CRP detection from serum for chip-based point-of-care testing system

Serum CRP biomarker detection by using carbon nanotube field-effect transistor (CNT-FET) immunosensor

C-reactive protein (CRP) is produced by the liver in response to systemic inflammation caused by bacterial infection, trauma and internal organ failures. CRP serves as a potential biomarker in the precise diagnosis of cardiovascular risk, type-2 diabetes, metabolic syndrome, hypertension and various types of cancers. The pathogenic conditions indicated above are diagnosed by an elevated CRP level in the serum. In this study, we successfully fabricated a highly sensitive and selective carbon nanotube field-effect transistor (CNT-FET) immunosensor for the detection of CRP. The CNTs were deposited on the Si/SiO2 surface, between source-drain electrodes, afterwards modified with well-known linker PBASE and then anti-CRP was immobilized. This anti-CRP functionalized CNT-FET immunosensor exhibits a wide dynamic detection range (0.01-1000 μg/mL) CRP detection, rapid response time (2-3 min) and low variation (<3 %) which can be delivered as a low-cost and rapid clinical detection technology for the early diagnosis of coronary heart disease (CHD). For the clinical applications, our sensor was tested using CRP fortified serum samples and sensing performance was validated using enzyme-linked immune-sorbent assay (ELISA). This CNT-FET immunosensor will be helpful in taking over the complex laboratory-based expensive traditional CRP diagnostic procedures practiced in the hospitals.

A cost-effective smartphone-based device for rapid C-reaction protein (CRP) detection using magnetoelastic immunosensor

C-Reaction protein (CRP) is a marker of nonspecific immunity for vital signs and wound assessment, and it can be used to diagnose infections in clinical medicine. However, measuring CRP level currently requires hospital-based instruments, high-cost reagents, and a complex process, all of which have limited its full capabilities for self-detection, a growing trend in modern medicine. In this study, we developed a novel smartphone-based device using advanced methods of magnetoelastic immunosensing to mitigate these limitations. We combined a system-on-chip (SoC) hardware architecture with smartphone apps to realize the sampling of resonance frequency shift on magnetoelastic chips, which can determine the ultra-sensitivity to mass change caused by the binding of anti-CRP antibody and CRP. Through detecting a multi-group of samples, we found that the resonance frequency shift was linearly proportional to the CRP concentration in the range from 0.1 to 100 μg mL^-1, with a sensitivity of 12.90 Hz μg^-1 mL^-1 and a detection limit of 2.349 × 10^-4 μg mL^-1. Meanwhile, compared with the large-scale instrument used in clinical settings, the performance of our device was stable and significantly more portable, rapid and cost-effective, offering excellent potential for modern home-based diagnosis.

Eu-Chelate Polystyrene Microsphere-Based Lateral Flow Immunoassay Platform for hs-CRP Detection

Inflammation caused by viral or bacterial infection is a major threat to human health globally. Blood C-reactive protein (CRP) has been proven to be a sensitive indicator for the occurrence and development of inflammation. Furthermore, a tiny change of blood CRP concentration may portend chronic diseases; therefore, high-sensitivity CRP (hs-CRP) detection in a quantitative, rapid, user-friendly, and low-cost manner is highly demanded. In this paper, we developed a europium-chelate polystyrene microsphere (EuPSM)-based lateral flow immunoassay (LFIA) integrating with a benchtop fluorescence analyzer for hs-CRP detection. The optimization of the EuPSM-based LFIA was implemented through adjusting the antibody density on EuPSM from 100% to 60% of the saturated density. Finally, the limit of detection of 0.76 pg/mL and detection range of 0.025-250 ng/mL were obtained. Moreover, the clinical application capability of the proposed platform was validated through detecting CRP in clinical serum samples, showing high consistency with the results obtained from the clinical standard method. Hence, the proposed EuPSM-based LFIA has been verified to be well suitable for hs-CRP detection, while also showing great applicability for sensitively and rapidly detecting other biomarkers.

Diagnoses Based on C-Reactive Protein Point-of-Care Tests

C-reactive protein (CRP) is an important part of the immune system's reaction to various pathological impulses such as bacterial infections, systemic inflammation, and internal organ failures. An increased CRP level serves to diagnose the mentioned pathological states. Both standard laboratory methods and simple point-of-care devices such as lateral flow tests and immunoturbidimetric assays serve for the instrumental diagnoses based on CRP. The current method for CRP has many flaws and limitations in its use. Biosensor and bioassay analytical devices are presently researched by many teams to provide more sensitive and better-suited tools for point-of-care tests of CRP in biological samples when compared to the standard methods. This review article is focused on mapping the diagnostical relevance of CRP, the applicability of the current analytical methods, and the recent innovations in the measurement of CRP level.

