Preparation of molecularly imprinted polymer coated quantum dots to detect nicosulfuron in water samples

ZnS:Mn Quantum Dots Coated with a Silica Molecularly Imprinted Polymer for Trace Teflubenzuron Detection in Vegetable Samples

A novel nanocomposite fluorescent probe consisting of quantum dots and a silica molecularly imprinted polymer (MIPs-capped ZnS:Mn QDs) was synthesized and applied for the rapid detection of teflubenzuron (TBZ) based on the fluorescence quenching of a composite probe via TBZ. The fluorescence quenching efficiency of MIP@SiO2@ZnS:Mn QDs displayed a linear relationship over the concentration range of 0-26.24 μmol/L with a correlation coefficient of 0.9857 and the limit of detection was 2.4 μg/L. The selectivity test showed that the nanocomposite had good selectively rebind TBZ with higher imprinting factor of 3.06 compared with four structurally similar compounds. In addition, the probe was successfully applied to the detection of TBZ in vegetable samples with a recovery of 90.3~97.1% and with a relative standard deviation below 3.2%. This developed method has the advantages of simple preparation, fast response and low toxicity for trace TBZ detection.

Enhanced Molecularly Imprinted Fluorescent Test Strip for Rapid and Visual Detection of Norfloxacin via a Smartphone

Paper-based test strips with on-site visual detection have become a hot spot in the field of target detection. Yet, low specific surface area and uneven deposition limit the further application of test strips. Herein, a novel "turn-on" ratio of molecularly imprinted membranes (Eu@CDs-MIMs) was successfully prepared based on a Eu complex-doped polyvinylidene fluoride membrane for the selective, rapid and on-site visual detection of norfloxacin (NOR). The formation of surface-imprinted polymer-containing carbon dots (CDs) improves the roughness and hydrophilicity of Eu@CDs-MIMs. Fluorescence lifetimes and UV absorption spectra verified that the fluorescence enhancement of CDs is based on the synergistic effect of charge transfer and hydrogen bonding between CDs and NOR. The fluorescent test strip showed a linear fluorescent response within the concentration range of 5-50 nM with a limit of detection of 1.35 nM and a short response time of 1 min. In comparison with filter paper-based test strips, Eu@CDs-MIMs exhibit a brighter and more uniform fluorescent color change from red to blue that is visible to the naked eye. Additionally, the applied ratio fluorescent test strip was combined with a smartphone to translate RGB values into concentrations for the visual and quantitative detection of NOR and verified the detection results using high-performance liquid chromatography. The portable fluorescent test strip provides a reliable approach for the rapid, visual, and on-site detection of NOR and quinolones.

Molecularly imprinted polymers-isolated AuNP-enhanced CdTe QD fluorescence sensor for selective and sensitive oxytetracycline detection in real water samples

A molecularly imprinted polymers (MIPs)-isolated AuNP-enhanced fluorescence sensor, AuNP@MIPs-CdTe QDs, was developed for highly sensitive and selective detection of oxytetracycline (OTC) in aqueous medium. The developed sensor combined the advantages of strong fluorescence signal of metal-enhanced fluorescence (MEF), high selectivity of MIPs, and stability of CdTe QDs. The MIPs shell with specific recognition served as an isolation layer to adjust the distance between AuNP and CdTe QDs to optimize the MEF system. The sensor demonstrated the detection limit as low as 5.22 nM (2.40 μg/L) for a concentration range of 0.1-3.0 μM OTC and good recovery rates of 96.0-103.0% in real water samples. In addition, high specificity recognition for OTC over its analogs was achieved with an imprinting factor of 6.10. Molecular dynamics (MD) simulation was utilized to simulate the polymerization process of MIPs and revealed H-bond formation as the mainly binding sites of APTES and OTC, and finite-difference time-domain (FDTD) analysis was employed to obtain the distribution of electromagnetic field (EM) for AuNP@MIPs-CdTe QDs. The experimental results combined with theoretical analyses not only provided a novel MIP-isolated MEF sensor with excellent detection performance for OTC but also established a theoretical basis for the development of a new generation of sensors.

