Hydrodynamic shear force shaped the microbial community and function in the aerobic granular sequencing batch reactors for low carbon to nitrogen (C/N) municipal wastewater treatment

Study on the mechanisms of efficient phosphorus recovery by a pilot-scale biofilm sequencing batch reactor under low carbon demand

To study the mechanism of a novel pilot-scale biofilm sequencing batch reactor (PS-BSBR) for efficient phosphorus recovery under low carbon demand. The phosphate uptake/release performance and carbon source utilization efficiency of PS-BSBR and a typical enhanced biological phosphate removal (EBPR) -A2O process were compared, and the detection methods of different phosphorus forms were improved. The results showed that phosphate uptake/release content of PS-BSBR were 3.07 times and 4.47 times of that of A2O process under high carbon source utilization efficiency, respectively. The PS-BSBR mainly used inorganic phosphorus (IP) in the form of non-apatite inorganic phosphorus (NAIP) in EPS (85-90%), which was dependent on the adsorption of biologically induced extracellular polymers (EPS). The A2O process was mainly based on the IP in the form of NAIP (60-70%) in the cell for phosphate uptake and release, that was, relying on the biological phosphorus metabolism in the cell of polyphosphate-accumulating organisms (PAOs). Macroomics sequencing revealed that PS-BSBR had a variety of PAOs and a high-abundance glycogen-accumulating organisms (GAOs). By up-regulating the expression of key genes related to cellular phosphorus metabolism and EPS secretion, PS-BSBR promoted the phosphorus metabolism of PAOs cells and the biologically induced phosphate adsorption and desorption, which were dominated by the synthesis and decomposition of EPS. Therefore, the phosphorus absorption and release performance of PS-BSBR process was significantly better than that of A2O process. This study could provide theoretical support and regulatory guidance for the application of PS-BSBR process in sewage phosphorus recovery under the consumption of low carbon sources.

Flow condition mitigates the inhibition of high concentration Cu2+ on the sulfate reduction performance of microbial electrolysis cell

Microbial electrolysis cells (MECs) are promising for treating acidic mine drainage (AMD) containing high concentrations of sulfates and heavy metals. However, the performance of MEC cathodic biofilms is influenced not only by high heavy metals concentrations but also by hydrodynamic mixing conditions. Yet, there is a lack of precise assessment on the impact of hydrodynamic mixing conditions on MEC treating sulfate-laden wastewater under high heavy metal stress, and the defense mechanisms of MECs remain unclear. This study investigated the effects of different hydrodynamic conditions (EG, flow condition; CG, stationary condition) on the performance of MECs treating sulfate wastewater under high heavy metal stress, delving into microbial activity, community composition, electrochemical performance, and microbial defense capabilities against heavy metals. The results indicated that under heavy metal stress, microbial cells underwent severe deformation and death, with the assimilatory sulfate reduction pathway severely impaired, leading to a decline in MEC performance, and the reduction rate of CG group was finally reduced to 14.47%. In contrast, under flow conditions, the EG group exhibited increased extracellular polymeric substances (EPS) composition, enhanced biofilm community diversity, and elevated levels of copper resistance genes, significantly mitigating the inhibitory effects of Cu2+ on microorganisms, ultimately maintaining a performance of 47.18%. Ultimately, Cu2+ in the system was removed through bioprecipitation and biosorption, forming CuS and Cu(OH)2. This work provides critical insights for scaling up MEC technology to address co-contamination challenges in acid mine drainage remediation, particularly for environments with hydrodynamic mixing conditions and elevated heavy metal concentrations.

Salinity stress and recovery of the algal-bacterial granular sludge (ABGS) system under the influence of different N-acyl-homoserine lactones (AHLs)

The algal-bacterial granular sludge (ABGS) system was established to explore the effect of 1% salinity condition, determine the recovery process following salinity disturbance, and probe the impacts of two N-acyl-homoserine lactones (AHLs) on the system. Exposure to 1% salinity led to the reduction of filaments and an increase in TB-EPS contents within the ABGS system. The phosphorus removal performance of the ABGS system severely decreased at 1% salinity and did not restore fully during the subsequent recovery stage, demonstrating that salinity stress induced long-term inhibition. Oligotrophic bacteria were found to be enriched at 1% salinity, indicating the self-adaptation of the ABGS system against salinity stress. The addition of AHLs helped mitigate the inhibitory effect of salinity stress. Specifically, C6-HSL slowed down the decline in microbial diversity, while 3-oxo-C12-HSL weakened the inhibition on microalgae growth. This study provided novel insights into the effects of salinity stress and AHLs on ABGS systems.

Achieving stable partial nitrification by exploiting lag phase of NOB recovery for selective washout

Stable inhibition of nitrite-oxidizing bacteria (NOB) is a significant challenge in achieving partial nitrification (PN) and partial nitrification-anaerobic ammonia oxidation (PNA). Growing evidence suggested that NOB can develop resistance to suppression over time, leading to the re-enrichment of NOB within reactors. To address these issues, this study aimed to achieve stable PN by regulating SRT to selectively washout NOB during the lag phase of activity recovery following FA/FNA exposure. The effects of this new strategy on nitrifying bacteria, sludge characteristics, and microbial interspecies relationships were investigated over a 150-day trial. Under the new strategy operation, the effluent ammonia, nitrite, and nitrate concentrations were 4.72 mg/L, 51.81 mg/L, and 3.30 mg/L, respectively, at a dissolved oxygen (DO) concentration of 0.18 mg/L, with a nitrite accumulation rate (NAR) remaining above 95%. This was attributed to the increasing relative abundance of ammonia-oxidizing bacteria (AOB) (Nitrosomonas) up to 25.86% and the decreasing relative abundance of NOB (Nitrospira, Nitrobacter and Candidatus Nitrotoga) to below the detection limit (1%) during the stabilization period. Analysis of the PN sludge characteristics revealed a tendency for sludge to form loosely structured aggregates, facilitating the potential rapid start-up of the PNA biofilm system or granular sludge. These findings suggest that the new strategy is a straightforward and effective method for achieving PN.

Unraveling the resistance mechanism of anammox granular sludge to iron nanoparticles

Iron nanoparticles (FeNPs) generated from industrial activities could end up into the sewer system, and potentially affect wastewater treatment processes. The impact of FeNPs on anammox process is getting increasing attention. However, the resistance mechanism of anammox granular sludge (AnGS) to FeNPs has not been fully elucidated. The current study investigated the metabolic and morphological response of AnGS to acute and chronic FeNPs exposure. Results showed that nitrogen removal efficiencies were elevated at 1-4 mM FeNPs concentrations compared to 0-0.5 mM FeNPs. Extracellular protein and tyrosine-like and tryptophan-like fluorophore secretions of AnGS were stimulated by FeNPs, which largely contributed to the adsorption of FeNPs on AnGS surface. FeNPs exposure triggered higher necrotic fraction of AnGS compared with no FeNPs condition. Highly absorbed particles appeared inside the bacterial cells of AnGS, soft X-ray imaging illustrated that anammox bacteria maintained intact cellular and anammoxosome structures whereas non-anammox bacterial structures were damaged under FeNPs exposure. Anammox bacterial abundance increased from 4.84% to 20.64%, when FeNPs concentrations increased from 0 mM to 4 mM, and anammoxosome membrane ensured anammox bacterial metabolism under FeNPs exposure. This study extended fundamental understanding of AnGS resistance mechanisms to FeNPs.

Exogenous signaling molecules N-acyl-homoserine lactones promotes the reconstruction of sludge particles after impact with highly concentrated urea-formaldehyde resin microplastics

In this study, exogenous N-acyl-homoserine lactones (AHLs) was added to resist the stress by high concentration (0.5 g/L) of urea formaldehyde resin microplastics (UF-MPs) on anaerobic granular sludge (AnGS), aiming to provide a viable strategy for AnGS to withstand elevated levels of UF-MPs toxicity elucidate the intricate regulatory mechanism of AHL-mediated AnGS-QS regulation. The results showed that the three different signaling molecules (C4-HSL, C6-HSL, and C8-HSL) improved the performance of AnGS under high concentration (0.5 g/L) urea-formaldehyde resin stress, and increased sludge COD removal (4.48%, 4.76%, and 3.35%, respectively) and methanogenic activity (8.38%, 1.92%, and 18.76%, respectively). The addition of C4-HSL has the best effect on sludge particle size and strength, which is attributed to the fact that C4-HSL can significantly increase the content of polysaccharides and proteins in tightly bound extracellular polymeric substances (TB-EPS) (27.1% and 27.1%, respectively). C8-HSL most obviously promotes energy metabolism and EPS biosynthesis gene expression. Metagenomic analysis showed that trace AHLs could promote the abundance of enzymes and functional genes related to the main pathway of methane metabolism, increase the relative abundance of Methanothrix of acetophilic methanogens from 27.79% in the control group to 27.85% (C4-HSL), 28.90% (64-HSL), and 30.03% (C8-HSL), thereby improving community stability.

