A review on fabricating tissue scaffolds using vat photopolymerization

Using Three-Dimensional Bioprinting to Generate Realistic Models of Wound Healing

Significance: The skin serves as the primary defense against external stimuli, making it vulnerable to damage. Injuries can cause a dysregulated environment, resulting in chronic inflammation and inhibition of cell proliferation and migration, which delays recovery. Innovative approaches, such as three-dimensional (3D) bioprinting, can foster a controlled healing environment by promoting synergy between the skin microbiome and cells. Recent Advances: Traditional approaches to wound healing have focused on fostering an environment conducive to the interplay between cells, extracellular proteins, and growth factors. 3D bioprinting, a manufacturing technology with applications in tissue engineering, deposits biomaterial-based bioink containing living cells to fabricate custom-designed tissue scaffolds in a layer-by-layer fashion. This process controls the architecture and composition of a construct, producing multilayered and complex structures such as skin. Critical Issues: The selection of biomaterials for scaffolds has been a challenge when 3D skin tissue engineering. While prioritizing mechanical properties, current biomaterials often lack the ability to interact with environmental stimuli such as pH, temperature, or oxygen levels. Employing smart biomaterials that integrate bioactive molecules and adapt to external conditions could overcome these limitations. This innovation would enable scaffolds to create a sustainable wound-healing environment, fostering microbiome balance, reducing inflammation, and facilitating cellular recovery and tissue restoration, addressing critical gaps in existing wound care solutions. Future Directions: Novel bioink formulations for skin injury recovery are focused on improving long-term cell viability, proliferation, vascularization, and immune integration. Efficient recovery of the skin microbiome using bioactive molecules has the potential to create microenriched environments that support the recovery of the skin microbiome and restore immune regulation. This promising direction for future research aims to improve patient outcomes in wound care.

Microneedle-based arrays - Breakthrough strategy for the treatment of bacterial and fungal skin infections

Currently, fungal and bacterial skin infections rank among the most challenging public health problems due to the increasing prevalence of microorganisms and the development of resistance to available drugs. A major issue in treating these infections with conventional topical medications is the poor penetration through the stratum corneum, the outermost layer of the skin. The concept of microneedles seems to be a future-proof approach for delivering drugs directly into deeper tissues. By bypassing the skin barrier, microneedle systems allow therapeutic substances to reach deeper layers more efficiently, significantly improving treatment outcomes. Nonetheless, the primary challenges regarding the effectiveness of microneedles involve selecting the appropriate size and shape, along with polymer composition and fabrication technology, to enable controlled and efficient drug release. This review offers a comprehensive overview of the latest knowledge on microneedle types and manufacturing techniques, highlighting their potential effectiveness in treating bacterial and fungal skin infections. It includes updated statistics on infection prevalence and provides a detailed examination of common bacterial and fungal diseases, focusing on their symptoms, causative species, and treatment methods. Additionally, the review addresses safety considerations, regulatory aspects, and future perspectives for microneedle-based therapeutic systems. It also underscores the importance of industrialization and clinical translation efforts, emphasizing the significant potential of microneedle technology for advancing medical applications.

Biofabrication - Revolutionizing the future of regenerative periodontics

Periodontium is a compartmentalized and highly specialized tissue responsible for tooth stability. Loss of tooth attachment due to periodontitis and trauma is a complex clinical burden affecting a large parcel of the adult and elderly population worldwide, and regenerative strategies to reestablish the native conditions of the periodontium are paramount. Biofabrication of scaffolds, through various techniques and materials, for regenerative periodontics has significantly evolved in the last decades. From the basics of occlusive membranes and graft materials to the complexity of converging 3D printing and Bioprinting using image-based models, biofabrication opens many possibilities for patient-specific scaffolds that recapitulate the anatomical and physiological conditions of periodontal tissues and interfaces. Thus, this review presents fundamental concepts related to the native characteristics of the periodontal tissues, the key to designing personalized strategies, and the latest trends of biofabrication in regenerative periodontics with a critical overview of how these emerging technologies have the potential to shift the one-size-fits-all paradigm.

Characterization and Machine Learning-Driven Property Prediction of a Novel Hybrid Hydrogel Bioink Considering Extrusion-Based 3D Bioprinting

The field of tissue engineering has made significant advancements with extrusion-based bioprinting, which uses shear forces to create intricate tissue structures. However, the success of this method heavily relies on the rheological properties of bioinks. Most bioinks use shear-thinning. While a few component-based efforts have been reported to predict the viscosity of bioinks, the impact of shear rate has been vastly ignored. To address this gap, our research presents predictive models using machine learning (ML) algorithms, including polynomial fit (PF), decision tree (DT), and random forest (RF), to estimate bioink viscosity based on component weights and shear rate. We utilized novel bioinks composed of varying percentages of alginate (2-5.25%), gelatin (2-5.25%), and TEMPO-Nano fibrillated cellulose (0.5-1%) at shear rates from 0.1 to 100 s-1. Our study analyzed 169 rheological measurements using 80% training and 20% validation data. The results, based on the coefficient of determination (R2) and mean absolute error (MAE), showed that the RF algorithm-based model performed best: [(R2, MAE) RF = (0.99, 0.09), (R2, MAE) PF = (0.95, 0.28), (R2, MAE) DT = (0.98, 0.13)]. These predictive models serve as valuable tools for bioink formulation optimization, allowing researchers to determine effective viscosities without extensive experimental trials to accelerate tissue engineering.

3D-Printed Polymeric Biomaterials for Health Applications

3D printing, also known as additive manufacturing, holds immense potential for rapid prototyping and customized production of functional health-related devices. With advancements in polymer chemistry and biomedical engineering, polymeric biomaterials have become integral to 3D-printed biomedical applications. However, there still exists a bottleneck in the compatibility of polymeric biomaterials with different 3D printing methods, as well as intrinsic challenges such as limited printing resolution and rates. Therefore, this review aims to introduce the current state-of-the-art in 3D-printed functional polymeric health-related devices. It begins with an overview of the landscape of 3D printing techniques, followed by an examination of commonly used polymeric biomaterials. Subsequently, examples of 3D-printed biomedical devices are provided and classified into categories such as biosensors, bioactuators, soft robotics, energy storage systems, self-powered devices, and data science in bioplotting. The emphasis is on exploring the current capabilities of 3D printing in manufacturing polymeric biomaterials into desired geometries that facilitate device functionality and studying the reasons for material choice. Finally, an outlook with challenges and possible improvements in the near future is presented, projecting the contribution of general 3D printing and polymeric biomaterials in the field of healthcare.