A fluorescence nanoprobe of N-Acetyl-L-Cysteine capped CdTe QDs for sensitive detection of nitrofurazone

A method was established for detecting the content of nitrofurazone (NFZ) by fluorescence quenching of N-Acetyl-L-Cysteine (NAC) coated cadmium telluride quantum dots (CdTe QDs). By means of transmission electron microscopy (TEM) and multispectral methods such as fluorescence and ultraviolet visible spectra (UV-vis), the synthesized CdTe QDs were characterized. The quantum yield (φ) of CdTe QDs was measured as 0.33 by reference method. The CdTe QDs had a better stability, the RSD of fluorescence intensity was 1.51% in three months. NFZ quenching the emission light of CdTe QDs was observed. The analyses of Stern-Volmer and time-resolved fluorescence suggested the quenching was static. The binding constants (K_a) between NFZ and CdTe QDs were 1.14 × 10⁴ (293 K), 0.74 × 10⁴ (303 K) and 0.51 × 10⁴ (313 K) L mol^-1. The hydrogen bond or van der Waals force was the dominated binding force between NFZ and CdTe QDs. The interaction was further characterized by UV-vis absorption as well as Fourier transform infrared spectra (FT-IR). Using fluorescence quenching effect, a quantitative determination of NFZ was carried out. The optimal experimental conditions were studied and determined as following: pH was 7 and contact time was 10 min. The effects of reagent addition sequence, temperature and the foreign substances including some metals (Mg²⁺; Zn²⁺; Ca²⁺; K⁺; Cu²⁺), glucose, bovine serum albumin (BSA) and furazolidone on the determination were studied. There was a high correlation between the concentration of NFZ (0.40 - 39.63 μg mL^-1) and F₀/F with the standard curve F₀/F = 0.0262c + 0.9910 (r = 0.9994). The detection limit (LOD) reached 0.04 μg mL^-1 (3S₀/S). The contents of NFZ in beef and bacteriostatic liquid were detected. The recovery of NFZ was 95.13% - 103.03% and RSD was 0.66% - 1.37% (n = 5).

Development of immunoassay based on a specific antibody for sensitive detection of nicosulfuron in environment

Nicosulfuron, one of the most widely used selective herbicides in corn field, can effectively control annual and perennial grass weeds, sedges, and some broadleaf weeds. The residual phytotoxicity of nicosulfuron in soil and water has become increasingly prominent. Therefore, an efficient method for detection of nicosulfuron was critical to ensure the sustainable and healthy development of agriculture and the ecological environment. In this paper, five nicosulfuron haptens which contained carboxyl group or aldehyde groups were designed and synthesized, and an indirect competitive immunoassay was developed for the first time. The assay showed an IC50 of 8.42 ng/mL and had negligible cross reactivities toward other sulfonylurea herbicides. In the spike and recovery studies, the recovery rate from soil samples was 95 %-104 %, and that of wheat roots was 92 %-98 %, which showed a good correlation with LC-MS analysis for nicosulfuron. The immunoassay was then used to quantify nicosulfuron concentration which could cause the obvious phytotoxic symptoms to wheat. Obvious symptoms of nicosulfuron phytotoxicity in wheat root was observed at the concentration of 0.068 ± 0.006 mg/kg (ELISA result) which was consistent with 0.072 ± 0.007 mg/kg obtained by LC-MS. The developed immunoassay method is an effective tool for environment contamination monitoring.

Advances in Ultra-small Fluorescence Nanoprobes for Detection of Metal Ions, Drugs, Pesticides and Biomarkers

Identification of trace level chemical species (drugs, pesticides, metal ions and biomarkers) plays key role in environmental monitoring. Recently, fluorescence assay has shown significant advances in detecting of trace level drugs, pesticides, metal ions and biomarkers in real samples. Ultra-small nanostructure materials (metal nanoclusters (NCs), quantum dots (QDs) and carbon dots (CDs)) have been integrated with fluorescence spectrometer for sensitive and selective analysis of trace level target analytes in various samples including environmental and biological samples. This review summarizes the properties of metal NCs and ligand chemistry for the fabrication of metal NCs. We also briefly summarized the synthetic routes for the preparation of QDs and CDs. Advances of ultra-small fluorescent nanosensors (NCs, QDs and CDs) for sensing of metal ions, drugs, pesticides and biomarkers in various sample matrices are briefly discussed. Additionally, we discuss the recent challenges and future perspectives of ultra-small materials as fluorescent sensors for assaying of wide variety of target analytes in real samples.

