Novel organic assisted Ag-ZnO photocatalyst for atenolol and acetaminophen photocatalytic degradation under visible radiation: performance and reaction mechanism

The Solvent Role for the Decomposition of Paracetamol in Distilled and Drinking Water by Pure and Ag-Modified TiO2 Sol-Gel Powders

In this study, pure TiO2 gels were synthesized by applying the sol-gel method, using Ti(IV) butoxide with the addition of two different solvents, namely ethylene glycol (EG) and isopropanol (isop), with only air moisture present. It was established using XRD that the gel prepared with the addition of EG was amorphous even at 400 °C, while the other gel was amorphous up to 300 °C. It was found that TiO2 (anatase) had a dominant crystalline phase during heating to 600 °C, while at 700 °C, TiO2 (rutile) appeared. The as-obtained powdered materials were annealed at 500 °C and subsequently underwent photocatalytic tests with paracetamol. Additionally, the TiO2 samples were modified with Ag+ co-catalysts (10-2 M), using photofixation by UV illumination. The photocatalytic activity of the Ag-modified powders was also tested in the photodegradation of a commonly used paracetamol in aqueous solution under UV light illumination. The obtained data exhibited that the annealed samples had better photocatalytic efficiency and decomposed paracetamol faster in comparison to the non-annealed sol-gel powders. The highest degradation efficiency was observed for the TBT/isop/Ag material, with degradation efficiencies average values of 65.59% and 75.61% paracetamol achieved after the third cycle of photocatalytic treatment. The co-catalytically modified powders had higher photocatalytic efficiency in comparison to the pure nanosized powders. Moreover, the sol-gel powders of TBT/EG, TBT/EG/Ag (10-2 M), TBT/isop, and TBT/isop/Ag (10-2 M) demonstrated the ability to retain their photocatalytic activity even after three cycles of use, suggesting that they could find practical use in the treatment of pharmaceutical wastewater. The observed photocatalytic efficiency and positive impact of silver make the prepared powders a desirable choice for pharmaceutical drug degradation, helping to promote environmentally friendly and effective wastewater treatment technology.

SU-101 for the removal of pharmaceutical active compounds by the combination of adsorption/photocatalytic processes

Pharmaceutical active compounds (PhACs) are some of the most recalcitrant water pollutants causing undesired environmental and human effects. In absence of adapted decontamination technologies, there is an urgent need to develop efficient and sustainable alternatives for water remediation. Metal-organic frameworks (MOFs) have recently emerged as promising candidates for adsorbing contaminants as well as providing photoactive sites, as they possess exceptional porosity and chemical versatility. To date, the reported studies using MOFs in water remediation have been mainly focused on the removal of a single type of PhACs and rarely on the combined elimination of PhACs mixtures. Herein, the eco-friendly bismuth-based MOF, SU-101, has been originally proposed as an efficient adsorbent-photocatalyst for the elimination of a mixture of three challenging persistent PhACs, frequently detected in wastewater and surface water in ng L-1 to mg·L-1 concentrations: the antibiotic sulfamethazine (SMT), the anti-inflammatory diclofenac (DCF), and the antihypertensive atenolol (At). Adsorption experiments of the mixture revealed that SU-101 exhibited a great adsorption capacity towards At, resulting in an almost complete removal (94.1 ± 0.8% for combined adsorption) in only 5 h. Also, SU-101 demonstrated a remarkable photocatalytic activity under visible light to simultaneously degrade DCF and SMT (99.6 ± 0.4% and 89.2 ± 1.4%, respectively). In addition, MOF-contaminant interactions, the photocatalytic mechanism and degradation pathways were investigated, also assessing the toxicity of the resulting degradation products. Even further, recycling and regeneration studies were performed, demonstrating its efficient reuse for 4 consecutive cycles without further treatment, and its subsequent successful regeneration by simply washing the material with a NaCl solution.

