Progress in low-loss and high-bandwidth plastic optical fibers

Optical synchronous signal demodulation-based quartz-enhanced photoacoustic spectroscopy for remote, multi-point methane detection in complex environments

We present a novel optical synchronized signal demodulation (OSSD) method applied in quartz-enhanced photoacoustic spectroscopy (QEPAS) for remote gas sensing. Using 1 % of the laser source as an optical synchronization signal, kilometer-scale remote gas detection was achieved, overcoming the challenges of long-distance real-time detection in complex environments with conventional QEPAS. A time-sharing OSSD-QEPAS system for sewer methane detection was subsequently developed. The system's modulation depth was optimized, and the catalytic effect of water vapor on photoacoustic signals was validated, resulting in a CH₄ sensor achieving a detection limit of 445 ppb with a 300-ms averaging time, and an excellent linear dynamic range with a R2 = 0.999. To demonstrate the stability, robustness, and accuracy of the OSSD-QEPAS system, continuous methane measurements covering a 14-hour period at two different sewer locations on campus were performed.

High bandwidth performance of newly designed multimode W-type microstructured plastic optical fibers with graded-index core distribution

A new design of multimode W-type (doubly clad) microstructured plastic optical fiber (mPOF) with graded-index (GI) distribution of the core is proposed, along with a methodology for examining transmission along it. The power flow equation's (PFE) numerical solution yields the transmission properties of the W-type GI mPOF. We have demonstrated that the coupling length Lc at which an equilibrium mode distribution (EMD) is reached in W-type GI mPOF is shorter than the length experimentally found for the conventional singly- clad (SC) GI POF. This results from leaky mode losses, which lower the length Lc in W-type GI mPOF by lowering the amount of higher guided modes engaged in the coupling process. As a result, the bandwidth of W-type GI mPOF significantly increases. It is noteworthy that, when compared to the experimental bandwidth of commercially available conventional POFs, the bandwidth of the W-type GI mPOF proposed in this work is noticeably higher. Consequently, the bandwidth performance of short-haul communication lines may be significantly improved by using such a designed W-type GI mPOF.

Plasmonic nanoparticle sensors: current progress, challenges, and future prospects

Plasmonic nanoparticles (NPs) have played a significant role in the evolution of modern nanoscience and nanotechnology in terms of colloidal synthesis, general understanding of nanocrystal growth mechanisms, and their impact in a wide range of applications. They exhibit strong visible colors due to localized surface plasmon resonance (LSPR) that depends on their size, shape, composition, and the surrounding dielectric environment. Under resonant excitation, the LSPR of plasmonic NPs leads to a strong field enhancement near their surfaces and thus enhances various light-matter interactions. These unique optical properties of plasmonic NPs have been used to design chemical and biological sensors. Over the last few decades, colloidal plasmonic NPs have been greatly exploited in sensing applications through LSPR shifts (colorimetry), surface-enhanced Raman scattering, surface-enhanced fluorescence, and chiroptical activity. Although colloidal plasmonic NPs have emerged at the forefront of nanobiosensors, there are still several important challenges to be addressed for the realization of plasmonic NP-based sensor kits for routine use in daily life. In this comprehensive review, researchers of different disciplines (colloidal and analytical chemistry, biology, physics, and medicine) have joined together to summarize the past, present, and future of plasmonic NP-based sensors in terms of different sensing platforms, understanding of the sensing mechanisms, different chemical and biological analytes, and the expected future technologies. This review is expected to guide the researchers currently working in this field and inspire future generations of scientists to join this compelling research field and its branches.

Research on CdSe/ZnS Quantum Dots-Doped Polymer Fibers and Their Gain Characteristics

Polymer fibers are considered ideal transmission media for all-optical networks, but their high intrinsic loss significantly limits their practical use. Quantum dot-doped polymer fiber amplifiers are emerging as a promising solution to this issue and are becoming a significant focus of research in both academia and industry. Based on the properties of CdSe/ZnS quantum dots and PMMA material, this study experimentally explores three fabrication methods for CdSe/ZnS quantum dots-doped PMMA fibers: hollow fiber filling, melt-drawing, and melt extrusion. The advantages and disadvantages of each method and key issues in fiber fabrication are analyzed. Utilizing the CdSe/ZnS quantum dots-doped PMMA fibers that were fabricated, we theoretically analyzed the key factors affecting gain performance, including fiber length, quantum dots doping concentration, and signal light intensity. Under the conditions of 1.5 W power and 445 nm laser pumping, a maximum on-off gain of 16.2 dB was experimentally achieved at 635 nm. Additionally, using a white light LED as the signal source, a broadband on-off gain with a bandwidth exceeding 70 nm and a maximum gain of 12.4 dB was observed in the 580-650 nm range. This research will contribute to the development of quantum dots-doped fiber devices and broadband optical communication technology, providing more efficient solutions for future optical communication networks.

