Effects of ZnO nanoparticles on wastewater treatment and their removal behavior in a membrane bioreactor

Efficient chromium removal from leather industrial wastewater in batch experimental study: Green synthesis and characterization of zinc oxide nanoparticles using Ficus benghalensis extracts

The urgent need to address the severe environmental risk posed by chromium-contaminated industrial wastewater necessitates the development of eco-friendly cleanup methodologies. Utilizing the Ficus benghalensis plant extracts, the present study aims to develop green zinc oxide nanoparticles for the removal of Cr metal ions from wastewater. The leaves of Ficus benghalensis, often known as the banyan tree, were used to extract a solution for synthesizing ZnO NPs. These nanoparticles were developed with the goal of efficiently eliminating chromium (Cr) from industrial effluents. Batch studies were carried out to assess the efficiency of these synthesized ZnO NPs in treating leather industrial effluent, with aiming for optimal chromium removal. This involved measuring the nanoparticles' capacity to adsorb Cr ions from wastewater samples by comparing chromium levels before and after treatment. Removal efficiency for Cr was estimated through the batches such as optimization of pH, contact time, initial Cr concentration and sorbent dose of ZnO NPs were of the batches. These synthesized ZnO NPs were found to be successful in lowering chromium levels in wastewater to meet permissible limit. The nanoparticles exhibited their highest absorption capacity, reaching 94 % (46 mg/g) at pH 4, with a contact time of 7 hours with the optimum sorbent dose of 0.6 g/L. Hence, the excellent adsorption capabilities of these nanoparticles, together with their environmentally benign manufacturing technique, provide a long-term and efficient solution for chromium-contaminated wastewater treatment. Its novel nature has the potential to significantly improve the safety and cleanliness of water ecosystems, protecting the both i.e. human health and the environment.

Investigating the Effect of Bi2MoO6/g-C3N4 Ratio on Photocatalytic Degradation of Sulfadiazine under Visible Light

In this study, a series of Bi2MoO6/g-C3N4 composites were prepared through a wet-impregnation method, and their photocatalytic properties were investigated for the degradation of sulfadiazine (SDZ) under visible light irradiation. Physical and chemical characterizations were carried out using X-ray diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FT-IR), photoluminescence spectroscopy (PL), UV-vis diffuse reflectance spectra (UV-vis), and electrochemical impedance spectra (EIS). Compared to pure g-C3N4, the introduction of Bi2MoO6 significantly enhanced the visible light responsive photocatalytic activity, with the 1:32 Bi2MoO6/g-C3N4 composite exhibiting the highest photodegradation efficiency towards SDZ under visible light irradiation with a photocatalytic efficiency of 93.88% after 120 min of visible light irradiation. The improved photocatalytic activity can be attributed to the formation of a heterojunction between Bi2MoO6 and g-C3N4, which promotes the transfer of photogenerated electron-hole pairs, thereby elevating its photocatalytic activity. The results suggest that Bi2MoO6/g-C3N4 composites have potential application for the degradation of sulfonamides in aquatic environments.

Nanomaterials in membrane bioreactors: Recent progresses, challenges, and potentials

The use of nanomaterials (NMs) in the fabrication and modification of membranes as well as the coupling of nanomaterial-based processes with membrane processes have been attracted many researchers today. The NMs due to a wide range of types, different chemistry, the possibility of various kinds of functionality, different properties like antibacterial activity, hydrophilicity, and large surface area were applied to enhance the membrane properties. In the membrane bioreactors (MBRs) as a highly successful process of membrane technology in wastewater treatment, the NMs have been applied for improving the efficiency of MBR process. This review assessed the application of NMs both as the modifiers of membrane and as the effective part of hybrid techniques with MBR system for wastewater treatment. The efficiency of NMs blended membranes in the MBR process has been reviewed in terms of antifouling and antibacterial improvement and removal performance of the pollutants. Novel kinds of NMs were recognized and discussed based on their properties and advantages. The NMs-based photocatalytic and electrochemical processes integrated with MBR were reviewed with their benefits and drawbacks. In addition, the effect of the presence of mobilized NPs in the sludge on MBR performance was surveyed. As a result of this review, it can be concluded that nanomaterials generally improve MBR performance. The high flux and antifouling properties can be obtained by adding nanomaterials with hydrophilic and antibacterial properties to the membrane, and further studies are required for photocatalytic NMs applications. In addition, this review shows that the low amounts of NMs in the membrane structure could have an effective influence on the MBR process. Besides, since many studies in the literature are carried out at the laboratory scale, it is thought that pilot and real-scale studies should be carried out to obtain more reliable data.

Feedback mechanisms of periphytic biofilms to ZnO nanoparticles toxicity at different phosphorus levels

The increasing use of nanoparticles (NPs) has raised concerns about their potential environmental risks. Many researches on NPs focused on the toxicity mechanism to microorganisms, but neglect the toxicity effects in relation to nutritional conditions. Here, we evaluated the interactive effects of zinc oxide (ZnO) NPs and phosphorus (P) levels on the bacterial community and functioning of periphytic biofilms. Results showed that long-term exposure to ZnO NPs significantly reduced alkaline phosphatase activity (APA) of periphytic biofilms just in P-limited conditions. Co-occurrence network analysis indicated that ZnO NPs exposure reduced network complexity between bacterial taxa in P-limited conditions, while the opposite trend was observed in P-replete conditions. Correlation analysis and random forest modeling suggested that excessive Zn²⁺ released and high reactive oxygen species (ROS) production might be mainly responsible for the inhibition of APA induced by ZnO NPs under P-limited conditions, while adjustment of bacterial diversity and improvement of keystone taxa cooperation were the main mechanisms in maintaining APA when subjected to weak toxicity of ZnO NPs in P-replete conditions. Taken together, our results provide insights into the biological feedback mechanism involved in ZnO NPs exposure on the ecological function of periphytic biofilms in different P nutritional conditions.