Enhanced nitrogen removal from secondary effluent of municipal wastewater using denitrification filter: Feasibility of refractory organics as a carbon source

Conventional advanced nitrogen removal in municipal wastewater is hindered by the limited availability of carbon sources in the secondary effluent. However, refractory organics present in it had the potential to serve as intrinsic carbon sources after hydrolysis for nitrogen removal via simultaneous denitrification and partial-denitrification anammox (PDA) processes. To assess this potential, a denitrification filter was set up in this study to evaluate its feasibility of concurrent processes. Results showed that increasing influent ammonium (NH4+-N) from 1.0 to 7.0 mg/L increased total nitrogen (TN) removal from 52.4 % to 89.9 %. Simultaneous occurrence of PDA and denitrification process were confirmed by the actual chemical oxygen demand (COD) consumption (0.8-1.2 mg/mg TN removal) from non-fluorescent organics. The presence of the anammox, hydrolytic and denitrifying bacteria further supported the achievement of nitrogen removal through PDA and denitrification processes by utilizing hydrolytic products biodegraded from refractory organics.

Promotion of polyhydroxyalkanoates-producing granular sludge formation by lactic acid using anaerobic dynamic feeding process

To promote the formation of granular sludge with high polyhydroxyalkanoates (PHAs) synthesis ability, an anaerobic dynamic feeding process (AnDF) was proposed. This process combines the feast-famine mode with an anaerobic plug flow feeding process and involving variations in cycle length and settling time. The effects of lactic acid (LA) content (0 %, 20 %, and 40 % COD) on sludge granulation and PHAs production were investigated using three AnDF reactors (R1, R2, and R3). The results showed that the AnDF process feeding with LA not only effectively promoted sludge granulation but also improved its PHAs synthesis ability. The granules were quickly observed in R3 after 50 days of cultivation, with an average diameter of 0.69 mm. The maximum PHAs content reached 47.0 wt% in R3, representing a 30.09 % increase compared to R1. Additionally, extracellular polymeric substances (EPS)-producing bacteria observed in granular sludge may be the prime drivers of the formation of PHAs-producing granular sludge (PHAGS), which was defined as granular sludge with an average particle size larger than 0.30 mm and PHAs content above 40 % cell dry weight (CDW) of sludge samples.

Effect of in situ ultrasonic wave and influent ammonia nitrogen fluctuation on stability of aerobic granular sludge

This study elucidates the impact of fluctuating influent conditions and in situ ultrasonic wave exposure on the stability of aerobic granular sludge (AGS) in the treatment of simulated wastewater emanating from rare earth mining operations. During a stable influent period spanning from Day 1 to Day 95, the seed granules underwent an initial disintegration followed by a re-granulation phase. The secondary granulation was achieved on Day 80 and Day 40 for the ultrasonic reactor (R1) and the control reactor (R2), respectively. Notably, granules formed in R1 exhibited a more porous structure compared to those generated in R2. Subsequently, when the ammonia nitrogen in the influent oscillated between 100 and 500 mg/L during Days 96-140, both reactors yielded compact and densely structured granules. Nitrogen removal profiles were comparable between the two reactors: the removal efficiencies for ammonia nitrogen and total inorganic nitrogen escalated from 95% and 80%, respectively, during Days 1-95, to 95% and 90%, respectively, post-Day 140. A suite of performance metrics indicated that steady-state granules from R1 outperformed those from R2 across several parameters. Specifically, the nitrification/denitrification rates, and relative abundance of denitrifying bacteria were all higher in granules from R1. Conversely, the relative abundance of nitrifying bacteria was comparable between granules from both reactors. However, R1 granules demonstrated lower sludge concentration and smaller average particle size than their R2 counterparts. In conclusion, the AGS system demonstrated robust resilience to fluctuating ammonia nitrogen, and the application of ultrasonic waves significantly enhanced granular activity while achieving in situ sludge reduction.

Distribution of extracellular adhesins in environmental biofilms and flocs: Reimagining the microbial structure

Extracellular cellular adhesins facilitate microbial aggregation; however, most of the information about extracellular adhesins is based on pure culture studies. In this study, we characterized the hydrophobic characteristics and distribution of the extracellular adhesins in environmental biofilms and flocs. The hydrophobic characteristics of the extracellular adhesins were studied by sonicating the microbial aggregates to disperse the cells and by fractionating them using the microbial adhesion to the hydrocarbon method. Furthermore, we probed environmental biofilms and flocs using immunohistochemistry coupled with confocal laser scanning microscopy for reimaging the microbial aggregates based on extracellular adhesins. Small flocs have a relatively dispersed distribution of extracellular adhesins (flagella, fimbriae, pili, and amyloid adhesins). The stratified distribution of extracellular adhesins was observed in environmental biofilms. It was observed that the pili and amyloid adhesins were predominantly present in the core of biofilms, whereas flagella and fimbriae were present in the outer layer of the microbial aggregates. The dispersion of microbial aggregates is one of the limiting factors that challenge the sustainable application of wastewater treatment processes. Greater attention to the components of extracellular protein (such as the adhesins) is required to understand the aggregation of dispersible environmental microbial aggregates.

Stability of aerobic granular sludge for treating inorganic wastewater with different nitrogen loading rates

This paper investigated the effect of nitrogen loading rates (NLRs) on the stability of aerobic granular sludge (AGS) for treating simulated ionic rare earth mine wastewater with high ammonia nitrogen and extremely low organic content. Mature AGS from a sequencing batch reactor (SBR) was seeded into five identical SBRs (R1, R2, R3, R4 and R5). The five reactors were operated with different NLRs (0.2, 0.4, 0.8, 1.2 and 1.6 kg/m3·d). After 30 days of operation, R1, R2 and R5 were dominated by broken granules, while most of the granules in R3 and R4 still maintained a complete structure. The properties of granules from R1, R2, R3, R4 and R5 deteriorated to varying degrees, while the granules from R3 and R4 showed better stability than that from R1, R2 and R5. In R1, R2, R3 and R4, the steady-state ammonia nitrogen removal efficiencies were all greater than 90%, and the steady-state removal efficiencies of total inorganic nitrogen (TIN) were approximately 30%. In R5, the removal efficiencies of ammonia nitrogen and TIN were both approximately 70%. The dominant nitrifying and denitrifying bacterial genera of the granules from the five reactors were Nitrosomonas and Thauera, respectively, and their relative abundance was much higher in granules from R3 and R4. The results demonstrated that a relative equilibrium between the growth and metabolism of nitrifying/denitrifying bacteria was achieved when NLR was between 0.8 and 1.2 kg/m3·d, which could provide technical support for the stability maintenance of AGS in the treatment of ionic rare earth mine wastewater.

Influence of temperature on performance and mechanism of advanced synergistic nitrogen removal in lab-scale denitrifying filter with biogenic manganese oxides

Temperature is a significant operational parameter of denitrifying filter (DF), which affects the microbial activity and the pollutants removal efficiency. This study investigated the influence of temperature on performance of advanced synergistic nitrogen removal (ASNR) of partial-denitrification anammox (PDA) and denitrification, consuming the hydrolytic and oxidation products of refractory organics in the actual secondary effluent (SE) as carbon source. When the test water temperature (TWT) was around 25, 20, 15 and 10 °C, the filtered effluent total nitrogen (TN) was 1.47, 1.70, 2.79 and 5.52 mg/L with the removal rate of 93.38%, 92.25%, 87.33% and 74.87%, and the effluent CODcr was 8.12, 8.45, 10.86 and 12.29 mg/L with the removal rate of 72.41%, 66.17%, 57.35% and 51.87%, respectively. The contribution rate of PDA to TN removal was 60.44%∼66.48%, and 0.77-0.96 mg chemical oxygen demand (CODcr) was actually consumed to remove 1 mg TN. The identified functional bacteria, such as anammox bacteria, manganese oxidizing bacteria (MnOB), hydrolytic bacteria and denitrifying bacteria, demonstrated that TN was removed by the ASNR, and the variation of the functional bacteria along the DF layer revealed the mechanism of the TWT affecting the efficiency of the ASNR. This technique presented a strong adaptability to the variation of the TWT, therefore, it has broad application prospect and superlative application value in advanced nitrogen removal of municipal wastewater.

