Environmental rethinking of wastewater drains to manage environmental pollution and alleviate water scarcity

Assessment of the spatiotemporal evolution of the groundwater quality using the WQI and trend analysis in the Eastern Mitidja plain (North of Algeria)

The imbalance between groundwater recharge and exploitation has led to water scarcity. The Eastern Mitidja aquifer is facing the problem of groundwater depletion and deteriorating quality. This work aims to study the spatiotemporal evolution of the groundwater quality, based on statistical trend tests and the water quality index (WQI). The statistical analysis reveals that the WQI varies from 44.404 to 496.7 and from 28.24 to 398.666 for the wet and dry seasons, respectively. The results allow groundwater to be classified as "good" to "very poor" water quality. The prediction maps show that the highest WQI values (for both seasons) are located in the extreme east of the plain, while it deteriorates in the other regions over the years (2005-2020), especially during wet season. The WQI's temporal evolution was examined by two statistical trend tests, namely, the Seasonal Mann-Kendall (SMK) test and the Şen's Innovative Trend Analysis (ITA) method. The results revealed a significant upward trend in more than 50% of the sampled points for both seasons. For comparison purposes, the Seasonal Mann-Kendall test and the Şen's Innovative Trend Analysis method was applied to the same data. As a result, the ITA method could be successfully used for trend analysis of water quality parameters. Groundwater quality in the Mitidja East appears to be poor in general, and will deteriorate more given the upward trend in WQI revealed by the previous methods. Owing to the importance of this resource for agriculture, industry and human consumption, protecting it against various types of contamination and continuous monitoring will be essential.

Algal-bacterial bioremediation of cyanide-containing wastewater in a continuous stirred photobioreactor

This study reports the isolation and characterization of highly resistant bacterial and microalgal strains from an Egyptian wastewater treatment station to cyanide-containing compounds. The bacterial strain was identified as Bacillus licheniformis by 16S rRNA gene sequencing. The isolate removed up to 1 g L-1 potassium cyanide, 3 g L-1 benzonitrile, and 1 g L-1 sodium salicylate when incubated as 10% v/v in MSM at 30 ℃. However, it failed to degrade potassium thiocyanate at all tested concentrations. The microalgal isolate was identified by electron microscopy as a strain of Chlorella spp.. Algal toxicity was tested by incubating the microalgae as 6% v/v in MSM containing 2 g L- 1 NaHCO3 with increasing concentrations of the pollutants. Results showed that 0.05 g L-1 KCN, 1.5 g L-1 benzonitrile, 5 g L -1 KSCN, and 5 g L-1 sodium salicylate inhibited 93%, 96%, 75%, and 21% of algal growth, respectively. In a continuous stirred photobioreactor, the bacterial-microalgal microcosm detoxified synthetic wastewater containing 0.2 g L-1 KCN, 0.1 g L-1 benzonitrile, and 0.5 g L-1 sodium salicylate in 3.5 days of hydraulic retention time. System failure was recorded when the KCN concentration was increased to 0.25 g L-1. The effluent had no inhibitory effect on the germination of Lepidium sativum seeds in phytotoxicity testing. Temperature, pH, and chitosan effects were assessed on the algal/bacterial settleability. Statistical analysis showed no significant difference between the tested parameters. The microcosm represents a potential candidate for the treatment of industrial wastewater containing cyanide compounds.

Evaluating the role of recalcitrant dissolved organic matter in bacterial community dynamics in urbanized freshwater ecosystems