Toxicity and combined effects of antibiotics and nano ZnO on a phosphorus-removing Shewanella strain in wastewater treatment

Antibiotics and nanoparticles, which are emerging contaminants, can occur simultaneously in biological wastewater treatment systems, potentially resulting in complex interactive effects. This study investigated the effects of individual and complex zinc oxide nanoparticles (nZnO) and antibiotics (quinolone and sulfonamide), on the Shewanella strain used to remove phosphorus (PO₄^3-), metabolic processes, as well as its complexing and toxicity mechanisms. The inhibition of PO₄^3- removal increased from 30.7% to 100.0% with increased nZnO concentrations (half maximal effective concentration (EC50) = 1.1 mg Zn/L) by affecting poly-p and glycogen metabolites. The combined exposure to nZnO and ciprofloxacin/norfloxacin (CIP/NOR) had a significant antagonistic effect on the removal of PO₄^3- and on the metabolism of poly-p and glycogen in phosphate-accumulating organisms (PAOs), whereas the complexing of sulfonamide and nZnO had no significant additional effect. Thus, the complexing of nanoparticles and antibiotics exhibited different toxicity effects from the antibiotic structure-based complex reactions. These results can be used to improve wastewater treatment processes and reduce risks associated with wastewater discharge.

Comparative toxicity of ionic and nanoparticulate zinc in the species Cymodoce truncata, Gammarus aequicauda and Paracentrotus lividus

Due to the continuous development, production and consumption of nanoparticles (NPs), their release, fate and effects in marine coastal environment can represent a major concern. The aim of this study was to evaluate the toxicity of ZnO nanoparticles (ZnO NPs) and compare it to bulk ZnSO4 on three macroinvertebrates: the isopod Cymodoce truncata (i.e. used for the first time in ecotoxicology), the amphipod Gammarus aequicauda and the sea urchin Paracentrotus lividus. This study showed concentration- and time-dependent relationships for all biological models for both ZnO NPs and ZnSO4. Both Zn forms elicited high toxicity to G. aequicauda and C. truncata juveniles, but ZnO NPs induced comparable responses to both species (96h-LC50 = 0.30 and 0.37 mg/L for G. aequicauda and C. truncata, respectively; p > 0.05), while differences were found after ZnSO4 exposure (96h-LC50 = 0.28 and 0.63 mg/L, respectively; p < 0.05). ZnO NPs generated sub-lethal effects on P. lividus embryos (72h-EC50 = 0.04 (0.03, 0.05) mg/L), not significantly different from ZnSO4 ones (72h-EC50 = 0.06 (0.05, 0.07) mg/L). Effects of ZnO NPs were similar to existing literature data for other testing species. C. truncata can be considered as a promising new biological model in (nano)ecotoxicology.

Structural and thermal properties of pure and chromium doped zinc oxide nanoparticles

Abstract

Pure ZnO and Cr-doped ZnO nanoparticles have been synthesized via a facile chemical co-precipitation route and their structural, thermal characteristics were discussed systematically. In the experimental producer, the doping concentration has varied the range, 0.05–0.1 M, while calcined at 600 °C. The influence of Cr-doping on the physical characteristics of ZnO nanoparticles was investigated and addressed. As-prepared samples were analyzed via XRD, FTIR, TGA/DTA, BET, and ICP-MS. XRD analysis shows that ZnO and Cr doped ZnO nanoparticles with average particle sizes between 23 and 39 nm were successfully developed with hexagonal wurtzite structure. The FTIR spectroscopy analysis confirms the existence of chromium in the doped ZnO nanoparticles and the formation of ZnO. The TGA/DTA analysis shows that Cr–ZnO nanoparticles are more thermally stable than ZnO nanoparticles. Moreover, the dopant concentration has been analyzed via ICP-MS and showed a good agreement with the expected chromium concentration. The BET surface area measurement shows that 176.25 m2/g and 287.17 m2/g for un-doped ZnO, and 0.1 M Cr-doped ZnO nanoparticles, respectively. Hence, doping of Cr enhances the surface area and thermal stability. Thus, Cr–ZnO nanoparticles show good thermal stability, and high surface area, which is an excellent characteristices of nanomaterials.

Graphic abstract

Insights into chronic zinc oxide nanoparticle stress responses of biological nitrogen removal system with nitrous oxide emission and its recovery potential

The nitrogen transformation performances and greenhouse gas nitrous oxide (N₂O) emissions in a sequencing batch reactor under chronic exposure to zinc oxide nanoparticles (ZnO NPs) were quantified and the system's self-recovery potentials were assessed. ZnO NPs posed a dose-dependent depression effect on the removal efficiencies of ammonia nitrogen (NH₄⁺-N) and total nitrogen (TN), and the N₂O emissions. The suppressed N₂O emissions had a positive relationship with the activity ratios of nitrite/NO reductases and N₂O reductase, and were expected to be caused by the inhibited heterotrophic denitrification process. The inhibition of glucose metabolism key enzymes and electron transport chain activities would be responsible for the heterotrophic denitrification performances deterioration. Furthermore, the removal efficiencies of NH₄⁺-N and TN were recovered to control levels through the nitrite-shunt. However, the N₂O emission increased significantly above the control during the recovery period mainly due to the irreversibility of the depressed nitrite oxidation activities.

Impacts of morphological-controlled ZnO nanoarchitectures on aerobic microbial communities during real wastewater treatment in an aerobic-photocatalytic system

This study aimed to evaluate the impacts of morphological-controlled ZnO nanoarchitectures on aerobic microbial communities during real wastewater treatment in an aerobic-photocatalytic system. Results showed that the antibacterial properties of ZnO nanoarchitectures were significantly more overwhelming than their photocatalytic properties. The inhibition of microbial activities in activated sludge by ZnO nanoarchitectures entailed an adverse effect on wastewater treatment efficiency. Subsequently, the 16S sequencing analysis were conducted to examine the impacts of ZnO nanoarchitectures on aerobic microbial communities, and found the significantly lower microbial diversity and species richness in activated sludge treated with 1D-ZnO nanorods as compared to other ZnO nanoarchitectures. Additionally, 1D-ZnO nanorods reduced the highest proportion of Proteobacteria phylum in activated sludge due to its higher proportion of active polar surfaces that facilitates Zn²⁺ ions dissolution. Pearson correlation coefficients showed that the experimental data obtained from COD removal efficiency and bacterial log reduction were statistically significant (p-value < 0.05), and presented a positive correlation with the concentration of Zn²⁺ ions. Finally, a non-parametric analysis of Friedman test and post-hoc analysis confirmed that the concentration of Zn²⁺ ions being released from ZnO nanoarchitectures is the main contributing factor for both the reduction in COD removal efficiency and bacterial log reduction.

