In-situ ionic liquid dispersive liquid-liquid microextraction using a new anion-exchange reagent combined Fe 3 O 4 magnetic nanoparticles for determination of pyrethroid pesticides in water samples

Preparation of an imidazolium-based poly(ionic liquid) functionalized magnetic three-dimensional graphene oxide for magnetic solid phase extraction of pyrethroids from tea samples

In this work, an imidazolium-based poly(ionic liquid) (poly(1-dodecyl-3-vinyl-imidazolium bromide) functionalized magnetic three-dimensional graphene oxide (Fe3O4@3D-GO@poly(ImC12+Br-)) was synthesized via a vacuum freezing-drying method and used as a magnetic solid phase extraction (MSPE) adsorbent for the efficient extraction of pyrethroid pesticides from tea samples. The prepared Fe3O4@3D-GO@poly(ImC12+Br-) was confirmed by scanning electron microscopy (SEM), Fourier transform infrared spectrometry (FT-IR), vibrating sample magnetometer (VSM) and X-ray photoelectron spectrogram (XPS). Due to its large specific surface area and the ability to offer multiple intermolecular interactions, including π-π stacking, hydrophobic and hydrogen bond interactions, the prepared Fe3O4@3D-GO@poly(ImC12+Br-) showed high extraction efficiency for pyrethroids. The experimental parameters were optimized by a combination of single-factor method and Box-Behnken design to improve the extraction efficiency. Under the optimum conditions, coupled with high performance liquid chromatography (HPLC), a sensitive analytical method was developed for the determination of pyrethroids, and the proposed method showed wide linear ranges (1.00-100 μg L-1) with correlation coefficients (R) ranging from 0.9980 to 0.9994, low limits of detection (0.100 μg L-1) and good repeatability with intra-day relative standard deviations (RSDs) in the range of 2.90-5.53 % and inter-day RSDs in the range of 1.83-7.76 %. Moreover, the developed method was successfully applied to the determination of pyrethroids in tea samples and satisfactory recoveries ranging from 82.37 % to 114.34 % were obtained. The results showed that the developed Fe3O4@3D-GO@poly(ImC12+Br-) was an ideal, effective and selective material for the extraction and enrichment of pyrethroids from tea samples.

In situ formation of solidified supramolecular solvent based dispersive liquid-liquid microextraction for the enrichment of phenylurea herbicides in water, fruit juice, and milk

A convenient, efficient, and green dispersive liquid-liquid microextraction based on the in situ formation of solidified supramolecular solvents combined with high performance liquid chromatography was developed for the determination of four phenylurea herbicides in liquid samples, including monuron, monolinuron, isoproturon, and chlortoluron. Herein, a novel supramolecular solvent was prepared by the in situ reaction of [P4448]Br and NH4PF6, which had the advantages of low melting point, high density, and good dispersibility. In addition, the microscopic morphology and physical properties of supramolecular solvent were characterized, and the extraction conditions were optimized. The results showed that the analytes had good linearity (R2 > 0.9998) within the linear range. The limits of detection and quantification for the four phenylurea herbicides were in the range of 0.13-0.19 μg L-1 and 0.45-0.65 μg L-1, respectively. The prepared supramolecular solvent is suitable for the efficient extraction of phenylurea herbicides in water, fruit juice, and milk.

Nanomaterials and biochar mediated remediation of emerging contaminants

The unrestricted release of various toxic substances into the environment is a critical global issue, gaining increased attention in modern society. Many of these substances are pristine to various environmental compartments known as contaminants/emerging contaminants (ECs). Nanoparticles and emerging sorbents enhanced remediation is a compelling methodology exhibiting great potential in addressing EC-related issues and facilitating their elimination from the environment, particularly those compounds that demonstrate eco-toxicity and pose considerable challenges in terms of removal. It provides a novel technique enabling the secure and sustainable removal of various ECs, including persistent organic compounds, microplastics, phthalate, etc. This extensive review presents a critical perspective on the current advancements and potential outcomes of nano-enhanced remediation techniques such as photocatalysis, nano-sensing, nano-enhanced sorbents, bio/phyto-remediation, which are applied to clean-up the natural environment. In addition, when dealing with residual contaminants, special attention is paid to both health and environmental implications; therefore, an evaluation of the long-term sustainability of nano-enhanced remediation methods has been considered. The integrated mechanical approaches were thoroughly discussed and presented in graphical forms. Thus, the critical evaluation of the integrated use of most emerging remediation technologies will open a new dimension in environmental safety and clean-up program.

