Current status of ACL reconstruction in Germany

Mechanical properties of a bioabsorbable magnesium interference screw for anterior cruciate ligament reconstruction in various testing bone materials

Tears of the anterior cruciate ligament (ACL) negatively impact the stability and kinematics of the knee. Interference screws (ISs) are used for graft fixation in ACL reconstruction and provide sufficient fixation strength to withstand the patients' activities during the graft-to-bone integration process. Magnesium is a novel material used to manufacture IS given its strength and bioabsorbability. In previous studies, the selected magnesium IS design showed a better fixation performance in comparison to the conventional IS design due to its shape design and surface condition. In this study, bioabsorbable magnesium ISs were tested for their insertion (insertion torque and a number of turns to implement the IS) and fixation performance (pull-out and dynamic test). To obtain a reliable initial assessment of IS performance, ISs were implanted in 15 per cubic foot (PCF) Sawbones polyurethane foam blocks, Sawbones biomechanical tibia models with 17 PCF foam cores, and human cadaveric tibiae. Porcine tendons were used in the foam block pull-out test, and nylon ropes were used in all other test setups to prevent influences of the ligament graft material itself. In the pull-out test, the graft was subjected to tensile stress at a rate of 6 mm/min. For the dynamic test, 1000 cycles between 0 and 200 N were performed, followed by a final pull-out test. After each test, the tunnel widening pattern was observed by measuring the aspect ratio of the tunnel at the insertion site. The insertion torque lies within the normal insertion torque of the ISs as well as the average ligament tension before the insertion. In the foam block setup, the nylon rope showed a higher pull-out force than the porcine tendon. The comparison of each setup using nylon rope for both pull-out and pull-out after the dynamic test showed no significant difference between the foam block and cadaver setup. However, all tibia model setup shows unexpectedly high pull-out force due to the influence of its cortical layer. There were no statistically significant differences in tunnel widening between foam block-porcine tendon and foam block-nylon rope constructs. The pull-out resistance of magnesium ISs falls within the typical ACL tension range during daily activities. Even though the test results of the magnesium ISs are different in each bone material, the magnesium IS shows adequate fixation ability and workability during insertion without material failure.

"Trends and beliefs in ACL reconstruction surgery: Indian perspectives"

Objectives

The survey aimed to assess trends and beliefs in the management of anterior cruciate ligament reconstruction (ACLR) amongst orthopaedic surgeons in India.

Methods

A survey was created and distributed among the various orthopaedic surgeons from India. The questionnaire included brief details of surgeons and their experience, clinical assessment, management strategies and the rehabilitation protocol.

Results

135 surgeons completed the survey. 35% of them were having experience of more than 12 years. A large number of surgeons were from government academic institutes (35.5%). The most common criteria for deciding about surgery was Clinical evaluation (94.8%). The most common graft choice was hamstring tendon (94%), and suspensory fixation on the femur side and interference screw on the tibial side (80%) is the most common fixation method. Almost two-thirds of surgeons in this survey use bracing to protect ACL graft in the initial phase.

Conclusion

We presented the preferences amongst the group of surgeons on the management of ACL injuries. Hamstring tendon graft remains the most preferred graft for ACL reconstruction. Further, the suspensory loop on the femoral side and interference screw on the tibial side are the preferred fixation method. This group of surgeons is conservative in terms of the timing of surgeries and post-operative bracing. Level of evidence Level V, Expert Opinion.

In Vitro Investigation of the Fixation Performance of a Bioabsorbable Magnesium ACL Interference Screw Compared to a Conventional Interference Screw

An anterior cruciate ligament (ACL) reconstruction is a common treatment for patients with ACL rupture that aims to regain pre-injury knee stability and kinematics. During the ACL reconstruction, one method to fix the graft is the use of an interference screw (IS). The IS should provide initial stability and secure the graft during the healing period. In recent years, magnesium has emerged as an alternative material to permanent metal and polymer ISs. In addition, differences in designs, such as the shape of the IS, can influence the fixation performance of the IS. Therefore, in this biomechanical experiment, two different screw designs with two ligament materials were compared in an insertion and a pull-out test at a rate of 1 mm/s. The screw designs were a conventional polymer screw and a magnesium screw. Porcine tendon and nylon rope were used as ligament materials. All tests were performed in polyurethane foam blocks with 15 PCF density (Synbone AG, Switzerland). As a result, both screw designs required an insertion torque of less than 3 Nm. There was a significant difference between the porcine and nylon rope in pull-out tests for each screw design. The magnesium screw had the highest pull-out force at 412.14 ± 50.00 N for porcine tendon and 707.38 ± 21.81 N for nylon rope. There were no significant differences in tunnel widening (narrow-wide ratio) between each ligament material. The magnesium screw showed the lowest narrow-wide tunnel ratio, implying a better ability to compress the graft to the tunnel. In conclusion, a more optimized magnesium IS design resulted in better graft fixation and an improved ACL reconstruction outcome.