Metagenomic analysis of the biotoxicity of titanium dioxide nanoparticles to microbial nitrogen transformation in constructed wetlands

Extensive use of titanium dioxide nanoparticles (TiO₂ NPs) in various products has increased the release of these particles into wastewater, posing potential environmental risks. As an ecological wastewater treatment facility, constructed wetland (CW) is an important sink of NPs. However, little is known about the effects of NPs on microbial nitrogen transformation and related genes in CWs. In this study, short-term (5 days) and long-term (60 days) exposure experiments were conducted to investigate the effect of TiO₂ NPs (0, 1, and 50 mg/L) on microbial nitrogen removal in CWs. The results showed that nitrogen removal efficiency was decreased by 35%-51% after long-term exposure to TiO₂ NPs. Metagenomic analysis further confirmed that TiO₂ NPs declined the relative abundance of functional genes and those enzyme encoding genes involved in the nitrogen metabolism pathway and glycolysis metabolism process. Furthermore, our data proved that the indigent glycolysis metabolism process resulted in the shortage of electron (NADH) and energy sources (ATP), causing inefficient nitrogen removal. Overall, these results revealed that the accumulation of TiO₂ NPs altered the genetic expression of biofilm in CWs, which had significant impacts on biological nitrogen transformation.

Feasibility of isolated novel facultative quorum quenching consortiums for fouling control in an AnMBR

Anaerobic membrane bioreactor (AnMBR) technology is being recognized as an appealing strategy for wastewater treatment, however, severity of membrane fouling inhibits its widespread implementations. This study engineered novel facultative quorum quenching consortiums (FQQs) coping with membrane fouling in AnMBRs with preliminary analysis for their quorum quenching (QQ) performances. Herein, Acyl-homoserine lactones (AHLs)-based quorum sensing (QS) in a lab-scale AnMBR initially revealed that N-Hexanoyl-dl-homoserine lactone (C6-HSL), N-Octanoyl-dl-homoserine lactone (C8-HSL) and N-Decanoyl-dl-homoserine lactone (C10-HSL) were the dominant AHLs in AnMBRs in this study. Three FQQs, namely, FQQ-C6, FQQ-C8 and FQQ-C10, were harvested after anaerobic screening of aerobic QQ consortiums (AeQQs) which were isolated by enrichment culture, aiming to degrade C6-HSL, C8-HSL and C10-HSL, respectively. Growth of FQQ-C6 and FQQ-C10 using AHLs as carbon source under anaerobic condition was significantly faster than those using acetate, congruously suggesting that their QQ performance will not be compromised in AnMBRs. All FQQs degraded a wide range of AHLs pinpointing their extensive QQ ability. FQQ-C6, FQQ-C8 and FQQ-C10 remarkably alleviated extracellular polymeric substances (EPS) production in a lab-scale AnMBR by 72.46%, 35.89% and 65.88%, respectively, and FQQ-C6 retarded membrane fouling of the AnMBR by 2 times. Bioinformatics analysis indicated that there was a major shift in dominant species from AeQQs to FQQs where Comamonas sp., Klebsiella sp., Stenotrophomonas sp. and Ochrobactrum sp. survived after anaerobic screening and were the majority in FQQs. High growth rate utilizing AHLs under anaerobic condition and enormous EPS retardation efficiency in FQQ-C6 and FQQ-C10 could be attributed to Comamonas sp.. These findings demonstrated that FQQs could be leveraged for QQ under anaerobic systems. We believe that this was the first work proposing a bacterial pool of facultative QQ candidates holding biotechnological promises for membrane fouling control in AnMBRs.

Size-dependent effects of ZnO nanoparticles on performance, microbial enzymatic activity and extracellular polymeric substances in sequencing batch reactor

ZnO nanoparticles (NPs) have been detected in various wastewater treatment plants. It is widely assumed that size has a crucial effect on the NPs toxicity. Concerns have been raised over probable size-dependent toxicity of ZnO NPs to activated sludge, which could eventually affect the treatment efficiencies of wastewater treatment facilities. The size-dependent influences of ZnO NPs on performance, microbial activities, and extracellular polymeric substances (EPS) from activated sludge were examined in sequencing batch reactor (SBR) in present study. Three different sizes (15, 50, and 90 nm) and five concentrations (2, 5, 10, 30, and 60 mg L^-1) were trialled. The inhibitions on COD and nitrogen removal were determined by the particle size, and smaller ZnO NPs (15 nm) showed higher inhibition effect than those of 50 and 90 nm, whereas the ZnO NPs with size of 50 nm showed maximum inhibition effect on phosphorus removal among three sizes of ZnO NPs. After exposure to different sized ZnO NPs, microbial enzymatic activities and removal rates of activated sludge represented the same trend, consistent with the nitrogen and phosphorus removal efficiency. In addition, apparent size- and concentration-dependent effects on EPS contents and components were also observed. Compared with the absence of ZnO NPs, 60 mg L^-1 ZnO NPs with sizes of 15, 50, and 90 nm increased the EPS contents from 92.5, 92.4, and 92.0 mg g^-1 VSS to 277.5, 196.8, and 178.2 mg g^-1 VSS (p < 0.05), respectively. The protein and polysaccharide contents increased with the decreasing particle sizes and increasing ZnO NPs concentrations, and the content of protein was always higher than that of polysaccharide.

Spatially Resolved Dissolution and Speciation Changes of ZnO Nanorods during Short-Term in Situ Incubation in a Simulated Wastewater Environment

Zinc oxide engineered nanomaterials (ZnO ENMs) are used in a variety of applications worldwide due to their optoelectronic and antibacterial properties with potential contaminant risk to the environment following their disposal. One of the main potential pathways for ZnO nanomaterials to reach the environment is via urban wastewater treatment plants. So far there is no technique that can provide spatiotemporal nanoscale information about the rates and mechanisms by which the individual nanoparticles transform. Fundamental knowledge of how the surface chemistry of individual particles change, and the heterogeneity of transformations within the system, will reveal the critical physicochemical properties determining environmental damage and deactivation. We applied a methodology based on spatially resolved in situ X-ray fluorescence microscopy (XFM), allowing observation of real-time dissolution and morphological and chemical evolution of synthetic template-grown ZnO nanorods (∼725 nm length, ∼140 nm diameter). Core-shell ZnO-ZnS nanostructures were formed rapidly within 1 h, and significant amounts of ZnS species were generated, with a corresponding depletion of ZnO after 3 h. Diffuse nanoparticles of ZnS, Zn₃(PO₄)₂, and Zn adsorbed to Fe-oxyhydroxides were also imaged in some nonsterically impeded regions after 3 h. The formation of diffuse nanoparticles was affected by ongoing ZnO dissolution (quantified by inductively coupled plasma mass spectrometry) and the humic acid content in the simulated sludge. Complementary ex situ X-ray absorption spectroscopy and scanning electron microscopy confirmed a significant decrease in the ZnO contribution over time. Application of time-resolved XFM enables predictions about the rates at which ZnO nanomaterials transform during their first stages of the wastewater treatment process.

