Electrochemical synthesis of a graphene sheet and gold nanoparticle-based nanocomposite, and its application to amperometric sensing of dopamine

Fabrication of a graphite-paraffin carbon paste electrode and demonstration of its use in electrochemical detection strategies

Electrochemical detection methods hold many advantages over their optical counterparts, such as operation in complex sample matrices, low-cost and high volume manufacture and possible equipment miniaturisation. Despite these advantages, the use of electrochemical detection is currently limited in the clinical setting. There is a wide range of potential electrode materials, selected for optimal signal-to-noise ratios and reproducibility when detecting target analytes. The use of carbon paste electrodes (CPEs) for electrochemical detection can be limited by their analytical performance, however they remain very attractive due to their low cost and biocompatibility. This paper presents the fabrication of an easy-to-make and use graphite powder/paraffin wax paste combined with a substrate produced via additive manufacturing and confirms its functionality for both direct and indirect electrochemical measurements. The produced CPEs enable the direct voltammetric detection of hexaammineruthenium(III) chloride and dopamine at an experimental limit of detection (ELoD) of 62.5 μM. The key inflammatory biomarker Interleukin-6 through an enzyme-linked immunosorbant assay (ELISA) was also quantified, yielding a clinically-relevant ELoD of 150 pg ml-1 in 10% human serum. The performance of low-cost and easy-to-use CPEs obtained in 0.5 hours is showcased in this study, demonstrating the platform's potential uses for point-of-need electroanalytical applications.

Gold-Carbon Nanocomposites for Environmental Contaminant Sensing

The environmental crisis, due to the rapid growth of the world population and globalisation, is a serious concern of this century. Nanoscience and nanotechnology play an important role in addressing a wide range of environmental issues with innovative and successful solutions. Identification and control of emerging chemical contaminants have received substantial interest in recent years. As a result, there is a need for reliable and rapid analytical tools capable of performing sample analysis with high sensitivity, broad selectivity, desired stability, and minimal sample handling for the detection, degradation, and removal of hazardous contaminants. In this review, various gold–carbon nanocomposites-based sensors/biosensors that have been developed thus far are explored. The electrochemical platforms, synthesis, diverse applications, and effective monitoring of environmental pollutants are investigated comparatively.

An electrochemical sensor based on gold nanoparticles-functionalized reduced graphene oxide screen printed electrode for the detection of pyocyanin biomarker in Pseudomonas aeruginosa infection

Multidrug resistant Pseudomonas aeruginosa (P. aeruginosa) is known to be a problematic bacterium for being a major cause of opportunistic and nosocomial infections. In this study, reduced graphene oxide decorated with gold nanoparticles (AuNPs/rGO) was utilized as a new sensing material for a fast and direct electrochemical detection of pyocyanin as a biomarker of P. aeruginosa infections. Under optimal condition, the developed electrochemical pyocyanin sensor exhibited a good linear range for the determination of pyocyanin in phosphate-buffered saline (PBS), human saliva and urine at a clinically relevant concentration range of 1-100 μM, achieving a detection limit of 0.27 μM, 1.34 μM, and 2.3 μM, respectively. Our developed sensor demonstrated good selectivity towards pyocyanin in the presence of interfering molecule such as ascorbic acid, uric acid, NADH, glucose, and acetylsalicylic acid, which are commonly found in human fluids. Furthermore, the developed sensor was able to discriminate the signal with and without the presence of pyocyanin directly in P. aeruginosa culture. This proposed technique demonstrates its potential application in monitoring the presence of P. aeruginosa infection in patients.

Recent Advances in Electrochemical and Optical Sensing of Dopamine

Nowadays, several neurological disorders and neurocrine tumours are associated with dopamine (DA) concentrations in various biological fluids. Highly accurate and ultrasensitive detection of DA levels in different biological samples in real-time can change and improve the quality of a patient's life in addition to reducing the treatment cost. Therefore, the design and development of diagnostic tool for in vivo and in vitro monitoring of DA is of considerable clinical and pharmacological importance. In recent decades, a large number of techniques have been established for DA detection, including chromatography coupled to mass spectrometry, spectroscopic approaches, and electrochemical (EC) methods. These methods are effective, but most of them still have some drawbacks such as consuming time, effort, and money. Added to that, sometimes they need complex procedures to obtain good sensitivity and suffer from low selectivity due to interference from other biological species such as uric acid (UA) and ascorbic acid (AA). Advanced materials can offer remarkable opportunities to overcome drawbacks in conventional DA sensors. This review aims to explain challenges related to DA detection using different techniques, and to summarize and highlight recent advancements in materials used and approaches applied for several sensor surface modification for the monitoring of DA. Also, it focuses on the analytical features of the EC and optical-based sensing techniques available.

