N,N-Dimethylformamide modulates acid extrusion from murine hepatoma cells

Pathological characteristics of liver injury induced by N,N-dimethylformamide: From humans to animal models

N,N-Dimethylformamide (DMF) is widely used in chemical industries because of its excellent solvent properties. Poisoning accidents caused by DMF have been frequently reported, particularly hepatotoxicity; however, the hepatic pathological changes have rarely been described. This study aimed to summarise the pathological characteristics of the hepatotoxicity associated with DMF in clinical cases and to verify in animal models. Liver pathologies of two patients with liver failure due to DMF were retrospectively analysed. Thirty-six rats were categorised into the DMF group (intraperitoneally injected with 4 g/kg DMF once a week), carbon tetrachloride (CCl₄) group (intraperitoneally injected with 0.5 g/kg CCl₄ twice a week) and control group (intraperitoneally injected with normal saline once a week). The general condition and changes in hepatic pathology at 48 h and 8 weeks were observed. Liver tissues of patients exhibited multiple unevenly distributed inflammatory and fibrotic lesions. The DMF-induced liver injury animal model was successfully established. Inflammation and fibrosis were heterogeneously observed throughout the liver in the DMF group, contrast to entirely homogeneous lesions in the CCl₄ group. Specific hepatic pathological findings (heterogeneous lesions) caused by DMF detected for the first time in humans and animal model, may be significant in the clinical diagnosis of DMF poisoning.

Mechanism of N,N-dimethylformamide electrochemical oxidation using a Ti/RuO2-IrO2 electrode

The compound N,N-dimethylformamide (DMF) is a widely used industrial chemical and a common environmental contaminant that has been found to be harmful to human health. In this study, electrochemical oxidation was adopted for the degradation of DMF. The effects of four kinds of electrodes on the removal rates of DMF and total organic carbon were compared, and based on the result, the Ti/RuO₂–IrO₂ electrode was selected as the operating electrode. The effects of three independent factors (current density, pH, and NaCl proportion) on the DMF degradation were investigated through single-factor experiments, and the experimental results were optimized by response surface methodology. The optimal experimental conditions were obtained as follows: current density = 47 mA cm⁻², pH = 5.5, and NaCl proportion = 15%. The electrochemical oxidation of 50 mg L⁻¹ DMF was performed under the optimal conditions; the degradation rate was 97.2% after 7 h, and the reaction followed the pseudo-first-order kinetic model. The degradation products under optimal conditions and chlorine-free conditions were analyzed, and four degradation pathways were proposed. The DMF degradation was more thorough under optimal conditions.

DEMS as an emerging technology was used to investigate the degradation mechanism of DMF.

Evidence of nigericin as a potential therapeutic candidate for cancers: A review

Emerging studies have shown that nigericin, an H⁺, K⁺ and Pb²⁺ ionophore, has exhibited a promising anti-cancer activity in various cancers. However, its anti-cancer mechanisms have not been fully elucidated. In this review, the recent progresses on the use of nigericin in human cancers have been summarized. By exchanging H⁺ and K⁺ across cell membranes, nigericin shows promising anti-cancer activities in in vitro and in vivo as a single agent or in combination with other anti-cancer drugs through decreasing intracellular pH (pHi). The underlying mechanisms of nigericin also include the inactivation of Wnt/β-catenin signals, blockade of Androgen Receptor (AR) signaling, and activation of Stress-Activated Protein Kinase/c-Jun N-terminal Kinase (SAPK/JNK) signaling pathways. In many cancers, nigericin is proved to specifically target putative Cancer Stem Cells (CSCs), and its synergistic effects on photodynamic therapy are also reported. Other mechanisms of nigericin including influencing the mitochondrial membrane potentials, inducing an increase in drug accumulation and autophagy, controlling insulin accumulation in nuclei, and increasing the cytotoxic activity of liposome-entrapped drugs, are also discussed. Notably, the potential adverse effects such as teratogenic effects, insulin resistance and eryptosis shall not be ignored. Taken together, these reports suggest that treatment of cancer cells with nigericin may offer a novel therapeutic strategy and future potential of translation to clinics.