Physicochemical and Biological Effects on Activated Sludge Performance and Activity Recovery of Damaged Sludge by Exposure to CeO2 Nanoparticles in Sequencing Batch Reactors

Recently, the growing release of CeO₂ nanoparticles (CeO₂ NPs) into sewage systems has attracted great concern. Several studies have extensively explored CeO₂ NPs' potential adverse impacts on wastewater treatment plants; however, the impaired activated sludge recovery potentials have seldom been addressed to date. To explore the physicochemical and biological effects on the activated sludge performance and activity recovery of damaged sludge by exposure to CeO₂ NPs in sequencing batch reactors (SBRs), four reactors and multiple indicators including water quality, key enzymes, microbial metabolites, the microbial community structure and toxicity were used. Results showed that 10-week exposure to higher CeO₂ NP concentration (1, 10 mg/L) resulted in a sharp decrease in nitrogen and phosphorus removal efficiencies, which were consistent with the tendencies of key enzymes. Meanwhile, CeO₂ NPs at concentrations of 0.1, 1, and 10 mg/L decreased the secretion of tightly bound extracellular polymeric substances to 0.13%, 3.14%, and 28.60%, respectively, compared to the control. In addition, two-week recovery period assays revealed that the functional bacteria Proteobacteria, Nitrospirae and Planctomycetes recovered slightly at the phyla level, as analyzed through high-throughput sequencing, which was consistent with the small amount of improvement of the effluent performance of the system. This reflected the small possibility of the activity recovery of damaged sludge.

Effects of ZnO nanoparticles on high-rate denitrifying granular sludge and the role of phosphate in toxicity attenuation

The increasing release of engineered nanoparticles (NPs) from consumer products has raised great concerns about their impacts on biological wastewater treatment. In this study, the widely-used ZnO NP was selected as a model NP to investigate its impact on high-rate denitrifying granular sludge in terms of sludge properties and community structure. A hormesis effect was observed during short-term exposure, in which the specific denitrification activity (SDA) was stimulated by 10% at 1 mg L^-1 ZnO NPs, but inhibited by 23% at 5.0 mg L^-1 ZnO NPs. When continuously exposed to 2.5 mg L^-1 ZnO NPs, the nitrogen removal capacity of the denitrification reactor was nearly deprived within 15 days, and the relative abundance of the dominant denitrifying bacterium (Castellaniella) was decreased from 51.0 to 8.0%. Meanwhile, the dehydrogenase activity (DHA) and the content of extracellular polymeric substance (EPS) significantly decreased to 22.3 and 61.1%, respectively. Nevertheless, the presence of phosphate substantially weakened the adverse effects of ZnO NPs on the SDA, EPS, DHA and the relative abundance of functional genes even exposed to 6.25 mg L^-1 ZnO NPs, which was associated with the fact that the level of Zn(II) released from ZnO NPs was significantly reduced in the presence of phosphate. Therefore, the toxicity of ZnO NPs may be mainly attributed to the release of toxic Zn(II) and could be attenuated in the presence of phosphate. Overall, this study provided further reference and meaningful insights into the impact of engineered NPs on biological wastewater treatment.

Effects of ZnO nanoparticles on the performance of anaerobic membrane bioreactor: An attention to the characteristics of supernatant, effluent and biomass community

Two laboratory-scale anaerobic membrane bioreactor (AnMBRs) were built to investigate the effect of zinc oxide nanoparticles (ZnO-NPs) on their performance, and the recovery phase was also examined. Results showed that the addition of ZnO-NPs with 0.4 mg/L caused significant deteriorations of AnMBR performance, including decrements of chemical oxygen demand (COD) removal efficiency from 96.4% to 81.5% and biogas production from 0.36 to 0 L/g COD removal within 40 days. A significant increment from 13.2 to 52.1 mg/L in soluble microbial products (SMP) was obtained, while no obvious effect on colloids was observed except an increased fluctuation of colloid concentration. Additionally, gas chromatography-mass spectrometry (GC-MS) analysis revealed remarkable changes of compounds in effluent with exposure to ZnO-NPs, and some new alkanes and esters were produced, such as Cyclobutane, 1,2-diethyl-, trans-, Tetradecane, Cyclopropane, octyl-, and Butanoic acid, methyl ester. The microbial community was compared using high-throughput sequencing, clearly showing the changes in both bacteria and archaea communities. Furthermore, results for recovery phase indicated that the AnMBR performance can be recovered within around 60 days after stopping ZnO-NPs addition, accompanied by the decrement of zinc concentration mainly adsorbed by sludge.

Development of a potential LPG sensor based on a PANI–Co3O4 nanocomposite that functions at room temperature

Nanostructured Co₃O₄ was synthesized by a sol–gel technique while 30% & 40% Co₃O₄–PANI (polyaniline) nanocomposites were successfully prepared employing an in situ polymerization technique.

Applications of membrane bioreactors for water reclamation: Micropollutant removal, mechanisms and perspectives

Membrane bioreactors (MBRs) have attracted attention in water reclamation as a result of the recent technical advances and cost reduction in membranes. However, the increasing occurrence of micropollutants in wastewaters has posed new challenges. Therefore, we reviewed the current state of research to identify the outstanding needs in this field. In general, the fate of micropollutants in MBRs relates to sorption, biodegradation and membrane separation processes. Hydrophobic, nonionized micropollutants are favorable in sorption, and the biological degradation shows higher efficiency at relatively long SRTs (30-40 days) and HRTs (20-30 h), as a result of co-metabolism, metabolism and/or ion trapping. Although the membrane rejection rates for micropollutants are generally minor, final water quality can be improved via combination with other technologies. This review highlights the challenges and perspectives that should be addressed to facilitate the extended use of MBRs for the removal of micropollutants in water reclamation.