Phosphate recovery from urban sewage by the biofilm sequencing batch reactor process: Key factors in biofilm formation and related mechanisms

The biofilm sequencing batch reactor (BSBR) technique has been deployed in the laboratory to enrich phosphorus from simulated wastewater, but it is still not clear what its performance will be when real world sewage is used. In this work, the effluent from the multi-stage anoxic-oxic (AO) activated sludge process at a sewage plant was used as the feed water for a BSBR pilot system, which had three reactors operating at different levels of dissolved oxygen (DO). The phosphorus adsorption and release, the biofilm growth, and the extracellular polymeric substances (EPS) components and contents were examined. The microbial communities and the signaling molecules N-acyl-l-homoserine lactones (AHLs) were also analyzed. Gratifyingly, the BSBR process successfully processed the treated sewage, and the biofilm developed phosphorus accumulation capability within 40 days. After entering stable operation, the system concentrated phosphate from 2.59 ± 0.77 mg/L in the influent to as much as 81.64 mg/L in the recovery liquid. Sludge discharge had profound impacts on all aspects of BSBR, and it was carried out successfully when the phosphorus absorption capacity of the biofilm alone was comparable to that of the reactor containing the activated sludge. Shortly after the sludge discharge, the phosphate concentration of the recovery liquid surged from 50 to 140 mg/L, the biofilm thickness grew from 20.56 to 67.32 μm, and the diversity of the microbial population plunged. Sludge discharge stimulated Candidatus competibacter to produce a large amount of AHLs, which was key in culturing the biofilm. Among the AHLs, both C10-HSL and 3OC12-HSL were significantly positively correlated with EPS and the abundance of Candidatus competibacter. The current results demonstrated BSBR as a viable option to enrich phosphorus from real world sewage with low phosphorus content and fluctuating chemistry. The mechanistic explorations also provided theoretical guidance for cultivating phosphorus-accumulating biofilms.

Evaluation of aerobic granulation performance bioaugmented with the auto-aggregating bacterium Pseudomonas stutzeri strain XL-2 with heterotrophic nitrification-aerobic denitrification capacity

In this study, the possibility of an auto-aggregating bacterium Pseudomonas strain XL-2 with heterotrophic nitrification-aerobic denitrification capacity for improving granulation and nitrogen removal was evaluated. The results showed that the supplementation of strain XL-2 promoted granulation, making R1 (experimental group with strain XL-2) dominated by granules at 14 d, which was 12 days earlier than R2 (control group without strain XL-2). This was attributed to the promotion of extracellular polymeric substances (EPS) secretion, particularly proteins by adding strain XL-2, thereby improving the hydrophobicity of sludge and altering the proteins secondary structures to facilitate aggregation. Meanwhile, adding strain XL-2 improved simultaneous nitrification and denitrification efficiency of R1. Microbial community analysis indicated that strain XL-2 successfully proliferated in aerobic granule sludge and might induce the enrichment of genera such as Flavobacterium and Paracoccus that were favorable for EPS secretion and denitrification, jointly promoting granulation and enhancing nitrogen removal efficiency.

Effect of electron acceptors on product selectivity and carbon flux in carbon chain elongation with Megasphaera hexanoica

Megasphaera hexanoica is a bacterial strain following the reverse β-oxidation pathway to synthesize caproate (CA) using lactate (LA) as an electron donor (ED) and acetate (AA) or butyrate (BA) as electron acceptors (EA). Differences in the type and concentration of EA lead to distinctions in product distribution and energy bifurcation of carbon fluxes in ED pathways, thereby affecting CA production. In this study, the effect of various ratios of AA, BA, and AA+BA as EA on carbon flux and CA specific titer during the carbon chain elongation in M. hexanoica was explored. The results indicated that the maximum levels of CA were 18.81 mM and 31.48 mM when the molar ratios of LA/AA and LA/BA were 10:1 and 3:1, respectively. Meanwhile, when AA and BA were used as combined EA (LA, AA, and BA molar amounts of 100, 23, and 77 mM), a maximum CA production of 39.45 mM was obtained. Further analysis revealed that the combined EA exhibited a CA production carbon flux of 49 % (4.3 % and 19.5 % higher compared to AA or BA, respectively) and a CA production specific titer of 45.24 mol (80.89 % and 58.51 % higher compared to AA or BA, respectively), indicating that the effective carbon utilization rate and CA production efficiency were greatly improved. Finally, a scaled-up experiment was conducted in a 1.2 L (working volume) automated bioreactor, implying high biomass (optical density at 600 nm or OD600 = 1.809) and a slight decrease in CA production (28.45 mM). A decrease in H2 production (4.11 g/m3) and an increase in CO2 production (0.632 g/m3) demonstrated the appropriate metabolic adaptation of M. hexanoica to environmental changes such as stirring shear.

Salinity stress results in ammonium and nitrite accumulation during the elemental sulfur-driven autotrophic denitrification process

In this study, we investigated the effects of salinity on elemental sulfur-driven autotrophic denitrification (SAD) efficiency, and microbial communities. The results revealed that when the salinity was ≤6 g/L, the nitrate removal efficiency in SAD increased with the increasing salinity reaching 95.53% at 6 g/L salinity. Above this salt concentration, the performance of SAD gradually decreased, and the nitrate removal efficiency decreased to 33.63% at 25 g/L salinity. Approximately 5 mg/L of the hazardous nitrite was detectable at 15 g/L salinity, but decreased at 25 g/L salinity, accompanied by the generation of ammonium. When the salinity was ≥15 g/L, the abundance of the salt-tolerant microorganisms, Thiobacillus and Sulfurimonas, increased, while that of other microbial species decreased. This study provides support for the practical application of elemental sulfur-driven autotrophic denitrification in saline nitrate wastewater.

Responses of antibiotic resistance genes in the enhanced biological phosphorus removal system under various antibiotics: Mechanisms and implications

The effects of antibiotics on the proliferation of antibiotic resistant genes (ARGs) in WWTPs have drawn great attention in recent years. The effects of antibiotics on ARGs in the enhanced biological phosphorus removal (EBPR) system and its mechanisms, however, are still not well understood. In this study, EBPR systems were constructed using activated sludge to investigate the effects of ten commonly detected antibiotics in the environment on the proliferation of ARGs and the mechanisms involved. The results showed that the total abundance of ARGs increased to varying degrees with the addition of different antibiotics (0.05 mmol/L), and the top 30 ARGs increased by 271.1 % to 370.0 %. Mobile genetic elements (MGEs), functional modules, and the bacteria community were consistently related to the changes in ARGs. Refractory antibiotics, in particular, have a stronger promoting effect on transduction in the EBPR system. The insertion sequence common region (ISCR) and transposon (Tnp) were identified as crucial factors in the proliferation of ARGs. Moreover, the risk of polyphosphate accumulating organisms (PAOs) carrying ARGs in the presence of antibiotics should not be ignored. Our findings emphasize the potential efficacy of employing strategies that target the reduction of MGEs, regulation of cellular communication, and management of microbial communities to effectively mitigate the risks associated with ARGs.

Simultaneous removal of phosphorus, zinc, and lead from oligotrophic ecosystem by iron-driven denitrification: Performance and mechanisms

Based on the current situation of complex pollution caused in surface water by oligotrophic condition and heavy metal release from river and lake bottom sediments. This study aimed to achieve the simultaneous removal of nitrate, phosphorus, Zn2+ and Pb2+ through microbial approach. At nitrate concentration of 4.82 mg L-1, carbon to nitrogen ratio of 1.5, pH of 6.0, and Fe2+ concentration of 5.0 mg L-1, the nitrate removal efficiency of Zoogloea sp. FY-6 reached 95.17%. The addition of pollutants under these conditions resulted in 88.76% removal of total phosphorus at 18 h, and 85.46 and 78.59% removal of Zn2+ and Pb2+ respectively, and there was competition for adsorption between Zn2+ and Pb2+. Extracellular polymers and fluorescence excitation-emission substrates confirmed that Fe2+ reduced heavy metal toxicity through promoting bacterial production of secretions and promotes denitrification as a carbon source. Meanwhile, contaminant removal curves and Fourier transform infrared spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy demonstrated the synchronous removal of Zn2+ and Pb2+ mainly through biological action and the formation of nanoscale iron oxides. Biological-iron precipitation also provided adsorption sites for phosphorus. This research provides the theoretical foundation for applying microorganisms to restore oligotrophic source water (rivers and lakes) containing complex pollutants.

