Fast microwave-assisted preparation of a low-cost and recyclable carboxyl modified lignocellulose-biomass jute fiber for enhanced heavy metal removal from water

Unrevealing the influence of reagent properties on disruption and digestibility of lignocellulosic biomass during alkaline pretreatment

Beyond the conventional consideration of pretreatment severity (PS) responsible for biomass disruption, the influence of reagent properties on biomass (LCB) disruption is often overlooked. To investigate the LCB disruption as a function of reagent properties, reagents with distinct cations (NaOH and KOH) and significantly higher delignification potential were chosen. NaOH solution (3 % w/v) with a measured pH of 13.05 ± 0.01 is considered the reference, against which a KOH solution (pH = 13.05 ± 0.01) was prepared for LCB pretreatment under the same PS. Despite comparable lignin content, varying glucose yield of NaOH (68.76 %) and KOH (46.88 %) pretreated residues indicated the presence of heterogeneously disrupted substrate. Holocellulose extracted from raw poplar (ASC, control) and alkaline pretreated residues (C-NaOH and C-KOH) were analyzed using HPLC, XRD, SEM, TGA/DTG, XPS, and 13CP MAS NMR to investigate the pretreatment-induced structural modification. Results revealed that, despite the same pretreatment severity, better disruption in C-NaOH (higher accessible fibril surface and less-ordered region) leading to higher digestibility than C-KOH, likely due to the smaller ionic radius of Na+, facilitates better penetration into dense LCB matrix. This study elucidates the importance of considering the reagent properties during LCB pretreatment, eventually enhancing consciousness while selecting reagents for efficient LCB utilization.

Adsorbents for water decontamination: A recycling alternative for fiber precursors and textile fiber wastes

The exponential growth in textile fiber production and commensurate release of textile waste-based effluents into the environment has significant impacts on human wellbeing and the long-term planetary health. To abate these negative impacts and promote resource circularity, efforts are being made to recycle these waste materials via conversion into adsorbents for water decontamination. This review critically examines plant- and regenerated cellulose-based fibers for removing water pollutants such as heavy metals, dyes, pharmaceutical and petrochemical wastes. The review reveals that chemical modification reactions such as grafting, sulfonation, carboxymethylation, amination, amidoximation, xanthation, carbon activation, and surface coating are normally employed, and the adsorption mechanisms often involve Van der Waals attraction, electrostatic interaction, complexation, chelation, ion exchange, and precipitation. Furthermore, the adsorption processes and thus the adsorption mechanisms are influenced by factors such as surface properties of adsorbents, pollutant characteristics including composition, porosity/pore size distribution, specific surface area, hydrophobicity/hydrophobicity, and molecular interactions. Besides, feasibility of the approaches in terms of handling and reuse, environmental fate, and economic impact was evaluated, in addition to the performances of the adsorbents, the prospects, and challenges. As current cost analysis is non-exhaustive, it is recommended that researchers focus on extensive cost analysis to fully appreciate the true cost effectiveness of employing these waste materials. In addition, more attention must be paid to potential chemical leaching, post-adsorption handling, and disposal. Based on the review, fiber precursors and textile fiber wastes are viable alternative adsorbents for sustainable water treatment and environmental management, and government entities must leverage on these locally accessible materials to promote recyclability and circularity.

Unveiling the performance of a novel alkalizing bacterium Enterobacter sp. LYX-2 in immobilization of available Cd

A novel alkalizing strain Enterobacter sp. LYX-2 that could resist 400 mg/L Cd was isolated from Cd-contaminated soil, which immobilized 96.05% Cd2+ from medium. Cd distribution analysis demonstrated that more than half of the Cd2+ was converted into extracellular precipitated Cd through mobilization of the alkali-producing mechanism by the strain LYX-2, achieving the high immobilization efficiency of Cd2+. Biosorption experiments revealed that strain LYX-2 had superior biosorption capacity of 48.28 mg/g for Cd. Pot experiments with Brassica rapa L. were performed with and without strain LYX-2. Compared to control, 15.92% bioavailable Cd was converted to non-bioavailable Cd and Cd content in aboveground vegetables was decreased by 37.10% with addition of strain LYX-2. Available Cd was mainly immobilized through extracellular precipitation, cell-surface biosorption and intracellular accumulation of strain LYX-2, which was investigated through Cd distribution, Scanning Electron Microscope and Energy-Dispersive X-ray Spectroscopy (SEM-EDS), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Photoelectron Spectroscopy (XPS) and Transmission Electron Microscopy (TEM) analysis. In addition, the application of strain LYX-2 significantly promoted the growth of vegetables about 2.4-fold. Above results indicated that highly Cd-resistant alkalizing strain LYX-2, as a novel microbial passivator, had excellent ability and reuse value to achieve the remediation of Cd-contaminated soil coupled with safe production of vegetables simultaneously.

Plants, animals, and fisheries waste-mediated bioremediation of contaminants of environmental and emerging concern (CEECs)-a circular bioresource utilization approach

The release of contaminants of environmental concern including heavy metals and metalloids, and contaminants of emerging concern including organic micropollutants from processing industries, pharmaceuticals, personal care, and anthropogenic sources, is a growing threat worldwide. Mitigating inorganic and organic contaminants, which can be coined as contaminants of environmental and emerging concern (CEECs), is a big challenge as traditional physicochemical processes are not economically viable for managing mixed contaminants of low concentrations. As a result, low-cost materials must be designed to provide high CEEC removal efficiency. One of the environmentally viable and energy-efficient approaches is biosorption, which involves using biomass or biopolymers isolated from plants or animals to decontaminate heavy metals in contaminated environments using inherent biological mechanisms. Among chemical constituents in plant biomass, cellulose, lignin, hemicellulose, proteins, polysaccharides, phenolic compounds, and animal biomass include polysaccharides and other compounds to bind heavy metals covalently and non-covalently. These functional groups include carboxyl, hydroxyl, carbonyl, amide, amine, and sulfhydryl. Cation-exchange capacities of these bioadsorbents can be improved by applying chemical modifications. The relevance of chemical constituents and bioactives in biosorbents derived from agricultural production such as food and fodder crops, bioenergy and cash crops, fruit and vegetable crops, medicinal and aromatic plants, plantation trees, aquatic and terrestrial weeds, and animal production such as dairy, goatery, poultry, duckery, and fisheries is highlighted in this comprehensive review for sequestering and bioremediation of CEECs, including as many as ten different heavy metals and metalloids co-contaminated with other organic micropollutants in circular bioresource utilization and one-health concepts.