In-situ graft-crosslinked gold nanoparticles with high-density surface defects and coated with a polytaurine membrane for the voltammetric determination of dopamine

Well-dispersed and graft-crosslinked gold nanoparticles (AuNPs) were synthesized by the reduction of tetrachloroaurate with hydrazine at room temperature. The AuNPs possess a high density of surface defects which is due to grafting of n-octanoic acid to polyvinylpyrrolidone. The physical and chemical properties of the resulting AuNPs were characterized by UV-vis, XRD, TEM/HRTEM, SAED, and XPS, respectively. The modified AuNPs were placed on a glassy carbon electrode (GCE) in an electropolymerized taurine layer to obtain a sensitive, selective, stable and rapid electrochemical dopamine sensor. The peak current, typically measured at 0.17 V (vs. SCE), increases linearly in the 1.0 to 120 μM dopamine concentration range, and the limit of detection (at S/N = 3) is 0.16 μM with a sensitivity of 2.94 μA·μM^-1·cm^-2. The sensor was successfully applied to the determination of dopamine in injections and spiked serum samples. The recoveries from spiked serum samples range from 97.5 to 102.4%, with RSDs ranging between 2.8 and 3.4%. Graphical abstract Schematic representation of a glassy carbon electrode modified with in-situ graft-crosslinked gold nanoparticles combined with an electropolymerized polytaurine membrane. The sensor exhibits excellent features towards dopamine determination.

Ag and Au nanoparticles/reduced graphene oxide composite materials: Synthesis and application in diagnostics and therapeutics

The exceptional electrical, thermal, optical and mechanical properties have made two dimensional sp² hybridized graphene a material of choice in both academic as well as industrial research. In the last few years, researchers have devoted their efforts towards the development of graphene/polymer, graphene/metal nanoparticle and graphene/ceramic nanocomposites. These materials display excellent mechanical, electrical, thermal, catalytic, magnetic and optical properties which cannot be obtained separately from the individual components. Fascinating physical and chemical properties are displayed by noble metal nanomaterials and thus they represent model building blocks for modifying nanoscale structures for diverse applications extending from catalysis, optics to nanomedicine. Insertion of noble metal (Au, Ag) nanoparticles (NPs) into chemically derived graphene is thus of primary importance to open new avenues for both materials in various fields where the specific properties of each material act synergistically to provide hybrid materials with exceptional performances. This review attempts to summarize the different synthetic procedures for the preparation of Ag and Au NPs/reduced graphene oxide (rGO) composites. The synthesis processes of metal NPs/rGO composites are categorised into in-situ and ex-situ techniques. The in-situ approach consists of simultaneous reduction of metal salts and GO to obtain metal NPs/rGO nanocomposite materials, while in the ex-situ process, the metal NPs of desired size and shape are first synthesized and then transferred onto the GO or rGO matrix. The application of the Ag NPs and Au NPs/rGO composite materials in the area of biomedical (drug delivery and photothermal therapy) and biosensing are the focus of this review article.

Electroanalysis of Catecholamine Drugs using Graphene Modified Electrodes

Background:

Catecholamine drugs are a family of electroactive pharmaceutics, which are widely analyzed through electrochemical methods. However, for low level online determination and monitoring of these compounds, which is very important for clinical and biological studies, modified electrodes having high signal to noise ratios are needed. Numerous materials including nanomaterials have been widely used as electrode modifies for these families during the years. Among them, graphene and its family, due to their remarkable properties in electrochemistry, were extensively used in modification of electrochemical sensors.

Objective:

In this review, working electrodes which have been modified with graphene and its derivatives and applied for electroanalyses of some important catecholamine drugs are considered.