Evaluation the role of soluble microbial products for denitrification sludge characteristic under starvation stress

Physiological changes with the assist role of soluble microbial products (SMP) of preserved denitrifying sludge (DS) undergoing long-term stress of starvation under different storage temperature is extremely important. In this study, SMP extracted from DS were added into DS in starvation condition under room temperature (15-20 °C), 4 °C and -20 °C with three different bio-augmentation phases of 10, 15 and 30 days. Experimental results showed that added SMP in room temperature was optimal for preservation of DS under starvation stress with optimized dosage of 2.0 mL mL^-1 sludge and bio-augmentation phase of 10 d. SMP was more effective in maintaining the specific denitrification activity of DS, and it was nearly boosted to 94.1 % of control one due to assist of 2 times SMP addition with 10 days interval of each. Under assist of SMP, extracellular polymeric substances (EPS) secretion was enhanced as the defense layer to withstand starvation stress, and the protein may be utilized as an alternative substrate to gain energy, accelerate electron transport and transfer during denitrification process. This investigation revealed the feasibility of SMP as an economical and robust strategy for preservation of DS.

Advanced synergetic nitrogen removal of municipal wastewater using oxidation products of refractory organic matters in secondary effluent by biogenic manganese oxides as carbon source

Due to the high operational cost and secondary pollution of the conventional advanced nitrogen removal of municipal wastewater, a novel concept and technique of advanced synergetic nitrogen removal of partial-denitrification anammox and denitrification was proposed, which used the oxidation products of refractory organic matters in the secondary effluent of municipal wastewater treatment plant (MWWTP) by biogenic manganese oxides (BMOs) as carbon source. When the influent NH₄⁺-N in the denitrifying filter was about 1.0, 2.0, 3.0, 4.0, 5.0 and 7.0 mg/L, total nitrogen (TN) in the effluent decreased from about 22 mg/L to 11.00, 7.85, 6.85, 5.20, 4.15 and 2.09 mg/L, and the corresponding removal rate was 49.15, 64.82, 69.40, 76.70, 81.36 and 90.58%, respectively. The proportional contribution of the partial-denitrification anammox pathway to the TN removal was 12.00, 26.45, 39.70, 46.04, 54.97 and 64.01%, and the actual COD_cr consumption of removing 1 mg TN was 0.75, 1.43, 1.26, 1.17, 1.08 and 0.99 mg, respectively, which was much lower than the theoretical COD_cr consumption of denitrification. Furthermore, COD_cr in the effluent decreased to 8.12 mg/L with a removal rate of 72.40%, and the removed organic matters were mainly non-fluorescent organic matters. Kinds of denitrifying bacteria, anammox bacteria, hydrolytic bacteria and manganese oxidizing bacteria (MnOB) were identified in the denitrifying filter, which demonstrated that the advanced synergetic nitrogen removal was achieved. This novel technology presented the advantages of high efficiency of TN and COD_cr removal, low operational cost and no secondary pollution.

Potential interactive effect on biomass and bio-polymeric substances of microalgal-bacterial aerobic granular sludge as a valuable resource for sustainable development

The algal/bacterial biomass and extracellular polymeric substances (EPSs) existing in microalgal-bacterial aerobic granular sludge (MB-AGS) offer a promising bioresource. The current review-based paper presents a systematic overview of the compositions and interactions (gene transfer, signal transduction, and nutrient exchange) of microalgal and bacteria consortia, the role of cooperative or competitive partnerships of MB-AGS in the treatment of wastewater and recovery of resource, and the environmental/operational factors affecting their interactions and EPS production. Moreover, a brief notes is given on the opportunities and major challenges of utilizing the microalgal-bacterial biomass and EPS for phosphorus and polysaccharides chemical recovery, renewable energy (i.e. biodiesel, hydrogen, electricity) production. Overall, this compact review will pave the way for developing MB-AGS future biotechnology.

Hierarchical stringent response behaviors of activated sludge system to stressed conditions

The stringent response of activated sludge systems to either stressed or harmful environments is important for the stable operation of activated sludge, which is examined by taking copper ion (Cu²⁺) as a stress model in this study. When weak stress was employed (Cu²⁺ ≤ 2.5 mg/L), the N-acyl-homoserine lactones (AHLs) of C6-, C8-, and C10-HSL increased by 30 %, 13 %, and 127 %, respectively, while the redox sensor green (RSG) intensity decreased by 28 %. Encountering the increased stress (2.5 mg/L < Cu²⁺ ≤ 5 mg/L), bacteria concentration in the supernatant increased by 87 %. However, the respiration rates of autotrophic and heterotrophic bacteria (SOUR_a and SOUR_h) and adenosine triphosphate decreased by 52 %, 18 %, and 27 %, respectively, and the flocs disintegrated with a diameter decreasing from 57 to 51 μm. When the stress became more serious (Cu²⁺ > 5 mg/L), the respiration rates continued to decline, but the quasi-endogenous respiration ratio (R_q/t) increased from 31 % to 47 %. Negligible changes occurred in the endogenous respiration rate (SOUR_e), adenosine diphosphate, and adenosine monophosphate. Based on these results, a hierarchical stringent response model of the activated sludge system to stressed conditions was proposed, and these responses were evaluated by respirogram. The initial response to weak stress was related to the most sensitive signals of quorum sensing and RSG intensity, well described by the quasi-endogenous respiration rate. The adaptive response to increased stress was the proactive migrations of low- and high-nucleic-acid bacteria to the supernatant, causing the looseness and even disintegration of sludge flocs, well described by SOUR_a, SOUR_h, and R_q/t. The lethal response to lethal stress was related to endogenous metabolic processes, well described by SOUR_e. This work provides new insights into understanding the stringent response of activated sludge systems to some stressed conditions. It helps to regulate the stability of activated sludge systems with respirogram technology.

Parametric optimization of additive manufactured biocarrier submerged in sequencing batch reactor for domestic wastewater treatment

The high nutrient concentration in domestic wastewater effluent can endanger the aquatic life via eutrophication. Thus, research have been carried out to prevent harm to aquatic life. In regard biofilm reactors have been successful by far with few limitations. Bio-carrier fabrication of desired shape is one of the limitations. Recently, the invention of additive manufacturing (AM) of object made it feasible to fabricate the desired shape. In this study additive manufactured bio‒carrier (AMB) was printed using AM technique, with high surface area to volume ratio as well as density higher than water. The submerged attach growth sequencing batch biofilm reactor (SAGSBBR) for organic and nutrient removal from domestic wastewater (DWW) was conducted to determine the optimum bio‒carrier filling ratio (FR) and cycle time (CT) by using response surface methodology (RSM) with CT ranging between 12 h and 24 h and FR ranging between 0 and 20%. The maximum chemical oxygen demand (COD), ammonia-nitrogen (NH₄ ⁺‒N), and total phosphorus (TP) removal was 96.8 mg/L, 93.32 mg/L, and 88.89 mg/L respectively, which was achieved in submerged attached growth sequential biofilm batch reactor with 10% FR (SAGSBBR‒10). The optimization study determined the optimal solution of CT and FR to be 17.07 h and 12.38% respectively, with desirability of 0.987. The predicted mean of responses for the optimal solution were 96.64%, 94.40% and 89.94% for COD removal, NH₄ ⁺‒N removal and TP removal, respectively. The rate of biomass attachment at the first stage in SAGSBBR‒10 and SAGSBBR‒20 was about 11.39 mg/carrier.d and 8.64 mg/carrier.d, whereas the highest accumulation achieved was 98.27 mg/carrier and 80.15 mg/carrier respectively. Thus, this study can assist us to achieve sustainable development goal (SDG) 6.

Advanced nitrogen removal performance and microbial community structure of a lab-scale denitrifying filter with in-situ formation of biogenic manganese oxides

Advanced nitrogen removal faces the challenges of high operational cost resulted from the additional carbon source and secondary pollution caused by inaccurate carbon source dosage in municipal wastewater. To address these problems, a novel carbon source was developed, which was the oxidation products of refractory organic matters in the secondary effluent of municipal wastewater treatment plant (MWWTP) by in-situ generated biogenic manganese oxides (BMOs) in the denitrifying filter. In the steady phase, the effluent chemical oxygen demand (COD_cr), NO₃^--N and total nitrogen (TN) in the denitrifying filter 2^# with BMOs was 11.27, 9.03 and 10.36 mg/L, and the corresponding removal efficiency was 54.79%, 51.85% and 48.03%, respectively, which was significantly higher than those in the control denitrifying filter 1^# that the removal efficiency of COD_cr, NO₃^--N and TN was only 32.30%, 28.58% and 29.36%, respectively. Kinds of denitrifying bacteria (Candidatus Competibacter, Defluviicoccus, Dechloromonas, Candidatus Competibacter, Dechloromonas, Pseudomonas, Thauera, Acinetobacter, Denitratisoma, Anaerolineae and Denitratisoma) and anammox bacteria (Pirellula, Gemmata, Anammoximicrobium and Brocadia) were identified in the denitrifying filters 1^# and 2^#, which explained why the actual COD_cr consumption (1.55 and 1.44 mg) of reducing 1 mg NO₃^--N was much lower than the theoretical COD_cr consumption. While manganese oxidizing bacteria (MnOB, Bacillus, Crenothrix and Pedomicrobium) was only identified in the denitrifying filter 2^#. This novel technology presented the advantages of no additional carbon source, low operational cost and no secondary pollution. Therefore, the novel technology has superlative application value and broad application prospect.

