AC electrokinetics-enhanced capacitive immunosensor for point-of-care serodiagnosis of infectious diseases

Introducing a portable electrochemical biosensor for Mycobacterium avium subsp. paratuberculosis detection using graphene oxide and chitosan

In this contribution, a novel, low-cost, high throughput, and ultra-selective electrochemical DNA nanobiosensor was developed for accurate on-site detection of Mycobacterium avium subspecies paratuberculosis (MAP) in real media for practical diagnosis of Johne's disease (JD). The method was designed based on the immobilization of graphene oxide and chitosan biopolymer on the surface of a glassy carbon electrode, modified by electrochemical immobilization of graphene oxide and chitosan biopolymer, followed by activation of biopolymer via 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride and N-hydroxy succinimide (EDC/NHS) coupling system. Afterward, the commercial probe DNA (ssDNA) was stabilized on the activated electrode surface to prepare an ultra-selective ssDNA-stabilized nanobiosensor for MAP sensing called "ssDNA-stabilized GO-CH-EDC/NHS-modified electrode". Several characterization methods distinguished the bioelectrode. The DNA hybridization between the nanobiosensor and target DNA was confirmed by cyclic voltammetry and differential pulse voltammetry. "At optimal experimental conditions, the nanobiosensor showed a linear range of 1.0 × 10-15-1.0 × 10-12 mol L-1, a detection limit as low as 1.53 × 10-13 mol L-1, and a repeatability with a relative standard deviation (%RSD) of 4.7%. The reproducibility was also appropriate, with a %RSD of about 10%. It was used to diagnose MAP in real samples with highly accurate results. Therefore, the developed nanobiosensor can be used for clinical diagnosis of MAP.

Impedance-Based Neutralizing Antibody Detection Biosensor with Application in SARS-CoV-2 Infection

Although safe and efficacious coronavirus disease-2019 (COVID-19) vaccines are available, real protective immunity is revealed by the serum COVID-19 neutralizing antibody (NAb) concentration. NAbs deactivate the virus by attaching to the viral receptor-binding domain (RBD), which interacts with angiotensin-converting enzyme 2 (ACE2) on the human cell. This paper introduces inexpensive, rapid, sensitive, and quantifiable impedance-based immunosensors to evaluate the NAb. The sensor limit of detection is experimentally determined in different buffer dilutions using bovine IgG-anti-bovine IgG interaction. The dominance of AC electrokinetic transport and molecular diffusion in the sensor is investigated using scaling analysis and numerical simulations. The results demonstrated that the sensor detection mechanism is mainly based on the diffusion of the biomolecules onto the electrode surface. After evaluating the sensor working principles, viral RBD buffers, including different NAb concentrations, are applied to the sensor, immobilized with the human ACE2 (hACE2). Results demonstrate that the sensor is capable of NAb detection in the analytical measuring interval between 45 ng/mL and 185 ng/mL. Since the present sensor provides fast test results with lower costs, it can be used to assess the NAb in people's blood serum before receiving further COVID vaccine doses.

Nucleic Acid Detection with Ion Concentration Polarization Microfluidic Chip for Reduced Cycle Numbers of Polymerase Chain Reaction

Nucleic acid detection is widely used in disease diagnosis, food safety, environmental monitoring and many other research fields. The continuous development of rapid and sensitive new methods to detective nucleic acid is very important for practical application. In this study, we developed a rapid nucleic-acid detection method using polymerase chain reaction (PCR) combined with electrokinetic preconcentration based on ion concentration polarization (ICP). Using a Nafion film, the proposed ICP microfluidic chip is utilized to enrich the nucleic acid molecules amplified by PCR thermal cycles. To demonstrate the capability of the microfluidic device and the hybrid nucleic-acid detection method, we present an animal-derived component detection experiment for meat product identification applications. With the reduced cycle numbers of 24 cycles, the detection can be completed in about 35 min. The experimental results show that this work can provide a microfluidic device and straightforward method for rapid detection of nucleic acids with reduced cycle numbers.