Buried-Gate MWCNT FET-Based Nanobiosensing Device for Real-Time Detection of CRP

C-reactive protein (CRP), an acute-phase protein synthesized in the liver in response to inflammation, is one of the biomarkers used for the detection of several diseases. Sepsis and cardiovascular diseases are two of the most important diseases for which detection of CRP at very early stages in the clinical range can help avert serious consequences. Here, a CNT-based nanobiosensing system, which is portable and reproducible, is used for label-free, online detection of CRP. The system consists of an aptameric CNT-based field-effect transistor benefiting from a buried gate geometry with Al₂O₃ as a high dielectric layer and can reflect the pro-cytokine concentration. Test results show that the device responds to CRP changes within 8 min, with a limit of detection as low as 150 pM (0.017 mg L^-1). The device was found to have a linear behavior in the range of 0.43-42.86 nM (0.05-5 mg L^-1). The selectivity of the device was tested with TNF-α, IL-6, and BSA, to which the nanosensing system showed no significant response compared with CRP. The device showed good stability for 14 days and was completely reproducible during this period. These findings indicate that the proposed portable system is a potential candidate for CRP measurements in the clinical range.

Development of a Point-of-Care System Based on White Light Reflectance Spectroscopy: Application in CRP Determination

The development of methods and miniaturized systems for fast and reliable quantitative determinations at the Point-of-Care is a top challenge and priority in diagnostics. In this work, a compact bench-top system, based on White Light Reflectance Spectroscopy, is introduced and evaluated in an application with high clinical interest, namely the determination of C-Reactive protein (CRP) in human blood samples. The system encompassed all the necessary electronic and optical components for the performance of the assay, while the dedicated software provided the sequence and duration of assay steps, the reagents flow rate, the real-time monitoring of sensor response, and data processing to deliver in short time and accurately the CPR concentration in the sample. The CRP assay included two steps, the first comprising the binding of sample CRP onto the chip immobilized capture antibody and the second the reaction of the surface immunosorbed CRP molecules with the detection antibody. The assay duration was 12 min and the dynamic range was from 0.05 to 200 μg/mL, covering both normal values and acute inflammation incidents. There was an excellent agreement between CRP values determined in human plasma samples using the developed device with those received for the same samples by a standard diagnostic laboratory method.

A HiPAD Integrated with rGO/MWCNTs Nano-Circuit Heater for Visual Point-of-Care Testing of SARS-CoV-2

Nowadays, the main obstacle for further miniaturization and integration of nucleic acids point-of-care testing devices is the lack of low-cost and high-performance heating materials for supporting reliable nucleic acids amplification. Herein, reduced graphene oxide hybridized multi-walled carbon nanotubes nano-circuit integrated into an ingenious paper-based heater is developed, which is integrated into a paper-based analytical device (named HiPAD). The coronavirus disease 2019 (COVID-19) pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is still raging across the world. As a proof of concept, the HiPAD is utilized to visually detect the SARS-CoV-2 N gene using colored loop-mediated isothermal amplification reaction. This HiPAD costing a few dollars has comparable detection performance to traditional nucleic acids amplifier costing thousands of dollars. The detection range is from 25 to 2.5 × 1010 copies mL-1 in 45 min. The detection limit of 25 copies mL-1 is 40 times more sensitive than 1000 copies mL-1 in conventional real-time PCR instruments. The disposable paper-based chip could also avoid potential secondary transmission of COVID-19 by convenient incineration to guarantee biosafety. The HiPAD or easily expanded M-HiPAD (for multiplex detection) has great potential for pathogen diagnostics in resource-limited settings.