Current trends in anterior cruciate ligament surgery. A worldwide benchmark study

OBJECTIVES

To benchmark current trends on anterior cruciate ligament reconstruction (ACLR) surgery.

METHODS

The largest worldwide ACLR survey to date was performed during May 2020, targeted to reach representation of all continents. It was submitted electronically to all International Society of Arthroscopy, Knee Surgery and Orthopaedic Sports surgeons (n = 3,026), asking those who perform ACLR to respond.

RESULTS

With a final sample size of 2,107, the overall response rate was 69.6%. Median years of practice as orthopaedic surgeon was 15 (range 1-52) and 49.6% of all respondents were defined as high-volume surgeons (>50 ACLR annually). Hamstrings tendon autograft was the preferred graft for primary ACLR (80.3%) and the medial portal femoral drilling was the most frequently used technique (78.5%). Cortical buttons (82.7%) and bioabsorbable screws (62.7%) were the preferred fixation methods for hamstring tendon autograft ACLR in femur and tibia, respectively. Metallic screws (45.2%) were the preferred fixation methods for bone patellar tendon bone autograft in femur and tibia. Most of the respondents routinely used pre-tensioning techniques for their graft preparation (63.8%), but less than half of surgeons preferred antibiotic soaking of the grafts (45.3%). The preferred knee position for graft fixation was 10-30° of knee flexion and neutral rotation (57.0%). The addition of anterolateral augmentation (or extra-articular tenodesis) was infrequent in primary and isolated ACLR (10.0%), but a statistically significant raise was seen for revision surgeries (20.0%). Most used brace in the initial postoperative rehabilitation (54.9%) and the time to allow patients to fully resume sports was at an average of 8.9 ± 2.0 months. Treatment algorithm of paediatric ACL injuries exhibited a low consensus among the respondents.

CONCLUSION

This worldwide survey benchmarks the current trends in ACL reconstruction, achieving the largest participation of surgeons to date. Among the great variety of options available for ACL reconstructions, surgeons' preferences showed some differences according to their location and expertise. Reporting trends in practice, and not only the evidence, is important to medical education and providing patients the safest care possible. This is a Level V, expert opinion study.

High revision arthroscopy rate after ACL reconstruction in men's professional team sports

PURPOSE

The study analysed unique data on anterior cruciate ligament (ACL) injuries among German professional male team sports over five consecutive seasons with the aim of improving medical outcomes in the future. Sport-specific differences in injury occurrence, concomitant injuries, timing of ACL reconstruction, graft type selection and short-term complications were examined.

METHODS

This retrospective study analysed trauma insurance data on all complete ACL tears from players with at least one competitive match appearance in the two highest divisions of German male basketball, ice hockey, football and handball. Each complete ACL tear registered by clubs or physicians between the 2014/15 and 2018/19 seasons with the German statutory accidental insurance for professional athletes (VBG) as part of occupational accident reporting was included.

RESULTS

In total, 189 out of 7517 players (2.5%) sustained an ACL injury, mainly in handball (n = 82; 43.4%) and football (n = 72; 38.1%) followed by ice hockey (n = 20; 10.6%) and basketball (n = 15; 7.9%).Seventeen players (9.0%) also sustained a second ACL injury. Thus, 206 ACL injuries were included in the analysis. The overall match incidence of ACL injuries was 0.5 per 1000 h and was highest in handballs (1.1 injuries per 1000 h). A total of 70.4% of ACL injuries involved concomitant injury to other knee structures, and 29.6% were isolated ACL injuries. The highest rate of isolated ACL injuries was seen in ice hockey (42.9%). All ACL injuries, except for one career-ending injury, required surgery. In the four analysed team sports, hamstring tendons (71.4%) were the most commonly used grafts for ACL reconstruction; football had the highest percentage of alternative grafts (48.7%). During rehabilitation, 22.9% of all surgically treated ACL injuries (n = 205) required at least two surgical interventions, and 15.6% required revision arthroscopy. The main cause of revision arthroscopy (n = 32; 50.0%) was range-of-motion deficit due to arthrofibrosis or cyclops formation.

