Advances in Metal Halide Perovskite Film Preparation: The Role of Anti-Solvent Treatment

Nitrogen-rich carbon dots as the antisolvent additive for perovskite-based photovoltaic devices

Solution-processed perovskite solar cells (PSCs) have demonstrated a tremendous growth in power conversion efficiency (PCE). A high-quality, defect-free perovskite-based active layer is a key point to enhance PSC performance. Introduction of additives and interlayers have proved to be an effective tool to passivate surface defects, control crystal growth, and improve PSC stability. Antisolvent engineering has emerged recently as a new approach, which aims to adjust perovskite layer properties and enhance the PCE and stability of PSC devices. Here, we demonstrate that carbon dots (CDs) may serve as a prospective additive for antisolvent engineering. Nitrogen-rich amphiphilic CDs were synthesized from amines by a solvothermal method and used as an additive to chlorobenzene for a perovskite layer fabrication. The interaction between perovskite and functional groups in CDs promotes improved crystallization of an active perovskite layer and defects passivation, bringing higher PSCs efficiency, stability, and suppressed hysteresis. Under optimized CD concentration, the maximum PCE increased by 34% due to the improved short-circuit current and fill factor, and the device maintains 87% of its initial efficiency after 6 d of storage under ambient conditions.

Research progress of green antisolvent for perovskite solar cells

Conventional antisolvents such as chlorobenzene and benzotrifluoride are highly toxic and volatile, and therefore not preferred for large-scale fabrication. As such, green antisolvents are favored for the eco-friendly fabrication of perovskite films. This review primarily discusses the impact of various green antisolvents on the fabrication of thin perovskite films and analyzes the main chemical characteristics of these green antisolvents. It also interprets the impact of green antisolvent treatment on crystal growth and nucleation crystallization mechanisms. It introduces the effective fabrication of large-area devices using green antisolvents and analyzes the mechanisms by which green antisolvents enhance device stability. Subsequently, several green antisolvents capable of preparing highly stable and efficient devices are listed. Finally, we outline the key challenges and future prospects of antisolvent treatment. This review paves the way for green fabrication of industrial perovskite solar cells.

Single Crystal Perovskite/Graphene Self-Driven Photodetector with Fast Response Speed

Recently, the combination of two-dimensional (2D) materials and perovskites has gained increasing attention in optoelectronic applications owing to their excellent optical and electrical characteristics. Here, we report a self-driven photodetector consisting of a monolayer graphene sheet and a centimeter-sized CH3NH3PbBr3 single crystal, which was prepared using an optimized wet transfer method. The photodetector exhibits a short response time of 2/30 μs by virtue of its high-quality interface, which greatly enhances electron-hole pair separation in the heterostructure under illumination. In addition, a responsivity of ~0.9 mA/W and a detectivity over 1010 Jones are attained at zero bias. This work inspires new methods for preparing large-scale high-quality perovskite/2D material heterostructures, and provides a new direction for the future enhancement of perovskite optoelectronics.

Anti-Solvent-Free Preparation for Efficient and Photostable Pure-Iodide Wide-Bandgap Perovskite Solar Cells

The perovskite/silicon tandem solar cell (TSC) has attracted tremendous attention due to its potential to breakthrough the theoretical efficiency set for single-junction solar cells. However, the perovskite solar cell (PSC) designed as its top component cell suffers from severe photo-induced halide segregation owing to its mixed-halide strategy for achieving desirable wide-bandgap (1.68 eV). Developing pure-iodide wide-bandgap perovskites is a promising route to fabricate photostable perovskite/silicon TSCs. Here, we report efficient and photostable pure-iodide wide-bandgap PSCs made from an anti-solvent-free (ASF) technique. The ASF process is achieved by mixing two precursor solutions, both of which are capable of depositing corresponding perovskite films without involving anti-solvent. The mixed solution finally forms Cs0.3DMA0.2MA0.5PbI3 perovskite film with a bandgap of 1.68 eV. Furthermore, methylammonium chloride additive is applied to enhance the crystallinity and reduce the trap density of perovskite films. As a result, the pure-iodide wide-bandgap PSC delivers efficiency as high as 21.30 % with excellent photostability, the highest for this type of solar cells. The ASF method significantly improves the device reproducibility as compared with devices made from other anti-solvent methods. Our findings provide a novel recipe to prepare efficient and photostable wide-bandgap PSCs.