Simultaneous Detection of Inflammatory Biomarkers by SERS Nanotag-Based Lateral Flow Assay with Portable Cloud Raman Spectrometer

Inflammatory biomarkers are closely related to infectious diseases. However, traditional clinical tests of laboratory inspection are unable to achieve rapid and accurate detection of these biomarkers on-site due to shortcomings such as complex experimental operation, expensive equipment, and long test time. Herein, we proposed a lateral flow assay (LFA) strip based on surface-enhanced Raman scattering (SERS) nanotags (SERS-LFA strips) for the simultaneous and quantitative detection of dual infection biomarkers, serum amyloid A (SAA) and C-reactive protein (CRP), respectively. In practice, mesoporous silica (mSiO2)-coated Au nanoparticles (Au NPs) were used as the SERS substrate. Mercaptobenzoic acid (MBA) was embedded in the internal gap between Au NPs and the mSiO2 shell to prepare AuMBA@mSiO2 NPs, onto which SAA and CRP antibodies were modified to prepare two AuMBA@mSiO2 SERS nanotags. The Raman intensities of the test and control lines were simultaneously identified for the qualitative detection of SAA and CRP, with limits of detection (LODs) as low as 0.1 and 0.05 ng/mL for SAA and CRP, respectively. Finally, aiming at point-of-care testing (POCT) applications, we used a smartphone-based portable Raman spectrometer to quantitatively analyze the SERS-LFA strips. The Raman signal could still be accurately detected when the concentration of SAA and CRP was 10 ng/mL, which is lower than the LOD required in clinical practice for most diseases. Therefore, taking into account its simple operation and short analysis time, by using a portable Raman spectrometer which can be equipped with a 5G cloud-based healthcare management system, the current strategy based on SERS-LFA provides the potential for the quick and on-site diagnosis of infectious diseases such as sepsis, which is of great significance for medical guidance on the treatment of widely spread infection-related diseases in remote areas that lack well-developed medical resources.

Dynamic Range Expansion of the C-Reactive Protein Quantification with a Tandem Giant Magnetoresistance Biosensor

In this study, we report a convenient analytical method for a full-range quantification of the C-reactive protein (CRP), a blood biomarker of infection and cardiovascular events. We determine CRP over the entire diagnostically relevant concentration range in undiluted human blood serum in a single test, using a tandem giant magnetoresistance (GMR) sensor. The tandem principle combines a sandwich assay and a competitive assay, which allows for the discrimination of the concentration values resulting from the multivalued dose-response curve ("Hook" effect), which characterizes the one-step sandwich assay at high CRP concentrations. The sensor covers a linear detection range for CRP concentration from 3 ng/mL to 350 μg/mL, the detection limit (s/n = 3) is 1 ng/mL. The prominent features of the chip-based method are its expanded dynamic range and low sample volume (50 μL), and the need for a short measurement time of 15 min. These figures of merit, in addition to the low detection limit equal to the established assay instrumentation, make it a viable candidate for use in point-of-care diagnostics.

Biosensing based on field-effect transistors (FET): Recent progress and challenges

The use of field-Effect-Transistor (FET) type biosensing arrangements has been highlighted by researchers in the field of early biomarker detection and drug screening. Their non-metalized gate dielectrics that are exposed to an electrolyte solution cover the semiconductor material and actively transduce the biological changes on the surface. The efficiency of these novel devices in detecting different biomolecular analytes in a real-time, highly precise, specific, and label-free manner has been validated by numerous research studies. Considerable progress has been attained in designing FET devices, especially for biomedical diagnosis and cell-based assays in the past few decades. The exceptional electronic properties, compactness, and scalability of these novel tools are very desirable for designing rapid, label-free, and mass detection of biomolecules. With the incorporation of nanotechnology, the performance of biosensors based on FET boosts significantly, particularly, employment of nanomaterials such as graphene, metal nanoparticles, single and multi-walled carbon nanotubes, nanorods, and nanowires. Besides, their commercial availability, and high-quality production on a large-scale, turn them to be one of the most preferred sensing and screening platforms. This review presents the basic structural setup and working principle of different types of FET devices. We also focused on the latest progression regarding the use of FET biosensors for the recognition of viruses such as, recently emerged COVID-19, Influenza, Hepatitis B Virus, protein biomarkers, nucleic acids, bacteria, cells, and various ions. Additionally, an outline of the development of FET sensors for investigations related to drug development and the cellular investigation is also presented. Some technical strategies for enhancing the sensitivity and selectivity of detection in these devices are addressed as well. However, there are still certain challenges which are remained unaddressed concerning the performance and clinical use of transistor-based point-of-care (POC) instruments; accordingly, expectations about their future improvement for biosensing and cellular studies are argued at the end of this review.

