Optimization of a microwave-assisted extraction large-volume injection and gas chromatography–ion trap mass spectrometry procedure for the determination of polybrominated diphenyl ethers, polybrominated biphenyls and polychlorinated naphthalenes in sediments

First report of bioaccumulation and bioconcentration of aliphatic hydrocarbons (AHs) and persistent organic pollutants (PAHs, PCBs and PCNs) and their effects on alcyonacea and scleractinian corals and their endosymbiotic algae from the Persian Gulf, Iran: Inter and intra-species differences

The coral reefs of the Persian Gulf are the most diverse systems of life in the marine environment of the Middle East. Unfortunately, they are highly threatened by local and global stressors, particularly oil pollutants. This is the first quantitative and qualitative study aimed at assessing the concentration and sources of n-alkanes and POPs (PAHs, PCBs and PCNs) in coral tissues, symbiotic algae (zooxanthellae), reef sediments and seawaters in coral reefs of Lark and Kharg in the Persian Gulf, Iran. This work was conducted on eight species of six genera and three families of hard corals and one family of soft coral. A significant variation in the concentration of ∑30n-alkanes and POPs (∑40PAHs, ∑22PCBs and 20PCNs) was found in the decreasing order: zooxanthellae > coral tissue > skeleton > reef sediment > seawater. The bioaccumulation of these compounds was 2-times higher in ahermatypic than in hermatypic corals, among which significant variations were observed in both sites. In Kharg, Porites lutea had the highest mean concentration of ∑30n-alkanes and ∑40PAHs in soft tissue, whereas the lowest values were in Platygyra daedalea. A contrasting trend was documented for ∑22PCBs and 20PCNs, with the highest level reported in soft tissue of P. daedalea and the lowest in P. lutea at Kharg. Compositional pattern of AHs and PAHs demonstrated the predominance of LMW-PAHs and n-alkanes. In skeleton and reef sediments, tetra, penta and tri-CBs were the most abundant PCBs congeners followed by di-CB > hexa-CB > hepta-CB > octa-CB,whiletri-CB > di-CB > tetra-CB > penta-CB > hexa-CB > hepta-CB > octa-CB was observed for soft tissue, zooxanthellae and seawater. The results of RAD test indicated significantly negative correlation between total concentration of these compounds with zooxanthellae density, the chlorophyll-a and C₂ in corals at both reefs. This is the first report on levels, health assessment and source apportionments of POPs in zooxanthellae and a first step in the implementation of specific coral reef management measures.

Optimizing Mass Spectrometry Analyses: A Tailored Review on the Utility of Design of Experiments

Mass spectrometry (MS) has emerged as a tool that can analyze nearly all classes of molecules, with its scope rapidly expanding in the areas of post-translational modifications, MS instrumentation, and many others. Yet integration of novel analyte preparatory and purification methods with existing or novel mass spectrometers can introduce new challenges for MS sensitivity. The mechanisms that govern detection by MS are particularly complex and interdependent, including ionization efficiency, ion suppression, and transmission. Performance of both off-line and MS methods can be optimized separately or, when appropriate, simultaneously through statistical designs, broadly referred to as "design of experiments" (DOE). The following review provides a tutorial-like guide into the selection of DOE for MS experiments, the practices for modeling and optimization of response variables, and the available software tools that support DOE implementation in any laboratory. This review comes 3 years after the latest DOE review (Hibbert DB, 2012), which provided a comprehensive overview on the types of designs available and their statistical construction. Since that time, new classes of DOE, such as the definitive screening design, have emerged and new calls have been made for mass spectrometrists to adopt the practice. Rather than exhaustively cover all possible designs, we have highlighted the three most practical DOE classes available to mass spectrometrists. This review further differentiates itself by providing expert recommendations for experimental setup and defining DOE entirely in the context of three case-studies that highlight the utility of different designs to achieve different goals. A step-by-step tutorial is also provided.