Direct ink writing 3D-printed optical waveguides for multi-layer interconnect

Low-cost, short-range optical interconnect technology plays an indispensable role in high-speed board-level data communications. In general, 3D printing technology can easily and quickly produce optical components with free-form shapes, while the traditional manufacturing process is complicated and time-consuming. Here, we present a direct ink writing 3D-printing technology to fabricate optical waveguides for optical interconnects. The waveguide core is 3D printed optical polymethylmethacrylate (PMMA) polymer, with propagation loss of 0.21 dB/cm at 980 nm, 0.42 dB/cm at 1310 nm, and 1.08 dB/cm at 1550 nm, respectively. Furthermore, a high-density multilayer waveguide arrays, including a four-layer waveguide arrays with a total of 144 waveguide channels, is demonstrated. Error-free data transmission at 30 Gb/s is achieved for each waveguide channel, indicating that the printing method can produce optical waveguides with excellent optical transmission performance. We believe this simple, low-cost, highly flexible, and environmentally friendly method has great potential for high-speed short-range optical interconnects.

High-resolution fiber imaging for pulsed power experiments

This work presents a novel approach for imaging the visible emissions from plasmas in pulsed power experiments using high-resolution plastic optical fibers. The diagnostic consists of a 2 mm diameter core commercial cable constructed of 13 000 individual acrylic fibers. The fibers are fused together to create a single high-resolution bundle. Different designs were investigated to cover a wide range of resolutions and fields of view (3-700 µm and 0.05-45 mm, respectively). The system was tested on the 1-MA Mykonos accelerator at Sandia National Laboratories and successfully imaged visible emission from a hybrid x-pinch target. Diagnostic development and preliminary results are presented.

Intensity-Modulated Polymer Optical Fiber-Based Refractive Index Sensor: A Review

The simple and highly sensitive measurement of the refractive index (RI) of liquids is critical for designing the optical instruments and important in biochemical sensing applications. Intensity modulation-based polymer optical fiber (POF) RI sensors have a lot of advantages including low cost, easy fabrication and operation, good flexibility, and working in the visible wavelength. In this review, recent developments of the intensity modulation POF-based RI sensors are summarized. The materials of the POF and the working principle of intensity modulation are introduced briefly. Moreover, the RI sensing performance of POF sensors with different structures including tapered, bent, and side-polished structures, among others, are presented in detail. Finally, the sensing performance for different structures of POF-based RI sensors are compared and discussed.

Theoretical Investigation of the Influence of Wavelength on the Bandwidth in Multimode W-Type Plastic Optical Fibers with Graded-Index Core Distribution

The bandwidth of multimode W-type plastic optical fibers (POFs) with graded-index (GI) core distribution is investigated by solving the time-dependent power flow equation. The multimode W-type GI POF is designed from a multimode single-clad (SC) GI POF fiber upon modification of the cladding layer of the latter. Results show how the bandwidth in W-type GI POFs can be enhanced by increasing the wavelength for different widths of the intermediate layer and refractive indices of the outer cladding. These fibers are characterized according to their apparent efficiency to reduce modal dispersion and increase bandwidth.

Fabrication Quality Assessment Based on the Coupling of a Dual-Core Microstructured Polymer Optical Fiber

In this paper we report on the theoretical analysis and fabrication of a dual-core microstructured polymer optical fiber (mPOF) and demonstrate how the coupling characteristics of a dual-core mPOF may be a key factor to assess the quality of the fabrication process. The coupling characteristics of this fiber have been tested and, for comparison purposes, simulations regarding the effects of inaccuracies during the manufacturing process were carried out to evaluate the fabrication quality. Results indicate that theoretical, simulation and experimental data are in good agreement, which highlights the uniformity of the microstructure along the fiber and the quality of its fabrication process. In fact, the manufactured mPOF reached a coupling efficiency up to 95.26%, which makes this mPOF appealing for applications in which highly efficient power couplers are required.

Latest Achievements in Polymer Optical Fiber Gratings: Fabrication and Applications

Grating devices in polymer optical fibers (POFs) have attracted huge interest for many potential applications in recent years. This paper presents the state of the art regarding the fabrication of different types of POF gratings, such as uniform, phase-shifted, tilted, chirped, and long period gratings, and explores potential application scenarios, such as biosensing and optical communications.

Micro and Nanostructured Materials for the Development of Optical Fibre Sensors

The measurement of chemical and biomedical parameters can take advantage of the features exclusively offered by optical fibre: passive nature, electromagnetic immunity and chemical stability are some of the most relevant ones. The small dimensions of the fibre generally require that the sensing material be loaded into a supporting matrix whose morphology is adjusted at a nanometric scale. Thanks to the advances in nanotechnology new deposition methods have been developed: they allow reagents from different chemical nature to be embedded into films with a thickness always below a few microns that also show a relevant aspect ratio to ensure a high transduction interface. This review reveals some of the main techniques that are currently been employed to develop this kind of sensors, describing in detail both the resulting supporting matrices as well as the sensing materials used. The main objective is to offer a general view of the state of the art to expose the main challenges and chances that this technology is facing currently.