Dissolved organic matter (DOM) and recalcitrant dissolved organic matter (RDOM) play distinct roles in shaping microbial communities. However, characterizing these roles is difficult, especially in ecosystems subjected to varying degrees of anthropogenic influence. This study investigated the molecular compositions and ecological impacts of DOM and RDOM in the Fen River, Shanxi Taiyuan, comparing pristine upstream regions with highly urbanized downstream areas. Using 16S rRNA gene sequencing and LC-MS-based metabolomics, we observed significant shifts in microbial community composition, diversity, and metabolic functions. Upstream communities, characterized by higher diversity, were dominated by Bacteroidota, Proteobacteria, and Cyanobacteria, while downstream communities, influenced by pollution, exhibited increased expression of genes related to amino acid metabolism. Fluorescence spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) revealed that upstream DOM contained higher proportions of complex, high molecular weight compounds, including significant proportions of carboxyl-rich alicyclic molecules (CRAM) and island of stability (IOS) compounds, which play key roles in long-term carbon storage and microbial carbon sequestration. In contrast, downstream DOM was characterized as having lower aromaticity and more saturated compounds, with reduced proportions of CRAM and IOS, reflecting the impact of anthropogenic activities. These findings underscored the critical roles of CRAM and IOS in regulating DOM stability and microbial communities, further highlighting the need for targeted pollution control strategies to preserve ecosystem function in urbanized water bodies.

Modelling the impacts generated by reclaimed wastewater reuse in agriculture: From literature gaps to an integrated risk assessment in a One Health perspective

The reuse of reclaimed wastewater is increasingly recognized as a viable alternative water source for irrigation. Its application, whether direct or indirect, impacts several interconnected compartments, including groundwater, surface water, soil, crops, and humans. Reclaimed wastewater provides essential resources for crops, like water and nutrients. However, it also introduces pathogens, and contaminants of emerging concern (CECs), defined as chemicals that may pose risks to human health and ecosystems but are not yet fully regulated, such as pharmaceuticals and personal care products, among others. Additionally, reclaimed wastewater may contain antibiotic-resistant bacteria (ARBs) and disinfection by-products (DBPs), all of which present potential health and environmental risks. Therefore, regulatory bodies stress the need for preventive risk assessments to ensure safe reuse. This paper critically reviews available models for assessing the impacts of reclaimed wastewater reuse in agriculture. It identifies gaps in current modelling approaches and outlines future research directions. Key areas requiring further investigation include the fate and transfer of CECs, ARBs and DBPs, and the co-occurrence of multiple risks in such interconnected systems, especially in the indirect reuse. To address these gaps, we proposed a simplified approach to integrate three types of risk associated with CECs in indirect reuse, focusing on risks posed by antibiotics and other pharmaceuticals: human health risk, environmental risk and risk from antibiotic resistance development. This approach aids in identifying the most critical endpoints within the One Health approach, supporting (i) CECs prioritization in regulations based on their critical endpoints and (ii) the adoption of CEC-specific mitigation measures.

Effect of super absorbent hydrogel on hydro-physical properties of soil under deficit irrigation

Due to water scarcity challenges, efficient management of irrigation water is becoming crucial. Water use efficiency (WUE) involves increasing crop productivity without increasing water consumption. This study was carried out to study the effect of hydrogel, deficit irrigation and soil type on WUE, soil hydro-physical properties and lettuce productivity. For this purpose, four irrigation treatments (100%, 85%, 70% and 60% of full irrigation requirements), four hydrogel concentrations (0, 0.1, 0.2 and 0.3% w/w) and three soil textural classes (clay, loamy sand, and sandy-clay soil) were conducted in pot experiment at open field during two consecutive seasons. The results revealed that crop growth parameters and soil hydro-physical properties were significantly affected by hydrogel application rates. Hydrogel addition significantly enhanced head fresh and dry weights, chlorophyll content, number of leaves and WUE. Application of hydrogel at 0.3% and 85% of irrigation requirements achieved the highest WUE without significant yield reductions. Changes in the studied hydro-physical properties of soil were more dependent on soil texture and hydrogel application rate than on the amount of irrigation water. The significant decrease in soil saturated hydraulic conductivity and bulk density confirms that super absorbent hydrogels could be recommended to improve soil water retention and enhance water use efficiency under deficit irrigation conditions.