Highly Efficient Cationic/Anionic Cellulose Membranes for Removal of Cr(VI) and Pb(II) Ions

To achieve high throughput, low-pressure drops, and high adsorption capacity of Cr(VI) and Pb(II) in industrial wastewater treatment, cellulose membranes containing cationic and anionic groups were fabricated, respectively. In this process, cost-effective cotton fabrics were oxidized using sodium periodate, followed by quaternary ammonium or sulfonation modifications. The chemical composition, surface morphology, and thermal and mechanical properties of the cellulose membranes were investigated by ATR-FTIR, solid-state NMR, SEM, TGA, and tensile experiments. Quaternary ammonium, aldehyde, and sulfonate groups were distributed on the cationic/anionic cellulose fibers as adsorption sites, which issue remarkable adsorption capability to the cellulose membranes. The highly toxic Cr(VI) and Pb(II) ions were used to challenge the adsorption capacity of the cationic and anionic cellulose membranes, respectively. The maximum adsorption capacities of Cr(VI) and Pb(II) ions were 61.7 and 63.7 mg/g, respectively, suggested by Langmuir isotherms, kinetics, and thermodynamics in the static experiments. The dynamic adsorption capability of cationic cellulose membranes against Cr(VI) ions was determined and compared with that of commercially available anionic-exchange membranes. Spiral wound filtration cartridges were fabricated by cationic and anionic cellulose membranes, respectively, and were used to adsorb Cr(VI) and Pb(II) from lab-made wastewater, respectively. The cationic cellulose cartridge can purify 4.4 L of wastewater containing 1.0 mg/L of Cr(VI) ions with a 100% removal ratio, while the pressure drop was retained at 246 Pa. Similarly, the anionic cellulose cartridge exhibited even more impressive adsorption capability; the removal ratio against Pb(II) was 99% when 8.6 L of 1.0 mg/L of Pb(II) ions containing wastewater was treated, and the pressure drop was retained at 234 Pa. A composite cartridge fabricated by the integration of cationic and anionic cellulose membranes was successfully employed to purify the wastewater containing Cr(VI) and Pb(II) simultaneously. The possible adsorption mechanism was proposed, and the recycling ability of the cellulose membranes was also discussed.

Application of chemometrics tools for removal of crystal violet and methylene blue in binary solution by eco-friendly magnetic adsorbent modified on Heracleum persicum waste

Synthetic dyes can be hazardous to the ecosystem, even at low concentrations in the effluent. In this research, the Heracleum persicum stems-Fe3O4 (MHPS) adsorbent performance for the removal of crystal violet (CV) and methylene blue (MB) from binary aqueous solutions was investigated in a batch method under the influence of different parameters. In addition, predictive models for the adsorption process were developed using machine learning techniques such as artificial neural networks and random forests. ANN and RF models achieved high R² values of 0.9501 and 0.9797 for CV, 0.9471, and 09,834 for MB, respectively, and obtained low MSE values of 0.07107 and 0.03405 for CV, 0.09933, and 0.02908 for MB. The proposed adsorbent is cheap and eco-friendly and, on the other hand, is easily collected by the magnetic field. The adsorbent was characterized by applying FESEM-EDX, FESEM, BET, and FTIR. Various isotherm and kinetics models for the simultaneous adsorption of CV and MB were investigated in aqueous solutions. The adsorption isotherm and kinetics studies explain that the extended Langmuir model and pseudo-second-order models are best suited for CV and MB in the binary solution. The exothermic adsorption was achieved in the temperature range of 5-45 °C.

Insights into the Applications of Natural Fibers to Metal Separation from Aqueous Solutions

There is a wide range of renewable materials with attractive prospects for the development of green technologies for the removal and recovery of metals from aqueous streams. A special category among them are natural fibers of biological origin, which combine remarkable biosorption properties with the adaptability of useful forms for cleanup and recycling purposes. To support the efficient exploitation of these advantages, this article reviews the current state of research on the potential and real applications of natural cellulosic and protein fibers as biosorbents for the sequestration of metals from aqueous solutions. The discussion on the scientific literature reports is made in sections that consider the classification and characterization of natural fibers and the analysis of performances of lignocellulosic biofibers and wool, silk, and human hair waste fibers to the metal uptake from diluted aqueous solutions. Finally, future research directions are recommended. Compared to other reviews, this work debates, systematizes, and correlates the available data on the metal biosorption on plant and protein biofibers, under non-competitive and competitive conditions, from synthetic, simulated, and real solutions, providing a deep insight into the biosorbents based on both types of eco-friendly fibers.

In vitro wheat protoplast cytotoxicity of polystyrene nanoplastics

Nanoplastics are an emerging environmental pollutant, having a potential risk to the terrestrial ecosystem. In the natural environment, almost all the micro-or nano-plastics will be aged by many factors and their characterizations of the surface will be modified. However, the toxicity and mechanism of the modified polystyrene nanoparticles (PS-NPs) to plant cells are not clear. In the study, the amino- and carboxyl-modified PS-NPs with different sizes (20 and 200 nm) were selected as the typical representatives to investigate their effects on protoplast cell viability, reactive oxygen species (ROS) production in the cell and the leakage of cell-inclusion and apoptosis. The results indicated that the 20 nm amino-modified PS-NPs (PS-20A) could significantly damage the structure of the cell, especially the cell membrane, chloroplast and mitochondrion. After being modified by amino group, smaller size nanoplastics had the potential to cause more severe damage. In addition, compared with carboxyl-modified PS-NPs, the amino-modified PS-NPs induced more ROS production and caused higher membrane permeability/lactate dehydrogenase (LDH) leakage. Apoptosis assay indicated that the proportion of viable cells in the PS-20A treatment decreased significantly, and the proportion of necrotic cells increased by four times. This study provides new insights into the toxicity and damage mechanism of PS-NPs to terrestrial vascular plants at the cellular level, and guides people to pay attention to the quality and safety of agricultural products caused by nanoplastics.

