Harvesting of microalgae by flocculation with poly (γ-glutamic acid)

Nano magnetite assisted flocculation for efficient harvesting of lutein and lipid producing microalgae biomass

For commercial scale algal biorefining, harvesting cost is a major bottleneck. Thus, a cost-effective, less-energy intensive, and efficient harvesting method is being investigated. Among several harvesting methods, magnetic flocculation offers the benefits of modest operation, energy savings and quick separation. This study aims to develop novel magnetite-(Fe₃O₄) nanoparticles (MNPs) of 20 nm average size and their high reusability potential to reduce the harvesting cost of microalgae biomass. The MNPs were synthesized and characterized using FTIR, Zeta analyzer, and SEM before performing on Chlorella sorokiniana Kh12 and Tu5. For maximum harvesting efficiency >99%, the optimal culture pH, MNPs concentration, and agitation speed were 3, 200 mg/L, and 450 rpm, respectively. Subsequently, MNPs were recovered via alkaline treatment and reused up to 5 cycles as they retained their reactivity and harvesting efficiency. The studied MNPs-based harvesting method could be adopted at a commercial scale for cost-effective algae biorefinery in the future.

A innovative stepwise strategy using magnetic Fe3O4-co-graft tannin/polyethyleneimine composites in a coupled process of sulfate radical-advanced oxidation processes to control harmful algal blooms

A novel co-graft tannin and polyethyleneimine co-coating magnetic composite (TP@Fe₃O₄) was prepared in the study. On this premise, an unique stepwise efficient strategy based on magnetic flocculation and Sulfate radical (SO₄^•-)-advanced oxidation processes (S-AOPs) for eliminating Microcystis aeruginosa (M. aeruginosa) and algal organic matters (AOMs) was presented. Due to the high positive charge of TP@Fe₃O₄, a > 99 % high algae removal rate was obtained at a modest TP@Fe₃O₄ dosage of 100 mg/L at pH = 8.0 with a short separation time of 5 min. Further, peroxymonosulfate (PMS) treatment was employed as a pre-oxidation method to lower cell stability and promote M. aeruginosa removal by subsequent TP@Fe₃O₄ flocculation. The PMS/TP@Fe₃O₄ system successfully cuts the optimum dose of TP@Fe₃O₄ in half (50 mg/L) without causing obvious cell damage. Following algal fast magnetic separation, ultraviolet (UV) was introduced to activate PMS to totally degrade AOM and microcystin. Response surface methodology (RSM) demonstrated that UV/PMS oxidation removed > 80 % of DOC and > 94 % of microcystin under optimal conditions. SO₄^•- was the main radical species that aided in the elimination of AOM. This is the first study to use magnetic flocculation in conjunction with AOPs to mitigate harmful algal blooms, which can enable the non-destructive eradication of M. aeruginosa while also efficiently degrading AOMs.

N-Acyl-Homoserine Lactone (AHL)-Mediated Microalgal-Bacterial Communication Driving Chlorella-Activated Sludge Bacterial Biofloc Formation

N-acyl-homoserine lactones (AHLs) as autoinducers of Gram-negative bacteria for quorum sensing regulation have shown positive effects on the production of aromatic proteins in extracellular polymeric substances (EPSs) during bioflocculation. To investigate the role of AHLs in aromatic protein production, a Chlorella-bacteria system with great bioflocculation was established via fed-batch cultivation. Tryptophan and aromatic proteins as the main compounds in the EPS of bioflocs showed an increasing trend during fed-batch cultivation. The Chlorella cells only secreted tryptophan rather than aromatic proteins during axenic cultivation. N-dodecanoyl-l-homoserine lactone (C12-HSL) was correlated with the flocculation activity and extracellular protein content of bioflocs during fed-batch cultivation. The addition of exogenous C12-HSL enhanced the flocculation activity of the Chlorella-bacteria system and aromatic protein production in the EPS. Chlorella cells sensed exogenous C12-HSL and significantly upregulated the aromatic protein synthesis pathway during axenic cultivation. In addition, vanillin as a quorum-sensing inhibitor suppressed the positive effect of C12-HSL on flocculation activity and aromatic protein production and synthesis. This result indicated that vanillin intercepts the response of Chlorella cells to C12-HSL. Overall, C12-HSL is supposed to be an important signal molecule to achieve communication between Chlorella and Gram-negative bacteria and subsequently induce Chlorella cells to produce aromatic proteins for biofloc formation.

Microalgal flocculation and sedimentation: spatiotemporal evaluation of the effects of the pH and calcium concentration

The high cost of harvesting microalgae is a major hurdle for the microalgae industry, and an efficient pre-concentration method is required. In this study, the effects of using different pH values (between pH 3 and 11) and calcium (Ca²⁺) concentrations (between 0 and 5 mM) on Chlorella vulgaris sedimentation were investigated by evaluating the spacio-temporal distributions of microalgae cells. Fast and efficient sedimentation occurred (within 10 min) at a high Ca²⁺ concentration (5 mM) at pH 9 and 11. However, the sediment volume was lower at a Ca²⁺ concentration of 3 mM than at a Ca²⁺ concentration of 5 mM. This indicated that the Ca²⁺ concentration strongly affected the sediment volume. Fast sedimentation and a low sediment volume were found at pH 7 and a Ca²⁺ concentration of 5 mM, probably because of the neutral charge in the system (adhesion to calcium precipitates would have occurred at a high pH). The highest Ca²⁺ recovery (82%) was achieved when sediment produced at pH 11 and a Ca²⁺ concentration of 5 mM was acidified to pH 3.

