Effects of Ca2+ on activity restoration of the damaged anammox consortium

The adaptive regulation mechanism of Anammox granule sludge under calcium ions stress: Defense modes transformation

Anammox granular sludge (AnGS) has received considerable attention due to its low carbon footprint (less aeration energy and carbon source consumption) and high biomass density, but growth rate and stability are still the bottlenecks of AnGS process. Calcium ion (Ca2+) is essential for the growth of anaerobic ammonium oxidation bacteria (AnAOB) and plays an important role in the formation and stability of AnGS. Response of AnGS to Ca2+ under different concentrations was comprehensively investigated by multi-spectral and metagenomics analysis in four aspects: nitrogen removal performance, surface morphology, extracellular polymeric substance (EPS) composition and characterization, and microbial community. The nitrogen removal efficiency was significantly enhanced at appropriate Ca2+ concentration (2 mmol/L), owning to the more favorable morphology and functional microbial composition of AnGS. However, the nitrogen removal performance of AnGS declined with the Ca2+concentration increased from 2 to 8 mmol/L, due to the negative effects of excess Ca2+on EPS, mass transfer efficiency, and functional microorganisms. Meanwhile, an unexpected slight "rebound" of nitrogen removal efficiency was observed at Ca2+ = 6 mmol/L and attributed to the defense mode transformation of AnGS (from "ion stabilization" to "precipitate shield" modes) against excess Ca2+ stress. Based on the findings, the response mechanism of AnGS to Ca2+ with different concentrations was established. Our results enhanced the understanding of the interaction between AnGS and Ca2+, which may be valuable for filling the theoretical gap in enhancing the granulation and stability of AnGS and providing a reference for the practical operation of the AnGS process.

Roles of red mud-based biochar carriers in the recovery of anammox activity: characteristics and mechanisms

Anaerobic ammonium oxidation (anammox) sludge is easily deactivated in the process of treating ammonia-laden wastewater. To investigate an effective recovery method, red mud-based biochar carriers (RMBC) were prepared and added to a deactivated anammox reactor; the operation of this reactor had been interrupted for 6 months with starvation and low temperature. The deactivated sludge with added RMBC was recovered rapidly after 31 days, with the specific anammox activity rapidly increasing to 0.84 g N/(g VSS∙day), and the recovery efficiency of nitrogen removal rate increased by four times compared to the unadded control. The granulation degree and extracellular polymeric substances secretion of the anammox sludge with the added RMBC were significantly higher than that of the control group. In addition, a large number of spherical anammox bacteria were observed moored at the porous channels of RMBC, and the copy numbers of functional genes of anammox bacteria were approximately twice that of the control group. Hence, RMBC is a potential sludge activator, and it can provide a "house" to protect anammox bacteria, enhance the metabolic activity and the agglomerative growth of anammox bacteria, and synergistically achieve rapid recovery of deactivated anammox sludge.

Polydopamine and calcium functionalized fiber carrier for enhancing microbial attachment and Cr(VI) resistance

The formation of biofilm determines the performance and stability of biofilm system. Increasing the hydrophilicity of the carrier surface could efficiently accelerate the attachment and growth of microorganisms. Here, the surface of polypropylene (PP) fiber carrier was modified with polydopamine (PDA) and calcium (Ca(II)) to enhance microbial attachment and toxicity resistance. The results of surface characteristic confirmed the self-polymerization of PDA and the chelation mechanism of Ca(II). Subsequently, the biofilm formation experiments were conducted in sequencing batch biofilm reactors using both normal and chromium-containing wastewater. The biofilm on the surface of the modified carrier exhibited better nitrogen removal and Cr(VI) reduction ability. The biomass of the modified carrier was significantly increased, and the maximum microbial attachment amounts in normal wastewater and chrome-containing wastewater were 1153.34 and 511.78 mg/g carrier, respectively. Furthermore, the confocal laser scanning microscope (CLSM) indicated that the modified carrier coated with PDA and Ca(II) were both biocompatible, and the cell activity was significantly increased. 16S rRNA sequencing results showed that the modified carrier efficiently enriched both denitrification bacteria (Thauera and Flavobacterium) and chrome-reducing bacteria (Simplicispira and Arenimonas) to improve system stability and Cr(VI) resistance. Microbial phenotype prediction based on BugBase analysis further verified the enrichment effect of modified carriers on microorganisms responsible for biofilm formation and oxidative stress resistance. Overall, this work proposed a novel functional carrier that could provide references for advancing the application of biofilm systems in wastewater treatment.