Electrochemically reduced graphene oxide and gold nanoparticles on an indium tin oxide electrode for voltammetric sensing of dopamine

The authors describe an electrochemical dopamine sensor that is based on the use of electrochemically co-reduced graphene oxide (Er-GO) and gold nanoparticles (AuNPs) on an indium-tin oxide (ITO) electrode. The synergistic effects of Er-GO and Er-AuNPs promote electron transport in the modified ITO. This results in an excellent performance for voltammetric sensing of dopamine (DA). Under the optimum conditions and a typical working potential of -0.05 V (vs. Ag/AgCl), the ITO electrode has a linear response in the 0.02-200 μM DA concentration range and a low detection limit of 15 nM. The sensor also showed a good selectivity over ascorbic acid and uric acid. The feasibility of the method was studied by analyzing DA in cerebrospinal fluid of rats. Graphical abstract Schematic presentation of one-step electrochemical co-reduction of graphene oxide (GO) and gold nanoparticles (AuNPs) on an ITO electrode for voltammetric sensing of dopamine.

Fluorometric dopamine assay based on an energy transfer system composed of aptamer-functionalized MoS2 quantum dots and MoS2 nanosheets

The authors describe a fluorometric strategy for the determination of dopamine (DA). It is based on the use of aptamer-functionalized MoS₂ quantum dots (QDs) and MoS₂ nanosheets (NSs). The QDs and NSs were extensively characterized with regard to their physical and chemical properties using methods such as TEM, XRD, FT-IR, EDX and molecular spectroscopies. The aptamer against dopamine was labeled with QDs acting as the energy donor in an energy transfer system, while the NSs serve as the energy acceptor. Under the optimal conditions, the fluorescence (FL) intensity (best measured at excitation/emission peaks of 315/412 nm) increases with increasing DA concentration in the range from 0.1 nM to 1000 nM, with a lower detection limit of 45 pM. The method was successfully applied to the determination of DA in complex matrices. In our perception, the method has a wide scope in that it may be extended to other biomolecules for which respective aptamer are available. The QDs show excellent optical properties, good stability, low cytotoxicity, and may also be applied to fluorometric imaging of live cells. Graphical abstract A "turn-on" fluorometric aptasensor for the determination of dopamine (DA) was established based on aptamer-functionalized molybdenum disulfide quantum dots (MoS₂ QDs) and MoS₂ nanosheets. This assay exhibits high selectivity and sensitivity with a detection limit as low as 45 pM.

Development of an Fe3O4@Cu silicate based sensing platform for the electrochemical sensing of dopamine

Abnormal levels of dopamine (DA) in body fluids is an indication of serious health issues, hence development of highly sensitive platforms for the precise detection of DA is highly essential. Herein, we demonstrate an Fe₃O₄@Cu silicate based electrochemical sensing platform for the detection of DA. Morphology and BET analysis shows the formation of ∼320 nm sized sea urchin-like Fe₃O₄@Cu silicate core–shell nanostructures with a 174.5 m² g⁻¹ surface area. Compared to Fe₃O₄ and Fe₃O₄@SiO₂, the Fe₃O₄@Cu silicate urchins delivered enhanced performance towards the electrochemical sensing of DA in neutral pH. The Fe₃O₄@Cu silicate sensor has a 1.37 μA μM⁻¹ cm⁻² sensitivity, 100–700 μM linear range and 3.2 μM limit of detection (LOD). In addition, the proposed Fe₃O₄@Cu silicate DA sensor also has good stability, selectivity, reproducibility and repeatability. The presence of Cu in Fe₃O₄@Cu silicate and the negatively charged surface of the Cu silicate shell play a vital role in achieving high selectivity and sensitivity during DA sensing. The current investigation not only represents the development of a highly selective DA sensor but also directs towards the possibility for the fabrication of other Cu silicate based core–shell nanostructures for the precise detection of DA.

Abnormal levels of dopamine (DA) in body fluids is an indication of serious health issues, hence development of highly sensitive platforms for the precise detection of DA is highly essential.

Multiwalled carbon nanotube supported Schiff base copper complex inorganic nanocomposite for enhanced electrochemical detection of dopamine

A MWCNT/[Cu(sal-ala)bpy] inorganic nanocomposite for the electrochemical detection of dopamine (DA).