Integrating microalgae-based wastewater treatment, biostimulant production, and hydroponic cultivation: a sustainable approach to water management and crop production

A natural appearing microalgae-bacteria consortium was used to process urban wastewater. The process was done in an 80 m2 raceway reactor and the results were compared to an identical reactor operated using freshwater supplemented with commercial fertilisers. The biomass harvesting was done using commercial ultrafiltration membranes to reduce the volume of culture centrifuged. The membrane allowed achieving a biomass concentration of ∼9-10 g L-1. The process proposed avoids the use of centrifuges and the drying of the biomass, two of the most energy consuming steps of conventional processes. The specific growth rate in freshwater and the wastewater-based media was estimated as 0.30 ± 0.05 and 0.24 ± 0.02 days-1, respectively (p < 0.05). The maximum concentration reached at the end of the batch phase was 0.96 ± 0.03 and 0.83 ± 0.07 g L-1 when the biomass was produced using freshwater and wastewater, respectively (p < 0.05). The total nitrogen removal capacity of the system was on average 1.35 g m-2·day-1; nitrogen assimilation into biomass represented 60%-95% of this value. Furthermore, the P-PO4 3- removal capacity of the system varied from 0.15 to 0.68 g m-2·day-1. The outlet effluent of the reactor was used as a nutrient source in the hydroponic production of zucchini seedlings, leading to an increase in the root dry weight and the stem diameter compared to the water alone. The produced biomass showed potential for use as feedstock to produce plant biostimulants with positive effects on root development and chlorophyll retention.

Numerical simulation of different pollutant control measures around an old landfill contaminated site: A field scale study

The remediation of contaminated soils is a great challenge for global environmental sciences and engineering. The landfill was a kind of infrastructure to deal with waste from different sources while it would also cause the threat to groundwater. Cut-off walls and pumping wells were usually applied in the landfill to prevent the spread of pollutants to wider areas. However, the combination of using both of methods was rarely analyzed, especially using field data for calibrating and fitting groundwater flow and pollutant transport. 7 monitoring wells were arranged in the study area to survey the subsurface seepage. The pollution monitoring was carried out for a period of 50 days, covering 31 types of inorganic and organic pollutants. The concentration of 2,4,6-trichlorophenol (TCP) was 556.7 times greater than the standard concentration. A coupled numerical model of groundwater flow and pollutant transport was developed to assess the effectiveness of various control methods. Three options were tested, including the implementation of a single cut-off wall as well as a combination of a cut-off wall and a pumping well, for preventing the discharge of pollutants from landfills. The combination of a cut-off wall and a pumping well is the best strategy for removal of TCP. The combination approaches lead to a reduction of pollution plumes by a factor of 11 compared to the case without pollution control measures. The research findings may provide a basis and reference for the application of cutoff walls and pumping well in landfill sites or contaminated groundwater.

Spatially Explicit Wastewater Generation and Tracking (SEWAGE-TRACK) in the Middle East and North Africa region

This study developed the SEWAGE-TRACK model for disaggregating lumped national wastewater generation estimates using population datasets and quantifying rural and urban wastewater generation and fate. The model allocates wastewater into riparian, coastal, and inland components and summarizes the fate of wastewater into productive (direct and indirect reuse) and unproductive components for 19 countries in the Middle East and North Africa (MENA) region. As per the national estimates, 18.4 km³ of municipal wastewater generated in 2015, was disaggregated over the MENA region. Results from this study revealed urban and rural areas to contribute to 79 % and 21 % of municipal wastewater generation respectively. Within the rural context, inland areas generated 61 % of the total wastewater. The riparian and coastal regions produced 27 % and 12 %, respectively. Within the urban settings, riparian areas produced 48 %, while inland and coastal regions generated 34 % and 18 % of the total wastewater, respectively. Results indicate that 46 % of the wastewater is productively used (direct reuse and indirect use), while 54 % is lost unproductively. Of the total wastewater generated, the most direct use was observed in the coastal areas (7 %), the most indirect reuse in the riparian regions (31 %), and the most unproductive losses in inland areas (27 %). The potential of unproductive wastewater as a non-conventional freshwater source was also analyzed. Our results indicate that wastewater is an excellent alternative water source and has high potential to reduce pressure on non-renewable sources for some countries in the MENA region. The motivation of this study is to disaggregate wastewater generation and track wastewater fate using a simple but robust approach that is portable, scalable and repeatable. Similar analysis can be done for other regions to produce information on disaggregated wastewater and its fate. Such information is highly critical for efficient wastewater resource management.