Role of zinc oxide nanoparticles for effluent treatment using Pseudomonas putida and Pseudomonas aureofaciens

The biological treatment of textile effluent is enhanced by the use of zinc oxide (ZnO) nanoparticles for the reduction in chemical oxygen demand (COD) from its initial value of 1700 ppm. The present research investigated the effect of ZnO nanoparticles when microbial cultures of Pseudomonas putida and Pseudomonas aureofaciens were used to treat textile effluent in three-phase inverse fluidized bed bioreactor. The parameters like-size of ZnO nanoparticles, static bed height, superficial gas velocities and solid media particle size-together affected the COD reduction and all of these were investigated in this paper. ZnO nanoparticles of 280 nm reduced the maximum COD to 47 ppm (97.24%) at low gas velocity of 0.0027 m/s at 10% inoculum size and at a static bed height of 2.43 cm.

Evaluation of performance and microbial community successional patterns in an integrated OCO reactor under ZnO nanoparticle stress

An integrated OCO reactor was used to investigate the performance and microbial community successional changes under long-term exposure to relatively low levels of ZnO nanoparticles (NPs). Relatively higher concentrations of ZnO NPs (1.5 mg L⁻¹) could adversely affect the nitrogen and phosphorus removal in the reactor. The diversity and richness of the microbial communities chronically declined with an increasing concentration of ZnO NPs higher than 1.5 mg L⁻¹. With the elevated ZnO NPs, the phyla abundances of Proteobacteria, Firmicutes and Actinobacteria decreased slightly, whereas those of Bacteroidetes and Acidobacteria increased. Bacteroidetes and Proteobacteria were the predominant phyla in each phase (with a variation in abundance), together with some common taxa responses to ZnO NP stress as revealed by Venn diagram analysis. Some genera associated with the removal of nitrogen and phosphorus, such as Acinetobacter, Stenotrophomonas and Pseudomonas, decreased significantly. The present results are significant for expanding our understanding of the functional performance and microbial community successions of activated sludge which has experienced long-term exposure to environmentally relevant concentrations of ZnO NPs.

An integrated OCO reactor was used to investigate the performance and microbial community successional changes under a long-term exposure to relatively low-level ZnO nanoparticles (NPs).

Effect of zinc oxide nanoparticles on nitrogen removal, microbial activity and microbial community of CANON process in a membrane bioreactor

In this study, a membrane bioreactor (MBR) was adopted for completely autotrophic nitrogen removal over nitrite (CANON) process. Zinc oxide nanoparticles (ZnO NPs) was step-wise increased to analyze the influence on nitrogen removal, microbial activity and microbial communities. Finally ZnO NPs was removed to study its recovery capability. The bioactivities of ammonia-oxidizing bacteria (AOB), anaerobic ammonia-oxidizing bacteria (AAOB) and nitrite-oxidizing bacteria (NOB) were detected by batch experiments. Results showed that the ZnO NPs with low concentration (≤5mgL^-1) was profitable for nitrogen removal while the high concentration performed inhibition, and it lowered the abundance of both AOB and NOB while enhanced that of AAOB. ZnO NPs with high concentration (≥10mgL^-1) suppressed both AOB and AAOB, and long-term exposure within ZnO NPs led to microbial diversity decrease. The inhibition threshold of ZnO NPs on CANON process was 10mgL^-1, and the profitable concentration was 1mgL^-1.

Response of anaerobic membrane bioreactor to the presence of nano-Bi2WO6: reactor performance, supernatant characteristics, and microbial community

Considering the increasing incorporation of manufactured nano-material into consumer products, there is a concern about its potential impacts in biological wastewater treatment. In this study, the response of anaerobic sludge to the presence of Bi₂WO₆ nano-particles (NPs) was investigated in the anaerobic membrane bioreactor (AnMBR). As the concentration of Bi₂WO₆ in the reactor was controlled around 1 mg/L, there was no significant difference in effluent water quality or bacterial activities before and after NP exposure, partially due to the microbial-induced NP aggregation and stable complex formation. However, with the increasing dosage of Bi₂WO₆ from 5 to 40 mg/L, great influences on the AnMBR performance were observed, including the reduction of COD removal efficiency, inhibition of the mechanization step, increased production of soluble microbial products, and enhanced secretion of extracellular polymer substrates. Additional investigation with high-throughput sequencing was conducted, clearly demonstrating that Bi₂WO₆ NPs induced changes in the bacterial community.

Comparison of the effects and distribution of zinc oxide nanoparticles and zinc ions in activated sludge reactors

Zinc Oxide nanoparticles (ZnO NPs) are being increasingly applied in the industry, which results inevitably in the release of these materials into the hydrosphere. In this study, simulated waste-activated sludge experiments were conducted to investigate the effects of Zinc Oxide NPs and to compare it with its ionic counterpart (as ZnSO₄). It was found that even 1 mg/L of ZnO NPs could have a small impact on COD and ammonia removal. Under 1, 10 and 50 mg/L of ZnO NP exposure, the Chemical Oxygen Demand (COD) removal efficiencies decreased from 79.8% to 78.9%, 72.7% and 65.7%, respectively. The corresponding ammonium (NH₄⁺ N) concentration in the effluent significantly (P < 0.05) increased from 11.9 mg/L (control) to 15.3, 20.9 and 28.5 mg/L, respectively. Under equal Zn concentration, zinc ions were more toxic towards microorganisms compared to ZnO NPs. Under 50 mg/L exposure, the effluent Zn level was 5.69 mg/L, implying that ZnO NPs have a strong affinity for activated sludge. The capacity for adsorption of ZnO NPs onto activated sludge was found to be 2.3, 6.3, and 13.9 mg/g MLSS at influent ZnO NP concentrations of 1.0, 10 and 50 mg/L respectively, which were 1.74-, 2.13- and 2.05-fold more than under Zn ion exposure.