Ultrasound leaching-dispersive liquid-liquid microextraction based on solidification of floating organic droplet for determination of polybrominated diphenyl ethers in sediment samples by gas chromatography-tandem mass spectrometry

Ultrasound leaching-dispersive liquid-liquid microextraction using solidification of floating organic droplet (USL-DLLME-SFO) technique is proposed for extraction and isolation of polybrominated diphenyl ethers (PBDEs) from sediment and further determination by gas chromatography-tandem mass spectrometry (GC-MS/MS). Parameters that affect the efficiency of the procedure were investigated by a full factorial (2(k)) screening design. Variables showing significant effects on the analytical responses were considered within a further central composite design (CCD). The optimization assays have led to following protocol: ultrasound assisted lixiviation of 1g sediment was carried out by using 1.2 mL MeOH. Further, the analytes were isolated from 0.4 mL of the extract using the DLLME-SFO technique. The microextraction was performed using 0.1 mL MeOH, 22 mg 1-dodecanol, 1 mL NaCl solution 6.15M and 4.4 mL ultrapure water as dispersive and extracting solvents, medium ionic strength and dispersant bulk, respectively. Under optimum conditions, the method exhibits good performance in terms of linearity and precision (RSD<9.2%), with recoveries above 71% and limits of detection (LODs) within the range 0.5-1.8 pgg(-1) dry weight (d.w.). Method validation was demonstrated through the analysis of environmental sediment samples in which PBDEs were detected and quantified. The presence of BDE-47, -100, -99 and -153 was reported within the concentration range of <LOD to 29 pgg(-1) d.w. The proposed methodology constitutes a suitable approach for the analysis of PBDEs in complex solid samples requires minimum organic solvents consumption, sample manipulation, and increases sample throughput.

Mass spectrometry parameters optimization for the 46 multiclass pesticides determination in strawberries with gas chromatography ion-trap tandem mass spectrometry

Multiclass analysis method was optimized in order to analyze pesticides traces by gas chromatography with ion-trap and tandem mass spectrometry (GC-MS/MS). The influence of some analytical parameters on pesticide signal response was explored. Five ion trap mass spectrometry (IT-MS) operating parameters, including isolation time (IT), excitation voltage (EV), excitation time (ET), maximum excitation energy or "q" value (q), and isolation mass window (IMW) were numerically tested in order to maximize the instrument analytical signal response. For this, multiple linear regression was used in data analysis to evaluate the influence of the five parameters on the analytical response in the ion trap mass spectrometer and to predict its response. The assessment of the five parameters based on the regression equations substantially increased the sensitivity of IT-MS/MS in the MS/MS mode. The results obtained show that for most of the pesticides, these parameters have a strong influence on both signal response and detection limit. Using the optimized method, a multiclass pesticide analysis was performed for 46 pesticides in a strawberry matrix. Levels higher than the limit established for strawberries by the European Union were found in some samples.

Analysis of emerging organic contaminants in environmental solid samples

Spreading sewage sludge on agricultural lands has been actively promoted by national authorities as an economic way of recycling. However, as by-product of wastewater treatment, sewage sludge may contain toxic substances, which could be incorporated into agricultural products or be distributed in the environment. Moreover, sediments can be contaminated by the discharge of wastewater effluents into rivers. This article reviews the determination of emerging contaminants (surfactants, flame retardants, pharmaceuticals and personal care products) in environmental solid samples (sludge, soil and sediment). Sample preparation, including extraction and clean-up, as well as the subsequent instrumental determination of contaminants are discussed. Recent applications of extraction techniques, such as Soxhlet extraction, ultrasound assisted extraction, pressurised liquid extraction, microwave assisted extraction and matrix solid-phase dispersion to the analysis of emerging contaminants in environmental solid samples are reviewed. Determination of these contaminants, generally carried out by gas chromatography and liquid chromatography coupled with different detectors, especially mass spectrometry for the identification and quantification of residues, is also summarised and discussed.