A Novel Salt-Bridge Electroflocculation Technology for Harvesting Microalgae

Microalgae biomass, as a promising alternative feedstock, can be refined into biodiesel, pharmaceutical, and food productions. However, the harvesting process for quality biomass still remains a main bottleneck due to its high energy demand. In this study, a novel technique integrating alkali-induced flocculation and electrolysis, named salt-bridge electroflocculation (SBEF) with non-sacrificial carbon electrodes is developed to promote recovery efficiency and cost savings. The results show that the energy consumption decreased to 1.50 Wh/g biomass with a high harvesting efficiency of 90.4% under 300 mA in 45 min. The mean particle size of algae flocs increased 3.85-fold from 2.75 to 10.59 µm, which was convenient to the follow-up processing. Another major advantage of this method is that the salt-bridge firmly prevented cells being destroyed by the anode’s oxidation and did not bring any external contaminants to algal biomass and flocculated medium, which conquered the technical defects in electro-flocculation. The proposed SBEF technology could be used as a low cost process for efficient microalgae harvest with high quality biomass.

Cyanobacterial biorefinery: Towards economic feasibility through the maximum valorization of biomass

Cyanobacteria are well known for their plethora of applications in the fields of food industry, pharmaceuticals and bioenergy. Their simple growth requirements, remarkable growth rate and the ability to produce a wide range of bio-active compounds enable them to act as an efficient biorefinery for the production of valuable metabolites. Most of the cyanobacteria based biorefineries are targeting single products and thus fails to meet the efficient valorization of biomass. On the other hand, multiple products recovering cyanobacterial biorefineries can efficiently valorize the biomass with minimum to zero waste generation. But there are plenty of bottlenecks and challenges allied with cyanobacterial biorefineries. Most of them are being associated with the production processes and downstream strategies, which are difficult to manage economically. There is a need to propose new solutions to eliminate these tailbacks so on to elevate the cyanobacterial biorefinery to be an economically feasible, minimum waste generating multiproduct biorefinery. Cost-effective approaches implemented from production to downstream processing without affecting the quality of products will be beneficial for attaining economic viability. The integrated approaches in cultivation systems as well as downstream processing, by simplifying individual processes to unit operation systems can obviously increase the economic feasibility to a certain extent. Low cost approaches for biomass production, multiparameter optimization and successive sequential retrieval of multiple value-added products according to their high to low market value from a biorefinery is possible. The nanotechnological approaches in cyanobacterial biorefineries make it one step closer to the goal. The current review gives an overview of strategies used for constructing self-sustainable- economically feasible- minimum waste generating; multiple products based cyanobacterial biorefineries by the efficient valorization of biomass. Also the possibility of uplifting new cyanobacterial strains for biorefineries is discussed.

Latest Expansions in Lipid Enhancement of Microalgae for Biodiesel Production: An Update

Research progress on sustainable and renewable biofuel has gained motion over the years, not just due to the rapid reduction of dwindling fossil fuel supplies but also due to environmental and potential energy security issues as well. Intense interest in microalgae (photosynthetic microbes) as a promising feedstock for third-generation biofuels has grown over recent years. Fuels derived from algae are now considered sustainable biofuels that are promising, renewable, and clean. Therefore, selecting the robust species of microalgae with substantial features for quality biodiesel production is the first step in the way of biofuel production. A contemporary investigation is more focused on several strategies and techniques to achieve higher biomass and triglycerides in microalgae. The improvement in lipid enhancement in microalgae species by genetic manipulation approaches, such as metabolic or genetic alteration, and the use of nanotechnology are the most recent ways of improving the production of biomass and lipids. Hence, the current review collects up-to-date approaches for microalgae lipid increase and biodiesel generation. The strategies for high biomass and high lipid yield are discussed. Additionally, various pretreatment procedures that may aid in lipid harvesting efficiency and improve lipid recovery rate are described.

Microalgae harvesting techniques: updates and recent technological interventions

Microalgal biomass has garnered attention as a renewable and sustainable resource for producing biodiesel. The harvesting of microalgal biomass is a significant bottleneck being faced by the industries as it is the crucial cost driver in the downstream processing of biomass. Bioharvesting of microalgal biomass mediated by: microbial, animal, and plant-based polymeric flocculants has gained a higher probability of utility in accumulation due to: its higher dewatering potential, less toxicity, and ecofriendly properties. The present review summarizes the key challenges and the technological advancements associated with various such harvesting techniques. The economic and technical aspects of different microalgal harvesting techniques, particularly the cationic polymeric flocculant-based harvesting of microalgal biomass, are also discussed. Furthermore, interactions of flocculants with microalgal biomass and the effects of these interactions on metabolite and lipid extractions are discussed to offer a promising solution for suitability in selecting the most efficient and economical method of microalgal biomass harvesting for cost-effective biodiesel production.