Effects of ZnO nanoparticles on aerobic denitrification by strain Pseudomonas stutzeri PCN-1

Anaerobic denitrification has been proved to be negatively affected by ZnO nanomaterials (NPs), but little is known about how ZnO NPs affects aerobic denitrification. In this study, inhibition of ZnO NPs to an aerobic denitrifier, Pseudomonas stutzeri PCN-1, was firstly reported. The results showed total nitrogen removal efficiency was decreased from 100% to 1.70% with the increase of ZnO NPs from 1 to 128mg/L. The presence of ZnO NPs caused significant inhibition of gene expressions and catalytic activities of nitrate reductase and nitrite reductase, which finally led to delayed nitrate reduction and high nitrite accumulation. Further studies revealed that the deposition of nanoparticles on the bacterial surface caused by electrostatic forces and the generation of reactive oxygen species (ROS) were responsible for the cytotoxicity of ZnO NPs, where ROS played a more important role. These results were of significance to evaluating the potential ecological toxicity and risks of nanomaterials.

Changes in nutrient removal and flocs characteristics generated by presence of ZnO nanoparticles in activated sludge process

The aim of this work was to evaluate the impact generated by ZnO NPs on the activated sludge process treating raw (RWW) and filtered wastewater (FWW). It was analyzed the oxygen uptake rate, nutrient removal, flocs characteristics and the morphological interactions between activated sludge and ZnO NPs, in presence of 450-2000 mg/L. The results showed that the presence of more than 450 mg/L of ZnO NPs in raw and filtered wastewater inhibited the oxygen uptake by activated sludge. The highest inhibition was 35% in presence of 1500 mg/L in RWW. The organic matter removal was only inhibited in the presence of 450 and 900 mg/L of ZnO NPs; while ammonia removal decreased for all concentrations of ZnO NPs in both types of wastewater, around 13% for RWW and up to 9% for FWW. The orthophosphate removal improved as the concentration of ZnO NPs increased for both wastewater types, enhancing up to 8% for RWW and 17% for FWW. The flocs size of activated sludge exposed to ZnO NPs in RWW decreased as the concentration of ZnO NPs increased; while for FWW, an opposite effect was observed. The elemental mapping allowed detect the Zn inside of microorganisms, which may correspond to a toxicity mechanism in RWW and FWW. These results indicated that the changes in nutrient removal and flocs characteristics caused by the presence of ZnO NPs on the activated sludge are related to wastewater characteristics, such as suspended solids, type of substrate and concentration of ZnO NPs.

Interactions and effects of metal oxide nanoparticles on microorganisms involved in biological wastewater treatment

To clarify the toxicological effects of metal oxide nanoparticles (NPs) on microorganisms with environmental relevance, it is necessary to understand their interactions. In this work, they were studied the effects and the morphological interactions of two metal oxide NPs (ZnO and TiO₂ ) with microorganisms, during aerobic treatment of wastewater. The effects were evaluated according to nutrient removal from wastewater, while morphological interactions were determined by three different techniques such as TEM, HAADF-STEM, as well as an elemental mapping. According to results about effects of both NPs, they inhibited the removal of organic matter and ammonia nitrogen, and enhanced the orthophosphate removal. Related to morphological interactions, the electron-dense material of both NPs was mainly observed bounded to cell membrane. In tests with ZnO NPs, it was also observed electron-dense material internalized in microorganisms without physical damage in cell membrane. The elemental mapping was useful to determine that the electron-dense material corresponded to Zn and Ti. Both interactions, internalization and attachment of NPs on cell membrane of microorganisms may trigger the negative effect in the removal of organic matter and nitrogen.

Comparison and distribution of copper oxide nanoparticles and copper ions in activated sludge reactors

Copper oxide nanoparticles (CuO NPs) are being increasingly applied in the industry which results inevitably in the release of these materials into the hydrosphere. In this study, simulated waste-activated sludge experiments were conducted to investigate the effects of Copper Oxide NPs at concentrations of 0.1, 1, 10 and 50 mg/L and to compare it with its ionic counterpart (CuSO₄). It was found that 0.1 mg/L of CuO NPs had negligible effects on Chemical Oxygen Demand (COD) and ammonia removal. However, the presence of 1, 10 and 50 mg/L of CuO NPs decreased COD removal from 78.7% to 77%, 52.1% and 39.2%, respectively (P < 0.05). The corresponding effluent ammonium (NH₄-N) concentration increased from 14.9 mg/L to 18, 25.1 and 30.8 mg/L, respectively. Under equal Cu concentration, copper ions were more toxic towards microorganisms compared to CuO NPs. CuO NPs were removed effectively (72-93.2%) from wastewater due to a greater biosorption capacity of CuO NPs onto activated sludge, compared to the copper ions (55.1-83.4%). The SEM images clearly showed the accumulation and adsorption of CuO NPs onto activated sludge. The decrease in Live/dead ratio after 5 h of exposure of CuO NPs and Cu²⁺ indicated the loss of cell viability in sludge flocs.

Effect of nano-ZnO on biogas generation from simulated landfills

Extensive use of nanomaterials in commercial consumer products and industrial applications eventually leads to their release to the waste streams and the environment. Nano-ZnO is one of the most widely-used nanomaterials (NMs) due to its unique properties. It is also known to impact biological processes adversely. In this study, the effect of nano-ZnO on biogas generation from sanitary landfills was investigated. Two conventional and two bioreactor landfills were operated using real MSW samples at mesophilic temperature (35°C) for a period of about 1year. 100mg nano-ZnO/kg of dry waste was added to the simulated landfill reactors. Daily gas production, gas composition and leachate Zn concentrations were regularly monitored. A model describing the fate of the nano-ZnO was also developed. The results obtained indicated that as much as 99% of the nano-ZnO was retained within the waste matrix for both reactor operation modes. Waste stabilization was faster in simulated landfill bioreactors with and without the addition of nano-ZnO. Moreover, the presence of the nano-ZnO within the waste led to a decrease in biogas production of about 15%, suggesting that the nano-ZnO might have some inhibitory effects on waste stabilization. This reduction can have potentially significant implications on waste stabilization and the use of biogas from landfills as a renewable energy source.