Integration of proteomics, lipidomics, and metabolomics reveals novel metabolic mechanisms underlying N, N-dimethylformamide induced hepatotoxicity

N, N-Dimethylformamide (DMF) is a universal organic solvent which widely used in various industries, and a considerable amount of DMF is detected in industrial effluents. Accumulating animal and epidemiological studies have identified liver injury as an early toxic effect of DMF exposure; however, the detailed mechanisms remain poorly understood. In this study, we systematically integrated the quantitative proteomics, lipidomics, and metabolomics data obtained from the primary human hepatocytes exposed to DMF, to depict the complicated biochemical reactions correlated to liver damage. Eventually, we identified 284 deregulated proteins (221 downregulated and 63 upregulated) and 149 deregulated lipids or metabolites (99 downregulated and 50 upregulated) induced by DMF exposure. Further, the integration of the protein-metabolite (lipid) interactions revealed that N-glycan biosynthesis (involved in the endoplasmic reticulum stress and the unfolded protein response), bile acid metabolism (involved in the lipid metabolism and the inflammatory process), and mitochondrial dysfunction and glutathione depletion (both contributed to reactive oxygen species) were the typical biochemical reactions disturbed by DMF exposure. In summary, our study identified the versatile protein, lipid, and metabolite molecules in multiple signaling and metabolic pathways involved in DMF induced liver injury, and provided new insights to elucidate the toxic mechanisms of DMF.

Retinoid X receptor α (RXRα)-mediated erythroid-2-related factor-2 (NRF2) inactivation contributes to N,N-dimethylformamide (DMF)-induced oxidative stress in HL-7702 and HuH6 cells

N,N-dimethylformamide (DMF) is a colorless industrial solvent that is frequently used for chemical reactions. Epidemiologic studies and clinical case reports have consistently indicated that the main toxic effect after exposure to DMF is hepatotoxicity. Previous studies have suggested that oxidative stress is the pivotal molecular event of DMF-mediated hepatotoxicity; however, its underlying mechanism remains unclear. In this study, we found that DMF (0-150 mM) exposure induced an increase in reactive oxygen species (ROS) levels and inhibited the transcriptional activity of nuclear factor erythroid-2-related factor-2 (NRF2) in a dose-dependent manner. Subsequently, our research revealed that the elevated ROS levels and the decline in NRF2-mediated anti-oxidative response in HL-7702 and HuH6 cells might be due to the DMF-induced accumulation of retinoid X receptor α (RXRα) protein. Further investigation demonstrated that phosphorylation of the RXRα protein, which is mediated by the activation of extracellular signal-regulated kinase (ERK), leads to the inhibition of RXRα protein degradation and in turn the accumulation of RXRα after DMF exposure. These findings provide information that improves our understanding of the role of RXRα in DMF-induced hepatotoxicity.

Degradation of liquid phase N,N-dimethylformamide by dielectric barrier discharge plasma: Mechanism and degradation pathways

The degradation of liquid phase N,N-dimethylformamide (DMF) using the dielectric barrier discharge (DBD) plasma was studied in the present study. The results showed that 1000 mg L^-1 DMF could be degraded by DBD plasma under different input power, treatment time and initial pH values of aqueous solution. After 40 min with DBD plasma discharge, 52.2% degradation efficiency was achieved at DMF concentration of 1000 mg L^-1 with an input power of 16.19 W under initial pH of 11.14 in aqueous solution, and the energy efficiency of the system was 13.2 mg kJ^-1. The removal efficiency decreased with the presence of radical scavenger, manifesting that •OH plays a critical role in the degradation process. The value of TOC in DMF aqueous solution decreased from 790 mg L^-1 to 507 mg L^-1 in 40 min, which indicated that DBD plasma has the ability to mineralize a portion of DMF in liquid directly. Additionally, the analysis of FTIR, HPLC and the small molecular organic compounds before and after the DBD plasma degradation indicated that the intermediates of DMF in degradation process were N-methylformamide, methanol, formaldehyde and formic acid, which were finally mineralized into ammonia nitrogen, CO₂ and H₂O. Moreover, the possible degradation mechanism and pathways were proposed.