Constructed microalgal-bacterial symbiotic (MBS) system: Classification, performance, partnerships and perspectives

The microalgal-bacterial symbiotic (MBS) system shows great advantages in the synchronous implementation of wastewater treatment and nutrient recovery. To enhance the understanding of different MBS systems, this review summarizes reported MBS systems and proposes three patterns according to the living state of microalgae and bacteria. They are free microalgal-bacterial (FMB) system, attached microalgal-bacterial (AMB) system and bioflocculated microalgal-bacterial (BMB) system. Compared with the other two patterns, BMB system shows the advantages of microalgal biomass harvesting and application. To further understand the microalgal-bacterial partnerships in the bioflocculation of BMB system, this review discusses bioflocs characteristics, extracellular polymeric substances (EPS) properties and production, and the effect of microalgae/bacteria ratio and microalgal strains on the formation of bioflocculation. Microalgal biomass production and application are important for BMB system development in the future. Food processing wastewater characterized by high biodegradability and low toxicity should be conducive for microalgal cultivation. In addition, exogenous addition of functional bacteria for nutrient removal and bioflocculation formation would be a crucial research direction to facilitate the large-scale application of BMB system.

Biocomposites Using Whole or Valuable Component-Extracted Microalgae Blended with Polymers: A Review

Global demand for plastics has increased steadily alongside industrial development. Despite their versatility and convenience, environmental pollution caused by plastics are a major issue. With a reduction in the market size of plastics being seemingly impossible, bioplastics may become key to tackle this issue. Among a wide range of sources of bioplastics, microalgae have come into the limelight. While abundant and valuable components in microalgae have the potential to replace preexisting plastics, complex processes and low cost performances have prevented them from entering the market. In this study, we examined techniques for biocomposites in which polymers are blended with microalgae. We focused on microalgae-based biocomposite blending processed from the perspective of functionality and cost performance.

Predicting biomass and hydrocarbon productivities and colony size in continuous cultures of Botryococcus braunii showa

Mathematical models were developed to predict biomass and hydrocarbon productivities and colony size (ouputs) of Botryococcus braunii showa cultures based on light intensity, temperature and dilution rate (inputs). These models predicted the following maximum values: biomass productivity, 1.3 g L^-1 d^-1; hydrocarbon productivity, 1.5 mg L^-1 d^-1; colony size, 320 µm under different culture conditions respectively. These values were confirmed experimentally. Additionally, the combination of inputs that simultaneously maximize all the possible outputs combinations were determined. The prediction for biomass-hydrocarbon-colony size were 1 g L^-1 d^-1, 12.05 mg L^-1 d^-1 and 156.8 µm respectively; biomass productivity-hydrocarbon productivities: 1 g L^-1 d^-1 and 13.94 mg L^-1 d^-1 respectively; biomass productivity-colony size: 1 g L^-1 d^-1 and 172.8 µm respectively; hydrocarbon productivity-colony size: 9 mg L^-1 d^-1 and 240 µm respectively. All these predictions were validated experimentally. These models might be very useful to implement a Botryococcus braunii showa large scale production.

Use of ultrasound for aiding lipid extraction and biodiesel production of microalgae harvested by chitosan

In this work, chitosan, a biodegradable flocculant, was investigated to determine its utility in flocculating microalgae, its effect on cell integrity, and its impact on lipid extraction and the conversion to fatty acid methyl ester (FAME). Results showed that chitosan adequately performed flocculation on Chlorella vulgaris microalgae and achieved a high harvesting efficiency of 96.35 ± 1.96% when implemented under the following conditions: chitosan dose = 120 mg/L^-1, pH = 5, mixing speed = 150 rpm for 20 min, followed by 10 min of settling time. Moreover, scanning electron microscope (SEM) combined with transmission electron microscope (TEM) demonstrated that chitosan protected the cells' structure from morphological damage. Finally, the highest lipid extraction yield and biodiesel production was obtained from the chitosan-harvested biomass when the microalgae were pretreated with ultrasound.

Key Targets for Improving Algal Biofuel Production

A number of technological challenges need to be overcome if algae are to be utilized for commercial fuel production. Current economic assessment is largely based on laboratory scale up or commercial systems geared to the production of high value products, since no industrial scale plant exits that are dedicated to algal biofuel. For macroalgae (‘seaweeds’), the most promising processes are anaerobic digestion for biomethane production and fermentation for bioethanol, the latter with levels exceeding those from sugar cane. Currently, both processes could be enhanced by increasing the rate of degradation of the complex polysaccharide cell walls to generate fermentable sugars using specifically tailored hydrolytic enzymes. For microalgal biofuel production, open raceway ponds are more cost-effective than photobioreactors, with CO2 and harvesting/dewatering costs estimated to be ~50% and up to 15% of total costs, respectively. These costs need to be reduced by an order of magnitude if algal biodiesel is to compete with petroleum. Improved economics could be achieved by using a low-cost water supply supplemented with high glucose and nutrients from food grade industrial wastewater and using more efficient flocculation methods and CO2 from power plants. Solar radiation of not <3000 h·yr−1 favours production sites 30° north or south of the equator and should use marginal land with flat topography near oceans. Possible geographical sites are discussed. In terms of biomass conversion, advances in wet technologies such as hydrothermal liquefaction, anaerobic digestion, and transesterification for algal biodiesel are presented and how these can be integrated into a biorefinery are discussed.

