Continuous differential impedance spectroscopy of single cells

Label-free differentiation of living versus dead single yeast cells using broadband electrical impedance spectroscopy

The use of the intrinsic electrical properties of a single cell by broadband electrical impedance spectroscopy (EIS) as a label-free and non-invasive method to monitor cellular and intracellular features is an emerging field. Here, we present a novel EIS-based sheathless microfluidic platform with an integrated coplanar waveguide to probe the interior of a single cell. This platform allows for precise single-cell trapping by dielectrophoresis, hydrodynamic focusing, and sensing the electrical properties of the trapped single cell. We measured the impedance characteristics of a single Schizosaccharomyces pombe (fission) yeast cell by a single frequency sweep (30 kHz to 6GHz) in a stagnant sucrose solution using two-port scattering (S) parameters. The measurements revealed a clear distinction between the cytoplasm impedance of live versus dead cells at 3 GHz. This platform could provide real-time monitoring of cellular electrical responses to chemical and physical antagonists for diagnostic purposes.

Full-electric microfluidic platform to capture, analyze and selectively release single cells

Current single-cell technologies require large and expensive equipment, limiting their use to specialized labs. In this paper, we present for the first time a microfluidic device which demonstrates a combined method for full-electric cell capturing, analyzing, and selectively releasing with single-cell resolution. All functionalities are experimentally demonstrated on Saccharomyces cerevisiae. Our microfluidic platform consists of traps centered around a pair of individually accessible coplanar electrodes, positioned under a microfluidic channel. Using this device, we validate our novel Two-Voltage method for trapping single cells by positive dielectrophoresis (pDEP). Cells are attracted to the trap when a high voltage (VH) is applied. A low voltage (VL) holds the already trapped cell in place without attracting additional cells, allowing full control over the number of trapped cells. After trapping, the cells are analyzed by broadband electrochemical impedance spectroscopy. These measurements allow the detection of single cells and the extraction of cell parameters. Additionally, these measurements show a strong correlation between average phase change and cell size, enabling the use of our system for size measurements in biological applications. Finally, our device allows selectively releasing trapped cells by turning off the pDEP signal in their trap. The experimental results show the techniques potential as a full-electric single-cell analysis tool with potential for miniaturization and automation which opens new avenues towards small-scale, high throughput single-cell analysis and sorting lab-on-CMOS devices.

Concepts, electrode configuration, characterization, and data analytics of electric and electrochemical microfluidic platforms: a review

Microfluidic cytometry (MC) and electrical impedance spectroscopy (EIS) are two important techniques in biomedical engineering. Microfluidic cytometry has been utilized in various fields such as stem cell differentiation and cancer metastasis studies, and provides a simple, label-free, real-time method for characterizing and monitoring cellular fates. The impedance microdevice, including impedance flow cytometry (IFC) and electrical impedance spectroscopy (EIS), is integrated into MC systems. IFC measures the impedance of individual cells as they flow through a microfluidic device, while EIS measures impedance changes during binding events on electrode regions. There have been significant efforts to improve and optimize these devices for both basic research and clinical applications, based on the concepts, electrode configurations, and cell fates. This review outlines the theoretical concepts, electrode engineering, and data analytics of these devices, and highlights future directions for development.

A review of bio-impedance devices

Bio-impedance measurement analysis primarily refers to a safe and a non-invasive technique to analyze the electrical changes in living tissues on the application of low-value alternating current. It finds applications both in the biomedical and the agricultural fields. This paper concisely reviews the origin and measurement approaches for concepts and fundamentals of bio-impedance followed by a critical review on bio-impedance portable devices with main emphasis on the embedded system approach which is in demand due to its miniature size and present lifestyle preference of monitoring health in real time. The paper also provides a comprehensive review of various bio-impedance circuits with emphasis on the measurement and calibration techniques.

Recent Advances in Electrical Impedance Sensing Technology for Single-Cell Analysis

Cellular heterogeneity is of significance in cell-based assays for life science, biomedicine and clinical diagnostics. Electrical impedance sensing technology has become a powerful tool, allowing for rapid, non-invasive, and label-free acquisition of electrical parameters of single cells. These electrical parameters, i.e., equivalent cell resistance, membrane capacitance and cytoplasm conductivity, are closely related to cellular biophysical properties and dynamic activities, such as size, morphology, membrane intactness, growth state, and proliferation. This review summarizes basic principles, analytical models and design concepts of single-cell impedance sensing devices, including impedance flow cytometry (IFC) to detect flow-through single cells and electrical impedance spectroscopy (EIS) to monitor immobilized single cells. Then, recent advances of both electrical impedance sensing systems applied in cell recognition, cell counting, viability detection, phenotypic assay, cell screening, and other cell detection are presented. Finally, prospects of impedance sensing technology in single-cell analysis are discussed.

Monitoring Single S. cerevisiae Cells with Multifrequency Electrical Impedance Spectroscopy in an Electrode-Integrated Microfluidic Device

This chapter describes an electrode-integrated microfluidic system with multiple functions of manipulating and monitoring single S. cerevisiae cells. In this system, hydrodynamic trapping and negative dielectrophoretic (nDEP) releasing of S. cerevisiae cells are implemented, providing a flexible method for single-cell manipulation. The multiplexing microelectrodes also enable sensitive electrical impedance spectroscopy (EIS) to discern the number of immobilized cells, classify different orientations of captured cells, as well as detect potential movements of immobilized single yeast cells during the overall recording duration by using principal component analysis (PCA) in data mining. The multifrequency EIS measurements can, therefore, obtain sufficient information of S. cerevisiae cells at single-cell level.