Effects of ZnO nanoparticle exposure on wastewater treatment and soluble microbial products (SMPs) in an anoxic-aerobic membrane bioreactor

The effect of zinc oxide nanoparticles (ZnO NPs) on the performance of an anoxic-aerobic submerged membrane bioreactor (MBR), and the characterization of the soluble microbial products (SMPs) produced in the presence of ZnO NPs was evaluated. Continuous operation over 144 days showed that ZnO NPs at concentrations of 10 and 50 mg/L exerted a negative impact on chemical oxygen demand (COD) and nitrogen removal, although ZnO NPs were efficiently removed in the MBR (>92%). 10 and 50 mg/L ZnO NPs decreased COD removal substantially from 93.1± 0.6% to 90.1± 0.8% (<0.05) and 86.3± 2.3% (<0.05), respectively. Similarly, with 10 and 50 mg L ZnO NPs, the decreased in NH₄N removal was 8.1% and 21.1%, respectively. Exposure to 1, 10 and 50 mg/L ZnO NPs increased SMP concentrations by 12.8%, 42.4% and 51.5%, respecti. High performance size exclusion chromatograph (HP-SEC) analysis revealed that the presence of ZnO NPs caused a significant increase in high-molecular weight (MW) (583 kDa) SMPs at 1 and 10 mg/L ZnO NP concentration. A substantial decrease in the concentration of high-MW compounds in the MBR effluent was observed at the end of the experiment. Excitation emission matrix (EEM) fluorescence contours revealed that SMPs were dominated by amino acid-, tryptophan protein-, polyaromatic-, and polycarboxylate-type substances. The presence of ZnO NPs enhanced the production of amino acid-like (7.5-25.1%) and tryptophan protein-like compounds (31.7-38.1%), compared to the control (6.0-20.2% for amino acid-like compounds; and 28.5-36.7% for tryptophan protein-like compounds). In contrast, the fulvic and humic acid-like compounds decreased with exposure to ZnO NPs. This work may help better understanding the effect of nanoparticle exposure on wastewater treatment performance and SMP characteristics.

Fabrication and Assessment of ZnO Modified Polyethersulfone Membranes for Fouling Reduction of Bovine Serum Albumin

ZnO/PES composite membranes were fabricated by phase inversion method using DMAc as a solvent. The structure of ZnO was investigated using TEM, SEM, XRD, and TGA. TEM images of ZnO nanoparticles were well-defined, small, and spherically shaped with agglomerated nanoparticles particles of 50 nm. The SEM and XRD results were an indication that ZnO nanoparticles were present in the prepared ZnO/PES composites membranes. Contact angle measurements were used to investigate surface structures of the composite membranes. The amount of ZnO nanoparticles on PES membranes was varied to obtain the optimal performance of the composite membranes in terms of pure water flux, flux recovery, and fouling resistance using the protein bovine serum albumin (BSA) as a model organic foulant. The results showed that addition of ZnO to PES membranes improved the hydrophilicity, permeation, and fouling resistance properties of the membranes. Pure water flux increased from a low of 250 L/m2h for the neat membrane to a high of 410 L/m2h for the composite membranes. A high flux recovery of 80–94% was obtained for the composite membranes. The optimal performance of the composite membranes was obtained at 1.5 wt% of ZnO.

The impact of zinc oxide nanoparticles on the bacterial microbiome of activated sludge systems

The expected growth in nanomaterial applications could result in increased amounts of nanoparticles entering municipal sewer systems, eventually ending up in wastewater treatment plants and therefore negatively affecting microbial populations and biological nutrient removal. The aim of this study was to ascertain the impact of zinc oxide nanoparticles (nZnO) on the bacterial microbiome of an activated sludge system. A metagenomic approach combined with the latest generation Illumina MiSeq platform and RDP pipeline tools were used to identify and classify the bacterial microbiome of the sludge. Results revealed a drastic decrease in the number of operational taxonomic units (OTUs) from 27 737 recovered in the nZnO-free sample to 23 743, 17 733, and 13 324 OTUs in wastewater samples exposed to various concentrations of nZnO (5, 10 and 100 mg/L nZnO, respectively). These represented 12 phyla, 21 classes, 30 orders, 54 families and 51 genera, completely identified at each taxonomic level in the control samples; 7-15-25-28-20 for wastewater samples exposed to 5 mg/L nZnO; 9-15-24-31-23 for those exposed to 10 mg/L and 7-11-19-26-17 for those exposed 100 mg/L nZnO. A large number of sequences could not be assigned to specific taxa, suggesting a possibility of novel species to be discovered.

Biofilms Versus Activated Sludge: Considerations in Metal and Metal Oxide Nanoparticle Removal from Wastewater

The increasing application of metal and metal oxide nanoparticles [Me(O)NPs] in consumer products has led to a growth in concentration of these nanoparticles in wastewater as emerging contaminants. This may pose a threat to ecological communities (e.g., biological nutrient removal units) within treatment plants and those subject to wastewater effluents. Here, the toxicity, fate, and process implications of Me(O)NPs within wastewater treatment, specifically during activated sludge processing and biofilm systems are reviewed and compared. Research showed activated sludge achieves high removal rate of Me(O)NPs by the formation of aggregates through adsorption. However, recent literature reveals evidence that inhibition is likely for nutrient removal capabilities such as nitrification. Biofilm systems were much less studied, but show potential to resist Me(O)NP inhibition and achieve removal through possible retention by sorption. Implicating factors during bacteria-Me(O)NP interactions such as aggregation, surface functionalization, and the presence of organics are summarized. At current modeled levels, neither activated sludge nor biofilm systems can achieve complete removal of Me(O)NPs, thus allowing for long-term environmental exposure of diverse biological communities to Me(O)NPs in streams receiving wastewater effluents. Future research directions are identified throughout in order to minimize the impact of these nanoparticles released.