Glycine betaine grafted nanocellulose as an effective and bio-based cationic nanocellulose flocculant for wastewater treatment and microalgal harvesting

Flocculation is a widely used technology in industry including for wastewater treatment and microalgae harvesting. To increase the sustainability of wastewater treatment, and to avoid contamination of the harvested microalgal biomass, there is a need for bio-based flocculants to replace synthetic polymer flocculants or metal salt coagulants. We developed the first cellulose nanocrystalline flocculant with a grafted cationic point charge, i.e. glycine betaine (i.e. N,N,N-trimethylglycine) grafted cellulose nanocrystals (CNCs) effective for the flocculation of kaolin (a model system for wastewater treatment), the freshwater microalgae Chlorella vulgaris, and the marine microalgae Nannochloropsis oculata. We successfully grafted glycine betaine onto CNCs using a one-pot reaction using a tosyl chloride activated esterification reaction with a degree of substitution ranging from 0.078 ± 0.003 to 0.152 ± 0.002. The degree of substitution is controlled by the reaction conditions. Flocculation of kaolin (0.5 g L^-1) required a dose of 2 mg L^-1, a comparable dose to commercial polyacrylamide-based flocculants. Flocculation was also successful for freshwater as well as marine microalgae (biomass concentration about 300 mg L^-1 dry matter), although the flocculation efficiency of the latter remained below 80%. The dose to induce flocculation (DS = 0.152 ± 0.002) was 20 mg L^-1 for the freshwater Chlorella vulgaris and 46 mg L^-1 for the marine Nannochloropsis oculata, comparable to other bio-based flocculants such as chitosan or TanFloc.

Microalgal bio-flocculation: present scenario and prospects for commercialization

The need for sustainable production of renewable biofuel has been a global concern in the recent times. Overcoming the tailbacks of the first- and second-generation biofuels, third-generation biofuel using microalgae as feedstock has emerged as a plausible alternative. It has an added advantage of preventing any greenhouse gas (GHG) emissions with simultaneous carbon dioxide sequestration. Dewatering of microalgal culture is one of the many concerns regarding industrial-scale biofuel production. The small size of microalgae and dilute nature of its growth cultures creates huge operational cost during biomass separation, limiting economic feasibility of algae-based fuels. Considering the recovery efficiency, operation economics, technological feasibility and cost-effectiveness, bio-flocculation is a promising method of harvesting. Moreover, advantage of bio-flocculation over other conventional methods is that it does not incur the addition of any external chemical flocculants. This article reviews the current status of bio-flocculation technique for harvesting microalgae at industrial scale. The various microbial strains that can be prospective bioflocculants have been reviewed along with its application and advantages over chemical flocculants. Also, this article proposes that the primary focus of an appropriate harvesting technique should depend on the final utilization of the harvested biomass. This review article attempts to bring forth the beneficial aspects of microbial aided microalgal harvesting with a special attention on genetically modified self-flocculation microalgae.

Towards green extraction methods from microalgae learning from the classics

Microalgae started receiving attention as producers of third generation of biofuel, but they are rich in many bioactive compounds. Indeed, they produce many molecules endowed with benefic effects on human health which are highly requested in the market. Thus, it would be important to fractionate algal biomass into its several high-value compounds: this represents the basis of the microalgal biorefinery approach. Usually, conventional extraction methods have been used to extract a single class of molecules, with many side effects on the environment and on human health. The development of a green downstream platform could help in obtaining different class of molecules with high purity along with low environmental impact. This review is focused on technical advances that have been performed, from classic methods to the newest and green ones. Indeed, it is fundamental to set up new procedures that do not affect the biological activity of the extracted molecules. A comparative analysis has been performed among the conventional methods and the new extraction techniques, i.e., switchable solvents and microwave-assisted and compressed fluid extractions.

Towards a better understanding of microalgae natural flocculation mechanisms to enhance flotation harvesting efficiency

In microalgae harvesting, flocculation is usually a compulsory preliminary step to further separation by sedimentation or flotation. For some microalgae species, and under certain growth conditions, flocculation can occur naturally. Natural flocculation presents many advantages as it does not require the addition of any flocculants to the culture medium and shows high efficiency rate. But because natural flocculation is so specific to the species and conditions, and thanks to the knowledge accumulated over the last years on flocculation mechanisms, researchers have developed strategies to induce this natural harvesting. In this review, we first decipher at the molecular scale the underlying mechanisms of natural flocculation and illustrate them by selected studies from the literature. Then we describe the developed strategies to induce natural flocculation that include the use of biopolymers, chemically modified or not, or involve mixed species cultures. But all these strategies need the addition of external compounds or microorganism which can present some issues. Thus alternative directions to completely eliminate the need for an external molecule, through genetic engineering of microalgae strains, are presented and discussed in the third part of this review.