Real-Time and In Situ Monitoring of the Synthesis of Silica Nanoparticles

The real-time and in situ monitoring of the synthesis of nanomaterials (NMs) remains a challenging task, which is of pivotal importance by assisting fundamental studies (e.g., synthesis kinetics and colloidal phenomena) and providing optimized quality control. In fact, the lack of reproducibility in the synthesis of NMs is a bottleneck against the translation of nanotechnologies into the market toward daily practice. Here, we address an impedimetric millifluidic sensor with data processing by machine learning (ML) as a sensing platform to monitor silica nanoparticles (SiO₂NPs) over a 24 h synthesis from a single measurement. The SiO₂NPs were selected as a model NM because of their extensive applications. Impressively, simple ML-fitted descriptors were capable of overcoming interferences derived from SiO₂NP adsorption over the signals of polarizable Au interdigitate electrodes to assure the determination of the size and concentration of nanoparticles over synthesis while meeting the trade-off between accuracy and speed/simplicity of computation. The root-mean-square errors were calculated as ∼2.0 nm (size) and 2.6 × 10¹⁰ nanoparticles mL^-1 (concentration). Further, the robustness of the ML size descriptor was successfully challenged in data obtained along independent syntheses using different devices, with the global average accuracy being 103.7 ± 1.9%. Our work advances the developments required to transform a closed flow system basically encompassing the reactional flask and an impedimetric sensor into a scalable and user-friendly platform to assess the in situ synthesis of SiO₂NPs. Since the sensor presents a universal response principle, the method is expected to enable the monitoring of other NMs. Such a platform may help to pave the way for translating "sense-act" systems into practice use in nanotechnology.

Capacitive Aptasensor Coupled with Microfluidic Enrichment for Real-Time Detection of Trace SARS-CoV-2 Nucleocapsid Protein

The pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has lasted for almost 2 years. Stemming its spread has posed severe challenges for clinical virus detection. A long turnaround time, complicated operation, and low accuracy have become bottlenecks in developing detection techniques. Adopting a direct antigen detection strategy, we developed a fast-responding and quantitative capacitive aptasensor for ultratrace nucleocapsid protein detection based on a low-cost microelectrode array (MEA) chip. Employing the solid-liquid interface capacitance with a sensitivity of picofarad level, the tiny change on the MEA surface can be definitively detected. As a result, the limit of detection reaches an ultralow level of femtogram per milliliter in different matrices. Integrated with efficient microfluidic enrichment, the response time of this sensor from the sample to the result is shortened to 15 s, completely meeting the real-time detection demand. Moreover, the wide linear range of the sensor is from 10-5 to 10-2 ng/mL, and a high selectivity of 6369:1 is achieved. After application and evaluation in different environmental and body fluid matrices, this sensor and the detection method have proved to be a label-free, real-time, easy-to-operate, and specific strategy for SARS-CoV-2 screening and diagnosis.

Enhancement of Binding Kinetics on Affinity Substrates Using Asymmetric Electroosmotic Flow on a Sinusoidal Bipolar Electrode

In the context of the COVID-19 epidemic, enhancing the transport of analyte to a sensor surface is crucial for rapid detection of biomolecules since common conditions, including low diffusion coefficients, cause inordinately long detection times. Integrated microfluidic immunoassay chips are receiving increasing attention for their low sample volume and fast response time. We herein take advantage of asymmetric ICEO flow at a bipolar sinusoidal electrode to improve the rate of antibody binding to the reaction surface based on finite element modeling. Three different microfluidic cavities are proposed by changing the positions of the surface reaction area. We further investigate the relationship between binding enhancement and reaction surface positions, Damkohler number, and the voltage and frequency of the AC signal applied to the driving electrodes. Furthermore, the influence of the AC signal applied to the sinusoidal bipolar electrode on antigen–antibody-binding performance is studied in detail. Above all, the simulation results demonstrate that the microfluidic immune-sensor with a sinusoidal bipolar electrode could not only significantly improve the heterogeneous immunoassays but also enable efficient enhancement of assays in a selected reaction region within the micro-cavity, providing a promising approach to a variety of immunoassay applications, such as medical diagnostics and environmental and food monitoring.

Rapid Detection and Antimicrobial Susceptibility Testing of Pathogens Using AgNPs-Invertase Complexes and the Personal Glucose Meter

Rapid detection of pathogens and assessment of antimicrobial susceptibility is of great importance for public health, especially in resource-limiting regions. Herein, we developed a rapid, portable, and universal detection method for bacteria using AgNPs-invertase complexes and the personal glucose meter (PGM). In the presence of bacteria, the invertase could be released from AgNPs-invertase complexes where its enzyme activity of invertase was inhibited. Then, the enzyme activity of invertase was restored and could convert sucrose into glucose measured by a commercially PGM. There was a good linear relationship between PGM signal and concentration of E. coli or S. aureus as the bacteria model with high sensitivity. And our proposed biosensor was proved to be a rapid and reliable method for antimicrobial susceptibility testing within 4 h with consistent results of Minimum Inhibitory Concentrations (MICs) testing, providing a portable and convenient method to treat infected patients with correct antibiotics and reduce the production of antibiotic-resistant bacteria, especially for resource-limiting settings.

