Influence of Total Knee Arthroplasty on Patellar Kinematics and Patellofemoral Pressure

Patellar Overstuffing in Total Knee Arthroplasty Results in Decreased Extensor Mechanism Efficiency

Patellofemoral offset is influenced by patellar thickness in total knee arthroplasty (TKA), with effects on extensor mechanism efficiency (EME), patellar contact moment arm (PCMA), and patellar contact force (PCF). This study utilized a computational model to better quantify these measures during knee range of motion (ROM).A computational model of a cruciate-sacrificing, posterior-stabilized TKA design was used to quantify moments at knee flexion angles from 0° to 135° when patella thickness was increased ("overstuffed") or decreased ("understuffed") by 2 mm and 5 mm from normal. Outcomes included changes in EME, PCMA, PCF, tibial tubercle moment arm (TTMA), and the quadriceps moment arm (QMA).Overstuffing of the patellofemoral articulation by 2 mm and 5 mm decreased EME up to 12 and 28%, respectively, with an 8% and 16% increase in EME with understuffing that peaked at 25° knee flexion. The QMA increased up to 5 and 12% with overstuffing by 2 mm and 5 mm and decreased up to 5% and 14% with understuffing, respectively. There was an increase in the PCMA/PCF, which opposed the QMA, up to 8%/17% and 16%/39% with overstuffing by 2 mm and 5 mm, respectively. The PCMA/PCF decreased up to 3%/12% and 8%/33% with understuffing by 2 mm and 5 mm, respectively.In this computational model, increased patellofemoral offset resulting in overstuffing of the patella resulted in decreased EME and increased PCMA and PCF during knee ROM. This may contribute to abnormal patellofemoral mechanics and a potential etiology for anterior knee pain and quadriceps weakness after TKA.

Current status of bicompartmental arthroplasty

BACKGROUND

Bicompartmental arthroplasty (BCA) serves as a less invasive alternative to total knee arthroplasty. This review aims to present the current status of BCA. BODY: Recent literature on BCA was reviewed and synthesized from the perspectives of function, radiological assessment, patient satisfaction, survival rate, patellar tracking, satisfaction survey, and revision rate.

CONCLUSION

BCA is beneficial for patients with bicompartmental arthritis and those suffering from deterioration in other compartments after unicompartmental knee arthroplasty (UKA). Compared to total knee arthroplasty, BCA reduces trauma, accelerates recovery, and improves sports ability. While BCA is evolving towards a more exciting future, more clinical studies are warranted to exploit its potential and validate its efficacy, eventually improving outcomes and patient satisfaction.

Clinical Study and Finite Element Analysis on the Effects of Pseudo-Patella Baja After TKA

OBJECTIVE

Pseudo-patella baja (PPB) was one of the complications after total knee arthroplasty (TKA). This complication may be closely related to the occurrence of knee joint movement limitation and pain after TKA. This study aimed to investigate whether PPB affects clinical outcomes after TKA and to study the biomechanical effects of PPB after TKA.

METHODS

This study was a retrospective case series of 462 eligible patients (563 knees). Clinical evaluation was performed using the visual analogue scale (VAS), the Hospital for Special Surgery (HSS), the Western Ontario McMaster University Osteoarthritis Index (WOMAC) scoring systems, the 5-Level EuroQol Generic Health Index (EQ-5D-5L), the Forgotten Joint Score-12 (FJS-12), and patient satisfaction. CT and MRI scans of two healthy left knees and TKA prostheses were taken; 3D models including PPB, True patella baja (TPB), normal patella, and patella alta (PA) were created in FEA and applied load along the direction of quadriceps femoris. T-test, Mann-Whitney U-test, chi-squared (χ 2) test, and analysis of variance (ANOVA) were performed using GraphPad Prism (Version 8, GraphPad Software, USA). A statistically significant difference was considered at p < 0.05 with bilateral α.

RESULTS

The VAS, HSS, WOMAC, EQ-5D-5L, FJS-12, and patient satisfaction scores in the PPB and TPB groups were significantly worse than those in the patella normal (PN) group (p < 0.05). The PPB group found a positive correlation between Blackburne-Peel index (BPI) and FJS-12 score. PPB showed lower contact stress of patellofemoral joint compared to TPB when knee flexion was less than < 90° (p < 0.01), but no significant difference when flexion was more than > 90° (p > 0.05) in the finite element model with Patella baja (PB). The contact area of the patellofemoral joint tended to increase with the deepening of knee flexion, and decreased after reaching the peak value. The contact area of the patellofemoral joint tended to decrease with the increase in patellar height. There was no significant difference in the contact area of the patellofemoral joint among different patellar heights and different degrees of knee flexion (p > 0.05).

CONCLUSION

PPB after TKA may increase patellofemoral joint stress and postoperative complications like anterior knee pain.

The Optimal Variation Range of Posterior Condylar Offset Associated with Positive Clinical Outcomes of Primary Total Knee Arthroplasty: A Retrospective Analysis

OBJECTIVE

Posterior condylar offset (PCO) and anterior condylar offset (ACO) exert an influence on the sagittal alignment in total knee arthroplasty (TKA). However, there is no common consensus that the variation range of posterior condylar offset (PCO) is associated with patient-reported outcome measures (PROMs) and the optimum variation range of PCO. This study aims to investigate the correlation between PCO and the PROMs of primary TKA for osteoarthritis (OA) and find out the optimal variation range of the PCO.

METHODS

In this study, we performed a radiographic analysis of 106 patients (112 knees) with primary TKA. Patients were divided into two cohorts (A and B) according to the Western Ontario and McMaster Universities Osteoarthritis index (WOMAC). Correlations between the sagittal parameter and WOMAC were investigated using univariate and multivariate analysis. The receiver operating characteristic (ROC) curve was used to establish the cut-off value for the optimal variation range. We then further investigated how different variation range affects the WOMAC subscale score and forgotten-joint-score-12 (FJS-12).

RESULTS

Univariate analysis revealed a correlation between the variation range of PCO (p < 0.01), ACO (p < 0.01) and PROMs. Multivariate analysis showed that only PCO was associated with PROMs. In the ROC graph, the cut-off value of the variation range of PCO is 2.85 mm (AUC = 0.66, Youden index = 0.26). The WOMAC functional ability score of the group outside the PCO variation range of 2.85 mm significantly increased compared to the group within the range.

CONCLUSION

In this study, PCO variation was significantly associated with clinical outcomes in TKA and the optimal PCO variation range was within 2.85 mm. Maintaining the PCO variation within 2.85 mm could enhance functional recovery and patient satisfaction.

Enhancing total knee arthroplasty outcomes: the role of individualized femoral sagittal alignment in robotic-assisted surgery - A randomized controlled trial

BACKGROUND

Optimal sagittal alignment of the femoral prosthesis is critical to the success of total knee arthroplasty (TKA). While robotic-assisted TKA can improve alignment accuracy, the efficacy of default femoral alignment versus individualized alignment remains under scrutiny. This study aimed to compare the differences in prosthetic alignment, anatomical restoration, and clinical outcomes between individualized femoral sagittal alignment and default sagittal alignment in robotic-assisted TKA.

METHODS

In a prospective randomised controlled trial, 113 patients (120 knees) underwent robotic-assisted TKA were divided into two groups: 61 with individualized femoral flexion (individualized alignment group) and 59 with default 3-5° flexion (default alignment group). The individualized alignment was based on the distal femoral sagittal anteverted angle (DFSAA), defined as the angle between the mechanical and distal anatomical axes of the femur. The radiographic and clinical outcomes were compared.

RESULTS

Despite similar postoperative femoral flexion angles between groups (P = 0.748), the individualized alignment group exhibited significantly lower incidences of femoral prosthesis extension and higher rates of optimal 0-3° prosthesis flexion (9.8% vs. 27.1%, P = 0.014,78.7% vs. 55.9%, p = 0.008, respectively). The individualized alignment group also demonstrated more favourable changes in sagittal anatomy, with higher maintenance of postoperative anterior femoral offset within 1 mm (54.1% vs. 33.9%, P = 0.026) and posterior condylar offset within 1 mm and 2 mm (44.3% vs. 25.4%, p = 0.031,73.8% vs. 50.8%, p = 0.010, respectively). Although slight improvement in the Hospital for Special Surgery Knee Score (HSS) at three months was observed (P = 0.045), it did not reach a minimal clinically important difference.

CONCLUSION

Individualized tailoring of femoral sagittal alignment in robotic-assisted total knee arthroplasty (TKA) enhances prosthetic alignment and anatomical restoration, suggesting potential improvements in postoperative outcomes.

Internal rotational patellar resection and patella alta induced patellar maltracking in total knee arthroplasty: intraoperative measurement of the patellofemoral pressure

BACKGROUND

Anterior knee pain due to patellar maltracking following total knee arthroplasty (TKA) reduces patients' satisfaction. This study aimed to determine the patellofemoral pressure (PFP) in patients with favorable patellar tracking (FT) and impaired patellar tracking (IT) following TKA, the factors causing patellar maltracking, and the effect of lateral retinacular release (LRR) on patients with IT.

METHODS

Forty-four patients with varus knee osteoarthritis undergoing cruciate-retaining TKA were enrolled. After component implantation, patients with a separation of ≥ 2 mm of the patellar medial facet from the medial femoral trochlea throughout knee range of motion were classified into the IT group; meanwhile, the others were classified into the FT group. PFP was measured intraoperatively in three phases: (1) with the resurfaced patella (RP); (2) with the resurfaced patella and knee (RPK); and (3) when LRR was performed in IT (post-LRR). The PFPs at 0°, 90°, 120°, and 135° knee flexion were compared between FT and IT using the Mann-Whitney U test. Pairwise comparison of the PFP in IT between RPK and post-LRR was performed using the Wilcoxon signed-rank test. Correlations between PFP and pre- and postoperative radiographic parameters, such as hip-knee-ankle angle, lateral distal femoral angle, medial proximal tibial angle, anterior femoral offset, Insall-Salvati ratio (ISR), patellar tilt, and patellar resection angle (PRA), were evaluated using Spearman's rank correlation coefficients.