Effective Harvesting of Nannochloropsis Microalgae Using Mushroom Chitosan: A Pilot-Scale Study

For efficient downstream processing, harvesting remains as one of the challenges in producing Nannochloropsis biomass, a microalga with high-value omega-3 oils. Flocculation is an effective, low-energy, low-cost method to harvest microalgae. Chitosan has been shown to be an effective food-grade flocculant; however, commercial chitosan is sourced from crustaceans, which has disadvantages including concerns over heavy-metal contamination. Thus, this study tests the flocculation potential of mushroom chitosan. Our results indicate a 13% yield of chitosan from mushroom. The identity of the prepared chitosan was confirmed by Fourier-transform infrared (FTIR) spectroscopy. Furthermore, results show that mushroom chitosan can be an alternative flocculant with >95% flocculation efficiency when tested in 100-mL jar and 200-L vertical column photobioreactor. Applications in a 2000-L raceway pond demonstrated that thorough mixing of mushroom chitosan with the algal culture is required to achieve efficient flocculation. With proper mixing, mushroom chitosan can be used to produce food-grade Nannochloropsis biomass suitable for the production of vegan omega-3 oils as a fish oil alternative.

Harvesting of marine microalgae using cationic cellulose nanocrystals

Flocculation of marine microalgae is challenging because of the high ionic strength of the culture medium. We investigated cationic cellulose nanocrystals (CNCs) as biobased flocculants for the marine microalgae Nannochloropsis oculata, and compared its performance to chitosan. Cationic CNCs induced flocculation at a low dose of 11 mg L^-1, while chitosan required a dose of 35 mg L^-1. Our cationic CNCs possess a permanent positive charge, allowing flocculation over a wide pH-range (4 to 10). The CNC maximum flocculation efficiency was 90 %, while chitosan achieved > 95 %, attributed to small flocs remaining in suspension for CNCs. However, centrifugation for 1 min at 180 g or gravity filtration using a 30 μm nylon filter after CNC flocculation resulted in the removal of these small, stable flocs (∼150 μm diam) and > 95% harvesting efficiency. Cationic CNCs can thus serve as a sustainable alternative natural flocculant for harvesting both freshwater and marine microalgae.

A comprehensive review on cultivation and harvesting of microalgae for biodiesel production: Environmental pollution control and future directions

Biodiesel is one of the best promising candidates in response to the energy crisis, since it has the capability to minimize most of the environmental problems. Microalgae, as the feedstock of third-generation biodiesel, are considered as one of the most sustainable resources. However, microalgae production for biodiesel feedstock on a large scale is still limited, because of the influences of lipid contents, biomass productivities, lipid extraction technologies, the water used in microalgae cultivation and processes of biomass harvesting. This paper firstly reviews the recent advances in microalgae cultivation and growth processes. Subsequently, current microalgae harvesting technologies are summarized and flocculation mechanisms are analyzed, while the characteristics that the ideal harvesting methods should have are summarized. This review also summarizes the environmental pollution control performances and the key challenges in future. The key suggestions and conclusions in the paper can offer a promising roadmap for the cost-effective biodiesel production.

Effect of shear rate on floc characteristics and concentration factors for the harvesting of Chlorella vulgaris using coagulation-flocculation-sedimentation

Coagulation-based separation has been increasingly applied to microalgal harvesting because of its competitive cost and high scalability. The characteristics of flocs formed during coagulation/flocculation are critical for efficient harvesting. However, few studies have been devoted to systematically investigating the structural characteristics of microalgal flocs and their influences on subsequent settling performance. In this paper, the dynamic mean size and fractal dimension, strength, regrowth and settling performance of Al³⁺ coagulated Chlorella vulgaris flocs were characterized at various flocculation shear rates. The influence of shear rate on floc characteristics was revealed. An appropriate shear rate (9 s^-1) produced more desirable microalgal flocs (in terms of size and compactness), with better settling performance and a higher concentration factor, than higher or lower shear rates, favoring their separation and subsequent harvesting. At this condition, the concentration factor reached 13.50, which was a 177.21% improvement over the 4.87 reached at a low shear rate.

Efficient microalgae harvesting using a thermal flotation method with response surface methodology

Thermal pre-flocculation to enable dispersed air flotation is an economical and ecofriendly technology for harvesting microalgae from water. However, the underlying mechanism and optimal conditions for this method remain unclear. In this study, Chlorella vulgaris (C. vulgaris) and Scenedesmus obliquus (S. obliquus) were harvested using a thermal flotation process. The surface structure and characteristics (morphology, electricity, and hydrophobicity) of the microalgae were analyzed using FT-IR (Fourier transform infrared spectroscopy), SEM (scanning electron microscopy), zeta potential, and a hydrophobic test. Further, response surface methodology (RSM) was used to optimize the flotation process. The hydrophobicity of S. obliquus exceeded that of C. vulgaris; as such, under the thermal pre-flocculation, S. obliquus (88.16%) was harvested more efficiently than C. vulgaris (47.16%). Thermal pre-flocculation denatured the lipids, carbohydrate, and proteins of microalgal cell surfaces. This resulted in a decrease in the electrostatic repulsion between the cells and air bubbles. The highest harvesting efficiency was 91.96% at 70 °C, 1,412 rpm, and 13.36 min. The results of this study demonstrate the potential for economic and ecofriendly harvesting of microalgae for biofuels and other bioproducts industries.