Double-peak signal features in microfluidic impedance flow cytometry enable sensitive measurement of cell membrane capacitance

The probing of individual cells at specific frequency regimes in a microfluidic impedance flow cytometer led to the observation of unusual "double peak" features in the reactive component of the resulting signal. The phenomenon was restricted to the lower frequencies (400-800 kHz) of the β-dispersion regime and its occurrence was facilitated by the co-planar microelectrode geometry in the device. To understand the reasons for this anomalous behaviour, the system was modelled using COMSOL. The simulated model agreed well with experimental observations and provided insight into the origins of this signal profile and the effect of various parameters on its behaviour. One of the most significant observations of this study was the high sensitivity of the features in the "double peak" profile to changes in cell membrane capacitance (CMC), compared to conventional "single peaks" of reactive impedance. This was consequently exploited to accurately distinguish populations of normal and glutaraldehyde treated erythrocytes based on variations in their CMC, indicating a drastic decrease in the CMC of treated cells. Additionally, we demonstrate the applicability of using this double peak effect to identify cell populations within a mixture of PBMCs. This study is an improvement over conventional approaches of measuring CMC via impedance flow cytometry by enabling the measurement of both cell size and cell membrane properties at a single frequency rather than using multiple frequencies. Using a single frequency significantly simplifies the system and reduces the associated costs. Additionally, this technique enables the measurement of CMC at relatively low frequencies.

Electrical Impedance Spectroscopy for Monitoring Chemoresistance of Cancer Cells

Electrical impedance spectroscopy (EIS) is an electrokinetic method that allows for the characterization of intrinsic dielectric properties of cells. EIS has emerged in the last decade as a promising method for the characterization of cancerous cells, providing information on inductance, capacitance, and impedance of cells. The individual cell behavior can be quantified using its characteristic phase angle, amplitude, and frequency measurements obtained by fitting the input frequency-dependent cellular response to a resistor-capacitor circuit model. These electrical properties will provide important information about unique biomarkers related to the behavior of these cancerous cells, especially monitoring their chemoresistivity and sensitivity to chemotherapeutics. There are currently few methods to assess drug resistant cancer cells, and therefore it is difficult to identify and eliminate drug-resistant cancer cells found in static and metastatic tumors. Establishing techniques for the real-time monitoring of changes in cancer cell phenotypes is, therefore, important for understanding cancer cell dynamics and their plastic properties. EIS can be used to monitor these changes. In this review, we will cover the theory behind EIS, other impedance techniques, and how EIS can be used to monitor cell behavior and phenotype changes within cancerous cells.

Bioelectrical Analysis of Various Cancer Cell Types Immobilized in 3D Matrix and Cultured in 3D-Printed Well

Cancer cell lines are important tools for anticancer drug research and assessment. Impedance measurements can provide valuable information about cell viability in real time. This work presents the proof-of-concept development of a bioelectrical, impedance-based analysis technique applied to four adherent mammalian cancer cells lines immobilized in a three-dimensional (3D) calcium alginate hydrogel matrix, thus mimicking in vivo tissue conditions. Cells were treated with cytostatic agent5-fluoruracil (5-FU). The cell lines used in this study were SK-N-SH, HEK293, HeLa, and MCF-7. For each cell culture, three cell population densities were chosen (50,000, 100,000, and 200,000 cells/100 μL). The aim of this study was the extraction of mean impedance values at various frequencies for the assessment of the different behavior of various cancer cells when 5-FU was applied. For comparison purposes, impedance measurements were implemented on untreated immobilized cell lines. The results demonstrated not only the dependence of each cell line impedance value on the frequency, but also the relation of the impedance level to the cell population density for every individual cell line. By establishing a cell line-specific bioelectrical behavior, it is possible to obtain a unique fingerprint for each cancer cell line reaction to a selected anticancer agent.

Crossing constriction channel-based microfluidic cytometry capable of electrically phenotyping large populations of single cells

This paper presents a crossing constriction channel-based microfluidic system for high-throughput characterization of specific membrane capacitance (Csm) and cytoplasm conductivity (σcy) of single cells. In operations, cells in suspension were forced through the major constriction channel and instead of invading the side constriction channel, they effectively sealed the side constriction channel, which led to variations in impedance data. Based on an equivalent circuit model, these raw impedance data were translated into Csm and σcy. As a demonstration, the developed microfluidic system quantified Csm (3.01 ± 0.92 μF cm-2) and σcy (0.36 ± 0.08 S m-1) of 100 000 A549 cells, which could generate reliable results by properly controlling cell positions during their traveling in the crossing constriction channels. Furthermore, the developed microfluidic impedance cytometry was used to distinguish paired low- and high-metastatic carcinoma cell types of SACC-83 (ncell = ∼100 000) and SACC-LM cells (ncell = ∼100 000), distinguishing significant differences in both Csm (3.16 ± 0.90 vs. 2.79 ± 0.67 μF cm-2) and σcy (0.36 ± 0.06 vs.0.41 ± 0.08 S m-1). As high-throughput microfluidic impedance cytometry, this technique may add a new marker-free dimension to flow cytometry in single-cell analysis.