Application of Recently used Green Solvents in Sample Preparation Techniques: A Comprehensive Review of Existing Trends, Challenges, and Future Opportunities

Green solvents (GSs) has gained significant attention in recent years due to their potential as safer and more sustainable alternatives to traditional organic solvents. Solvents are used in a wide range of applications, from industrial processes to everyday products. Solvent emissions and losses can have a significant impact on the environment and human health, which is why many initiatives are being undertaken to get rid of or switch to eco-friendly alternatives. A key area of green chemistry that led to the concept of "green" solvents is the development of alternative solvents that are less toxic and more environmentally friendly than traditional organic solvents. The advantages of using green solvents over conventional ones are their environmental friendliness, biocompatibility, biodegradability, and simplicity of preparation. Different sample preparation techniques have successfully utilized green solvents to offer a sustainable separation media for the extraction of a variety of inorganic and organic compounds which are crucial for research in environmental samples. Recent developments in green analytical chemistry (GAC) have focused on how to prepare and use samples using environmentally sustainable solvents. The current study covers the advance and currently used green solvents with an emphasis on environmentally friendly sample preparation methods. This review aims to briefly summarize the current state of knowledge about the use of green solvents particularly ionic liquids, deep eutectic solvents and switchable solvents (SSs) with the perspective of GAC in sample preparation methods.

Ionic Liquid-Assisted DLLME and SPME for the Determination of Contaminants in Food Samples

Developing effective and green methods for food analysis and separation has become an urgent issue regarding the ever-increasing concern of food quality and safety. Ionic liquids (ILs) are a new chemical medium and soft functional material developed under the framework of green chemistry and possess many unique properties, such as low melting points, low-to-negligible vapor pressures, excellent solubility, structural designability and high thermal stability. Combining ILs with extraction techniques not only takes advantage of ILs but also overcomes the disadvantages of traditional extraction methods. This subject has attracted intensive research efforts recently. Here, we present a brief review of the current research status and latest developments regarding the application of IL-assisted microextraction, including dispersive liquid–liquid microextraction (DLLME) and solid-phase microextraction (SPME), in food analysis and separation. The practical applications of ILs in determining toxic and harmful substances in food specimens with quite different natures are summarized and discussed. The critical function of ILs and the advantages of IL-based microextraction techniques over conventional extraction techniques are discussed in detail. Additionally, the recovery of ILs using different approaches is also presented to comply with green analytical chemistry requirements.

[Application progress of covalent organic framework materials in extraction of toxic and harmful substances]