RESULTS

High lateral PFP in the knee flexion position led to patellar maltracking. Patients with IT (n = 24) had higher lateral and lower medial PFP than did patients with FT (n = 20) at 90°, 120°, and 135° knee flexion in RP and RPK. LRR in IT reduced the lateral PFP in the knee flexion position. PRA and ISR were correlated with the lateral PFP at no less than 90° in RP and RPK.

CONCLUSIONS

This study demonstrated that internal rotational patellar resection, which resulted in a thick medial patellar remnant and a thin lateral counterpart, and patella alta were the causative factors of high lateral PFP, which induced patellar maltracking after TKA. Surgeons should avoid internal rotational patellar resection to achieve FT and perform LRR in patients with patellar maltracking.

The Fate of Unresurfaced Patellae in Contemporary Total Knee Arthroplasty: Early to Midterm Results

BACKGROUND

Leaving the patella unresurfaced in total knee arthroplasty (TKA) has increased significantly over the past decade in the United States, likely due to modern patella-friendly implants, complications with resurfacing, and the knowledge that historical studies were scientifically confounded. This study evaluated revision-free survivorship out to 8.5 years in a cohort of contemporary primary TKAs with patella-friendly femoral components and unresurfaced patellae.

METHODS

A total of 1,053 consecutive primary TKAs with unresurfaced patellae were retrospectively reviewed. A selective patellar nonresurfacing protocol was used for all cases. Kaplan-Meier survivorship estimates were calculated based on patellar revision and the latest follow-up. An aggressive lateral patellar facetectomy was performed in 78% (823 of 1,053) of cases. The cohort was 62% women and 43% American Society of Anesthesiologists physical status classification I or II with a mean age and body mass index of 65 years (range, 35 to 94) and 35 kg/m2 (range, 18 to 65), respectively.

RESULTS

A total of 4 (0.4%, 4 of 1,053) unresurfaced patellae were revised. Three were resurfaced as part of other procedures: 2 for global instability and one for aseptic loosening at a mean of 1.6 years; and one patella was resurfaced by an outside surgeon for unexplained pain. The all-cause revision-free survivorship estimate specifically related to the patella was 98.9% (95% confidence interval, 98 to 100) out to 8.5 years. No significant difference in survivorship was related to patellae with or without a lateral patellar facetectomy (99.5 versus 98.1%, P ≥ .191); however, 3 of 4 patellar revisions occurred in TKAs without a lateral patellar facetectomy (P = .035).

CONCLUSIONS

The results of this study demonstrate excellent revision-free survivorship related to unresurfaced patellae, particularly when a lateral facetectomy was performed. These early to midterm results using modern patella-friendly femoral components are promising and comparable to resurfaced patellae in the literature.

LEVEL OF EVIDENCE

IV.

Comparison of the Kinematics and Laxity of Total Knee Arthroplasty Bearing Designs Stabilized With Specimen-Specific Virtual Ligaments on a Joint Motion Simulator

A variety of total knee arthroplasty (TKA) designs offer increased congruency bearing options, primarily to compensate for a loss of posterior cruciate ligament (PCL) function. However, their efficacy in providing sufficient stability under different circumstances requires further investigation. The preclinical testing of prosthesis components on joint motion simulators is useful for quantifying how design changes affect joint stability. However, this type of testing may not be clinically relevant because surrounding ligaments are either ignored or greatly simplified. This study aimed to assess the kinematics and stability of TKA joints during various motions using condylar-stabilized (CS) bearings without a PCL versus cruciate-retaining (CR) bearings with an intact PCL. TKA prosthetic components were tested on a joint motion simulator while being stabilized with five different sets of specimen-specific virtual ligament envelopes. In comparison to CR knees, CS knees without a PCL exhibited a greater amount of posterior tibial displacement laxity, with a mean increase of 2.7±2.1 mm (p = 0.03). Additionally, significant differences were observed in the anterior-posterior kinematics of the knee joint during activities of daily living (ADL) between the two designs. These results were consistent with previous cadaveric investigations, which indicated that CS knees without a PCL are less resistant to posterior tibial displacement than CR knees with one. This study employing virtual ligaments confirms previous findings that the raised anterior lip of some CS bearings may not completely compensate for the absence of the PCL; however, as both studies used reduced joint contact forces, the contributions of this design feature may be attenuated.

Sagittal Patellar Offset Ratio Can Be a Predictor of Anterior Knee Pain after Primary Total Knee Arthroplasty without Patella Resurfacing

BACKGROUND

Anterior knee pain (AKP) is an issue that persists even after successful total knee arthroplasty (TKA). In some patients, reasons for AKP occurrence are known, but it is unexplained in some others despite the patellofemoral joint being thought to be the main focus of pain. We investigated the relationship between unexplained AKP and the patellofemoral joint in the sagittal plane after primary TKA.

METHODS

We evaluated 372 knees of 317 patients retrospectively, who had completed a minimum 24-month follow-up. We divided them into two groups according to the presence of AKP. Sagittal patellar offset ratio (SPOR), anterior femoral offset ratio (AFOR), and Insall-Salvati ratio (ISR) were measured on lateral X-rays. Clinical outcomes were evaluated using the Oxford knee score (OKS) and WOMAC pre-and postoperatively, and AKP was evaluated using a visual analog scale (VAS) postoperatively.

RESULTS

Between non-AKP and AKP groups, SPOR (p < 0.001) and AFOR (p = 0.03) were significantly different but not ISR (p = 0.89). SPOR and AFOR were found to be two independent risk factors that may predict the likelihood of AKP. Receiver operating characteristic (ROC) analysis revealed that AFOR is a poor value, whereas SPOR is a reasonable predictive value. No correlation between SPOR and postoperative OKS (p = 0.92) and WOMAC (p = 0.25) and no correlation between AFOR and postoperative OKS (p = 0.44) and WOMAC (p = 0.58) were found.

CONCLUSION

We found that SPOR is a good predictive tool with a cutoff value of 46.4% and 91.5% sensitivity for AKP and its increased ratio increases the probability of AKP following TKA. Considering that the patellar offset will not change, especially in patients without patella resurfacing, care should be taken not to increase the anterior femoral offset.

Establishing the Minimal Clinically Important Difference and Patient Acceptable Symptomatic State following Patellofemoral Inlay Arthroplasty for Visual Analog Scale Pain, Western Ontario and McMaster Universities Arthritis Index, and Lysholm Scores

BACKGROUND

The purposes of the study were to define the minimal clinically important difference (MCID) and patient acceptable symptomatic state (PASS) after patello-femoral inlay arthroplasty (PFA) and to identify factors predictive for the achievement of clinically important outcomes (CIOs).

METHODS

A total of 99 patients who underwent PFA between 2009 and 2019 and had a minimum of 2-year postoperative follow-up were enrolled in this retrospective monocentric study. Included patients had a mean age of 44 years (range, 21 to 79). The MCID and PASS were calculated using an anchor-based approach for the visual analog scale (VAS) pain, Western Ontario and McMaster Universities Arthritis Index (WOMAC), and Lysholm patient-reported outcome measures. Factors associated with CIO achievement were determined using multivariable logistic regression analyses.

RESULTS

The established MCID thresholds for clinical improvement were -2.46 for the VAS pain score, -8.5 for the WOMAC score, and + 25.4 for the Lysholm score. Postoperative scores corresponding to the PASS were <2.55 for the VAS pain score, <14.6 for the WOMAC score, and >52.5 points for the Lysholm score. Preoperative patellar instability and concomitant medial patello-femoral ligament reconstruction were independent positive predictors of reaching both MCID and PASS. Additionally, inferior baseline scores and age were predictive of achieving MCID, whereas superior baseline scores and body mass index were predictive of achieving PASS.

CONCLUSION

This study determined the thresholds of MCID and PASS for the VAS pain, WOMAC, and Lysholm scores following PFA implantation at 2-year follow-up. The study demonstrated a predictive role of patient age, body mass index, preoperative patient-reported outcome measure scores, preoperative patellar instability, and concomitant medial patello-femoral ligament reconstruction in the achievement of CIOs.

LEVEL OF EVIDENCE

Prognostic Level IV.

The effect of femoral prosthesis design on patellofemoral contact stresses in total knee arthroplasty: a case-control study with mid-term follow-up minimum 3-year follow-up

BACKGROUND

To investigate the differences in postoperative patellofemoral pressures and patellar tracking during at least three years of follow-up in patients using three prostheses of different designs in total knee arthroplasty (TKA) without patellar resurfacing.

METHODS

RADIOGRAPHIC INVESTIGATIONS: The study included 401 patients who had a total of 480 knee prostheses implanted without patellar resurfacing. The prostheses used were Genesis II (external rotation design of femoral prosthesis), Triathlon (design with deep trochlear grooves), and Gemini MK II (deepening of trochlear groove and lateral condylar protrusion that closely follows the anatomical shape). The patients' patellar tracking was assessed by measuring patellar tilt and displacement during postoperative follow-up. Furthermore, postoperative knee function and pain were evaluated through range of motion, Knee Society scores (KSS), and Forgotten Joint Score (FJS) to compare the different groups.

FINITE ELEMENT ANALYSIS

Constructing a finite element model of the knee joint of a normal volunteer after total knee arthroplasty using different prostheses for nonpatellar replacement. The three models' von Mises stress distribution heat map, peak contact pressure, and patellar transverse displacement were compared at 30°, 60°, and 90°, respectively.

RESULTS

RADIOGRAPHIC INVESTIGATIONS: A total of 456 knees of 384 patients were investigated at a 3-year follow-up after TKA without patellar resurfacing. There were no significant differences in patellar tracking between the three groups. Patients with all three prostheses demonstrated favorable clinical outcomes at 3 years postoperatively, with no statistically significant differences in knee scores (91.9 vs 92.3 vs 91.8) or range of motion (127.9° vs 128.5° vs 127.7°) between the groups. However, there was a significant difference between Genesis II and Gemini MK II in the Forgotten Joint Score (59.7 vs 62.4). Patients with persistent postoperative anterior knee pain were present in all three groups (16 vs 12 vs 10), but the incidence was not significantly different.