Additive-optimized micro-structure in cellulose acetate butyrate-based reverse osmosis membrane for desalination

Progress toward the high water flux of cellulose acetate butyrate (CAB)-based reverse osmosis (RO) membrane is a bottleneck for desalination and mitigation of fresh water shortage. Here, we develop an "optimization of formulation-induced structure" strategy using acetone (solvent), triethyl phosphate (pore-inducing agent), glycerin and n-propanol (boosters), which achieves a state-of-the-art salt rejection of 97.1% and permeate flux of 8.73 L m^-2·h^-1, ranking top among CAB-based RO membrane. Compared with reported literatures, it represents high separation performance for different concentrations (20-100 mg L^-1) of Rhodamine B and Congo red, different ion types (NaCl and MgCl₂), different time (600 min), and resistance to feed pressure changes. The key is the appropriate viscosity of the casting solution (995.52 mPa s), the synergy between the components and additives, contributing to the formation of "jellyfish"-like microscopic pore structure with the lowest surface roughness (Ra = 16.3) and good hydrophilicity. The proposed correlation mechanism between additive-optimized micro-structure and desalination provides a promising prospect for CAB-based RO membrane.

Estimation of sulfur fate and contribution to VSC emissions from lakes during algae decay

Algae decay is an important process influencing environmental variables and emissions of volatile sulfur compounds (VSCs) in eutrophic lakes. However, effects of algae decay on VSC emissions from eutrophic lakes as well as fate of algae-derived sulfur remain poorly understood. In this study, simulated algae-sediment systems were used to explore the flow and distribution of sulfur during algae decay. VSCs including hydrogen sulfide (H₂S), methanethiol (CH₃SH), carbon disulfide (CS₂) and dimethyl sulfide ((CH₃)₂S) were detected during algae decay, which increased with algae biomass and eutrophic levels in lakes. During algae decay, the highest H₂S, CH₃SH and (CH₃)₂S emission rates of 10.45, 21.82 and 43.26 μg d^-1 occurred in the first 1-2 days, respectively, while the highest CS₂ emission rates were observed between days 8 and 11. The maximum emissions of H₂S and CS₂ from algae decay were estimated at 0.51 and 0.35 mg m^-2 d^-1 in Lake Taihu, accounting for 1.57% and 0.69% of the total H₂S and CS₂ emissions of in situ, respectively. Algae decay could significantly increase the contents of total sulfur and total carbon in sediments by 2.90%-21.11% and 4.23%-45.05%, respectively. The VSC emissions during algae decay could be predicted using the multiple regression models with the contents of total carbon, total nitrogen and sulfur-containing compounds in sediments. Partial least squares path modelling demonstrated that algae decay had a low direct effect on VSC emissions with a strength of 0.06, while it had a significant influence on environmental variables with a strength of 0.63, which could affect VSC emissions with a strength of 0.85, indicating VSC emissions from eutrophic lakes were affected by the environmental variables rather than the direct influence of algae decay. These findings illustrated the mechanisms of VSC emissions during algae decay and provided insights into VSC control and mitigation for eutrophic lakes.

Detection and Degradation Studies of Nile Blue Sulphate Using Electrochemical and UV-Vis Spectroscopic Techniques