Toxic and hazardous substances constitute a category of compounds that are potentially hazardous to humans, other organisms, and the environment. These substances include pesticides (benzoylureas, pyrethroids, neonicotinoids), persistent organic pollutants (polycyclic aromatic hydrocarbons, polychlorinated biphenyls, perfluorinated compounds), plasticizers (phthalate esters, phenolic endocrine disruptors), medicines (sulfonamides, non-steroid anti-inflammatory drugs, tetracyclines, fluoroquinone antibiotics), heterocyclic aromatic amines, algal toxins, and radioactive substances. Discharge of these toxic and harmful substances, as well as their possible persistence and bioaccumulation, pose a major risk to human health, often to the extent of being life-threatening. Therefore, it is important to analyze and detect toxic and hazardous substances in the environment, drinking water, food, and daily commodities. Sample pretreatment is an imperative step in most of the currently used analytical methods, especially in the analysis of trace toxic and harmful substances in complex samples. An efficient and fast sample pretreatment technology not only helps improve the sensitivity, selectivity, reproducibility, and accuracy of analytical methods, but also avoids contamination of the analytical instruments and even damages the performance and working life of instruments. Sample pretreatment techniques widely used in the extraction of toxic and hazardous substances include solid-phase extraction (SPE), solid-phase microextraction (SPME), and dispersed solid-phase extraction (DSPE). The adsorbent material plays a key role in these pretreatment techniques, thereby determining their selectivity and efficiency. In recent years, covalent organic frameworks (COFs) have attracted increasing attention in sample pretreatment. COFs represent an exciting new class of porous crystalline materials constructed via the strong covalent bonding of organic building units through a reversible condensation reaction. COFs present four advantages: (1) precise control over structure type and pore size by consideration of the target molecular structure based on the connectivity and shape of the building units; (2) post-synthetic modification for chemical optimization of the pore interior toward optimized interaction with the target; (3) straightforward scalable synthesis; (4) feasible formation of composites with magnetic nanoparticles, carbon nanotubes, graphene, silica, etc., which is beneficial to enhance the performance of COFs and meet the requirement of diverse pretreatment technologies. Because of the well-defined crystalline porous structures and tailored functionalities, COFs have excellent potential for use in target extraction. However, some issues need to be addressed for the application of COFs in the extraction of toxic and hazardous substances. (1) For the sample matrix, most of the reported COFs are highly hydrophobic, which limits their dispersibility in water-based samples, leading to poor extraction performance. COFs with good dispersibility in water-based samples are urgently required. (2) Besides, COFs rely on hydrophobic interaction, size repulsion, π-π stacking, and Van der Waals forces to extract target substances, but they are not effective for some polar targets. Thus, it is necessary to develop COFs with high affinity for polar toxic and hazardous substances. (3) Methods for the synthesis of COFs have evolved from solvothermal methods to room-temperature methods, mechanical grinding, microwave-assisted synthesis, ion thermal methods, etc. Most of the existing methods are time-consuming, laborious, and environmentally unfriendly. The starting materials are too expensive to prepare COFs in large quantities. More effort is required to improve the synthesis efficiency and overcome the obstacles in the application of COFs for extraction. This article summarizes and reviews the research progress in COFs toward the extraction of toxic and hazardous substances in recent years. Finally, the application prospects of COFs in this field are summarized, which serves as a reference for further research into pretreatment technologies based on COFs.

Magnetic solid-phase extraction of pyrethroid and neonicotinoid insecticides separately in environmental water samples based on alkaline or acidic group-functionalized mesoporous silica

In this work, amino- or carboxyl-functionalized magnetic KIT-6 have been synthesized separately. The two nanocomposites were successfully used to enrich pyrethroids and neonicotinoids insecticides from environmental water samples, respectively.

Micro-gel thin film molecularly imprinted polymer coating for extraction of organophosphorus pesticides from water and beverage samples

Molecularly imprinted polymers (MIPs) have become an important class of materials for selective and efficient adsorption of target analytes. Despite versatility of MIPs for fabrication in numerous formats, these materials have been primarily reported as solid phase extraction packing materials. An effective thin film MIP prepared on stainless steel substrate is reported here for high throughput enrichment of organophosphorus pesticides (OPPs) from water and beverage samples followed by liquid chromatography tandem mass spectrometry (LC-MS/MS) analysis. The key factors controlling performance as well as best practices for optimized fabrication of thin film MIPs are presented. A pseudo-phase diagram is introduced to evaluate and predict the effect of the ratio of porogen (solvent, 1-octanol) volume to relative crosslinker mass on the desired polymer features (i.e., porosity, surface area, capacity, and selectivity). At low porogen ratios, a macroporous polymer with insignificant selectivity is formed, whereas at high porogen ratios a micro-gel polymer with superior selectivity towards targets is obtained. The porosity and morphology determined with nitrogen adsorption and scanning electron microscopy were attributed to specific regions in the pseudo-phase diagram. Other factors influencing selectivity and stability of the polymer, such as type of the template and its ratios with monomer (methacrylic acid) and crosslinker (ethylene glycol dimethacrylate) were optimized. The prepared thin film MIPs were characterized using adsorption isotherms and adsorption kinetics, and evaluated for matrix effects (high humic acid content) and cross-reactivity in presence of other pesticides and pharmaceuticals. The optimized method provided limits of quantitation (LOQs) ranged from 0.002 to 0.02 ng mL^-1 in water and from 0.095 to 0.48 ng g^-1 in apple juice. Regarding inter-device variability (CV∼10% without normalization), excellent linearity (R² > 0.99), satisfactory accuracies (90-110%) and precisions (<15%) were obtained.