Bioprinting PDLSC-Laden Collagen Scaffolds for Periodontal Ligament Regeneration

Periodontitis and severe trauma are major causes of damage to the periodontal ligament (PDL). Repairing the native conditions of the PDL is essential for the stability of the tissue and its interfaces. Bioprinting periodontal ligament stem cells (PDLSCs) is an interesting approach to guide the regeneration of PDL and interfacial integration. Herein, a collagen-based bioink mimicking the native extracellular matrix conditions and carrying PDLSCs was tested to guide the periodontal ligament organization. The bioink was tested at two different concentrations (10 and 15 mg/mL) and characterized by swelling and degradation, microstructural organization, and rheological properties. The biological properties were assessed after loading PDLSCs into bioinks for bioprinting. The characterization was performed through cell viability, alizarin red assay, and expression for ALP, COL1A1, RUNX2, and OCN. The in vivo biocompatibility of the PDLSC-laden bioinks was verified using subcutaneous implantation in mice. Later, the ability of the bioprinted PDLSC-laden bioinks on dental root fragments to form PDL was also investigated in vivo in mice for 4 and 10 weeks. The bioinks demonstrated typical shear-thinning behavior, a porous microstructure, and stable swelling and degradation characteristics. Both concentrations were printable and provided suitable conditions for a high cell survival, proliferation, and differentiation. PDLSC-laden bioinks demonstrated biocompatibility in vivo, and the bioprinted scaffolds on the root surface evidenced PDLSC alignment, organization, and PDLSC migration to the root surface. The versatility of collagen-based bioinks provides native ECM conditions for PDLSC proliferation, alignment, organization, and differentiation, with translational applications in bioprinting scaffolds for PDL regeneration.

Recent advances in the 3D skin bioprinting for regenerative medicine: Cells, biomaterials, and methods

The skin is a tissue constantly exposed to the risk of damage, such as cuts, burns, and genetic disorders. The standard treatment is autograft, but it can cause pain to the patient being extremely complex in patients suffering from burns on large body surfaces. Considering that there is a need to develop technologies for the repair of skin tissue like 3D bioprinting. Skin is a tissue that is approximately 1/16 of the total body weight and has three main layers: epidermis, dermis, and hypodermis. Therefore, there are several studies using cells, biomaterials, and bioprinting for skin regeneration. Here, we provide an overview of the structure and function of the epidermis, dermis, and hypodermis, and showed in the recent research in skin regeneration, the main cells used, biomaterials studied that provide initial support for these cells, allowing the growth and formation of the neotissue and general characteristics, advantages and disadvantages of each methodology and the landmarks in recent research in the 3D skin bioprinting.

Light-Responsive and Antibacterial Graphenic Materials as a Holistic Approach to Tissue Engineering

While the continuous development of advanced bioprinting technologies is under fervent study, enhancing the regenerative potential of hydrogel-based constructs using external stimuli for wound dressing has yet to be tackled. Fibroblasts play a significant role in wound healing and tissue implants at different stages, including extracellular matrix production, collagen synthesis, and wound and tissue remodeling. This study explores the synergistic interplay between photothermal activity and nanomaterial-mediated cell proliferation. The use of different graphene-based materials (GBM) in the development of photoactive bioinks is investigated. In particular, we report the creation of a skin-inspired dressing for wound healing and regenerative medicine. Three distinct GBM, namely, graphene oxide (GO), reduced graphene oxide (rGO), and graphene platelets (GP), were rigorously characterized, and their photothermal capabilities were elucidated. Our investigations revealed that rGO exhibited the highest photothermal efficiency and antibacterial properties when irradiated, even at a concentration as low as 0.05 mg/mL, without compromising human fibroblast viability. Alginate-based bioinks alongside human fibroblasts were employed for the bioprinting with rGO. The scaffold did not affect the survival of fibroblasts for 3 days after bioprinting, as cell viability was not affected. Remarkably, the inclusion of rGO did not compromise the printability of the hydrogel, ensuring the successful fabrication of complex constructs. Furthermore, the presence of rGO in the final scaffold continued to provide the benefits of photothermal antimicrobial therapy without detrimentally affecting fibroblast growth. This outcome underscores the potential of rGO-enhanced hydrogels in tissue engineering and regenerative medicine applications. Our findings hold promise for developing game-changer strategies in 4D bioprinting to create smart and functional tissue constructs with high fibroblast proliferation and promising therapeutic capabilities in drug delivery and bactericidal skin-inspired dressings.

Stereolithographic Rapid Prototyping of Clear, Foldable, Non-Refractive Intraocular Lens Designs: A Proof-of-Concept Study

PURPOSE

A cataract is a cloudy area in the crystalline lens. Cataracts are the leading cause of blindness and the second cause of severe vision impairment worldwide. During cataract surgery, the clouded lens is extracted and replaced with an artificial intraocular lens, which restores the optical power. The fabrication of intraocular lenses using existing molding and lathing techniques is a complex and time-consuming process that limits the development of novel materials and designs. To overcome these limitations, we have developed a stereolithography-based process for producing models of clear lens designs without refractive function, serving as a proof of concept. This process has the potential to contribute toward new lens development, allowing for unlimited design iterations and an expanded range of materials for scientists to explore.

METHODS

Lens-like 3D objects without refractive function were fabricated by using stereolithography. A photopolymerizable resin containing 2-phenoxyethyl acrylate, poly (ethylene glycol) dimethacrylate, and a suitable photoinitiator was developed for the production of lens-like 3D object prototypes. The morphology of the printed devices was characterized by scanning electron microscopy. The transparency and thermal properties were analyzed using spectrophotometry and differential scanning calorimetry, respectively. The biocompatibility of the devices was investigated in a cultured human lens cell line (FHL-124), using a standard lactate dehydrogenase assay, and the lenses were folded and implanted in the human capsular bag model.

RESULTS

One-piece lens-like 3D objects without refractive function and with loop-haptic design were successfully fabricated using Stereolithography (SLA) technique. The resulting 3D objects were transparent, as determined by UV spectroscopy. The lactate dehydrogenase test demonstrated the tolerance of lens cells to the prototyping material, and apparent foldability and shape recovery was observed during direct injection into a human capsular bag model in vitro.

CONCLUSIONS

This proof-of-principle study demonstrated the potential and significance of the rapid prototyping process for research and development of lens-like 3D object prototypes, such as intraocular lenses.

Exploring the potential of intermetallic alloys as implantable biomaterials: A comprehensive review

This review delves into the utilization of intermetallic alloys (IMAs) as advanced biomaterials for medical implants, scrutinizing their conceptual framework, fabrication challenges, and diverse manufacturing techniques such as casting, powder metallurgy, and additive manufacturing. Manufacturing techniques such as casting, powder metallurgy, additive manufacturing, and injection molding are discussed, with specific emphasis on achieving optimal grain sizes, surface roughness, and mechanical properties. Post-treatment methods aimed at refining surface quality, dimensional precision, and mechanical properties of IMAs are explored, including the use of heat treatments to enhance biocompatibility and corrosion resistance. The review presents an in-depth examination of IMAs-based implantable biomaterials, covering lab-scale developments and commercial-scale implants. Specific IMAs such as Nickel Titanium, Titanium Aluminides, Iron Aluminides, Magnesium-based IMAs, Zirconium-based IMAs, and High-entropy alloys (HEAs) are highlighted, with detailed discussions on their mechanical properties, including strength, elastic modulus, and corrosion resistance. Future directions are outlined, with an emphasis on the anticipated growth in the orthopedic devices market and the role of IMAs in meeting this demand. The potential of porous IMAs in orthopedics is explored, with emphasis on achieving optimal pore sizes and distributions for enhanced osseointegration. The review concludes by highlighting the ongoing need for research and development efforts in IMAs technologies, including advancements in design and fabrication techniques.