Crystallization Kinetics of Perovskite Films by a Green Mixture Antisolvent for Efficient NiOx-Based Inverted Solar Cells

Environment-friendly antisolvents are critical for obtaining highly efficient, reproducible, and sustainable perovskite solar cells (PSCs). Here, we introduced a green mixture antisolvent of ethyl acetate-isopropanol (EA/IPA) to finely regulate the crystal grain growth and related film properties, including the morphology, crystal structure, and chemical composition of the perovskite thin film. The IPA with suitable content in EA plays a key role in achieving a smooth and compact high-quality perovskite thin film, leading to the suppression of film defect-induced nonradiative recombination. As a result, the PSCs based on the EA/IPA (5:1) antisolvent showed a power conversion efficiency of 22.9% with an open-circuit voltage of 1.17 V.

Fabrication and Characterization of a Lead-Free Cesium Bismuth Iodide Perovskite through Antisolvent-Assisted Crystallization

Cesium bismuth iodide perovskite material offers good stability toward ambient conditions and has potential optoelectronic characteristics. However, wide bandgap, absorber surface roughness, and poor surface coverage with pinholes are among the key impediments to its adoption as a photovoltaic absorber material. Herein, bandgap modification and the tailoring of surface morphology have been performed through molar ratio variation and antisolvent treatment, whereby type III antisolvent (toluene) based on Hansen space has been utilized. XRD and Raman spectroscopy analyses confirm the formation of a 0D/2D mixed dimensional structure with improved optoelectronic properties when the molar ratio of CsI/BiI3 was adjusted from 1.5:1 to 1:1.5. The absorption results and Tauc plot determination show that the fabricated film has a lower bandgap of 1.80 eV. TRPL analysis reveals that the film possesses a very low charge carrier lifetime of 0.94 ns, suggesting deep defects. Toluene improves the charge carrier lifetime to 1.89 ns. The average grain size also increases from 323.26 nm to 444.3 nm upon toluene addition. Additionally, the inclusion of toluene results in a modest improvement in PCE, from 0.23% to 0.33%.

Mask-inspired moisture-transmitting and durable thermochromic perovskite smart windows

Thermochromic perovskite smart windows (TPWs) are a cutting-edge energy-efficient window technology. However, like most perovskite-based devices, humidity-related degradation limits their widespread application. Herein, inspired by the structure of medical masks, a unique triple-layer thermochromic perovskite window (MTPW) that enable sufficient water vapor transmission to trigger the thermochromism but effectively repel detrimental water and moisture to extend its lifespan is developed. The MTPW demonstrates superhydrophobicity and maintains a solar modulation ability above 20% during a 45-day aging test, with a decay rate 37 times lower than that of a pristine TPW. It can also immobilize lead ions and significantly reduce lead leakage by 66 times. Furthermore, a significant haze reduction from 90% to 30% is achieved, overcoming the blurriness problem of TPWs. Benefiting from the improved optical performance, extended lifespan, suppressed lead leakage, and facile fabrication, the MTPW pushes forward the wide applications of smart windows in green buildings.

Diffusion-Controlled Crystal Engineering with Diverse Antisolvent Intervention for the Preparation of High-Quality Hybrid Perovskite Films

Antisolvent engineering is routinely used to modulate the crystallization of perovskite films as they can offer an additional driving force for nucleation. Actually, the intervention of antisolvent into nucleation is thought to involve some relatively fast and complex processes, which, however, are not fully understood so far. Here, the diffusion of the organic amine cation FA+ (one dominated precursor) and its distribution in a spin-coating process in different antisolvents is simulated by the computational fluid dynamics (CFD) model. It is suggested that a moderate diffusion rate (like that in the case of toluene as an antisolvent) not only enables to form a very uniform distribution of FA+ ions on the substrate, beneficial to the uniform nucleation of the intermediate phase, but also can balance the nucleation and growth rates of the intermediate phase, thereby suppressing undesired heterogeneous nucleation and growth. Results show that the perovskite film fabricated using toluene as an antisolvent has a high quality, based on which higher power conversion efficiencies of up to 24.32% are achieved for perovskite solar cells.

Ferrocene Derivatives for Improving the Efficiency and Stability of MA-Free Perovskite Solar Cells from the Perspective of Inhibiting Ion Migration and Releasing Film Stress

Further improvement of the performance and stability of inverted perovskite solar cells (PSCs) is necessary for commercialization. Here, ferrocene derivative dibenzoylferrocene (DBzFe) is used as an additive to enhance the performance and stability of MA- and Br- free PSCs. The results show that the introduction of DBzFe not only passivates the defects in the film but also inhibits the ion migration in the film. The final device achieves a power conversion efficiency (PCE) of 23.53%, which is one of the highest efficiencies currently based on self-assembled monolayers (SAMs). Moreover, it maintains more than 96.4% of the original efficiency when running continuously for 400 h at the maximum power point.

