Removing microplastics from wastewater using leading-edge treatment technologies: a solution to microplastic pollution-a review

Microplastic burial potential and ecological risks in mangrove forests of the Amazon River delta

Coastal mangrove ecosystems have been shown to be important microplastic (MP) sinks. Yet, information regarding their MP sequestration capacity is scant. Here, we characterized the spatial and vertical distribution of MPs in mangrove ecosystems of the Amazon River delta and quantified, for the first time, their MP burial and potential economic value related to their surface water filtering capacity. Furthermore, we assessed the ecotoxicological risks considering differing effect mechanisms for benthic organisms (i.e., food dilution and translocation-mediated effects). Soil core samples (up to 3 m) were taken from seven locations in the northern part of the Amazon River delta and analyzed for MP contamination. MPs in the 100-5000 μm range were measured and the polymer type was characterized using Fourier Transform Infrared Spectroscopy. The collected soil samples were dated based on a radionuclide analysis, and a burial analysis was done based on the sediment mass accumulation rates and the mass concentration of MPs. The outcomes of this study show that MPs are ubiquitous contaminants in mangroves of the Amazon River delta (present in 30 out of the 35 analyzed samples). The largest MP concentration was found in the upper soil layer (0-15 cm), 138 MPs/kg dw, which has been deposited and reworked during the time of the soil core collection. However, moderate exposure levels were also found in older samples (71-138 MPs/kg dw), and in samples taken before the plastic era (≈ 1870-1930), suggesting a downward MP migration. We estimated a mean burial rate of 0.32 ± 0.17 kg of MPs km2/year, which corresponds to 0.55 ± 0.28 tons per year in the Amazon River delta. Based on the estimated burial rate, we valued the removal of MPs from surface waters by these mangroves at 0.3-1.1 million USD per year. Our study shows that the exposure levels of MPs in mangroves of the Amazon River delta are relatively low when compared to other mangrove ecosystems and ecotoxicological risks for benthic organisms are not expected given the current exposure levels.

Degradable poly(β-amino ester) microparticles for cleansing products and food fortification

Microplastic pollution is a pressing global crisis caused by the extensive use of nondegradable microplastic materials in daily activities. One effective approach to mitigate this issue is to replace nondegradable plastics with degradable materials that have properties amendable for targeted applications. Here we present the development of a degradable microparticle (MP) platform based on a poly(β-amino ester) (PAE) that degrades into sugar and amino acid derivatives. This PAE MP platform showed functional replacement of nondegradable microplastics used in cleansing products and food fortification. In cleansing products, PAE MPs effectively enhanced the cleansing efficiency of a representative rinse-off product and showed effective removal of potentially toxic elements, as an alternative of traditional nondegradable microbeads. In food fortification, PAE MPs provided robust protection for multiple essential vitamins and minerals against extensive cooking and storage conditions with rapid nutrient release in a simulated human digestion system. Collectively, these PAE MPs present a potential platform to replace microplastic usage on a global scale in many applications.

Optimising microplastics analysis for quantifying and identifying microplastic fibres in laundry wastewater

Current methods for measuring microplastic fibres (MPF) are cumbersome, time consuming and unscalable for routine high throughput analysis. This study reports a method for rapidly extracting, quantifying and analysing MPFs in laundry wastewater with several key improvements which vastly enhance overall efficiency and scalability of analysis. FT-IR surveying is employed as a preliminary step in analysis to quickly determine what polymers are present in a sample prior to fluorescence treatment. Using random quadrating, whole 25 mm filter membranes were surveyed in <30 min with high recovery rates. In industrial laundry wastewater samples, polyester was the most common MPF, however acrylic, nylon, cotton and rayon were all ubiquitous. The study also demonstrates that an excitation wavelength of 365 nm was optimal for fluorescing PET fibres like polyester which were stained with Nile Red, but not 495 nm, which is commonly used in microplastic analysis. Finally, a custom ImageJ macro was written to automatically enumerate and describe MPFs on filter membranes using just a single stitched fluorescence image. In just a few seconds, concentrations of up to 40,000 fibres/L were analysed in industrial laundry wastewater samples with a lower particle size limit of 20 μm. This study highlights the need for more optimised and scalable analysis workflows which maintain high levels of reliability and accuracy.