Molecularly Imprinted Polymer-Coated Inorganic Nanoparticles: Fabrication and Biomedical Applications

Molecularly imprinted polymers (MIPs) continue to gain increasing attention as functional materials due to their unique characteristics such as higher stability, simple preparation, robustness, better binding capacity, and low cost. In particular, MIP-coated inorganic nanoparticles have emerged as a promising platform for various biomedical applications ranging from drug delivery to bioimaging. The integration of MIPs with inorganic nanomaterials such as silica (SiO₂), iron oxide (Fe₃O₄), gold (Au), silver (Ag), and quantum dots (QDs) combines several attributes from both components to yield highly multifunctional materials. These materials with a multicomponent hierarchical structure composed of an inorganic core and an imprinted polymer shell exhibit enhanced properties and new functionalities. This review aims to provide a general overview of key recent advances in the fabrication of MIPs-coated inorganic nanoparticles and highlight their biomedical applications, including drug delivery, biosensor, bioimaging, and bioseparation.

Multivariate Assessment of Procedures for Molecularly Imprinted Polymer Synthesis for Pesticides Determination in Environmental and Agricultural Samples

In the case of quantitative and qualitative analysis of pesticides in environmental and food samples, it is required to perform a sample pre-treatment process. It allows to minimalize the impact of interferences on the final results, as well as increase the recovery rate. Nowadays, apart from routinely employed sample preparation techniques such as solid-phase extraction (SPE) or solid-phase microextraction (SPME), the application of molecularly imprinted polymers (MIPs) is gaining greater popularity. It is mainly related to their physicochemical properties, sorption capacity and selectivity, thermo-mechanical resistance, as well as a wide range of polymerization techniques allowing to obtain the desired type of sorption materials, adequate to a specific type of pesticide. This paper targets to summarize the most popular and innovative strategies since 2010, associated with the MIPs synthesis and analytical procedures for pesticides determination in environmental and food samples. Application of multi-criteria decision analysis (MCDA) allows for visualization of the most beneficial analytical procedures in case of changing the priority of each step of analysis (MIPs synthesis, sample preparation process—pesticides extraction, chromatographic analysis) bearing in mind metrological and environmental issues.

Molecularly Imprinted Polymers (MIPs) in Sensors for Environmental and Biomedical Applications: A Review

Molecular imprinted polymers are custom made materials with specific recognition sites for a target molecule. Their specificity and the variety of materials and physical shapes in which they can be fabricated make them ideal components for sensing platforms. Despite their excellent properties, MIP-based sensors have rarely left the academic laboratory environment. This work presents a comprehensive review of recent reports in the environmental and biomedical fields, with a focus on electrochemical and optical signaling mechanisms. The discussion aims to identify knowledge gaps that hinder the translation of MIP-based technology from research laboratories to commercialization.

Molecularly Imprinted Polymer-Quantum Dot Materials in Optical Sensors: An Overview of Their Synthesis and Applications

In the last decades analytical methods have focused on the determination of target analytes at very low concentration levels. This has been accomplished through the use of traditional analytical methods that usually require high reagent consumption, expensive equipment and long pretreatment steps. Thus, there is a demand for simple, rapid, highly selective and user-friendly detection procedures. Quantum dots (QDs) are semiconductor fluorescent nanomaterials with unique optoelectronic properties that have shown great potential for the development of fluorescence probes. Besides, the combination of QDs with molecularly imprinted polymer (MIPs), synthetic materials with selective recognition, have been proposed as useful materials in the development of optical sensors. The resulting MIP-QDs optical sensors integrate the advantages of both techniques: the high sensitivity of QDs-based fluorescence sensors and the high selectivity of MIPs. This review gives a brief overview of the strategies for the synthesis of MIPs-QDs based optical sensors, highlighting the modifications in the synthesis procedure that improve the sensor performance. Finally, a revision of recent applications in sensing and bioimaging is presented.

A review of the incorporation of QDs and imprinting technology in optical sensors – imprinting methods and sensing responses

This review aims to cover the simultaneous method of using molecularly imprinted technology and quantum dots (QDs) as well as its application in the field of optical sensors.