Efficient nitrogen removal and robustness enhancement of a two-stage partial nitrification-anammox (PN/A) process with low sludge concentration for mature landfill leachate

The biological treatment system for high-strength wastewater, particularly landfill leachate, typically requires high sludge concentration to maintain nitrogen removal performance. However, it frequently causes an excessive accumulation of toxins in microbial metabolism, resulting in unstable performance during long-term operation. An efficient two-stage partial nitrification/anammox (PN/A) mature landfill leachate process with low sludge concentration was constructed by settling time reduction and Ca2+ addition. The ammonia removal rate reached 46.7 mg N/(L·h) in PN-SBR. Nitrosomonas (2.0%) was the sole genus responsible for partial nitrification. The influent NO2--N/NH4+-N of A-SBR was kept at 1.39, leading to a dynamic equilibrium of anammox and denitrification. Ca. Brocadia recovered fastest (0.32% → 1.8%) among the detected AnAOB genera. The process achieved NRE of 95.0% with effluent TIN of 37.6 mg/L (<40 mg/L). This research offered recommendations for the favorable operation of the two-stage PN/A mature landfill leachate treatment system with low sludge concentration.

A critical review of exogenous additives for improving the anammox process

Anammox achieves chemoautotrophic nitrogen removal under anaerobic and anoxic conditions and is a low-carbon wastewater biological nitrogen removal process with broad application potential. However, the physiological limitations of AnAOB often cause problems in engineering applications, such as a long start-up time, unstable operation, easily inhibited reactions, and difficulty in long-term strain preservation. Exogenous additives have been considered an alternative strategy to address these issues by retaining microbes, shortening the doubling time of AnAOB and improving functional enzyme activity. This paper reviews the role of carriers, biochar, intermediates, metal ions, reaction substrates, redox buffers, cryoprotectants and organics in optimizing anammox. The pathways and mechanisms of exogenous additives, which are explored to solve problems, are systematically summarized and analyzed in this article according to operational performance, functional enzyme activity, and microbial abundance to provide helpful information for the engineering application of anammox.

Differences in the Effects of Calcium and Magnesium Ions on the Anammox Granular Properties to Alleviate Salinity Stress

Divalent cations were known to alleviate salinity stress on anammox bacteria. Understanding the mechanism of reducing the salinity stress on anammox granules is essential for the application of the anammox process for saline wastewater treatment. In this study, the effect of Ca2+ and Mg2+ augmentation on the recovery of the activity of freshwater anammox granules affected by salinity stress was evaluated. At the condition of a salinity stress of 5 g NaCl/L, the specific anammox activity (SAA) of the granule decreased to 50% of that of the SAA without NaCl treatment. Augmentation of Ca2+ at the optimum concentration of 200 mg/L increased the SAA up to 78% of the original activity, while the augmentation of Mg2+ at the optimum concentration of 70 mg/L increased the SAA up to 71%. EPS production in the granules was increased by the augmentation of divalent cations compared with the granules affected by salinity stress. In the soluble EPS, the ratio of protein to polysaccharides was higher in the granules augmented by Ca2+ than with Mg2+, and the functional groups of the EPS differed from each other. The amount of Na+ sequestered in the soluble EPS was increased by the augmentation of divalent cations, which seems to contribute to the alleviation of salinity stress. Ca. Kuenenia-like anammox bacteria, which were known to be salinity stress-tolerant, were predominant in the granules and there was no significant difference in the microbial community of the granules by the salinity stress treatment. Our results suggest that the alleviation effect of the divalent cations on the salinity stress on the anammox granules might be associated with the increased production of different EPS rather than in changes to the anammox bacteria.

Unravelling the importance of Ca2+ and Mg2+ as essential in anammox culture medium

The mechanism and nitrogen removal performance of anammox process under different concentrations of Ca²⁺ and Mg²⁺ were explored from the perspective of molecular biology analysis based on the metabolic changes of the second messenger cyclic diguanylate (c-di-GMP). After 100-day operation, reactor with 98 mg/L Ca²⁺ and 30 mg/L Mg²⁺ achieved a higher anammox performance with an average total nitrogen (TN) removal efficiency of 85.8%. Under the Mg²⁺concentration of 30 mg/L, a higher Ca²⁺ could accelerate anammox process by promoting the amplification of Candidatus Brocadia (0.62%) and production of Diguanylate cyclase (DGC-s: 6.54 × 10⁸ copies/μL DNA) which function was to synthesize c-di-GMP. While under the Ca²⁺concentration of 49 mg/L, Mg²⁺ concentration at appropriate rang could promote the degradation process of c-di-GMP. Since Ca²⁺ had positive linear relationship with TN removal (R² = 0.96), a higher Ca²⁺ concentration is recommended in the culture medium. This study provided a potential method for optimization of anammox process.