Developments in label-free microfluidic methods for single-cell analysis and sorting

Advancements in microfluidic technologies have led to the development of many new tools for both the characterization and sorting of single cells without the need for exogenous labels. Label-free microfluidics reduce the preparation time, reagents needed, and cost of conventional methods based on fluorescent or magnetic labels. Furthermore, these devices enable analysis of cell properties such as mechanical phenotype and dielectric parameters that cannot be characterized with traditional labels. Some of the most promising technologies for current and future development toward label-free, single-cell analysis and sorting include electronic sensors such as Coulter counters and electrical impedance cytometry; deformation analysis using optical traps and deformation cytometry; hydrodynamic sorting such as deterministic lateral displacement, inertial focusing, and microvortex trapping; and acoustic sorting using traveling or standing surface acoustic waves. These label-free microfluidic methods have been used to screen, sort, and analyze cells for a wide range of biomedical and clinical applications, including cell cycle monitoring, rapid complete blood counts, cancer diagnosis, metastatic progression monitoring, HIV and parasite detection, circulating tumor cell isolation, and point-of-care diagnostics. Because of the versatility of label-free methods for characterization and sorting, the low-cost nature of microfluidics, and the rapid prototyping capabilities of modern microfabrication, we expect this class of technology to continue to be an area of high research interest going forward. New developments in this field will contribute to the ongoing paradigm shift in cell analysis and sorting technologies toward label-free microfluidic devices, enabling new capabilities in biomedical research tools as well as clinical diagnostics. This article is categorized under: Diagnostic Tools > Biosensing Diagnostic Tools > Diagnostic Nanodevices.

Impedance-Based Microfluidic Assay for Automated Antischistosomal Drug Screening

Schistosomiasis is a neglected tropical disease, caused by parasitic worms, which affects almost 200 million people worldwide. For over 40 years, chemotherapeutic treatment has relied on the administration of praziquantel, an efficacious drug against schistosomiasis. However, concerns about developing drug resistance require the discovery of novel drug compounds. Currently, the drug-screening process is mostly based on the visual evaluation of drug effects on worm larvae in vitro by a trained operator. This manual process is extremely labor-intensive, has limited throughput, and may be affected by subjectivity of the operator evaluation. In this paper, we introduce a microfluidic platform with integrated electrodes for the automated detection of worm larvae viability using an impedance-based approach. The microfluidic analysis unit consists of two sets of electrodes and a channel of variable geometry to enable counting and size detection of single parasite larvae and the collective evaluation of the motility of the larvae as an unbiased estimator for their viability. The current platform also allows for multiplexing of the analysis units resulting in increased throughput. We used our platform to record size and motility variations of Schistosoma mansoni larvae exposed to different concentrations of mefloquine, a drug with established in vitro antischistosomal properties. The developed platform demonstrates the potential of integrated microfluidic platforms for high-throughput antischistosomal drug screening.

Smart Cell Culture Systems: Integration of Sensors and Actuators into Microphysiological Systems

Technological advances in microfabrication techniques in combination with organotypic cell and tissue models have enabled the realization of microphysiological systems capable of recapitulating aspects of human physiology in vitro with great fidelity. Concurrently, a number of analysis techniques has been developed to probe and characterize these model systems. However, many assays are still performed off-line, which severely compromises the possibility of obtaining real-time information from the samples under examination, and which also limits the use of these platforms in high-throughput analysis. In this review, we focus on sensing and actuation schemes that have already been established or offer great potential to provide in situ detection or manipulation of relevant cell or tissue samples in microphysiological platforms. We will first describe methods that can be integrated in a straightforward way and that offer potential multiplexing and/or parallelization of sensing and actuation functions. These methods include electrical impedance spectroscopy, electrochemical biosensors, and the use of surface acoustic waves for manipulation and analysis of cells, tissue, and multicellular organisms. In the second part, we will describe two sensor approaches based on surface-plasmon resonance and mechanical resonators that have recently provided new characterization features for biological samples, although technological limitations for use in high-throughput applications still exist.

Development of microfluidic impedance cytometry enabling the quantification of specific membrane capacitance and cytoplasm conductivity from 100,000 single cells

This paper presents a new microfluidic impedance cytometry with crossing constriction microchannels, enabling the characterization of cellular electrical markers (e.g., specific membrane capacitance (C_sm) and cytoplasm conductivity (σ_cy)) in large cell populations (~ 100,000 cells) at a rate greater than 100 cells/s. Single cells were aspirated continuously through the major constriction channel with a proper sealing of the side constriction channel. An equivalent circuit model was developed and the measured impedance values were translated to C_sm and σ_cy. Neural network was used to classify different cell populations where classification success rates were calculated. To evaluate the developed technique, different tumour cell lines, and the effects of epithelial-mesenchymal transitions on tumour cells were examined. Significant differences in both C_sm and σ_cy were found for H1299 and HeLa cell lines with a classification success rate of 90.9% in combination of the two parameters. Meanwhile, tumour cells A549 showed significant decreases in both C_sm and σ_cy after epithelial-mesenchymal transitions with a classification success rate of 76.5%. As a high-throughput microfluidic impedance cytometry, this technique can add a new marker-free dimension to flow cytometry in single-cell analysis.

Wide-band Electrical Impedance Spectroscopy (EIS) Measures S. pombe Cell Growth in vivo

This chapter describes a microfluidic device that enables immobilization and culturing of single rod-shaped S. pombe cells in a stand-up mode. The wide-band electrical impedance spectroscopy (EIS) has been integrated in the microfluidic device to continuously measure cell growth of single S. pombe cells. Cell growth curves showing cellular and intracellular features at high spatiotemporal resolution can be obtained from EIS signals. The features include longitudinal cell elongation in the G2 phase, mitosis, and cell division during an entire cell cycle of S. pombe cells. Microfluidics-based EIS systems provide, hence, a tool for dynamic single-cell studies.