Recent advances in developing biosensing based platforms for neonatal sepsis

Neonatal sepsis is a bloodstream infection primarily caused by Escherichia coli (E. coli), Group B Streptococcus (GBS), Listeria monocytogenes, Haemophilus influenzae, S. aureus, Klebsiella spp. and non-typhoidal Salmonella bacteria. Neonatal Sepsis is referred as a critical response to the infection in the neonatal period that can lead to the failure of body organs and thereby causing damage to the tissues resulting in death of the neonates. Nearly 4 million deaths across the world are occurred due to neonatal sepsis infections. In order to prevent the bloodstream infections in the neonates, it is indispensable to diagnose the disease properly for appropriate treatment during the point of care. Numerous studies have been reported to identify major biomarkers associated with neonatal sepsis including Serum Amyloid A (SAA), C - reactive protein (CRP), Procalcitonin (PCT) and Lipopolysaccharide-binding protein (LBP). Distinct diagnostic platforms have also been developed detecting the presence of bloodstream infections including electrochemical, potentiometric, and impedimetric sensors. Recently, electrochemical biosensors with the integration of nanomaterials have emerged as a better platform for neonatal sepsis biomarkers detection. This review article summarizes the diverse screening platforms, evaluation parameters, and new advances based on implications of nanomaterials for the development of biosensors detecting neonatal sepsis infections. The review further elucidates the significance and future scope of distinctive platforms which are predominantly associated with detection of neonatal sepsis.

Electroimmunodetection of cardiac C-reactive protein for determining myocardial Injury

C-reactive protein (CRP) is an acute phase reactant to be a marker of inflammation and has been correlated with the cardiac injury. An immunoassay was performed using anti-human CRP antibody on an InterDigitated electrode (IDE) sensor to determine and specify CRP concentration for diagnosing the condition of myocardial inflammation. To promote the detection, gold nanoparticle (GNP) was seeded on the aminated-IDE surface. Anti-CRP was hitched on the GNP-seeded surface and identified the abundance of CRP. The limit of quantification was found as 100 fM, and the higher current response was noticed by increasing CRP concentrations with the sensitivity at 1 pM. Furthermore, CRP-spiked human serum did not interfere the determination of CRP and increased the current response, indicating suitability for a real-life sample. Similarly, the control experiments with nonimmune antibody Troponin I are not showing the definite current responses, proving the selective identification of CRP. This method of diagnosing is needful to determine the cardiovascular injury at the right time.

Design and Electrochemical Characterization of Spiral Electrochemical Notification Coupled Electrode (SENCE) Platform for Biosensing Application

C-reactive protein (CRP) is considered to be an important biomarker associated with many diseases. During any physiological inflammation, the level of CRP reaches its peak at 48 h, whereas its half-life is around 19 h. Hence, the detection of low-level CRP is an important task for the prognostic management of diseases like cancer, stress, metabolic disorders, cardiovascular diseases, and so on. There are various techniques available in the market to detect low-level CRP like ELISA, Western blot, etc. An electrochemical biosensor is one of the important miniaturized platforms which provides sensitivity along with ease of operation. The most important element of an electrochemical biosensor platform is the electrode which, upon functionalization with a probe, captures the selective antibody-antigen interaction and produces a digital signal in the form of potential/current. Optimization of the electrode design can increase the sensitivity of the sensor by 5-10-fold. Herein, we come up with a new sensor design called the spiral electrochemical notification coupled electrode (SENCE) where the working electrode (WE) is concentric in nature, which shows better response than the market-available standard screen-printed electrode. The sensor is thoroughly characterized using a standard Ferro/Ferri couple. The sensing performance of the fabricated platform is also characterized by the detection of standard H2O2 using a diffusion-driven technique, and a low detection limit of 15 µM was achieved. Furthermore, we utilized the platform to detect a low level (100 ng/mL) of CRP in synthetic sweat. The manuscript provides emphasis on the design of a sensor that can offer good sensitivity in electrochemical biosensing applications.

Biosensors for detecting viral and bacterial infections using host biomarkers: a review

A schematic diagram showing multiple modes of biosensing platforms for the diagnosis of bacterial or viral infections.