Optimization of ACEK-enhanced, PCB-based biosensor for highly sensitive and rapid detection of bisphenol a in low resource settings

In this study, we developed a low-cost and easy-to-use capacitive biosensor employing printed-circuit-board (PCB)-based technique for electrode fabrication and a specific alternative current (AC) signal for AC Electrokinetics (ACEK) effect excitation. Fast, accurate, and highly sensitive detection and quantification of bisphenol A (BPA) was achieved. An easy characterization of the biofunctionalization process is introduced by measuring interfacial capacitance which is simple and superior to most of methods currently in use. The frequency and amplitude of the AC signal used for capacitive interrogation were optimized to achieve maximum interfacial capacitance and maximum sensitivity. To evaluate the performance of the developed biosensor, its operation was compared with in-house microfabricated and commercially available electrodes. The limit-of-detection (LOD) obtained using the PCB-based electrodes was found to be at least one order of magnitude lower than that obtained with the commercial and in-house microfabricated electrodes. The linear range for BPA detection was wide from 1 fM to 10 pM with an LOD of 109.5 aM and sample to result in 20s. The biosensor operation was validated by spike-and-recovery tests of BPA using commercial food samples. Thus, the platform has a potential as an on-site detection of bisphenol A in low-resource settings.

A disposable aptasensor based on a gold-plated coplanar electrode array for on-site and real-time determination of Cu2

Copper ion (Cu²⁺) is an important cofactor for many enzymes in human body. Either excessive or deficient Cu²⁺ in the body may cause serious dysfunctions and diseases. So sensitive determination of Cu²⁺ in environmental samples is of more significance for evaluation and control of Cu²⁺ intake. Based on a low-cost gold-plated coplanar electrode array, a disposable aptasensor is developed with an ultra-sensitive indicator of interfacial capacitance. Modified with a specially isolated DNA aptamer for Cu²⁺, this sensor achieves a high selectivity of 1207: 1 against non-target ions. To realize real-time response, alternating-current electrothermal effect is integrated into the capacitance measuring process to efficiently enrich the trace Cu²⁺. This sensor reaches a limit of detection of 2.97 fM, with a linear range from 5.0 fM to 50 pM. The response time is only 15 s, which can meet the real-time detection requirement. On-site test of practical samples is also realized using the disposable sensor combined with a handheld inductance/capacitance/resistance meter. This sensor with its portable test system provides a cost-efficient solution for on-site, real-time and sensitive detection of Cu²⁺, showing great application value in environment monitoring.

Enhancing affinity-based electroanalytical biosensors by integrated AC electrokinetic enrichment-A mini review

Biosensors play a central role in moving diagnostics to being on-site or decentralized. Affinity biosensor, an important category of biosensors, has important applications in clinical diagnosis, pharmaceuticals, immunology, and other fields. Affinity biosensors rely on specific binding between target analytes and biological ligands such as antibodies, nucleic acids, or other receptors to generate measurable signals. Oftentimes the target analytes in practical samples are of low abundance in a complex matrix. Traditional affinity biosensors mainly rely on random diffusion of analytes in solution to conjugate with biorecognition elements on the sensor surface of electrodes. The process may take hours or even days, which is not conducive to rapid and sensitive detection of biosensors. Therefore, it is strongly desired to incorporate an enrichment mechanism for target analytes into biosensor-based detection. AC electrokinetic (ACEK) effect can realize rapid enrichment of analytes by application of AC electric fields, which holds great promise for achieving high sensitivity, low detection limit, and rapid turnaround. This article reviews the studies of affinity biosensors integrated with ACEK enrichment in the past decade, and summarizes the latest detection methods, detection devices and applications, hoping to provide some insights and references for researchers in related fields.

Nanomaterials-Based Sensors for Respiratory Viral Detection: A Review

Contagious diseases are the principal cause of mortality, particularly respiratory viruses, a real menace for public health and economic development worldwide. Therefore, timely diagnosis and treatments are the only life-saving strategy to overcome any epidemic and particularly the ongoing prevailing pandemic COVID-19 caused by SARS-CoV-2. A rapid identification, point of care, portable, highly sensitive, stable, and inexpensive device is needed which is exceptionally satisfied by sensor technology. Consequently, the researchers have directed their attention to employing sensors targeting multiple analyses of pathogenic detections across the world. Nanostructured materials (nanoparticles, nanowires, nanobundles, etc.), owing to their unique characteristics such as large surface-to-volume ratio and nanoscale interactions, are widely employed to fabricate facile sensors to meet all the immediate emerging challenges and threats. This review is anticipated to foster researchers in developing advanced nanomaterials-based sensors for the increasing number of COVID-19 cases across the globe. The mechanism of respiratory viral detection by nanomaterials-based sensors has been reported. Moreover, the advantages, disadvantages, and their comparison with conventional sensors are summarized. Furthermore, we have highlighted the challenges and future potential of these sensors for achieving efficient and rapid detection.