Mesoporous molecularly imprinted polymer core@shell hybrid silica nanoparticles as adsorbent in microextraction by packed sorbent for multiresidue determination of pesticides in apple juice

In this work, we report the synthesis of a mesoporous molecularly imprinted polymer on the surface of silica nanoparticles (core@mMIP) to be applied as adsorbent in microextraction by packed sorbent (MEPS) for selective determination of pesticides in apple juice. The core@mMIP was properly characterized, showing good adhesion of the polymer to the silica core. The best extraction conditions were: 200 µL of ultrapure water as washing solvent, 150 µL of acetonitrile as eluent, 100 µL of sample at pH 2.5, five draw-eject cycles and 8 mg of adsorbent. Thereby, recoveries of 96.12 ± 1.05%, 76.88 ± 6.18% and 76.18 ± 5.57% were obtained for pyriproxyfen (PPX), deltamethrin (DTM) and etofenprox (ETF), respectively. After validation, the method presented linearity in the range of 0.02-10 µg mL^-1 (r > 0.99), limit of detection of 0.005 µg mL^-1, satisfactory selectivity, and proper precision and accuracy. The method was successfully applied real samples of processed and fresh apple juice.

A fluorescent artificial receptor with specific imprinted cavities to selectively detect colistin

A novel and facile fluorescent artificial receptor on the basis of the molecularly imprinted polymer-coated graphene quantum dots was engineered successfully to detect colistin. The colistin imprinted graphene quantum dots (CMIP-GQDs) was synthesized by vinyl-based radical polymerization between functional monomers and crosslinker at around the template molecule on the surface of graphene quantum dots. The size of bare, CNIP-GQDs, and CMIP-GQDs was about 4.8 ± 0.6 nm, 18.4 ± 1.7 nm, and 19.7 ± 1.3 nm, respectively. The CMIP-GQDs, which showed the strong fluorescence emission at 440 nm with the excitation wavelength fixed at 380 nm, had excellent selectivity and specificity to rapidly recognize and detect colistin. The linear range of fluorescence quenching of this fluorescent artificial receptor for detection colistin was 0.016-2.0 μg mL^-1 with a correlation coefficient (R²) of 0.99919, and the detection limit was 7.3 ng mL^-1 in human serum samples. The designed receptor was successfully applied to detect colistin in human serum samples and it achieved excellent recoveries shifted from 93.8 to 105%. Graphical abstract.

Development of an eco-friendly fluorescence nanosensor based on molecularly imprinted polymer on silica-carbon quantum dot for the rapid indoxacarb detection

Rapid and efficient detection of indoxacarb (IXC), a common chemical contaminant, in environmental and biological samples is necessary. In this work, a modern optical sensor was developed for IXC, based on environmentally friendly molecularly imprinted polymer (MIP) coated on silica-carbon quantum dots (SiCQDs). A hydrothermal method was used to prepare highly fluorescence SiCQDs and, subsequently, MIP formed on surface (MIP@SiCQDs) using a sol-gel method. A linear relationship between the fluorescence quenching effect and increased IXC concentration was found for the range of 4-102 nM, under the optimal conditions, with a 1 nM detection limit. Precisions was of 4.5 and 2.3% for five replicate detections at 21 and 60 nM IXC, respectively. Applicability of the sensor for IXC quantification in environmental and biological samples was verified with recoveries in the range 95-106% with a relative standard deviation of <6.0%.

Application of molecular imprinting polymer anchored on CdTe quantum dots for the detection of sulfadiazine in seawater

A molecularly imprinted polymer (MIP) anchored on the surface of CdTe quantum dots (QDs) was fabricated and used as a fluorescent probe for sulfadiazine (SDZ) detection in seawater. CdTe QDs was used as photoluminescent material, SDZ as the template, 3-aminopropyltriethoxysilane (APTES) as the functional monomer and tetraethyl orthosilicate (TEOS) as the cross-linking agent. Characterizations of MIP-QDs were analyzed by Fourier transform infrared (FT-IR), Transmission electron microscopy (TEM) and Scanning electron microscope (SEM). The conditions were optimized for the detection of MIP-QDs to SDZ. The mechanism of fluorescence quenching was studied by UV-Vis absorption spectroscopy and fluorescence spectroscopy. Under optimal conditions, the fluorescence intensity of MIP-QDs decreased linearly between 4- and 20 μM SDZ with a good correlation coefficient of 0.995. The limit of detection is 0.67 μM and the recovery is between 91.8 and 109.4% with RSD lower than 3.9%. These results indicated that MIP-QDs for SDZ detection in seawater was developed successfully.

Toxicity and serum metabolomics investigation of Mn-doped ZnS quantum dots in mice

Purpose

Mn-doped ZnS quantum dots (QDs) with special luminescent properties have been widely researched and applied in various fields. Thus, their release toxicity and security cannot be ignored.