High-Efficiency Low-Lead Perovskite Photovoltaics Approaching 20% Enabled by a Vacuum-Drying Strategy

Lead-tin mixed perovskites are excellent photovoltaic materials that can be used in single- or multi-junction perovskite solar cells (PSCs). However, most high-performance Pb-Sn mixed PSCs reported to date are still Pb-dominant. It is highly demanding to develop environmentally friendly low-lead PSCs, but the poor film quality caused by the uncontrollable crystallization kinetics has been hindering the efficiency improvement of low-lead PSCs. Here, a vacuum-drying strategy in the two-step method to fabricate low-lead PSCs (FAPb0.3 Sn0.7 I3 ) with an impressive efficiency of 19.67% is employed. The vacuum treatment induces the formation of low crystalline Pb0.3 Sn0.7 I2 films containing less solvent, thus facilitating the subsequent FAI penetration and suppressing pinholes. Compared with the conventional one-step method, the two-step fabricated low-lead perovskite films with the vacuum-drying treatment exhibit a larger grain size, lower trap density, and weaker recombination loss, thus giving rise to a record-high efficiency near 20% with better thermal stability.

Solid Electrolyte Interphase Formation in Tellurium Iodide Perovskites during Electrochemistry and Photoelectrochemistry

Halide perovskites are promising photoelectrocatalytic materials. Their further development requires understanding of surface processes during electrochemistry. Thin films of tellurium-based vacancy-ordered perovskites with formula A₂TeI₆, A = Cs, methylammonium (MA), were deposited onto transparent conducting substrates using aerosol-assisted chemical vapor deposition. Thin film stability as electrodes and photoelectrodes was tested in dichloromethane containing tetrabutylammonium PF₆ (TBAPF₆). Using photoemission spectroscopy, we show that the formation of a solid electrolyte interphase on the surface of the Cs₂TeI₆, consisting of CsPF₆, enhances the stability of the electrode and allows extended chopped-light chronoamperometry measurements at up to 1.1 V with a photocurrent density of 16 μA/cm². In contrast, (CH₃NH₃)₂TeI₆ does not form a passivating layer and rapidly degrades upon identical electrochemical treatment. This demonstrates the importance of surface chemistry in halide perovskite electrochemistry and photoelectrocatalysis.

Growth of Hybrid Perovskite Crystals from CH3NH3PbI3-xClx Solutions Subjected to Constant Solvent Evaporation Rates

In this work, we subjected hybrid lead-mixed halide perovskite (CH₃NH₃PbI_3-xCl_x) precursor inks to different solvent evaporation rates in order to facilitate the nucleation and growth of perovskite crystals. By controlling the temperature of perovskite solutions placed within open-air rings in precise volumes, we established control over the rate of solvent evaporation and, thus, over both the growth rate and the shape of perovskite crystals. Direct utilization of diluted lead-mixed halide perovskites solutions allowed us to control the nucleation and to favor the growth of only a low number of perovskite crystals. Such crystals exhibited a clear sixfold symmetry. While crystals formed at a lower range of temperatures (40-60 °C) exhibited a more compact dendritic shape, the crystals grown at a higher temperature range (80-110 °C) displayed a fractal dendritic morphology.

Synthetic approaches for perovskite thin films and single-crystals

Halide perovskites are compelling candidates for the next generation of photovoltaic technologies owing to an unprecedented increase in power conversion efficiency and their low cost, facile fabrication and outstanding semiconductor properties.

Highly Sensitive Broadband Phototransistors Based on Gradient Tin/Lead Mixed Perovskites

Highly sensitive broadband photodetectors are critical to numerous cutting-edge technologies such as biomedical imaging, environment monitoring, and night vision. Here, phototransistors based on mixed Sn/Pb perovskites are reported, which demonstrate ultrahigh responsivity, gain and specific detectivity in a broadband from ultraviolet to near-infrared region. The interface properties of the perovskite phototransistors are optimized by a special three-step cleaning-healing-cleaning treatment, leading to a high hole mobility in the channel. The highly sensitive performance of the mixed Sn/Pb perovskite phototransistors can be attributed to the vertical compositional heterojunction automatically formed during the film deposition, which is helpful for the separation of photocarriers thereby enhancing a photogating effect in the perovskite channel. This work demonstrates a convenient approach to achieving high-performance phototransistors through tuning compositional gradient in mixed-metal perovskite channels.