New Generation of Osteoinductive and Antimicrobial Polycaprolactone-Based Scaffolds in Bone Tissue Engineering: A Review

With respect to other fields, bone tissue engineering has significantly expanded in recent years, leading not only to relevant advances in biomedical applications but also to innovative perspectives. Polycaprolactone (PCL), produced in the beginning of the 1930s, is a biocompatible and biodegradable polymer. Due to its mechanical and physicochemical features, as well as being easily shapeable, PCL-based constructs can be produced with different shapes and degradation kinetics. Moreover, due to various development processes, PCL can be made as 3D scaffolds or fibres for bone tissue regeneration applications. This outstanding biopolymer is versatile because it can be modified by adding agents with antimicrobial properties, not only antibiotics/antifungals, but also metal ions or natural compounds. In addition, to ameliorate its osteoproliferative features, it can be blended with calcium phosphates. This review is an overview of the current state of our recent investigation into PCL modifications designed to impair microbial adhesive capability and, in parallel, to allow eukaryotic cell viability and integration, in comparison with previous reviews and excellent research papers. Our recent results demonstrated that the developed 3D constructs had a high interconnected porosity, and the addition of biphasic calcium phosphate improved human cell attachment and proliferation. The incorporation of alternative antimicrobials-for instance, silver and essential oils-at tuneable concentrations counteracted microbial growth and biofilm formation, without affecting eukaryotic cells' viability. Notably, this challenging research area needs the multidisciplinary work of material scientists, biologists, and orthopaedic surgeons to determine the most suitable modifications on biomaterials to design favourable 3D scaffolds based on PCL for the targeted healing of damaged bone tissue.

Advanced 3D imaging and organoid bioprinting for biomedical research and therapeutic applications

Organoid cultures offer a valuable platform for studying organ-level biology, allowing for a closer mimicry of human physiology compared to traditional two-dimensional cell culture systems or non-primate animal models. While many organoid cultures use cell aggregates or decellularized extracellular matrices as scaffolds, they often lack precise biochemical and biophysical microenvironments. In contrast, three-dimensional (3D) bioprinting allows precise placement of organoids or spheroids, providing enhanced spatial control and facilitating the direct fusion for the formation of large-scale functional tissues in vitro. In addition, 3D bioprinting enables fine tuning of biochemical and biophysical cues to support organoid development and maturation. With advances in the organoid technology and its potential applications across diverse research fields such as cell biology, developmental biology, disease pathology, precision medicine, drug toxicology, and tissue engineering, organoid imaging has become a crucial aspect of physiological and pathological studies. This review highlights the recent advancements in imaging technologies that have significantly contributed to organoid research. Additionally, we discuss various bioprinting techniques, emphasizing their applications in organoid bioprinting. Integrating 3D imaging tools into a bioprinting platform allows real-time visualization while facilitating quality control, optimization, and comprehensive bioprinting assessment. Similarly, combining imaging technologies with organoid bioprinting can provide valuable insights into tissue formation, maturation, functions, and therapeutic responses. This approach not only improves the reproducibility of physiologically relevant tissues but also enhances understanding of complex biological processes. Thus, careful selection of bioprinting modalities, coupled with appropriate imaging techniques, holds the potential to create a versatile platform capable of addressing existing challenges and harnessing opportunities in these rapidly evolving fields.

Engineered Living Material Bioreactors with Tunable Mechanical Properties using Vat Photopolymerization

3D-printed engineered living materials (ELM) are promising bioproduction platforms for agriculture, biotechnology, sustainable energy, and green technology applications. However, the design of these platforms faces several challenges, such as the processability of these materials into complex form factors and control over their mechanical properties. Herein, ELM are presented as 3D-printed bioreactors with arbitrary shape geometries and tunable mechanical properties (moduli and toughness). Poly(ethylene glycol) diacrylate (PEGDA) is used as the precursor to create polymer networks that encapsulate the microorganisms during the vat photopolymerization process. A major limitation of PEGDA networks is their propensity to swell and fracture when submerged in water. The authors overcame this issue by adding glycerol to the resin formulation to 3D print mechanically tough ELM hydrogels. While polymer concentration affects the modulus and reduces bioproduction, ELM bioreactors still maintain their metabolic activity regardless of polymer concentration. These ELM bioreactors have the potential to be used in different applications for sustainable architecture, food production, and biomedical devices that require different mechanical properties from soft to stiff.

Embedded Printing of Hydrogels and Watery Suspensions of Cells in Patterned Granular Baths

Bioprinting within support media has emerged as the superior alternative to conventional extrusion printing. Not only because it allows for more freedom over the shapes that can be printed but also because it allows for the printing of inks that would not retain shape fidelity in freeform deposition such as watery liquids. Apart from functioning as mechanical support during embedded printing, hydrogel microparticle support media can provide the unique advantage of offering distinct chemotactic cues to cells printed in the baths by varying the composition of the hydrogel microparticles. There is great potential in compartmentalized granular baths consisting of different hydrogel particle materials in the field of tissue engineering, as these allow for the local inclusion of properties or cues to guide tissue development. In this work, we present a method to create compartmentalized embedding baths by printing multiple granular hydrogel materials that are widely used in tissue engineering. After adapting the volume fraction (φp) of the particles in the bath, we print within them using both inks composed of hydrogel or of cells and other particles suspended in watery liquid. Our process consists of the following three steps: First, the hydrogel microparticles are packed at a φp that allows them to be extruded while being reversibly jammed, facilitating the localized deposition of the granular media to form a compartmentalized bath. Second, each granular media is deposited in succession to create a packed suspension compartment, and by adding liquid post deposition, φp is reduced to allow for embedded printing. Finally, we demonstrate the printing of multiple inks within the compartmentalized embedding bath and highlight the distinct differences between using inks composed of hydrogels or inks composed of particles suspended in watery liquid. This approach combines the advantages of embedded printing through the use of granular media with the added ability to pattern multiple bioactive granular materials to locally affect the behavior of cells printed within the bath. We expect that this workflow will allow researchers to create spatially compartmentalized, customized bioactive embedding baths that allow for the embedded printing of inks composed of hydrogels, cells, and other particles adapted to their need.