Morphological image analysis of biofilm evolution with quantitative analysis in a moving bed biofilm reactor

The quantitative analysis of biomass is essential for the research and application of moving bed biofilm reactors (MBBRs). However, the difficulty in measuring the attached growing biomass hinders the quantitative analysis of biofilm processes. In this study, a pilot-scale MBBR system was established to investigate biofilm evolution. The quantity of active heterotrophic and autotrophic biomass was measured throughout the entire culturing process. The total active biomass reached 250 mg COD/m² when the biofilm attachment and detachment were balanced, and the corresponding autotrophic biomass contributes to as high as 17 % of the total biomass. Furthermore, quantitative image analysis was performed to obtain the thickness and morphological data of the biofilm evolution. Multivariate regression models were constructed based on the morphological data, which provided satisfactory prediction accuracy for the biofilm thickness and maturation. The most suitable carrier spots for biomass quantification and biofilm maturation were suggested. This work provided the life-cycle information of biofilm quantity and morphology of the MBBR, which contributes to the quantitative understanding of biofilm evolution at MBBRs.

Simultaneous nitrification, denitrification and phosphorus removal: What have we done so far and how do we need to do in the future?

Nitrogen and phosphorus contamination in wastewater is a serious environmental concern and poses a global threat to sustainable development. In this paper, a comprehensive review of the studies on simultaneous nitrogen and phosphorus removal (SNPR) during 1986-2022 (538 publications) was conducted using bibliometrics, which showed that simultaneous nitrification, denitrification, and phosphorus removal (SNDPR) is the most promising process. To better understand SNDPR, the dissolved oxygen, carbon to nitrogen ratio, carbon source type, sludge retention time, Cu²⁺ and Fe³⁺, pH, salinity, electron acceptor type of denitrifying phosphorus-accumulating organisms (DPAOs), temperature, and other influencing factors were analyzed. Currently, SNDPR has been successfully implemented in activated sludge systems, aerobic granular sludge systems, biofilm systems, and constructed wetlands; sequential batch mode of operation is a common means to achieve this process. SNDPR exhibits a significant potential for phosphorus recovery. Future research needs to focus on: (1) balancing the competitiveness between denitrifying glycogen-accumulating organisms (DGAOs) and DPAOs, and countermeasures to deal with the effects of adverse conditions on SNDPR performance; (2) achieving SNDPR in continuous flow operation; and (3) maximizing the recovery of P during SNDPR to achieve resource sustainability. Overall, this study provides systematic and valuable information for deeper insights into SNDPR, which can help in further research.

Aerobic granulation and microbial community succession in sequencing batch reactors treating the low strength wastewater: The dual effects of weak magnetic field and exogenous signal molecule

The application of magneto-biological effects in wastewater treatment has been brought under the spotlight recently. This work explored the dual effects of magnetic field (MF) and exogenous N-hexanoyl-l-homoserine lactone (C₆-HSL) on activated sludge granulation. Results showed that exposure to MF and C₆-HSL obviously accelerated the aerobic granulation process and promoted the secretion of extracellular polymeric substances, especially polysaccharides, humic acid-like substances, aromatic proteins, and tryptophan-like substrates. Illumina MiSeq sequencing results indicated that the introduction of MF and C₆-HSL can increase the diversity and richness of microbial community without antagonism, and the biological basis for rapid granulation process in this study was the enrichment of slow-growing bacteria Candidatus_Competibacter. Besides, the overgrowth of filamentous bacteria Thiothrix could be suppressed due to the presence of MF, improving the stabilities of aerobic granular sludge. This study provides a new understanding of the MF and C₆-HSL effects on rapid aerobic granulation when treating the low-strength wastewater.

Effect of external carbon addition and enrofloxacin on the denitrification and microbial community of sequencing batch membrane reactor treating synthetic mariculture wastewater

The effect of sequencing batch membrane bioreactor (SMBR) on external carbon addition and enrofloxacin was investigated to treat synthetic mariculture wastewater. Anoxic/anaerobic and low COD/TN can improve the ammonia oxidation of the system, and the NH₄⁺-N removal efficiency above 99%. External carbon was added and an anoxic environment was set to provide a suitable environment for denitrifying bacteria. When the external carbon source was 50-207 mg/L, the TN removal efficiency (31.82%-37.73%) and the COD of the effluent (28.85-36.58 mg/L) had little change. The partition resistance model showed that cake deposition resistance (R_C,irr) and irreversible resistance (R_PB) were the main components. And with the increase in cleaning times, the fouling rate of membrane components accelerated. Enrofloxacin can promote the TN removal efficiency (45.66%-93.74%) and had a significant effect on TM7a, Cohaesibacter, Vibrio and Phaeobacter.

A review on recovery of extracellular biopolymers from flocculent and granular activated sludges: Cognition, key influencing factors, applications, and challenges

A reasonable recovery of excess sludge may shift the waste into wealth. Recently an increasing attention has been paid to the recycling of extracellular biopolymers from conventional and advanced biological wastewater treatment systems such as flocculent activated sludge (AS), bacterial aerobic granular sludge (AGS), and algal-bacterial AGS processes. This review provides the first overview of current research developments and future directions in the recovery and utilization of high value-added biopolymers from the three types of sludge. It details the discussion on the recent evolvement of cognition or updated knowledge on functional extracellular biopolymers, as well as a comprehensive summary of the operating conditions and wastewater parameters influencing the yield, quality, and functionality of alginate-like exopolymer (ALE). In addition, recent attempts for potential practical applications of extracellular biopolymers are discussed, suggesting research priorities for overcoming identification challenges and future prospects.

Excellent anammox performance driven by stable partial denitrification when encountering seasonal decreasing temperature

Effluent quality deterioration caused by seasonal temperature reductions in wastewater treatment systems using partial anammox technology is a challenge that cannot be ignored. Here, relationships of denitrification and anammox under decreasing temperature were investigated in an anoxic moving bed biofilm reactor (MBBR). Compared with stable partial-denitrification (NO3- → NO2-), the NO2- reduction to N2 was considerably inhibited when the temperature decreased, conversely helping to the competition of NO2- for anammox. Namely, this transformation provided sufficient substrates for anammox bacteria. Although the TIN removal decreased slightly, anammox contribution was robustly maintained at 91.3 ± 6.6 %, even increased. High-throughput sequencing results revealed that anammox bacteria were enriched (0.56 % to 1.22 %). Moreover, qPCR results showed that increased ratio of hzsB/(nirK + nirS) further supported anammox gained an enhancement. This study demonstrated partial-denitrification/anammox process using anoxic MBBR could maintain stable autotrophic nitrogen removal contribution when encountering temperature decrease, providing a new perspective on the application of mainstream anammox.

Simultaneous nitrification-denitrification in biofilm systems for wastewater treatment: Key factors, potential routes, and engineered applications

Simultaneous nitrification-denitrification (SND) is an advantageous bioprocess that allows the complete removal of ammonia nitrogen through sequential redox reactions leading to nitrogen gas production. SND can govern nitrogen removal in single-stage biofilm systems, such as the moving bed biofilm reactor and aerobic granular sludge system, as oxygen gradients allow the development of multilayered biofilms including nitrifying and denitrifying bacteria. Environmental and operational conditions can strongly influence SND performance, biofilm development and biochemical pathways. Recent advances have outlined the possibility to reduce the carbon and energy consumption of the process via the "shortcut pathway", and simultaneously remove both N and phosphorus under specific operational conditions, opening new possibilities for wastewater treatment. This work critically reviews the factors influencing SND and its application in biofilm systems from laboratory to full scale. Operational strategies to enhance SND efficiency and hints to reduce nitrous oxide emission and operational costs are provided.