Frequency of use controls chemical leaching from drinking-water containers subject to disinfection

Microbial-, and chemical-based burden of disease associated with lack of access to safe water continues to primarily impact developing countries. Cost-effective health risk-mitigating measures, such as of solar disinfection applied to microbial-contaminated water stored in plastic bottles have been increasingly tested in developing countries adversely impacted by epidemic water-borne diseases. Public health concerns associated with chemical leaching from water packaging materials led us to investigate the magnitude and variability of antimony (Sb) and bromine (Br) leaching from reused plastic containers (polyethylene terephthalate, PET; and polycarbonate, PC) subject to UV and/or temperature-driven disinfection. The overall objective of this study was to determine the main and interactive effects of temperature, UV exposure duration, and frequency of bottle reuse on the extent of leaching of Sb and Br from plastic bottles into water. Regardless of UV exposure duration, frequency of reuse (up to 27 times) was the major factor that linearly increased Sb leaching from PET bottles at all temperatures tested (13-47 °C). Leached Sb concentrations (∼360 ng L(-1)) from the highly reused (27 times) PET bottles (minimal Sb leaching from PC bottles, <15 ng L(-1)) did not pose a serious risk to human health according to current daily Sb acceptable intake estimates. Leached Br concentrations from both PET and PC containers (up to ∼15 μg L(-1)) did not pose a consumer health risk either, however, no acceptable daily dose estimates exist for oral ingestion of organo-brominated, or other plasticizers/additives compounds if they were to be found in bottled water at much lower concentrations. Additional research on potential leaching of organic chemicals from water packaging materials is deemed necessary under relevant environmental conditions.

Determination of per- and polyfluorinated substances in airborne particulate matter by microwave-assisted extraction and liquid chromatography-tandem mass spectrometry

A sensitive and confirmatory analytical method has been developed for the determination of 12 ionic per- and polyfluorinated alkyl substances (PFAS) in fine airborne particulate matter (PM2.5) at trace levels. The proposed method includes extraction of PM2.5-bound PFAS by microwave-assisted extraction (MAE) followed by centrifugation and injection into the liquid chromatograph coupled to a triple quadrupole tandem mass spectrometry system (LC-MS/MS). The main parameters affecting the performance of MAE were optimised using statistical design of experiments (DoE). Recoveries ranged from 83 to 120% and the method quantification limit (MQL) was 1.4 pg m(-3), when air volumes of 720 m(3) were sampled. This method was successfully applied to 41 samples collected from five stations of the monitoring network of the Valencian Regional Government (Spain) during April-July 2010. Eight out of 12 PFCs investigated were quantified in at least one sample (PFBA, PFPeA, PFHxS, 6:2 FTS, PFOA, PFNA, PFOS and PFDA). The measured concentrations ranged from 1.4 to 34.3 pg m(-3).

Application of mass spectrometry in the analysis of polybrominated diphenyl ethers

This review summarized the applications of mass spectrometric techniques for the analysis of the important flame retardants polybrominated diphenyl ethers (PBDEs) to understand the environmental sources, fate and toxicity of PBDEs that were briefly discussed to give a general idea for the need of analytical methodologies. Specific performance of various mass spectrometers hyphenated with, for example, gas chromatograph, liquid chromatograph, and inductively coupled plasma (GC/MS, LC/MS, and ICP/MS, respectively) for the analysis of PBDEs was compared with an objective to present the information on the evolution of MS techniques for determining PBDEs in environmental and human samples. GC/electron capture negative ionization quadrupole MS (GC/NCI qMS), GC/high resolution MS (GC/HRMS) and GC ion trap MS (GC/ITMS) are most commonly used MS techniques for the determination of PBDEs. New analytical technologies such as fast tandem GC/MS and LC/MS become available to improve analyses of higher PBDEs. The development and application of the tandem MS techniques have helped to understand environmental fate and transformations of PBDEs of which abiotic and biotic degradation of decaBDE is thought to be one major source of Br(1-9)BDEs present in the environment in addition to direct loading from commercial mixtures. MS-based proteomics will offer an insight into the molecular mechanisms of toxicity and potential developmental and neurotoxicity of PBDEs.

Polybrominated diphenyl ethers (PBDEs) in Mediterranean mussels (Mytilus galloprovincialis) from selected Apulia coastal sites evaluated by GC-HRMS