Advances in 3D bioprinting for regenerative medicine applications

Biofabrication techniques allow for the construction of biocompatible and biofunctional structures composed from biomaterials, cells and biomolecules. Bioprinting is an emerging 3D printing method which utilizes biomaterial-based mixtures with cells and other biological constituents into printable suspensions known as bioinks. Coupled with automated design protocols and based on different modes for droplet deposition, 3D bioprinters are able to fabricate hydrogel-based objects with specific architecture and geometrical properties, providing the necessary environment that promotes cell growth and directs cell differentiation towards application-related lineages. For the preparation of such bioinks, various water-soluble biomaterials have been employed, including natural and synthetic biopolymers, and inorganic materials. Bioprinted constructs are considered to be one of the most promising avenues in regenerative medicine due to their native organ biomimicry. For a successful application, the bioprinted constructs should meet particular criteria such as optimal biological response, mechanical properties similar to the target tissue, high levels of reproducibility and printing fidelity, but also increased upscaling capability. In this review, we highlight the most recent advances in bioprinting, focusing on the regeneration of various tissues including bone, cartilage, cardiovascular, neural, skin and other organs such as liver, kidney, pancreas and lungs. We discuss the rapidly developing co-culture bioprinting systems used to resemble the complexity of tissues and organs and the crosstalk between various cell populations towards regeneration. Moreover, we report on the basic physical principles governing 3D bioprinting, and the ideal bioink properties based on the biomaterials' regenerative potential. We examine and critically discuss the present status of 3D bioprinting regarding its applicability and current limitations that need to be overcome to establish it at the forefront of artificial organ production and transplantation.

Applications, advancements, and challenges of 3D bioprinting in organ transplantation

To date, organ transplantation remains an effective method for treating end-stage diseases of various organs. In recent years, despite the continuous development of organ transplantation technology, a variety of problems restricting its progress have emerged one after another, and the shortage of donors is at the top of the list. Bioprinting is a very useful tool that has huge application potential in many fields of life science and biotechnology, among which its use in medicine occupies a large area. With the development of bioprinting, advances in medicine have focused on printing cells and tissues for tissue regeneration and reconstruction of viable human organs, such as the heart, kidneys, and bones. In recent years, with the development of organ transplantation, three-dimensional (3D) bioprinting has played an increasingly important role in this field, giving rise to many unsolved problems, including a shortage of organ donors. This review respectively introduces the development of 3D bioprinting as well as its working principles and main applications in the medical field, especially in the applications, and advancements and challenges of 3D bioprinting in organ transplantation. With the continuous update and progress of printing technology and its deeper integration with the medical field, many obstacles will have new solutions, including tissue repair and regeneration, organ reconstruction, etc., especially in the field of organ transplantation. 3D printing technology will provide a better solution to the problem of donor shortage.

3D Printing of Self-Healing Materials

This review article presents a comprehensive overview of the latest advances in the field of 3D printable structures with self-healing properties. Three-dimensional printing (3DP) is a versatile technology that enables the rapid manufacturing of complex geometric structures with precision and functionality not previously attainable. However, the application of 3DP technology is still limited by the availability of materials with customizable properties specifically designed for additive manufacturing. The addition of self-healing properties within 3D printed objects is of high interest as it can improve the performance and lifespan of structural components, and even enable the mimicking of living tissues for biomedical applications, such as organs printing. The review will discuss and analyze the most relevant results reported in recent years in the development of self-healing polymeric materials that can be processed via 3D printing. After introducing the chemical and physical self-healing mechanism that can be exploited, the literature review here reported will focus in particular on printability and repairing performances. At last, actual perspective and possible development field will be critically discussed.

The fabrication of the chitosan-based bioink for in vitro tissue repair and regeneration: A review

The repair and regeneration of the injured tissues or organs is a major challenge for biomedicine, and the emerging 3D bioprinting technology as a class of promising techniques in biomedical research for the development of tissue engineering and regenerative medicine. Chitosan-based bioinks, as the natural biomaterials, are considered as ideal materials for 3D bioprinting to design and fabricate the various scaffold due to their unique dynamic reversibility and fantastic biological properties. Our review aims to provide an overview of chitosan-based bioinks for in vitro tissue repair and regeneration, starting from modification of chitosan that affect these bioprinting processes. In addition, we summarize the advances in chitosan-based bioinks used in the various 3D printing strategies. Moreover, the biomedical applications of chitosan-based bioinks are discussed, primarily centered on regenerative medicine and tissue modeling engineering. Finally, current challenges and future opportunities in this field are discussed. The combination of chitosan-based bioinks and 3D bioprinting will hold promise for developing novel biomedical scaffolds for tissue or organ repair and regeneration.

Features of Vat-Photopolymerized Masters for Microfluidic Device Manufacturing

The growing interest in advancing microfluidic devices for manipulating fluids within micrometer-scale channels has prompted a shift in manufacturing practices, moving from single-component production to medium-size batches. This transition arises due to the impracticality of lab-scale manufacturing methods in accommodating the increased demand. This experimental study focuses on the design of master benchmarks 1-5, taking into consideration critical parameters such as rib width, height, and the relative width-to-height ratio. Notably, benchmarks 4 and 5 featured ribs that were strategically connected to the inlet, outlet, and reaction chamber of the master, enhancing their utility for subsequent replica production. Vat photopolymerization was employed for the fabrication of benchmarks 1-5, while replicas of benchmarks 4 and 5 were generated through polydimethylsiloxane casting. Dimensional investigations of the ribs and channels in both the master benchmarks and replicas were conducted using an optical technique validated through readability analysis based on the Michelson global contrast index. The primary goal was to evaluate the potential applicability of vat photopolymerization technology for efficiently producing microfluidic devices through a streamlined production process. Results indicate that the combination of vat photopolymerization followed by replication is well suited for achieving a minimum rib size of 25 µm in width and an aspect ratio of 1:12 for the master benchmark.

The Effect of Zinc Oxide on DLP Hybrid Composite Manufacturability and Mechanical-Chemical Resistance

The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99 ± 0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile stress in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile stress to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.

Methacrylated Cellulose Nanocrystals as Fillers for the Development of Photo-Cross-Linkable Cytocompatible Biosourced Formulations Targeting 3D Printing

Cellulose nanocrystals (CNCs) from cotton were functionalized in aqueous medium using methacrylic anhydride (MA) to produce methacrylated cellulose nanocrystals (mCNCs) with a degree of methacrylation (DM) up to 12.6 ± 0.50%. Dispersible as-prepared CNCs and mCNCs were then considered as reinforcing fillers for aqueous 3D-printable formulations based on methacrylated carboxymethylcellulose (mCMC). The rheological properties of such photo-cross-linkable aqueous formulations containing nonmodified CNCs or mCNCs at 0.2 or 0.5 wt% in 2 wt% mCMC were fully investigated. The influence of the presence of nanoparticles on the UV-curing kinetics and dimensions of the photo-cross-linked hydrogels was probed and 13C CP-MAS NMR spectroscopy was used to determine the maximum conversion ratio of methacrylates as well as the optimized time required for UV postcuring. The viscoelasticity of cross-linked hydrogels and swollen hydrogels was also studied. The addition of 0.5 wt% mCNC with a DM of 0.83 ± 0.040% to the formulation yielded faster cross-linking kinetics, better resolution, more robust cross-linked hydrogels, and more stable swollen hydrogels than pure mCMC materials. Additionally, the produced cryogels showed no cytotoxicity toward L929 fibroblasts. This biobased formulation could thus be considered for the 3D printing of hydrogels dedicated to biomedical purposes using vat polymerization techniques, such as stereolithography or digital light processing.