A Sensitive and Specific Genomic RNA Sensor for Point-of-Care Screening of Zika Virus from Serum

This work presents a sensitive and specific single-step RNA sensor for Zika virus (ZIKV) in serum. Using AC electrokinetics (ACEK)-enhanced capacitive sensing technology, ZIKV genomic RNA (gRNA) can be directly detected from serum. The sensors are interdigitated electrodes modified with oligonucleotide probes complementary to the conserved regions of ZIKV gRNA. The ACEK capacitive sensing applies an optimized AC excitation signal over the sensor, which induces ACEK microfluidic enrichment of analytes and also simultaneously performs real-time monitoring of hybridization of ZIKV gRNA on the sensor surface. Hence, the sensing procedures are simple with rapid turn-around time and good specificity and sensitivity. A series of experiments are conducted to optimize the sensor performance. The performance of the sensor is investigated for three different probes, two functionalization buffers, and different hybridization buffers. With the optimized sensing protocol, this method can detect spiked ZIKV gRNA from human serum within 30 s and reach a limit of detection of 78.8 copies/μL in analytical samples and as low as 287.5 copies/μL in neat serum. The sensors can successfully differentiate between the RNAs of the ZIKV and dengue virus, two viruses with similar transmission paths and symptoms. The sensor is simple to use and requires no labeling or sophisticated process typically involved in a polymerase chain reaction, hybridization chain reaction, or nucleic acid sequence-based amplification.

Pre-Degassed Microfluidic Chamber-Based Digital PCR Device for Meat Authentication Applications

Droplet digital polymerase chain reaction (ddPCR) suffers from the need for specific equipment and skilled personnel; thus, we here present a chamber-based digital PCR microfluidic device that is compatible with fluorescence image read-out systems and removes bubbles by a pre-degassed microfluidic device that consists of a pilot channel and micro chamber arrays. Digitalized PCR reagents are introduced into micro chambers, and thermocycles are taken to perform a DNA amplification process. Then, fluorescence images of a micro chamber array are read out and analyzed to obtain the total number of positive chambers. Thereby, the copy numbers of target DNA are calculated for quantitative detections. As a validation, this device is evaluated by the application of meat authentication. We performed dPCR tests using DNA templates extracted from a pure mutton DNA template with different dilutions. Then, the dPCR chip was used to identify the meat authentication using mutton–chicken mixtures with different mass ratios, showing its performance in real biotechnical applications.

Single-step label-free nanowell immunoassay accurately quantifies serum stress hormones within minutes

A non-faradaic label-free cortisol sensing platform is presented using a nanowell array design, in which the two probe electrodes are integrated within the nanowell structure. Rapid and low volume (≤5 μl) sensing was realized through functionalizing nanoscale volume wells with antibodies and monitoring the real-time binding events. A 28-well plate biochip was built on a glass substrate by sequential deposition, patterning, and etching steps to create a stack nanowell array sensor with an electrode gap of 40 nm. Sensor response for cortisol concentrations between 1 and 15 μg/dl in buffer solution was recorded, and a limit of detection of 0.5 μg/dl was achieved. Last, 65 human serum samples were collected to compare the response from human serum samples with results from the standard enzyme-linked immunosorbent assay (ELISA). These results confirm that nanowell array sensors could be a promising platform for point-of-care testing, where real-time, laboratory-quality diagnostic results are essential.

Rapid and Sensitive Point of Care Detection of MRSA Genomic DNA by Nanoelectrokinetic Sensors

Biosensors have shown great potential in realizing rapid, low cost, and portable on-site detection for diseases. This work reports the development of a new bioelectronic sensor called AC electrokinetics-based capacitive (ABC) biosensor, for the detection of genomic DNA (gDNA) of methicillin-resistant Staphylococcus aureus (MRSA). The ABC sensor is based on interdigitated microelectrodes biofunctionalized with oligonucleotide probes. It uses a special AC signal for direct capacitive monitoring of topological change on nanostructured sensor surface, which simultaneously induces dielectrophoretic enrichment of target gDNAs. As a result, rapid and specific detection of gDNA/probe hybridization can be realized with high sensitivity. It requires no signal amplification such as labeling, hybridization chain reaction, or nucleic acid sequence-based amplification. This method involves only simple sample preparation. After optimization of nanostructured sensor surface and signal processing, the ABC sensor demonstrated fast turnaround of results (~10 s detection), excellent sensitivity (a detection limit of 4.7 DNA copies/µL MRSA gDNA), and high specificity, suitable for point of care diagnosis. As a bioelectronic sensor, the developed ABC sensors can be easily adapted for detections of other infectious agents.