Morinda citrifolia leaf assisted synthesis of ZnO decorated Ag bio-nanocomposites for in-vitro cytotoxicity, antimicrobial and anticancer applications

This study used Morinda citrifolia leaf (MCL) extract to synthesise Zinc oxide nanoparticles (ZnO NPs) and ZnO decorated silver nanocomposites (ZnO/Ag NCs). The synthesized nanomaterials structural morphology and crystallinity were characterized using a Field emission scanning electron microscope (FESEM) and X-ray diffraction (XRD) analysis. The antimicrobial activity of ZnO NPs and ZnO/Ag NCs was evaluated using human nosocomial bacterial pathogens. The highest antimicrobial activity was recorded for ZnO/Ag NCs at the minimum inhibitory concentration (MIC) at 80 and 100 μg/mL for Escherichia coli, Pseudomonas aeruginosa and Bacillus subtilis, Staphylococcus aureus than ZnO NPs at the MIC of 120 and 140 μg/mL for Bacillus subtilis and Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus. Furthermore, ROS detection, viability assay and bacterial membrane integrity analysis of ZnO/Ag NCs treated P. aeruginosa and S. aureus revealed the fundamental bactericidal mechanism involving cell wall, cell membrane interaction and release of cytoplasmic contents. In addition, ZnO/Ag NCs and ZnO NPs showed higher toxicity towards A549 lung cancer cells than the non-cancerous RAW264 macrophage cells, with IC50 of 242 and 398 µg/mL respectively, compared to IC50 of 402 and 494 µg/mL for the macrophage cells. These results suggest that the ZnO/Ag NCs can be effectively used to develop antimicrobial and anticancer materials.

Recent updates on remediation approaches of environmentally occurring pollutants using visible light-active nano-photocatalysts

Photocatalysis emerges as a potential remedy for the issue of an unreliable light source. Recognized as the most dependable and potent energy source sustaining life on Earth, sunlight offers a promising solution. Sunlight is abundant and free, operational costs associated with running photocatalytic system using nanoparticles are often lower compared to system relying on artificial light source. The escalating problem of water pollution, particularly in highly industrialized nations, necessitates effective wastewater treatment methods. These methods aim to combat elevated pollution levels, encompassing pharmaceuticals, dyes, flame retardants, and pesticide components. Advanced oxidation processes within photocatalytic wastewater treatment exhibit substantial promise for removing complex organic pollutants. Doped nanomaterials, with their enhanced properties, enable efficient utilization of light. Coupled nanomaterials present significant potential in addressing both water and energy challenges by proficiently eliminating persistent pollutants from environment. Photocatalysis when exposed to sunlight can absorb photons and generate e- h + pairs. This discussion briefly outlines the wastewater treatment facilitated by interconnected nanomaterials, emphasizing their role in water-energy nexus. In exploring the capabilities of components within a functional photocatalyst, a comprehensive analysis of both simple photocatalysts and integrated photocatalytic systems is undertaken. Review aims to provide detailed explanation of the impact of light source on photon generation and significance of solar light on reaction kinetics, considering various parameters such as catalyst dosage, pH, temperature, and types of oxidants. By shedding light on these aspects, this review seeks to enhance our understanding of intricate processes involved in photocatalysis and its potential applications in addressing contemporary environmental challenges.

Back to nature: henna extracts from nanotech to environmental biotechnology - a review

The Lythraceae family includes henna (Lawsonia inermis), which thrives in subtropical and tropical climates. One of its many and long-standing uses is in cosmetics as a pigment to color hair and nails. Additionally, it serves as a disinfectant against microbiological infections and has traditional applications in the textile industry, specifically for coloring wool and nylon. The dried leaves of henna contain a significant amount of lawsone, an active substance bestowing them with staining abilities. Environmental biotechnology, a subfield of biotechnology, engages in the production of biomass or renewable energy sources and the elimination of pollutants, utilizing either entire organisms or their by-products. Recent research indicates that henna, owing to its sustainability, abundant production, simplicity of preparation, low cost, and reputation for being safe and ecologically benign, is exceptionally well-suited to participate in the realm of environmental biotechnology. This review navigates through the most recent studies exploring the use of henna and its extracts for related purposes. These encompass a spectrum of applications, including but not limited to nanobiotechnology, fabric dyeing, corrosion resistance, colored solar cells, carbon dots, and new renewable energy exemplified by biofuel and biohydrogen. Furthermore, henna extracts have been deployed to function as antimicrobials and ward off dangerous insects.