Advances in 3D Bioprinting of Biomimetic and Engineered Meniscal Grafts

The meniscus plays a crucial role in loads distribution and protection of articular cartilage. Meniscal injury can result in cartilage degeneration, loss of mechanical stability in the knee joint and ultimately lead to arthritis. Surgical interventions provide only short-term pain relief but fail to repair or regenerate the injured meniscus. Emerging tissue engineering approaches based on 3D bioprinting provide alternatives to current surgical methods for meniscus repair. In this review, the current bioprinting techniques employed in developing engineered meniscus grafts are summarized and discuss the latest strategies for mimicking the gradient structure, composition, and viscoelastic properties of native meniscus. Recent progress is highlighted in gene-activated matrices for meniscus regeneration as well. Finally, a perspective is provided on the future development of 3D bioprinting for meniscus repair, emphasizing the potential of this technology to revolutionize meniscus regeneration and improve patient outcomes.

A Comprehensive Mechanical Characterization of Subject-Specific 3D Printed Scaffolds Mimicking Trabecular Bone Architecture Biomechanics

This study presents a polymeric scaffold designed and manufactured to mimic the structure and mechanical compressive characteristics of trabecular bone. The morphological parameters and mechanical behavior of the scaffold were studied and compared with trabecular bone from bovine iliac crest. Its mechanical properties, such as modulus of elasticity and yield strength, were studied under a three-step monotonic compressive test. Results showed that the elastic modulus of the scaffold was 329 MPa, and the one for trabecular bone reached 336 MPa. A stepwise dynamic compressive test was used to assess the behavior of samples under various loading regimes. With microcomputed tomography (µCT), a three-dimensional reconstruction of the samples was obtained, and their porosity was estimated as 80% for the polymeric scaffold and 88% for trabecular bone. The full-field strain distribution of the samples was measured using in situ µCT mechanics and digital volume correlation (DVC). This provided information on the local microdeformation mechanism of the scaffolds when compared to that of the tissue. The comprehensive results illustrate the potential of the fabricated scaffolds as biomechanical templates for in vitro studies. Furthermore, there is potential for extending this structure and fabrication methodology to incorporate suitable biocompatible materials for both in vitro and in vivo clinical applications.

Review on vat photopolymerization additive manufacturing of bioactive ceramic bone scaffolds

Bone defects frequently occur in clinical settings due to trauma, disease, tumors, and other causes. The clinical use of autologous bones and allograft bone, however, has several limitations, such as limited sources, donor site morbidity, and immunological rejection. Nevertheless, there is newfound hope for regenerating and repairing bone defects through the development and integration of bone tissue engineering scaffold and additive manufacturing (AM) technology, also known as 3D printing. In particular, vat photopolymerization (VPP)-AM of bioactive ceramic bone scaffolds has garnered significant interest from interdisciplinary researchers in recent years. On the one hand, VPP-AM demonstrates clear advantages in printing accuracy and speed compared to other AM and non-AM technologies. On the other hand, bioactive ceramic materials exhibit superior bioactivity, biodegradability, and mechanical properties compared to metals, polymers, and bioinert ceramics, making them one of the most promising biomaterials for developing bone scaffolds. This paper reviews the research progress of VPP-AM of bioactive ceramic bone scaffolds, covering the process principles of various VPP-AM technologies, the performance requirements and preparation process of VPP ceramic slurry, the VPP process of bioactive ceramic bone scaffolds, and the research progress on different material types of VPP bioactive ceramic scaffolds. Firstly, we provide a brief introduction to the process principles and medical applications of various VPP technologies. Secondly, we explore the composition of the VPP ceramic slurry system, discussing the function of various components and their effects on printing quality. Thirdly, we delve into the performance requirements of bone scaffolds and summarize the research progress of VPP bioactive ceramic bone scaffolds of various material types including hydroxyapatite (HA), tricalcium phosphate (TCP), bioglass (BG), etc.; Finally, we discuss the challenges currently faced by VPP-AM bioactive ceramic bone scaffolds and propose possible development directions for the future.

Recent Progress of the Vat Photopolymerization Technique in Tissue Engineering: A Brief Review of Mechanisms, Methods, Materials, and Applications

Vat photopolymerization (VP), including stereolithography (SLA), digital light processing (DLP), and volumetric printing, employs UV or visible light to solidify cell-laden photoactive bioresin contained within a vat in a point-by-point, layer-by-layer, or volumetric manner. VP-based bioprinting has garnered substantial attention in both academia and industry due to its unprecedented control over printing resolution and accuracy, as well as its rapid printing speed. It holds tremendous potential for the fabrication of tissue- and organ-like structures in the field of regenerative medicine. This review summarizes the recent progress of VP in the fields of tissue engineering and regenerative medicine. First, it introduces the mechanism of photopolymerization, followed by an explanation of the printing technique and commonly used biomaterials. Furthermore, the application of VP-based bioprinting in tissue engineering was discussed. Finally, the challenges facing VP-based bioprinting are discussed, and the future trends in VP-based bioprinting are projected.

Application of Artificial Intelligence for Surface Roughness Prediction of Additively Manufactured Components

Additive manufacturing has gained significant popularity from a manufacturing perspective due to its potential for improving production efficiency. However, ensuring consistent product quality within predetermined equipment, cost, and time constraints remains a persistent challenge. Surface roughness, a crucial quality parameter, presents difficulties in meeting the required standards, posing significant challenges in industries such as automotive, aerospace, medical devices, energy, optics, and electronics manufacturing, where surface quality directly impacts performance and functionality. As a result, researchers have given great attention to improving the quality of manufactured parts, particularly by predicting surface roughness using different parameters related to the manufactured parts. Artificial intelligence (AI) is one of the methods used by researchers to predict the surface quality of additively fabricated parts. Numerous research studies have developed models utilizing AI methods, including recent deep learning and machine learning approaches, which are effective in cost reduction and saving time, and are emerging as a promising technique. This paper presents the recent advancements in machine learning and AI deep learning techniques employed by researchers. Additionally, the paper discusses the limitations, challenges, and future directions for applying AI in surface roughness prediction for additively manufactured components. Through this review paper, it becomes evident that integrating AI methodologies holds great potential to improve the productivity and competitiveness of the additive manufacturing process. This integration minimizes the need for re-processing machined components and ensures compliance with technical specifications. By leveraging AI, the industry can enhance efficiency and overcome the challenges associated with achieving consistent product quality in additive manufacturing.