Distinct bacterial communities and resistance genes enriched by triclocarban-contaminated polyethylene microplastics in antibiotics and heavy metals polluted sewage environment

Knowledge gaps still surround the question of what biofilms form on contaminated microplastics (MPs) in the antibiotics and (or) heavy metals polluted sewage. In this work, the clean polyethylene microplastics (PE MPs) and triclocarban (TCC)-contaminated PE MPs were cultured in the sewage containing only ampicillin (AMP), only copper (Cu) and both AMP and Cu for 28 days. The results showed that the TCC on PE MPs (with concentration of 2.48 mg/g PE MPs) did not impede the adhesion of the bacteria and the formation of biofilm. Moreover, many potential pathogenic bacteria (Aquabacterium and Pseudoxanthomonas) and potential resistant bacteria (Stenotrophomonas) were more likely to attach on TCC-contaminated PE MPs compared with clean PE MPs. In addition, biofilms of TCC-contaminated PE MPs had highest potential pathogenic functions. TCC-contaminated PE MPs also caused the increases of various resistance genes in both biofilm and sewage. The co-occurrence of TCC, AMP and Cu might exert a stronger selective pressure on bacterial communities and promote the co-selection of resistance genes. In addition, TCC-contaminated PE MPs resulted in higher abundance of five mobile genetic elements (MGEs) (intI1, intI3, tnpA-04, IS613 and trb-C) in sewage, which might further promote the transmission of resistance genes.

Understanding the effect of residual aluminum salt coagulant on activated sludge in sequencing batch reactor: Performance response, activity restoration and microbial community evolution

To investigate the effect of residual coagulant after coagulation pretreatment on activated sludge system of wastewater treatment plants (WWTPs), comparative evaluation of lab-scale sequencing batch reactors under different poly-aluminum chloride (PAC) concentrations (20 and 55 mg/L), presenting the performance differences of reactors. Results showed that the PAC concentration of 20 mg/L slightly enhanced the average removal efficiencies of chemical oxygen demand (COD) and total nitrogen (TN), up to 93.43% and 72.52%. Whereas, an inhibition effect was exerted at the PAC concentration of 55 mg/L, the average removal efficiencies decreased to 88.56% and 57.80% respectively. Similarly, the residual aluminum salts showed a concentration effect of low promotion and high inhibition on sludge activity index. The content of specific oxygen utilization rate (SOUR) and dehydrogenase (DHA) sharply decreased by 30.17% and 53.56% under the high PAC concentration of 55 mg/L. Activity recovery phase showed that the suppression of aluminum salt coagulant on biological system was reversible. High-throughput sequencing presented that the relative abundance of microbes showed obvious variations at different PAC concentrations, and certain bacteria in Chloroflexi and Bacteroidota exhibited better adaptability to the high PAC concentration environment. Nevertheless, the antagonism action between denitrifying genera and other genera as well as the downregulation of functional enzymes regarding nitrogen metabolism gave rise to the deterioration of denitrification under the high PAC concentration of 55 mg/L. This study revealed the influence mechanism of residual aluminum salt coagulant on activated sludge system, providing strategies for efficient decontamination and long-term stable operation of biological system in wastewater treatment plant under the condition of adding PAC.

Application of autothermal thermophilic aerobic digestion as a sustainable recycling process of organic liquid waste: Recent advances and prospects

Autothermal thermophilic aerobic digestion (ATAD) has been used to stabilize organic waste since the 1960s and is considered sustainable technology. ATAD has several advantages, including high biodegradation efficiency, pathogen inactivation, and ease of operation. Although ATAD research has a long history, the number of studies on ATAD is much lower than those on similar aerobic processes, particularly composting. Previous review articles addressed the origin, design, operational experiences, metabolism, and the microorganisms at the thermophilic stage of ATAD. This article reviews the digestion systems, applications, and characteristics of ATAD; compares system performance and microbial community structure of ATAD with those of other biological processes such as composting, activated sludge, and anaerobic digestion; and discusses the physicochemical properties and factors of ATAD. The challenges, opportunities, and prospects for the application of ATAD are also discussed. This review suggests that ATAD is feasible for treating organic liquid waste (1-6% total solid content) in small-sized towns and can help establish a sustainable society.

Biologically induced phosphate precipitation in heterotrophic nitrification processes of different microbial aggregates: Influences of nitrogen removal metabolisms and extracellular polymeric substances

Phosphorus (P) removal occurred in heterotrophic nitrification process, but its mechanism has not been fully explored. In this study, the P removal performances, pathways, and mechanisms in heterotrophic nitrification processes of different microbial aggregates (activated sludge and biofilm) were investigated. The results showed that the biofilm reactor had more efficient total nitrogen removal (98.65%) and phosphate removal (94.17%). Heterotrophic nitrification and denitrification processes generated alkalinity for biologically induced phosphate precipitation (BIPP), which contributed to 64.12%-78.81% of the overall P removal. The solid phase P content reached 48.03 mg/gSS with hydroxyapatite and calcium phosphate formation. The study clarified that biofilm was beneficial to BIPP because of the nitrogen removal metabolism and extracellular polymeric substance (EPS). Heterotrophic nitrogen removal metabolism was the driving force of BIPP, while EPS with abundant carboxyl and amide groups promoted the precipitation. The study would provide new insights into simultaneous nutrients removal and P recovery from wastewater.

Steel pickling rinse wastewater treatment by two-stage MABR system: Reactor performance, extracellular polymeric substances (EPS) and microbial community

A bench-scale two-stage membrane-aerated biofilm reactor (MABR) system was applied to treat steel pickling rinse wastewater with high salinity and refractory organic. The effects of salinity and aeration pressure on the treatment efficiency, extracellular polymeric substances (EPS) characteristics and microbial community structure were studied. The optimal removal efficiencies of COD, NH+ 4-N and TN reached to 62.84%, 99.57% and 51.65%, respectively. Shortcut nitrification was achieved at low aeration, and the salinity less than 4% did not remarkable affect system performance. Colorimetric determination, three-dimensional exaction-emission matrix (3D-EEM) and Fourier transform infrared spectrum (FTIR) were employed to characterize the content and composition of proteins (PN) and polysaccharides (PS) in EPS of the biofilm. The results indicated that PN, not PS, response to changes of environmental conditions played a key role. Moreover, EPS might alleviate intracellular and extracellular osmotic pressure imbalance induced by high salinity, which imparted the biofilm in MABR with prominent salt-tolerant. High-throughput sequencing displayed that nitrifiers (Nitrosomonas, Nitrospira), denitrifiers (Dechloromonas, Hyphomicrobium, Denitromonas, Denitratisoma, Candidatus_Competibacter) and aerobic denitrifiers (Pseudomonas, Thauera) were predominant salt-tolerant bacteria.

Enhanced aerobic granulation for treating low-strength wastewater in an anaerobic-aerobic-anoxic sequencing batch reactor by selecting slow-growing organisms and adding carriers

The aerobic granular sludge (AGS) process is a promising technology for wastewater treatment. However, a long start-up period for granulation and instability during long-term operation still hinder the application of AGS technology, especially for low-strength wastewater. To solve these two problems, this study tested a novel strategy involving the selection of slow-growing organisms and the addition of carriers in an anaerobic-aerobic-anoxic sequencing batch reactor (AN/O/AX_SBR). Three identical AN/O/AX_SBRs (R_Ctrl, R_CCM, and R_GAC), fed with low-strength wastewater, were operated for 120 days. R_Ctrl had no carriers, R_CCM contained cell culture microcarriers (CCM), and R_GAC contained granular activated carbon (GAC). Mature AGS was achieved within 80 days in all reactors. The carriers could reduce the maturation period of AGS by approximately 10 days (76, 66, and 69 days in R_Ctrl, R_CCM, and R_GAC, respectively) and improve the physical strength of the AGS. AGS showed a strong structure without excessive proliferation of filamentous bacteria, full-grown size (900-1100 μm), and good settleability (SVI₅ was 15.4-19.4 mL/g). Microbiological analysis showed that AN/O/AX_SBRs can provide a metabolic selective pressure to select slow-growing organisms such as nitrifying bacteria (norank_f__NS9_marine_group, Ellin6067, and Nitrospira), glycogen and phosphorus accumulating organisms (GAOs: Candidatus_Competibacter and Defluviicoccus; PAOs: Candidatus_Accumulibacter and Flavobacterium). All reactors showed good performance for simultaneous nitrification, endogenous denitrification, and phosphorus removal. The removal efficiencies of total nitrogen and total phosphorous were above 70% and 80%, respectively. The cycle test showed intermediate PAO-GAO metabolism prevailed in the system, and endogenous denitrification was primarily carried out by denitrifying GAOs.