Application of the CRISPR/Cas system for genome editing in microalgae

Microalgae are arguably the most abundant single-celled eukaryotes and are widely distributed in oceans and freshwater lakes. Moreover, microalgae are widely used in biotechnology to produce bioenergy and high-value products such as polyunsaturated fatty acids (PUFAs), bioactive peptides, proteins, antioxidants and so on. In general, genetic editing techniques were adapted to increase the production of microalgal metabolites. The main genome editing tools available today include zinc finger nucleases (ZFNs), transcriptional activator-like effector nucleases (TALENs), and the clustered regularly interspaced short palindromic repeats (CRISPR)/Cas nuclease system. Due to its high genome editing efficiency, the CRISPR/Cas system is emerging as the most important genome editing method. In this review, we summarized the available literature on the application of CRISPR/Cas in microalgal genetic engineering, including transformation methods, strategies for the expression of Cas9 and sgRNA, the CRISPR/Cas9-mediated gene knock-in/knock-out strategies, and CRISPR interference expression modification strategies.

The potential of a natural biopolymeric flocculant, ε-poly-L-lysine, for harvesting Chlorella ellipsoidea and its sustainability perspectives for cost and toxicity

The successful production of microalgal biomass requires the precise coordination of many different steps. Cell harvesting is a central process in all methods currently used for the production of microalgal biomass. Therefore, improving the harvesting process itself, and using a harvesting method that is compatible with adjacent steps, is necessary to prevent problems that may occur during downstream processing. This study examined the potential of the cationic biopolymer ε-poly-L-lysine (ε-PLL) for use in the harvest of microalgae (Chlorella ellipsoidea). The effects of ε-PLL concentration and mixing intensity on flocculation efficiency and operating costs were determined. We found that ε-PLL was not toxic to microalgal cells at concentrations of up to 25 mg/L, based on the photosystem II quantum yield. A recovery rate of 95% was achieved using 19 mg/L ε-PLL, and the estimated harvest cost was 20 US$/ton of harvested biomass. Moreover, ε-PLL displayed antimicrobial properties, leaving the harvested biomass intact and pure. Therefore, the use of ε-PLL-induced flocculation appears to be an attractive option when harvesting microalgal biomass for use as low- and high-value commodities for humans or animals.

Flocculating properties and potential of Halobacillus sp. strain H9 for the mitigation of Microcystis aeruginosa blooms

Microcystis aeruginosa can cause harmful algal blooms in freshwaters worldwide. It has already seriously affected human lives and prevented the use of water resources. Therefore, there is an urgent need to develop ecofriendly and effective methods to control and eliminate M. aeruginosa in aquatic environments. In this study, Halobacillus sp. strain H9, a bacterium that showed high M. aeruginosa flocculation activity, was isolated and selected to assess its potential for the removal of M. aeruginosa. The analyses of flocculation activity and mode indicated that the strain H9 induced M. aeruginosa flocculation by secreting active flocculating substance rather than by directly contacting algal cells. A 5% concentration of the H9 supernatant could efficiently flocculate M. aeruginosa cells with a density of up to 5 × 10⁷ cells/mL. Dramatic increases in the zeta potential indicated that charge neutralization could be the mechanism of the flocculation process. The strain H9 flocculated M. aeruginosa with no damage to the algal cell membrane, and did not result in microcystin being released into the surrounding environment. The flocculated algal culture was less toxic to zebrafish larvae, suggesting an environmentally friendly benefit of the H9 supernatant. In addition to M. aeruginosa, the H9 strain was also able to flocculate two other species causing harmful algal blooms, Phaeocystis globose and Heterosigma akashiwo. Furthermore, the flocculation activity of the H9 supernatant was stable at different temperatures and over a wide pH range. These characteristics give the H9 strain great potential for mitigating the influences of harmful algal blooms.

A review on chemical mechanism of microalgae flocculation via polymers

•

Mechanism involved in microalgal flocculation has been reviewed.

•

Commercially, bioflocculation is suitable and cost-effective.

•

Organic & inorganic flocculants and their features are covered.

•

Ideal proportion amongst flocculants and biomass decides their efficiency.

Industrially, harvesting of the microalgal biomass is a techno-economic tailback, which essentially meant for the algal biomass industry. It is considered energy as well as cost-intensive in view of the fact that the dewatering process during harvesting. In this review chemical reactions involved in the flocculation of microalage biomass via various certain principal organic polymers are focused. Besides, it focuses on natural biopolymers as flocculants to harvest the cultivated microalgae. Commercially, bio-flocculation is suitable and cost-effective in the midst of a range of adopted harvesting techniques and the selection of an appropriate bioflocculant depends on its efficacy on the several microalgae strains like potential biomass fixation, ecological stride and non-perilous nature. The harvesting of toxin free microalgae biomass in large quantity by such flocculants can be considered to be one of the most cost-effective performances towards sustainable biomass recovery.