An efficient and reliable electrochemical sensing platform based on COOH-fMWCNTs modified GCE (COOH-fMWCNTs/GCE) was designed for the detection of nanomolar concentration of Nile Blue Sulphate (NBS). In comparison to the bare GCE, the electrochemical sensing scaffold considerably enhanced the peak current response of NBS dye as confirmed from the results of voltammetric investigations. The electrochemical approach of detecting NBS in the droplet of its solution dried over the surface of modified electrode validated, the role of modifier in enhancing the sensing response. Under optimized conditions, the designed electrochemical platform demonstrated a wide linearity range (0.03–10 μM) for NBS, with LOD of 1.21 nM. Moreover, COOH-fMWCNTs/GCE was found reproducible and stable as confirmed by repeatability and inter-day durability tests. The selectivity of the designed sensing matrix was ensured by anti-interference tests. The photocatalytic degradation of NBS dye was carried out by using TiO2 nanoparticles as photocatalyst in the presence of H2O2. UV-visible spectroscopic studies revealed 95% photocatalytic degradation of NBS following a pseudo-first-order kinetics with a rate constant of 0.028 min−1. These findings were supported electrochemically by monitoring the photocatalytically degraded dye at the designed sensing platform. The color variation and final decolorization of the selected dye in water served as a visual indicator of the degradation process. To conclude, the designed sensing platform immobilized with COOH-fMWCNTs imparted improved selectivity and sensitivity to detect and to, monitor the photocatalytic degradation of NBS.

Potential use of algae for the bioremediation of different types of wastewater and contaminants: Production of bioproducts and biofuel for green circular economy

Remediation by algae is a very effective strategy for avoiding the use of costly, environmentally harmful chemicals in wastewater treatment. Recently, industries based on biomass, especially the bioenergy sector, are getting increasing attention due to their environmental acceptability. However, their practical application is still limited due to the growing cost of raw materials such as algal biomass, harvesting and processing limitations. Potential use of algal biomass includes nutrients recovery, heavy metals removal, COD, BOD, coliforms, and other disease-causing pathogens reduction and production of bioenergy and valuable products. However, the production of algal biomass using the variable composition of different wastewater streams as a source of growing medium and the application of treated water for subsequent use in agriculture for irrigation has remained a challenging task. The present review highlights and discusses the potential role of algae in removing beneficial nutrients from different wastewater streams with complex chemical compositions as a biorefinery concept and subsequent use of produced algal biomass for bioenergy and bioactive compounds. Moreover, challenges in producing algal biomass using various wastewater streams and ways to alleviate the stress caused by the toxic and high concentrations of nutrients in the wastewater stream have been discussed in detail. The technology will be economically feasible and publicly accepted by reducing the cost of algal biomass production and reducing the loaded or attached concentration of micropollutants and pathogenic microorganisms. Algal strain improvement, consortium development, biofilm formation, building an advanced cultivation reactor system, biorefinery concept development, and life-cycle assessment are all possible options for attaining a sustainable solution for sustainable biofuel production. Furthermore, producing valuable compounds, including pharmaceutical, nutraceutical and pigment contents generated from algal biomass during biofuel production, could also help reduce the cost of wastewater management by microalgae.

Improved feed forward with bald eagle search for conjunctive water management in deficit region

Due to increasing requirements on water resources and a lower recharge rate, the farming seasons are a vital season for the management of groundwater and surface water resource management. This condition necessitates the use of combined water distribution to meet the full water requirements. Analysis of existing surface water resources and related restrictions, this research suggested an algorithm for aquifer stabilization and fulfilling optimum water requirements. To manage the optimum withdrawals and the subsequent drop, this technique first employed the MODFLOW model for simulating the water levels. Next, an improved feed-forward neural network (IFFNN) was combined with an optimization method to create a machine learning (ML) framework. During the last phase, the findings of the optimized connectives approach as well as the relevant fields technologies to determine using improved bald eagle search with least square SVM(IBES-LSSVM) method that predicted the level of water deficit for every period, especially during farming seasons. This approach is based on an improved bald eagle search (IBES) optimization technique for finding the best settings for a least-squares support vector machine (LSSVM). The findings revealed that between 2005 and 2020, the year with the biggest water deficit was 2018 when only roughly 64 percent of water need was satisfied by groundwater (69 percent) and surface water (64 percent) (33 percent). The water depth may have risen by around 0.7 m during the study period if the optimum model had been used. The outcome of this research will help the management forecast future water shortages and make smarter water strategic choices.