Applications of Bioimpedance Measurement Techniques in Tissue Engineering

Rapid development in the field of tissue engineering necessitates implementation of monitoring methods for evaluation of the viability and characteristics of the cell cultures in a real-time, non-invasive and non-destructive manner. Current monitoring techniques are mainly histological and require labeling and involve destructive tests to characterize cell cultures. Bioimpedance measurement technique which benefits from measurement of electrical properties of the biological tissues, offers a non-invasive, label-free and real-time solution for monitoring tissue engineered constructs. This review outlines the fundamentals of bioimpedance, as well as electrical properties of the biological tissues, different types of cell culture constructs and possible electrode configuration set ups for performing bioimpedance measurements on these cell cultures. In addition, various bioimpedance measurement techniques and their applications in the field of tissue engineering are discussed.

Dynamic monitoring of single cell lysis in an impedance-based microfluidic device

A microfluidic device that is capable of trapping and sensing dynamic variations in the electrical properties of individual cells is demonstrated. The device is applied to the real-time recording of impedance measurements of mouse embryonic stem cells (mESCs) during the process of membrane lysis, with the resulting changes in the electrical properties of cells during this process being quantitatively tracked over time. It is observed that the impedance magnitude decreases dramatically after cell membrane lysis. A significant shift in the phase spectrum is also observed during the time course of this process. By fitting experimental data to physical models, the electrical parameters of cells can be extracted and parameter variations quantified during the process. In the cell lysis experiments, the equivalent conductivity of the cell membrane is found to increase significantly due to pore formation in the membrane during lysis. An increase in the specific capacitance of the membrane is also observed. On the other hand, the conductivity of the cytoplasm is observed to decrease, which may be explained the fact that excess water enters the cell through the gradual permeabilization of the membrane during lysis. Cells can be trapped in the device for periods up to several days, and their electrical response can be monitored by real-time impedance measurements in a label-free and non-invasive manner. Furthermore, due to the highly efficient single cell trapping capacity of the device, a number of cells can be trapped and held in separate wells for concurrent parallel experiments, allowing for the possibility of stepped parametric experiments and studying cell heterogeneity by combining measurements across the array.

Modeling electrical double-layer effects for microfluidic impedance spectroscopy from 100 kHz to 110 GHz

Broadband microfluidic-based impedance spectroscopy can be used to characterize complex fluids, with applications in medical diagnostics and in chemical and pharmacological manufacturing. Many relevant fluids are ionic; during impedance measurements ions migrate to the electrodes, forming an electrical double-layer. Effects from the electrical double-layer dominate over, and reduce sensitivity to, the intrinsic impedance of the fluid below a characteristic frequency. Here we use calibrated measurements of saline solution in microfluidic coplanar waveguide devices at frequencies between 100 kHz and 110 GHz to directly measure the double-layer admittance for solutions of varying ionic conductivity. We successfully model the double-layer admittance using a combination of a Cole-Cole response with a constant phase element contribution. Our analysis yields a double-layer relaxation time that decreases linearly with solution conductivity, and allows for double-layer effects to be separated from the intrinsic fluid response and quantified for a wide range of conducting fluids.

Single cell studies of mouse embryonic stem cell (mESC) differentiation by electrical impedance measurements in a microfluidic device

Biological populations of cells show considerable cell-to-cell variability. Study of single cells and analysis of cell heterogeneity are considered to be critical in understanding biological processes such as stem cell differentiation and cancer development. Recent advances in lab-on-a-chip techniques have allowed single-cell capture in microfluidic channels with the possibility of precise environmental control and high throughput of experiments with minimal usage of samples and reagents. In recent years, label-free techniques such as electrical impedance spectroscopy have emerged as a non-invasive approach to studying cell properties. In this study, we have designed and fabricated a microfluidic device that combines hydrodynamic trapping of single cells in pre-defined locations with the capability of running electrical impedance measurements within the same device. We have measured mouse embryonic stem cells (mESCs) at different states during differentiation (t=0h, 24h and 48h) and quantitatively analysed the changes in electrical parameters of cells during differentiation. A marked increase in the magnitude of the cell impedance is found during cell differentiation, which can be attributed to an increase in cell size. The analysis of the measurements shows that the nucleus-to-cytoplasm ratio decreases during this process. The degree of cell heterogeneity is observed to be the highest when the cells are at the transition state (24h), compare with cells at undifferentiated (0h) and fully differentiated (48h) states. The device enables highly efficient single cell trapping and provides sensitive, label-free electrical impedance measurements of individual cells, enabling the possibility of quantitatively analysing their physical state as well as studying the associated heterogeneity of a cell population.

Ex vivo characterization of age-associated impedance changes of single vascular endothelial cells using micro electrical impedance spectroscopy with a cell trap

We aimed to characterize aging of single vascular endothelial cells, which are indicators of senescence, using micro electrical impedance spectroscopy (μEIS) for the first time. The proposed μEIS was equipped with two barriers under the membrane actuator near the sensing electrodes, increasing its cell-trapping capability and minimizing the interference between the target cell and subsequent cells. The cell-trapping capability in μEIS with barriers was considerably improved (90%) with a capture time of 5 s or less, compared to μEIS without barriers (30%). Cells were extracted from transgenic zebrafish to minimize an initial discrepancy originating from genetic differences. In order to estimate useful parameters, cytoplasm resistance and membrane capacitance were estimated by fitting an electrical equivalent circuit to the data of ex vivo sensor output. The estimated cytoplasm resistance and membrane capacitance in the younger vascular endothelial cells were 20.16 ± 0.79 kΩ and 17.46 ± 0.76 pF, respectively, whereas those in the older cells were 17.81 ± 0.98 kΩ and 20.08 ± 1.38 pF, respectively. Discrimination of each group with different aging showed statistical significance in terms of cytoplasm resistance (p < 0.001) and membrane capacitance (p < 0.001). Considering both of the sensor and cellular level, the optimal frequency was determined as 1 MHz at which the electrical impedance of each group was clearly discriminated (p < 0.001).

