Sorption of phosphate onto giant reed based adsorbent: FTIR, Raman spectrum analysis and dynamic sorption/desorption properties in filter bed

Adsorption of Cr(VI) and phosphate anions by amino-functionalized palm oil fibers

This work developed a novel sustainable adsorbent (PF-Aq) prepared by the amino-functionalization of palm oil fibers (PF). XPS, SEM/EDS, TGA/DSC, and FT-IR techniques proved the successful functionalization of the PF with the amino group. The PF-Aq adsorbent presents a high adsorption capacity for phosphate and Cr(VI) ions. Adsorption kinetics of the ions onto the PF-Aq followed the general-order models, with 240- and 300-min equilibrium times for phosphate and Cr(VI), respectively. The Freundlich equilibrium model can explain the adsorption of phosphate and Cr(VI) on the PF-Aq. Besides, the maximum adsorption capacities were 151.07 mg g-1 for phosphate and 206.08 mg g-1 for Cr(VI). The best pH for the adsorption of both ions on PF-Aq was 4.0. Interestingly, adsorption was exothermic for phosphate and endothermic for Cr(VI). The adsorption capacities were reduced by 16% for phosphate and 10% for Cr(VI) after 5 adsorption-desorption cycles, demonstrating the good recyclability of the PF-Aq. It can be concluded that PF-Aq is a relevant adsorbent to uptake phosphate and Cr(VI) from water due to its high adsorption capacity, low cost, recyclability, availability, and fast kinetics. Finally, the excellent adsorption potential results from inserting amino groups in the PF, allowing electrostatic interactions between adsorbent and adsorbate.

Remarkably Enhanced Phosphate Sequestration from Waters by Biochar with High-Density Quaternary Ammonium Groups

A new biochar (N-BC) was fabricated by incorporating high-density positively charged quaternary ammonium groups into the pristine biochar without any adsorption for phosphate. N-BC can highly efficiently remove phosphate with an optimal pH of 5.0, a maximum experimental adsorption capacity of 30 mg of P/g, and an adsorption equilibrium time of 180 min. The predicted pore diffusion coefficient D (the diffused surface area of the adsorbate for unit time) for phosphate adsorption by N-BC was 5.3 × 10-9 cm2/s. N-BC can still capture phosphate in the copresence of anion Cl- with a molar concentration 50 times that of phosphate. The exhausted N-BC was completely regenerated using a 10 wt % NaOH solution and further reused without any observable loss in adsorption capacity. Moreover, N-BC yielded ∼324 bed volumes (BV) of wastewater containing 1 mg P/L phosphate and 50 mg/L Cl- before breakthrough occurring (<0.1 mg P/L in effluent) in a fixed-bed column operation system. The introduced quaternary ammonium groups covalently bound to biochar played a dominant role in phosphate sequestration by N-BC through forming the out-sphere complexation with phosphate. All results imply that it is of promising prospect for N-BC practical application for phosphate purification from waters. The present study provided a new strategy to expand the application of biochar, usually serving as an adsorbent for cationic pollutants, to the purification of anionic pollutants such as phosphate from waters.

Mechanism of Phosphate Desorption from Activated Red Mud Particle Adsorbents

Herein, activated red mud particles are used as adsorbents for phosphorus adsorption. HCl solutions with different concentrations and deionized water are employed for desorption tests, and the desorption mechanism under the following optimal conditions is investigated: HCl concentration = 0.2 mol/L, desorbent dosage = 0.15 L/g, desorption temperature = 35 °C, and desorption time = 12 h. Under these conditions, the phosphate desorption rate and amount reach 99.11% and 11.29 mg/g, respectively. Notably, the Langmuir isothermal and pseudo-second-order kinetic linear models exhibit consistent results: monomolecular-layer surface desorption is dominant, and chemical desorption limits the rate of surface desorption. Thermodynamic analysis indicates that phosphorus desorption by the desorbents is spontaneous and that high temperatures promote such desorption. Moreover, an intraparticle diffusion model demonstrates that the removal of phosphorus in the form of precipitation from the surface of an activated hematite particle adsorbent primarily occurs via a chemical reaction, and surface micromorphological analysis indicates that desorption is primarily accompanied by Ca dissolution, followed by Al and Fe dissolutions. The desorbents react with the active elements in red mud, and the vibrations of the [SiO4]4- functional groups of calcium-iron garnet and calcite or aragonite disappear. Further, in Fourier-transform infrared spectra, the intensities of the peaks corresponding to the PO43- group considerably decrease. Thus, desorption primarily involves monomolecular-layer chemical desorption.