Molecular Mechanism of N,N-Dimethylformamide Degradation in Methylobacterium sp. Strain DM1

N,N-Dimethylformamide (DMF) is one of the most common xenobiotic chemicals, and it can be easily emitted into the environment, where it causes harm to human beings. Herein, an efficient DMF-degrading strain, DM1, was isolated and identified as Methylobacterium sp. This strain can use DMF as the sole source of carbon and nitrogen. Whole-genome sequencing of strain DM1 revealed that it has a 5.66-Mbp chromosome and a 200-kbp megaplasmid. The plasmid pLVM1 specifically harbors the genes essential for the initial steps of DMF degradation, and the chromosome carries the genes facilitating subsequent methylotrophic metabolism. Through analysis of the transcriptome sequencing data, the complete mineralization pathway and redundant gene clusters of DMF degradation were elucidated. The dimethylformamidase (DMFase) gene was heterologously expressed, and DMFase was purified and characterized. Plasmid pLVM1 is catabolically crucial for DMF utilization, as evidenced by the phenotype identification of the plasmid-free strain. This study systematically elucidates the molecular mechanisms of DMF degradation by Methylobacterium IMPORTANCE DMF is a hazardous pollutant that has been used in the chemical industry, pharmaceutical manufacturing, and agriculture. Biodegradation as a method for removing DMF has received increasing attention. Here, we identified an efficient DMF degrader, Methylobacterium sp. strain DM1, and characterized the complete DMF mineralization pathway and enzymatic properties of DMFase in this strain. This study provides insights into the molecular mechanisms and evolutionary advantage of DMF degradation facilitated by plasmid pLVM1 and redundant genes in strain DM1, suggesting the emergence of new ecotypes of Methylobacterium.

Anaerobic treatment of N,N-dimethylformamide-containing high-strength wastewater by submerged anaerobic membrane bioreactor with a co-cultured inoculum

The anaerobic treatment of wastewater containing approximately 2000 mg L^-1N,N-dimethylformamide (DMF) was conducted by a lab-scale submerged anaerobic membrane bioreactor (SAnMBR). The inoculum consisted of aerobic DMF-hydrolyzing activated sludge (DAS) and anaerobic digested sludge (ADS). A rapid start-up was achieved with thorough DMF methanogenic degradation on the first day. The results of a 250-day long-term experiment demonstrated that under a low organic loading rate (OLR) of 3.14-4.16 g COD L^-1 d^-1, SAnMBR maintained excellent DMF removal efficiency along with high methane conversion. However, the elevation of OLR significantly limited DMF hydrolysis. When OLR exceeded 6.54 g COD L^-1 d^-1, both removal efficiency and methane production dramatically dropped. The DMF-hydrolyzing bacteria originating from the DAS gradually decayed under the anaerobic condition, resulting in the weak hydrolysis of DMF. The shortening of hydraulic retention time (HRT) is not recommended for the SAnMBR because severe membrane fouling occurred when HRT was shortened to 8 h. To handle high OLRs, an appropriate solution is to maintain a low F/M ratio by increasing both the influent DMF concentration and sludge concentration. The high CH₄ content in the biogas, exceeding 85%, was shown to be the reason for the suitability of anaerobic treatment to DMF. Some improvements which would help to maintain the effective hydrolysis are proposed: a side-stream system to replenish DAS to the SAnMBR is helpful; slight dosage of nitrate could also help to enrich the DMF-hydrolyzing bacteria; and the co-digestion of DMF and other organics might be convenient to establish a stable DMF-degrading consortium.