Groundwater Quality Modeling and Mitigation from Wastewater Used in Irrigation, a Case Study of the Nile Delta Aquifer in Egypt

Groundwater is an essential freshwater source because traditional sources of freshwater, such as rainfall and rivers, are unable to provide all residential, industrial, and agricultural demands. Groundwater is replenished by different sources: rivers, canals, drains, and precipitation. This research aims to apply numerical models for a real case study (Bahr El Baqar drain) in the Eastern Nile aquifer to monitor groundwater quality due to the use of wastewater from drains directly in irrigation due to the shortage of freshwater in this area. In addition, the effect of over-pumping from the aquifer is studied to show the extent of contaminants in groundwater. Moreover, a management strategy was achieved through mixing treated wastewater with freshwater to reduce the contamination of groundwater and overcome water shortage. Visual MODFLOW is used to simulate groundwater flow and contaminant transport into the Eastern Nile aquifer (ENDA), Egypt. In this study, three stages including 15 scenarios (five scenarios for each stage) were settled to achieve the study objectives. The first stage was carried out to investigate the impact of using untreated wastewater for irrigation due to the shortage of freshwater in this area. The results of this stage showed that increasing the use of untreated wastewater increased the contamination of the aquifer. The average COD concentrations in the five scenarios reached 23.73, 33.76, 36.49, 45.13, and 53.15 mg/L. The second stage was developed to evaluate the impact of over-pumping and using untreated wastewater for irrigation due population increase and a reduction of freshwater in the Nile Delta. The results revealed that over-pumping has increased the contamination of the aquifer and the average COD concentrations increased to 25.3, 33.34, 40.66, 48.6, and 54.17 mg/L. The third stage was applied to investigate the impact of mixing treated wastewater with freshwater for irrigation to support the freshwater quantity. The results of this stage led to enhanced water quality in the aquifer and the average COD concentrations decreased to 20.26, 23.13, 26.03, 30, and 32.83 mg/L. The results showed that mixing freshwater with treated wastewater has a good influence on water quality, can be safely used in irrigation and reduces the effects on farmers' health and life.

Activated Carbon-Loaded Titanium Dioxide Nanoparticles and Their Photocatalytic and Antibacterial Investigations

Activated carbon doping TiO2 nanoparticles were synthesised by zapota leaf extract using the co-precipitation method. The bio-constituents of plant compounds were used in the reactions of stabilization and reductions. The carbon loading on the TiO2 nanoparticles was characterised by XRD, FTIR, UV-DRS, SEM with EDX, and TEM analysis. The loading of activated carbon onto the TiO2 nanoparticles decreased the crystallite size and optical bandgap, and their doping improved the surface structure of AC/TiO2 nanoparticles. Mesoporous/microporous instability was remodified from the activated carbon, which was visualised using SEM and TEM analysis, respectively. The photocatalytic dye degradation of Rh-B dye was degraded in TiO2 and AC/TiO2 nanoparticles under visible light irradiation. The degradation efficiencies of TiO2 and AC/TiO2 nanoparticles were 73% and 91%, respectively. The bacterial abilities of TiO2 and AC/TiO2 nanoparticles were examined by E. coli and S. aureus. The water reclamation efficiency and bactericidal effect of TiO2 and AC/TiO2 nanoparticles were examined via catalytic dye degradation and bacterial efficiency of activated carbon-doped titanium dioxide nanoparticles.

Sequencing Batch Reactor Performance Evaluation on Orthophosphates and COD Removal from Brewery Wastewater

The discharge of industrial effluent constituting high orthophosphates and organic pollutants in water receiving bodies compromises freshwater quality and perpetuates eutrophication. In this study, an anaerobic–aerobic sequencing batch reactor (SBR) under activated sludge was investigated for orthophosphates and chemical oxygen demand (COD) removal from brewery wastewater. Raw brewery wastewater samples were collected on a daily basis for a period of 4 weeks. The findings of the study are reported based on overall removal efficiencies recording 69% for orthophosphates and 54% for total COD for a sludge retention time (SRT) of 7 days and hydraulic retention time of 18 h at mesophilic temperature conditions of ±25 °C. Moreover, the SBR system showed stability on orthophosphate removal at a SRT ranging from 3 to 7 days with a variation in organic volumetric loading rate ranging from 1.14 to 4.83 kg COD/m3.day. The anaerobic reaction period was experimentally found to be 4 h with the aerobic phase lasting for 14 h. The SBR system demonstrated feasibility on orthophosphates and COD removal with variation in organic loading rate.