3D Printing of Multimaterial Contact Lenses

3D printing of multimaterial objects is an emerging field with promising applications. The layer-by-layer material addition technique used in 3D printing enables incorporation of distinct functionalized materials into the specialized devices. However, very few studies have been performed on the usage of multimaterial 3D printing for printable photonic and wearable devices. Here, we employ vat photopolymerization-based 3D printing to produce multimaterial contact lenses, offering enhanced multiband optical filtration, which can be valuable for tackling ocular conditions such as color blindness. A combination of hydroxyethyl methacrylate (HEMA) and polyethylene glycol diacrylate (PEGDA) was used as the base hydrogel for 3D printing. Atto565 and Atto488 dyes were added to the hydrogel for wavelength filtering, each dye suitable for a different type of color blindness. Multimaterial disks and contact lenses, with separate sections containing distinct dyes, were 3D-printed, and their optical properties were studied. The characteristics of multimaterial printing were analyzed, focusing on the formation of a uniform multimaterial interface. In addition, a novel technique was developed for printing multiple dyed materials in complex lateral geometrical patterns, by employing suitable variations in CAD models and the UV curing time. It was observed that the multimaterial printing process does not negatively affect the optical properties of the contact lenses. The printed multimaterial contact lenses offered a combined multi-band color blindness correction due to the two dyes used. The resulting optical spectrum was a close match to the commercially available color blindness correction glasses.

Additive Manufacturing of Engineered Living Materials with Bio-augmented Mechanical Properties and Resistance to Degradation

Engineered living materials (ELMs) combine living cells with polymeric matrices to yield unique materials with programmable functions. While the cellular platform and the polymer network determine the material properties and applications, there are still gaps in our ability to seamlessly integrate the biotic (cellular) and abiotic (polymer) components into singular material, then assemble them into devices and machines. Herein, we demonstrated the additive-manufacturing of ELMs wherein bioproduction of metabolites from the encapsulated cells enhanced the properties of the surrounding matrix. First, we developed aqueous resins comprising bovine serum albumin (BSA) and poly(ethylene glycol diacrylate) (PEGDA) with engineered microbes for vat photopolymerization to create objects with a wide array of 3D form factors. The BSA-PEGDA matrix afforded hydrogels that were mechanically stiff and tough for use in load-bearing applications. Second, we demonstrated the continuous in situ production of L-DOPA, naringenin, and betaxanthins from the engineered cells encapsulated within the BSA-PEGDA matrix. These microbial metabolites bioaugmented the properties of the BSA-PEGDA matrix by enhancing the stiffness (L-DOPA) or resistance to enzymatic degradation (betaxanthin). Finally, we demonstrated the assembly of the 3D printed ELM components into mechanically functional bolts and gears to showcase the potential to create functional ELMs for synthetic living machines.

A flexible design framework to design graded porous bone scaffolds with adjustable anisotropic properties

Since the success of bone regenerative medicine depends on scaffold morphological and mechanical properties, numerous scaffolds designs have been proposed in the last decade, including graded structures that are suited to enhance tissue ingrowth. Most of these structures are based either on foams with a random pore definition, or on the periodic repetition of a unit cell (UC). These approaches are limited by the range of target porosities and obtained effective mechanical properties, and do not permit to easily generate a pore size gradient from the core to the periphery of the scaffold. In opposition, the objective of the present contribution is to propose a flexible design framework to generate various three-dimensional (3D) scaffolds structures including cylindrical graded scaffolds from the definition of a UC by making use of a non-periodic mapping. Conformal mappings are firstly used to generate graded circular cross-sections, while 3D structures are then obtained by stacking the cross-sections with or without a twist between different scaffold layers. The effective mechanical properties of different scaffold configurations are presented and compared using an energy-based efficient numerical method, pointing out the versatility of the design procedure to separately govern longitudinal and transverse anisotropic scaffold properties. Among these configurations, a helical structure exhibiting couplings between transverse and longitudinal properties is proposed and permits to extend the adaptability of the proposed framework. In order to investigate the capacity of common additive manufacturing techniques to fabricate the proposed structures, a subset of these configurations is elaborated using a standard SLA setup, and subjected to experimental mechanical testing. Despite observed geometric differences between the initial design and the actual obtained structures, the effective properties are satisfyingly predicted by the proposed computational method. Promising perspectives are offered concerning the design of self-fitting scaffolds with on-demand properties depending on the clinical application.

Influence of Trabecular Geometry on Scaffold Mechanical Behavior and MG-63 Cell Viability

In a scaffold-based approach for bone tissue regeneration, the control over morphometry allows for balancing scaffold biomechanical performances. In this experimental work, trabecular geometry was obtained by a generative design process, and scaffolds were manufactured by vat photopolymerization with 60% (P60), 70% (P70) and 80% (P80) total porosity. The mechanical and biological performances of the produced scaffolds were investigated, and the results were correlated with morphometric parameters, aiming to investigate the influence of trabecular geometry on the elastic modulus, the ultimate compressive strength of scaffolds and MG-63 human osteosarcoma cell viability. The results showed that P60 trabecular geometry allows for matching the mechanical requirements of human mandibular trabecular bone. From the statistical analysis, a general trend can be inferred, suggesting strut thickness, the degree of anisotropy, connectivity density and specific surface as the main morphometric parameters influencing the biomechanical behavior of trabecular scaffolds, in the perspective of tissue engineering applications.

Designing of gradient scaffolds and their applications in tissue regeneration

Gradient scaffolds are isotropic/anisotropic three-dimensional structures with gradual transitions in geometry, density, porosity, stiffness, etc., that mimic the biological extracellular matrix. The gradient structures in biological tissues play a major role in various functional and metabolic activities in the body. The designing of gradients in the scaffold can overcome the current challenges in the clinic compared to conventional scaffolds by exhibiting excellent penetration capacity for nutrients & cells, increased cellular adhesion, cell viability & differentiation, improved mechanical stability, and biocompatibility. In this review, the recent advancements in designing gradient scaffolds with desired biomimetic properties, and their implication in tissue regeneration applications have been briefly explained. Furthermore, the gradients in native tissues such as bone, cartilage, neuron, cardiovascular, skin and their specific utility in tissue regeneration have been discussed in detail. The insights from such advances using gradient-based scaffolds can widen the horizon for using gradient biomaterials in tissue regeneration applications.

Lignin-Based Materials for Additive Manufacturing: Chemistry, Processing, Structures, Properties, and Applications

The utilization of lignin, the most abundant aromatic biomass component, is at the forefront of sustainable engineering, energy, and environment research, where its abundance and low-cost features enable widespread application. Constructing lignin into material parts with controlled and desired macro- and microstructures and properties via additive manufacturing has been recognized as a promising technology and paves the way to the practical application of lignin. Considering the rapid development and significant progress recently achieved in this field, a comprehensive and critical review and outlook on three-dimensional (3D) printing of lignin is highly desirable. This article fulfils this demand with an overview on the structure of lignin and presents the state-of-the-art of 3D printing of pristine lignin and lignin-based composites, and highlights the key challenges. It is attempted to deliver better fundamental understanding of the impacts of morphology, microstructure, physical, chemical, and biological modifications, and composition/hybrids on the rheological behavior of lignin/polymer blends, as well as, on the mechanical, physical, and chemical performance of the 3D printed lignin-based materials. The main points toward future developments involve hybrid manufacturing, in situ polymerization, and surface tension or energy driven molecular segregation are also elaborated and discussed to promote the high-value utilization of lignin.