ZnO nanostructured matrix as nexus catalysts for the removal of emerging pollutants

Water pollution stands as a pressing global environmental concern, elevating the significance of innovative, dependable, and sustainable solutions. This study represents an extensive review of the use of photocatalytic zinc oxide nanoparticles (ZnO NPs) for the removal of emerging pollutants from water and wastewater. The study examines ZnO NPs' different preparation methods, including physical, chemical, and green synthesis, and emphasizes on advantages, disadvantages, preparation factors, and investigation methods for the structural and morphological properties. ZnO NPs demonstrate remarkable properties as photocatalysts; however, their small dimensions pose an issue, leading to potential post-use environmental losses. A strategy to overcome this challenge is scaling up ZnO NP matrices for enhanced stability and efficiency. The paper introduces novel ZnO NP composites, by incorporating supports like carbon and clay that serve as photocatalysts in the removal of emerging pollutants from water and wastewater. In essence, this research underscores the urgency of finding innovative, efficient, and eco-friendly solutions for the removal of emerging pollutants from wastewater and highlights the high removal efficiencies obtained when using ZnO NPs obtained from green synthesis as a photocatalyst. Future research should be developed on the cost-benefit analysis regarding the preparation methods, treatment processes, and value-added product regeneration efficiency.

High efficient COVID-19 waste co-pyrolysis char/TiO2 nanocomposite for photocatalytic reduction of Cr(VI) under visible light

Titanium dioxide (Titania) nanoparticle-coated biochar derived through co-pyrolysis of COVID-19 waste face mask (WFM) and Moringa oleifera seed cake (MO) provides an effective way to alleviate toxic metal in wastewater. This study investigates the effects of Biochar/titania photocatalyst preparation, characterization, and its photoreduction of Cr(VI). The morphological and functional modifications in the catalyst were identified using X-Ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, ultraviolet spectrophotometer, surface area analysis, and Raman spectrophotometer, respectively. The influencing parameters, namely, pH, photocatalyst dosage, initial pollutant concentration, and visible light irradiation time, have been investigated. The findings reveal that the Cr(VI) reduction by the photocatalyst was highly facilitated by photocatalytic process. The prepared photocatalyst shows higher and faster reduction rate of Cr(VI) and also improves the catalyst stability. The photoreduction of Cr(VI) ensembles well with pseudo-first order kinetics. At 180 min of reaction time, maximum Cr(VI) reduction of 98.65% was achieved at pH 2, 0.3 g/L catalyst dosage, and 10 ppm initial concentration, respectively. The synthesized photocatalyst shows excellent recycling performance up to 7 times, and these studies proved that the prepared catalyst is cost-effective and efficiently employed for removing pollutants.

Photocatalytic Degradation of Acetaminophen in Aqueous Environments: A Mini Review

Over the past few decades, acetaminophen (ACT), a typical nonsteroidal anti-inflammatory drug (NSAID), has gained global usage, positioning itself as one of the most extensively consumed medications. However, the incomplete metabolism of ACT leads to a substantial discharge into the environment, classifying it as an environmental contaminant with detrimental effects on non-target organisms. Various wastewater treatment technologies have been developed for ACT removal to mitigate its potential environmental risk. Particularly, photocatalytic technology has garnered significant attention as it exhibits high efficiency in oxidizing and degrading a wide range of organic pollutants. This comprehensive review aims to systematically examine and discuss the application of photocatalytic technology for the removal of ACT from aqueous environments. Additionally, the study provides a detailed overview of the limitations associated with the photocatalytic degradation of ACT in practical applications, along with effective strategies to address these challenges.