FINITE ELEMENT ANALYSIS

The von Mises stress distribution heat map showed that during flexion, the patellofemoral stresses were mainly concentrated on the lateral side of the prosthesis side, and the contact site gradually shifted downward with increasing flexion angle. At the same time, the peak contact stress of the patellofemoral joint increased with the gradual increase in the flexion angle. Genesis II, with a wider and shallower trochlear groove, showed greater patellofemoral stresses and lateral patellar displacement after TKA without patellar resurfacing. The Gemini MK II with a deeper trochlear groove and slightly protruding lateral condyle is more in line with anatomical design, with smaller patellofemoral joint pressure and better patellar tracking.

CONCLUSIONS

In TKA without patellar resurfacing, a prosthesis with a deeper trochlear groove, a slightly higher lateral femoral condyle, and a more anatomically designed knee that better matches the patellar morphology should be a better choice.

Factors that impact the patellofemoral contact stress in the TKA: a review

Abnormal retro patellar stress is believed to contribute to patellofemoral complications after total knee arthroplasty (TKA), but the causal link between TKA and patellofemoral contact stress remains unclear. By reviewing the relevant studies, we found that both TKA implantation and additional patellar resurfacing increase retro patellar pressure. The rotation and size of the femoral component, thickness and position of the patellar component, installation of the tibial component, prosthesis design and soft tissue balance further influence patellofemoral stress. Specific measures can be applied to reduce stress, including the installation of the femoral prosthesis with an appropriate external rotation angle, placing the tibial component at a more posterior position and the patellar button at a more medial position, avoiding over-sized femoral and patellar components, selecting posterior-stabilized design rather than cruciate-retaining design, using gender-specific prosthesis or mobile-bearing TKA system, and releasing the lateral retinaculum or performing partial lateral facetectomy. Despite these measures, the principle of individualization should be followed to optimize the patellofemoral biomechanics.

Numerical investigation of patellar instability during knee flexion due to an unbalanced medial retinaculum loading effect

Background and aim

Healthy patellofemoral (PF) joint mechanics are critical to optimal knee joint function. Patella plays a vital role in distributing quadriceps load during the knee extension. Patellar tracking, not physiological tracking, causes an increase of strains in PF ligaments, peaks of localized stress of soft tissues and articular cartilage and bony parts, and knee pain; these problems lead to complications such as bone abnormalities and osteoarthritis. This research aimed to develop a Finite Element (FE) model to evaluate patellar instability due to the medial retinaculum asymmetric loading effect.

Methods

A numerical model of the knee was obtained by matching nuclear magnetic resonance (MRI) for soft tissues and computerized tomography (CT) for bones, carried on a normal adult. Loading setup was chosen by using literature data. The intensity of the muscle forces was calculated by a static optimization taking into account ground reaction and knee flexion/extension during walking. The effect of patellar instability was obtained by gradually unbalancing this symmetry, one side was unloaded till 90 N, and the other loaded till 110 N.

Results

Unbalanced forces of 10 N acting on the retinaculum alone can produce a real difference in displacements of about 7 mm, and an increment of about 44% on patellar contact forces.

Conclusion

This research demonstrated how an unbalanced forces acting on the retinaculum can produce significant patellar instability. Patellar instability starts at 25-30° of the knee flexion angle but tends to appear at 15° when the unbalanced muscular loading conditions are acting.

Tibial sagittal and rotational alignment reduce patellofemoral stresses in posterior stabilized total knee arthroplasty

Patellofemoral joint complications remain an important issue in total knee arthroplasty. We compared the patellofemoral contact status between cruciate-retaining and posterior-stabilized designs with varying degrees of tibial sagittal and rotational alignment using a computer simulation to ensure proper alignments in total knee arthroplasty. Knee kinematics, patellofemoral contact force and quadriceps force were computed using a musculoskeletal modeling program (LifeMOD/KneeSIM 2010; LifeModeler, Inc., San Clemente, California) during a weight-bearing deep knee bend. Two different posterior tibial slope (PTS)s (3° and 7°) and five different tibial tray rotational alignments (neutral, internal 5° and 10°, and external 5° and 10°) were simulated. Patellofemoral contact area and stresses were next computed using finite element analysis. The patellofemoral contact force for the posterior-stabilized design was substantially lower than the cruciate-retaining design after post-cam contact because of increasing femoral roll-back. Neutral rotational alignment of the tibial component resulted in smaller differences in patellofemoral contact stresses between cruciate-retaining and posterior-stabilized designs for PTSs of 3° or 7°. However, the patellar contact stresses in the cruciate-retaining design were greater than those in posterior-stabilized design at 120° of knee flexion with PTS of 3° combined with internal rotation of the tibial component. Our study provides biomechanical evidence implicating lower PTSs combined with internal malrotation of the tibial component and the resultant increase in patellofemoral stresses as a potential source of anterior knee pain in cruciate-retaining design.

Lateral Patellofemoral Ligament Reconstruction With Semitendinosus Allograft in the Setting of Previous Lateral Release

The lateral patellofemoral ligament acts to resist medial displacement of the patella. When medial subluxation occurs, it usually has an iatrogenic cause such as prior lateral release, an over-tightened medial patellofemoral ligament reconstruction, or detachment of the vastus lateralis from the patella. The justification for lateral retinacular release has historically been to address extensor mechanism issues such as imbalance of the mechanism due to increased retinacular tension. We present a Technical Note on the treatment of chronic medial patellar instability due to a previous lateral retinacular release using a soft-tissue reconstruction approach with a semitendinosus allograft.

Kinematically Aligned Total Knee Arthroplasty Did Not Show Superior Patient-Reported Outcome Measures: An Updated Meta-analysis of Randomized Controlled Trials with at Least 2-Year Follow-up

Kinematically aligned total knee arthroplasty (KATKA) was developed to improve the anatomical alignment of knee prostheses, assisting in restoring the native alignment of the knee and promoting physiological kinematics. Early clinical results were encouraging, showing better functional outcomes than with mechanically aligned total knee arthroplasty (MATKA). However, there have been concerns about implant survival, and follow-up at 10 years or more has not been reported. In addition, randomized controlled trials (RCTs) comparing KATKA with MATKA have reported inconsistent results. The current meta-analysis of RCTs with a minimum of 2 years of follow-up investigated the clinical and radiological differences between KATKA and MATKA. A systematic review of the English language literature resulted in the inclusion of four RCTs. The meta-analysis found no significant difference in any of the following parameters: postoperative range of motion for flexion (mean difference for KATKA - MATKA [MD], 1.7 degrees; 95% confidence interval [CI], -1.4 to 4.8 degrees; p = 0.29) and extension (MD, 0.10 degrees; 95% CI, -0.99 to 1.2 degrees; p = 0.86); Oxford Knee Score (MD, 0.10 points; 95% CI, -1.5 to 1.7 points; p = 0.90); Knee Society Score (MD, 1.6 points; 95% CI, -2.8 to 6.0 points; p = 0.49); and Knee Function Score (MD, 1.4 points; 95% CI, -4.9 to 7.8 points; p = 0.66). In addition, there was no significant difference between KATKA and MATKA in the rate of complications requiring reoperation or revision surgery (odds ratio, 1.01; 95% CI, 0.25-4.09; p = 0.99) or in the length of hospital stay (MD, 1.0 days; 95% CI, -0.2 to 2.2 days; p = 0.092). KATKA did not increase the number of patients with poor clinical results due to implant position, particularly for varus placement of the tibial component. In this meta-analysis based on four RCTs with a minimum of 2 years of follow-up, KATKA were only relevant to cruciate retaining TKA and could not be extrapolated to posterior stabilized TKA. Patient-reported outcome measures with KATKA were not superior to those with MATKA.

Intraoperative analysis of patellofemoral joint morphology before and after total knee arthroplasty

Background

Patellofemoral problems after total knee arthroplast (TKA) are frequent and often associated with a change in the geometry of the trochlear groove.

Objective

The present study aimed to analyze the feasibility of intraoperative examination of the patellofemoral joint geometry before and after the implantation of bicondylar total knee replacements without exposing the patient to radiation.

Material and methods

The patellofemoral joint morphology geometries of 33 patients before and after implantation of a bicondylar total knee replacement was intraoperatively analyzed using a digital scanning method. Femoral surface geometries were extracted from intraoperatively recorded tactile scanning data using an in-house algorithm. The geometries were then characterized by sulcus height, medial femoral condyle height and lateral femoral condyle height.

Results

Our preliminary results show that these key geometric parameters are only partially restored after TKA leading to a distinctly different shaped profile of the anterior distal femur. Maximum and minimum mean differences in sulcus height, medial femoral condyle height, and lateral femoral condyle height before and after surgery were 2.00 mm/−3.06 mm, 2.51 mm/−6.25 mm and 2.74 mm/−3.58 mm, respectively.

Conclusion

A new method for intraoperative analysis of the patellofemoral joint morphology before and after TKA without radiation exposure was developed and utilized. Even with the use of modern total knee designs, the patellofemoral articulation is considerably changed postoperatively as quantified by the key parameters of sulcus height, medial femoral condyle height, and lateral femoral condyle height. This may result in altered knee biomechanics and might explain persistent patellofemoral disorders, which are often reported by patients after TKA.

Lateral Patellar Facetectomy Reduces the Incidence of Anterior Knee Pain in Patellar Resurfaced Total Knee Arthroplasty

Lateral patellar facet impingement (LPFI) can cause anterior knee pain (AKP) after patellar resurfaced total knee arthroplasty (TKA). Recently, lateral patellar facetectomy (LPF), which has been used for LPFI, has been performed during primary TKA, providing good clinical outcomes. However, the effect of LPF on AKP in primary patellar resurfaced TKA has not been sufficiently studied. The purpose of this study was to examine the effect of LPF on the development of AKP in patellar resurfaced TKAs with minimum follow-up of 3 years. This retrospective cohort study included 84 knees of 66 consecutive patients who underwent patellar resurfaced TKA between April 2007 and November 2014 in our hospital. The subjects were divided into two groups: TKA with LPF (LPF group; 47 knees) and TKA without LPF (no-LPF group; 37 knees). Postoperative AKP, the primary outcome, the Japanese Orthopaedic Association (JOA) score, and range of motion were investigated at the final visit and compared between the two groups. Six knees (16.2%) had AKP in the no-LPF group, whereas none of the knees had AKP in the LPF group at the final visit. The incidence of AKP was significantly lower in the LPF group (p = 0.004). The postoperative JOA score and flexion angle were significantly higher in the LPF group than in the no-LPF group. LPF correlated with less incidence of postoperative AKP and improved the JOA score and knee flexion angle. In patellar resurfaced TKA, LPF may be considered an additional maneuver to avoid postoperative AKP.