Microplastics removal in wastewater treatment plants: A review of the different approaches to limit their release in the environment

In last 10 years, the interest about the presence of microplastics (MPs) in the environment has strongly grown. Wastewaters function as a carrier for MPs contamination from source to the aquatic environment, so the knowledge of the fate of this emerging contaminant in wastewater treatment plants (WWTPs) is a priority. This work aims to review the presence of MPs in the influent wastewater (WW) and the effectiveness of the treatments of conventional WWTPs. Moreover, the negative impacts of MPs on the management of the processes have been also discussed. The work also focuses on the possible approaches to tackle MPs contamination enhancing the effectiveness of the WWTPs. Based on literature results, despite WWTPs are not designed for MPs removal from WW, they can effectively remove the MPs (up to 99 % in some references). Nevertheless, they normally act as "hotspots" of MPs contamination considering the remaining concentration of MPs in WWTPs' effluents can be several orders of magnitude higher than receiving waters. Moreover, MPs removed from WW are concentrated in sewage sludge (potentially >65 % of MPs entering the WWTP) posing a concern in case of the potential reuse as a soil improver. This work aims to present a paradigm shift intending WWTPs as key barriers for environmental protection. Approaches for increasing effectiveness against MPs have been discussed in order to define the optimal point(s) of the WWTP in which these technologies should be located. The need of a future legislation about MPs in water and sludge is discussed.

High-throughput microplastic assessment using polarization holographic imaging

Microplastic (MP) pollution has emerged as a global environmental concern due to its ubiquity and harmful impacts on ecosystems and human health. MP assessment has therefore become increasingly necessary and common in environmental and experimental samples. Microscopy and spectroscopy are widely employed for the physical and chemical characterization of MPs. However, these analytical methods often require time-consuming pretreatments of samples or expensive instrumentation. In this work, we develop a portable and cost-effective polarization holographic imaging system that prominently incorporates deep learning techniques, enabling efficient, high-throughput detection and dynamic analysis of MPs in aqueous environments. The integration enhances the identification and classification of MPs, eliminating the need for extensive sample preparation. The system simultaneously captures holographic interference patterns and polarization states, allowing for multimodal information acquisition to facilitate rapid MP detection. The characteristics of light waves are registered, and birefringence features are leveraged to classify the material composition and structures of MPs. Furthermore, the system automates real-time counting and morphological measurements of various materials, including MP sheets and additional natural substances. This innovative approach significantly improves the dynamic monitoring of MPs and provides valuable information for their effective filtration and management.

Single-Particle Analysis of the Photodegradation of Submicron Polystyrene Particles Using Infrared Photothermal Heterodyne Imaging

Sunlight irradiation is the predominant process for degrading plastics in the environment, but our current understanding of the degradation of smaller, submicron (<1000 nm) particles is limited due to prior analytical constraints. We used infrared photothermal heterodyne imaging (IR-PHI) to simultaneously analyze the chemical and morphological changes of single polystyrene (PS) particles (∼1000 nm) when exposed to ultraviolet (UV) irradiation (λ = 250-400 nm). Within 6 h of irradiation, infrared bands associated with the backbone of PS decreased, accompanied by a reduction in the particle size. Concurrently, the formation of several spectral features due to photooxidation was attributed to ketones, carboxylic acids, aldehydes, esters, and lactones. Spectral outcomes were used to present an updated reaction scheme for the photodegradation of PS. After 36 h, the average particle size was reduced to 478 ± 158 nm. The rates of size decrease and carbonyl band area increase were -24 ± 3.0 nm h-1 and 2.1 ± 0.6 cm-1 h-1, respectively. Using the size-related rate, we estimated that under peak terrestrial sunlight conditions, it would take less than 500 h for a 1000 nm PS particle to degrade to 1 nm.