Methods

In the present study, the toxicity and non-targeted metabolomics of Mn-doped ZnS QDs were investigated after single intravenous injection. Serum metabolites were evaluated based on gas chromatography–mass spectrometry together with multivariate statistical analyses [principal component analysis, partial least squares discriminant analysis, and orthogonal PLS-DA].

Results

The modified metabolites (variable importance in the projection (VIP) >1 and p<0.05) revealed that Mn-doped ZnS QDs exposure disturbed glycolysis, tricarboxylic acid cycle, ketoplasia, glutaminolysis, and amino acid and lipid metabolism. The behavior, coefficients of organs, and histological changes were the same as in the control group, and the disturbance of hematology and serum biochemistry was not dose- or time-dependent.

Conclusion

Our study provides a general observation regarding the toxicity and potential metabolic responses of mice exposed to Mn-doped ZnS QDs.

A nanocomposite probe of polydopamine/molecularly imprinted polymer/quantum dots for trace sarafloxacin detection in chicken meat

A nanooptosensor based on the fluorescence quenching of a composite probe was fabricated for the detection of sarafloxacin. The components of the nanocomposite fluorescent probe were a high affinity material of polydopamine polymer (PDA), a selective material of molecularly imprinted polymer (MIP), and optically sensitive quantum dots (QDs). The developed nanocomposite fluorescent probe exhibited excellent selectivity and sensitivity for sarafloxacin. The molecularly imprinted polymer had an imprinting factor (IF) of 8.18 and produced a probe that quenched fluorescence more effectively than a non-imprinted polymer (NIP) probe. The emission intensity of the MIP probe was linearly quenched by sarafloxacin over a range of 0.10 to 15.0 μg L^-1 with a determination coefficient (R²) of 0.9966. The developed nanooptosensor had a limit of detection of 0.05 μg L^-1. The optosensor detected sarafloxacin in chicken meat samples with recoveries ranging from 82.8 to 99.1% with an RSD below 3%. The found concentrations in spiked samples were compared well with recoveries obtained by HPLC method of detection. This developed nanooptosensor is simple to operate and cost-effective and the analytical procedure is rapid. Graphical abstract.

A nanocomposite fluorescent probe of polyaniline, graphene oxide and quantum dots incorporated into highly selective polymer for lomefloxacin detection

A nanocomposite fluorescent probe based on fluorescence quenching was fabricated and utilized for the detection of lomefloxacin. The fabricated probe integrated the high sensitivity of quantum dots, the excellent selectivity of molecularly imprinted polymer and the high adsorption affinity of graphene oxide and polyaniline. The probe exhibited good sensitivity, high specificity, and rapidity for lomefloxacin monitoring. Fluorescence emission was reduced linearly by lomefloxacin from 0.10 to 50.0 μg L^-1 and the probe exhibited a low limit of detection of 0.07 μg L^-1. The nanooptosensor successfully detected lomefloxacin in milk, chicken meat and egg samples. Recoveries were obtained in the range of 81.5-99.6% and the RSDs were below 7%. The results of this method agreed well with results of HPLC but provided higher sensitivity. This easily fabricated nanocomposite probe could be developed into a highly sensitive and selective optosensor to detect other organic compounds in various complex samples.

Molecularly imprinted polymers' application in pesticide residue detection

Molecularly imprinted polymers (MIPs) are produced using molecular imprinting technology (MIT) and have specific analyte-binding abilities and unique properties, including chemical and thermal stability, reusability, high selectivity, and high sensitivity. The application of MIPs in the detection of pesticides represents an advance and a superior scientific approach owing to their detection and characterization of trace levels in comparison with other methods. In this review, we have summarized the pre-treatment extraction of pesticides with different types of molecularly imprinted polymer for the detection of single and multiple pesticides by elaborating upon their specific extraction efficiency. The importance of different polymerization methods, functional monomers and cross-linkers is highlighted. The aim of this study is to investigate the importance of the application of MIPs in the detection of pesticides and recent advances in the last few years to overcome the limitations of previously developed methods. Existing restrictions and required future aspects are discussed.