Effect of combined aging treatment on biochar adsorption and speciation distribution for Cd(II)

As a passivation material for heavy metals in-situ remediation, biochar (BC) has often been expected to maintain long-term adsorption performance for target pollutants. There is still lack of consensus about the impact of aging processes on biochar properties, particularly with respect to its long-term sorption performance. In this study, the changes to immobilization mechanisms as well as the speciation distribution of Cd(II) triggered by combined aging simulation (dry-wet, freeze-thaw cycle and oxidation treatment) on BC prepared under three levels of pyrolysis temperatures (300, 500 and 700 °C) were investigated. The results showed significant inhibition of aging on adsorption performance with the adsorptive capacity of BC300, BC500 and BC700 for Cd(II) decreased by 31.12 %, 50.63 % and 14.94 %, respectively. However, sequential extraction results indicated little influence of the aging process on the relative fractionation of Cd(II) speciation. The distribution of readily bioavailable, potentially bioavailable and non-bioavailable fractions of Cd(II) on BC showed only minimal changes post-aging. Overall, there was less Cd(II) sorption following aging, but the fractional availability (in relative terms) remained the same. Compared with 300 and 700 °C, the biochar prepared under 500 °C accounted the highest fraction of non-bioavailable Cd(II) (67.23 % of BC500, 59.17 % of Aged-500), and thus showed most promising for Cd(II) immobilization. This study has important practical significance for the long-term application of biochar in real environment.

Do tillage systems affect the cadmium threshold in farmland soil for environmental quality standard setting?

Tillage systems may change the cadmium (Cd) threshold of farmland soil. However, there have been few studies on this topic. Therefore, this study aimed to explore the influence of tillage systems on Cd threshold. The study conducted 2-year field experiments under different tillage systems (early rice-fallow, early rice-late rice and early rice-vegetable) at three typical Cd-polluted sites in China. The species sensitivity distribution (SSD) method was used to construct the SSD curves for the calculation of the Cd threshold by analyzing the experimental data. The sensitivity analysis results based on the SSD curves revealed that the sensitivities to Cd in rice varieties under the same tillage system were substantially different but almost the same under different tillage systems. These results can help select rice varieties with low Cd sensitivity for crop safety. Different tillage systems at the same site varied in their influence on Cd threshold values. Cd threshold values under early rice-late rice (e.g., 0.27, 0.28 mg/kg in Xiangtan City) and early rice-vegetable (e.g., 0.26, 0.31 mg/kg in Xiangtan City) tillage systems were roughly lower than that under the early rice-fallow tillage system (e.g., 0.33, 0.35 mg/kg in Xiangtan City). Notably, the influence of tillage systems resulted in Cd threshold values being generally lower than the Cd risk screening values of the current Chinese soil environmental quality standard. Analysis of the influence of different tillage systems on the Cd threshold is beneficial for the optimization of farmland soil environmental quality standards.

Insights into the heavy metal adsorption and immobilization mechanisms of CaFe-layered double hydroxide corn straw biochar: Synthesis and application in a combined heavy metal-contaminated environment

Biochar is an emerging eco-friendly and high-efficiency heavy metal (HM) adsorbent that exhibits satisfactory HM remediation effects in both water and soil environments. However, few studies have investigated the mechanisms and application of biochar in the remediation of combined HM-contaminated environments. Therefore, in the present study, a novel corn straw biochar-loaded calcium-iron layered double hydroxide composite (CaFe-LDH@CSB) was synthesized via the coprecipitation method and applied as a remediation adsorbent to remove HMs in both water and soil environments. The results indicated that the HM adsorption mechanism of CaFe-LDH@CSB in the aquatic phase involved a chemical endothermic adsorption process of functional group-complexed monolayers, dominated by precipitation, ion exchange, complexation and π bond interactions. The maximum adsorption capacity for Cd(II), Pb(II), Zn(II) and Cu(II) in the aqueous phase reached 24.58, 240.96, 57.57 and 39.35 mg g^-1, respectively. In addition, application of CaFe-LDH@CSB in the combined HM-contaminated soil treatment helped to increase the soil pH, which increased by 5.1-17.9% in low-contamination (LC) soil and by 7.0-13.9% in high-contamination (HC) soil. Moreover, application of CaFe-LDH@CSB effectively decreased the acid-soluble fraction of HMs and increased the HM residual fraction. The immobilization mechanism of CaFe-LDH@CSB in the soil was concluded to involve pore filling, functional group action and electrostatic interactions. Overall, this study provided a novel LDH biochar composite that can be effectively applied in the remediation of combined HM-contaminated water and soil environments.

A censorious review on the role of natural lignocellulosic fiber waste as a low-cost adsorbent for removal of diverse textile industrial pollutants

BACKGROUND

Textile industries produce fabricated colored products using toxic dyes and other harsh chemicals. It is the responsibility of the textile industries to treat and eliminate these hazardous pollutants. However, due to the growing population demand, the treatment of these hazardous effluents is ineffective and imposes the treatment cost over the end users. The release of partially treated effluents in the environment may cause a severe threat to the ecology and its biota. The critical objective is to treat textile effluents efficiently using agricultural natural fiber waste. Generation of agricultural lignocellulosic fibrous waste increases every year due to growing population demand. Its use in the modern world is limited due to synthetic products. An alternative has enumerated to avoid wastage of fibrous resources and its clean disposal.