Development of a Cuvette-Based LSPR Sensor Chip Using a Plasmonically Active Transparent Strip

This research demonstrates the development of a transmission-mode localized surface plasmon resonance (LSPR) sensor chip using a cuvette cell system for the sensitive detection of a biomolecule marker such as C-reactive protein (CRP). In order to develop a highly sensitive LSPR sensor chip, plasmonically active gold nanoparticles (AuNPs) were decorated onto various transparent substrates in the form of a uniform, high-density single layer using a self-assembly process. The transparent substrate surface was modified with amine functional groups via (3-Aminopropyl)triethoxysilane (APTES) treatment, and the ligand concentration and temperature (0.5% APTES at 60°C) were then optimized to control the binding energy with AuNPs. The optimized plasmonically active strip was subsequently prepared by dipping the amine-functionalized substrate into AuNPs for 8 h. The optimized plasmonic strip functionalized with anti-CRP was transformed into a portable LSPR sensor chip by placing it inside a cuvette cell system, and its detection performance was evaluated using CRP as a model sample. The detection limit for CRP using our LSPR sensor chip was 0.01 μg/mL, and the detection dynamic range was 0.01–10 μg/mL with a %CV of <10%, thus confirming its selectivity and good reproducibility. These findings illustrate that the highly sensitive portable LSPR biosensor developed in this study is expected to be widely used in a diverse range of fields such as diagnosis, medical care, environmental monitoring, and food quality control.

Recent advances in biosensors for diagnosis and detection of sepsis: A comprehensive review

Sepsis is one of the leading causes of mortality among critically ill patients globally. According to WHO report 2018, it is estimated to affect beyond 30 million people worldwide every year. It causes loss of human lives, which arise from infection and inflammation and long term stay in intensive care unit (ICU) in hospitals. Despite the availability of satisfactory prognostic markers contributing to the diagnosis of sepsis, millions of people die even after admission to the hospitals. Correct and early diagnosis of sepsis leads to rapid administration of appropriate antibiotics can thus potentially avert the attainment to critical stages of sepsis, thereby saving human lives. Conventional diagnostic practices are costly, time consuming and they lack adequate sensitivity and selectivity, provoking an urgent need for developing alternate sepsis diagnosis systems. Nevertheless, biosensors have the much-treasured scope for reasonable sepsis diagnosis. Advancement in nano-biotechnology has provided new paradigm for biosensor platforms with upgraded features. Here, we provide an overview of the recent advances in biosensors with a brief introduction to sepsis, followed by the conventional methods of diagnosis and bio-sensing. To conclude, a proactive role and an outlook on technologically advanced biosensor platforms are discoursed with possible biomedical applications.

Proton-ELISA: Electrochemical immunoassay on a dual-gated ISFET array

Here we report an electrochemical immunoassay platform called Proton-ELISA (H-ELISA) for the detection of bioanalytes. H-ELISA uniquely utilizes protons as an immunoassay detection medium, generated by the enzyme glucose oxidase (GOx) coupled with Fenton's reagent in a proton amplification reaction cascade that results in a highly amplified signal. A proton-sensitive dual-gated ion-sensitive field effect transistor (DG-ISFET) sensor was also developed for sensitive and accurate detection of the proton signal in H-ELISA. The DG-ISFET sensor comprises of a 128 × 128 array of 16,384 sensing transistors each with an individually addressable back gate to allow for a very high signal throughput and improved accuracy. We then demonstrated that the platform could detect C-reactive protein and immunoglobulin E down to concentrations of 12.5 and 125 pg/mL, respectively. We further showed that the platform is compatible with complex biological sample conditions such as human serum, suggesting that the platform is sufficiently robust for potential diagnostic applications.

Sensors and Biosensors for C-Reactive Protein, Temperature and pH, and Their Applications for Monitoring Wound Healing: A Review

Wound assessment is usually performed in hospitals or specialized labs. However, since patients spend most of their time at home, a remote real time wound monitoring would help providing a better care and improving the healing rate. This review describes the advances in sensors and biosensors for monitoring the concentration of C-reactive protein (CRP), temperature and pH in wounds. These three parameters can be used as qualitative biomarkers to assess the wound status and the effectiveness of therapy. CRP biosensors can be classified in: (a) field effect transistors, (b) optical immunosensors based on surface plasmon resonance, total internal reflection, fluorescence and chemiluminescence, (c) electrochemical sensors based on potentiometry, amperometry, and electrochemical impedance, and (d) piezoresistive sensors, such as quartz crystal microbalances and microcantilevers. The last section reports the most recent developments for wearable non-invasive temperature and pH sensors suitable for wound monitoring.

Dynamic relationship between postoperative infection and CRP, IL-6, and Livin in patients with bone tumors

BACKGROUND

The objective of the present study was to investigate the dynamic relationship between postoperative infection and levels of CRP, IL-6, and Livin in patients with bone tumors.