A nanocomposite optosensor containing carboxylic functionalized multiwall carbon nanotubes and quantum dots incorporated into a molecularly imprinted polymer for highly selective and sensitive detection of ciprofloxacin

A nanocomposite optosensor consisting of carboxylic acid functionalized multiwall carbon nanotubes and CdTe quantum dots embedded inside a molecularly imprinted polymer (COOH@MWCNT-MIP-QDs) was developed for trace ciprofloxacin detection. The COOH@MWCNT-MIP-QDs were synthesized through a facile sol-gel process using ciprofloxacin as a template molecule, 3-aminopropylethoxysilane as a functional monomer and tetraethoxysilane as a cross-linker at a molar ratio of 1:8:20. The synthesized nanocomposite optosensor had high sensitivity, excellent specificity and high binding affinity to ciprofloxacin. Under optimal conditions, the fluorescence intensity of the optosensor decreased in a linear fashion with the concentration of ciprofloxacin and two linear dynamic ranges were obtained, 0.10-1.0 μg L^-1 and 1.0-100.0 μg L^-1 with a very low limit of detection of 0.066 μg L^-1. The imprinting factors of the two linear range were 17.67 and 4.28, respectively. The developed nanocomposite fluorescence probe was applied towards the determination of ciprofloxacin levels in chicken muscle and milk samples with satisfactory recoveries being obtained in the range of 82.6 to 98.4%. The results were also in good agreement with a HPLC method which indicates that the optosensor can be used as a sensitive, selective and rapid method to detect ciprofloxacin in chicken and milk samples.

Quantum Dots Applied to Methodology on Detection of Pesticide and Veterinary Drug Residues

The pesticide and veterinary drug residues brought by large-scale agricultural production have become one of the issues in the fields of food safety and environmental ecological security. It is necessary to develop the rapid, sensitive, qualitative and quantitative methodology for the detection of pesticide and veterinary drug residues. As one of the achievements of nanoscience, quantum dots (QDs) have been widely used in the detection of pesticide and veterinary drug residues. In these methodology studies, the used QD-signal styles include fluorescence, chemiluminescence, electrochemical luminescence, photoelectrochemistry, etc. QDs can also be assembled into sensors with different materials, such as QD-enzyme, QD-antibody, QD-aptamer, and QD-molecularly imprinted polymer sensors, etc. Plenty of study achievements in the field of detection of pesticide and veterinary drug residues have been obtained from the different combinations among these signals and sensors. They are summarized in this paper to provide a reference for the QD application in the detection of pesticide and veterinary drug residues.

Visual detection of melamine by using a ratiometric fluorescent probe consisting of a red emitting CdTe core and a green emitting CdTe shell coated with a molecularly imprinted polymer

A composite ratiometric fluorescent probe is described for visual detection of melamine (MEL) in milk samples. It is based on the use of red emitting and green emitting CdTe quantum dots, and a mesoporous molecularly imprinted polymer. The red emitting QDs are embedded in the silica microsphere to serve as a core, and the green emitting QDs are coated on the surface of the silica microsphere as a shell. A molecularly imprinted polymer (MIP) with specific recognition sites for MEL was placed on the shell. If MEL is bound by the MIP, the green fluorescence is quenched due to hydrogen bond interaction. The red emission, in contrast, remains unchanged. Quenching leads to a change in the color of fluorescence from red-green to purely red. This effect allows for visual and instrumental detection of MEL. The mesoporous structure of the MIP reduces the mass transfer resistance and enhances the accessibility of sites for MEL. Response is linear in the 50-1000 ng mL^-1 MEL concentration range, and the limit of detection is 13 ng mL^-1. The fluorescent probe was successfully applied to the analysis of MEL-spiked milk samples and gave recoveries between 94.1 and 98.7%, with 3.6-5.1% relative standard deviations. Graphical abstract Schematic of the preparation and detection of the composite probe. The probe was applied for the selective recognition and visual detection of melamine (MEL).

Molecularly imprinted polymers as selective adsorbents for ambient plasma mass spectrometry