Conversion of novel tannery sludge-derived biochar/TiO2 nanocomposite for efficient removal of Cr (VI) under UV light: photocatalytic performance and mechanism insight

An investigation on the reduction of Cr (VI) pollutant from tannery effluents using TiO₂, SB/TiO₂, and c-SB/TiO₂ nano photocatalysts was presented in this study. For the preparation of Biochar-based TiO₂ photocatalyst (SB/TiO₂), tannery sludge was utilized as a precursor. Hydrothermal pre-treatment was adopted to prepare chemically activated SB/TiO₂ and SB/TiO₂ nanocomposites. The morphology, crystal structure, optical properties, and elemental composition of the prepared catalysts were analyzed by XRD, FT-IR, SEM-EDX, BET analysis, ZPC, PL, TGA, and Raman spectroscopy. The band gap analysis of Photocatalyst was measured using a DRS instrument, and band gap energy of 3.39 eV was obtained for c-SB/TiO₂ photocatalyst. The developed c-SB/TiO₂ catalyst exhibits a larger specific surface area of 646.85 m²/g than TiO₂ and SB/TiO₂ (74.58 m²/g and 573.74 m²/g), respectively. The enhanced photocatalytic activity for the pollutant removal was achieved by the photocatalyst due to their wide band gap and effective charge separation. The kinetic rate constant was achieved in the pseudo-first-order model, which fits well for the reduction of Cr (VI). Furthermore, at the optimal conditions of 10 mg/L contaminant concentration, pH 2, and 0.5 g/L catalyst dosage, 98.56% reduction was observed after 180 min of reaction. The OH acts as a major removal pathway for Cr (VI) contaminants with more than 50% reduction in COD. This study proves that c-SB/TiO₂ photocatalysts can remove toxic contaminants under UV light irradiation with good recycling performance up to 5 times.

Design and modeling of diazinon degradation in hydrous matrix by Ni-doped ZnO nanorods under ultrasonic irradiation: process optimization using RSM (CCD), kinetic study, reaction pathway, mineralization, and toxicity assessment

In first, the Ni-doped ZnO nanorods used as an appeal sonocatalyst was synthesized through co-precipitation method. Afterwards, the crystalline structure, functional groups, surface morphology, and elemental composition were characterized by a set of analysis. Removal of diazinon ((DZ) as a renowned pesticide) was investigated using sonocatalytic performance of US/Ni-doped ZnO system. In this empirical study, response surface methodology (RSM) based central composite design (CCD) was applied for optimization of operational factors. Under the optimum conditions such as initial pH = 5, initial DZ concentration = 15 mg L^-1, sonocatalyst dosage = 1 g L^-1, and in the presence of organic compounds (oxalic acid, humic acid, and folic acid) = 3 mg L^-1, the sonocatalytic degradation of DZ after 15 min was 82.29%. The F-value (6.64) and P-value (< 0.0001) for DZ degradation in the quadratic model imply the proposed model was significant. A-factor (pH) considers as a prominent factor owing to having the highest F-value. In addition, the sonocatalytic data in this study exhibited valid fitting for the first order kinetic model (R² > 0.98). After six consecutive cycles, the Ni-doped ZnO nanorods could be recyclable for sonocatalytic degradation of DZ. The five main compounds produced during the US/Ni-doped ZnO embracing 2-isopropyl-6-methyl-4-pyrimidinol (IMP), diethyl phosphonate, diazoxon, hydroxyldiazinon, and diazinon methyl ketone are formed in the path of DZ degradation. OFAT style also revealed 99.99% of DZ degradation with 73.26% of mineralization rate in optimum status. The Ni-doped ZnO presented agreeable sonocatalytic facility in the refinement of real water and wastewater matrix. Finally, the results of toxicity evaluation (Daphnia magna) in the sonocatalytic degradation of DZ (by US/Ni-doped ZnO system) showed that the toxicity of the DZ solution lessened under US waves (LC₅₀ and TU 48 h equal to 36.472 and 2.741 volume percent, respectively).

pH dependent synthesis and characterization of bismuth molybdate nanostructure for photocatalysis degradation of organic pollutants