The lack of retropatellar resurfacing at index surgery is significantly associated with failure in patients following patellofemoral inlay arthroplasty: a multi-center study of more than 260 patients

PURPOSE

To evaluate the clinical outcomes of patients with a minimum 2-year follow-up following contemporary patellofemoral inlay arthroplasty (PFIA) and to identify potential risk factors for failure in a multi-center study.

METHODS

All patients who underwent implantation of PFIA between 09/2009 and 11/2016 at 11 specialized orthopedic referral centers were enrolled in the study and were evaluated retrospectively at a minimum 2-year follow-up. Clinical outcomes included the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) score, the Knee Injury and Osteoarthritis Outcome Score (KOOS), the Tegner Scale, the visual analogue scale (VAS) for pain, and subjective patient satisfaction. Pre- and perioperative risk factors were compared among failures and non-failures to determine potential risk factors.

RESULTS

A total of 263 patients (85% follow-up rate) could be enrolled. The mean age at the time of index surgery was 49 ± 12 years with a mean postoperative follow-up of 45 ± 18 months. The overall failure rate was 11% (28 patients), of which 18% (5 patients) were patients with patella resurfacing at index surgery and 82% (23 patients) were patients without initial patella resurfacing. At final follow-up, 93% of the patients who did not fail were satisfied with the procedure with a mean transformed WOMAC Score of 84.5 ± 14.5 points, a mean KOOS Score of 73.3 ± 17.1 points, a mean Tegner Score of 3.4 ± 1.4 points and a mean VAS pain of 2.4 ± 2.0 points. An increased BMI was significantly correlated with a worse postoperative outcome. Concomitant procedures addressing patellofemoral instability or malalignment, the lack of patellofemoral resurfacing at the index surgery and a high BMI were significantly correlated with failure in our patient cohort.

CONCLUSION

Patellofemoral inlay arthroplasty shows high patient satisfaction with good functional outcomes at short-term follow-up and thus can be considered a viable treatment option in young patients suffering from isolated patellofemoral arthritis. Patellar resurfacing at index surgery is recommended to decrease the risk of failure.

LEVEL OF EVIDENCE

Retrospective case series, Level IV.

Can TKA outcomes be predicted with computational simulation? Generation of a patient specific planning tool

BACKGROUND

Computer simulations of knee movement allow Total Knee Arthroplasty (TKA) dynamic outcomes to be studied. This study aims to build a model predicting patient reported outcome from a simulation of post-operative TKA joint dynamics.

METHODS

Landmark localisation was performed on 239 segmented pre-operative computerized tomography (CT) scans to capture patient specific soft tissue attachments. The pre-operative bones and 3D implant files were registered to post-operative CT scans following TKA. Each post-operative knee was simulated undergoing a deep knee bend with assumed ligament balancing of the extension space. The kinematic results from this simulation were used in a Multivariate Adaptive Regression Spline algorithm, predicting attainment of a Patient Acceptable Symptom State (PASS) score in captured 12 month post-operative Knee Injury and Osteoarthritis Outcome Scores (KOOS). An independent series of 250 patients was evaluated by the predictive model to assess how the predictive model behaved in a pre-operative planning context.

RESULTS

The generated predictive algorithm, called the Dynamic Knee Score (DKS) contained features, in order of significance, related to tibio-femoral force, patello-femoral motion and tibio-femoral motion. Area Under the Curve for predicting attainment of the PASS KOOS Score was 0.64. The predictive model produced a bimodal spread of predictions, reflecting a tendency to either strongly prefer one alignment plan over another or be ambivalent.

CONCLUSION

A predictive algorithm relating patient reported outcome to the outputs of a computational simulation of a deep knee bend has been derived (the DKS). Simulation outcomes related to tibio-femoral balance had the highest correlation with patient reported outcome.

Comparison of Functional Outcomes, Femoral Rollback and Sagittal Stability of Anterior-Stabilized Versus Posterior-Stabilized Total Knee Arthroplasty: A Systematic Review and Meta-analysis of Randomized Controlled Trials

PURPOSE

Total knee arthroplasty (TKA) has improved leaps and bounds in terms of design to improve clinical outcomes and achieve better rehabilitation of the patients. Ultra-congruent inserts (UC) were designed to replace the need for posterior stabilized (PS) implants. The purpose of this review was to evaluate clinical outcomes, femoral rollback, functional scores, range of motion, sagittal laxity, complication rates, and isokinetic performance between UC and PS TKA among RCTs.

METHODS

Electronic databases such as PubMed, Scopus, opengrey, and Cochrane were searched from date of inception up to mid-April 2021, and meta-analysis was performed following PRISMA guidelines. This study analyzed outcomes, femoral rollback, tibial sagittal laxity and isokinetic performance.

RESULTS

Ten RCTs identified 852 knees, of which 420 underwent UC TKAs and 432 underwent PS TKA. Compared to UC TKA, a significantly better sagittal stability (p = 0.17) and femoral rollback (p < 0.00001) in PS TKAs was noted, although no statistically significant difference was found in the assessment of the range of motion (p = 0.19) and functional scores. Both the groups had similar isokinetic performance with extensor torque (p = 0.97) and flexor torque (p = 0.37).

CONCLUSIONS

We conclude with the current meta-analysis that there are no added benefits for UC over PS inserts and these inserts have a higher sagittal laxity and less femoral roll back in cruciate sacrificing UC knee. But since there are no long-term wear data, UC inserts with CS technique should be used cautiously and may be used only when the PCL cannot be balanced adequately. There is no evidence or only a few to support the superiority of the AS TKA in terms of clinical outcomes or isokinetic performance or femoral external rotation over PS TKA.

LEVEL OF EVIDENCE

Level I, Systematic review and meta-analysis of RCTs.

Management of the Patella During Total Knee Arthroplasty

»

The optimal management of the patella during total knee arthroplasty (TKA) remains a controversial topic with no consensus.

»

Patellar management techniques during TKA include patellar retention or resurfacing with or without patellaplasty, as well as circumferential denervation and partial lateral facetectomy (PLF).

»

Special considerations such as patient age, etiology of disease, implant design, and surgeon preference should be accounted for when determining optimal management.

»

We recommend that most patellae be circumferentially denervated, regardless of whether they are resurfaced, as the potential benefits outweigh the small associated risks.

»

Evidence demonstrates improved functional outcomes with the addition of PLF to nonresurfaced patellae. There is currently a paucity of evidence of this technique with respect to resurfaced patellae.

»

Patellar resurfacing adds additional costs and health-care resources that should be considered in the decision-making process.

Anterior prominence of the femoral condyle varies among prosthesis designs and surgical techniques in total knee arthroplasty

BACKGROUND

Patellofemoral overstuffing after total knee arthroplasty (TKA) can cause limited range of motion and anterior knee pain. This study compared anterior prominence of femoral components among different prothesis designs in surgical simulation models utilizing the anterior reference (AR) and posterior reference (PR) techniques.

METHODS

Surgical simulations were performed using on a three-dimensional planning system preoperative computed tomography data of consecutive 30 patients with knee osteoarthritis scheduled to undergo TKA. Four implant models were used: Attune, Persona, Journey II, and Legion. Rotational alignment was set parallel to the transepicondylar axis and size was selected based on the absence of notch formation in the femoral anterior cortex and the best fit with the shape of the medial posterior femoral condyle. For each combination of surgical technique (AR or PR method) and implant model, measurements were taken of the maximum medial, central, and lateral prominence of the implant from the anterior femoral cortex.

RESULTS

Using either the AR or PR method, the medial and central prominences were significantly lower with Journey II than with the other models. The lateral prominence was the lowest with Attune in the AR method. The AR method was associated with significantly less prominence compared with the PR method, regardless of implant model.

CONCLUSIONS

The degree of anterior prominence of the femoral implant is affected by the implant design when the AR method is used. The PR method is associated with greater anterior prominence compared with the AR method, and the pitch size is an additional factor in the PR method. Surgeons should be familiar with implant designs, including the thickness of the anterior flange and the available size selections.

Influence of Patellar Morphology Classified by Wiberg Classification on Knee Joint Function and Patellofemoral Tracking After Total Knee Arthroplasty Without Patellar Resurfacing

BACKGROUND

To evaluate the influence of patellar morphology on knee joint function and patellofemoral tracking in patients with primary osteoarthritis after total knee arthroplasty (TKA) without patellar resurfacing.

METHODS

We performed a retrospective study of 156 patients with primary osteoarthritis who underwent TKA without patellar resurfacing from April 2018 to July 2019. As per Wiberg classification, patients were divided into Wiberg type I (group A, n = 38), II (group B, n = 88), and III (group C, n = 30) groups. The clinical data, postoperative follow-up data, and radiological data between three groups were compared.

RESULTS

There was no statistically significant difference in the HSS score and Feller score between the three groups before surgery and at each follow-up point after surgery (P > .05). At the last follow-up, there were no significant differences in the height and relative thickness of the patella between the three groups (P > .05). However, the incidence of anterior knee pain was significantly higher in group C than in the group B (P < .05). The patellar tilt angle was significantly larger in group C than in the groups A and B (both P < .05). The patellar facet angle was significantly larger in group A than in group B and C, which was also significantly larger in group B than in group C (both P < .05).

CONCLUSION

Patients with three different morphologic types of the patella both exhibited improved knee joint function after TKA, however, patients with Wiberg type Ⅲ patella were more prone to have poor patellofemoral tracking and anterior knee pain after surgery.

[Biomechanical research on effects of pseudo-patella baja on stress of patellofemoral joint after total knee arthroplasty]

Objective

To investigate biomechanical effects of pseudo-patella baja on stress of patellofemoral joint after total knee arthroplasty (TKA) by using finite element analysis (FEA).