METHODS

A total of 126 patients with bone tumors admitted to our hospital from November 2013 to October 2015 were randomly selected and retrospectively analyzed. According to whether postoperative infection occurred, patients were divided into the infected group (N.=52) and the non-infected group (N.=74). Before surgery, and on the 1st, 3rd, 5th, 7th, and 10th day after surgery, the levels of serum CRP and IL-6 of patients in both groups were compared; the relative expression levels of Livin protein of patients in both groups were measured by Western blot.

RESULTS

After surgery, the levels of CRP and IL-6 of patients in both groups at all time points were significantly higher than those before surgery and the levels of CRP and IL-6 of the infected group were significantly higher than those of the non-infected group (P<0.05). The levels of CRP and IL-6 reached a peak on the 3rd day after surgery, and CRP declined rapidly. The levels of IL-6 declined slowly. On the 10th day after surgery, the levels of IL-6 of patients in both groups were higher than those before surgery and the levels of IL-6 of patients in the infected group were higher than those of the control group (P<0.05). The levels of Livin protein in patients of both groups were not significantly different (P>0.05).

CONCLUSIONS

The increase of the levels of CRP and IL-6 are closely related to infection. Livin has no close relationship with the occurrence of infection.

AlGaN/GaN High Electron Mobility Transistor-Based Biosensor for the Detection of C-Reactive Protein

In this paper, we propose an AlGaN/GaN high electron mobility transistor (HEMT)-based biosensor for the detection of C-reactive protein (CRP) using a null-balancing circuit. A null-balancing circuit was used to measure the output voltage of the sensor directly. The output voltage of the proposed biosensor was varied by antigen-antibody interactions on the gate surface due to CRP charges. The AlGaN/GaN HFET-based biosensor with null-balancing circuit applied shows that CRP can be detected in a wide range of concentrations, varying from 10 ng/mL to 1000 ng/mL. X-ray photoelectron spectroscopy was carried out to verify the immobilization of self-assembled monolayer with Au on the gated region.

Electrochemical processes and mechanistic aspects of field-effect sensors for biomolecules

Electronic biosensing is a leading technology for determining concentrations of biomolecules. In some cases, the presence of an analyte molecule induces a measured change in current flow, while in other cases, a new potential difference is established. In the particular case of a field effect biosensor, the potential difference is monitored as a change in conductance elsewhere in the device, such as across a film of an underlying semiconductor. Often, the mechanisms that lead to these responses are not specifically determined. Because improved understanding of these mechanisms will lead to improved performance, it is important to highlight those studies where various mechanistic possibilities are investigated. This review explores a range of possible mechanistic contributions to field-effect biosensor signals. First, we define the field-effect biosensor and the chemical interactions that lead to the field effect, followed by a section on theoretical and mechanistic background. We then discuss materials used in field-effect biosensors and approaches to improving signals from field-effect biosensors. We specifically cover the biomolecule interactions that produce local electric fields, structures and processes at interfaces between bioanalyte solutions and electronic materials, semiconductors used in biochemical sensors, dielectric layers used in top-gated sensors, and mechanisms for converting the surface voltage change to higher signal/noise outputs in circuits.

Nanofluidics in point of care applications

Nanofluidics is generally described as the study of liquid flow in or around structures of 100 nm or smaller, and its use for lab on a chip devices has now been actively studied for two decades. Here a brief review is given of the impact that this nanofluidics research has had on point of care applications. Four areas are identified where nanofluidics has brought the largest contributions: single nanopores, nanoporous membranes, nanoconfinement and the use of concentration polarization. The sometimes revolutionary developments in these areas are briefly treated and finally challenges and future perspectives are described.

Prospects and advancements in C-reactive protein detection

C-reactive protein (CRP) is one of the earliest proteins that appear in the blood circulation in most systemic inflammatory conditions and this is the reason for its significance, even after identification of many organ specific inflammatory markers which appear relatively late during the course of disease. Earlier methods of CRP detection were based on the classical methods of antigen-antibody interaction through precipitation and agglutination reactions. Later on, CRP based enzymatic assays came into the picture which were further modified by integration of an antigen-antibody detection system with surface plasma spectroscopy. Then came the time for the development of electrochemical biosensors where nanomaterials were used to make a highly sensitive and portable detection system based on silicon nanowire, metal-oxide-semiconductor field-effect transistor/bipolar junction transistor, ZnS nanoparticle, aptamer, field emission transmitter, vertical flow immunoassay etc. This editorial attempts to summarize developments in the field of CRP detection, with a special emphasis on biosensor technology. This would help in translating the latest development in CRP detection in the clinical diagnosis of inflammatory conditions at an early onset of the diseases.