CONCLUSION

The present study shows an overall high rate of revision arthroscopy after ACLR (15.6%), which should encourage surgeons and therapists to evaluate their treatment and rehabilitation strategies in this specific subpopulation. Hamstring tendon grafts are most commonly used for ACL reconstruction but have the highest revision and infection rates. Handball shows the highest ACL injury risk of the four evaluated professional team sports. Concomitant injuries occur in the majority of cases, with the highest share of isolated ACL injuries occurring in ice hockey.

LEVEL OF EVIDENCE

Level III.

Eccentrically widened bone tunnels after all-inside anterior cruciate ligament reconstruction: a computed tomography and three-dimensional model-based analysis

PURPOSE

To evaluate the extent of tunnel widening after anterior cruciate ligament reconstruction (ACLR) using the all-inside technique and to establish its correlation with patient-reported clinical outcomes and femoral graft bending angle (GBA).

METHODS

Tunnel widening was evaluated using computed tomography (CT)-based three-dimensional (3D) models, and the femoral GBA was directly measured on CT images using the Picture Archiving and Communication System (PACS) software. Clinical follow-up was routine procedure, and patient-reported clinical outcomes mainly included International Knee Documentation Committee (IKDC), Lysholm, and Knee Injury and Osteoarthritis Outcome Scores (KOOS) scores, and subjective knee stability assessment.

RESULTS

Fifty-two patients received standard all-inside ACLR, with a median follow-up of 6 months. Reconstructed anterior cruciate ligaments (ACLs) were scanned during the first 3 days and 6 months after surgery. On both the femoral and tibial sides, bone tunnels were most significantly enlarged at the articular aperture segment; the femoral tunnel was 9.2 ± 1.3 mm postoperatively and was significantly enlarged by 32% to a mean tunnel diameter of 12.1 ± 2.0 mm at 6 months after surgery. Moreover, the extent of tunnel enlargement gradually decreased as the measured levels approached those of the bone cortex. The femoral tunnel center was shifted into the anterior and distal direction, and the tibial tunnel center was shifted into the posterior and lateral direction. Additionally, the mean femoral GBA was 105.9° ± 8.1° at the 6-month follow-up. Tunnel enlargement and GBA were not significantly correlated with patient-reported outcomes.

CONCLUSIONS

Femoral and tibial tunnels were significantly greater and eccentrically shifted at the 6-month follow-up after all-side ACLR. However, the extent of tunnel widening does not markedly affect the short-term clinical outcomes. Meanwhile, the femoral GBA was not significantly correlated with femoral tunnel widening or patient-reported outcomes. Although the tunnel widening following all-inside ACLR was not associated with clinical outcomes, it potentially caused difficulties in revision ACLR.

LEVEL OF EVIDENCE

Level IV.

Preferences in anterior cruciate ligament reconstruction and return to sport: A survey among surgeons in the Netherlands

OBJECTIVE

The purpose of this study was to investigate the preferences of surgeons on technique for femoral tunnel placement, graft selection and criteria for return to sport in the Netherlands.

METHODS

A web-based survey among the Dutch Association of Arthroscopy was conducted.

RESULTS

A total of 125 members (24.0%) were included in the analysis. A total of 87.2% (n = 109) used hamstring autografts for primary ACL reconstruction followed by patellar tendon autograft (n = 11, 8.8%) and quadriceps tendon autograft (n = 5, 4.0%). The anteromedial technique was favored by 50.4% (n = 63), whereas 11.2% (n = 14) of the participants favored the transtibial technique. Return to sport after 9 months of primary ACL reconstruction was allowed by 75.2% (n = 94) of the participants. Regarding criteria to evaluate readiness to return to sport, the surgeons stated postoperative period (n = 107, 85.6%) and functional performance tests (n = 96, 76.8%) as important.

CONCLUSION

The majority of the participants of the Dutch Association of Arthroscopy favored the hamstring autografts for primary anterior cruciate ligament reconstruction. Furthermore, most participants stated postoperative time and functional performance tests as important criteria to evaluate readiness to return to sport. This is the first survey demonstrating a high preference of surgeons to use functional performance tests in the decision-making of readiness to return to sport.

The use of a 3D-printed individualized navigation template to assist in the anatomical reconstruction surgery of the anterior cruciate ligament

Background

To explore the location accuracy and early clinical outcomes of using a 3D-printed individualized navigation template to assist in the reconstruction of the anterior cruciate ligament (ACL).