Label-free highly sensitive detection of DNA approximate length and concentration by impedimetric CRISPR-dCas9 based biosensor technology

In this study, we designed a CRISPR-dCas9-based biosensor with potential clinical use in glioblastoma subtype discrimination through detection of isocitrate dehydrogenase R132H (IDH) mutation status. The electrode was modified to detect mutant DNA cysteamine (Cys), PAMAM, dCas9 and sgRNA for R132H mutations, respectively. The biosensor system we proposed was able not only to detect mutant DNA, but also to measure the approximate length of DNA. Therefore, it can be considered that the biosensor technology that we developed is novel in the field of DNA biosensors. Another superior capability of the biosensor system is that it can simultaneously measure DNA concentration by electrochemical impedance spectroscopy and DNA length by capacitive detection, which lowers the concentration-based false-positive signals. The calibration range was obtained between 100 fM and 1000 fM, LOD and LOQ were also calculated as 33.96 fM and 102.91 fM respectively. Moreover, thanks to the sensitivity of the capacitive detection, the biosensor was able to discriminate the same EIS signals of the 200 bp and 250 fM concentration data and 1000 bp and 50 fM concentration data. In conclusion, the biosensor was capable of detect target DNA and DNA length, simultaneously in minutes.

An Approach to Ring Resonator Biosensing Assisted by Dielectrophoresis: Design, Simulation and Fabrication

The combination of extreme miniaturization with a high sensitivity and the potential to be integrated in an array form on a chip has made silicon-based photonic microring resonators a very attractive research topic. As biosensors are approaching the nanoscale, analyte mass transfer and bonding kinetics have been ascribed as crucial factors that limit their performance. One solution may be a system that applies dielectrophoretic forces, in addition to microfluidics, to overcome the diffusion limits of conventional biosensors. Dielectrophoresis, which involves the migration of polarized dielectric particles in a non-uniform alternating electric field, has previously been successfully applied to achieve a 1000-fold improved detection efficiency in nanopore sensing and may significantly increase the sensitivity in microring resonator biosensing. In the current work, we designed microring resonators with integrated electrodes next to the sensor surface that may be used to explore the effect of dielectrophoresis. The chip design, including two different electrode configurations, electric field gradient simulations, and the fabrication process flow of a dielectrohoresis-enhanced microring resonator-based sensor, is presented in this paper. Finite element method (FEM) simulations calculated for both electrode configurations revealed ∇E² values above 10¹⁷ V²m⁻³ around the sensing areas. This is comparable to electric field gradients previously reported for successful interactions with larger molecules, such as proteins and antibodies.

Electrical impedance as an indicator of microalgal cell health

Separating specific cell phenotypes from a heterotypic mixture is a critical step in many research projects. Traditional methods usually require a large sample volume and a complex preparation process that may alter cell property during the sorting process. Here we present the use of electrical impedance as an indicator of cell health and for identifying specific microalgal phenotypes. We developed a microfluidic platform for measuring electrical impedance at different frequencies using the bacterium-sized green alga Picochlorum SE3. The cells were cultured under different salinity conditions and sampled at four different time points. Our results demonstrate the utility of electrical impedance as an indicator of cell phenotype by providing results that are consistent with known changes in cell size and physiology. Outliers in the cell data distribution are particularly useful because they represent phenotypes that have the ability to maintain size and/or membrane ionic permeability under prolonged salt stress. This suggests that our device can be used to identify and sort desired (e.g., experimentally evolved, mutant) cell phenotypes based on their electrical impedance properties.

Rapid and Sensitive Detection of Bisphenol A Based on Self-Assembly

Bisphenol A (BPA) is an endocrine disruptor that may lead to reproductive disorder, heart disease, and diabetes. Infants and young children are likely to be vulnerable to the effects of BPA. At present, the detection methods of BPA are complicated to operate and require expensive instruments. Therefore, it is quite vital to develop a simple, rapid, and highly sensitive method to detect BPA in different samples. In this study, we have designed a rapid and highly sensitive biosensor based on an effective self-assembled monolayer (SAM) and alternating current (AC) electrokinetics capacitive sensing method, which successfully detected BPA at nanomolar levels with only one minute. The developed biosensor demonstrates a detection of BPA ranging from 0.028 μg/mL to 280 μg/mL with a limit of detection (LOD) down to 0.028 μg/mL in the samples. The developed biosensor exhibited great potential as a portable BPA biosensor, and further development of this biosensor may also be useful in the detection of other small biochemical molecules.

An interdigitated microelectrode based aptasensor for real-time and ultratrace detection of four organophosphorus pesticides

With increasing industrialization of food production, residues of organophosphorus pesticides (OPs) are more frequently found in the environment including rivers, lakes and soils. Extended exposure to OPs, even at a level below 1 nM, may lead to liver and central nervous system damages in humans and animals, while existing detection methods are not sensitive enough to detect OPs at trace levels. We presented a simple-to-use aptasensor to rapidly detect broad-spectrum OPs with high sensitivity. DNA aptamer was modified on the surface of a micro interdigitated electrode chip, and AC electrokinetics was employed to accelerate the binding of OP molecules to the aptamer probe. The sensing strategy directly measured the interfacial capacitance whose change rate was adopted as a quantitative indicator of recognition events, with a sample to result detection time of 30 s. This aptasensor had a wide linear range of (fM ~ nM), and the detection limit reached (0.24-1.67) fM for four highly-toxic OPs, with good specificity. It still showed good activity after being stored in non-refrigerated environment for at least 14 days. This aptasensor as well as the detection method offer a promising solution for on-site and real-time sensitive OP detection.