Samples of Mytilus galloprovincialis were examined to investigate the levels of polybrominated diphenyl ethers (PBDEs) in the Apulia's marine environment, a region in the South of Italy. The levels of nine PBDE congeners were measured in 40 mussel samples taken from the aquaculture farms in the South of Adriatic Sea and North Ionian Sea along the Apulia coast. While accelerated solvent extraction (ASE) was the extraction technique adopted using acetone/n-hexane (1:1, v/v), the content of PBDEs was evaluated by using gas chromatography coupled with high-resolution mass spectrometry (GC-HRMS) via electron ionization (EI) in the multiple ion monitoring (MIM) mode (two ions for each compound). The (13)C mass-labeled compounds were used to establish the levels of PBDEs in M. galloprovincialis samples. The total concentration of PBDEs (ΣPBDEs) ranged from 0.2 to 6.9 ng/g dry mass, with the highest concentrations found around coastal areas of Salento. With regard to the composition of PBDE congeners, BDE-47, BDE-99 and BDE-100 were the predominant congeners in most of the samples. The present study is the first to report levels of PBDEs occurring in aquatic organisms living in aquaculture farms of Apulia region.

Hydrogen-rich fuel gas from rice straw via microwave-induced pyrolysis

This study aimed to research the productivity of H(2)-rich fuel gas from rice straw using the microwave-induced pyrolysis. The formation constituents of gas product and the mechanism of its production were also discussed. The primary components of gas product were H(2), CO(2), CO, and CH(4), with average percentages of 50.67, 22.56, 16.09, and 7.42vol.%, respectively. According to the TA-MS analysis, it was suggested that focused heating by microwaves made the microwave-induced pyrolysis different from the traditional pyrolysis. A chemical equation could be nearly balanced to illustrate the gas composition generated from rice straw. From the viewpoint of energy consumption, close to 60% of the input energy could be derived and utilized as bioenergy.

Design-of-experiment optimization of exhaled breath condensate analysis using a miniature differential mobility spectrometer (DMS)

Analytical instruments that can measure small amounts of chemicals in complicated biological samples are often useful as diagnostic tools. However, it can be challenging to optimize these sensors using actual clinical samples, given the heterogeneous background and composition of the test materials. Here we use gas chromatography-differential mobility spectrometry (GC/DMS) to analyze the chemical content of human exhaled breath condensate (EBC). Ultimately, this system can be used for non-invasive disease diagnostics. Many parameters can be adjusted within this instrument system, and we implemented a factorial design-of-experiments to systematically test several combinations of parameter settings while concurrently analyzing effects and interactions. We examined four parameters that affect sensitivity and detection for our instrument, requiring a 2(4) factorial design. We optimized sensor function using EBC samples spiked with acetone, a known clinical biomarker in breath. Two outputs were recorded for each experiment combination: number of chemicals detected, and the amplitude of acetone signal. Our goal is to find the best parameter combination that yields the highest acetone peak while also preserving the largest number of other chemical peaks in the spectra. By optimizing the system, we can conduct further clinical experiments with our sensor more efficiently and accurately.

Optimization of large-volume injection for the determination of polychlorinated biphenyls in children's fast-food menus by low-resolution mass spectrometry

This study includes the determination of five indicator polychlorinated biphenyls (PCBs) (52, 101, 153, 138, and 180), six non-ortho PCBs (35, 80, 81, 77, 126, and 169), and two mono-ortho PCBs (28 and 118) in fast food for children. A freeze-dried sample of 10 g is extracted by using pressurized n-hexane in two 5 min cycles at 120 degrees C and 100 mbar. Fatty extracts were cleaned up by means of acetonitrile/n-hexane partitioning and gel-permeation chromatography. The fractionation of non-ortho, mono-ortho, and indicator PCBs was made on graphitized carbon solid-phase extraction cartridges by using n-hexane, n-hexane/toluene (99:1, v/v), and toluene as elution solvents. Gas chromatography coupled to tandem mass spectrometry and large-volume injections with a programmed-temperature vaporizer (PTV-LV) were used to increase sensitivity and selectivity of the PCB determination. The PTV-LV injection settings, that is, vaporizing temperature, vaporizing time, and purge flow, were optimized by using a central composite design. A 15-40 times increased sensitivity was reached as compared with that obtained with the conventional 1 microL splitless injection. The limits of detection achieved were between 0.3 and 1.2 pg/g, and repeatability data, as relative standard deviation varied, ranged from 2 to 9% for the 0.05 ng/mL PCB level.