Methods

A single center randomized control study was conducted. Patients with ACL injury were treated with a conventional operation or an operation assisted by a 3D-printed individualized navigation template (the 3D group). The primary endpoint was the accuracy of the actual reconstruction compared with the planned position.

Results

There were 20 and 23 participants in the conventional group and the 3D group, respectively. There were no differences in the bone tunnel position between the actual postoperative position and the preoperative design in the 3D group (P>0.05). Compared with the 3D group, the positioning of the femoral tunnel was more inferior and shallower in the conventional group (P<0.05). The position of the tibia tunnel was closer to the anterior and medial edge of the tibial platform in the conventional group compared to the 3D group (P<0.05). The intraoperative positioning time was shorter in the 3D group than in the conventional group (3.3±1.0 vs. 5.9±1.8 minutes, P<0.001). The Lysholm and International Knee Documentation Committee scores did not differ between the two groups (P>0.05 for both), and all patients improved after surgery (P<0.001).

Conclusions

The 3D-printed individualized navigation template showed good location accuracy and resulted in reduced intraoperative positioning time compared to the traditional method for ACL reconstruction.

Technical Obstacles for Low-Volume Surgeons in Primary Anterior Cruciate Ligament Reconstruction

A longer surgical time will lead to postoperative complications in orthopaedic surgery. According to previous reports, surgeon volume affects a surgical time in anterior cruciate ligament (ACL) reconstruction. However, little attention has been paid to difference of a surgical time between high- and low-volume surgeons in ACL reconstruction. The purpose of the present study was to investigate the surgical time for both high- and low-volume surgeons and to clarify technical obstacles as well as the important technique to reduce the surgical time in ACL reconstruction. A total of 103 knees in 103 patients with ACL tear were enrolled. All the procedures were performed by 13 different surgeons. The surgeons were divided into two surgeon groups (high- and low-volume groups) based on the number of annual cases. The operative technique was divided into the same five steps to perform comparisons of step-by-step surgical time between the surgeon groups of different volumes. The statistical comparison was done between high- and low-volume groups in terms of surgical time in each step. Total operation times were 87.8 ± 17.6 and 129.9 ± 42.9 minutes in high- and low-volume group, respectively. Low-volume surgeons took much time in tendon harvesting and bone tunnel creation using arthroscopy. Low-volume surgeons took more time for primary ACL reconstruction, especially in tendon harvesting, compared with high-volume surgeons. Tendon harvesting was extremely important, as well as bone tunnel creation, for low-volume surgeons to reduce surgical time in primary ACL reconstruction.

High Risk of Tunnel Convergence in Combined Anterior Cruciate Ligament Reconstruction and Lateral Extra-articular Tenodesis

BACKGROUND

Lateral extra-articular tenodesis (LET) is being increasingly added to primary and revision anterior cruciate ligament (ACL) reconstruction to address residual anterolateral rotatory instability. However, currently there is a lack of knowledge on how close the femoral tunnels are when combining these procedures.

PURPOSE/HYPOTHESES

To assess the risk of tunnel convergence in combined ACL and LET procedures using 2 different surgical techniques (Lemaire and MacIntosh). It was hypothesized that the risk of tunnel convergence would be greater when using the more distally located Lemaire position. The authors further hypothesized that tunnel proximity would be influenced by knee size.

STUDY DESIGN

Controlled laboratory study.

METHODS

Ten fresh-frozen cadaveric knees were used for this study. In each specimen, an anatomic ACL femoral tunnel and 2 LET tunnels were drilled using the Lemaire and MacIntosh positions, respectively. After knee dissection, minimal distances between each ACL and LET tunnel were directly measured on the lateral femoral cortex. Furthermore, computed tomography scans were obtained to measure intertunnel convergence and lateral femoral condyle (LFC) width. On the basis of the average LFC width, knees were divided into large and small knees to determine a relationship between knee size and tunnel convergence.

RESULTS

Convergence of ACL and LET tunnels occurred in 7 of 10 cases (70%) using the Lemaire attachment position. All tunnel collisions occurred directly on the lateral femoral cortex, while intertunnel (intramedullary) conflicts were not observed. Collisions emerged in both small (n = 4) and large (n = 3) knees. Critical tunnel convergence did not occur using the MacIntosh position. The mean minimal distance between the LET and ACL tunnel using the Lemaire and MacIntosh positions was 3.1 ± 4.6 mm and 9.8 ± 5.4 mm, respectively.