Protection of Mono and Polyunsaturated Fatty Acids from Grapeseed Oil by Spray Drying Using Green Biopolymers as Wall Material

One of the most common ways to protect oils is microencapsulation, which includes the use of encapsulating agents. Due to the environmental problems facing humanity, this study seeks to combine green biopolymers (microcrystalline cellulose and whey protein isolate) that function as encapsulating agents for grapeseed oil. Grapeseed oil that is obtained from agro-industrial waste has shown health benefits, including cardioprotective, anticancer, antimicrobial, and anti-inflammatory properties. These health benefits have been mainly associated with monounsaturated (MUFA) and polyunsaturated (PUFA) fatty acids. In this sense, it has been observed that grapeseed oil can be easily modified by environmental factors such as oxygen, high temperatures, and light, showing the instability and easy degradation of grapeseed oil. In this study, grapeseed oil was encapsulated using the spray-drying technique to conserve its lipidic profile. Powder recovery of the grapeseed oil microcapsules ranged from 65% to 70%. The encapsulation efficiency of the microcapsules varied between 80% and 85%. The FTIR analysis showed chemical interactions that demonstrate chemisorption between the grapeseed oil and the encapsulating material, while the SEM micrographs showed a correct encapsulation in a spherical shape. Gas chromatography showed that the lipid profile of grapeseed oil is preserved thanks to microencapsulation. Release tests showed 80% desorption within the first three hours at pH 5.8. Overall, whey protein and microcrystalline cellulose could be used as a wall material to protect grapeseed oil with the potential application of controlled delivery of fatty acids microcapsules.

Removal of Phosphate from Wastewater with a Recyclable La-Based Particulate Adsorbent in a Small-Scale Reactor

It is crucial to develop an effective and easily recoverable phosphate absorbent for the control of eutrophication problems in polluted rivers. In this study, a stable particulate adsorbent with a diameter of 5 mm synthesized from lanthanum, activated carbon, and zeolite (La-CZ) was developed, characterized, and tested for the removal of phosphate from wastewater in a small-scale reactor, which was designed to easily recycle La-CZ with a basket. Batch studies showed that La-CZ could reach adsorption equilibrium within 2 h and the maximum phosphate sorption capacity was 18.2 mg g−1. The experimental data showed good compliance with the Langmuir isotherm model and pseudo-second-order kinetic model, implying that chemisorption dominates the phosphate uptake process. La-CZ exhibited a stable adsorption capacity over a wide pH range (3–7), while the adsorption capacity decreased slightly under alkaline conditions. Although Nitrates (NO3−) and Carbonate (CO32−) had some effects, normal coexisting ions such as Chloride (Cl−), Sulfate (SO42−), and Fluorine (F−) had no significant effects on the phosphate adsorption capacity of La-CZ. The main form of phosphate removed from the reaction system was HCl-P (77.68%), as determined through phosphorus fractionation. In particular, this study designed a replaceable filler-type reactor integrating a reflux and aeration system, 98.8% of phosphorus could be removed from actual wastewater, and La-CZ could be reclaimed easily. This work provides an excellent reference for particulate adsorbents that can efficiently remove phosphate in practical applications in the future.

Removal of inorganic toxic contaminants from wastewater using sustainable biomass: A review

Lignocellulosic biomass is most abundant, ecofriendly and sustainable material on this green planet which has received great attention due to exhaustion of petroleum reserves and various environmental complications. Due to its abundance and sustainability, it has been opted in number of advanced applications i.e. synthesis of green chemicals, biofuels, paper, packaging, biocomposite and for discharge of toxic contaminants from wastewaters. Utilization of sustainable biomass for removal of toxic pollutants from wastewater is robust technique due to its low-cost and easy availability. In this review, we have summarized removal of inorganic pollutants by sustainable lignocellulosic biomass in their natural as well as in chemically functionalized form. Various techniques for modification of sustainable biomass have been discussed and it was found that modified biomass showed better biosorption ability as compared to natural biomass. We conclude that modified biomass biosorbents are useful for removal of toxic inorganic pollutants to deficient levels. Several modification strategies can improve the qualities of biosorbent, however grafting is the most successful among them, as demonstrated in this work. The numerous grafting methods using a free radical grafting process are also summarized in this review article. This review also gathers studies comparing sorption capabilities with and without modification using modified and unmodified biosorbents. Chemically modified cellulosic biomass is favoured over untreated biomass because it has a higher adsorption efficiency, which is favoured by a large number of reactive binding sites, improved ion-exchange characteristics, and more functional groups available after modification.