Bismuth molybdate (Bi₂MoO₆) nanostructures has attracted many researches as an advanced photocalysts for the organic contaminants. In this paper, bismuth molybdate Bi₂MoO₆ nanoparticles were synthesized using a simple hydrothermal method at varied pH (2, 4, 6, 8, and 10) for 15 h at 180 °C. The results reveal the variation pH precursor solutions have a significant impact on the morphology, phase formations, and photocatalytic activity of samples. The synthesized samples at low pH level were characterized by FESEM analysis revealing Bi₂MoO₆ nanoplates have formed while gradually convert to Bi₂MoO₆ spherical nanoparticle at high PH level as shown in energy dispersive X-ray spectroscopy (DES) peaks. The X-ray diffraction patterns reveal characteristic peaks corresponding to mixed phases of Bi₂MoO₆ and cubic Bi₄MoO₉ at high pH value. The optical absorption study exhibit Bi₂MoO₆ nanoplates absorbed visible light with blue shift when compared to the cubic Bi₄MoO₉ structures. Moreover, the photocatalytic activity results revealed that nanoplates in pH = 4 sample has excellent photocatalytic activity for degradation of rhodamine (RhB), methylene orange (MO), and phenol under visible-light irradiation (λ > 400 nm) as well as exhibit the photodegradation 90% of phenol within 300 min.

Plant-Based Bimetallic Silver-Zinc Oxide Nanoparticles: A Comprehensive Perspective of Synthesis, Biomedical Applications, and Future Trends

The universal emphasis on the study of green nanotechnology has led to biologically harmless uses of wide-ranged nanomaterials. Nanotechnology deals with the production of nanosized particles with regular morphology and properties. Various researches have been directed on nanomaterial synthesis by physical, chemical, and biological means. Understanding the safety of both environment and in vivo, a biogenic approach particularly plant-derived synthesis is the best strategy. Silver-zinc oxide nanoparticles are most effective. Moreover, these engineered nanomaterials via morphological modifications attain improved performance in antimicrobial, biomedical, environmental, and therapeutic applications. This article evaluates manufacturing strategies for silver-zinc oxide nanoparticles via plant-derived means along with highlighting their broad range of uses in bionanotechnology.

MoS2/N-TiO2/Ti mesh plate for visible-light photocatalytic ozonation of naproxen and industrial wastewater: comparative studies and artificial neural network modeling

This paper presents the results of visible-light assisted photocatalytic ozonation for the degradation of naproxen as a model pharmaceutical pollutant from water using MoS₂/N-TiO₂ immobilized on a titanium mesh plate in addition to treatment of a real industrial wastewater. The batch studies were performed for naproxen degradation by varying the reaction variables such as ozone flow rate, initial pH and pollutant concertation. It was observed that almost 90% degradation was achieved at pH = 4, ozone flow rate = 3 L min^-1 and initial naproxen concentration = 5 mg L^-1. The catalyst exhibited constant activity even after seven successive cycles. Comparative studies among sorption, ozonation, photocatalysis, catalytic ozonation and photocatalytic ozonation revealed that the later process had the highest degradation of pollutant. Moreover, an artificial neural network (ANN) model was developed to simulate the performance of visible-light photocatalytic ozonation in naproxen degradation. The developed ANN model could estimate the visible-light photocatalytic ozonation process under the different experimental conditions. Finally, the applicability of the photocatalytic ozonation was successfully approved for industrial wastewater treatment. The results showed that the COD removal efficiency reached 65% within 150 min. HIGHLIGHTS: • MoS₂/N-TiO₂/Ti was synthesized by the quick electrophoretic deposition method. • The catalyst showed good ability in naproxen degradation via visible-light photocatalytic ozonation. • A three-layer artificial neural network model was developed to predict the naproxen degradation. • Naproxen degradation efficiency through the photocatalytic ozonation was higher than the individual methods. • COD of real wastewater was reduced significantly after the visible-light photocatalytic ozonation process.