Interfacial capacitance immunosensing using interdigitated electrodes: the effect of insulation/immobilization chemistry

With the aim of improving the reproducibility of capacitive immunosensors, we performed a comparative study of four different insulating/immobilization chemistries.

An impedimetric bioaffinity sensing chip integrated with the long-range DC-biased AC electrokinetic centripetal vortex produced in a high conductivity solution

Immunoreaction of specific antibodies to antigens is widely used in numerous immunoanalysis applications. However, diffusion-dominated transport in stationary solutions limits the rate and binding density of immunoreaction. This research describes the construction of chip-type concentric multi-double ring electrodes and single central disk electrode. A +1 V-biased 6 V_pp voltage was applied to the multi-double ring electrodes to induce a long-range DC-biased AC electrokinetic flow (ACEKF). The immunoreaction was quantified by electrochemical impedance spectrum (EIS). Fluorescence-labeled secondary antibody (FLSA) and protein A were exemplified as an immunoreacting model to demonstrate the effect of ACEKF on immunoreaction efficiency. The results showed that FLSA binding can reach a plateau in 8 min with the DC-biased ACEKF vortex, and the increment of electron transfer resistance is 2.26 times larger than that obtained in the unstirred solution. The sensitivity of the calibration curves obtained by EIS detection with the aid of DC-biased ACEKF vortex is 1.51 times larger than that obtained in an unstirred solution. The label-free EIS-based sensing chip integrated with the long-range DC-biased ACEKF vortex promises to facilitate immunoreaction efficiency, which is beneficial for the development of a miniature and fast-detection in vitro diagnostic device.

Ultrasensitive interdigitated capacitance immunosensor using gold nanoparticles

Immunosensors based on interdigitated electrodes (IDEs), have recently demonstrated significant improvements in the sensitivity of capacitance detection. Herein, a novel type of highly sensitive, compact and portable immunosensor based on a gold interdigital capacitor has been designed and developed for the rapid detection of hepatitis B surface antigen (HBsAg). To improve the efficiency of antibody immobilization and time-saving, a self-assembled monolayer (SAM) of 2-mercaptoethylamine film was coated on IDEs. Afterwards, carboxyl groups on primary antibodies were activated through 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide and were immobilized on amino-terminated SAM for better control of the oriented immobilization of antibodies on gold IDEs. In addition, gold nanoparticles conjugated with a secondary antibody were used to enhance the sensitivity. Under optimal conditions, the immunosensor exhibited the sensitivity of 0.22 nF.pg ml^-1, the linear range from 5 pg ml^-1 to 1 ng ml^-1 and the detection limit of 1.34 pg ml^-1, at a signal-to-noise ratio of 3.

Rapid, highly sensitive detection of Gram-negative bacteria with lipopolysaccharide based disposable aptasensor

Gram-negative bacteria are one of the most common microorganisms in the environment. Their differential detection and recognition from Gram-positive bacteria has been attracting much attention over the years. Using Escherichia coli (E. coli) as a model, we demonstrated on-site detection of Gram-negative bacteria by an AC electrokinetics-based capacitive sensing method using commercial microelectrodes functionalized with an aptamer specific to lipopolysaccharides. Dielectrophoresis effect was utilized to enrich viable bacteria to the microelectrodes rapidly, achieving a detection limit of 10² cells/mL within a 30 s' response time. The sensor showed a negligible response to Staphylococcus aureus (S. aureus), a Gram-positive species. The developed sensor showed significant advantages in sensitivity, selectivity, cost, operation simplicity, and response time. Therefore, this sensing method has shown great application potential for environmental monitoring, food safety, and real-time diagnosis.

Gold nanoparticle-decorated reduced-graphene oxide targeting anti hepatitis B virus core antigen

Hepatitis B virus core antigen (HBcAg) is the major structural protein of hepatitis B virus (HBV). The presence of anti-HBcAg antibody in a blood serum indicates that a person has been exposed to HBV. This study demonstrated that the immobilization of HBcAg onto the gold nanoparticles-decorated reduced graphene oxide (rGO-en-AuNPs) nanocomposite could be used as an antigen-functionalized surface to sense the presence of anti-HBcAg. The modified rGO-en-AuNPs/HBcAg was then allowed to undergo impedimetric detection of anti-HBcAg with anti-estradiol antibody and bovine serum albumin as the interferences. Upon successful detection of anti-HBcAg in spiked buffer samples, impedimetric detection of the antibody was then further carried out in spiked human serum samples. The electrochemical response showed a linear relationship between electron transfer resistance and the concentration of anti-HBcAg ranging from 3.91ngmL^-1 to 125.00ngmL^-1 with lowest limit of detection (LOD) of 3.80ngmL^-1 at 3σm^-1. This established method exhibits potential as a fast and convenient way to detect anti-HBcAg.