Fabrication of Polymer Optical Fibre (POF) Gratings

Gratings inscribed in polymer optical fibre (POF) have attracted remarkable interest for many potential applications due to their distinctive properties. This paper overviews the current state of fabrication of POF gratings since their first demonstration in 1999. In particular we summarize and discuss POF materials, POF photosensitivity, techniques and issues of fabricating POF gratings, as well as various types of POF gratings.

Spectral and spatial characterization of perfluorinated graded-index polymer optical fibers for the distribution of optical wireless communication cells

In this paper, the characterization of a perfluorinated graded-index polymer optical fiber (PF-GIPOF) for a high-bitrate indoor optical wireless system is reported. PF-GIPOF is used here to interconnect different optical wireless access points that distribute optical free-space high-bitrate wireless communication cells. The PF-GIPOF channel is first studied in terms of transmission attenuation and frequency response and, in a second step, the spatial power profile distribution at the fiber output is analyzed. Both characterizations are performed under varying restricted mode launch conditions, enabling us to assess the transmission channel performance subject to potential connectorization errors within an environment where the end users may intervene by themselves on the home network infrastructure.

Review of diverse optical fibers used in biomedical research and clinical practice

Optical fiber technology has significantly bolstered the growth of photonics applications in basic life sciences research and in biomedical diagnosis, therapy, monitoring, and surgery. The unique operational characteristics of diverse fibers have been exploited to realize advanced biomedical functions in areas such as illumination, imaging, minimally invasive surgery, tissue ablation, biological sensing, and tissue diagnosis. This review paper provides the necessary background to understand how optical fibers function, to describe the various categories of available fibers, and to illustrate how specific fibers are used for selected biomedical photonics applications. Research articles and vendor data sheets were consulted to describe the operational characteristics of conventional and specialty multimode and single-mode solid-core fibers, double-clad fibers, hard-clad silica fibers, conventional hollow-core fibers, photonic crystal fibers, polymer optical fibers, side-emitting and side-firing fibers, middle-infrared fibers, and optical fiber bundles. Representative applications from the recent literature illustrate how various fibers can be utilized in a wide range of biomedical disciplines. In addition to helping researchers refine current experimental setups, the material in this review paper will help conceptualize and develop emerging optical fiber-based diagnostic and analysis tools.

Evaluation of modal noise in graded-index silica and plastic optical fiber links for radio over multimode fiber systems

We have evaluated and compared modal noise induced in a graded-index silica multimode fiber (GI-MMF) link and a graded-index plastic optical fiber (GI-POF) link with the misaligned fiber connections. In radio over fiber (RoF) systems using these optical fibers, modal noise appears as unwanted amplitude modulation in the received signal, and results in degradation of the RoF transmission performance. In this work, we have evaluated the modal noise induced in GI-MMFs and GI-POFs with its same core diameter of 50 μm. Our results show that GI-POFs have an inherently higher tolerance to misaligned connection and less modal noise than GI-MMFs in terms of both the error-vector magnitude and the speckle pattern of the transmitted signals.

Characterization of flexible copolymer optical fibers for force sensing applications

In this paper, different polymer optical fibres for applications in force sensing systems in textile fabrics are reported. The proposed method is based on the deflection of the light in fibre waveguides. Applying a force on the fibre changes the geometry and affects the wave guiding properties and hence induces light loss in the optical fibre. Fibres out of three different elastic and transparent copolymer materials were successfully produced and tested. Moreover, the influence of the diameter on the sensing properties was studied. The detectable force ranges from 0.05 N to 40 N (applied on 3 cm of fibre length), which can be regulated with the material and the diameter of the fibre. The detected signal loss varied from 0.6% to 78.3%. The fibres have attenuation parameters between 0.16–0.25 dB/cm at 652 nm. We show that the cross-sensitivies to temperature, strain and bends are low. Moreover, the high yield strength (0.0039–0.0054 GPa) and flexibility make these fibres very attractive candidates for integration into textiles to form wearable sensors, medical textiles or even computing systems.

Efficient group delay averaging in graded-index plastic optical fiber with microscopic heterogeneous core

Intrinsic mode coupling in a graded-index plastic optical fiber (GI POF) is investigated using the developed coupled power theory for a GI POF with a microscopic heterogeneous core. The results showed that the intrinsic material properties can induce random power transitions between all the guided modes, whereas the structural deformation of microbending results in nearest-neighbor coupling. It was numerically demonstrated that efficient group-delay averaging due to intrinsic mode coupling brings the pronounced bandwidth enhancement in fibers with much shorter length than the case of glass multimode fibers.

Optical sensors based on plastic fibers

The recent advances of polymer technology allowed the introduction of plastic optical fiber in sensor design. The advantages of optical metrology with plastic optical fiber have attracted the attention of the scientific community, as they allow the development of low-cost or cost competitive systems compared with conventional technologies. In this paper, the current state of the art of plastic optical fiber technology will be reviewed, namely its main characteristics and sensing advantages. Several measurement techniques will be described, with a strong focus on interrogation approaches based on intensity variation in transmission and reflection. The potential applications involving structural health monitoring, medicine, environment and the biological and chemical area are also presented.