Occurrence of polychlorinated naphthalenes, polychlorinated biphenyls and short-chain chlorinated paraffins in marine sediments from Barcelona (Spain)

Polychlorinated naphthalenes (PCNs), short-chain chlorinated paraffins (SCCPs) and polychlorinated biphenyls (PCBs) were analysed in marine sediment samples collected from the coastal area of Barcelona (Spain) and near of a submarine emissary coming from a waste water treatment plant located at the mouth of the Besòs River (Barcelona). An integrated sample treatment based on Soxhlet extraction followed by a simple clean-up with Florisil and graphitized carbon cartridge was employed. Gas chromatography coupled to ion-trap tandem mass spectrometry (GC-MS/MS) and gas chromatography-mass spectrometry in electron capture negative ionization mode, were used for PCN and SCCP determinations, respectively, while for PCB analysis gas chromatography with electron capture detection (GC-ECD) was used. The method developed provided low limits of detection (0.001-0.003 ng g(-1) dry weight (dw) for PCNs, 1.8 ng g(-1) for SCCPs and 0.006-0.014 ng g(-1)dw for PCBs) and good run-to-run precisions (lower than RSD 8%) for the analysis of sediment samples. Concentration levels ranging from 0.17 to 3.27 ng g(-1)dw for PCNs, between 0.21 and 1.17 microg g(-1)dw for SCCPs, and from 2.33 to 44.00 ng g(-1) (dw) for PCBs, were found in the coastal sediments, while for samples collected near to the submarine emissary higher levels (from 2.02 to 6.56 ng g(-1)dw for PCNs, between 1.25 and 2.09 microg g(-1)dw for SCCPs and from 22.34 to 37.74 ng g(-1)dw for PCBs) were obtained. The results obtained provide new data about the occurrence of PCN and SCCP in the coastal area of Barcelona.

Simultaneous use of gas chromatography/ion trap mass spectrometry - electron capture detection to improve the analysis of bromodiphenyl ethers in biological and environmental samples

Bromodiphenyl ethers (BDEs) are a class of synthetic flame retardants and are widely present in the environment. Analysis of higher BDE congeners has proven to be a challenge. We report the development of a method that enhances their analysis by splitting the eluent of a gas chromatograph (GC) between an electron capture detector (ECD) and an ion trap mass spectrometer (ITMS): 1:10, ECD:ITMS. This allowed the quantitation of the lower molecular weight (MW) BDE congeners (Br1-Br7) with the ITMS and of the higher MW BDEs (Br8-Br10) with the highly sensitive ECD. The IT temperature, ionization mode, and MS/MS parameters (excitation amplitude and stability parameter) were optimized. This method took the advantages of the best detector for the different BDE homologues and was suitable for the analysis of BDEs in environmental and biological samples. Average recoveries were 52-112% for BDEs from spiked sand samples and 57-126% from spiked lard samples after accelerated solvent extraction followed by silica gel and alumina column clean-up. Average recoveries ranged from 51% to 130% for 13C-labeled BDEs spiked in the real and in matrix samples. The method detection limits for specific congeners were 0.18-120 pg/g of the BDEs in animal tissue samples, and 0.05-40 pg/g in soil and indoor dust samples. The utility of the method was demonstrated by analyzing actual harbor seal blubber, indoor dust and soil samples. The concentration of each BDE ranged from non-detectable (nd) to 41 ng/g in the dry soil sample, nd to 1042 ng/g in the indoor dust, nd to 15 ng/g wet weight in the Alaskan harbor seal blubber sample, and 0.02 to 11 ng/microL of the identified 23 of the 42 breakdown products from BDE-209 after zerovalent iron treatment. Finally, an interlaboratory comparison showed high correspondence between the GC/ITMS-ECD method and a GC high-resolution MS system for the analysis of BDEs in soil samples.

