Solar photocatalytic degradation of mono azo methyl orange and diazo reactive green 19 in single and binary dye solutions: adsorbability vs photodegradation rate

Insights into the structures and properties of dyes in the Fenton catalytic process for treating wastewater effluent

A notable level of apprehension exists over the adverse impacts of dye pollution on aquatic ecosystems and human well-being. The primary objective of this research is to assess the effectiveness of Fenton catalytic reactions in degrading 14 different commercial azo dyes (both single and double) present in aqueous solutions. The investigation focused on the function of dye structures, using a combination of experimental data and examination of theoretical factors. Dye degradation process was carried out at pH 3, and the concentrations of Fe2+ (10-4  mol/L), H2 O2 (2 × 10-3  mol/L), and dye (0.05 g/L). The findings revealed that dyes with a larger molecular weight were more effective at degrading (D%), with the overall degradation efficiency varying from 0% to 94%. Functional groups played an important role in degradation efficiency; for example, dyes with higher aromatic rings led to less D%, while a higher number of sulfonic, methyl, and nitro groups was responsible for better D%. Notably, the presence of OH groups in the backbone of dyes (AB 24, ABE 113, and MB 9) formed the Fe complex during the catalytic process, and the D% was minimal. On the other hand, theoretical quantum calculations such as the greater the JCLogP, highest occupied molecular orbital, and Dipole moment value, the higher the degradation efficiency. And dyes with low lowest unoccupied molecular orbital tended to have a better degradation efficiency. To some extent, UV-Vis spectral analysis was investigated to determine the degradation pathway, and the pseudo-second-order kinetic model fitted better in the degradation process. The overall experimental and theoretical findings suggested that dye degradation efficiency by the Fenton process is structure-dependent. PRACTITIONER POINTS: Insights into the role of azo dye structures-properties on degradation efficiency. Higher molecular weight and sulfonic groups containing dyes showed better degradation efficiency. Hydroxyl groups play the formation of the Fe complex during the degradation process. Higher values of HOMO and lower values of LUMO enhanced degradation efficiency. The pseudo-second-order (PSO) kinetic model obeyed the Fenton process.

Boosted photocatalytic effect of binary AgI/Ag2WO4 nanocatalyst: characterization and kinetics study towards ceftriaxone photodegradation

In modern chemistry, great interest has been paid to introducing outstanding photocatalysts for degrading organic pollutants. Herein, a highly efficient binary AgI/Ag₂WO₄ photocatalyst was prepared from AgI and Ag₂WO₄ nanoparticles (NPs) and characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), UV-Vis diffuse reflectance spectroscopy (DRS), electrochemical impedance spectroscopy (EIS), and Fourier transform infrared (FT-IR) techniques. In the Scherrer model, the average crystallite sizes of 34.9, 42.0, and 24.1 nm were estimated for the AgI, Ag₂WO₄, and the binary catalyst, while the values were 91, 13, and 85 nm by the Williamson-Hall model. FTIR confirmed the presence of W-O-W, O-W-O, Ag-I, and O-Ag-O bonds in the coupled material. DRS results showed absorption edge wavelengths of 451, 462, and 495 nm (corresponding to the band gap values of 2.75, 2.68, and 2.51 eV) for Ag₂WO₄, AgI, and AgI/Ag₂WO₄ catalyst, respectively. Synergistic photocatalytic activity of the coupled system was achieved towards ceftriaxone (CTX) in an aqueous solution (about 33% 10 ppm CTX solution was degraded without any optimization in the initial conditions of catal dose 0.3 g/L (Ag₂WO₄:AgI with mole ratio 1:2 and 30 min abrasion time), and irrad. time 45 min, C_CTX). This boosted effect depended on the AgI:Ag₂WO₄ mole ratio and grinding time for the mechanical preparation of the binary catalyst (optimums: mole ratio of 4:1 and time 30 min). The photodegradation kinetics obeyed the Hinshelwood model with the apparent first-order rate constant (k) of 0.013 min^-1 (t_1/2 = 53.30 min). Performing the COD on the photodegraded CTX solutions got a Hinshelwood plot with a slope of 0.019 min^-1 (t_1/2 = 36.5 min).

Revealing the influences of functional groups in azo dyes on the degradation efficiency and power output in solar photocatalytic fuel cell

In this study, the degradation efficiency and electricity generation of the azo dyes affected by the functional groups and molecular structure in a solar photocatalytic fuel cell (PFC) system were investigated and discussed in detail. Four different azo dyes such as, Acid Orange 7 (AO7), Acid Red 18 (AR18), Reactive Black 5 (RB5), Reactive Red 120 (RR120) with different molecular structure were evaluated. The degradation efficiency of AO7, AR18, RB5 and RR120 achieved 5.6 ± 0.3%, 11.1 ± 0.6%, 41.9 ± 0.9% and 52.1 ± 1.3%, respectively, after 6 h irradiated under solar light. In addition, the maximum power density, P_max for AO7, AR18, RB5 and RR120 was 0.0269 ± 0.01, 0.111 ± 0.03, 1.665 ± 0.67 and 4.806 ± 1.79 mW cm^-2, respectively. Meanwhile, the concentration of COD for AO7, AR18, RB5 and RR120 reduced to 16 ± 0.1, 10 ± 0.3, 7 ± 0.6 and 3 ± 0.9 mg L^-1, respectively. The concentration ratio of benzene / naphthalene, benzene / azo bond and naphthalene / azo bond, respectively, was analyzed to investigate the impact of the functional groups over photodegradation of the azo dyes in PFC. Electron releasing groups (-OH and -NH₂) and electron withdrawing groups (-SO₃Na) which attached to the naphthalene or benzene ring also played a pivotal role in the degradation mechanism.