Methods

A series of CT and MRI of the left knee joint of two healthy volunteers and three-dimensional (3D) scanned data of TKA prosthesis were taken, and the 3D models of knee before and after TKA were established. The finite element model of pseudo-patella baja, normal patella, and alta patella after TKA were constructed by Insall-Salvafi (IS) ratio and Blackburne-Peel (BP) ratio. The load was applied along the direction of quadriceps femoris. After testing the validity of the finite element model, the high contact stress of patellofemoral joint was measured on the von Mise stress nephogram of pseudo-patella baja, normal patella, and alta patella after TKA when the knee flexion was 30°, 60°, and 90°. The average contact area was calculated according to two volunteers' data.

Results

On the finite element model of the normal patella after TKA with knee flexion 30°, 475 N pressure was applied along the direction of quadriceps femoris. The contact stress of patellofemoral joint was (1.29±0.41) MPa, which was similar to the results reported previously. The finite element model was valid. The von Mise stress nephogram showed that the stress mainly focused on the medial patellofemoral articular surface during knee flexion, and the contact point gradually moved up with the knee flexion deepened. The stress on the medial and lateral patellofemoral articular surface increased with the knee flexion deepened but decreased with the increase of patellar height. The effects of patellar height and knee flexion on the high contact stress of patellofemoral joint were similar among the finite element models after TKA based on the data of two volunteers. The high contact stress of patellofemoral joint increased with the knee flexion deepened in the same patellar height models ( P<0.05), but decreased with the increase of patellar height in the same knee flexion models ( P<0.05). The high contact stress of patellofemoral joint of pseudo-patella baja model was significantly higher than normal and alta patella models ( P<0.05). The average contact area of patellofemoral joint of pseudo-patella baja was bigger than normal and alta patella models with the knee flexion deepened.

Conclusion

The pseudo-patella baja after TKA has an important effect on the biomechanics of patellofemoral joint. Reserving the joint line and avoiding the occurrence of pseudo-patella baja can decrease the risk of anterior knee pain, patellar arthritis, and other complications caused by the increasing of contact stress of patellofemoral joint.

Influence of Patella thickness on Patellofemoral pressure in total knee Arthroplasty

BACKGROUND

Patellofemoral complications are one of the major issues after total knee arthroplasty (TKA). Excessive patellofemoral joint pressure is associated with complications after TKA surgery, and the amount of patellar osteotomy has a direct effect on patellofemoral joint pressure. The purpose of this study was to evaluate the influence of patella thickness on patellofemoral pressure in TKA.

METHODS

Five freshly frozen cadavers were operated with a custom-made Stryker posterior stabilizing type knee joint prosthesis. Patellofemoral joint pressure was measured using a pressure sensor, with the knee joint flexed from 90 to 110 degrees, and with patellar thickness of - 2 mm to + 4 mm.

RESULTS

Increasing or decreasing patellar thickness significantly increased or decreased patellofemoral pressure. Regarding knee flexion angle, patellofemoral pressure increased with increasing patellar thickness at all flexion angles, but the pressure increase was greatest at 90 degrees of knee flexion and smallest at 110 degrees.

CONCLUSIONS

The amount of patellar osteotomy influences the patellofemoral pressure. Surgeons should avoid increasing patella thickness, since the resulting increased patellofemoral pressure may reduce knee joint function.

Biomechanical Study of Patellar Component Fixation with Varying Degrees of Bone Loss

BACKGROUND

The decision as to whether or not to resurface the patella in revision total knee arthroplasty (TKA) is affected by the amount of patellar bone stock remaining; however, the impact of the cancellous bone status on patellar component fixation has not been studied. Therefore, we conducted a biomechanical study of patellar component fixation with varying degrees of cancellous bone loss.

METHODS

Sixty pairs of cadaveric patellae were randomly assigned between 3 groups and prepared in similar manner to a TKA with the standard 3-hole configuration. A control patella and an experimental patella were designated in each pair. To simulate bone loss in the experimental patellae, 1, 2, and 3 of the standard drill holes were uniformly enlarged to 12 mm in group 1, group 2, and group 3, respectively. Afterward, an all-polyethylene patellar component was cemented to each patella, as done intraoperatively. Patellar components were then sheared off using a materials testing system. The resulting mean offset yield force was analyzed within each group using paired t-tests.

RESULTS

The mean offset yield force for the control patellae was greater than the experimental patellae in group 1. In groups 2 and 3, the experimental patellae produced a greater mean offset yield force than the control patellae. Comparison within each group did not demonstrate a statistically significant difference.

CONCLUSION

Bone loss with enlargement of the patellar fixation holes, as is frequently seen in revision TKA, with holes up to 12 mm, does not significantly decrease patellar component fixation shear strength in this biomechanical cadaveric study.

Improving radiographic patello-femoral tracking in total knee arthroplasty with the use of a flexion spacer: a case-control study

PURPOSE

The purpose of this study was to compare the effectiveness of a flexion spacer in the clinical and radiological outcomes of patients who underwent total knee arthroplasty (TKA) and to compare these patients to a group of patients subjected to the same type of surgery but without the use of a flexion spacer. It was hypothesized that patients who underwent TKA using a flexion spacer would have better clinical and radiological outcomes than those without a flexion spacer in both short- and medium-term follow-ups.

METHODS

A consecutive series of patients undergoing TKA were included, yielding 20 patients in the study group. The control group was identified from the consultant database of the senior author, yielding 21 patients who underwent the same operation. All 41 patients received a Vanguard Knee System (Zimmer-Biomet, Warsaw, Indiana, USA). Cases were defined as those patients who had undergone TKA using a flexion spacer device for gap balancing; controls were defined as patients who had undergone TKA without the support of a flexion spacer device. Patients were clinically and radiographically evaluated at two consecutive follow-ups: T1-13.1 ± 1.3 months and T2-108 ± 6 months. Clinical evaluation was performed using the Knee Society Scoring System and the Western Ontario, McMaster Universities Osteoarthritis Index score. Radiographic evaluation included the femoral angle (α), the tibial angle (β), the sagittal femoral (γ) angle and the tibial slope (δ). Furthermore, the lateral patellofemoral angle (LPFA) and the Caton-Deschamps index were evaluated.

RESULTS

No statistically significant clinical differences were found between the two groups at T1 and T2; moreover, the clinical outcomes of the two groups were stable between the two follow-ups, with no significant improvement or worsening. Radiographic evaluation showed no difference in the two groups between T1 and T2; the only significant radiographic difference between the two groups concerned the LPFA (both at 30° and 60°) at each follow-up, which was significantly greater in cases than in controls (p = 0.001).

CONCLUSIONS

The current study demonstrates that the use of a flexion spacer significantly improves radiographic patello-femoral tracking, although no significant clinical differences were found between the two groups.

LEVEL OF EVIDENCE

Case-control study, level III.

Early Patellofemoral Function of Medial Pivot Prostheses Compared with Posterior-Stabilized Prostheses for Unilateral Total Knee Arthroplasty

Objective

To systematically evaluate the patellofemoral joint design of medial pivot prosthesis, which incorporates a variety of “patella‐friendly” design features, by comparing clinical and radiographic results with another prosthesis.

Methods

All consecutive patients who underwent unilateral total knee arthroplasty (TKA) with medial pivot prosthesis (Group MP, 126 cases) between September 2016 and April 2018 were enrolled in this retrospective study. For each patient reviewed, a control patient was matched, according to age, gender, side, body mass index (BMI), preoperative range of motion (ROM), and operating period, who had received primary unilateral TKA with a conventional posterior‐stabilized prosthesis at the same period as the study group (Group PS, 126 cases). All patients underwent at least 1‐year follow‐up. At the preoperative and final follow‐up periods, data on the Knee Society Score (KSS) score, WOMAC score, Kujala score, and ROM were collected. Merchant views were taken with the knee flexion at 30°, 60°, and 90° to measure patella shift and tilt. Preoperative posterior condylar angle (PCA) was also measured. Postoperative complications, including anterior knee pain, maltracking, patellar clunk or crepitus (PCC), were evaluated.

Results

There were no significant differences in the demographics or clinical characteristics between the two groups. No statistically significant difference was identified in the KSS total score, including knee score and function score, or in the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) score between the two groups after the operation. We found statistically significant differences in the postoperative Kujala scores and the ROMs between the two groups. The mean Kujala score in group MP was better than in group PS (MP 77.16 ± 3.80 vs PS 75.97 ± 4.06, P < 0.05), while the ROM in group PS was significantly higher than in group MP (MP 122.24° ± 4.45° vs PS 123.78° ± 6.05°, P < 0.05). Simultaneously, the preoperative/postoperative Kujala score improvement in group MP was observed to be significantly larger than in group PS (MP 27.82 ± 5.31 vs PS 26.17 ± 4.89, P < 0.05), but the average ROM improvement in group PS was significantly greater than in group MP (MP 19.00° ±9.90° vs PS 21.57° ± 9.62°). In the 90° Merchant view, the mean patella tilt of group MP was statistically smaller than that of group PS (MP 4.21° ± 1.62° vs PS 4.74° ± 1.95°, P < 0.05), and the average patella tilt change in group MP was significantly greater than in group PS (MP –3.8° ± 1.43° vs PS –3.23° ± 1.33°, P < 0.05). Preoperative PCA did not show significant differences between the two groups. Two cases of PCC and three cases of anterior knee pain were noted in group MP, and nine cases and six cases, respectively, were observed in group PS. The incidence of PCC was significantly lower in group MP (1.6% vs 7.1%, P < 0.05). There was no significant difference in follow‐up time between the two groups.

Conclusion

The medial pivot prosthesis could achieve satisfactory outcomes with better patellofemoral performance attributed to its “patella‐friendly” design characteristics compared to the conventional posterior‐stabilized prosthesis.

Reliable improvements in participation in low-impact sports following implantation of a patellofemoral inlay arthroplasty at mid-term follow-up

PURPOSE

The aim of this study was, to investigate the rate of return to sports (RTS) and physical activity after implantation of PFIA and to identify factors predictive of improved postoperative sporting ability.

METHODS

Sixty-two patients with a mean age of 46 ± 11 years, who underwent implantation of PFIA at the senior authors' institution, were enrolled. They were prospectively evaluated preoperatively and at a minimum of 2 years postoperatively with a mean follow-up of 60 ± 25 months. Clinical outcomes, return to sports and activity, type of sport or activity, subjective satisfaction, and frequency were evaluated by questionnaire.

