Bioreduction of prochiral ketones with yeast cells cultivated in a vibrating air-solid fluidized bed fermentor

On the performance of immobilized cell bioreactors utilizing a magnetic field

This review focuses on the performance of immobilized cell bioreactors utilizing a magnetic field. These reactors utilized immobilized cells on magnetic particles or beads as the solid phase. All published research papers dealing with the performance of immobilized cell bioreactors utilizing a magnetic field from the early 1960s to the present time were considered and analyzed. It was noted that many microorganisms such as Saccharomyces cerevisiae were immobilized on different supports in these reactors. These papers used the magnetic field for several purposes, mainly for the stabilization of magnetic particles to prevent their washout from the column while operating with relatively high substrate flow rates to enhance mass transfer processes. It was observed that most publications used an axial magnetic field. In addition, most of the magnetic particles were prepared by entrapment. Some comments are presented at the end of the review which show the gaps in this promising application.

Thermal denaturation: is solid-state fermentation really a good technology for the production of enzymes?

The potential for thermal denaturation to cause enzyme losses during solid-state fermentation processes for the production of enzymes was examined, using the protease of Penicillium fellutanum as a model system. The frequency factor and activation energies for the first-order denaturation of this enzyme were determined as 3.447 x 10(59) h(-1) and 364,070 Jmol(-1), respectively. These values were incorporated into a mathematical model of enzyme deactivation, which was used to investigate the consequences of subjecting this protease to temporal temperature profiles reported in the literature for mid-height in a 34 cm high packed-bed bioreactor of 150 mm diameter. In this literature source, temperature profiles were measured for 5, 15 and 25 liters per minute of air and enzyme activities were measured as a function of time. The enzyme activity profiles predicted by the model were distributed similarly, one relative to the other, as had been found in the experimental study, with substantial amounts of denaturation being predicted when the substrate temperature exceeded 40 degrees C, which occurred at the lower two airflow rates. A mathematical model of a well-mixed bioreactor was used to explore the difficulties that would be faced at large scale. It suggests that even with airflows as high as one volume per volume per minute, up to 85% of the enzyme produced by the microorganism can be denatured by the end of the fermentation. This work highlights the extra care that must be taken in scaling up solid-state fermentation processes for the production of thermolabile products.

Overview of solid state bioprocessing

Solid-state fermentation has centuries of history, but it is only in the last two decades that there has been a concerted effort to understand the bioprocessing issues involved and to apply them to a wide range of new products. This article provides an overview of the knowledge of solid-state bioprocessing that has been gained over this time. It shows that, although significant advances have been achieved in understanding of what controls process performance, much research is still required.

Biochemical engineering aspects of solid state bioprocessing

Despite centuries of use and renewed interest over the last 20 years in solid-state fermentation (SSF) technology, and despite its good potential for a range of products, there are currently relatively few large-scale commercial applications. This situation can be attributed to the complexity of the system: Macroscale and microscale heat and mass transfer limitations are intrinsic to the system, and it is only over the last decade or so that we have begun to understand them. This review presents the current state of understanding of biochemical engineering aspects of SSF processing, including not only the fermentation itself, but also the auxiliary steps of substrate and inoculum preparation and downstream processing and waste disposal. The fermentation step has received most research attention. Significant advances have been made over the last decade in understanding how the performance of SSF bioreactors can be controlled either by the intraparticle processes of enzyme and oxygen diffusion or by the macroscale heat transfer processes of conduction, convection, and evaporation. Mathematical modeling has played an important role in suggesting how SSF bioreactors should be designed and operated. However, these models have been developed on the basis of laboratory-scale data and there is an urgent need to test these models with data obtained in large-scale bioreactors.