Triclocarban shifted the microbial communities and promoted the spread of antibiotic resistance genes in nitrifying granular sludge system

Triclocarban (TCC) is in great market demand especially after the outbreak of COVID-19 pandemic, becoming an emerging pollutant. However, the impacts of TCC on the performance of nitrifying granular sludge system and the occurrence of antibiotic resistance genes (ARGs) were still unknown. This work explored the impacts of different concentrations of TCC on nitrifying granular sludge. Results showed that TCC suppressed the activities of ammonia-oxidizing microorganisms and decreased the abundance of Nitrospira. Adsorption was the main way for the removal of TCC and the biodegradation efficiency of TCC increased to 28.00% under 19.70 mg/L TCC addition. TCC enriched the ARGs and promoted the risks of their transferring in microorganisms. Pseudomonas might not only have strong resistance to TCC, but also propagate ARGs. The removal process of TCC and bacterial communities were important factors to promote the spread of ARGs. Thus, the existence of TCC presented a great environmental risk.

Denitrifying bacteria immobilized magnetic mycelium pellets bioreactor: A new technology for efficient removal of nitrate at a low carbon-to-nitrogen ratio

This study integrated spores and magnetite (Fe₃O₄) to form magnetic mycelium pellets (MMP) as bio-carriers immobilized with denitrifying bacteria in a bioreactor. Different carbon-to-nitrogen (C/N) ratios and hydraulic retention time (HRT) were established for investigating the performance of the bioreactor. The nitrate removal efficiency was 98.14% at C/N = 2.0 and HRT = 6 h. Gas chromatography (GC) results indicated that the main component of the produced gas was N₂. Fe₃O₄ was well-integrated into MMP according to X-ray diffraction (XRD) results and infrared spectrometer (FTIR) analysis. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that bacteria were successfully immobilized on MMP. Fluorescence excitation-emission matrix (EEM) indicated that functional bacteria GF2 might enhance the metabolic activity of the microbial community in the bioreactor and microbial activity was highest at C/N = 2.0. Pseudomonas stutzeri sp. GF2 might be immobilized and had a major role in the bioreactor according to high throughput sequencing results.

Reproducibility of Aerobic Granules in Treating Low-Strength and Low-C/N-Ratio Wastewater and Associated Microbial Community Structure

Long-term stability of the aerobic granular sludge system is essentially based on the microbial community structure of the biomass. In this study, the physicochemical and microbial characteristics of sludge and wastewater treatment performance were investigated regarding formation, maturation, and long-term maintenance of granules in two parallel sequencing batch reactors (SBR), R1 and R2, under identical conditions. The aim was to explore the linkage between microbial community structure of the aerobic granules, their long-term stability, as well as the reproducibility of granulation and long-term stability. The two reactors were operated with a COD concentration of 400 mg/L and a chemical oxygen demand to nitrogen (COD/N) ratio of 4:1 under anoxic–oxic conditions. It was found that although SVI30, sludge size, and distributions in R1 and R2 were different, aerobic granules were formed, and they maintained long-term stability in both reactors for 320 days, implying that a certain level of randomness of granulation does not affect the long-term stability and performance for COD and N removal. In addition, a significant reduction in the richness and diversity of microbial production was observed after the sludge was converted from inoculum or flocs to granules, but this did not negatively affect the performance of wastewater treatment. Among the predominant microbial species in aerobic granules, Zoogloea was identified as the most important bacteria present during the whole operation with the highest abundance, while Thauera was the important genus in the formation and maturation of the aerobic granules, but it cannot be maintained long-term due to the low food-to-microorganisms ratio (F/M) in the system. In addition, some species from Ohtaekwangia, Chryseobacterium, Taibaiella, and Tahibacter were found to proliferate strongly during long-term maintenance of aerobic granules. They may play an important role in the long-term stability of aerobic granules. These results demonstrate the reproducibility of granulation, the small influence of granulation on long-term stability, and the robustness of aerobic granulation for the removal of COD and N. Overall, our study contributes significantly to the understanding of microbial community structure for the long-term stability of aerobic granular sludge in the treatment of low-COD and low-COD/N-ratio wastewater in practice.

Tetracycline removal in granulation: Influence of extracellular polymers substances, structure, and metabolic function of microbial community

Tetracycline is a potentially hazardous residual antibiotic detected in various sewages. High concentration (mg/L) of tetracycline is found in pharmaceutical/hospital wastewater and wastewater derived from livestock and poultry. So far, only antibiotics in μg/L level have been reported in granulation of aerobic sludge during wastewater treatment, but its effects in high concentration are rarely reported. In this study, the influence of tetracycline in high concentration (∼2 mg/L) on the formation of granular sludge, structure, and metabolic function of the microbial community during the granulation of aerobic sludge was investigated to improve the understanding of the aerobic granular sludge formation under high-level of tetracycline. The role of extracellular polymers substances (EPSs) derived from granular sludge in the granulation and tetracycline removal process was also investigated, showing that tetracycline improved the relative hydrophobicity, flocculability and protein/polysaccharide ratio of EPSs, accelerating the granulation of sludge. Succession of microbial communities occurred during the domestication of functional bacteria present in the sludge and was accompanied with regulation of metabolic function. The addition of tetracycline lead to an increase of tetracycline-degrading bacteria or antibiotic resistance genus. Those findings provide new perspectives of the influence of tetracycline on aerobic sludge granulation and the removal mechanism of tetracycline.

Role of carrier characteristics affecting microbial density and population in enhanced nitrogen and phosphorus removal from wastewater

This research aims to improve simultaneous nitrification-denitrification and phosphorus removal (SNDPR) using novel carriers and to demonstrate the effect of carrier characteristics on nutrient removal in a biofilm reactor. For this purpose, biofilms enriched with both polyphosphate-accumulating organisms (PAOs) and nitrifiers were cultivated in two parallel sequencing batch reactors containing conventional moving bed bioreactor carriers (MBBR) and a novel type of carriers (carbon-based moving carriers (CBMC)). The new carriers were produced based on recycled waste materials via a chemical-thermal process and their specific surface area were 10.4 times higher than typical MBBR carriers of similar dimensions. The results showed that the use of CBMC carriers increased bacterial adhesion by about 18.5% and also affected the microbial population inside the biofilms, leading to an increase in PAOs abundancy and thus an increase in biological phosphorus removal up to 12.5%. Additionally, it was corroborated that the volume of the anoxic zones with dynamic behavior is strictly influenced by the carrier structure and biofilm thickness due to a limitation in oxygen penetration. Accordingly, the formation of broader anoxic zones and shrinkage of these zones to a lesser extent resulted in the continuation of anoxic reactions for longer periods using the novel carriers. Thereby, an increase in nitrogen removal by about 15% was obtained mainly by denitrifying PAOs. The results also exhibited that a higher simultaneous nitrification-denitrification (SND) efficiency can be achieved by selecting an appropriate aeration program influencing the dynamic changes of anoxic zones. Overall, a biofilm system using the new carriers, with phosphorus and nitrogen removal efficiencies of 97.5% and 92.3%, was presented as an efficient, compact, and simple operation SNDPR process.

Three-compartment septic tanks as sustainable on-site treatment facilities? Watch out for the potential dissemination of human-associated pathogens and antibiotic resistance

Improved sanitation is critical important to reduce the spread of human deposited pathogens and antibiotic resistance genes (ARGs). In the China's rural "Toilet Revolution", three-compartment septic tanks (SPTs) are widely used as household domestic sewage treatment facilities. The effluents of SPTs are encouraged to be used as fertilizer in agriculture. However, whether SPT could eliminate fecal pathogens and ARGs is still unrevealed which is crucial in risk assessment of SPT effluent utilization. Herein, we employed metagenomic sequencing to investigate the pathogens and ARGs in rural household SPTs from Tianjin, China. We found that rural household SPT effluents conserved pathogens comparable to that of the influents. A total of 441 ARGs conferring resistance to 26 antibiotic classes were observed in rural household SPTs, with the relative abundance ranging from 709 to 1800 ppm. Results of metagenomic assembly indicated that some ARG-MGE-carrying contigs were carried by pathogens, which may pose risk to human and animal health after being introduced to the environment. This study raises the question of SPTs as sustainable on-site treatment facilities for rural domestic sewage and underscores the need for more attention to the propagation and dissemination of antibiotic-resistant pathogens from SPT to the environments, animals, and humans.