Short and long term biosorption of silica-coated iron oxide nanoparticles in heterotrophic biofilms

The increased application of engineered nanoparticles (ENP) in industrial processes and consumer products has raised concerns about their impact on health and environmental safety. When ENP enter the global water cycle by e.g. wastewater streams, wastewater treatment plants (WWTP) represent potential sinks for ENP. During biological WWT, the attachment of ENP to biofilms is responsible for the desired removal of ENP from the water phase avoiding their release into the aquatic environment. However, the fundamental mechanisms guiding the interactions between ENP and biofilms are not yet fully understood. Therefore, this study investigates the behavior and biosorption of inorganic ENP, here magnetic iron oxide nanoparticles coated with silica (scFe3O4-NP), with heterotrophic biofilms at different time scales. Their magnetic properties enable to follow scFe3O4-NP in the biofilm system by a magnetic susceptibility balance and magnetic resonance imaging. Biofilms were exposed to scFe3O4-NP at short contact times (5 min) in flow cells and complementary, scFe3O4-NP were introduced into a moving bed biofilm reactor (MBBR) to be observed for 27 d. Mass balances revealed that scFe3O4-NP sorbed to the biofilm within a few minutes, but that the total biosorption was rather low (3.2 μg Fe/mg TSS). scFe3O4-NP mainly sorbed to the biofilm surface inducing the detachment of outer biofilm parts starting after an exposure time of 3h in the MBBR. The biosorption depended on the exposure concentration of scFe3O4-NP, but less on the contact time. Most scFe3O4-NP exited the flow cell (up to 65%) and the MBBR (57%) via the effluent. This effect was favored by the stabilization of scFe3O4-NP in the bulk liquid by organic matter leading to a low retention capacity of the MBBR system. The results contribute to improve our understanding about the fate of ENP in environmental and in technical biofilm systems and give indications for future investigations needed.

Response to shock load of engineered nanoparticles in an activated sludge treatment system: Insight into microbial community succession

The environmental impacts of the use of engineered nanoparticles (NPs) remain unclear and have attracted increasing concern worldwide. Considering that NPs eventually end up in wastewater treatment systems, the potential impact of ZnO and TiO2 NPs on the activated sludge was investigated using laboratory-scale sequencing batch reactors (SBRs). Short-term (24 h) exposure to 1, 10 and 100 mg/L shock loads of NPs reduced the oxygen uptake rate of the activated sludge by 3.55%-12.51% compared with the controls. In our experiment, the toxicities of TiO2 NPs were higher than those of ZnO NPs as reflected in the inhibition of oxygen utilization in the activated sludge. However, both the short-term (24 h) and long-term (21 days) exposure to ZnO and TiO2 NPs did not adversely affect the pollutant removal of the SBRs. Furthermore, the polymerase chain reaction-denaturing gel gradient electrophoresis revealed that the microbial community did not significantly vary after the short-term exposure (24 h) to 1, 10 and 100 mg/L shock loads of NPs; however, the cluster analysis in our experiment revealed that the slight difference caused by the NPs largely depended on exposure time rather than on NP type and NP concentration. The long-term exposure (13 days) to 10 mg/L shock load of ZnO or TiO2 NPs caused no substantial microbial community shifts in the activated sludge. The microbial diversity also showed no significant change when exposed to NPs as revealed by the Shannon-Wiener index.

Microbiote shift in sequencing batch reactors in response to antimicrobial ZnO nanoparticles

Zinc oxide nanoparticles (ZnO NPs) have been monitored in wastewater treatment plants as their potential adverse effects on functional microorganisms have been causing increasing concern.

Effects of CeO2 nanoparticles on system performance and bacterial community dynamics in a sequencing batch reactor

The effects of CeO2 nanoparticles (NPs) on the system performance and the bacterial community dynamics in a sequencing batch reactor (SBR) were investigated, along with the fate and removal of CeO2 NPs within the SBR. Significant impact was observed on nitrification; NH4+-N removal efficiency decreased from almost 100% to around 70% after 6 days of continuous exposure to 1.0 mg/L of CeO2 NPs, followed by a gradual recovery until a stable value of around 90% after 20 days. Additionally, CeO2 NPs also led to a significant increase in the protein content in the soluble microbial products, showing the disruptive effects of CeO2 NPs on the extracellular polymeric substance matrix and related activated sludge structure. Denaturing gradient gel electrophoresis analysis showed remarkable changes in the bacterial community structure in the activated sludge after exposure to CeO2 NPs. CeO2 NPs were effectively removed in the SBR mainly via sorption onto the sludge. However, the removal efficiency decreased from 95 to 80% over 30 days. Mass balance evaluation showed that up to 50% of the NPs were accumulated within the activated sludge and were removed with the waste sludge.

Low biosorption of PVA coated engineered magnetic nanoparticles in granular sludge assessed by magnetic susceptibility

When engineered nanoparticles (ENP) enter into wastewater treatment plants (WWTP) their removal from the water phase is driven by the interactions with the biomass in the biological treatment step. While studies focus on the interactions with activated flocculent sludge, investigations on the detailed distribution of ENP in other types of biomass, such as granulated sludge, are needed to assess their potential environmental pollution. This study employed engineered magnetic nanoparticles (EMNP) coated with polyvinyl alcohol (PVA) as model nanoparticles to trace their fate in granular sludge from WWT. For the first time, magnetic susceptibility was used as a simple approach for the in-situ quantification of EMNP with a high precision (error <2%). Compared to other analytical methods, the magnetic susceptibility requires no sample preparation and enabled direct quantification of EMNP in both the aqueous phase and the granular sludge. In batch experiments granular sludge was exposed to EMNP suspensions for 18 h. The results revealed that the removal of EMNP from the water phase (5-35%) and biosorption in the granular sludge were rather low. Less than 2.4% of the initially added EMNP were associated with the biomass. Loosely bounded to the granular sludge, desorption of EMNP occurred. Consequently, the removal of EMNP was mainly driven by physical co-sedimentation with the biomass instead of sorption processes. A mass balance elucidated that the majority of EMNP were stabilized by particulate organic matter in the water phase and can therefore likely be transported further. The magnetic susceptibility enabled tracing EMNP in complex matrices and thus improves the understanding of the general distribution of ENP in technical as well as environmental systems.

Long-term effects of engineered nanoparticles on enzyme activity and functional bacteria in wastewater treatment plants

The pervasive use of engineered nanoparticles (NPs) in a wide range of fields raises concerns about their potential environmental impacts. Previous studies confirmed that some NPs had already entered wastewater treatment plants (WWTPs). Wastewater nutrient removal depends on the metabolisms of activated sludge bacteria and their related key enzymes. Therefore, this study compared the possible influences of Al2O3, SiO2, TiO2, and ZnO NPs on the key enzymes activities and microbial community structures involved in wastewater treatment facilities. It was found that long-term exposure to these NPs significantly affected the microbial communities and changed the relative abundances of key functional bacteria, such as ammonia-oxidizing bacteria. Also, the gene expressions and catalytic activities of essential enzymes, such as ammonia monooxygenase, nitrite oxidoreductase, nitrate reductase, and nitrite reductase, were decreased, which finally resulted in a lower efficiency of biological nitrogen removal.