From oceans to dinner plates: The impact of microplastics on human health

Microplastics, measuring less than 5 mm in diameter, are now found in various environmental media, including soil, water, and air, and have infiltrated the food chain, ultimately becoming a part of the human diet. This study offers a comprehensive examination of the intricate nexus between microplastics and human health, thereby contributing to the existing knowledge on the subject. Sources of microplastics, including microfibers from textiles, personal care products, and wastewater treatment plants, among others, were assessed. The study meticulously examined the diverse routes of microplastic exposure-ingestion, inhalation, and dermal contact-offering insights into the associated health risks. Notably, ingestion of microplastics has been linked to gastrointestinal disturbances, endocrine disruption, and the potential transmission of pathogenic bacteria. Inhalation of airborne microplastics emerges as a critical concern, with possible implications for respiratory and cardiovascular health. Dermal contact, although less explored, raises the prospect of skin irritation and allergic reactions. The impacts of COVID-19 on microplastic pollution were also highlighted. Throughout the manuscript, the need for a deeper mechanistic understanding of microplastic interactions with human systems is emphasized, underscoring the urgency for further research and public awareness.

A Complete Guide to Extraction Methods of Microplastics from Complex Environmental Matrices

Sustainable development is a big global challenge for the 21st century. In recent years, a class of emerging contaminants known as microplastics (MPs) has been identified as a significant pollutant with the potential to harm ecosystems. These small plastic particles have been found in every compartment of the planet, with aquatic habitats serving as the ultimate sink. The challenge to extract MPs from different environmental matrices is a tangible and imperative issue. One of the primary specialties of research in environmental chemistry is the development of simple, rapid, low-cost, sensitive, and selective analytical methods for the extraction and identification of MPs in the environment. The present review describes the developments in MP extraction methods from complex environmental matrices. All existing methodologies (new, old, and proof-of-concept) are discussed and evaluated for their potential usefulness to extract MPs from various biotic and abiotic matrices for the sake of progress and innovation. This study concludes by addressing the current challenges and outlining future research objectives aimed at combating MP pollution. Additionally, a set of recommendations is provided to assist researchers in selecting appropriate analytical techniques for obtaining accurate results. To facilitate this process, a proposed roadmap for MP extraction is presented, considering the specific environmental compartments under investigation. By following this roadmap, researchers can enhance their understanding of MP pollution and contribute to effective mitigation strategies.

Unaccounted Microplastics in the Outlet of Wastewater Treatment Plants—Challenges and Opportunities

Since the 1950s, plastic production has skyrocketed. Various environmental and human activities are leading to the formation and accumulation of microplastics (MPs) in aquatic and terrestrial ecosystems, causing detrimental effects on water, soil, plants, and living creatures. Wastewater treatment plants (WWTPs) are one of the primary MP management centers meant to check their entry into the natural systems. However, there are considerable limitations in effectively capturing, detecting, and characterizing these MPs in the inlet and outlet of WWTPs leading to “unaccounted MPs” that are eventually discharged into our ecosystems. In order to assess the holistic picture of the MPs’ distribution in the ecosystems, prevent the release of these omitted MPs into the environment, and formulate regulatory policies, it is vital to develop protocols that can be standardized across the globe to accurately detect and account for MPs in different sample types. This review will cover the details of current WWTP adoption procedures for MP management. Specifically, the following aspects are discussed: (i) several processes involved in the workflow of estimating MPs in the outlet of WWTPs; (ii) key limitations or challenges in each process that would increase the uncertainty in accurately estimating MPs; (iii) favorable recommendations that would lead to the standardization of protocols in the workflow and facilitate more accurate analysis of MPs; (iv) research opportunities to tackle the problem of ‘missing MPs’; and (v) future research directions for the efficient management of MPs. Considering the burgeoning research interest in the area of MPs, this work would help early scientists in understanding the current status in the field of MP analysis in the outlet of WWTPs.