Effect of carbon source on nitrous oxide emission characteristics and sludge properties during anoxic/aerobic wastewater treatment process

Carbon sources are an important parameter in wastewater treatment processes and are closely related to treatment efficiency and nitrous oxide (N₂O) emissions. In this study, three parallel sequencing batch reactors (SBRs) were processed with acetic acid, propionic acid, and a 1:1 mixture of both acids (calculated in COD) to study the effect of carbon sources on N₂O generation and sludge properties (including intracellular polymer content, extracellular polymeric substance (EPS) composition, particle size distribution, settleability, and microbial community structure). The results showed that the highest COD, NH₄⁺-N, and TP removal efficiencies (92.2%, 100%, and 82.3%, respectively) were achieved by the reactor with mixed acid as the carbon source, whereas the reactor using acetic acid had the highest TN removal rate (82.6%) and the lowest N₂O-N conversion rate (1.4%, based on TN removal). The reactor with the carbon source of mixed acid produced the highest polyhydroxyalkanoate (PHA) content, which led to an increase in N₂O generation from the aerobic denitrification pathway. The SBR with mixed acid carbon source also had the highest concentration of EPS, which resulted in the largest particle size and the lowest settleability of sludge flocs among the SBRs. Microbial analysis results revealed that the difference in carbon sources resulted in a variation in the microbial community as well as in the relative abundances of functional microbes involved in biological nitrogen removal processes. The mixed acid promoted the development of ammonia-oxidizing bacteria (AOB), which conducted the primary N₂O generation pathway of aerobic denitrification bioreactions. The carbon source of acetic acid promoted the growth of denitrifying bacteria (DNB), which led to the highest TN removal rate. This study provides a comprehensive understanding of the effects of carbon sources on N₂O generation and sludge properties for WWTPs.

Enhanced proteins and amino acids production based on ammonia nitrogen assimilation and sludge increment by the integration of bioadsorption with anaerobic-anoxic-oxic (AAO) process

Poor effect of contaminants removal efficiency and low organic matter content of activated sludge are common in wastewater treatment plants (WWTPs) in China due to the low-strength wastewater. An anaerobic-anoxic-oxic (AAO) and an adsorption/AAO (A/AAO) combined system were established simultaneously to conduct a comparative study for realizing the conversion of carbon source in influent and the enrichment and recovery of proteins and amino acids through the assimilation of ammonia nitrogen. The experimental results showed that 63.5% of the organic matter in influent was adsorbed and flocculated in adsorption process, and the removal rates of chemical oxygen demand, total nitrogen and total phosphorus in A/AAO process were 88.7%, 77.1%, and 93.0% respectively, which were remarkably better than those in AAO process owing to the addition of improved carbon source. Ammonia assimilation rate of A/AAO process was 26.7% higher than that of AAO process, which implied that the ammonia used to synthesize sludge protein was prominently increased. Furthermore, intracellular proteins and amino acids in A/AAO process were 20% higher than those of AAO process, and the quality was equivalent with fish meal or soybean meal as feed. In addition, the microbial community analysis based on 16S rDNA was conducted. Dechloromonas, Zoogloea, Nitrospira, and Flavobacterium were the main genera, and played important roles in nutrient removal and ammonia nitrogen assimilation. The integration of adsorption process was significant to low-strength wastewater treatment and the improvement of excess sludge quality, which is a prospective inspiration for the resource recovery-based wastewater treatment process.

Performance and responses of aerobic granular sludge at different concentrations of graphene oxide after a single administered dose

To investigate the impact of graphene oxide (GO) under different concentrations (0, 50, 100, 150, and 200 mg/L) on aerobic granular sludge (AGS) after a single administered dose, the performance of nitrogen removal, microbial enzymatic activity, extracellular polymeric substances (EPSs), and microbial community structure was analyzed in batch tests. The results showed that the impact of GO concentrations on AGS was dose- and time-dependent. Short-term GO exposure could accelerate the nitrification process of AGS, while relatively concentrations (≥100 mg/L) inhibited the process when present for extended periods of time. The microbial enzymatic activity showed similar tendency. The production of lactate dehydrogenase release (LDH) in 200 mg/L group was increased 48.04% and EPS contents decreased 30.06% compared to the control group at 30th day and showed that high concentrations of GO have toxic effects on AGS. The microbial bacteria responded differently to the stimulation of different concentrations of GO. PRACTITIONER POINTS: GO affected AGS system performance in concentration- and time-dependent manners. The nitrification rate of AGS increased in the short term and reversed over time. Long-term exposure to high GO concentrations caused toxicity to AGS. Different microorganisms had diverse responses to GO concentrations.

Impact of fungal pellets dosage on long-term stability of aerobic granular sludge

The effects of fungal pellets (FPs) dosage on both structural and functional stability of aerobic granular sludge (AGS) were investigated during 200-day operation. Results showed that the AGS induced by low (a dry mass ratio of FPs to seed sludge, 30%) and high FPs dosage (60%) exhibited good morphology integrity during the entire phase of operation, while the filamentous overgrowth and AGS breakup were observed in the control reactor (0% FPs). Moreover, the granules developed at high FPs dosage demonstrated excellent nutrients removal (COD: 93%; NH4⁺-N: 100%; TN: 77%) and stable bioactivity with a maximum specific oxygen uptake rate (SOUR) of 52.6 ± 2.6 mg O₂/(gVSS·h), a value being 12.2% and 26.7% higher than that of 30% and 0% dosage. The microbial community analysis revealed 60% FPs dosage enriched various functional bacteria involved in nutrients removal. This study suggests a sustainable strategy for improving structural and functional stability of AGS.

Lab-scale autothermal thermophilic aerobic digestion can maintain and remove nitrogen by controlling shear stress and oxygen supply system

Autothermal thermophilic aerobic digestion (ATAD) is used to treat human excreta hygienically. We previously reported a unique full-scale ATAD, showing distinctive bacterial community transitions and producing high-nitrogen-content liquid fertilizer; nevertheless, the mechanism remains unclear. One hypothesis involves using a gas-inducing (GI) agitator. We designed a lab-scale GI system and compared it with a disk-turbine (DT) agitator system by mimicking the temperature shift of full-scale ATAD. The agitation system and its agitation speed greatly affected physicochemical properties and bacterial community structure. GI system at 1000 rpm (GI1000; high total carbon removal efficiency, 88.3%), with few nitrifying and denitrifying bacteria, maintained a high ammoniacal nitrogen concentration and had more shared operational taxonomic units related to Acinetobacter sp., Arcobacter sp., and Longimicrobium sp. with the full-scale ATAD compared with the GI system at 490 rpm and DT system at 1000 rpm (DT1000). Furthermore, DT1000, with a high abundance of nitrifying and denitrifying bacteria such as Alcaligenes aquatilis and Pseudomonas caeni, removed 94.7% total nitrogen with 71.9% total carbon removal efficiency. These results suggested that shear stress and oxygen supply system would change the bacterial community structure, thus affected ATAD performances. Consequently, it is possible that ATAD can be applied for not only production of highly nitrogen-containing liquid fertilizer but also extremely nitrogen removal of wastewater.

Role of weak magnetic strength in the operation of aerobic granular reactor for wastewater treatment containing ammonia nitrogen concentration gradient

Weak magnetic field (WMF) and aerobic granular sludge (AGS) technology were both robust technologies in wastewater treatments. In this study, the AGS characteristics and nutrient removal performances were all estimated at the load of 20 to 40 mg/L ammonia nitrogen (NH₄⁺-N) and 0 to 40mT magnetic field. Results showed that 10mT was beneficial for keeping stable structure of granules when increasing NH₄⁺-N load, accompanied with increasing protein (PN) secretion in EPS. Besides, all the total nitrogen (TN) removal rate under 10mT reached above 90%, while they were all less than 80% under other WMF strength when loading with 40 mg/L NH₄⁺-N. Moreover, the simultaneous nitrification and denitrification (SND) efficiency could be enhanced by WMF of 10mT. Illumina MiSeq sequencing showed that NH₄⁺-N load changed the bacterial richness and diversity when the magnetic strength was 10mT. And Candidatus_Competibacter was identified as the main functional genes for effective operation in this system.

Denitrification performance and mechanism of a novel isolated Acinetobacter sp. FYF8 in oligotrophic ecosystem

The main purpose of this study is to isolate and purify oligotrophic denitrifying bacteria, Acinetobacter sp. FYF8, so as to study the denitrification capacity and characteristics in response to oligotrophic ecosystem. The RSM showed that the best denitrification efficiency was 97.90% under 7.58 pH, 20.69 °C temperature, and 2.83 C/N ratio. Nitrogen balance experiments showed that the nitrogen gas conversion ratio was 39.88, 68.85, and 78.79% at 2.0, 2.5, and 3.0 C/N ratio, respectively. According to 3D-EEM, tyrosine, tryptophan and aromatic protein were the metabolites produced by strain FYF8. The concentration of polysaccharide (PS) and proteins (PN) in different types of extracellular polymeric substances (EPS) and the variation trend were quantitatively studied. Different functional groups such as CH₂, C = O, and C-O-C was characterized by FTIR. These findings indicated that the denitrification strategy of strain FYF8 was related to EPS, which might be a reserve carbon storage in carbon scarcity.