Synthesis, Characterization, and Digital Light Processing of a Hydrolytically Degradable Hyaluronic Acid Hydrogel

Numerous chemical modifications of hyaluronic acid (HA) have been explored for the formation of degradable hydrogels that are suitable for a variety of biomedical applications, including biofabrication and drug delivery. Thiol-ene step-growth chemistry is of particular interest due to its lower oxygen sensitivity and ability to precisely tune mechanical properties. Here, we utilize an aqueous esterification route via reaction with carbic anhydride to synthesize norbornene-modified HA (NorHACA) that is amenable to thiol-ene crosslinking to form hydrolytically unstable networks. NorHACA is first synthesized with varying degrees of modification (∼15-100%) by adjusting the ratio of reactive carbic anhydride to HA. Thereafter, NorHACA is reacted with dithiol crosslinker in the presence of visible light and photoinitiator to form hydrogels within tens of seconds. Unlike conventional NorHA, NorHACA hydrogels are highly susceptible to hydrolytic degradation through enhanced ester hydrolysis. Both the mechanical properties and the degradation timescales of NorHACA hydrogels are tuned via macromer concentration and/or the degree of modification. Moreover, the degradation behavior of NorHACA hydrogels is validated through a statistical-co-kinetic model of ester hydrolysis. The rapid degradation of NorHACA hydrogels can be adjusted by incorporating small amounts of slowly degrading NorHA macromer into the network. Further, NorHACA hydrogels are implemented as digital light processing (DLP) resins to fabricate hydrolytically degradable scaffolds with complex, macroporous structures that can incorporate cell-adhesive sites for cell attachment and proliferation after fabrication. Additionally, DLP bioprinting of NorHACA hydrogels to form cell-laden constructs with high viability is demonstrated, making them useful for applications in tissue engineering and regenerative medicine.

Recent advances in 3D-printed polylactide and polycaprolactone-based biomaterials for tissue engineering applications

The three-dimensional printing (3DP) also known as the additive manufacturing (AM), a novel and futuristic technology that facilitates the printing of multiscale, biomimetic, intricate cytoarchitecture, function-structure hierarchy, multi-cellular tissues in the complicated micro-environment, patient-specific scaffolds, and medical devices. There is an increasing demand for developing 3D-printed products that can be utilized for organ transplantations due to the organ shortage. Nowadays, the 3DP has gained considerable interest in the tissue engineering (TE) field. Polylactide (PLA) and polycaprolactone (PCL) are exemplary biomaterials with excellent physicochemical properties and biocompatibility, which have drawn notable attraction in tissue regeneration. Herein, the recent advancements in the PLA and PCL biodegradable polymer-based composites as well as their reinforcement with hydrogels and bio-ceramics scaffolds manufactured through 3DP are systematically summarized and the applications of bone, cardiac, neural, vascularized and skin tissue regeneration are thoroughly elucidated. The interaction between implanted biodegradable polymers, in-vivo and in-vitro testing models for possible evaluation of degradation and biological properties are also illustrated. The final section of this review incorporates the current challenges and future opportunities in the 3DP of PCL- and PLA-based composites that will prove helpful for biomedical engineers to fulfill the demands of the clinical field.

Next Evolution in Organ-Scale Biofabrication: Bioresin Design for Rapid High-Resolution Vat Polymerization

The field of bioprinting has made significant advancements in recent years and allowed for the precise deposition of biomaterials and cells. However, within this field lies a major challenge, which is developing high resolution constructs, with complex architectures. In an effort to overcome these challenges a biofabrication technique known as vat polymerization is being increasingly investigated due to its high fabrication accuracy and control of resolution (µm scale). Despite the progress made in developing hydrogel precursors for bioprinting techniques, such as extrusion-based bioprinting, there is a major lack in developing hydrogel precursor bioresins for vat polymerization. This is due to the specific unique properties and characteristics required for vat polymerization, from lithography to the latest volumetric printing. This is of major concern as the shortage of bioresins available has a significant impact on progressing this technology and exploring its full potential, including speed, resolution, and scale. Therefore, this review discusses the key requirements that need to be addressed in successfully developing a bioresin. The influence of monomer architecture and bioresin composition on printability is described, along with key fundamental parameters that can be altered to increase printing accuracy. Finally, recent advancements in bioresins are discussed together with future directions.

A high-performance GelMA-GelMA homogeneous double-network hydrogel assisted by 3D printing

Gelatin methacryloyl (GelMA) is a popular photocrosslinkable hydrogel that has been widely utilized in tissue engineering and regenerative medicine fields due to its excellent biocompatibility, biodegradability and cell response. However, the lack of mechanical properties limits its application. In the present study, a method for the preparation of a GelMA-GelMA (G-G) homogeneous double-network (DN) hydrogel to improve mechanical strength based on DLP 3D printing is proposed. The G-G DN hydrogel was fabricated and characterized in terms of microstructure, mechanical properties and rheological behavior. By modifying the degree of substitution (DS), the polymer concentration of double network crosslinking and the soak time, the novel G-G DN hydrogel could significantly improve the properties of strength, self-recovery and fatigue resistance. After all, the novel porous composite hydrogel (G-G DN hydrogel) could achieve more than twice that of the pure GelMA hydrogel, better fatigue resistance and printable ability. Therefore, it can be a potential choice of applications attracting great attention for its mechanical properties, great transmittance and biocompatibility.

3D direct printing of mechanical and biocompatible hydrogel meta-structures

Direct Ink Writing (DIW) has demonstrated great potential as a versatile method to 3D print multifunctional structures. In this work, we report the implementation of hydrogel meta-structures using DIW at room temperature, which seamlessly integrate large specific surface areas, interconnected porous characteristics, mechanical toughness, biocompatibility, and water absorption and retention capabilities. Robust but hydrophobic polymers and weakly crosslinked nature-origin hydrogels form a balance in the self-supporting ink, allowing us to directly print complex meta-structures without sacrificial materials and heating extrusion. Mechanically, the mixed bending or stretching of symmetrical re-entrant cellular lattices and the unique curvature patterns are combined to provide little lateral expansion and large compressive energy absorbance when external forces are applied on the printed meta-structures. In addition, we have successfully demonstrated ear, aortic valve conduits and hierarchical architectures. We anticipate that the reported 3D meta-structured hydrogel would offer a new strategy to develop functional biomaterials for tissue engineering applications in the future.