A review of radical and non-radical degradation of amoxicillin by using different oxidation process systems

Pharmaceutical compounds have piqued the interest of researchers due to an increase in their demand, which increases the possibility of leakage into the environment. Amoxicillin (AMX) is a penicillin derivative used for the treatment of infections caused by gram-positive bacteria. AMX has a low metabolic rate in the human body, and around 80-90% is unmetabolized. As a result, AMX residuals should be treated immediately to avoid further accumulation in the environment. Advanced oxidation process techniques are an efficient way to degrade AMX. This review attempts to collect, organize, summarize, and analyze the most up to date research linked to the degradation of AMX by different advanced oxidation process systems including photocatalytic, ultrasonic, electro-oxidation, and advanced oxidation process-based on partials. The main topics investigated in this review are degradation mechanism, degradation efficiency, catalyst stability, the formation of AMX by-products and its toxicity, in addition, the influence of different experimental conditions was discussed such as pH, temperature, scavengers, the concentration of amoxicillin, oxidants, catalyst, and doping ratio. The degradation of AMX could be inhibited by very high values of pH, temperature, AMX concentration, oxidants concentration, catalyst concentration, and doping ratio. Several AMX by-products were discovered after oxidation treatment, and several of them had lower or same values of LC50 (96 h) fathead minnow of AMX itself, such as m/z 384, 375, 349, 323, 324, 321, 318, with prediction values of 0.70, 1.10, 1.10 0.42, 0.42, 0.42, and 0.42 mg/L, respectively. We revealed that there is no silver bullet system to oxidize AMX from an aqueous medium. However, it is recommended to apply hybrid systems such as Photo-electro, Photo-Fenton, Electro-Fenton, etc. Hybrid systems are capable to cover the drawbacks of the single system. This review may provide important information, as well as future recommendations, for future researchers interested in treating AMX using various AOP systems, allowing them to improve the applicability of their systems and successfully oxidize AMX from an aqueous medium.

Bioactive Potential of Brown Algae

Marine-derived natural products are rich source of secondary metabolites with huge potentials including novel therapeutic agents. Marine algae are considered to be a good source of secondary metabolites with versatile bioactivities. During the last few decades, researches related to natural products obtained from brown algae have remarkably escalated as they contain active compounds with varied biologically activities like antimicrobial, anticancer, antioxidant, anti-inflammatory, antidiabetic, and antiparasitic properties. The main bioactive components such as phlorotannin, fucoxanthin, alginic acid, fucoidan, and laminarin have been briefly discussed here, together with their composition and biological activities. In this review, the biological function of extracts and the metabolites of brown algae as well as their pharmacological impacts with the description of the possible mechanism of their action are described and discussed. Also, this study is expected to examine the multifunctional properties of brown algae that facilitate natural algal products, including the ability to integrate these functional properties in a variety of applications.

The Content of Heavy Metals in Cigarettes and the Impact of Their Leachates on the Aquatic Ecosystem

Smoked cigarettes and butts are the most common kind of litter around the world. The buildup of these litters has badly polluted local water bodies and their compartments, and the cumulative effect of many cigarette butts scattered in a centralized location may pose a serious hazard to living species. To understand how heavy metals are leached out into the aquatic ecosystem, researchers must analyse the behavior of the materials that make up cigarettes. Using atomic absorption spectrometry, this study evaluated the content of several metals (such as Cd, Cu, Fe, Pb, Sn, Zn, and Hg) leached from various brands of unsmoked and smoked cigarettes and cigarette butts. The findings revealed that heavy metal is more prevalent in butte. These findings indicate that cigarette litter is a major source of metal contamination in the aquatic ecosystem and that apparent leaching may increase the risk of toxicity to aquatic organisms.