Rare earth elements (REE) for the removal and recovery of phosphorus: A review

There is little doubt that 'rock phosphate' reserves are decreasing, with phosphorus (P) peak to be reached in the coming decades. Hence, removal and recovery of phosphorus (P) from alternative nutrient-rich waste streams is critical and of great importance owing to its essential role in agricultural productivity. Adsorption technique is efficient, cost-effective, and sustainable for P recovery from waste streams which otherwise can cause eutrophication in receiving waters. As selective P sorption using rare earth elements (REE) are gaining considerable attention, this review extensively focuses on P recovery by utilising a range of REE-incorporated adsorbents. The review briefly provides existing knowledge of P in various waste streams, and examines the chemistry and behaviour of REE in soil and water in detail. The impact of interfering ions on P removal using REE, adsorbent regeneration for reuse, and life cycle assessment of REE are further explored. While it is clear that REE-sorbents have excellent potential to recover P from wastewaters and to be used as fertilisers, there are gaps to be addressed. Future studies should target recovery and reuse of REE as P fertilisers using real wastewaters. More field trials of synthesized REE-sorbents are highly recommended before practical application.

Blind source separation of coexisting background in Raman spectra

Due to the Raman signal coexists with other scatter spectra which leads to the low ratio of the wanted signal and high background, the appropriate method should be applied to enhance this ratio. The nature of raw spectra is a multi-source system, so its determinacy must be ensured by multi-input. Besides, the faithfulness of output should be provided. Then, the huge fall within the frequencies of Raman and background almost satisfies separating demand for independent component analysis (ICA), and this analysis can give help to the achievement of the two type signals classing and estimate the optimal number of source and match ICA output signals to Raman or background. Thus, based on ICA and the mixing-entropy criteria, the background and Raman adapting calibration kit (BRACK) method is proposed, which is a kind of multiple raw spectral inputs and multiple output (MIMO) method. This method firstly divides the raw data into two parts of Raman and background by ICA, identifies Raman signal by entropy criterion, then restores the part of Raman signal. BRACK method obtains several advantages, for instance, well-adapted, no need for any additional option or extra-intervention, high fidelity, and no unwanted external information. In principle, the correction of background and Raman signals can be expected to be completed by BRACK method.

Phosphate recovery with granular acid-activated neutralized red mud: Fixed-bed column performance and breakthrough curve modelling

Granular acid-activated neutralized red mud (AaN-RM) has been successfully prepared with good chemical stability and physical strength. However, its potential for industrial application remains unknown. Therefore, the performance of granular AaN-RM for phosphate recovery in a fixed-bed column was investigated. The results demonstrated that the phosphate adsorption performance of granular AaN-RM in a fixed-bed column was affected by various operational parameters, such as the bed depth, flow rate, initial solution pH and initial phosphate concentration. With the optimal empty-bed contact time (EBCT) of 24.27 min, the number of processed bed volumes and the phosphate adsorption capacity reached 496.95 and 84.80 mg/g, respectively. Then, the saturated fixed-bed column could be effectively regenerated with a 0.5 mol/L HCl solution. The desorption efficiency remained as high as 83.45% with a low weight loss of 3.57% in the fifth regeneration cycle. In addition, breakthrough curve modelling showed that a 5-9-1 feed-forward artificial neural network (ANN) could be effectively applied for the optimization of the fixed-bed adsorption system; the coefficient of determination (R²) and the root mean square error (RMSE) evaluated on the validation-testing data were 0.9987 and 0.0183, respectively. Therefore, granular AaN-RM fixed-bed adsorption exhibits promising potential for phosphate removal and recovery from polluted water.