Thermal, Mechanical and Biocompatibility Analyses of Photochemically Polymerized PEGDA250 for Photopolymerization-Based Manufacturing Processes

Novel fabrication techniques based on photopolymerization enable the preparation of complex multi-material constructs for biomedical applications. This requires an understanding of the influence of the used reaction components on the properties of the generated copolymers. The identification of fundamental characteristics of these copolymers is necessary to evaluate their potential for biomaterial applications. Additionally, knowledge of the properties of the starting materials enables subsequent tailoring of the biomaterials to meet individual implantation needs. In our study, we have analyzed the biological, chemical, mechanical and thermal properties of photopolymerized poly(ethyleneglycol) diacrylate (PEGDA) and specific copolymers with different photoinitiator (PI) concentrations before and after applying a post treatment washing process. As comonomers, 1,3-butanediol diacrylate, pentaerythritol triacrylate and pentaerythritol tetraacrylate were used. The in vitro studies confirm the biocompatibility of all investigated copolymers. Uniaxial tensile tests show significantly lower tensile strength (82% decrease) and elongation at break (76% decrease) values for washed samples. Altered tensile strength is also observed for different PI concentrations: on average, 6.2 MPa for 1.25% PI and 3.1 MPa for 0.5% PI. The addition of comonomers lowers elongation at break on average by 45%. Moreover, our observations show glass transition temperatures (Tg) ranging from 27 °C to 56 °C, which significantly increase with higher comonomer content. These results confirm the ability to generate biocompatible PEGDA copolymers with specific thermal and mechanical properties. These can be considered as resins for various additive manufacturing-based applications to obtain personalized medical devices, such as drug delivery systems (DDS). Therefore, our study has advanced the understanding of PEGDA multi-materials and will contribute to the future development of tools ensuring safe and effective individual therapy for patients.

Stereolithographic Visible-Light Printing of Poly(l-glutamic acid) Hydrogel Scaffolds

Bioprinting is a promising fabrication technique aimed at developing biologically functional, tissue-like constructs for various biomedical applications. Among the different bioprinting approaches, vat polymerization-based techniques offer the highest feature resolution compared to more commonly used extrusion-based methods and therefore have greater potential to be utilized for printing complex hierarchical tissue architectures. Although significant efforts have been directed toward harnessing digital light processing techniques for high-resolution bioprinting, the use of stereolithography (SLA) setups for producing distinct hydrogel filaments smaller than 20 μm has received less attention. Improving the bioprinting resolution is still a technical challenge that must consider both the practical limitations of the bioprinter apparatus and the formulation of the cytocompatible bioresin. In this study, we developed a novel bioresin compatible with SLA and capable of printing high-resolution features. This resin, composed of a biosynthetic polypeptide poly(l-glutamic acid) functionalized with tyramine moieties (PLGA-Tyr), was crosslinked using a visible-light photoinitiator system. Varying concentrations of PLGA-Tyr and the co-photoinitiator were evaluated for the hydrogel system's gelation ability, swelling characteristics, degradation profiles, mechanical properties, and cell viability post-encapsulation. This study introduces a custom-built, cost-effective, visible-light SLA bioprinting system named the "MicroNC". Using the newly developed visible-light bioresin, we demonstrated for the first time the ability to fabricate hydrogel scaffolds with well-resolved filaments (less than 8 μm in width) capable of supporting cell viability and proliferation and directing cellular morphology at the single-cell level for up to 14 days. Overall, these experiments have underscored the exciting potential of using the visible-light-photoinitiated PLGA-Tyr material system for developing physiologically relevant in vitro hydrogel scaffolds with feature resolutions comparable to the dimensions of individual human cells for a wide range of biomedical applications.

Success Factors of Additive Manufactured Root Analogue Implants

Dental implantation is an effective method for the treatment of loose teeth, but the threaded dental implants used in the clinic cannot match with the tooth extraction socket. A root analogue implant (RAI) has the congruence shape, which reduces the damage to bone and soft tissue. Additive manufacturing (AM) technologies have the advantages of high precision, flexibility, and easy operation, becoming the main manufacturing method of RAI in basic research. The purpose of this systematic review is to summarize AM technologies used for RAI manufacturing as well as the factors affecting successful implantation. First, it introduces the AM technologies according to different operating principles and summarizes the advantages and disadvantages of each method. Then the influences of materials, structure design, surface characteristics, implant site, and positioning are discussed, providing reference for designers and dentists. Finally, it addresses the gap between basic research and clinical application for additive manufactured RAIs and discusses the current challenges and future research directions for this field.

Meniscus regeneration by 3D printing technologies: Current advances and future perspectives

Meniscal tears are a frequent orthopedic injury commonly managed by conservative strategies to avoid osteoarthritis development descending from altered biomechanics. Among cutting-edge approaches in tissue engineering, 3D printing technologies are extremely promising guaranteeing for complex biomimetic architectures mimicking native tissues. Considering the anisotropic characteristics of the menisci, and the ability of printing over structural control, it descends the intriguing potential of such vanguard techniques to meet individual joints’ requirements within personalized medicine. This literature review provides a state-of-the-art on 3D printing for meniscus reconstruction. Experiences in printing materials/technologies, scaffold types, augmentation strategies, cellular conditioning have been compared/discussed; outcomes of pre-clinical studies allowed for further considerations. To date, translation to clinic of 3D printed meniscal devices is still a challenge: meniscus reconstruction is once again clear expression of how the integration of different expertise (e.g., anatomy, engineering, biomaterials science, cell biology, and medicine) is required to successfully address native tissues complexities.

Vat Photopolymerization Additive Manufacturing of Functionally Graded Materials: A Review

Functionally Graded Materials (FGMs) offer discrete or continuously changing properties/compositions over the volume of the parts. The widespread application of FGMs was not rapid enough in the past due to limitations of the manufacturing methods. Significant developments in manufacturing technologies especially in Additive Manufacturing (AM) enable us nowadays to manufacture materials with specified changes over the volume/surface of components. The use of AM methods for the manufacturing of FGMs may allow us to compensate for some drawbacks of conventional methods and to produce complex and near-net-shaped structures with better control of gradients in a cost-efficient way. Vat Photopolymerization (VP), a type of AM method that works according to the principle of curing liquid photopolymer resin layer-by-layer, has gained in recent years high importance due to its advantages such as low cost, high surface quality control, no need to support structures, no limitation in the material. This article reviews the state-of-art and future potential of using VP methods for FGM manufacturing. It was concluded that improvements in printer hardware setup and software, design aspects and printing methodologies will accelerate the use of VP methods for FGMs manufacturing.

Polyoxazoline Hydrogels fabricated by Stereolithography

The development of hydrogel materials in additive manufacturing displaying stiff and strong mechanical properties while maintaining high water uptake, remains a great challenge. Taking advantage of the versatility of poly(oxazoline)...

A Review on Advanced Manufacturing for Hydrogen Storage Applications

Hydrogen is a notoriously difficult substance to store yet has endless energy applications. Thus, the study of long-term hydrogen storage, and high-pressure bulk hydrogen storage have been the subject of much research in the last several years. To create a research path forward, it is important to know what research has already been done, and what is already known about hydrogen storage. In this review, several approaches to hydrogen storage are addressed, including high-pressure storage, cryogenic liquid hydrogen storage, and metal hydride absorption. Challenges and advantages are offered based on reported research findings. Since the project looks closely at advanced manufacturing, techniques for the same are outlined as well. There are seven main categories into which most rapid prototyping styles fall. Each is briefly explained and illustrated as well as some generally accepted advantages and drawbacks to each style. An overview of hydrogen adsorption on metal hydrides, carbon fibers, and carbon nanotubes are presented. The hydrogen storage capacities of these materials are discussed as well as the differing conditions in which the adsorption was performed under. Concepts regarding storage shape and materials accompanied by smaller-scale advanced manufacturing options for hydrogen storage are also presented.