Long-term performance of UASB in treating N, N-dimethylformamide-containing wastewater with a rapid start-up by inoculating mixed sludge

Wastewater containing N, N-dimethylformamide (DMF) was treated by artificially mixing the anaerobic granular sludge (AGS) with DMF-degrading activated sludge (DAS) in this study. An up-flow anaerobic sludge blanket (UASB) successfully treated wastewater containing approximately 2000 mg L^-1 DMF during an operation period of 215 days. An inoculation of DAS brought about remarkable results: a rapid start-up with effective DMF methanogenic degradation on the first day, and under a low organic loading rate (OLR) of 1.63-4.22 g COD L^-1 day^-1, the UASB maintained excellent DMF removal efficiency at over 96% along with the high methane production rate (MPR). However, when the OLR increased to 9.24 g COD L^-1 day^-1, DMF removal efficiency and MPR dropped to 47.36% and 1.05 L L^-1 day^-1. A further increase in the OLR to 13.25 g COD L^-1 day^-1 resulted in a sharp deterioration in the DMF-degrading ability, at merely 19.19% and a low MPR of 0.38 L L^-1 day^-1. The excessive elevation of OLR resulted in the insufficient hydrolysis of the DMF, and the further weakening of the conversion from DMF to intermediates and an acceleration the decaying of DMF-hydrolyzing bacteria. Methane-producing archaea was starved of intermediates when hydrolysis was inadequate. Since the DAS can be massively domesticated, and the OLR should be kept lower than 6.17 g COD L^-1 day^-1, the timely replenishing of the DAS to the UASB may be a solution to maintain a stable and effective DMF hydrolysis for long-term operation. The results of this study provide insight for the development of a new concept and an improved method for the effective treatment of wastewater containing degradation-resistant organics.

Characterization and variation of microbial community structure during the anaerobic treatment of N, N-dimethylformamide-containing wastewater by UASB with artificially mixed consortium

A lab-scale UASB was operated successfully to anaerobically treat wastewater containing approximately 2000 mg L^-1N, N-dimethylformamide (DMF) by artificially mixing anaerobic granular sludge with DMF-degrading activated sludge. DMF was effectively degraded by the UASB under a low OLR of 1.63-4.22 g COD L^-1 d^-1, with over 96% DMF removal efficiency and a high methane production rate. However, the DMF-degrading ability gradually weakened along with increases in the OLR. The analysis of the microbial community structure by high-throughput sequencing revealed a decline in the abundance of the facultatively anaerobic DMF-hydrolyzing bacteria originating from activated sludge with increasing OLR, further deteriorating the methanogenic degradation of DMF. When the OLR was lowered again, the slow growth of those facultative anaerobes recovered, and slight improvements in the removal were noted. Methylotrophic methanogens utilized the intermediate products from the hydrolysis of DMF, which kept increasing in abundance throughout the entire experimental period.

Anaerobic treatment of N, N-dimethylformamide-containing wastewater by co-culturing two sources of inoculum

The complete methanogenic degradation of N, N-dimethylformamide (DMF) was achieved in this study. Initially, DMF was found to be feebly degradable by a lab-scale submerged anaerobic membrane bioreactor (SAnMBR) using normal anaerobic digestion sludge (ADS) even after 120-day's culturing. However, aerobic DMF-degrading activated sludge (AS) was rapidly cultivated in a continuous aeration reactor (CAR). A specially designed anaerobic co-cultured sludge (ACS) made by artificially mixing AS with ADS was successfully domesticated by a long term repeated batch experiment. The results demonstrated that ACS could effectively degrade over 5000 mg L^-1 DMF for methane recovery. The metabolic pathway and stoichiometric equation of DMF methanogenic degradation were also revealed and verified in detail. It was confirmed that under the anaerobic condition, with the help of enzyme, DMF converts into dimethylamine and formic acid, and the intermediates are effectively fermented through methylotrophic/hydrogenotrophic methanogenesis. Analysis of the microbial community suggested that some facultatively anaerobic bacteria played the key roles in methanogenic degradation due to their DMF-hydrolyzing ability. By co-culturing two sources of inoculum under the anaerobic condition, the symbiosis of facultatively anaerobic DMF-hydrolyzing bacteria and methylotrophic/hydrogenotrophic methanogens makes methanogenic degradation of DMF available. This study also provides a novel sludge cultivation method for anaerobic treatment of degradation-resistant organics.