OBJECTIVE

The main objective of this review paper discussed the feasibility of lignocellulosic fibers and other lignocellulosic materials as natural low-cost adsorbent.

METHODS

The literature study was performed using Web of Science and Scopus indexed journals. The main factors considered to increase the adsorption ability, including the types of lignocellulosic surface modification techniques were searched with utmost importance for quality results. Intending to summarize the literature survey and provide persuasive content, systematic review process was considered for this novel article.

RESULTS

Out of 230 valuable publications, 159 published articles were considered for the present study until March 2022. The articles surplus with factors affecting adsorption (pH, adsorption dosage, surface area, temperature, initial concentration, contact time, physical and chemical properties of pollutants) and surface modification techniques (physical, chemical, and biological) were considered for this manuscript.

CONCLUSION

Overall, the physical and chemical modification methods are widely used instead of biological methods due to various factors as discussed briefly. Furthermore, the finding of this article supports the fact that the fibrous by-product resources are wasted in various occasions due to the modern lifestyle. Even though there is evidential possibility to implement the low-cost adsorbents, the industries limit their application prospects due to existing technology and financial compromises.

Galdieria sulphuraria ACUF427 Freeze-Dried Biomass as Novel Biosorbent for Rare Earth Elements

Rare earth elements (REEs) are essential components of modern technologies and are often challenging to acquire from natural resources. The demand for REEs is so high that there is a clear need to develop efficient and environmentally-friendly recycling methods. In the present study, freeze-dried cells of the extremophile Galdieria sulphuraria were employed to recover yttrium, cerium, europium, and terbium from quaternary-metal aqueous solutions. The biosorption capacity of G. sulphuraria freeze-dried algal biomass was tested at different pHs, contact times, and biosorbent dosages. All rare earths were biosorbed in a more efficient way by the lowest dose of biosorbent, at pH 4.5, within 30 min; the highest removal rate of cerium was recorded at acidic pH (2.5) and after a longer contact time, i.e., 360 min. This study confirms the potential of freeze-dried cells of G. sulphuraria as innovative ecological biosorbents in technological applications for sustainable recycling of metals from e-waste and wastewater.

Chitosan-Modified Biochars to Advance Research on Heavy Metal Ion Removal: Roles, Mechanism and Perspectives

The chitosan-modified biochars BC-CS 1-1, BC-CS 2-1 and BC-CS 4-1 were subjected to the synthetic application of biochar from agriculture waste and chitosan for the adsorption of Cu(II), Cd(II), Zn(II), Co(II) and Pb(II) ions from aqueous media. The results displayed a heterogeneous, well-developed surface. Additionally, the surface functional groups carboxyl, hydroxyl and phenol, determining the sorption mechanism and confirming the thermal stability of the materials, were present. The sorption evaluation was carried out as a function of the sorbent dose, pH, phase contact time, initial concentration of the solution and temperature. The maximum value of q_t for Pb(II)-BC-CS 4-1, 32.23 mg/g (C₀ 200 mg/L, mass 0.1 g, pH 5, 360 min), was identified. Nitric acid was applied for the sorbent regeneration with a yield of 99.13% for Pb(II)-BC-CS 2-1. The produced sorbents can be used for the decontamination of water by means of the cost-effective and high-performance method.

Removal and Mechanism of Cadmium, Lead and Copper in Water by Functional Modification of Silkworm Excrement Biochar

A new type of biochar, called GBC, was prepared from silkworm excrement, and then modified by chitosan combined with pyromellitic dianhydride. The removal of mono-metal and polymetals (Pb, Cd and Cu) from an aqueous solution by GBC was investigated in this research. Compared to unmodified biochar, the removal rate of Pb and Cd by GBC was about 12% higher, while that of Cu was about 94.6% higher. It also shows the types of functional groups in biochar have a great impact on their adsorption. The removal of Pb is mainly involved in the N-C=O functional group, the removal of Cd is mainly involved in N-containing functional group and C=C bond, and that of Cu is mainly involved in N-containing functional group, carboxyl group, hydroxyl group, and a carbonyl group. Five adsorption–desorption cycles of GBC were carried out, and it was found that the adsorption capacities of GBC for Pb, Cd and Cu decreased by 7.28%, 10.78% and 6.07%, respectively, indicating that GBC had a good renewable performance. The adsorption capacity of GBC for Cu in different water samples is between 89.62 and 93.47 mg·g⁻¹, indicating that GBC has great application potential for the removal of Cu in wastewater.

Application of random forest for modeling batch and continuous fixed-bed removal of crystal violet from aqueous solutions using Gypsophila aretioides stem-based biosorbent

In this work, the Gypsophila aretioides (GYP-A) stem is used as a biosorbent to remove crystal violet (CV) by the static and dynamic systems from aqueous solutions; the biosorbent is interesting in green chemistry and, on the other hand, cheaper than activated carbon and does not have the limitation of industrialization. The effects of different operating parameters such as pH(3-9), biosorbent dosage(0.4-1.8 mg/L), and initial concentration of CV(100-250 mg/L) and time for the batch method and the bed height, inlet CV concentration(75-250 mg/L), and flow rate(3-8) on the breakthrough curves for the continuous method is investigated. The result of CV adsorption onto GYP-A using the batch method indicates that the model fits Freundlich > Temkin > Langmuir > R-D, and R² equal 0.9953, 0.9847, 0.9161, 0.7909 were obtained for isotherm model, respectively. A pseudo-second-order model (R² = 0.9995-0.9997) is recommended to describe the adsorption kinetics. The Thomas and Yoon-Nelson models were analyzed to study the adsorption kinetics. The random forest model shows an excellent ability to predict the parameters involved in the CV adsorption process with appropriate accuracy and useable for large data, robust against noise; it can be very effective in selecting important variables.

A high-performance polymer hydrogel derived from konjac flying powder for removal of heavy metals

Agricultural byproducts have excellent potential for pollutant remediation due to the low-cost and environmental sustainability.