Linear anionic surfactant (SDBS) destabilized anammox process through sludge disaggregation and metabolic inhibition

The increase of emerging contaminants, such as surfactants, is one of the major challenges to biological wastewater treatment. However, the potential impact of linear alkylbenzene sulphonates (LAS), a major class of anionic surfactants, on anammox process is unclear. The long-term effects of sodium dodecyl benzene sulfonate (SDBS, as a model LAS) on reactor performance, microbial community and sludge properties were investigated in this study. The presence of 5 mg L^-1 SDBS promoted the release of extracellular microbial products from anammox granules and the wash-out of anammox population via effluent. Despite sludge disaggregation, the reactor performance was robust to the exposure of 5 mg L^-1 SDBS due to functional redundancy. With the further increase of SDBS to 10 mg L^-1, the metabolic activity of anammox biomass and the transcription and post-translation of hydrazine dehydrogenase were significantly decreased. The potential mechanism might be associated with the damage on cell membrane that induced the leakage of intracellular matrix. These results highlight the need to consider the potential risk of LAS to operation of anammox process in biological wastewater treatment plant.

Deciphering the microbial and genetic responses of anammox biogranules to the single and joint stress of zinc and tetracycline

The feasibility of using anaerobic ammonium oxidation (anammox) process to treat wastewaters containing antibiotics and heavy metals was evaluated in this study. The nitrogen removal performance and characteristic parameters were monitored during the whole experimental period of 258 d. The single and joint effects of zinc and tetracycline on the microbial community were studied in upflow anaerobic sludge blanket (UASB) reactors. The anammox performance remained at levels comparable with the initial state at the lower inhibitor concentrations (zinc, 0-2.26 mg L^-1; tetracycline, 0-0.5 mg L^-1). When the concentrations of zinc and tetracycline increased to 3.39 mg L^-1 in R₁ and 1.0 mg L^-1 in R₂, an obvious deterioration in performance was observed. Dual inhibitors with a total concentration of ≥3 mg L^-1 caused dramatic decreases in the nitrogen removal efficiency of R₃. The quantification results showed that the abundances of eight antibiotic resistance genes (ARGs), czcA and intI1 in the experimental reactors generally increased under stress from metals or/and antibiotics, with final values higher than in the control, while the functional gene abundances were lower. Moreover, most genes exhibited significant correlations. Microbial community analysis indicated that Planctomycetes (represented by Candidatus Kuenenia) was inhibited by both zinc and tetracycline, but still held the dominant position. Furthermore, Caldilinea (belonging to Chloroflexi) maintained a higher abundance during the inhibitory period, implying its potential resistance to both inhibitors. These findings suggested that anammox could be inhibited by metals and antibiotics, but it has the potential to remove nitrogen from wastewaters containing both of them within the concentration threshold.

Fate of dissolved organic nitrogen during the Anammox process using ultra-high resolution mass spectrometry

Anaerobic ammonium oxidation (Anammox) is a cost-effective process for treating highly nitrogenous wastewater. However, the fate of organic nitrogen during Anammox treatment is still unclear, which limits its practical application. In this work, the changes in the quality of dissolved organic nitrogen (DON) in coal liquefaction wastewater (CLW) during Anammox were studied in relation to its chemical composition, which was determined by Fourier-transform ion cyclotron resonance mass spectrometry (FT-ICR-MS). The molecular-level characterization of extracellular polymeric substances (EPS) in the Anammox sludge is also reported for the first time in this paper. The relative contribution of N-containing compounds to the total dissolved organic matter (DOM) determined by summating the normalized intensities exceeded 30%, highlighting the complexity of the nitrogenous compounds in the influent. Additionally, Anammox appeared to be better suited to removing DON compounds with fewer carbonyl or carboxyl groups, more aromatic structures, and higher oxidative properties. Lignin-like substances were verified as the predominant component of N-containing compounds in Anammox EPS, followed by protein and substances with condensed aromatic structures. DON compounds with higher degrees of saturation, lower molecular weight, and higher lignin-like properties were more prone to absorption by Anammox EPS. A series of microbe-mediated pathways were demonstrated to be responsible for DON biodegradation, which revealed the organic and inorganic nitrogen removal mechanisms in the Anammox reactor. The obtained results provide great support to the ongoing efforts to optimize the Anammox process.