RESULTS

The transformed overall Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) score improved from 67 ± 16 to 77 ± 19 (p = 0.003), Tegner activity scale results improved from 3 ± 2 points to 4 ± 1 points (p < 0.001), and scores on the visual analog scale (VAS) pain scale decreased from 6 ± 2 points to 3 ± 2 points (p < 0.001). The sports frequency increased from 1 ± 2 sessions to 2 ± 1 sessions per week (p = 0.001). Ninety-four percent of the patients who did not fail could return to the same or higher level of sports, with 74% of the patients reporting an improved ability to perform sports. No preoperative factors could be detected to significantly influence RTS after surgery.

CONCLUSIONS

PFIA is a valid treatment option for the active patient with end-stage isolated patellofemoral OA. Reliable improvements in knee function, pain, and participation in low-impact sports were found.

LEVEL OF EVIDENCE

IV.

The tibial cut influences the patellofemoral knee kinematics and pressure distribution in total knee arthroplasty with constitutional varus alignment

PURPOSE

The current literature suggests that kinematic total knee arthroplasty (kTKA) may be associated with better outcome scores in patients with constitutional varus alignment. The underlying patellofemoral kinematic changes (patella tilting and patella tracking) and patellofemoral pressure distribution have not yet been described. The present study compared the effects of different tibial cuts, as used in kTKA, on patellofemoral knee kinematics and the pressure distribution, in addition to comparisons with the natural constitutional varus knee.

METHODS

Seven cadaveric knee joints with constitutional varus alignment were examined in the native state and after 0°, 3°, or 6° tibial cut cruciate-retaining (CR)-TKA using an established knee joint simulator. The effects on patella rotation/patella tilting, patellofemoral pressure, and patellofemoral length ratios (= patella tracking) were determined. In addition, the natural knee joint and different tibial cuts in CR-TKA were compared (Student's t test).

RESULTS

In the patellofemoral joint, 6° CR-TKA was associated with the greatest similarity with the natural constitutional varus knee. By contrast, knees subjected to 0° CR-TKA exhibited the largest deviations of patellar kinematics. The smallest difference compared with the natural knee joint concerning patella tilting was found for 6° CR-TKA (mean 0.4°, p < 0.001), and the largest difference was noted for 0° CR-TKA (mean 1.7°, p < 0.001). Concerning patellofemoral pressure, 6° CR-TKA resulted in outcomes most similar to the natural knee joint, featuring a mean difference of 3 MPa. The largest difference from the natural knee joint was identified for 0° CR-TKA, with an average difference of 8.1 MPa (p < 0.001; total mean 17.7 MPa). Meanwhile, 3° and 6° CR-TKA induced medialization of the patella, with the latter inducing the largest medialization value of 4.5 mm at 90° flexion.

CONCLUSIONS

The improved outcome parameters in kTKA described in the literature could be attributable to the similar kinematics of the patellofemoral joint relative to the normal state. The current study confirmed the similar kinematics between the native constitutional varus knee joint and knee joints subjected to 3° or 6° CR-TKA (patellofemoral rotation/patella tilting and patella pressure). Conversely, there was pronounced medialization of the patella following 6° CR-TKA. Patella pressure and patella tilting are described in the literature as possible causes of anterior knee pain after TKA, whereas medialization of the patella, which is also influenced by other causes, might play a subordinate role.

LEVEL OF EVIDENCE

V, Biomechanical study.

Anterior-stabilized TKA is inferior to posterior-stabilized TKA in terms of postoperative posterior stability and knee flexion in osteoarthritic knees: a prospective randomized controlled trial with bilateral TKA

PURPOSE

To determine whether knee stability, range of motion (ROM) and clinical scores differ between anterior-stabilized (AS) and posterior-stabilized (PS) total knee arthroplasty (TKA).

METHODS

This prospective randomized controlled trial included 34 patients with severe bilateral knee osteoarthritis who underwent bilateral TKA between June 2010 and July 2011 using AS and PS designs of a single-implant system. AS TKA with ultracongruent inserts was performed in one knee and PS TKA with a cam-post mechanism was performed in the other knee in each patient. Clinical and radiological data from a mean follow-up period of 5 years, including ROM, clinical scores, peak knee torque determined by isokinetic test, knee joint laxity determined by Telos stress views, tourniquet time and subjects' preference were analyzed.

RESULTS

The mean postoperative knee flexion angle did not differ between groups until 1 year. Beginning 2 years postoperatively, the knee flexion angle decreased slightly in the AS group and was smaller than that in the PS group (p = 0.004). The mean Knee Society knee score was higher in the PS group than in the AS group after 2 years. The quadriceps strength did not differ between groups. The mean posterior laxity after TKA was 6-8 mm greater in the AS group than in the PS group. No radiological loosening was observed in either group. More subjects preferred PS knees to AS knees. However, this difference was not significant.

CONCLUSION

AS primary TKA was inferior to PS TKA in terms of posterior knee stability, postoperative knee flexion and clinical scores after 2 years.

LEVEL OF EVIDENCE

Therapeutic study, Level 1.

[Effect of surgeon's handedness on distribution of prosthesis during primary total knee arthroplasty]

OBJECTIVE

To evaluate the effect of the surgeon's handedness on the distribution of prosthesis during primary total knee arthroplasty (TKA).

METHODS

A retrospective analysis was performed on 86 patients (100 knees) with primary TKA completed by the same right-handed surgeon between December 2016 and December 2018, including 72 cases of single knee and 14 of bilateral knees. The patients were divided into dominant group (right side) and non-dominant group (left side) according to the operating position of the surgeon and each group had 50 knees. There was no significant difference in gender, age, body mass index, disease duration, clinical diagnosis, preoperative Hospital for Special Surgery (HSS) score, and other general data between the two groups ( P>0.05). The operation time and complications were recorded in both groups. The function of knee was evaluated by HSS score. Hip-knee-ankle angle (HKA), mechanical lateral distal femoral angle (mLDFA), and mechanical medial proximal tibial angle (mMPTA) were measured by using X-ray film of full-length lower extremity before TKA and at 2 weeks after TKA that were used to evaluate the coronal position of the prosthesis. Posterior distal femoral angle (PDFA) and posterior proximal tibial angle (PPTA) were measured by using lateral X-ray films at 3 months after operation that were used to evaluate the sagittal position of the prosthesis.

RESULTS

There was no significant difference in operation time between the two groups ( t=-1.128, P=0.262). One case of posterior tibial artery thrombosis occurred in the dominant group, and 1 case of poor healing of the incision occurred in each of the dominant group and the non-dominant group. Patients in both groups were followed up 12-34 months with an average of 22.0 months. The HSS scores at last follow-up were 87.2±4.3 in the dominant group and 86.8±5.0 in the non-dominant group. There was no significant difference between the two groups ( t=0.471, P=0.639). No complications such as periprosthetic infection, prosthetic loosening, or periprosthetic fracture occurred during follow-up. There was no significant difference in the HKA, mLDFA, and mMPTA between the two groups before and after operation ( P>0.05). The differences in the incidence of sagittal femoral prosthesis malposition and PDFA between the two groups were significant ( P<0.05); however, there was no significant difference in the PPTA, the rate of femoral prosthesis distributed in the neutral position, the incidence of over-flexed femoral prosthesis, and the incidence of anterior femoral notch ( P>0.05).

CONCLUSION

The surgeon's handedness is one of the factors affecting the placement of the sagittal femoral prosthesis in primary TKA. The incidence of sagittal femoral prosthesis malposition could increase when the surgeon performs on the non-dominant side.

Comparison of Patient Satisfaction Between Medial Pivot Prostheses and Posterior-Stabilized Prostheses in Total Knee Arthroplasty

OBJECTIVE

To compare medial pivot (MP) prostheses to two types of posterior-stabilized (PS) prostheses (NexGen and NRG) in terms of patient satisfaction, causes of dissatisfaction, and risk factors for dissatisfaction after total knee arthroplasty (TKA).

METHODS

A total of 453 patients who underwent primary TKA by one senior surgeon from August 2016 to August 2018 were investigated in a retrospective study, including 121, 219, and 113 patients in the MP, NexGen, and NRG groups, respectively. The mean age and follow-up time of patients were 70.82 ± 7.06 years and 20.64 ± 3.88 months. A survey was designed and responses were collected by telephone, WeChat, and outpatient follow up. Patient satisfaction, causes of dissatisfaction, post-TKA pain on a numeric rating scale (NRS), and range of motion (ROM) were compared among groups, and risk factors were investigated. Patient satisfaction included a five-level satisfaction rating (very satisfied, satisfied, neutral, dissatisfied, or very dissatisfied), with five options for causes of dissatisfaction (persistent pain, limited ROM, knee instability, asthenia, and/or other factors).

RESULTS

Overall, 89.84% of patients were satisfied with the results of primary TKA. There were no significant differences among the three groups regarding the side of the operation, the length of hospitalization in days, or the average follow-up time. Patient satisfaction was similar among the MP (87.38%), NexGen (89.89%), and NRG groups (90.32%). Persistent pain after TKA was the major cause of dissatisfaction (32/40), but no difference in the frequency of this complaint was found among the groups (P = 0.663). The NRS score (P = 0.598) and the ROM (P = 0.959) of the MP group were not significantly different from those of the NexGen and NRG groups. Gender, length of hospitalization, and follow-up time were all uncorrelated with patient satisfaction, but age showed a very weak correlation with patient satisfaction (r = 0.110, P = 0.033). Moreover, the NRS score (r = 0.459, P < 0.000) and the ROM (r = -0.175, P = 0.001) were significantly correlated with patient dissatisfaction. The odds ratio of dissatisfaction was 6.37 (P < 0.000) in patients with moderate to severe pain (NRS ≥ 3) compared to patients with mild pain (NRS < 3).

CONCLUSION

Patient satisfaction and function were not found to be higher in the MP group than in the two PS groups, and persistent pain was the major cause of and an important risk factor for patient dissatisfaction.

Sagittal alignment of the cemented femoral component in revision total knee arthroplasty influences the anterior and posterior condylar offset: Stem length does not affect these variables

BACKGROUND

The position of the femoral component can influence knee kinematics by altering the posterior (PCO) and anterior condylar offset (ACO). The primary aim of this study was to assess whether the length of the cemented stem influences the sagittal position of the femoral component after revision total knee arthroplasty (rTKA). The secondary aim was to determine the influence of the sagittal position on PCO and ACO.