Progress in the Production of Biogas from Maize Silage after Acid-Heat Pretreatment

One of the most effective technologies involving the use of lignocellulosic biomass is the production of biofuels, including methane-rich biogas. In order to increase the amount of gas produced, it is necessary to optimize the fermentation process, for example, by substrate pretreatment. The present study aimed to analyze the coupled effects of microwave radiation and the following acids: phosphoric(V) acid (H3PO4), hydrochloric acid (HCl), and sulfuric(VI) acid (H2SO4), on the destruction of a lignocellulosic complex of maize silage biomass and its susceptibility to anaerobic degradation in the methane fermentation process. The study compared the effects of plant biomass (maize silage) disintegration using microwave and conventional heating; the criterion differentiating experimental variants was the dose of acid used, i.e., 10% H3PO4, 10% HCl, and 10% H2SO4 in doses of 0.02, 0.05, 0.10, 0.20, and 0.40 g/gTS. Microwave heating caused a higher biogas production in the case of all acids tested (HCl, H2SO4, H3PO4). The highest biogas volume, exceeding 1800 L/kgVS, was produced in the variant with HCl used at a dose of 0.4 g/gTS.

Adsorption of Toxic Zinc by Functionalized Lignocellulose Derived from Waste Biomass: Kinetics, Isotherms and Thermodynamics

Heavy metals pollution receives worldwide attention due to great toxicity, significant bio-accumulation and non-biodegradability. Adsorption is a promising technique for removing heavy metals from wastewater. Adsorption of zinc (Zn(II)) from aqueous solution was investigated by functionalized lignocellulose derived from fallen leaves. Alkalized lignocellulose (AC), xanthated lignocellulose (XC) and carboxylated lignocellulose (CC) were characterized by Fourier transform infrared spectrum (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The effect of sorbent dosage, solution pH, sorption time and initial Zn(II) concentration on Zn(II) sorption was investigated by single-factor experiment. Sorption kinetics, isotherms and thermodynamics were examined to reveal sorption mechanism. The sorption capacity and removal rate remarkably depend on experimental variables. Zn(II) sorption onto AC, XC and CC is well described by the pseudo second order kinetics and Langmuir isotherm. The sorption process is fast, reaching sorption equilibrium at 30 min. The maximum sorption capacity of Zn(II) onto CC is 46.49 mg/g, higher than that onto AC, XC and other reported sorbents. Thermodynamic parameters indicate that Zn(II) sorption is a spontaneous process. Sorption mechanism is majorly attributed to surface complexation. This work shows the feasibility of removing toxic Zn(II) from aqueous solution by locally available biomass, providing a sustainable approach for wastewater treatment.

Mechanism and industrial application feasibility analysis on microwave-assisted rapid synthesis of amino-carboxyl functionalized cellulose for enhanced heavy metal removal

The study presented the successful microwave-assisted (MW-assisted) preparation of a novel adsorbent derived from rice straw (RS_MW-AC) and explored its adsorption performance toward heavy metal ions from water. The RS_MW-AC was rapidly synthesized through pretreatment and one step grafting via the MW-assisted approach. The quantitative predictive correlations between target performance of RS_MW-AC and process parameters were obtained through the response surface methodology (RSM). Meanwhile, the optimal preparation process conditions were determined: NaOH solution concentration, 20%; MW irradiation temperature for pretreatment, 100 and 150 °C; MW irradiation time for pretreatment and grafting, 10 and 60 min; EDTAD-RS mass ratio, 3. The RS_MW-AC showed a good adsorption of different heavy metal ions from water (152.39, 55.46, 52.91, 35.60 and 20.11 mg g^-1 for Pb(Ⅱ), Mn(Ⅱ), Cd(Ⅱ), Cu(Ⅱ) and Ni(Ⅱ), respectively). The adsorption behaviors followed the Langmuir model and pseudo second-order kinetics model with a highly significant correlation. Also of note was that amino and carboxyl groups were successfully introduced on the rice straw based on characterization results. Furthermore, preparation mechanism was explored to reveal reasons why microwave irradiation could accelerate the preparation of the adsorbent; its adsorption process was dominated by electrostatic attraction and chelation. Finally, the study made the industrial application feasibility analysis of MW-assisted approach used for pretreatment and graft reaction of agro-waste biomass.

Boosting adsorption of heavy metal ions in wastewater through solar-driven interfacial evaporation of chemically-treated carbonized wood

Once the adsorbent is selected, almost introducing larger specific surface area and more surface functional groups becomes the only way to improve its adsorption performance. However, this approach is generally limited in practical application for intricate and costly engineering steps. Herein, we provided a novel avenue for boosting adsorption activities towards specific metal ions in wastewater. Solar-driven interfacial water evaporation produces the localized temperature field and concentration gradient of metal ions inside small pores, endowing with a new sorption mechanism. By using chemically-treated carbonized wood as all-in-one solar absorption and metal ion adsorption system, we achieved higher water evaporation rate and heavy metal ion removal efficiency than carbonization-only wood reported previously. In particular, this system exhibited a strong dependence of specific metal ion adsorption capacity on solar intensity. Pb²⁺ adsorption capacity was enhanced by over 225% with the solar intensity increased to 3.0 kW·m^-2. This could originate from the formed temperature field localized specially on the surface of adsorbents that not only induces Pb²⁺ concentration gradient near to solid-liquid interface but also activate inactive adsorption sites. Besides, the chemical-treated & carbonized wood showed excellent cyclic stability and can be directly utilized for wastewater treatment, recovery and reuse.