Greenhouse tomato plant roots/carboxymethyl cellulose method for the efficient removal and recovery of inorganic phosphate from agricultural wastewater

Phosphate (P) is a biologically important compound that is commonly incorporated into fertilizers. Wastewater from agricultural processes results in excessive accumulation of P and eutrophication of lakes. We have developed a system for the remediation, recovery, and potential reuse of P from agricultural wastewater using tomato plant roots (roots) as a capture matrix and carboxymethyl cellulose (CMC) as an eluent and enhancer of P precipitation. Untreated roots can bind up to 55.2 ± 15.2 grams of P per kilogram (g/kg) of roots in comparison to the maximum 8.2 ± 1.5 g/kg bound by the previously used iron-chitosan (Fe-chito). The addition of CMC enhances the precipitation of P with a clearance of 97.2% as opposed to 33.3% without CMC. On site tests show an average removal of 226.5 μg/L per day or a total of ∼28 g of P removed after 23 days. This corresponds to a 71% P removal rate.

Hydrated lanthanum oxide-modified diatomite as highly efficient adsorbent for low-concentration phosphate removal from secondary effluents

The requirement to the phosphorus (P) emission from wastewater treatment plants (WWTPs) is becoming increasingly strict, which makes an advanced treatment for the low-concentration phosphate removal from secondary effluents indispensable. In present work, hydrated lanthanum (La) oxide-modified diatomite composites (La-diatomite) were fabricated by a facile method and employed as the highly efficient adsorbent for the low-concentration phosphate removal from simulating secondary effluents. Comparative experiments indicated that the La-diatomite treated by 0.1 mol/L LaCl₃ exhibited the highest La availability (P/La molar ratio of 2.30) and performed good selectivity to phosphate adsorption even with the coexistence of competing anions and humic acid. The maximum P adsorption capacity reached to 58.7 mg P/g and the 96% P was removed quickly within 30 min at initial phosphate concentration 2 mg P/L. Insignificant La leaching was observed during the process due to the La stabilization by macroporous diatomite. Eight cycles of adsorption-desorption experiments revealed that the excellent repeated use property of La-diatomite. At the column test, La-diatomite showed superior treatment capacities of 3455 kg water/kg La-diatomite for simulated secondary effluents. The La-diatomite maintained high and stable adsorption effectiveness in wide pH range, which should be attributed to the synergistic effect of electrostatic interactions, ligand exchange and Lewis acid-based interaction. This work might provide a candidate for low-concentration phosphate removal from secondary effluent to alleviate the eutrophication.

Applications of magnetic hybrid adsorbent derived from waste biomass for the removal of metal ions and reduction of 4-nitrophenol

The use of industrial waste to synthesize materials of technological interest is a rational way to minimize or solve environmental pollution problems. This work investigates the adsorption of cadmium and lead ions by magnetic hybrid adsorbents synthesized using the in natura biomasses coconut mesocarp (CCFe), sawdust (SAFe), and termite nest (TEFe) for the organic phases and magnetic cobalt ferrite as the inorganic phase. The formation of a cobalt ferrite phase was confirmed by XRD. The use of XRD and FTIR analyses revealed the presence of organic matter in the structure of the material. Removal assays performed at different pH values (2.0-8.0) showed the effectiveness of the adsorbent for the removal of Pb²⁺ at pH 3.0 and Cd²⁺ at pH 4.0. The adsorption processes showed fast kinetics, with removal of 79-86% of Pb²⁺ and 49% of Cd²⁺ within only 5 min, and removal of 92-96% of the metal species at equilibrium. In the case of cadmium, the hybrid sorbents (CCFe, SAFe, and TEFe) showed high removal capacity after three reuse cycles, while the removal of lead decreased from 99% to 40%. The adsorbent matrices saturated with the recovered cadmium and lead ions showed excellent catalytic performance in the reduction of 4-nitrophenol, with 99.9% conversion within 43-56 s. The materials showed high capacities for reuse in three successive reduction cycles. The findings highlight the effectiveness of an industrial symbiosis approach to the development of new technologically important materials.