Time-lapse electrical impedance spectroscopy for monitoring the cell cycle of single immobilized S. pombe cells

As a complement and alternative to optical methods, wide-band electrical impedance spectroscopy (EIS) enables multi-parameter, label-free and real-time detection of cellular and subcellular features. We report on a microfluidics-based system designed to reliably capture single rod-shaped Schizosaccharomyces pombe cells by applying suction through orifices in a channel wall. The system enables subsequent culturing of immobilized cells in an upright position, while dynamic changes in cell-cycle state and morphology were continuously monitored through EIS over a broad frequency range. Besides measuring cell growth, clear impedance signals for nuclear division have been obtained. The EIS system has been characterized with respect to sensitivity and detection limits. The spatial resolution in measuring cell length was 0.25 μm, which corresponds to approximately a 5-min interval of cell growth under standard conditions. The comprehensive impedance data sets were also used to determine the occurrence of nuclear division and cytokinesis. The obtained results have been validated through concurrent confocal imaging and plausibilized through comparison with finite-element modeling data. The possibility to monitor cellular and intracellular features of single S. pombe cells during the cell cycle at high spatiotemporal resolution renders the presented microfluidics-based EIS system a suitable tool for dynamic single-cell investigations.

Digital Microfluidics for Manipulation and Analysis of a Single Cell

The basic structural and functional unit of a living organism is a single cell. To understand the variability and to improve the biomedical requirement of a single cell, its analysis has become a key technique in biological and biomedical research. With a physical boundary of microchannels and microstructures, single cells are efficiently captured and analyzed, whereas electric forces sort and position single cells. Various microfluidic techniques have been exploited to manipulate single cells through hydrodynamic and electric forces. Digital microfluidics (DMF), the manipulation of individual droplets holding minute reagents and cells of interest by electric forces, has received more attention recently. Because of ease of fabrication, compactness and prospective automation, DMF has become a powerful approach for biological application. We review recent developments of various microfluidic chips for analysis of a single cell and for efficient genetic screening. In addition, perspectives to develop analysis of single cells based on DMF and emerging functionality with high throughput are discussed.

Maxwell's mixing equation revisited: characteristic impedance equations for ellipsoidal cells

We derived a series of, to our knowledge, new analytic expressions for the characteristic features of the impedance spectra of suspensions of homogeneous and single-shell spherical, spheroidal, and ellipsoidal objects, e.g., biological cells of the general ellipsoidal shape. In the derivation, we combined the Maxwell-Wagner mixing equation with our expression for the Clausius-Mossotti factor that had been originally derived to describe AC-electrokinetic effects such as dielectrophoresis, electrorotation, and electroorientation. The influential radius model was employed because it allows for a separation of the geometric and electric problems. For shelled objects, a special axial longitudinal element approach leads to a resistor-capacitor model, which can be used to simplify the mixing equation. Characteristic equations were derived for the plateau levels, peak heights, and characteristic frequencies of the impedance as well as the complex specific conductivities and permittivities of suspensions of axially and randomly oriented homogeneous and single-shell ellipsoidal objects. For membrane-covered spherical objects, most of the limiting cases are identical to-or improved with respect to-the known solutions given by researchers in the field. The characteristic equations were found to be quite precise (largest deviations typically <5% with respect to the full model) when tested with parameters relevant to biological cells. They can be used for the differentiation of orientation and the electric properties of cell suspensions or in the analysis of single cells in microfluidic systems.

Characterization of the distribution of rotational torque on electrorotation chips with 3D electrodes

This is a study of in-plane and out-of-plane distribution of rotational torque (ROT-T) and effective electric field (EEF) on electrorotation (ER) devices with 3D electrodes using finite element modeling (FEM) and experimental method. The objective of this study is to investigate electrical characteristics of the ER devices with five different electrode geometries and obtain an optimum structure for ER experiments. Further, it provides a comparison between characteristics of the 3D electrodes and traditionally used 2D electrodes. 3D distributions of EEF were studied by the time-variant FEM. FEM results were verified experimentally by studying the rotation of biological cells. The results show that the variations of ROT-T and EEF over the measurement area of the devices are considerably large. This can potentially lead to misinterpretation of recorded data. Therefore, it is essential to specify the boundaries of the measurement area with minimum deviation from the central EEF. For this purpose, FE analyses were utilized to specify the optimal region. Thereby, with confining the measurements to these regions, the dependency of ROT-T on the spatial position of the particles can be eliminated. Comparisons have been made on the sustainability of the EEF and ROT-T distributions for each device, to find an optimum design. Analyses of the devices prove that utilization of the 3D electrodes eliminate irregularities of EEF and ROT-T along the z-axis. The Results show that triangular electrodes provide the highest sustainability for the in-plane ROT-T and EEF distribution, while the oblate elliptical and circular electrodes have the lowest variances along the z-axis.