Microwave-assisted synthesis of β-cyclodextrin functionalized celluloses for enhanced removal of Pb(II) from water: Adsorptive performance and mechanism exploration

Herein, β-cyclodextrin (β-CD) was efficiently grafted onto rice husk-based celluloses using different cross-linking agents of epichlorohydrin (EPI) and glutaraldehyde (GA). By feat of microwave irradiation, the functionalization procedure was completed in 17 min, and the synthesized RHEPIMWβ-CD and RHGAMWβ-CD exhibited fast adsorption equilibrium for Pb(II) within 20 min, excellent monolayer adsorption capacities of 216.06 and 279.08 mg g^-1 across an extensive pH scope of 3.0-6.0, unaffected affinity to Pb(II) during the existence of co-existing ions, superior reusability with over 81% and 87% of Pb(II) uptake sustained for four adsorption-desorption cycles. Thermodynamic parameters implied that the uptake process of Pb(II) occurred spontaneously (-ΔG⁰) with an endothermic characteristic (+ΔH⁰). Furthermore, electrostatic attraction and complexation were demonstrated to enhance the Pb(II) uptake onto the RHEPIMWβ-CD and RHGAMWβ-CD. In fix-bed columns, these two adsorbents also efficiently eliminated Pb(II) under various flow rates with experimental breakthrough curves well simulated by Thomas and Yoon-Nelson models. Significantly, the RHEPIMWβ-CD and RHGAMWβ-CD could effectively purify acid battery effluent containing Pb(II) for meeting regulatory requirement. Overall, the fast fabrication, excellent adsorption and recycling performance facilitate the development of tailored adsorbents for Pb(II) elimination in wastewater.

Microwave-assisted one pot synthesis of β-cyclodextrin modified biochar for concurrent removal of Pb(II) and bisphenol a in water

Herein, β-cyclodextrin (β-CD) functionalized rice husk-derived biochar (BC) was conveniently and fast synthesized via microwave (MW)-assisted one pot process, and employed for simultaneous elimination of bisphenol A (BPA) and plumbum (Pb). Profiting by microwave irradiation, the surface modification was implemented in 15 min and the prepared BC_MW-β-CD presented an excellent adsorption performance with a heterogeneous adsorption capacity of 209.20 mg/g for BPA and a theoretical monolayer uptake of 240.13 mg/g for Pb(II) in the mono-component system. Furthermore, the BC_MW-β-CD could simultaneously achieve efficient cleanup of BPA and Pb(II) through avoiding the competitive behaviors between them, which were due to the different adsorption mechanisms for Pb(II) (i.e. electrostatic attraction and complexation) and BPA (i.e. host-guest supramolecular and π-π interactions). Moreover, the adsorbed BPA and Pb(II) could be sequentially desorbed with mild decrease in the adsorption performance of BC_MW-β-CD even after five cycles in the Pb(II)-BPA multi-component system.

Multi-component adsorption of Pb(II), Cd(II) and Ni(II) onto microwave-functionalized cellulose: Kinetics, isotherms, thermodynamics, mechanisms and application for electroplating wastewater purification

Herein, microwave-functionalized cellulose derived from rice husk was cost-effectively prepared and employed for Pb(II), Cd(II) and Ni(II) elimination in mono- and multi-component systems. Benefiting from microwave irradiation, the functionalized process was achieved in 6.5 min and the resultant RH_MW-X possessed remarkably high adsorption capacities of 295.20 mg/g for Pb(II), 151.51 mg/g for Cd(II) and 72.80 mg/g for Ni(II) within the equilibrium time of 30 min. Noticeably, the metal ions adsorption rate and capacity in binary and ternary systems were lower than that of unary systems. The coexistence of Cd(II) and Ni(II) significantly slowed down the Pb(II) adsorption in binary and ternary systems, while Pb(II) exhibited the most obvious influence on the metal ions uptake in the multi-component systems. FT-IR and XPS results revealed that both ion exchange and chelation were functioned in the metal ions uptake, while physical interaction was also involved in the adsorption process. Moreover, the RH_MW-X possessed favorable recyclability with slight adsorption efficiency decline during five cycles in different systems. Particularly, the RH_MW-X could effectively purify actual industrial wastewater containing Pb(II), Cd(II) and Ni(II) for meeting regulatory requirements. This work facilitates the omnidirectional improvement of adsorbents for the de-pollution of practical heavy metals wastewater.

Enhanced and Selective Adsorption of Zn(II), Pb(II), Cd(II), and Hg(II) Ions by a Dumbbell- and Flower-Shaped Potato Starch Phosphate Polymer: A Combined Experimental and DFT Calculation Study

Microwave-ultrasound-assisted facile synthesis of a dumbbell- and flower-shaped potato starch phosphate (PSP) polymer, hereafter PSP, was carried out by cross-linking the hydroxyl groups of native potato starch (NPS) using phosphoryl chloride as a cross-linking agent. Structural and morphological analysis manifested the successful formation of the dumbbell- and flower-shaped PSP biosorbent with enhanced specific surface area and thermal stability. Viscoelastic behavior of NPS and PSP suggested increased rigidity in PSP, which helped the material to store more deformation energy in an elastic manner. The synthesized PSP biosorbent material was successfully tested for efficient and quick uptake of Zn(II), Pb(II), Cd(II), and Hg(II) ions from aqueous medium under competitive and noncompetitive batch conditions with q m values of 130.54, 106.25, 91.84, and 51.38 mg g-1, respectively. The adsorption selectivity was in consonance with Pearson's hard and soft acids and bases (HSAB) theory in addition to their order of hydrated radius. Adsorption of Zn(II), Pb(II), Cd(II), and Hg(II) followed a second-order kinetics and the adsorption data fitted well with the Langmuir isotherm model. Quantum computations using density functional theory (DFT) further supported the experimental adsorption selectivity, Zn(II) > Pb(II) > Cd(II) > Hg(II), in terms of metal-oxygen binding energy measurements. What was more intriguing about PSP was its reusability over multiple adsorption cycles by treating the metal(II)-complexed PSP with 0.1 M HCl without any appreciable loss of its adsorption capacity.