CONCLUSION

Tunnel convergence was more frequently observed in combined ACL and LET reconstruction using the Lemaire technique, independent of the knee size. LET femoral tunnel positioning according to the MacIntosh reconstruction was not associated with tunnel collision.

CLINICAL RELEVANCE

These findings help to raise the awareness for the risk of tunnel convergence in combined ACL and LET procedures. Surgeons may contemplate adjustments on the ACL femoral tunnel drilling technique or fixation device when applying an additional Lemaire procedure. However, in the absence of clinical outcome studies comparing different LET techniques, it remains unclear which technique is superior in a clinical setting.

Biomechanical and microbiological effects of local vancomycin in anterior cruciate ligament (ACL) reconstruction: a porcine tendon model

INTRODUCTION

Although there is increasing evidence for the successful use of local vancomycin applied by soaked compresses during ACL reconstruction, there are still little data on its microbiological and biomechanical effects. Furthermore, exact dosage of vancomycin with respect to tendon stability and microbiological effectivity is still unknown.

MATERIALS AND METHODS

63 porcine flexor digitorum profundus tendons were harvested under sterile conditions from fresh cadaver legs. After contamination with Staphylococcus epidermidis (S. epidermidis), tendons were wrapped into sterile compresses moistened with different concentrations of vancomycin for 10 or 20 min. Sterile sodium chloride was used for control. After treatment, tendons were rolled onto blood-agar plates to test for residual bacterial contamination and tested for maximum load and stiffness using a uniaxial testing device with cryo-clamps for tendon fixation. Agar plates were checked after 1 week of culture at 36 °C for signs of bacterial growth.

RESULTS

When applying vancomycin for only 10 min, bacterial contamination was found in all dosage groups ranging from 28.6% contamination (n = 2 of 7 tendons) when using 10 mg/ml up to 85.7% (n = 6 of 7 tendons) when using 1 mg/ml. Applying vancomycin-soaked compresses for 20 min, bacterial contamination was still found in the groups using 1 mg/ml and 2.5 mg/ml (contamination rate 85.7 and 42.9% respectively). When using 5 mg/ml and 10 mg/ml, no bacterial contamination could be perceived after 7 days of culture. With regard to biomechanical properties, no differences were found regarding maximum load or Young's modulus between groups.

CONCLUSIONS

This study showed no signs of biomechanical impairment of porcine flexor tendons after the use of vancomycin wraps with concentration ranging from 1 to 10 mg/ml for 10 or 20 min at a time zero testing. Contamination with S. epidermidis was cleansed in 100% of tendons when using at least 5 mg/ml of vancomycin for 20 min.

Increased medial and lateral tibial posterior slopes are independent risk factors for graft failure following ACL reconstruction

PURPOSE

To analyze the contribution of increased lateral (LTPS) and medial tibial slopes (MTPS) as independent risk factors of graft failure following anterior cruciate ligament (ACL) reconstruction.

MATERIALS AND METHODS

Fifty-seven patients with graft failure after ACL reconstruction who underwent revision surgery between 2009 and 2014 were enrolled and matched to a control group of 69 patients with primary anatomic successful ACL reconstruction. Patients were matched based on age, sex, date of primary surgery and graft type. LTPS and MTPS were measured on MRI in a blinded fashion. Tibial and femoral tunnel positions were determined on CT scans. Independent t test was used to compare the MTPS and LTPS between subgroups. Risks of graft failure associated with an increasing MTPS and LTPS were analyzed using binary logistic analysis.

RESULTS

The means of LTPS (7.3°) and MTPS (6.7°) in the graft failure group were found to be significantly greater than in the control group (4.6° and 4.1°, respectively; p = < 0.001). Non-anatomic and anatomic tunnel positions were found in 42 cases (73.7%) and 15 cases (26.3%), respectively. There were no significant differences in MTPS or LTPS between patients with anatomic and non-anatomic tunnel positions within the graft failure group. An increase of the MTPS of 1° was associated with an 1.24 times increased likelihood of exhibiting graft failure [95% CI 1.07-1.43] (p = 0.003) and an increase of the LTPS of 1° was associated with an 1.17 times increased likelihood of exhibiting graft failure [95% CI 1.04-1.31] (p = 0.009). The increased risk was most evident in patients with a lateral tibial posterior slope of ≥ 10°.