Effect of organic loading rate on the removal of DMF, MC and IPA by a pilot-scale AnMBR for treating chemical synthesis-based antibiotic solvent wastewater

This study focuses on the effects of organic loading rate (OLR) on the removal of N,N-Dimethylformamide(DMF), m-Cresol (MC) and isopropyl alcohol (IPA) by a pilot-scale anaerobic membrane bioreactor (AnMBR) for treating chemical synthesis-based antibiotic solvent wastewater at period of improved influent COD concentration with decreased HRT. The whole process was divided into five stages in terms of the variation of OLR ranging from 3.9 to 12.7 kg COD/(m³·d). During 249 days of operating time, the average DMF, MC, IPA removal efficiency were 96.9%,98.2% and 96.4%, respectively. Cake layer was accumulated on the membrane surface acted as a dynamic secondary biofilm which lead to the increase of physical removal rate. In addition, mathematical statistical models was built on the linear regression techniques for exploring the inner relationship between EPS and the performance of the AnMBR.

Dual Effects of N,N-dimethylformamide on Cell Proliferation and Apoptosis in Breast Cancer

N,N-dimethylformamide (DMF) has been widely used as an organic solvent in industries. DMF is a potential medication. However, the antitumorigenic role of DMF in breast cancer remains unclear. Here, we examined dose-dependent effects of DMF on proliferation and apoptosis in breast cancer MCF-7 and nontumorous MCF-12A cells. We found that DMF had a growth inhibitory effect in MCF-12A cells in a dose-dependent manner. By contrast, however, DMF had dual effects on cell proliferation and apoptosis in MCF-7 cells. DMF at a high dose (100 mM) significantly inhibited MCF-7 cell growth while at a low dose (1 mM) significantly stimulated MCF-7 cell growth (both P < .05). The inhibitory effect of DMF on cell proliferation was accompanied by the decrease of cyclin D1 and cyclin E1 protein expression, leading to the cell cycle arrest at the G0/G1 phase. Furthermore, a high-dose DMF significantly increased the number of early apoptotic cells by increasing cleaved caspase-9 and proapoptotic protein Bax expression and decreased the ratio of Bcl-xL/Bax (P < .01). Thus, our data demonstrated for the first time that DMF has dual effects on breast cancer cell behaviors depending upon its dose. Caution must be warranted in determining its effective dose for targeting breast cancer.

An Eco-tank system containing microbes and different aquatic plant species for the bioremediation of N,N-dimethylformamide polluted river waters

An Eco-tank system of 10m was designed to simulate the natural river. It consisted of five tanks sequentially connected containing microbes, biofilm carriers and four species of floating aquatic plants. The purification performance of the system for N,N-dimethylformamide (DMF) polluted river water was evaluated by operating in continuous mode. DMF was completely removed in Tanks 1 and 2 at influent DMF concentrations between 75.42 and 161.05mg L^-1. The NH₄⁺-N concentration increased in Tank 1, followed by a gradual decrease in Tanks 2-5. Removal of NH₄⁺-N was enhanced by aeration. The average effluent NH₄⁺-N concentration of Tank 5 decreased to a minimum of 0.89mg L^-1, corresponding to a decrease of 84.8% when compared with that before aeration. TN concentration did not decrease significantly as expected after inoculation with denitrifying bacteria. The average effluent TN concentration of the system was determined to be 4.58mg L^-1, still unable to satisfy the Class V standard for surface water environmental quality. The results of this study demonstrated that the Eco-tank system is an efficient process in removing DMF, TOC, and NH₄⁺-N from DMF polluted river water. However, if possible, alternative technologies should be adopted for controlling the effluent TN concentration.