Solar Energy Materials-Evolution and Niche Applications: A Literature Review

The demand for energy has been a global concern over the years due to the ever increasing population which still generate electricity from non-renewable energy sources. Presently, energy produced worldwide is mostly from fossil fuels, which are non-renewable sources and release harmful by-products that are greenhouses gases. The sun is considered a source of clean, renewable energy, and the most abundant. With silicon being the element most used for the direct conversion of solar energy into electrical energy, solar cells are the technology corresponding to the solution of the problem of energy on our planet. Solar cell fabrication has undergone extensive study over the past several decades and improvement from one generation to another. The first solar cells were studied and grown on silicon wafers, in particular single crystals that formed silicon-based solar cells. With the further development in thin films, dye-sensitized solar cells and organic solar cells have significantly enhanced the efficiency of the cell. The manufacturing cost and efficiency hindered further development of the cell, although consumers still have confidence in the crystalline silicon material, which enjoys a fair share in the market for photovoltaics. This present review work provides niche and prominent features including the benefits and prospects of the first (mono-poly-crystalline silicon), second (amorphous silicon and thin films), and third generation (quantum dots, dye synthesized, polymer, and perovskite) of materials evolution in photovoltaics.

Photocatalytic Anaerobic Dehydrogenation of Alcohols over Metal Halide Perovskites: A New Acid-Free Scheme for H2 Production

Photocatalytic H₂ evolution from haloid acid (HX) solution by metal halide perovskites (MHPs) has been intensively investigated; however, the corrosive acid solution severely restricts its practical operability. Therefore, developing acid-free schemes for H₂ evolution using MHPs is highly desired. Here, we investigate the photocatalytic anaerobic dehydrogenation of alcohols over a series of MHPs (APbX₃, A = Cs⁺, CH₃NH₃⁺ (MA), CH(NH₂)₂⁺ (FA); X = Cl^-, Br^-, I^-) to simultaneously produce H₂ and aldehydes. Via the coassembly of Pt and rGO nanosheets on MAPbBr₃ microcrystals, the optimal MAPbBr₃/rGO-Pt reaches a H₂ evolution rate of 3150 μmol g^-1 h^-1 under visible light irradiation (780 nm ≥ λ ≥ 400 nm), which is more than 105-fold higher than pure MAPbBr₃ (30 μmol g^-1 h^-1). The present work not only brings new ample opportunities toward photocatalytic H₂ evolution but also opens up new avenues for more effective utilization of MHPs in photocatalysis.

Additive Engineering in Antisolvent for Widening the Processing Window and Promoting Perovskite Seed Formation in Perovskite Solar Cells

The chlorobenzene (CB) antisolvent is widely used to fabricate high-efficiency perovskite solar cells (PSCs). However, the narrow processing window and the strict volume ratio of a binary mixed solvent limit the fabrication of large-area and high-quality perovskite films. In this work, by systematic investigation of additives with the CB antisolvent, a universal guideline is achieved wherein a small amount of additive with a donor number between 9.0 and 27.0 kcal/mol can significantly widen the antisolvent treating time slot from 2 to 40 s while simultaneously enlarging the processor binary mixed solvent (dimethylformamide/dimethyl sulfoxide) from 7:3 to 0:10. Moreover, this process facilitates the formation of perovskite seeds as templates for perovskite crystal growth, effectively reducing the bulk defects in perovskite films. Finally, the obtained PSCs show remarkable power conversion efficiencies (PCEs) of 22.22 and 19.74% for rigid and flexible devices, respectively.

Efficient and Spectrally Stable Blue Perovskite Light-Emitting Diodes Employing a Cationic π-Conjugated Polymer

Metal halide perovskite semiconductors have demonstrated remarkable potentials in solution-processed blue light-emitting diodes (LEDs). However, the unsatisfied efficiency and spectral stability responsible for trap-mediated non-radiative losses and halide phase segregation remain the primary unsolved challenges for blue perovskite LEDs. In this study, it is reported that a fluorene-based π-conjugated cationic polymer can be blended with the perovskite semiconductor to control film formation and optoelectronic properties. As a result, sky-blue and true-blue perovskite LEDs with Commission Internationale de l'Eclairage coordinates of (0.08, 0.22) and (0.12, 0.13) at the record external quantum efficiencies of 11.2% and 8.0% were achieved. In addition, the mixed halide perovskites with the conjugated cationic polymer exhibit excellent spectral stability under external bias. This result illustrates that π-conjugated cationic polymers have a great potential to realize efficient blue mixed-halide perovskite LEDs with stable electroluminescence.