CONCLUSIONS

Increased LTPS and MTPS are independent risk factors for graft failure following ACL reconstruction regardless whether tunnel position is anatomic or non-anatomic. This information may be helpful to clinicians when considering slope correction in selected revision ACL reconstruction procedures.

New Trends in Anterior Cruciate Ligament Reconstruction: A Systematic Review of National Surveys of the Last 5 Years

The purpose of this study was to analyze national surveys of orthopaedic surgeons on anterior cruciate ligament (ACL) reconstruction to determine their preferences related to the preferred graft, femoral tunnel positioning, fixation and tensioning methods, antibiotic and anti-thromboembolic prophylaxis, and use of tourniquet and drains. A systematic search of PubMed, Web of Science, and Cochrane Library was performed. Inclusion criteria were surveys of ACL reconstruction trends and preferences published in the past 5 years (2011–2016), involving members of national societies of orthopaedics. Information regarding survey modalities, population surveyed, graft choice both in the general or in the athletic population, surgical technique, fixation, use of antibiotic, tourniquet, drains, and anti-thromboembolic prophylaxis was extracted. Eight national surveys were included from Europe (three), North or Latin America (three), and Asia (two). Overall, 7,420 questionnaires were sent, and 1,495 participants completed the survey (response rate ranging from 16 to 76.6%). All surveys reported the hamstring tendon (HT) autograft as the preferred graft, ranging from 45 to 89% of the surveyed population, followed by bone-patellar tendon-bone (BPTB) graft (2–41%) and allograft (2–17%). Only two surveys focusing on graft choice in athletic population underlined how in high-demand sportive population the graft choices changes in favor of BPTB. Single-bundle reconstruction was the preferred surgical technique in the four surveys that investigated this issue. Five surveys were in favor of anteromedial (AM) portal and two in favor of trans-tibial technique. Suspension devices for femoral fixation were the preferred choice in all but one survey, while interference screws were the preferred method for tibial fixation. The two surveys that investigated graft tensioning were in favor of manual tensioning. The use of tourniquet, antibiotics, drains, and anti-thromboembolic prophylaxis were vaguely reported. A trend toward the preference of HT autograft was registered in all the surveys; however, sport participation has been highlighted as an important variable for increased use of BPTB. Single-bundle reconstruction with AM portal technique and suspension femoral fixation and screws fixation for the tibia seem the preferred solution. Other variables such as tensioning, antibiotic, anti-thromboembolic prophylaxis, tourniquet use, and drains were investigated scarcely among the surveys; therefore, no clear trends could be delineated. This is a Level V, systematic review of expert opinion study.

High non-anatomic tunnel position rates in ACL reconstruction failure using both transtibial and anteromedial tunnel drilling techniques

INTRODUCTION

Although it is well known from cadaveric and biomechanical studies that transtibial femoral tunnel (TT) positioning techniques are associated with non-anatomic tunnel positions, controversial data exist as so far no clinical differences could have been found, comparing transtibial with anteromedial techniques (AM). The purpose of the study was to analyze if graft failure following TT ACL reconstruction was more commonly associated with non-anatomic tunnel position in comparison with the AM technique. We hypothesized that, compared to AM techniques, non-anatomic tunnel positions correlate with TT tunnel positioning techniques.

MATERIALS AND METHODS

A total of 147 cases of ACL revision surgery were analyzed retrospectively. Primary ACL reconstructions were analyzed regarding the femoral tunnel drilling technique. Femoral and tibial tunnel positions were determined on CT scans using validated radiographic measurement methods. Correlation analysis was performed to determine differences between TT and AM techniques.

RESULTS

A total of 101 cases were included, of whom 64 (63.4%) underwent the TT technique and 37 (36.6%) the AM technique for primary ACL reconstruction. Non-anatomic femoral tunnel positions were found in 77.2% and non-anatomical tibial tunnel positions in 40.1%. No correlations were found comparing tunnel positions in TT and AM techniques, revealing non-anatomic femoral tunnel positions in 79.7 and 73% and non-anatomic tibial tunnel positions in 43.7 and 35.1%, respectively (p > 0.05).

CONCLUSIONS

Considerable rates of non-anatomic femoral and tibial tunnel positions were found in ACL revisions with both transtibial and anteromedial femoral drilling techniques. Despite the potential of placing tunnels more anatomically using an additional AM portal, this technique does not ensure anatomic tunnel positioning. Consequently, the data highlight the importance of anatomic tunnel positioning in primary ACL reconstruction, regardless of the applied drilling technique.