METHODS

There were 172 consecutive patients over a seven-year period that underwent rTKA with a cemented semi-constrained prosthesis. The 172 patients were separated into two groups: 115 with short stems (50 mm) and 57 with longer stems (100 or 150 mm). Using rotationally acceptable lateral radiographs, the degree of flexion(+)/extension(-) of the femoral components, PCO, and ACO were measured.

RESULTS

There was no significant difference (p > 0.25) between the two groups for sagittal position, PCO, or ACO. The average flexion of the femoral component with short stems was 2.2 ± 4.1° and 2.2 ± 3.4° for long stems (difference = 0.0, 95% confidence intervals (CI) -1.3 to 1.2). The average PCO ratio was 1.02 ± 0.15 for short stems and 0.99 ± 0.17 for long stems (difference = 0.03, 95% CI -0.02 to 0.08). The average ACO ratio was at 0.07 ± 0.08 for short stems and 0.08 ± 0.08 for long stems (difference = 0.01, 95% CI -0.01 to 0.04). There was a significant correlation between sagittal alignment of the femoral component and PCO (flexion increased PCO, r = 0.39, p < 0.0001) and ACO (flexion decreased ACO, r = -0.34, p < 0.0001).

CONCLUSIONS

Cemented stem length does not influence the position of femoral component in the sagittal axis, PCO, or ACO. Surgical technique and sizing of the femoral component may be more predictive.

Does Preoperative tibial tuberosity: Trochlear groove distance effect on postoperative patellar instability in the patients with knee arthroplasty due to medium-advanced knee osteoarthritis?

Objectives: Determining tibial tubercle-trochlear groove distance range as measured before the operation in the patients to whom total knee prosthesis will be applied due to mid to advanced level of osteoarthritic and seeing the post-operative variations in tibial tubercle-trochlear groove distance and evaluating whether it has any impact on the patellofemoral instability that might develop after the operation. 46 knees planned to be applied total knee prosthesis due to mid-advanced level of osteoarthritic were examined. Methods: In the preoperative and postoperative magnetic resonance images MRI routinely taken, tibial tubercle-trochlear groove distance was measured. Later it was examined whether there was correlation between these preoperative and postoperative tibial tubercle-trochlear groove measurements and the data recorded before operation. Results: Preoperative tibial tubercle-trochlear groove distance was found to be 8.83 ± 3.54, postoperative tibial tubercle-trochlear groovedistance was found to be 8.30 ± 3.89 and preoperative-postoperative tibial tubercle-trochlear groove variation was found to be 0,52 ± 3,64 (p = 0,337). In the patients whose alignment was 10 degrees or less, Pre-Op tibial tubercle-trochlear groove distance was measured as 8.74 ± 3.18 and in the patients whose alignment was more than 10 degrees, it was measured as 8.89 ± 3,83 (p = 0.888). In the patients whose alignment was 10 degrees or less, Post-Op tibial tubercle-trochlear groove distance was measured as 8.00 ± 2.85 and in the patients whose alignment was more than 10 degrees, it was measured as 8.52 ± 4.52 (p = 0.661). In the patients whose alignment was 10 degrees or less, tibial tubercle-trochlear groove distance variation was measured as 0.74 ± 3.25 and in the patients whose alignment was more than 10 degrees, it was measured as 0.37 ± 3.95 (p = 0.741). Coclusion: As a result, although tibial tubercle-trochlear groove distance was observed with a great variation in the osteoarthritic knees at stage 3-4, it was nonetheless measured within normal limits and Post-Op variation was not meaningful. Since this is the first study in the literature on the measurement of tibial tubercle-trochlear groove distance in the total knee prosthesis applications, we hope that it would shed some light on similar studies to be conducted in the future.

The effect of patellar thickness on gait biomechanics following total knee arthroplasty

BACKGROUND

Patella resurfacing is commonly performed during total knee arthroplasty; however, determining the appropriate patellar thickness remains a challenge. The purpose of this study was to evaluate the role of post-TKA patellar thickness on knee extensor strength and biomechanical joint loading forces during walking and stair negotiation.

METHODS

Fifteen patients (21 knees) underwent gait analysis prior to TKA and post-TKA at six weeks, three months, six months, and one year. Knee extensor strength and biomechanics were collected during level walking and stair negotiation and analyzed using Pearson correlation coefficients.

RESULTS

Knee extensor strength was positively correlated to patellar thickness at three months and one year post-TKA (p ≤ .05). During walking, no significant correlations were present. During stair ascent, there was a positive correlation between patellar thickness and peak knee flexion angle one year post-TKA (p ≤ .05). During stair descent, there was a positive correlation between patellar thickness and maximum vertical ground reaction forces at one year post-TKA (p ≤ .01).

CONCLUSIONS

The loss of patellar thickness when compared to measured pre-resurfacing thickness was correlated with a decrease in knee extensor strength; however, changes in patellar thickness were not significantly correlated to biomechanical loading forces during walking. Increases in demand of activity increase the torque to the knee joint, which elicit increases in compensatory motions, likely reducing the extent to which differences in joint loading during stair negotiation may be attributable to changes in patellar thickness. Therefore, the effect of post-patellar thickness on patient function in primary TKA is limited.

Association Between Femoral Component Sagittal Positioning and Anterior Knee Pain in Total Knee Arthroplasty: A 10-Year Case-Control Follow-up Study of a Cruciate-Retaining Single-Radius Design

BACKGROUND

Anterior knee pain is the most common complication of total knee arthroplasty (TKA). The purpose of this study was to assess whether sagittal femoral component position is an independent predictor of anterior knee pain after cruciate-retaining single-radius TKA without routine patellar resurfacing.

METHODS

A prospective cohort study of 297 cruciate-retaining single-radius TKAs performed in 2006 and 2007 without routine patellar resurfacing identified 73 patients (25%) with anterior knee pain and 89 (30%) with no pain (controls) at 10 years. Patients were assessed preoperatively and at 1, 5, and 10 years postoperatively using patient-reported outcome measures (PROMs), including the Short Form-12 (SF-12), Oxford Knee Score (OKS), and satisfaction and expectation questionnaires. Variables that were assessed as predictors of anterior knee pain included demographic data, the indication for the TKA, early complications, stiffness requiring manipulation under anesthesia, and radiographic criteria (implant alignment, Insall-Salvati ratio, posterior condylar offset ratio, and anterior femoral offset ratio).

RESULTS

The 73 patients with anterior knee pain (mean age, 67.0 years [range, 38 to 82 years]; 48 [66%] female) had a mean visual analog scale (VAS) score of 34.3 (range, 5 to 100) compared with 0 for the 89 patients with no pain (mean age, 66.5 years [range, 41 to 82 years]; 60 [67%] female). The patients with anterior knee pain had mean femoral component flexion of -0.6° (95% confidence interval [CI] = -1.5° to 0.3°), which differed significantly from the value for the patients with no pain (1.42° [95% CI = 0.9° to 2.0°]; p < 0.001). The patients with and those without anterior knee pain also differed significantly with regard to the mean anterior femoral offset ratio (17.2% [95% CI = 15.6% to 18.8%] compared with 13.3% [95% CI = 11.1% to 15.5%]; p = 0.005) and the mean medial proximal tibial angle (89.7° [95% CI = 89.2° to 90.1°] compared with 88.9° [95% CI = 88.4° to 89.3°]; p = 0.009). All PROMs were worse in the anterior knee pain group at 10 years (p < 0.05), and the OKSs were worse at 1, 5, and 10 years (p < 0.05). Multivariate analysis confirmed femoral component flexion, the medial proximal tibial angle, and an Insall-Salvati ratio of <0.8 (patella baja) as independent predictors of anterior knee pain (R = 0.263). Femoral component extension of ≥0.5° predicted anterior knee pain with 87% sensitivity.

CONCLUSIONS

In our study, 25% of patients had anterior knee pain at 10 years following a single-radius cruciate-retaining TKA without routine patellar resurfacing. Sagittal plane positioning and alignment of the femoral component were associated with long-term anterior knee pain, with femoral component extension being a major risk factor.

LEVEL OF EVIDENCE

Therapeutic Level IV. See Instructions for Authors for a complete description of levels of evidence.

Kinematically aligned total knee arthroplasty reproduces native patellofemoral biomechanics during deep knee flexion

PURPOSE

The implant positioning for kinematically aligned total knee arthroplasty (TKA) differs fundamentally from conventional mechanically aligned TKA. This difference may affect patellofemoral (PF) biomechanics after TKA. This cadaveric study tested the hypothesis that kinematically aligned TKA would restore PF biomechanics to the native condition better than mechanically aligned TKA.

METHODS

Seven pairs (14 knees) of fresh-frozen cadavers were tested. All specimens were mounted on a customized knee-testing system and digitized using a Microscribe 3DLX instrument (Revware Inc., Raleigh, NC, USA) to measure patellar kinematics in terms of patellar varus/valgus rotation, medial/lateral position, flexion/extension rotation and proximal/distal position at knee flexion angles of 0°, 30°, 60°, 90°, and 120°. The medial and lateral PF joint contact pressure distributions at 120° of knee flexion were measured using a K-scan system (Tekscan Inc., Boston, MA, USA). All patellae remained unresurfaced. For each pair, one knee was randomly assigned to kinematically aligned TKA and the other to mechanically aligned TKA performed using the conventional measured resection technique. During kinematically aligned TKA, the amount of femur and tibia resected was equivalent to implant thickness to maintain the patient-specific joint line. All patellar kinematics were measured and compared between the native condition and after surgery.

RESULTS

The patellae of mechanically aligned TKA rotated more valgus and was positioned more laterally compared with those of kinematically aligned TKA at knee flexion angles ≥ 90°. Neither the patellar flexion/extension rotation nor the proximal/distal position differed between either prosthetic knee design and the native knee at all flexion angles. The contact pressure distribution between the medial and lateral PF joint after kinematically aligned TKA were similar to those of the native knee, while the lateral PF joint contact pressure after mechanically aligned TKA was higher than that of the native knee (p = 0.038).