Design, Fabrication, Simulation and Characterization of a Novel Dual-Sided Microelectrode Array for Deep Brain Recording and Stimulation

In this paper, a novel dual-sided microelectrode array is specially designed and fabricated for a rat Parkinson’s disease (PD) model to study the mechanisms of deep brain stimulation (DBS). The fabricated microelectrode array can stimulate the subthalamic nucleus and simultaneously record electrophysiological information from multiple nuclei of the basal ganglia system. The fabricated microelectrode array has a long shaft of 9 mm and each planar surface is equipped with three stimulating sites (diameter of 100 μm), seven electrophysiological recording sites (diameter of 20 μm) and four sites with diameter of 50 μm used for neurotransmitter measurements in future work. The performances of the fabricated microelectrode array were characterized by scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. In addition, the stimulating effects of the fabricated microelectrode were evaluated by finite element modeling (FEM). Preliminary animal experiments demonstrated that the designed microelectrode arrays can record spontaneous discharge signals from the striatum, the subthalamic nucleus and the globus pallidus interna. The designed and fabricated microelectrode arrays provide a powerful research tool for studying the mechanisms of DBS in rat PD models.

Graphene-Gold Nanoparticles Hybrid-Synthesis, Functionalization, and Application in a Electrochemical and Surface-Enhanced Raman Scattering Biosensor

Graphene is a single-atom-thick two-dimensional carbon nanosheet with outstanding chemical, electrical, material, optical, and physical properties due to its large surface area, high electron mobility, thermal conductivity, and stability. These extraordinary features of graphene make it a key component for different applications in the biosensing and imaging arena. However, the use of graphene alone is correlated with certain limitations, such as irreversible self-agglomerations, less colloidal stability, poor reliability/repeatability, and non-specificity. The addition of gold nanostructures (AuNS) with graphene produces the graphene-AuNS hybrid nanocomposite which minimizes the limitations as well as providing additional synergistic properties, that is, higher effective surface area, catalytic activity, electrical conductivity, water solubility, and biocompatibility. This review focuses on the fundamental features of graphene, the multidimensional synthesis, and multipurpose applications of graphene-Au nanocomposites. The paper highlights the graphene-gold nanoparticle (AuNP) as the platform substrate for the fabrication of electrochemical and surface-enhanced Raman scattering (SERS)-based biosensors in diverse applications as well as SERS-directed bio-imaging, which is considered as an emerging sector for monitoring stem cell differentiation, and detection and treatment of cancer.

The biogenic synthesis of a reduced graphene oxide–silver (RGO–Ag) nanocomposite and its dual applications as an antibacterial agent and cancer biomarker sensor

Cancer nanotechnology encourages cutting edge research utilizing nanomaterials for the diagnosis, therapy and prevention of cancer.

Ultrafast immunoassays by coupling dielectrophoretic biomarker enrichment in nanoslit channel with electrochemical detection on graphene

Heterogeneous immunoassays usually require long incubation times to promote specific target binding and several wash steps to eliminate non-specific binding. Hence, signal saturation is rarely achieved at detection limit levels of analyte, leading to significant errors in analyte quantification due to extreme sensitivity of the signals to incubation time and methodology. The poor binding kinetics of immunoassays at detection limit levels can be alleviated through creating an enriched analyte plug in the vicinity of immobilized capture probes to enable signal saturation at higher levels and at earlier times, due to higher analyte association and its faster replenishment at the binding surface. Herein, we achieve this by coupling frequency-selective dielectrophoretic molecular dam enrichment of the target biomarker in physiological media to capture probes immobilized on graphene-modified surfaces in a nanoslit to enable ultrafast immunoassays with near-instantaneous (<2 minutes) signal saturation at dilute biomarker levels (picomolar) within ultra-low sample volumes (picoliters). This methodology is applied to the detection of Prostate Specific Antigen (PSA) diluted in serum samples, followed by validation against a standard two-step immunoassay using three de-identified patient samples. Based on the ability of dielectrophoretic molecular dam analyte enrichment methods to enable the detection of PSA at 1-5 pg mL(-1) levels within a minute, and the relative insensitivity of the signals to incubation time after the first two minutes, we envision its application for improving the sensitivity of immunoassays and their accuracy at detection limit levels.