Effectiveness and mechanisms of phosphate adsorption on iron-modified biochars derived from waste activated sludge

Excessive discharge of phosphate (P) into the surface water is the key factor to cause the eutrophication, so its removal has aroused much attention in recent years. In this study, different iron modification (chemical co-precipitation of Fe³⁺/Fe²⁺ or FeCl₃ impregnation) was used to improve the phosphate adsorption capacity of waste activated sludge (WAS)-based biochar. Comparative tests demonstrated that the FeCl₃-impregnated WAS-based biochar exhibited much superior phosphate adsorption capacity (111.0mg/g) in all as-prepared samples and performed well even under the interferences with pH and coexisting ions. X-ray diffraction (XRD) analyzes indicated that the iron in FeCl₃-impregnated WAS-based biochar existed mainly in amorphous phase, as hematite and amorphous hydroxides forms, which was of great benefit to the phosphate adsorption. Besides, ligand exchange plays important role in the adsorption of phosphate. The WAS-based biochar kept over 60% phosphate removal efficiency after five recycles.

Biosorption and retention of orthophosphate onto Ca(OH)2-pretreated biomass of Phragmites sp

The biosorption of phosphorus in the form of orthophosphate (Po) from wastewater using biomass as the sorbent is of potential importance because the Po-loaded biomass could be applied in the agricultural sector as fertilizer and soil conditioner. However, biomass generally displays a very low affinity for Po sorption and therefore biomass surface modification is required. In the present study, the biomass (as model grinded leaves of Phragmites sp. were used) was pretreated with Ca(OH)2 to enhance Po biosorption capacity (qe). The results indicate that the alkaline pretreatment resulted in a modification of surface functional groups. It was concluded that the main sorption mechanisms were ligand exchange and electrostatic attraction. A series of experiments were conducted to investigate the performance of the pretreated biomass for Po uptake under various conditions. Isotherm and thermodynamic studies were also applied and analyzed. The biosorption process was best described by the pseudo-second order kinetic model and Langmuir isotherm, which gave a qmax of 12.27mgP/g at 25°C and pH7. The Ca(OH)2 treated Phragmites biomass applied in this study for Po recovery may present some potential advantages in terms of costs and environmental impact.

Adsorption of phosphate on surface of magnetic reed: characteristics, kinetic, isotherm, desorption, competitive and mechanistic studies

A magnetic biocomposite was prepared by Fe₃O₄in situ co-precipitation and amine functionalization processes by using virgin reed as starting material.

Adsorption of phosphate from aqueous solutions and sewage using zirconium loaded okara (ZLO): Fixed-bed column study

This study explores the potential of removing phosphorus from aqueous solutions and sewage by Zr(IV)-loaded okara (ZLO) in the fixed-bed column. Soybean residue (okara) was impregnated with 0.25M Zr(IV) solution to prepare active binding sites for phosphate. The effect of several factors, including flow rate, bed height, initial phosphorus concentration, pH and adsorbent particle size on the performance of ZLO was examined. The maximum dynamic adsorption capacity of ZLO for phosphorus was estimated to be 16.43mg/g. Breakthrough curve modeling indicated that Adams-Bohart model and Thomas model fitted the experimental data better than Yoon-Nelson model. After treatment with ZLO packed bed column, the effluent could meet the discharge standard for phosphorus in Australia. Successful desorption and regeneration were achieved with 0.2 NaOH and 0.1 HCl, respectively. The results prove that ZLO can be used as a promising phosphorus adsorbent in the dynamic adsorption system.

Perchlorate adsorption onto orange peel modified by cross-linking amine groups from aqueous solutions

Orange peel was made into a highly efficient bio-sorbent by modification with cross-linking amine groups for perchlorate removal. Bench-scale experiments were performed to explore the factors affecting the perchlorate adsorption onto the modified orange peel (MOP). Perchlorate could be removed effectively at a wide range of pH (from 1.5 to 11). The maximum adsorption capacity of MOP for perchlorate was calculated as 154.1 mg/g within 15 min. The Redlich-Peterson model was fitted to the adsorption isotherm very well (R2>0.99). The adsorption process was spontaneous and exothermic, which was proved by thermodynamic parameters (Gibbs energy and enthalpy). The pseudo-second-order kinetic model could provide satisfactory fitting of the experimental data (R2>0.99). The scanning electron microscopy and energy-dispersive X-ray analysis indicated that the surface of MOP became smooth and the contents of N and Cl in MOP were increased during the modification process. Elemental analysis results showed that the nitrogen content in MOP was increased to 5.5%, while it was 1.06% in orange peel. The adsorption mechanism was also explored using zeta potential and Fourier transform infrared spectroscopy analysis. Ion exchange was the primary mechanism responsible for uptake of perchlorate onto MOP.