The application of molecularly imprinted polymers (MIPs) as molecular scavengers for ambient plasma ionization mass spectrometry has been reported for the first time. MIPs were synthesized using methacrylic acid as functional monomer; nicotine, propyphenazone, or methylparaben as templates; ethylene glycol dimethacrylate as a cross-linker; and 2,2′-azobisisobutyronitrile as polymerization initiator. To perform ambient plasma ionization experiments, a setup consisting of the heated crucible, a flowing atmospheric-pressure afterglow (FAPA) plasma ion source, and a quadrupole ion trap mass spectrometer has been used. The heated crucible with programmable temperature allows for desorption of the analytes from MIPs structure which results in their direct introduction into the ion stream. Limits of detection, linearity of the proposed analytical procedure, and selectivities have been determined for three analytes: nicotine, propyphenazone, and methylparaben. The analytes used were chosen from various classes of organic compounds to show the feasibility of the analytical procedure. The limits of detections (LODs) were 10 nM, 10, and 0.5 μM for nicotine, propyphenazone, and methylparaben, respectively. In comparison with the measurements performed for the non-imprinted polymers, the values of LODs were improved for at least one order of magnitude due to preconcentration of the sample and reduction of background noise, contributing to signal suppression. The described procedure has shown linearity in a broad range of concentrations. The overall time of single analysis is short and requires ca. 5 min. The developed technique was applied for the determination of nicotine, propyphenazone, and methylparaben in spiked real-life samples, with recovery of 94.6–98.4%. The proposed method is rapid, sensitive, and accurate which provides a new option for the detection of small organic compounds in various samples.

Graphical abstract

Selective chemiluminescence method for the determination of trinitrotoluene based on molecularly imprinted polymer-capped ZnO quantum dots

A novel molecularly imprinted polymer (MIP) based chemiluminescence (CL) assay is described for the determination of TNT in environmental samples.

Molecularly imprinted polymers on CdS quantum dots for sensitive determination of cefixime after its preconcentration by magnetic graphene oxide

A sensitive and selective method was developed for the simple monitoring of cefixime based on its preconcentration by magnetic Fe₃O₄@SiO₂modified graphene oxide (Fe₃O₄@SiO₂-GO) and fluorimetric detection using molecularly imprinted polymer coated CdS quantum dots (MIP-CdS QDs).

Fluorescence Probe Based on an Amino-Functionalized Fluorescent Magnetic Nanocomposite for Detection of Folic Acid in Serum

A new fluorescence probe constructed with a multifunctional nanocomposite, Fe₃O₄-ZnS:Mn²⁺/SiO₂-NH₂, was successfully synthesized and then used to detect folic acid in real serum samples. The nanocomposite was characterized by fluorescence spectroscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray powder diffraction, and physical property measurement system. With the addition of analyte, the Fe₃O₄-ZnS:Mn²⁺/SiO₂-NH₂ composite and folic acid formed a new complex because cross-linking of the amino and carboxyl groups participated in the condensation reaction. Then, the energy of quantum dots was transferred to the complex and led to quenching of the fluorescence. Moreover, the fluorescence intensity decreased significantly as the concentration of folic acid increased, and the fluorescence quenching ratio F₀/F was related to the folic acid concentration in the range from 0.1 to 5 μg mL^-1. This method was used for detecting folic acid in real serum samples and gave recoveries in the range of 89.0%-96.0%, with relative standard deviations of 1.2%-3.9%. The detection limit was 9.6 ng mL^-1 (S/N = 3). These satisfactory and simple results showed the great potential of this fluorescence probe in the field of pharmaceutical analysis.

Fluorescence Probe Based on Hybrid Mesoporous Silica/Quantum Dot/Molecularly Imprinted Polymer for Detection of Tetracycline

A newly designed fluorescence probe made from a hybrid quantum dot/mesoporous silica/molecularly imprinted polymer (QD/MS/MIP) was successfully created, and the probe was used for the detection of tetracycline (TC) in serum sample. QD/MS/MIP was characterized by transmission electron microscope, Fourier transform infrared spectroscopy, UV spectroscopy, X-ray powder diffraction, nitrogen adsorption-desorption experiment and fluorescence spectroscopy. Tetracycline, which is a type of broad-spectrum antibiotic, was selected as the template. The monomer and the template were combined by covalent bonds. After the template was removed to form a binding site, a hydrogen bonding interaction formed between the hole and the target molecule. Moreover, when rebinding TC, a new complex was produced between the amino group of QD/MS/MIP and the hydroxyl group of TC. After that, the energy of the QDs could transfer to the complex, which explains the fluorescence quenching phenomenon. The fluorescent intensity of QD/MS/MIP decreased in 10 min, and an excellent linearity from 50 to 1000 ng mL(-1) was correspondingly obtained. This composite material has a high selectivity with an imprinting factor of 6.71. In addition, the confirmed probe strategy was successfully applied to serum sample analyses, and the recoveries were 90.2%-97.2% with relative standard deviations of 2.2%-5.7%. This current work offers a novel and suitable method to synthesize QD/MS/MIP with a highly selective recognition ability. This composite material will be valuable for use in fluorescence probe applications.