Preparation of thermoresponsive alginate/starch ether composite hydrogel and its application to the removal of Cu(II) from aqueous solution

A novel polysaccharide-based thermoresponsive hydrogel containing sodium alginate (SA) and 2-hydroxy-3-isopropoxypropyl starch (HIPS) was developed for removing Cu(II) from aqueous solution. HIPS/SA hydrogel showed network and porous structure, as well as the abundant carboxy groups inside the structure, endowed it with sufficient binding sites for adsorption of Cu(II). The reversible thermoresponsive swelling-shrinking behavior of HIPS/SA hydrogel was discussed. The effects of pH and initial Cu(II) concentration on adsorption capacity were investigated. The adsorption isotherms and kinetics of HIPS/SA hydrogel demonstrated that the adsorption of Cu(II) was subjected to Langmuir and pseudo-second-order models respectively, and the maximum adsorption capacity was 25.81 mg/g. Additionally, HIPS/SA hydrogel could be successfully desorbed by only small amounts of dilute hydrochloric acid within a short time for its thermoresponsive property, it also exhibited the feasibility of regeneration, because the adsorption capacity for Cu(II) was still higher than 15.23 ± 0.27 mg/g even after five cycles.

A combined system of microwave-functionalized rice husk and poly-aluminium chloride for trace cadmium-contaminated source water purification: Exploration of removal efficiency and mechanism

Cadmium is highly poisonous to mammals and related water pollution incidents are increasing world-widely. Here, the clean-up of trace Cd(II) by a combined process of microwave-functionalized rice husk (RH_MW-M) and poly aluminium chloride (PAC) was investigated for the first time, with the exploration of removal mechanism and efficacy. Microwave irradiation was found to be a new approach to achieve the functionalized procedure, which could decrease the processing time from 2.5 h to 390 s with the Cd(II) uptake of the outcome product soaring from 137.16 mg/g to 191.32 mg/g. The ultra-rapidly prepared RH_MW-M exhibited a fast adsorption equilibrium within 30 min over a wide pH range of 5.0-8.0, and the FT-IR and XPS studies confirmed that both ion exchange and chelation were functioned in the Cd(II) uptake process. Controlled by the turbidity threshold of drinking water treatment plant, the feasible dosage of RH_MW-M in the absence and presence of 30 mg/L PAC increased from 30 to 760 mg/L, which could effectively deal with the trace Cd(II) at the concentration from 33 μg/L up to 0.933 mg/L, exhibiting much better performance than traditional alkali precipitation. Predictably, this simple and scalable RH_MW-M/PAC system could afford a promising end-of-pipe solution for heavy-metal contamination.

Facile synthesis of Fe2O3 nanoparticles from Egyptian insecticide cans for efficient photocatalytic degradation of methylene blue and crystal violet dyes

In this study, Fe₂O₃ (hematite) nanoparticles with different crystallite sizes (40-59 nm) were synthesized from Egyptian insecticide cans using the combustion method. The organic fuels were urea, glycine, L-alanine, and L-valine. Fe₂O₃ nanoparticles were characterized utilizing different devices such as BET, PL, FT-IR, XRD, HR-TEM, FE-SEM, UV-Vis, and DTG. Crystal violet (CV) and methylene blue (MB) dyes were efficiently removed from aqueous solution by photocatalytic degradation under UV irradiation in the presence of Fe₂O₃ and H₂O₂. The % degradation of 50 mL crystal violet or methylene blue dye (20 mg/L) using 0.1 g Fe₂O₃ in the presence of H₂O₂ was 100% after 30 or 40 min, respectively. Also, the degradation processes are fitted well with the first order model. Besides, the photocatalytic activity of Fe₂O₃ unaltered even after it was reused three times. Hence, the synthesized Fe₂O₃ nanoparticles can be considered a promising and efficient photocatalyst for the degradation of crystal violet and methylene blue dyes.

Preparation of cotton-based fibrous adsorbents for the removal of heavy metal ions

Cotton fiber functionalized with tetraethylenepentamine and chitosan (CTPC) was prepared and used as absorbents for the removal of Cu(II), Pb(II) and Cr(III) ions from aqueous solution. The functionalized materials (CTPC) were characterized by SEM/EDX, FTIR, BET and XRD to confirm the characterization and structural changes of fibers before and after the modifying process. The adsorption performance of CTPC was investigated with different pH, contact time and initial concentration of three kinds of metal ions. Results showed that the maximum adsorption capacity was 81.97 mg g^-1 for Cu(II), 123.46 mg g^-1 for Pb(II) and 72.99 mg g^-1 for Cr(III) based on the Langmuir isotherm model at optimal pH (5.0). Adsorption kinetics of CTPC fibers for Cu(II), Pb(II), and Cr(III) ions followed the pseudo-second-order model. The adsorption-desorption experiments demonstrated that CTPC showed better stability, and CTPC would be an effective and practical material for the treatment and recycling of heavy metal ions in the wastewater.

A critical review on arsenic removal from water using iron-based adsorbents

Intensive research efforts have been pursued to remove arsenic (As) contamination from water with an intention to provide potable water to millions of people living in different countries. Recent studies have revealed that iron-based adsorbents, which are non-toxic, low cost, and easily accessible in large quantities, offer promising results for arsenic removal from water. This review is focused on the removal of arsenic from water using iron-based materials such as iron-based nanoparticles, iron-based layered double hydroxides (LDHs), zero-valent iron (ZVI), iron-doped activated carbon, iron-doped polymer/biomass materials, iron-doped inorganic minerals, and iron-containing combined metal oxides. This review also discusses readily available low-cost adsorbents such as natural cellulose materials, bio-wastes, and soils enriched with iron. Details on mathematical models dealing with adsorption, including thermodynamics, kinetics, and mass transfer process, are also discussed. For elucidating the adsorption mechanisms of specific adsorption of arsenic on the iron-based adsorbent, X-ray photoelectron spectroscopy (XPS) and X-ray absorption spectroscopy (XAS) are frequently used. Overall, iron-based adsorbents offer significant potential towards developing adsorbents for arsenic removal from water.