Modification of agricultural waste/by-products for enhanced phosphate removal and recovery: potential and obstacles

There is a growing trend to employ agricultural waste/by-products (AWBs) as the substrates for the development of phosphate biosorbents. Nevertheless, due to the lack of anion binding sites, natural AWBs are usually inefficient in phosphate decontamination. Consequently, modification plays a vital role in improving phosphate sorption's property of raw AWBs. This review paper evaluates all existing methods of modification. The literatures indicate that modification can significantly improve phosphate removal ability of AWBs by retaining phosphate ion onto modified AWBs principally via ion exchange (electrostatic interaction) and ligand exchange mechanisms. So far, little work has been done on the beneficial use of modified AWBs for the phosphorus recovery from aqueous solutions. The poor recyclability of modified AWBs could be responsible for their limited application. Hence, further study is essential to search for novel, cost-effective, and green methods of modification.

Phosphorus elimination from aqueous solution using 'zirconium loaded okara' as a biosorbent

This work deals with the capture of phosphorus from aqueous solutions by biosorption onto zirconium loaded okara (ZLO). The batch-mode experiments were conducted to examine the effect of pH, biosorbent dose, initial phosphorus concentration, contact time, and temperature on the process. It was found that, the adsorption was most favored in the pH range of 2-6. The optimal doses for the adsorption, at initial phosphorus concentrations of 5, 10, 25, 50mg/L were 2, 3, 7, 10g/L, respectively. The maximum adsorption capacity of ZLO was approximately 44.13mg PO4/g at 298K. The phosphate removal was rapid, reaching 95% in 30min. Freundlich model best fitted the equilibrium data, while Pseudo-second order model satisfactorily described the kinetic results. Thermodynamic analysis revealed feasible, spontaneous, and endothermic nature of the process. The research would be beneficial for developing a promising, eco-friendly phosphorus biosorbent from a plentiful AWB - okara.

A green strategy for desorption of trihalomethanes adsorbed by humin and reuse of the fixed bed column

The objective of the present work was to develop a thermal desorption method for the removal of trihalomethanes (THM) adsorbed by humin, followed by multiple recycling of the fixed bed column in order to avoid excessive consumption of materials and reduce operating costs. The results obtained for adsorption on a fixed bed column confirmed the effectiveness of humin as an adsorbent, extracting between 45.9% and 90.1% of the total THM (TTHM). In none of the tests was the column fully saturated after 10h. Experiments involving thermal desorption were used to evaluate the potential of the technique for column regeneration. The adsorptive capacity of the humin bed increased significantly (p<0.05) between the first and fifth desorption cycle, by 18.9%, 18.1%, 24.2%, 20.2% and 24.2% for CHBr(3), CHBr(2)Cl, CHBrCl(2), CHCl(3) and TTHM, respectively.

Formaldehyde removal by potted plant-soil systems

Formaldehyde is a major indoor air pollutant. Formaldehyde removal from indoor air conduces to decrease the health risk for urban inhabitants. In this study, a dynamic chamber technique was employed to investigate formaldehyde removal by potted spider plant (Chlorphytum comosum), aloe (Aloe vera) and golden pothos (Epipremnum aureum) with potted soils. The results showed that the potted plant-soil systems could remove formaldehyde from air in a long time. The spider plant-soil system had the highest formaldehyde removal capacity compared with others. Higher metabolisms in plants and microorganisms in daytime may give a reasonable explanation for higher formaldehyde removal capacities for plant-soil systems in daytime. The order of formaldehyde removal capacity for the three plant species agreed well with the sequence of formaldehyde dehydrogenase activities from plant leaves. Formaldehyde removal by plant may be diffusion-limited rather than reaction-limited since the detached formaldehyde dehydrogenase activities from the leaves of the three plant species were higher than in vivo metabolic capacities. Formaldehyde in air can be largely absorbed and metabolized by the microorganisms in the potted soils indicating that further elevating formaldehyde removal capacity for plant-soil system will be realized by increasing exposed surface of potted soil.