Solar light-driven photocatalytic degradation and mineralization of beta blockers propranolol and atenolol by carbon dot/TiO2 composite

Herein improved solar light-driven photocatalytic degradation and mineralization of two emerging pollutants as well as recalcitrant beta blockers propranolol (PR) and atenolol (AT) have been demonstrated by metal-free carbon dot/TiO₂ (CDT) composite. Hydrothermally synthesized TiO₂ has been decorated with electrochemically synthesized carbon dots (CDs) and was well characterized by various analytical techniques viz. XRD, FTIR, Raman, XPS, UV-visible DRS, FESEM, and TEM. The optimized CDT composite, 2CDT (2 mL carbon dot/TiO₂), showed ~ 3.45- and ~ 1.75-fold enhancement in the photodegradation rate as compared to pristine TiO₂ for PR and AT respectively in 1 hour of irradiation along with complete degradation of PR and AT after 3 hours of irradiation. 2CDT exhibited 76% and 80% mineralization of PR and AT in contrast with 62% and 47% observed by pristine TiO₂. Further, the major reaction intermediates formed after degradation have been identified by HPLC/MS analysis, confirming more than 99% reduction of the parent compound for both PR and AT. Reusability of the optimized catalyst also showed successful degradation up to 3 cycles, showing reduction abilities of 97%, 95%, and 94% for 1st, 2nd, and 3rd cycle respectively. The enhanced degradation and mineralization efficiency of the 2CDT composite could be attributed to the excellent photosensitizer and electron reservoir properties of the CD along with upconverted photoluminescence behavior. The present study unlocks the possibility of using metal-free, facile CDT composite for effective degradation and mineralization of widely used beta blockers and other pharmaceuticals.

Synthesis, characterization of novel ZnO/CuO nanoparticles, and the applications in photocatalytic performance for rhodamine B dye degradation

Photocatalytic deg radation of environmental pollutants is being up to date for the treatment of contaminated water. In the present study, ZnO/CuO nanomaterials were successfully fabricated by a simple sol-gel method and investigate the photo-degradation of rhodamine B (RhB). The synthesized ZnO/CuO nanoparticles were characterized by X-ray diffraction (XRD), energy-dispersive spectroscopy (EDS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-Vis diffuse reflectance spectroscopy (UV-Vis-DRS), thermal analysis (TGA), surface charge, and Fourier transform infrared spectroscopy (FTIR). The photo-degradation of the dye RhB was followed spectroscopically. The overall composition of ZnO/CuO material was found to be wurtzite phase, with particle size of 30 nm, and the Vis light absorption increased with an increase of Cu content. The ZnO/CuO nanomaterials were highly active leading to a photo-degradation of 10 ppm RhB reaching 98% within 180 min at 0.1 g/L catalyst dosage. The change in surface charge after degradation evaluated by ζ potential measurements and the differences in functional vibration group monitored by Fourier transform infrared spectroscopy (FTIR) indicates that the RhB adsorption on the Zn₄₅Cu surface was insignificant. And scavenging experiments demonstrate that the RhB degradation by ZnO/CuO nanomaterials involves to some degree hydroxyl radicals.

Predicting the trend and utility of different photocatalysts for degradation of pharmaceutically active compounds: A special emphasis on photocatalytic materials, modifications, and performance comparison

The rapid rise in the healthcare sector has led to an increase in pharmaceutically active compounds (PhACs) in different aqueous bodies. The toxicity of the PhACs and their ability to persist after conventional treatment processes have escalated research in the field of photocatalytic treatment. Although different photocatalysts have been successful in degrading PhACs, their inherent drawbacks have severely limited their application on a large scale. A substantial amount of research has been aimed at overcoming the high cost of the photocatalytic material, low quantum yield, the formation of toxic end products, etc. Hence, to further research in this field, researchers must have a fair idea of the current trends in the application of different photocatalysts. In this article, the trends in the use of various photocatalysts for the removal of different PhACs have been circumscribed. The performance of different groups of photocatalysts to degrade PhACs from synthetic and real wastewater has been addressed. The drawbacks and advantages of these materials have been compared, and their future in the field of PhACs removal has been predicted using S-curve analysis. Zinc and titanium-based photocatalysts were efficient under UV irradiation, while bismuth and graphene-based materials exhibited exemplary performance in visible light. However, iron-based compounds were found to have the most promising future, which may be because of their magnetic properties, easy availability, low bandgap, etc. Different modification techniques, such as morphology modification, doping, heterojunction formation, etc., have also been discussed. This study may help researchers to clarify the current research status in the field of photocatalytic treatment of PhACs and provide valuable information for future research.