Utilizations of agricultural waste as adsorbent for the removal of contaminants: A review

In recent years, various industrial activities have caused serious pollution to the environment. Due to the low operating costs and high flexibility, adsorption is considered as one of the most effective technologies for pollutant management. Agricultural waste has loose and porous structures, and contains functional groups such as the carboxyl group and hydroxyl group, so it can be invoked as biological adsorption material. Agricultural waste gets the advantages of a wide range of sources, low cost, and renewable. It has a good prospect for the comprehensive utilization of resources when used for environmental pollution control. This article summarized the current research status of agricultural waste in adsorbing pollutants, which pointed out the influencing factors of adsorption, expounded the adsorption mechanism of biological adsorption and introduced the related parameters of adsorption, proposed the application of adsorbents in engineering including adsorption in liquid and gas phases, at the same time it gave the future development prospect of agricultural waste as adsorbent.

Efficient removal of Cd2+ and Pb2+ from aqueous solution with amino- and thiol-functionalized activated carbon: Isotherm and kinetics modeling

In order to address the increasingly severe pollution issue caused by heavy metals, activated carbon-based absorbents have gained considerable attention. Herein, two novel adsorbents, amino-functionalized activated carbon (N-AC) and thiol-functionalized activated carbon (S-AC), were successfully synthesized by stepwise modification with tetraethylenepentamine (TEPA), cyanuric chloride (CC) and sodium sulfide. The pristine and synthesized materials were characterized by BET analysis, SEM, FTIR spectroscopy, elemental analysis and zeta-potential analyzer. Meanwhile, their adsorption properties for Cd²⁺ and Pb²⁺ and the effects of various variables on the adsorption processes were systematically investigated. The findings confirmed that amino-groups and thiol-groups endowed the AC with a strong affinity for metal ions and that the pH of solution affected the uptake efficiencies of the adsorbents by influencing their surface charges. Furthermore, six isotherm models (Langmuir, Freundlich, Temkin, Dubinin-Radushkevich, Sips and Redlich-Peterson) and four kinetic models (pseudo-first-order, pseudo-second-order, Intra-particle diffusion and Elovich) were applied to interpret the adsorption process at three different temperatures (288 K, 298 K and 308 K). The results indicated that temperature played an important role and that the rate-limiting step was chemosorption. A better fit for all adsorption systems was obtained with Langmuir model, with the maximum adsorption capacities at 298 K of 79.20 mg Cd²⁺/g and 142.03 mg Pb²⁺/g for N-AC, 130.05 mg Cd²⁺/g and 232.02 mg Pb²⁺/g for S-AC, respectively. Subsequently, the thermodynamic parameters revealed the nature of the adsorption was endothermic and spontaneous under the experimental condition. The possible adsorption procedures and the underlying mechanisms comprising physical and chemical interactions were proposed. Moreover, the as-synthesized adsorbents exhibited excellent regeneration performance after five adsorption/desorption cycles. The overall results demonstrated that both N-AC and S-AC could be the promising efficient candidates for removing Cd²⁺ and Pb²⁺ from contaminated water.

Comparative efficacy of locally isolated fungal strains for Pb(II) removal and recovery from water

The present investigation aimed to study and compare the efficiency of non-viable fungal isolates to remove divalent lead (Pb(II)) from aqueous streams. The selected fungal isolates showed identity with Aspergillus caespitosus, Aureobasidium sp. RBSS-303 and Aspergillus flavus HF5 as confirmed using gene sequencing of ITS regions of the ribosomal DNA (rDNA). The obtained equilibrium data for Pb(II) biosorption of A. caespitosus fitted better to Langmuir isotherm with maximum sorption capacity of 351.0 mg/g and A. sp. RBSS-303 and A. flavus HF5 showed good fit to Freundlich isotherm with maximum sorption capacity of 271.5 and 346.3 mg/g respectively. The values of thermodynamic factors ascertained the nature of adsorption process is endothermic with A. caespitosus and A. flavus HF5 but exothermic with A. sp. RBSS-303. The experimental data for Pb(II) biosorption fits very well to pseudo second order kinetic model. With HCl the maximum 85.5, 75.3, 73.7% recovery of Pb(II) was obtained from A. caespitosus, A. sp. RBSS-303 and A. flavus HF5, respectively. The observed percentage loss in sorption capacity of Pb(II) was 3.9% by A. flavus HF5, 12.2% by A. caespitosus and 26.6% by A. sp. RBSS-303 after five cyclic studies of sorption and desorption. Results from the study confirmed the efficiency order of A. caespitosus > A. flavus HF5 > A. sp. RBSS-303 to remove and recover Pb(II) from aqueous solution. Finally, the fungal biosorbents can be used as soil conditioning agent after compositing into valuables fungal protein.

Adsorption and one-step degradation-regeneration of 4-amino-5-hydroxynaphthalene-2,7-disulfonic acid using biochar-based BiFeO3 nanocomposites

A microwave (MW)-assisted-H₂O₂ technique used to revise 4-amino-5-hydroxynaphthalene-2,7-disulfonic acid (H-acid)-saturated biochars (BCs) was investigated in detail. This method could simultaneously degrade the H-acid adsorbed in the BCs-based BiFeO₃ (BFO) nanocomposites (BFO/BCs), in which BFO was used as dopant intercalated into BC, and activate the used BCs. Because H-acid could be decomposed by OH, which was generated in a coexistent system, including MW irradiation, H₂O₂, and BCs. It's worth noticing the adsorption capacity was (236.8mgg^-1) 1.1-fold higher than that of unused BFO/BC (211.7mgg^-1). It indicated that the surplus OH exhibited a cooperative effect with MW irradiation to restore H-acid-saturated BCs via the cleavage of CC bond, thereby forming carboxylic groups and the pyrolysis effect. Findings indicated that the one-step degradation-regeneration method could effectively promote the adsorption capacity of H-acid-saturated BCs in a few minutes and could thus be considered a potential technology in water treatment.