Efficient Harvesting of Nannochloropsis Microalgae via Optimized Chitosan-Mediated Flocculation

Food-grade rather than synthetic or chemical flocculants are needed for microalgae harvesting by settling, if used for food products. Chitosan is effective in harvesting freshwater microalgae, but it is expensive and typically not suitable for marine microalgae like Nannochloropsis. To minimize costs for food-grade flocculation, a number of potentially important parameters are considered, including chitosan solubility and optimized chitosan-mediated flocculation of Nannochloropsis sp. BR2 by a five-factor central composite design experiment. Results show that an optical density (440 nm) of 2 (0.23 g dry weight L-1), initial pH of 6, final pH of 10, and 22 ppm chitosan with a viscosity of 1808 cP provide optimum flocculation efficiency, which is predicted to be in the range of 97.01% to 99.93%. These predictions are verified on 4.5 and 8 L Nannochloropsis sp. BR2 cultures.

Harvesting of Microalgae by Flocculation

Due to increasing demands for microalgal biomass and products originating from microalgae, large-scale production systems are necessary. However, current microalgal production technologies are not cost-effective and are hindered by various bottlenecks, one of which is the harvesting of microalgal biomass. Cell separation is difficult because of the low sedimentation velocity of microalgae, their colloidal character with repelling negative surface charges, and low biomass concentrations in culture broths; therefore, large volumes need to be processed in order to concentrate the cells. Flocculation is considered to be one of the most suitable methods for harvesting microalgal biomass. This article provides an overview of flocculation methods suitable for microalgal harvesting, their mechanisms, advantages and drawbacks. Special attention is paid to the role of surface charge in the mechanism of flocculation. The novelty of the review lies in the interconnection between the context of technological applications and physico-chemical surface phenomena.

Environmental evaluation of flocculation efficiency in the separation of the microalgal biomass of Scenedesmus sp. cultivated in full-scale photobioreactors

In this paper the environmental evaluation of the separation process of the microalgal biomass Scenedesmus sp. from full-scale photobioreactors was carried out at the Research and Development Nucleus for Sustainable Energy (NPDEAS), with different flocculants (iron sulfate - FeCl₃, sodium hydroxide - NaOH, calcium hydroxide - Ca(OH)² and aluminum sulphate Al₂(SO₄)₃, by means of the life cycle assessment (LCA) methodology, using the SimaPro 7.3 software. Furthermore, the flocculation efficiency by means of optical density (OD) was also evaluated. The results indicated that FeCl₃ and Al₂(SO₄)₃ were highly effective for the recovery of microalgal biomass, greater than 95%. Though, when FeCl₃ was used, there was an immediate change in color to the biomass after the orange colored salt was added, typical with the presence of iron, which may compromise the biomass use according to its purpose and Al₂(SO₄)₃ is associated with the occurrence of Alzheimer's disease, restricting the application of biomass recovered through this process for nutritional purposes, for example. Therefore, it was observed that sodium hydroxide is an efficient flocculant, promoting recovery around 93.5% for the ideal concentration of 144 mg per liter. It had the best environmental profile among the compared flocculant agents, since it did not cause visible changes in the biomass or compromise its use and had less impact in relation to acidification, eutrophication, global warming and human toxicity, among others. Thus, the results indicate that it is important to consider both flocculation efficiency aspects and environmental impacts to identify the best flocculants on an industrial scale, to optimize the process, with lower amount of flocculant and obtain the maximum biomass recovery and decrease the impact on the extraction, production, treatment and reuse of these chemical compounds to the environment. However, more studies are needed in order to evaluate energy efficiency of the process coupled with other microalgal biomass recovery technologies. In addition, studies with natural flocculants, other polymers and changes in pH are also needed, as these are produced in a more sustainable way than synthetic organic polymers and have the potential to generate a biomass free of undesirable contaminants.

Nutrient removal and biomass production: advances in microalgal biotechnology for wastewater treatment

Owing to certain drawbacks, such as energy-intensive operations in conventional modes of wastewater treatment (WWT), there has been an extensive search for alternative strategies in treatment technology. Biological modes for treating wastewaters are one of the finest technologies in terms of economy and efficiency. An integrated biological approach with chemical flocculation is being conventionally practiced in several-sewage and effluent treatment plants around the world. Overwhelming responsiveness to treat wastewaters especially by using microalgae is due to their simplest photosynthetic mechanism and ease of acclimation to various habitats. Microalgal technology, also known as phycoremediation, has been in use for WWT since 1950s. Various strategies for the cultivation of microalgae in WWT systems are evolving faster. However, the availability of innovative approaches for maximizing the treatment efficiency, coupled with biomass productivity, remains the major bottleneck for commercialization of microalgal technology. Investment costs and invasive parameters also delimit the use of microalgae in WWT. This review critically discusses the merits and demerits of microalgal cultivation strategies recently developed for maximum pollutant removal as well as biomass productivity. Also, the potential of algal biofilm technology in pollutant removal, and harvesting the microalgal biomass using different techniques have been highlighted. Finally, an economic assessment of the currently available methods has been made to validate microalgal cultivation in wastewater at the commercial level.