Effects of Ca2+ Concentration on Anaerobic Ammonium Oxidation Reactor Microbial Community Structure

The anaerobic ammonium oxidation (anammox) reaction removes nitrogen from wastewater, the performance of which is influenced by Ca2+; however, the effect of Ca2+ on microbial community structure is unclear. Therefore, the effects of Ca2+ concentration on the treatment performance of an anammox reactor and microbial community structure of anammox sludge were investigated. Ca2+ concentration minimally influenced the removal efficiency of NO2−–N and NH4+–N, but substantially influenced total N removal. Changing the Ca2+ concentration (between 25 and 125 mg/L) caused the average removal rate of total nitrogen to fluctuate by 3.3 percentage points. There were five major bacterial phyla in the anammox sludge: Proteobacteria, Chloroflexi, Acidobacteria, Planctomycete, and Chlorobi. Microbiological analysis revealed that the genera Acidobacterium, Anaerolinea, and Denitratisoma were positively correlated with Ca2+ concentration, and improved treatment performance of the anammox reactor. Moreover, uncultured Chlorobi bacterium clone RUGL1-218 (GQ421108.1) and uncultured sludge bacterium A21b (KT182572.1) may be key microorganisms for the immobilization of anammox bacteria. These findings offer a theoretical basis for improved wastewater treatment using the anammox process.

Nitrogen Removal by Co-Immobilized Anammox and Ammonia-Oxidizing Bacteria in Wastewater Treatment

In wastewater treatment, an alternative to the widely used aerobic nitrification with subsequent anoxic denitrification method is the combination of nitration and anammox (AMX) in one system. This study focuses on the co-immobilization of AMX and ammonia-oxidizing bacteria into a polyvinyl alcohol (PVA) hydrogel, and its effective use in nitrogen removal (NR). The NR process was performed in nine consecutive, repeated batches. By optimizing the conditions of the biotransformations, there was equal utilization of nitrogen in both sources, N–NH4+ and N–NO2−, at 100% NR during the sixth repetition. A significant increase in the immobilized co-culture activity was also detected per cycle. The maximum value of the NR rate was 3.46 mg N (L h)−1, and 100% NR efficiency was achieved with an initial concentration of 100.3 mg N L−1 for N–NH4+ and 60.1 mg N L−1 for N–NO2−, during the eighth batch biotransformation.

Flow cytometry applications in water treatment, distribution, and reuse: A review

Ensuring safe and effective water treatment, distribution, and reuse requires robust methods for characterizing and monitoring waterborne microbes. Methods widely used today can be limited by low sensitivity, high labor and time requirements, susceptibility to interference from inhibitory compounds, and difficulties in distinguishing between viable and non-viable cells. Flow cytometry (FCM) has recently gained attention as an alternative approach that can overcome many of these challenges. This article critically and systematically reviews for the first time recent literature on applications of FCM in water treatment, distribution, and reuse. In the review, we identify and examine nearly 300 studies published from 2000 to 2018 that illustrate the benefits and challenges of using FCM for assessing source-water quality and impacts of treatment-plant discharge on receiving waters, wastewater treatment, drinking water treatment, and drinking water distribution. We then discuss options for combining FCM with other indicators of water quality and address several topics that cut across nearly all applications reviewed. Finally, we identify priority areas in which more work is needed to realize the full potential of this approach. These include optimizing protocols for FCM-based analysis of waterborne viruses, optimizing protocols for specifically detecting target pathogens, automating sample handling and preparation to enable real-time FCM, developing computational tools to assist data analysis, and improving standards for instrumentation, methods, and reporting requirements. We conclude that while more work is needed to realize the full potential of FCM in water treatment, distribution, and reuse, substantial progress has been made over the past two decades. There is now a sufficiently large body of research documenting successful applications of FCM that the approach could reasonably and realistically see widespread adoption as a routine method for water quality assessment.