Analysis of PBDEs in soil, dust, spiked lake water, and human serum samples by hollow fiber-liquid phase microextraction combined with GC-ICP-MS

A novel method for the analysis of four polybrominated diphenyl ethers (PBDEs) in environmental and human serum samples based on hollow fiber-liquid phase microextraction (HF-LPME) followed by gas chromatography-inductively coupled plasma mass spectrometric (GC-ICP-MS) detection has been developed. The organic solvent in the porous hollow fiber was first dipped into the sample for extraction at a given time, and the retracted organic phase was introduced into the GC-ICP-MS for analysis. The addition of methanol has a strong effect on the HF-LPME extraction efficiency. Other significant parameters affecting the extraction efficiency of HF-LPME were also studied. HF-LPME was effective to isolate the analytes from the complex matrix. Under the optimized conditions, the detection limits of the proposed method varied from 15.2 to 40.5 ng/L. In general, the relative standard deviations (RSDs) were less than 10%. Good linearity was obtained with the correlation coefficients all better than 0.999. The proposed method is simple, quick, few microliters of organic solvent required, and is especially suitable for the analysis of the real sample with small amount available. The overall process of HF-LPME with GC-ICP-MS was applied successfully for the determination of polybrominated diphenyl ethers (PBDEs) in environmental and spiked human serum samples, and the results were satisfactory.

Recent developments in the analysis of brominated flame retardants and brominated natural compounds

This article reviews recent literature on the analysis of brominated flame retardants (BFRs) and brominated natural compounds (BNCs). The main literature sources are reviews from the last five years and research articles reporting new analytical developments published between 2003 and 2006. Sample pretreatment, extraction, clean-up and fractionation, injection techniques, chromatographic separation, detection methods, quality control and method validation are discussed. Only few new techniques, such as solid-phase microextraction (SPME) or pressurized liquid extraction (PLE), have been investigated for their ability of combining the extraction and clean-up steps. With respect to the separation of BFRs, the most important developments were the use of comprehensive two-dimensional gas chromatography for polybrominated diphenyl ethers (PBDEs) and the growing tendency for liquid-chromatographic techniques for hexabromocyclododecane (HBCD) stereoisomers and of tetrabromobisphenol-A (TBBP-A). At the detection stage, mass spectrometry (MS) has been developed as well-established and reliable technology in the identification and quantification of BFRs. A growing attention has been paid to quality assurance. Interlaboratory exercises directed towards BFRs have grown in popularity and have enabled laboratories to validate analytical methods and to guarantee the quality of their results. The analytical procedures used for the identification and characterization of several classes of BNCs, such as methoxylated polybrominated diphenyl ethers (MeO-PBDEs) (also metabolites of PBDEs), halogenated methyl or dimethyl bipyrroles (DBPs), are reviewed here for the first time. These compounds were generally identified during the routine analysis of BFRs and have received little attention until recently. For each topic, an overview is presented of its current status.

Applications of microwave-assisted processes (MAP™) to environmental analysis

The use of microwave-assisted extraction has gained wide acceptance as a powerful tool for the recovery of environmental contaminants and their subsequent analysis. This paper reviews the historical and fundamental basis of the technology. It also provides a cursory review of the current state-of-the-art and literature (2000-2006) in the area of environmental analysis in addition to providing a critical review of the level of efforts being devoted to its further development.

Pressurized liquid extraction in environmental analysis

A critical evaluation of recent literature utilizing pressurized liquid extraction (PLE) for environmental analysis is presented by compound class. Overall, the extraction efficiency of PLE, using the appropriate solvent, temperature and pressure for extraction, is similar to that of Soxhlet extraction. PLE has been used for some classes of compounds that are thermally labile (e.g., explosives) and may require acidic conditions for extraction (e.g., organometallic compounds). References to recent applications are presented emphasizing studies which utilize unspiked, natural matrices and studies that compare PLE to alternate extraction techniques.

Microwave-assisted solvent extraction and gas chromatography ion trap mass spectrometry procedure for the determination of persistent organochlorine pesticides (POPs) in marine sediment

Microwave-assisted solvent extraction of persistent organochlorine pesticides (POPs) in marine sediment was developed and optimized by means of two-level factorial designs. Six variables (microwave power, extraction time and temperature, amount of sample, solvent volume, and sample moisture) were considered as factors in the optimization process. The results show that the amount of sample to be extracted and solvent volume are statistically significant for the overall recovery of the studied pesticides, although compromise conditions have to be established with the object of avoiding overpressure in closed vessels. After extraction, a clean up step including the use of a silica cartridge was performed prior to chromatographic determination in order to remove interferences. The optimized procedure was compared to conventional Soxhlet extraction. The MS-MS ion preparation mode was applied to improve the sensitivity and selectivity of the chromatographic technique.