Aptamer-functionalized capacitance sensors for real-time monitoring of bacterial growth and antibiotic susceptibility

To prevent spread of infection and antibiotic resistance, fast and accurate diagnosis of bacterial infection and subsequent administration of antimicrobial agents are important. However, conventional methods for bacterial detection and antibiotic susceptibility testing (AST) require more than two days, leading to delays that have contributed to an increase in antibiotic-resistant bacteria. Here, we report an aptamer-functionalized capacitance sensor array that can monitor bacterial growth and antibiotic susceptibility in real-time. While E. coli and S. aureus were cultured, the capacitance increased over time, and apparent bacterial growth curves were observed even when 10 CFU/mL bacteria was inoculated. Furthermore, because of the selectivity of aptamers, bacteria could be identified within 1h using the capacitance sensor array functionalized with aptamers. In addition to bacterial growth, antibiotic susceptibility could be monitored in real-time. When bacteria were treated with antibiotics above the minimum inhibitory concentration (MIC), the capacitance decreased because the bacterial growth was inhibited. These results demonstrate that the aptamer-functionalized capacitance sensor array might be applied for rapid ASTs.

A novel micromixer based on the alternating current-flow field effect transistor

Induced-charge electroosmosis (ICEO) phenomena have been attracting considerable attention as a means for pumping and mixing in microfluidic systems with the advantage of simple structures and low-energy consumption. We propose the first effort to exploit a fixed-potential ICEO flow around a floating electrode for microfluidic mixing. In analogy with the field effect transistor (FET) in microelectronics, the floating electrode act as a "gate" electrode for generating asymmetric ICEO flow and thus the device is called an AC-flow FET (AC-FFET). We take advantage of a tandem electrode configuration containing two biased center metal strips arranged in sequence at the bottom of the channel to generate asymmetric vortexes. The current device is manufactured on low-cost glass substrates via an easy and reliable process. Mixing experiments were conducted in the proposed device and the comparison between simulation and experimental results was also carried out, which indicates that the micromixer permits an efficient mixing effect. The mixing performance can be further enhanced by the application of a suitable phase difference between the driving electrode and the gate electrode or a square wave signal. Finally, we performed a critical analysis of the proposed micromixer in comparison with different mixer designs using a comparative mixing index (CMI). The novel methods put forward here offer a simple solution to mixing issues in microfluidic systems.

Rapid and sensitive detection of bisphenol a from serum matrix

Bisphenol A (BPA) is an endocrine disrupting compound that may have adverse developmental, reproductive, neurological, and immune system effects. Low-level exposure to BPA is ubiquitous in human populations due to its widespread use in consumer products. Therefore, highly sensitive methods are needed to quantify BPA in various matrices including water, serum, and food products. In this study, we developed a simple, rapid, highly sensitive and specific sensor based on an aptamer probe and AC electrokinetics capacitive sensing method that successfully detected BPA at femto molar (fM) levels, which is an improvement over prior work by a factor of 10. We were able to detect BPA spiked in human serum as well as in maternal and cord blood within 30s. The sensor is responsive to BPA down to femto molar levels, but not to structurally similar compounds including bisphenol F (BPF) or bisphenol S (BPS) even at much higher concentration. Further development of this platform may prove useful in monitoring exposure to BPA and other small molecules in various matrices.

A highly sensitive and specific capacitive aptasensor for rapid and label-free trace analysis of Bisphenol A (BPA) in canned foods

A rapid, highly sensitive, specific and low-cost capacitive affinity biosensor is presented here for label-free and single step detection of Bisphenol A (BPA). The sensor design allows rapid prototyping at low-cost using printed circuit board material by benchtop equipment. High sensitivity detection is achieved through the use of a BPA-specific aptamer as probe molecule and large electrodes to enhance AC-electroelectrothermal effect for long-range transport of BPA molecules toward electrode surface. Capacitive sensing technique is used to determine the bounded BPA level by measuring the sample/electrode interfacial capacitance of the sensor. The developed biosensor can detect BPA level in 20s and exhibits a large linear range from 1 fM to 10 pM, with a limit of detection (LOD) of 152.93 aM. This biosensor was applied to test BPA in canned food samples and could successfully recover the levels of spiked BPA. This sensor technology is demonstrated to be highly promising and reliable for rapid, sensitive and on-site monitoring of BPA in food samples.