Increased salinity improves the thermotolerance of mesophilic anammox consortia

While the application of anammox-based process for mesophilic sidestream treatment is at present the state of the art and mainstream treatment at ambient temperature is also in development, the feasibility of thermophilic anammox process is still unclear. This study investigated the effects of salinity on the thermotolerance of mesophilic anammox sludge. In batch activity tests, 45 °C seems to be the critical temperature for the tolerance of mesophilic anammox consortia without acclimatization or amendments. The optimal anammox activity at 40, 42.5, and 45 °C can be achieved with the amendment of salt at 5-8, 8-10, and ~12 g NaCl L^-1, respectively. However, this improvement effect was limited at 50 °C or when the shock duration was longer than 24 h even at 45 °C. In continuous-flow bioreactors, mesophilic anammox consortia could gradually adapt to 40-50 °C under a transition of 2.5 °C, and the performance was enhanced by an increase in salinity, which may be associated with the increase in extracellular polymeric substances. A nitrogen removal rate of 0.53 kgN m^-3 d^-1 was finally obtained at 50 °C. Overall, these interesting results facilitate further opportunities for thermophilic anammox process.

High rate nitrogen removal by ANAMMOX internal circulation reactor (IC) for old landfill leachate treatment

This study aimed to evaluate the performance of a high rate nitrogen removal lab-scale ANAMMOX reactor, namely Internal Circulation (IC) reactor, for old landfill leachate treatment. The reactor was operated with pre-treated leachate from a pilot Partial Nitritation Reactor (PNR) using a high nitrogen loading rate ranging from 2 to 10kgNm^-3d^-1. High rate removal of nitrogen (9.52±1.11kgNm^-3d^-1) was observed at an influent nitrogen concentration of 1500mgNL^-1. The specific ANAMMOX activity was found to be 0.598±0.026gN₂-NgVSS^-1d^-1. Analysis of ANAMMOX granules suggested that 0.5-1.0mm size granular sludge was the dominant group. The results of DNA analysis revealed that Candidatus Kueneniastuttgartiensis was the dominant species (37.45%) in the IC reactor, whereas other species like uncultured Bacteroidetes bacterium only constituted 5.37% in the system, but they were still responsible for removing recalcitrant organic matter.

Roles of EDTA washing and Ca²⁺ regulation on the restoration of anammox granules inhibited by copper(II)

We investigated the feasibility of using ethylene diamine tetraacetic acid (EDTA) washing followed by Ca(2+) enhancement for the recovery of anammox reactors inhibited by Cu(II). Kinetic experiments and batch activity assays were employed to determine the optimal concentration of EDTA and washing time; and the performance and physiological dynamics were tracked by continuous-flow monitoring to evaluate the long-term effects. The two-step desorption process revealed that the Cu in anammox granules was primarily introduced via adsorption (approximately, 80.5%), and the portion of Cu in the dispersible layer was predominant (accounting for 71.1%). Afterwards, the Cu internalized in the cells (approximately, 14.7%) could diffuse out of the cells and be gradually washed out of the reactor over the next 20 days. The Ca(2+) addition that followed led to an accelerated nitrogen removal rate recovery slope (0.1491 kgN m(-3) d(-2)) and a normal biomass growth rate (0.054 d(-1)). The nitrogen removal rate returned to normal levels within 90 days and gradual improvements in granular characteristics were also achieved. Therefore, this study provides a new insight that externally removing the adsorbed heavy metals followed by internally repairing the metabolic system may represent an optimal restoration strategy for anammox consortium damaged by heavy metals.

Bio-augmentation for mitigating the impact of transient oxytetracycline shock on anaerobic ammonium oxidation (ANAMMOX) performance

The feasibility of applying bio-augmentation tactics to remit the influence of transient oxytetracycline (OTC) shock on the anaerobic ammonium oxidation (ANAMMOX) process was evaluated. The bio-augmentation was applied together with shock test, with OTC shock concentration of 518 mg L(-1) and 1-h duration. 0.655-2.62 g volatile suspended solid (VSS) sludges were varied to optimize bio-augmentation dosage (BAD), and appropriate bio-augmentation time (BAT) was determined. The validity of the bio-augmentation was indicated by recovery performance and sludge characteristics. The restoring time of 38 h for bio-augmented reactor was shorter than that of non-bio-augmented reactor (45 h), and heme c content was increased respectively from 0.195 ± 0.001, 0.267 ± 0.047, 0.301 ± 0.049, to 0.340 ± 0.053 μmol g(-1) VSS with the BAD of 0.655, 1.31, 1.97, 2.62 g-VSS. The results suggest that bio-augmentation enhances the recovery of ANAMMOX performance following OTC shock and BAT and BAD are key operational factors.