Single Cell Electrical Characterization Techniques

Electrical properties of living cells have been proven to play significant roles in understanding of various biological activities including disease progression both at the cellular and molecular levels. Since two decades ago, many researchers have developed tools to analyze the cell’s electrical states especially in single cell analysis (SCA). In depth analysis and more fully described activities of cell differentiation and cancer can only be accomplished with single cell analysis. This growing interest was supported by the emergence of various microfluidic techniques to fulfill high precisions screening, reduced equipment cost and low analysis time for characterization of the single cell’s electrical properties, as compared to classical bulky technique. This paper presents a historical review of single cell electrical properties analysis development from classical techniques to recent advances in microfluidic techniques. Technical details of the different microfluidic techniques are highlighted, and the advantages and limitations of various microfluidic devices are discussed.

Microfluidic impedance flow cytometry enabling high-throughput single-cell electrical property characterization

This article reviews recent developments in microfluidic impedance flow cytometry for high-throughput electrical property characterization of single cells. Four major perspectives of microfluidic impedance flow cytometry for single-cell characterization are included in this review: (1) early developments of microfluidic impedance flow cytometry for single-cell electrical property characterization; (2) microfluidic impedance flow cytometry with enhanced sensitivity; (3) microfluidic impedance and optical flow cytometry for single-cell analysis and (4) integrated point of care system based on microfluidic impedance flow cytometry. We examine the advantages and limitations of each technique and discuss future research opportunities from the perspectives of both technical innovation and clinical applications.

Microfluidic single sperm entrapment and analysis

Selection of healthy spermatozoa is of crucial importance for the success rates of assisted reproduction technologies (ART) such as in vitro fertilization and intra-cytoplasmic sperm injection. Although sperm selection for ART procedures is predominantly based on sperm motility, successful fertilization is not predicted by good motility alone. For example, sperm characteristics such as the acrosome state and DNA integrity have shown significant impact on ART outcome. Although fertilization can be achieved with a single spermatozoon of high quality, current quality assessments are population-based and do not allow investigation of multiple sperm characteristics on a single spermatozoon simultaneously. In order to study sperm cells on the single cell level, we designed and characterized a PDMS microfluidic platform that allows single sperm entrapment. After spatially confining individual sperm cells within microfluidic cell traps, the cell viability, chromosomal content and acrosome state were studied. This platform is suitable for the analysis of individual sperm cells, which could be exploited for (non-invasive) sperm analysis and selection by impedance or Raman spectroscopy.

Monitoring cellular stress responses using integrated high-frequency impedance spectroscopy and time-resolved ELISA

We have developed a lab-on-a-chip system for continuous and non-invasive monitoring of microfluidic cell cultures using integrated high-frequency contactless impedance spectroscopy. Electrically insulated microfabricated interdigitated electrode structures were embedded into four individually addressable microchambers to reliably and reproducibly detect cell-substrate interactions, cell viability and metabolic activity. While silicon nitride passivated sensor substrates provided a homogeneous cell culture surface that minimized cell orientation along interdigitated electrode structures, the application of high-frequency AC fields reduced the impact of the 300 nm thick passivation layer on sensor sensitivity. The additional implementation of multivariate data analysis methods such as partial least square (PLS) for high-frequency impedance spectra provided unambiguous information on intracellular pathway activation, up and down-regulation of protein synthesis as well as global cellular stress responses. A comparative cell analysis using connective tissue fibroblasts showed that high-frequency contactless impedance spectroscopy and time-resolved quantification of IL-6 secretion using ELISA provided similar results following stimulation with circulating pro-inflammatory cytokines IL-1β and TNFα. The combination of microfluidics with contactless impedance sensing and time-resolved quantification of stress factor release will provide biologist with a new tool to (a) establish a variety of uniform cell culture surfaces that feature complex biochemistries, micro- and nanopatterns; and (b) to simultaneously characterize cell responses under physiologically relevant conditions using a complementary non-invasive cell analysis method.

Real-time monitoring of immobilized single yeast cells through multifrequency electrical impedance spectroscopy

We present a microfluidic device, which enables single cells to be reliably trapped and cultivated while simultaneously being monitored by means of multifrequency electrical impedance spectroscopy (EIS) in the frequency range of 10 kHz-10 MHz. Polystyrene beads were employed to characterize the EIS performance inside the microfluidic device. The results demonstrate that EIS yields a low coefficient of variation in measuring the diameters of captured beads (~0.13%). Budding yeast, Saccharomyces cerevisiae, was afterwards used as model organism. Single yeast cells were immobilized and measured by means of EIS. The bud growth was monitored through EIS at a temporal resolution of 1 min. The size increment of the bud, which is difficult to determine optically within a short time period, can be clearly detected through EIS signals. The impedance measurements also reflect the changes in position or motion of single yeast cells in the trap. By analyzing the multifrequency EIS data, cell motion could be qualitatively discerned from bud growth. The results demonstrate that single-cell EIS can be used to monitor cell growth, while also detecting potential cell motion in real-time and label-free approach, and that EIS constitutes a sensitive tool for dynamic single-cell analysis.

Battery-powered portable instrument system for single-cell trapping, impedance measurements, and modeling analyses

A battery-powered portable instrument system for the single-HeLa-cell trapping and analyses is developed. A method of alternating current electrothermal (ACET) and DEP are employed for the cell trapping and the method of impedance spectroscopy is employed for cell characterizations. The proposed instrument (160 mm × 170 mm × 110 mm, 1269 g) equips with a highly efficient energy-saving design that promises approximately 120 h of use. It includes an impedance analyzer performing an excitation voltage of 0.2-2 Vpp and a frequency sweep of 11-101 kHz, function generator with the sine wave output at an operating voltage of 1-50 Vpp with a frequency of 4-12 MHz, cell-trapping biochip, microscope, and input/output interface. The biochip for the single cell trapping is designed and simulated based on a combination of ACET and DEP forces. In order to improve measurement accuracy, the curve fitting method is adopted to calibrate the proposed impedance spectroscopy. Measurement results from the proposed system are compared with results from a precision impedance analyzer. The trapped cell can be modeled for numerical analyses. Many advantages are offered in the proposed instrument such as the small volume, real-time monitoring, rapid analysis, low cost, low-power consumption, and portable application.