Harvesting and contamination control of microalgae Chlorella ellipsoidea using the bio-polymeric flocculant α-poly-l-lysine

Microalgae have been extensively studied for the production of various products. However, to date, microalgal biomass has not become economically feasible, mainly due to different issues such as contamination from various sources that occurs during downstream processes, and which leads to low quality biomass with limited application. In this study, to overcome contamination by flocculants and other microorganisms, the cationic biopolymer α-Poly-l-lysine (α-PLL) was applied. The cationic amine moiety and polymeric chain of α-PLL rendered microalgal harvesting efficient. With increasing α-PLL chain length, efficient dose- and time-dependent harvesting was achieved. In addition to efficient flocculation performance, biomass harvested using α-PLL showed suppressed biological contamination through the inherent antimicrobial activity of α-PLL. Thus, it is possible to upgrade the quality and storability of produced microalgal biomass using α-PLL-induced flocculation.

Microalgae Chlorella vulgaris biomass harvesting by natural flocculant: effects on biomass sedimentation, spent medium recycling and lipid extraction

BACKGROUND

Microalgal biomass harvesting using traditional chemicals is costly for the production of biofuels, hindering the scale-up process of the technology. Thus, the search for a cost-effective microalgal harvesting method is extremely important. Using chitosan as a natural flocculant to harvest microalgal biomass seems to be an efficient and convenient solution. Although microalgal biomass flocculation by chitosan has been reported in some previous studies, literature on the harvesting of microalgae C. vulgaris biomass using such polymer is scanty. In addition, there is limited information available on whether the usage of chitosan during the harvesting will affect downstream lipid extraction. Still, whether microalgae can be re-grown with the spent medium after chitosan flocculation is still unknown.

RESULTS

In this study, microalgal biomass harvesting using chitosan as a natural flocculant and aluminum sulfate as a traditional flocculant was compared and evaluated. Optimal doses and effects on biomass sedimentation, spent medium recycling and lipid extraction were investigated. The results showed that the optimal doses for chitosan and aluminum sulfate to achieve more than 90% biomass recovery were 0.25 and 2.5 g/L, respectively. The sedimentation time of 10 min was found to be the most appropriate to remove over 90% biomass from culture. The spent medium after chitosan flocculation could be potentially recycled for the re-cultivation of microalgae, which demonstrated robust growth in comparison with those grown in the recycled medium from aluminum sulfate flocculation. The lipid content of microalgae harvested by chitosan reached 32.9, 4.6% higher than that of those harvested by aluminum sulfate, indicating that the application of the natural flocculant would not impact the downstream extraction of microalgal lipids.

CONCLUSION

The results herein presented, demonstrated that chitosan is applicable for microalgal harvesting during the upscaling process. Flocculation method developed by using chitosan as a natural flocculant is a worthy microalgal harvesting method for microalgae-based biofuel production. There is hope that chitosan can be reasonably and technically realistically applied in a full-scale process for the harvesting of microalgal biomass.

A biorefinery for Nannochloropsis: Induction, harvesting, and extraction of EPA-rich oil and high-value protein

Microalgae have been studied as biofactories for almost four decades. Yet, even until today, many aspects of microalgae farming and processing are still considered exploratory because of the uniqueness of each microalgal species. Thus, it is important to develop the entire process of microalgae farming: from culturing to harvesting, and down to extracting the desired high-value products. Based on its rapid growth and high oil productivities, Nannochloropsis sp. is of particular interest to many industries for the production of high-value oil containing omega-3 fatty acids, specifically eicosapentaenoic acid (EPA), but also several other products. This review compares the various techniques for induction, harvesting, and extraction of EPA-rich oil and high-value protein explored by academia and industry to develop a multi-product Nannochloropsis biorefinery. Knowledge gaps and opportunities are discussed for culturing and inducing fatty acid biosynthesis, biomass harvesting, and extracting EPA-rich oil and high-value protein from the biomass of Nannochloropsis sp.

Bioflocculation: An alternative strategy for harvesting of microalgae - An overview

Microalgae based research has been extensively progressed for the production of value added products and biofuels. Potential application of microalgae for biofuel is recently gained more attention for possibilities of biodiesel and other high value metabolites. However, high cost of production of biomass associated with harvesting technologies is one of the major bottleneck for commercialization of algae based industrial product. Based on the operation economics, harvesting efficiency, technological possibilities, flocculation of algal biomass is a superior method for harvesting microalgae from the growth medium. In this article, latest trends of microalgal cell harvesting through flocculation are reviewed with emphasis on current progress and prospect in environmental friendly bio-based flocculation approach. Bio-flocculation based microalgae harvesting technologies is a promising strategy for low cost microalgal biomass production for various applications.