CONCLUSIONS

Kinematically aligned TKA better restores patellar kinematics and PF contact pressure distribution to the native condition than mechanically aligned TKA during deep knee flexion. These findings provide clues to understand why kinematically aligned TKA is associated with less anterior knee pain and better PF functional performance compared to mechanically aligned TKA. Patients undergoing kinematically aligned TKA may experience a more normal feeling during deep knee flexion activities.

Low-grade infections as a possible cause of arthrofibrosis after total knee arthroplasty

Purpose

Arthrofibrosis after total knee arthroplasty represents a considerable burden for the patient and a therapeutic challenge for the practitioner. One possible cause discussed in the literature is a low-grade infection. This hypothesis should be examined within the scope of this retrospective study.

Patients and methods

Nineteen patients with clinical symptoms of arthrofibrosis after primary total knee arthroplasty were examined between January, 1999 and January, 2012. Incorrect positioning was radiologically ruled out. All patients were examined clinically (score of Freeman as well as Blauth and Jäger), radiologically (component and leg alignment, patella height according to Insall and Salvati), microbiologically (culture-based procedures), molecular biologically (PCR) and histologically in the course of an open revision of the prosthesis.

Results

According to the score of Freeman et al. (1977), a highly significant improvement in pain (p = 0.007) and in the overall score (p = 0.003) was shown. The knee joint mobility did not change significantly (p = 0.795). PCR was negative in 17 patients. One patient showed a PCR-positive result of the synovial membrane for Corynebacterium spp., while Staphylococcus warneri was detected in the culture. Another patient had a positive result of synovia PCR for Enterococcus cecorum as well as Corynebacterium spp. However, this culture was sterile. In 16 patient samples, no bacterial growth was detectable. Two samples were not evaluable. The main histopathological findings were synovialitis and fibrosis.

Conclusion

The hypothesis of low-grade-infection-induced arthrofibrosis after total knee arthroplasty could not be confirmed in this study. However, based on this small study population the conclusion needs to be confirmed by new and larger studies, ideally prospectively designed including a control group.

The influence of compressive forces across the patellofemoral joint on patient-reported outcome after bi-cruciate stabilized total knee arthroplasty

AIMS

Patellofemoral problems are a common complication of total knee arthroplasty. A high compressive force across the patellofemoral joint may affect patient-reported outcome. However, the relationship between patient-reported outcome and the intraoperative patellofemoral contact force has not been investigated. The purpose of this study was to determine whether or not a high intraoperative patellofemoral compressive force affects patient-reported outcome.

PATIENTS AND METHODS

This prospective study included 42 patients (42 knees) with varus-type osteoarthritis who underwent a bi-cruciate stabilized total knee arthroplasty and in whom the planned alignment was confirmed on 3D CT. Of the 42 patients, 36 were women and six were men. Their mean age was 72.3 years (61 to 87) and their mean body mass index (BMI) was 24.4 kg/m ² (18.2 to 34.3). After implantation of the femoral and tibial components, the compressive force across the patellofemoral joint was measured at 10°, 30°, 60°, 90°, 120°, and 140° of flexion using a load cell (Kyowa Electronic Instruments Co., Ltd., Tokyo, Japan) manufactured in the same shape as the patellar implant. Multiple regression analyses were conducted to investigate the relationship between intraoperative patellofemoral compressive force and patient-reported outcome two years after implantation.

RESULTS

No patient had anterior knee pain after total knee arthroplasty. The compressive force across the patellofemoral joint at 140°of flexion was negatively correlated with patient satisfaction (R ² = 0.458; β = -0.706; p = 0. 041) and Forgotten Joint Score-12 (FJS-12; R ² = .378; β = -0.636; p = 0. 036). The compressive force across the patellofemoral joint at 60° of flexion was negatively correlated with the patella score (R ² = 0.417; β = -0.688; p = 0. 046).

CONCLUSION

Patient satisfaction, FJS-12, and patella score were affected by the patellofemoral compressive force at 60° and 140° of flexion. Reduction of the patellofemoral compressive forces at 60° and 140° of flexion angle during total knee arthroplasty may improve patient-reported outcome, but has no effect on anterior knee pain.

Patella tracking calculation from patellofemoral positions at finite angles of knee flexion

Patellofemoral (PF) pain is a common knee disease. Patella tracking has a significant correlation with PF pain, therefore it could be used as an index for diagnosis and treatment evaluation. Previous research has proposed a method for measuring in vivo patella tracking by means of an interpolation algorithm. The present study aimed to quantify the effect of the interpolation parameters on the accuracy of the patella tracking with a motion capture experiment. The precise patella tracking of 5 knee specimens was collected and compared with the interpolated tracking. The results showed that the total interpolation error decreased to 2 mm with the number of interpolation angles increasing to 6. The number of interpolation reference points had a slight influence on the accuracy. The findings consolidated the feasibility of using interpolation to measure the in vivo patella tracking, and can help to optimize the accuracy and efficiency of the methodology.

Patient-Specific Simulated Dynamics After Total Knee Arthroplasty Correlate With Patient-Reported Outcomes

BACKGROUND

Component alignment variation following total knee arthroplasty (TKA) does not fully explain the instance of long-term postoperative pain. Joint dynamics following TKA vary with component alignment and patient-specific musculoskeletal anatomy. Computational simulations allow joint dynamics outcomes to be studied across populations. This study aims to determine if simulated postoperative TKA joint dynamics correlate with patient-reported outcomes.

METHODS

Landmarking and 3D registration of implants was performed on 96 segmented postoperative computed tomography scans of TKAs. A cadaver rig-validated platform for generating patient-specific simulation of deep knee bend kinematics was run for each patient. Resultant dynamic outcomes were correlated with a 12-month postoperative Knee Injury and Osteoarthritis Outcome Score (KOOS). A Classification and Regression Tree (CART) was used for determining nonlinear relationships.

RESULTS

Nonlinear relationships between the KOOS pain score and rollback and dynamic coronal alignment were found to be significant. Combining a dynamic coronal angular change from extension to full flexion between 0° and 4° varus (long leg axis) and measured rollback of no more than 6 mm without rollforward formed a "kinematic safe zone" of outcomes in which the postoperative KOOS score is 10.5 points higher (P = .013).

CONCLUSION

The study showed statistically significant correlations between kinematic factors in a simulation of postoperative TKA and postoperative KOOS scores. The presence of a dynamic safe zone in the data suggests a potential optimal target for any given individual patient's joint dynamics and the opportunity to preoperatively determine a patient-specific alignment target to achieve those joint dynamics.

Medial stabilized and posterior stabilized TKA affect patellofemoral kinematics and retropatellar pressure distribution differently

PURPOSE

Patellofemoral kinematics and retropatellar pressure distribution change after total knee arthroplasty (TKA). It was hypothesized that different TKA designs will show altered retropatellar pressure distribution patterns and different patellofemoral kinematics according to their design characteristics.

METHODS

Twelve fresh-frozen knee specimens were tested dynamically in a knee rig. Each specimen was measured native, after TKA with a posterior stabilized design (PS) and after TKA with a medial stabilized design (MS). Retropatellar pressure distribution was measured using a pressure sensitive foil which was subdivided into three areas (lateral and medial facet and patellar ridge). Patellofemoral kinematics were measured by an ultrasonic-based three-dimensional motion system (Zebris CMS20, Isny Germany).

RESULTS

Significant changes in patellofemoral kinematics and retropatellar pressure distribution were found in both TKA types when compared to the native situation. Mean retropatellar contact areas were significantly smaller after TKA (native: 241.1 ± 75.6 mm², MS: 197.7 ± 74.5 mm², PS: 181.2 ± 56.7 mm², native vs. MS p < 0.001; native vs. PS p < 0.001). The mean peak pressures were significantly higher after TKA. The increased peak pressures were however seen in different areas: medial and lateral facet in the PS-design (p < 0.001), ridge in the MS design (p < 0.001). Different patellofemoral kinematics were found in both TKA designs when compared to the native knee during flexion and extension with a more medial patella tracking.

CONCLUSION

Patellofemoral kinematics and retropatellar pressure change after TKA in different manner depending on the type of TKA used. Surgeons should be aware of influencing the risks of patellofermoral complications by the choice of the prosthesis design.

Safety and Efficacy of 6.2 mm Patellar Button in Resurfacing Less than 20 mm Thin Patella: A Matched Pair Analysis

Purpose

Restoring the native patellar thickness after patellar resurfacing provides optimal function of the knee after arthroplasty and minimises complications related to the patellofemoral articulation. The aim of this study was to assess the usefulness of a thin patellar button (6.2 mm) in patients with a patella thickness of less than 20 mm during total knee arthroplasty.

Materials and Methods

This is a retrospective case control study. A total of 54 female patients with an intraoperative patellar thickness of <20 mm, resurfaced with a patellar button of 6.2 mm in thickness were identified (group 1). They were matched with 54 patients with a patellar thickness of 20–23 mm, resurfaced with a patellar button of 8 mm (group 2), based on age, sex, body mass index, and deformity. A clinical and radiological evaluation was done at a minimum 2-year follow-up.

Results

The preoperative mean patellar thickness was 18.94±1.07 mm and was restored to 19.06±0.79 mm in group 1, as compared to 21.63±0.99 mm and 21.72±0.99 mm in group 2. The mean postoperative range of motion was 122.22°±9.25° in group 1 and 123.52°±8.72° in group 2 (p=0.13). No patellar bone or button related complications were observed in any patient in either group.

Conclusions

The 6.2 mm thin patella is useful to restore the native thickness in patients with a patellar thickness of less than 20 mm without risk of button fracture, loosening or overstuffing.

Patellar tracking in primary total knee arthroplasty

This is a review of the recent literature of the various factors that affect patellar tracking following total knee arthroplasty (TKA).

Patellar tracking principally depends on the pre-existing patellar tracking and the rotational alignment of the femoral and tibial implants, but the detailed movements depend on the patellar shape. The latter means that the patellar kinematics of any implanted TKA does not return to normal.

Laboratory cadaveric studies use normal knees and non-activity-based testing conditions and so may not translate into clinical findings.

The recent literature has not added anything significant to change established clinical practice in achieving satisfactory patellar tracking following TKA.

Cite this article: EFORT Open Rev 2018;3:106-113. DOI: 10.1302/2058-5241.3.170036.