Label-free cell-based assay with spectral-domain optical coherence phase microscopy

Quantitative measurement of dynamic responses of unstained living cells is of great importance in many applications ranging from investigation of fundamental cellular functions to drug discoveries. Conventional optical methods for label-free cell-based assay examine cellular structural changes proximal to sensor surfaces under external stimuli, but require dedicated nanostructure-patterned substrates for operation. Here, we present a quantitative imaging method, spectral-domain optical coherence phase microscopy (SD-OCPM), as a viable optical platform for label-free cell-based assay. The instrument is based on a low-coherence interferometric microscope that enables quantitative depth-resolved phase measurement of a transparent specimen with high phase stability. We demonstrate SD-OCPM measurement of dynamic responses of human breast cancer cells (MCF-7) to 2-picolinic acid (PA) and histamine.

Assessment of effects of multi drug resistance on dielectric properties of K562 leukemic cells using electrorotation

In this study, dielectric characterization of multidrug resistant (MDR) K562 human leukemia cells was carried out using a MEMS based electrorotation (ER) device with 3D electrodes.

Evaluation of single cell electrical parameters from bioimpedance of a cell suspension

The present study introduces a simple and detailed analysis technique to extract the electrical properties of a single cell from impedance spectroscopy data from a group of cells in suspension, leading to a more reliable and cost effective diagnosis process for disease detection.

Microfluidic chip with integrated electrical cell-impedance sensing for monitoring single cancer cell migration in three-dimensional matrixes

Cell migration has been recognized as one hallmark of malignant tumor progression. By integrating the method of electrical cell-substrate impedance sensing (ECIS) with the Boyden chamber design, the state-of-the-art techniques provide kinetic information about cell migration and invasion processes in three-dimensional (3D) extracellular matrixes. However, the information related to the initial stage of cell migration with single-cell resolution, which plays a unique role in the metastasis-invasion cascade of cancer, is not yet available. In this paper, we present a microfluidic device integrated with ECIS for investigating single cancer cell migration in 3D matrixes. Using microfluidics techniques without the requirement of physical connections to off-chip pneumatics, the proposed sensor chip can efficiently capture single cells on microelectrode arrays for sequential on-chip 2D or 3D cell culture and impedance measurement. An on-chip single-cell migration assay was successfully demonstrated within several minutes. Migration of single metastatic MDA-MB-231 cells in their initial stage can be monitored in real time; it shows a rapid change in impedance magnitude of approximately 10 Ω/s, whereas no prominent impedance change is observed for less-metastasis MCF-7 cells. The proposed sensor chip, allowing for a rapid and selective detection of the migratory properties of cancer cells at the single-cell level, could be applied as a new tool for cancer research.

Electric impedance microflow cytometry for characterization of cell disease states

The electrical properties of biological cells have connections to their pathological states. Here we present an electric impedance microflow cytometry (EIMC) platform for the characterization of disease states of single cells. This platform entails a microfluidic device for a label-free and non-invasive cell-counting assay through electric impedance sensing. We identified a dimensionless offset parameter δ obtained as a linear combination of a normalized phase shift and a normalized magnitude shift in electric impedance to differentiate cells on the basis of their pathological states. This paper discusses a representative case study on red blood cells (RBCs) invaded by the malaria parasite Plasmodium falciparum. Invasion by P. falciparum induces physical and biochemical changes on the host cells throughout a 48-h multi-stage life cycle within the RBC. As a consequence, it also induces progressive changes in electrical properties of the host cells. We demonstrate that the EIMC system in combination with data analysis involving the new offset parameter allows differentiation of P. falciparum infected RBCs from uninfected RBCs as well as among different P. falciparum intraerythrocytic asexual stages including the ring stage. The representative results provided here also point to the potential of the proposed experimental and analysis platform as a valuable tool for non-invasive diagnostics of a wide variety of disease states and for cell separation.

Recent advances in microfluidic techniques for single-cell biophysical characterization

Biophysical (mechanical and electrical) properties of living cells have been proven to play important roles in the regulation of various biological activities at the molecular and cellular level, and can serve as promising label-free markers of cells' physiological states. In the past two decades, a number of research tools have been developed for understanding the association between the biophysical property changes of biological cells and human diseases; however, technical challenges of realizing high-throughput, robust and easy-to-perform measurements on single-cell biophysical properties have yet to be solved. In this paper, we review emerging tools enabled by microfluidic technologies for single-cell biophysical characterization. Different techniques are compared. The technical details, advantages, and limitations of various microfluidic devices are discussed.

A microfluidic system for cell type classification based on cellular size-independent electrical properties

This paper presents a microfluidic system enabling cell type classification based on continuous characterization of size-independent electrical properties (e.g., specific membrane capacitance (C(specific membrane)) and cytoplasm conductivity (σ(cytoplasm)). In this study, cells were aspirated continuously through a constriction channel, while cell elongation and impedance profiles at two frequencies (1 kHz and 100 kHz) were measured simultaneously. Based on a proposed distributed equivalent circuit model, 1 kHz impedance data were used to evaluate cellular sealing properties with constriction channel walls and 100 kHz impedance data were translated to C(specific membrane) and σ(cytoplasm). Two lung cancer cell lines of CRL-5803 cells (n(cell) = 489) and CCL-185 cells (n(cell) = 487) were used to evaluate this technique, producing a C(specific membrane) of 1.63 ± 0.52 μF cm(-2) vs. 2.00 ± 0.60 μF cm(-2), and σ(cytoplasm) of 0.90 ± 0.19 S m(-1)vs. 0.73 ± 0.17 S m(-1). Neural network-based pattern recognition was used to classify CRL-5803 and CCL-185 cells, producing success rates of 65.4% (C(specific membrane)), 71.4% (σ(cytoplasm)), and 74.4% (C(specific membrane) and σ(cytoplasm)), suggesting that these two tumor cell lines can be classified based on their electrical properties.