Compact Nanowire Sensors Probe Microdroplets

The conjunction of miniature nanosensors and droplet-based microfluidic systems conceptually opens a new route toward sensitive, optics-less analysis of biochemical processes with high throughput, where a single device can be employed for probing of thousands of independent reactors. Here we combine droplet microfluidics with the compact silicon nanowire based field effect transistor (SiNW FET) for in-flow electrical detection of aqueous droplets one by one. We chemically probe the content of numerous (∼10(4)) droplets as independent events and resolve the pH values and ionic strengths of the encapsulated solution, resulting in a change of the source-drain current ISD through the nanowires. Further, we discuss the specificities of emulsion sensing using ion sensitive FETs and study the effect of droplet sizes with respect to the sensor area, as well as its role on the ability to sense the interior of the aqueous reservoir. Finally, we demonstrate the capability of the novel droplets based nanowire platform for bioassay applications and carry out a glucose oxidase (GOx) enzymatic test for glucose detection, providing also the reference readout with an integrated parallel optical detector.

Bisphenol A Sensors on Polyimide Fabricated by Laser Direct Writing for Onsite River Water Monitoring at Attomolar Concentration

This work presents an aptamer-based, highly sensitive and specific sensor for atto- to femtomolar level detection of bisphenol A (BPA). Because of its widespread use in numerous products, BPA enters surface water from effluent discharges during its manufacture, use, and from waste landfill sites throughout the world. On-site measurement of BPA concentrations in water is important for evaluating compliance with water quality standards or environmental risk levels of the harmful compound in the environment. The sensor in this work is porous, conducting, interdigitated electrodes that are formed by laser-induced carbonization of flexible polyimide sheets. BPA-specific aptamer is immobilized on the electrodes as the probe, and its binding with BPA at the electrode surface is detected by capacitive sensing. The binding process is aided by ac electroosmotic effect that accelerates the transport of BPA molecules to the nanoporous graphene-like structured electrodes. The sensor achieved a limit of detection of 58.28 aM with a response time of 20 s. The sensor is further applied for recovery analysis of BPA spiked in surface water. This work provides an affordable platform for highly sensitive, real time, and field-deployable BPA surveillance critical to the evaluation of the ecological impact of BPA exposure.

Single frequency analysis for clinical immunosensor design

A novel bioelectrochemical approach: Tau protein determination for the diagnosis of neurodiseases via time-dependant phase angle shift.

Molecular epidemiology, risk factors and hematochemical alterations induced by Theileria annulata in bovines of Punjab (India)

Bovine tropical theileriosis, caused by Theileria annulata, is one of the economically important fatal tick borne haemoprotozoan diseases of dairy animals. The aim of present investigation was to map the distribution of T. annulata in bovines of Punjab state of India in relation to various risk factors including age, sex of animals, location and management of farms. In a cross sectional study, a total of 1278 blood samples were randomly collected from twenty districts falling in five major agro-climatic zones of Punjab. All the samples were screened by blood smear examination followed by polymerase chain reaction targeting SSU rRNA gene for Theileria spp. PCR positive samples (n = 386) for Theileria spp. were then analyzed for T. annulata by amplification of Tams1 gene. Overall prevalence of T. annulata was found to be 29.26% in Punjab, with highest in western Zone (40.49%, 95% CI = 35.57-45.41) and lowest in submountain zone (18.90%, 95% CI = 13.73-24.06). The propensity of incidence of T. annulata was found to be highest in cross bred cattle (32.40%, 95% CI = 29.87-34.94), followed by indigenous cattle (19.64%, 95% CI = 10.67-28.61) and buffaloes (19.2%, 95% CI = 14.99-23.41). Between the two sexes, incidence of T. annulata was higher in female animals. Calves less than 6 months of age were found to be more prone to theileriosis.

Agent-based model for Johne's disease dynamics in a dairy herd

Johne’s disease is an infectious gastrointestinal disease in ruminants caused by Mycobacterium avium subsp. paratuberculosis that causes diarrhea, emaciation, decreased milk production and eventually death. The disease is transmitted in utero and via milk and colostrums to calves, and fecal-orally to all age classes. Financial losses due to the disease are estimated to be over $200 million in the US dairy industry. The goal of this study was to evaluate the cost effectiveness of control measures based on diagnosis with a sensitive ELISA, EVELISA. An agent-based, discrete time model was developed to simulate Johne’s disease dynamics in a US dairy herd. Spatial aspects of disease transmission were taken into account by using six spatial compartments. The effects on disease prevalence were studied with and without transmission routes included in the model. Further, using the model, cost effectiveness of ELISA-based Johne’s disease control was evaluated. Using the parameters we collected and assumed, our model showed the initial prevalence of Johne’s disease (33.1 ± 0.2%) in the farm increased to 87.7 ± 1.7% in a 10 year-simulation. When ELISA-based control measures were included in the simulation, the increase in prevalence was significantly slowed down, especially when EVELISA was used. However, the level of the prevalence was still higher than the initial level after 10 year simulation even with the ELISA-based diagnostic intervention. The prevalence was further reduced when quarterly ELISA testing was included. The cost analysis showed that the quarterly ELISA and EVELISA testing could bring $44.8 and $51.5/animal/year more revenues, respectively, to a dairy farm.