Dimethylacetamide-induced occupational toxic hepatitis with a short term recurrence: a rare case report

In recent years, N,N-dimethylacetamide (DMAc) is widely used in the textile and plastics industry as a solvent alternative to more toxic N,N-dimethylformamide (DMF). At home and abroad, sporadic group case reports have revealed that DMAc could cause toxic hepatitis and symptoms or signs indicative of liver involvement among workers exposed to DMAc, with severe cases leading to death. This paper reports a rare case of severe acute toxic hepatitis with a short term recurrence induced by occupational contact with DMAc in a polyimide film factory, as well as in-depth analysis via relevant information and literature.

A novel chemical/biological combined technique for N, N-dimethylformamide wastewater treatment

N, N-Dimethylformamide (DMF) is a widely used organic solvent whose wastewater is difficult to biodegrade directly. In this paper, a novel chemical/biological combined technique consisting of alkaline hydrolysis stripping, activated sludge and a bio-trickling filter (BTF) was developed for DMF wastewater treatment. The main pollutant, DMF, was decomposed to dimethylamine and formate under alkaline conditions, and the dimethylamine was stripped out by the BTF. The pretreated wastewater was then degraded in an activated sludge process. The operation performances of alkaline hydrolysis, activated sludge and BTF processes were investigated separately. At the optimal conditions of an alkali dosage of 40 g/L, an air/liquid ratio of 3000:1 and 5 h in the air-stripping process, the removal of total organic carbon and DMF was found to be 58% and 96%, respectively. A chemical oxygen demand removal efficiency of 80-90% was obtained in the activated sludge process. The performance of BTF was excellent with a dimethylamine removal efficiency close to 90% even at a high loading of 16 g/d.

Generation of continuous packed bed reactor with PVA-alginate blend immobilized Ochrobactrum sp. DGVK1 cells for effective removal of N,N-dimethylformamide from industrial effluents

Effective removal of dimethylformamide (DMF), the organic solvent found in industrial effluents of textile and pharma industries, was demonstrated by using free and immobilized cells of Ochrobactrum sp. DGVK1, a soil isolate capable of utilizing DMF as a sole source of carbon, nitrogen. The free cells have efficiently removed DMF from culture media and effluents, only when DMF concentration was less than 1% (v/v). Entrapment of cells either in alginate or in polyvinyl alcohol (PVA) failed to increase tolerance limits. However, the cells of Ochrobactrum sp. DGVK1 entrapped in PVA-alginate mixed matrix tolerated higher concentration of DMF (2.5%, v/v) and effectively removed DMF from industrial effluents. As determined through batch fermentation, these immobilized cells have retained viability and degradability for more than 20 cycles. A continuous packed bed reactor, generated by using PVA-alginate beads, efficiently removed DMF from industrial effluents, even in the presence of certain organic solvents frequently found in effluents along with DMF.

Biomineralization of N,N-dimethylformamide by Paracoccus sp. strain DMF

N,N-dimethylformamide (DMF) is a man-made compound that is widely used as a solvent for the synthesis of various organic compounds. In this study, a bacterial strain Paracoccus sp. DMF capable of using DMF as the sole carbon, nitrogen and energy source, was isolated from an enrichment culture developed using activated sludge from domestic waste water treatment unit as the source inoculum. The strain DMF was characterized by biochemical tests and 16S rDNA sequence analysis, to be belonging to the genus Paracoccus. Growth on DMF was accompanied with ammonia release and the total organic carbon (TOC) analysis indicated its extensive mineralization. Batch culture studies were conducted in the substrate range of 100-5000 mg L(-1) to determine the biokinetic constants. Strain Paracoccus sp. DMF could tolerate very high concentrations of DMF as the growth was observed even at 15000 mg L(-1). High (micro(max)) and (K(i)) showed the suitability of the strain for the treatment of DMF containing waste water. Transient accumulation of dimethylamine (DMA) in the medium during the growth on DMF and utilization of DMA and monomethylamine (MMA) as growth substrates by Paracoccus sp. strain DMF showed that the pathway of DMF degradation involves DMA and MMA as intermediates, ultimately leading to the formation of carbon dioxide (CO(2)) and ammonia (NH(3)).