Dielectric spectroscopy as a viable biosensing tool for cell and tissue characterization and analysis

The use of dielectric spectroscopy to carry out real time observations of cells and to extract a wealth of information about their physiological properties has expanded in recent years. This popularity is due to the simple, easy to use, non-invasive and real time nature of dielectric spectroscopy. The ease of integrating dielectric spectroscopy with microfluidic devices has allowed the technology to further expand into biomedical research. Dielectric spectra are obtained by applying an electrical signal to cells, which is swept over a frequency range. This review covers the different methods of interpreting dielectric spectra and progress made in applications of impedance spectroscopy for cell observations. First, methods of obtaining specific electrical properties of cells (cell membrane capacitance and cytoplasm conductivity) are discussed. These electrical properties are obtained by fitting the dielectric spectra to different models and equations. Integrating models to reduce the effects of the electrical double layer are subsequently covered. Impedance platforms are then discussed including electrical cell substrate impedance sensing (ECIS). Categories of ECIS systems are divided into microelectrode arrays, interdigitated electrodes and those that allow differential ECIS measurements. Platforms that allow single cell and sub-single cell measurements are then discussed. Finally, applications of impedance spectroscopy in a range of cell observations are elaborated. These applications include observing cell differentiation, mitosis and the cell cycle and cytotoxicity/cell death. Future applications such as drug screening and in point of care applications are then covered.

Microfluidic device for trapping and monitoring three dimensional multicell spheroids using electrical impedance spectroscopy

In this paper, we report the design, fabrication, and testing of a lab-on-a-chip based microfluidic device for application of trapping and measuring the dielectric properties of microtumors over time using electrical impedance spectroscopy (EIS). Microelectromechanical system (MEMS) techniques were used to embed opposing electrodes onto the top and bottom surfaces of a microfluidic channel fabricated using Pyrex substrate, chrome gold, SU-8, and polydimethylsiloxane. Differing concentrations of cell culture medium, differing sized polystyrene beads, and MCF-7 microtumor spheroids were used to validate the designs ability to detect background conductivity changes and dielectric particle diameter changes between electrodes. The observed changes in cell medium concentrations demonstrated a linear relation to extracted solution resistance (Rs), while polystyrene beads and multicell spheroids induced changes in magnitude consistent with diameter increase. This design permits optical correlation between electrical measurements and EIS spectra.

Microcapillary-assisted dielectrophoresis for single-particle positioning

Here, we demonstrate microcapillary-assisted dielectrophoresis (μC-DEP), a new capability for precise positioning of particles or biological cells in applications such as dynamic assays. The method largely derives from a need to evade the challenges faced with hydrodynamic trapping of particles or cells at microcapillaries typically realized through brief application of suction. Microcapillaries here serve a dual purpose by firstly squeezing field lines to define localized positive DEP traps and then establishing an exclusive access to the trapped cell for probing. Strength of the traps is presented through numerical results at various excitation frequencies. Their effectiveness is shown experimentally against relevant solution conductivities using 10 μm polystyrene microspheres. Usefulness of the method for positioning individual cells is demonstrated via experimental results on cell viability and single-cell impedance spectroscopy.

Quantification of the specific membrane capacitance of single cells using a microfluidic device and impedance spectroscopy measurement

The specific membrane capacitance (SMC) is an electrical parameter that correlates with both the electrical activity and morphology of the plasma membrane, which are physiological markers for cellular phenotype and health. We have developed a microfluidic device that enables impedance spectroscopy measurements of the SMC of single biological cells. Impedance spectra induced by single cells aspirated into the device are captured over a moderate frequency range (5 kHz-1 MHz). Maximum impedance sensitivity is achieved using a tapered microfluidic channel, which effectively routes electric fields across the cell membranes. The SMC is extracted by curve-fitting impedance spectra to an equivalent circuit model. From our measurement, acute myeloid leukemia (AML) cells are found to exhibit larger SMC values in hypertonic solutions as compared with those in isotonic solutions. In addition, AML cell phenotypes (AML2 and NB4) exhibiting varying metastatic potential yield distinct SMC values (AML2: 16.9 ± 1.9 mF/m(2) (n = 23); NB4: 22.5 ± 4.7 mF/m(2) (n = 23)). Three-dimensional finite element simulations of the microfluidic device confirm the feasibility of this approach.

Microfluidics-based assessment of cell deformability

Mechanical properties of cells have been shown to have a significant role in disease, as in many instances cell stiffness changes when a cell is no longer healthy. We present a high-throughput microfluidics-based approach that exploits the connection between travel time of a cell through a narrow passage and cell stiffness. The system resolves both cell travel time and relative cell diameter while retaining information on the cell level. We show that stiffer cells have longer transit times than less stiff ones and that cell size significantly influences travel times. Experiments with untreated HeLa cells and cells made compliant with latrunculin A and cytochalasin B further demonstrate that travel time is influenced by cell stiffness, with the compliant cells having faster transit time.