Aptamer-functionalized nanoparticles for surface immobilization-free electrochemical detection of cortisol in a microfluidic device

Monitoring the periodic diurnal variations in cortisol from small volume samples of serum or saliva is of great interest, due to the regulatory role of cortisol within various physiological functions and stress symptoms. Current detection assays are immunologically based and require cumbersome antibody immobilization chemistries, thereby limiting the assay versatility, kinetics, and reproducibility. We present a quantitative aptamer-based detection methodology for cortisol that does not require target labeling, capture probe immobilization on the detection surface or wash steps prior to readout. Using a recognition system of aptamer functionalized gold nanoparticles pre-bound with electro-active triamcinolone, the cortisol level is detected based on its competitive binding to the aptamer by following signal from the displaced triamcinolone using square wave voltammetry at patterned graphene-modified electrodes in a microfluidic or nanoslit device. Due to the 3D analyte diffusion profile at the aptamer interface and the ability to enhance the surface area for cortisol capture, this assay shows signal linearity over a five-log analyte concentration range (10 μg/mL to 30 pg/mL) and exhibits rapid binding kinetics with cortisol versus other glucocorticoids, as apparent from the absence of interferences from estradiol, testosterone and progesterone. The assay is carried out within the biologically relevant range for glucocorticoids in serum and saliva matrices, and benchmarked versus ELISA and radioimmunoassays. Based on absence of cumbersome surface immobilization and wash steps for carrying out this assay, its quantitative signal characteristics and its ability to resist interferences from other glucocorticoids, we envision its application towards routine monitoring of cortisol within bio-fluids.

Stability and binding interaction of bilirubin on a gold nano-surface: steady state fluorescence and FT-IR investigation

A gold nanoparticle exhibits strong absorption and emission due to its unique physical geometry and surface plasmon resonance phenomena. A further modification with organic molecules makes it more appropriate for biological applications. The current manuscript illustrated the optical behavior and stability of bilirubin (BR) coated gold (AuBR) nanoparticles, using BR itself as a reducing agent. In addition, FT-IR and steady state fluorescence measurements were performed to illustrate the binding interaction of BR with the Au(III) ion and the nanoparticles. BR showed a strong affinity towards Au(III) and the measured binding constant was ∼4.3 × 10(5) M(-1). It caused reduction of the Au(III) ion and rendered the formation of cubic face centered AuBR nanoparticles, which were ∼20 nm in diameter. The particles were stabilized as BR was bound to the gold nanoparticle surface, which was confirmed by FT-IR measurement. An intense carboxyl C=O stretching vibration at 1695 cm(-1) was observed for the BR powder but was absent for the AuBR nanoparticles. However, two weak bands at ∼1563 and 1391 cm(-1), presumably due to the asymmetric and symmetric stretching vibrations of the carboxylate form (COO(-)), were found for the AuBR nanoparticles. A stretching vibration of lactam C[double bond, length as m-dash]O appeared at 1645 cm(-1) for BR and the band was shifted to 1647 cm(-1) for the AuBR nanoparticles. The stretching modes of pyrrole N-H and lactam N-H were detected at 3406 cm(-1) and 3267 cm(-1), respectively, for BR. However, the pyrrole N-H band shifted to 3446 cm(-1) and became broader for the AuBR nanoparticles. The observed blue shift in the lactam C[double bond, length as m-dash]O and N-H vibrations of the AuBR nanoparticles indicated a weakening/absence of internal hydrogen bonds between the carboxyl groups and the four N-H bonds in the BR moiety. The binding of BR to the surface provides great stability to the nanoparticles, which remained monodispersed in the large pH range (pH 4 to 12) for more than a month. However, under acidic pH conditions the particles associated to form bigger particles and the plasmon resonance band shifted as they grew; the plasmon resonance band shifted from 525 nm (at pH 7.0) to 555 nm (at pH 3.0). The particles also remained stable in the presence of a higher concentration of salt (KCl and NaCl) in the dispersing media.

Amplified electrochemical genotyping of single-nucleotide polymorphisms using a graphene–gold nanoparticles modified glassy carbon platform

A triple signal amplification strategy for the single nucleotide polymorphisms (SNPs) genotyping is reported using the graphene–gold nanoparticles (GR–AuNPs) as a sensitive platform and monobase-modified silver and gold nanoparticles (M-NPs).

Graphene and its nanocomposite material based electrochemical sensor platform for dopamine

In this review, the recent progress in the electrochemical sensing of dopamine with various graphene and their nanocomposite materials modified electrodes are presented.