Intensified Photocatalytic Degradation of Solophenyl Scarlet BNLE in Simulated Textile Effluents Using TiO2 Supported on Cellulosic Tissue

The Heterogeneous photocatalysis, increasingly used in effluent purification, is attracting more and more attention by the development of new photocatalytic materials based on semiconductors deposited on various supports. In this work, TiO2 supported on cellulosic fiber was prepared and characterized by different analytical techniques such as X-ray Photoelectron Spectrometry and Brunauer-Emmett-Teller surface area. Its photocatalytic activity was investigated for the degradation of Solophenyl Scarlet BNLE (SS), an organic pollutant present in textile effluents. Several conditions were investigated such as adsorption under UV and visible irradiation, catalyst recyclability, the simulated effluent pH and the presence of H2O2 as an oxidant agent. Results showed that under UV light, the removal of SS decreased significantly with increasing initial dye concentration. For an initial concentration of 5 mg/L, SS degradation was reached more than 95 % after 2 hours of treatment (neutral pH, T = 20 °C). The supported TiO2 on cellulose remains effective over four cycles of dye treatment. In the presence of H2O2, the degradation process was inhibited with increasing the molar ratio [H2O2]/[SS]0 from 5 to 30. The kinetic modeling showed that the removal of this pollutant followed a pseudo-first-order model (Langmuir-Hinshelwood) with a regression coefficient (R2) value of 0.984.

A comparative study in single- and binary-contaminant systems: the photodegradation of tetracycline and imidacloprid on flower-shaped Ag/AgBr/BiOBr under visible-light irradiation

A synergistic effect demonstrated in binary-contaminant systems is shown to be caused by the mutually complementary utilization of active species during photodegradation.

Solar photocatalytic degradation of textile effluent with TiO2, ZnO, and Nb2O5 catalysts: assessment of photocatalytic activity and mineralization

The photocatalytic degradation of textile effluent was investigated using TiO₂, ZnO, and Nb₂O₅ catalysts under solar irradiation. The procedures were carried out at ambient conditions in April 2014, with pH 3.0 and catalyst concentration of 0.250 g L^-1. The photocatalytic activity of the oxides was evaluated by means of kinetic efficiency (rate constant and half-life time), chemical oxygen demand reduction, and absorbance reduction at 228, 254, 284, 310, 350, 500, and 660 nm (λ_máx). Mineralization in terms of the formation of inorganic ions and toxicity reduction using bioassays with Artemia salina were performed. TiO₂ reduced the absorbance at 660 nm (λ_max) after 300 min of solar irradiation around 94 and 93%; and 68 and 60% of COD, respectively. ZnO showed lower photocatalytic activity giving 64 and 42% of absorbance and COD reduction, respectively. The photocatalytic activity of Nb₂O₅ was very close to TiO₂-P25. In this sense, Nb₂O₅ becomes a promising alternative to replace the commercial TiO₂-P25. Bioassays confirmed the efficacy of treatment, increasing the lethal concentration of 27.59 (in natura) to 131.95% in the presence of Nb₂O₅.

Degradation of Methyl Orange and Congo Red dyes by using TiO2 nanoparticles activated by the solar and the solar-like radiation

In this study we used TiO2 nanoparticles as semiconductor photocatalysts for the degradation of Methyl Orange (MO) and Congo Red (CR) dyes in an aqueous solution. Since TiO2 particles become photocatalytically active by UV radiation, two sources of UV-A radiation were used - natural solar radiation which contains 3-5% UV-A and artificial, solar-like radiation, created by using a lamp. The optimal doses of TiO2 of 500 mg/L for the CR and 1500 mg/L for the MO degradation were determined in experiments with the lamp and were also used in degradation experiments with natural solar light. The efficiency of each process was determined by measuring the absorbance at two visible wavelengths, 466 nm for MO and 498 nm for CR, and the total organic carbon (TOC), i.e. decolorization and mineralization, respectively. In both cases, considerable potential for the degradation of CR and MO was observed - total decolorization of the solution was achieved within 30-60 min, while the TOC removal was in the range 60-90%. CR and MO solutions irradiated without TiO2 nanoparticles showed no observable changes in either decolorization or mineralization. Three different commercially available TiO2 nanoparticles were used: pure-phase anatase, pure-phase rutile, and mixed-phase preparation named Degussa P25. In terms of degradation kinetics, P25 TiO2 exhibited a photocatalytic activity superior to that of pure-phase anatase or rutile. The electric energy consumption per gram of removed TOC was determined. For nearly the same degradation effect, the consumption in the natural solar radiation experiment was more than 60 times lower than in the artificial solar-like radiation experiment.

Visible-light-responsive t-Se nanorod photocatalysts: synthesis, properties, and mechanism

One-dimensional (1D) single-crystalline trigonal selenium nanorods (t-Se NRs) were prepared through a “solid–solution–solid” method by dispersing the prepared amorphous α-Se spheres in ethanol.