Strategies of dispersive liquid-liquid microextraction for coastal zone environmental pollutant determination

Coastal zone means the interface of land and sea, and therefore, environmental pollutants steaming from land-based activities (like manufactories) and sea-based activities (like shipping) are all existing in coastal zone. These pollutants usually have characteristics of low residues, complicated matrices, easy accumulation and so on, causing difficulty to detect coastal pollutants quickly and sensitively. It is imperative to perform effective sample preparation prior to instrumental analysis. Dispersive liquid-liquid microextraction (DLLME) has attracted significant research interest for sample preparation, owing to its high enrichment ability, low reagent/sample consumption, and wide analyte/matrix applicability, as well as robustness, simplicity, rapidity and inexpensiveness. Herein, we comprehensively review the recent advancements of DLLME technology and its analytical parameters including enrichment principles, extraction modes, and practical application; the emphasis is on novel mode-construction and representative coastal-environmental pollutants extraction. Construction strategies are highlighted by classifying DLLME into five major modes, according to extractant's types, including normal ones, low density solvents, ionic liquids, deep eutectic solvents and others. The coupling of DLLME with other extraction techniques like solid-phase extraction is also briefly introduced. The strengths and weaknesses of each strategy and its rationality are also elaborated. In addition, some typical applications of the different DLLME modes for the determination of organic compounds and heavy metals in coastal water, sediment, soil, and biota are summarized. The increasingly concerned green aspects and instrumentation of DLLME are presented, and finally, the challenges and perspectives of the DLLME for environmental analysis are proposed.

Role of Ionic Liquids in Composites in Analytical Sample Preparation

Ionic liquids (ILs) are a group of non-conventional salts with melting points below 100 °C. Apart from their negligible vapor pressure at room temperature, high thermal stability, and impressive solvation properties, ILs are characterized by their tunability. Given such nearly infinite combinations of cations and anions, and the easy modification of their structures, ILs with specific properties can be synthesized. These characteristics have attracted attention regarding their use as extraction phases in analytical sample preparation methods, particularly in liquid-phase extraction methods. Given the liquid nature of most common ILs, their incorporation in analytical sample preparation methods using solid sorbents requires the preparation of solid derivatives, such as polymeric ILs, or the combination of ILs with other materials to prepare solid IL-based composites. In this sense, many solid composites based on ILs have been prepared with improved features, including magnetic particles, carbonaceous materials, polymers, silica materials, and metal-organic frameworks, as additional materials forming the composites. This review aims to give an overview on the preparation and applications of IL-based composites in analytical sample preparation in the period 2017–2020, paying attention to the role of the IL material in those composites to understand the effect of the individual components in the sorbent.

Development, validation, comparison, and implementation of a highly efficient and effective method using magnetic solid-phase extraction with hydrophilic-lipophilic-balanced materials for LC-MS/MS analysis of pesticides in seawater

To achieve multi-pesticides residue analysis in seawater, hydrophilic-lipophilic-balanced magnetic particles were designed and fabricated by swelling polymerization of divinyl benzene (DVB) and N-vinyl pyrrolidone (NVP) on the surface of Fe₃O₄@SiO₂ magnetic particles. The ratio of DVB to NVP was adjusted to achieve a proper balance in hydrophilicity and lipophilicity. The obtained magnetic particles were systematically characterized by TEM, SEM, FT-IR and vibrating sample magnetization. Based on the optimized magnetic nanoparticles, a sensitive magnetic solid-phase extraction method was developed for the simultaneous pre-concentration and determination of 96-pesticide residues from large-volume seawater samples prior to being detected by liquid chromatography-tandem mass spectrometry. Recoveries of pesticides in spiked seawater samples (0.001, 0.01, 0.1, 1.0 μg L^-1) ranged from 62% to 112% with RSDs less than 21%. The method limits of detection of 96 pesticides ranged from 0.13 to 0.42 ng L^-1, the method limits of quantification of 96 pesticides ranged from 1.0 to 10 ng L^-1. The method was successfully applied to pesticide residue analysis in water samples from Jiulong River Estuary of China, demonstrating the prospects of this technique as a potential method for the rapid determination of trace levels of multi-pesticide residues in seawater.

