrated implants can improve function for select amputee patients, but infection serves as a significant limitation of implantable transcutaneous devices. This study examined the efficacy of an antimicrobial, pexiganan acetate (SUPONEX), and a porous tantalum implant material (Trabecular Metal) in preventing pin tract infection of osseointegrated implants in a rabbit model. Thirty-seven rabbits were randomized to three groups: Ti-control group (n = 11) with titanium alloy implant and no antimicrobial, Ti-Pexiganan group (n = 8) with titanium alloy implant and topical pexiganan acetate 1% applied daily at the skin/implant interface, and Ta-control group (n = 18) with porous tantalum implant and no antimicrobial. All implants were placed transcutaneously through skin, muscle, and bone. Rabbits were monitored for infection for 24 weeks. We observed a 75% reduction in rates of pin tract infection in the Ti-Pexiganan group compared to that observed in the Ti-control group (p = 0.019). No difference in rates of infection was observed between the Ta-control group and the Ti-control group (p = 0.230). In conclusion, pexiganan acetate may be an important antimicrobial for transcutaneous osseointegrated implants. Porous tantalum will not likely prevent pin tract infection without additional methods of soft tissue immobilization around the implant site.

Osseointegration into a novel titanium foam implant in the distal femur of a rabbit

A novel porous titanium foam implant has recently been developed to enhance biological fixation of orthopaedic implants to bone. The aim of this study was to examine the mechanical and histological characteristics of bone apposition into two different pore sizes of this titanium foam (565 and 464 micron mean void intercept length) and to compare these characteristics to those obtained with a fully porous conventionally sintered titanium bead implant. Cylindrical implants were studied in a rabbit distal femoral intramedullary osseointegration model at time zero and at 3, 6, and 12 weeks. The amount of bone ingrowth, amount of periprosthetic bone, and mineral apposition rate of periprosthetic bone measured did not differ among the three implant designs at 3, 6, or 12 weeks. By 12 weeks, the interface stiffness and maximum load of the beaded implant was significantly greater than either foam implant. No significant difference was found in the interface stiffness or maximum load between the two foam implant designs at 3, 6, or 12 weeks. The lower compressive modulus of the foam compared to the more dense sintered beaded implants likely contributed to the difference in failure mode. However, the foam implants have a similar compressive modulus to other clinically successful coatings, suggesting they are nonetheless clinically adequate. Additional studies are required to confirm this in weight-bearing models. Histological data suggest that these novel titanium foam implants are a promising alternative to current porous coatings and should be further investigated for clinical application in cementless joint replacement.

Bone ingrowth into porous silicon nitride

Achieving solid skeletal attachment is a requirement for the clinical success of orthopedic implants. Porous or roughened surfaces and coatings have been developed and used with mixed success to achieve attachment due to bone ingrowth. Silicon nitride is a high performance ceramic whose strength, imaging properties, and biocompatibility make it a candidate material for orthopedic implants. A porous form of silicon nitride, cancellous-structured ceramic (CSC), has been developed. CSC is a nonresorbable, partially radiolucent porous structure that can be bonded to orthopedic implants made of silicon nitride to facilitate skeletal attachment. The purpose of this study was to quantify the extent and rate of bone ingrowth into CSC in a large animal model. Cylindrical implants were placed bilaterally using staged surgeries in the medial femoral condyle of six sheep. Condyles were retrieved after 3 and 6 months in situ and prepared for examination of bone growth under SEM. Bone grew into CSC to extents and at rates similar to those reported for other titanium porous surfaces in studies involving large animals and postmortem retrievals in humans. Bone ingrowth was observed at depths of penetration greater than 3 mm in some implants after only 12 weeks in situ. Bone ingrowth into CSC is a viable method for achieving skeletal attachment.

Biocompatibility and osseointegration of reconstituted keratin in an ovine model

Reconstituted keratin has potential as a raw material for orthopaedic applications. The aim of this study was to investigate the in vivo biocompatibility and osseointegration of keratin materials in an ovine model. Six different modifications of the keratin polymer, based on porous or dense constructs, regenerated by either neutral or acidic treatment, with or without hydroxyapatite, were made as small rods and inserted into drilled round defects in the femur and tibia of sheep. Histology was carried out on samples taken at different time points up to 24 weeks postsurgery. All keratin implants showed similar histological profiles, which included granulation tissue surrounding and infiltrating the implants, followed by new bone formation radiating from the existing bone. By 8 weeks, new bone had grown to within a short distance of the implant surface, and in some places was in direct apposition to the keratin implant. In the 12 to 24-week period, there was peripheral resorption and infiltration of bony trabeculae with regard to the porous constructs only. The tissue reaction appeared to model that of a fairly inert material. Further work on improving the extent of osseointegration and acceleration of the biodegradation rate of reconstituted keratin is underway.