Biodiversity Conservation of National Parks and Nature-Protected Areas in West Africa: The Case of Kainji National Park, Nigeria

Due to rising global warming and climate change, biodiversity protection has become a critical ecological concern. Rich biodiversity zones are under threat and are deteriorating, necessitating national, regional, and provincial efforts to safeguard these natural areas. The effective conservation of national parks and nature-protected areas help to improve biodiversity conservation, forest, and urban air quality. The continuous encroachment and abuse of these protected areas have degraded the ecosystem over time. While exploring the geophysical ecology and biodiversity conservation of these areas in West Africa, Kainji National Park was selected for this study because of its notable location, naturalness, rich habitat diversity, topographic uniqueness, and landmass. The conservation of national parks and nature-protected areas is a cornerstone of biodiversity conservation globally. This study is aimed at the target United Nations’ Sustainable Development Goal 13, 2030—Climate Action targeted at taking urgent action towards combating climate change and its impacts. The study captures both flora and fauna that are dominant in the study area. The 15 identified tree species were selected from over 30 species with 563,500,000 (an average of 3,700,000 in each sample frame) trees for every tree species/type with a total of 63% tree green canopy cover. The study areas divided into three zones were randomly sampled within a stratum of 25 × 25 km frames divided into 150 sample frames for proper analyses using the i-Tree Eco v6.0.25. It is a United States Department of Agriculture (USDA) Forest Service peer-reviewed application (software) designed which includes tools for urban and rural forestry study and benefits evaluations. The following microclimatic data were captured and analyzed photosynthetically active radiation, rain/precipitation, temperature, transpiration, evaporation, water intercepted by trees, runoff avoided by trees, potential evaporation by trees, and isoprene and monoterpene by trees. This study also further discusses the tree benefits of a green, low carbon, and sustainable environment within the context of biodiversity conservation, considering carbon storage, carbon sequestration, hydrology effects, pollution removal, oxygen production, and volatile organic compounds (VOCs). There is a quick need for remotely-sensed information about the national parks, protected areas and nature reserves at regular intervals, and government policies must be strict against illegal poaching, logging activities, and other hazardous human impacts.

Numerical Canal Seepage Loss Evaluation for Different Lining and Crack Techniques in Arid and Semi-Arid Regions: A Case Study of the River Nile, Egypt

Owing to the potential negative impacts of climatic changes and the grand Ethiopian renaissance dam, water scarcity has become an urgent issue. Therefore, the Egyptian Ministry of Water Resources and Irrigation has started a national project of the lining and rehabilitation of canals, to reduce seepage losses and for efficient water resource management. This study presents a new approach for assessing three different lining and crack techniques for the Ismailia canal, the largest end of the river Nile, Egypt. A 2-D steady state seep/w numerical model was developed for the Ismailia canal section, in the stretch at 28.00–49.00 km. The amount of seepage was significantly dependent on the hydraulic characteristics of the liner material. The extraction from aquifers via wells also had a considerable impact on the seepage rate from the unlined canals; however, a lesser effect was present in the case of lined canals. The concrete liner revealed the highest efficiency, followed by the geomembrane liner, and then the bentonite liner; with almost 99%, 96%, and 54%, respectively, without extraction, and decreasing by 4% for bentonite and geomembrane liners during extraction; however, the concrete lining efficiency did not change considerably. Nevertheless, the efficiency dramatically decreased to 25%, regardless of the lining technique, in the case of deterioration of the liner material. The double effect of both deterioration of the liner material and extraction from the aquifer showed a 16% efficiency, irrespective of the utilized lining technique.