Lauric Acid-Modified Nitraria Seed Meal Composite as Green Carrier Material for Pesticide Controlled Release

To alleviate the adverse effects of pesticide residues on the environment, development of a more safe, economical, and reliable usage approach of pesticides is critically urgent. In the present study, a novel pesticide carrier LA-NSM (lauric acid-modified Nitraria seed meal) with controlled release property was prepared through grafting esterification of lauric acid onto Nitraria seed meal substrates. The structure of the obtained samples was characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy, and contact angle measurements. The results indicated that LA-NSM products had a well-defined hydrophobic surface and irregular holes for efficient loading of pesticide molecules. Deltamethrin (DEL), a representative insoluble pyrethroid insecticide in water, was deliberately selected as the index pesticide to evaluate the loading and releasing efficiency of LA-NSM. The loading capacity of LA-NSM for DEL can reach about 1068 mg/g. pH, humidity of soil, and temperature had a significant influence on controlled release performance of LA-NSM@DEL. Moreover, the releasing kinetics of LA-NSM@DEL composites could be fitted well with the Higuchi model. Overall, the highly hydrophobic property, excellent loading, and controlled release ability of LA-NSM made it a promising candidate in agricultural applications.

Relationship between the Structure of Ionic Liquid and Its Enrichment Ability To Trace Fungicides from an Environmental Water Sample

To elucidate the relationship between the structure of ionic liquid (IL) and its enrichment ability to trace pesticides from an environmental water sample, a series of imidazole-based ILs were synthesized to extract four fungicides (boscalid, cyprodinil, fluazinam, and pyrimethanil) through an in situ ionic liquid dispersive liquid-liquid microextraction method. The results showed that aromatic heterocyclic monocation ionic liquids (MILs) had better extraction ability to fungicides than other three alicyclic heterocyclic MILs. Dication ionic liquids (DILs) with the four carbons at the side chain had better ability to extract fungicides than MILs, and DILs with a long bridge carbon chain had better recoveries of fungicides with low K_ow values. The proposed method showed high mean enrichment factors and high recoveries of the fungicides from real water samples. The rules of the relationship between the structure of IL and enrichment ability are instructive to the application of ILs in pretreatment of complex substances.

Three-dimensional hollow porous raspberry-like hierarchical Co/Ni@carbon microspheres for magnetic solid-phase extraction of pyrethroids

A three-dimensional magnetic hollow porous raspberry-like hierarchical Co/Ni@carbon microspheres (3D Co/Ni@carbon) were synthesized by using a bimetal-organic framework (Co/Ni-MOF) as a precursor and subsequent calcination under nitrogen. The 3D Co/Ni@carbon is a novel solid phase extractant that displays outstanding extraction capability and separation efficiency for the pyrethroid pesticides ethofenprox and bifenthrin. This is ascribed to the beneficial effects of facile analyte transport (due to the presence of free pores), the abundant number of adsorption sites (which warrant efficient extraction), and the excellent structural stability of the material. The 3D Co/Ni@carbon was applied to dispersive magnetic solid-phase extraction (d-MSPE), and the two pyrethroids were quantified by HPLC (UV detection wavelength: 220 nm). The method has a high preconcentration factor (937-1012) and give recoveries that range between 85.6-106.9%, with RSDs (for n = 5) of <6% in case of real samples. Graphical abstract The hierarchical porous Co/Ni@carbon microsphere as adsorbent was fabricated, and it showed high extraction efficiency for two pyrethroids.

Nanotechnology-based recent approaches for sensing and remediation of pesticides

Pesticides are meant to control and destroy the pests and weeds. They are classified into different categories on the basis their origin and type of pest they target. Chemical pesticides such as insecticides, herbicides and fungicides are commonly used in agricultural fields. However, the excessive use of these agrochemicals have adverse effects on environment such as reduced population of insect pollinators, threat to endangered species and habitat of birds. Upon consumption; chemical pesticides also cause various health issues such as skin, eye and nervous system related problems and cancer upon prolonged exposure. Various techniques in the past have been developed on the basis of surface adsorption, membrane filtration and biological degradation to reduce the content of pesticides. However, slow response, less specificity and sensitivity are some of the drawbacks of such techniques. In recent times, Nanotechnology has emerged as a helping tool for the sensing and remediation of pesticides. This review focuses on the use of this technology for the detection, degradation and removal of pesticides. Nanomaterials have been classified into nanoparticles, nanotubes and nanocomposites that are commonly used for detection, degradation and removal of pesticides. The review also focuses on the chemistry behind the sensing and remediation of pesticides using nanomaterials. Different types of nanoparticles, viz. metal nanoparticles, bimetallic nanoparticles and metal oxide nanoparticles; nanotubes such as carbon nanotubes and halloysite nanotubes have been used for the detection, degradation and removal of pesticides. Further, various enzyme-based biosensors for detection of pesticides have also been summarized.