A Single Oral Dose of Ethanol Can Alter Transdermal Absorption of Topically Applied Chemicals in Rats

Topical ethanol is used as a dermal penetration enhancer in some commercial products. Previous studies have demonstrated that chronic ethanol consumption can also disrupt skin barrier function, leading to increased transdermal penetration. This observation becomes much more relevant if a single drinking episode induces similar changes. The purpose of this study was thus to examine the transdermal penetration of three model chemicals after acute ethanol consumption. Wistar rats were gavaged with either 10, 6, 4.3, 3, 1.5 g/kg ethanol or saline and allowed to recover for 2 or 24 h. Blood and skin ethanol levels were determined and in vitro penetration experiments performed. The herbicide paraquat, industrial solvent N,N-dimethylformamide (DMF), and insect repellent N,N-diethyl-m-toluamide (DEET) were used as is model chemicals. Absorption was determined and directly compared between ethanol- and saline-treated skin by calculating enhancement ratios. Blood ethanol levels range from 0.25 to 0.015% at 2 h with skin levels at 12-18% of blood values. Ethanol enhances the absorption of paraquat, DMF, and DEET in a dose-dependent fashion. Paraquat and DEET showed no appreciable reduction in enhancement between 2 and 24 h postgavage for the 10-g/kg dose, but DMF did. Enhancement ratios were higher at 24 h for 10 than for 6 g/kg animals, demonstrating a dose-response relationship for recovery time. These studies imply that increased absorption of topical chemical occurs after alcohol ingestion. Both acute and chronic ethanol consumption can compromise the dermal barrier.

Decreased membrane fluidity and hyperpolarization in aluminum-treated PC-12 cells correlates with increased production of cellular oxidants

Effects of aluminum (Al) on membrane properties of excitable cells are not fully understood. Several reports have identified cellular membranes as sensitive targets for Al intoxication. In the present study, we tested the hypothesis that treatment with Al would alter membrane fluidity and potential and these changes would correlate with aberrant generation of cellular oxidants. The effects of in vitro Al exposure in resting rat pheochromocytoma (PC-12) cells, a model that exhibits neuron-like properties, were investigated. Treatment of PC-12 cells with Al (>0.01mM) resulted in a concentration-dependent decrease in membrane fluidity. Similar concentrations of Al increased the rate of extracellular acidification, measured by a cytosensor microphysiometer, indicating stimulation of proton extrusion from cells. This change in proton extrusion was accompanied by a rapid and concentration-dependent hyperpolarizion of the cell membrane as determined by decreased fluorescence of a potential-sensitive dye, bis-[1,3-dibutylbarbituric acid]trimethine oxonol [Dibac(4)(3)]. Al-induced perturbations of membrane properties correlated with an increased level of cellular oxidants, indicated by increasing dihydrorhodamine 123 oxidation. Results suggest that acute exposure to Al modifies membrane properties of neuron-like cells and therefore cellular membranes represent a plausible target for Al neurotoxicity. Alterations in membrane potential can have a dramatic impact on cellular communication especially in neurons and may be an important mechanism in Al neurotoxicity.

Cytosensor techniques for examining signal transduction of neurohormones

This review describes the principles of microphysiometry and how they can be applied, using the Cytosensor, to the investigation of the signal transduction mechanisms activated by both G-protein and non-G-protein coupled hormone and neuropeptide receptors. The use of the Cytosensor to study desensitisation and cross-talk is also discussed, as are the benefits and limitations of this technique.Key words: Cytosensor, microphysiometry, signal transduction, neuropeptides, hormones.