Physicochemical characterization of cellulose from perennial ryegrass leaves (Lolium perenne)

Exploring Spent Coffee Grounds: Comprehensive Morphological Analysis and Chemical Characterization for Potential Uses

The agroindustry generates substantial quantities of byproducts, particularly in coffee production, which yields significant waste, most notably spent coffee grounds (SCGs). This study explores the potential of SCGs as a versatile resource for applications in both food and nonfood sectors. A comprehensive chemical analysis revealed that SCGs consist of 30.2 wt.% cellulose, 25 wt.% hemicellulose, and 12 wt.% lignin. Morphological characterization was performed using field emission scanning electron microscopy (FESEM). Additional analyses included attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) and thermogravimetric analysis (TGA). ATR-FTIR identified key polysaccharides and oils, whereas TGA offered insights into the thermal degradation behavior of SCGs, confirming the presence of typical plant cell wall components. X-ray diffraction (XRD) patterns revealed low crystallinity, consistent with SCGs' amorphous structure. Mineral content was assessed using inductively coupled plasma atomic emission spectrometry (ICP-AES) and atomic absorption spectrophotometry (AAS). The results showed that mineral concentrations in SCGs (per 0.01 kg) were within recommended daily intake limits, confirming their safety for potential human consumption. These findings establish SCGs as a valuable lignocellulosic biomass with applications in composite materials. Additionally, it can serve as an organic soil amendment after fermentation to prevent stress on plants. This approach supports effective waste management and advances resource sustainability practices in the agro-industrial sector.

Are Microfibers a Threat to Marine Invertebrates? A Sea Urchin Toxicity Assessment

The rise of "fast fashion" has driven up the production of low-cost, short-lived clothing, significantly increasing global textile fiber production and, consequently, exacerbating environmental pollution. This study investigated the ecotoxicological effects of different types of anthropogenic microfibers-cotton, polyester, and mixed fibers (50% cotton: 50% polyester)-on marine organisms, specifically sea urchin embryos. All tested fibers exhibited toxicity, with cotton fibers causing notable effects on embryonic development even at environmentally relevant concentrations. The research also simulated a scenario where microfibers were immersed in seawater for 30 days to assess changes in toxicity over time. The results showed that the toxicity of microfibers increased with both concentration and exposure duration, with polyester being the most toxic among the fibers tested. Although synthetic fibers have been the primary focus of previous research, this study highlights that natural fibers like cotton, which are often overlooked, can also be toxic due to the presence of harmful additives. These natural fibers, despite decomposing faster than synthetic ones, can persist in aquatic environments for extended periods. The findings underline the critical need for further research on both natural and synthetic microfibers to understand their environmental impact and potential threats to marine ecosystems and sea urchin populations.

Recovery and characterization of cellulose microfibers from fallen leaves and evaluation of their potential as reinforcement agents for production of new biodegradable packaging materials

In the present work, cellulose microfibers (CMFs) isolated from fallen autumn leaves of cherry plum (Prunus cerasifera pissardii nigra), white mulberry (Morus alba) and plane (Platanus orientalis) trees were characterized and used as reinforcement agents in sodium alginate-based biodegradable films. Fourier transform infrared spectroscopy (FT-IR) characterization showed that the CMFs were successfully isolated from the leaves with high purity. The extracted CMFs had a particle size ranging from 321.20 nm to 632.26 nm and negative zeta potential values (-27.33 to -21.40). The extraction yield of CMFs ranged from 19.53% to 26.00%. Incorporation of the leaf-derived CMFs into sodium alginate based films (1%, w:w) increased their tensile strength (from 153.73 to 187.78 MPa) and elongation at break values (from 105.97% to 89.90%) and significantly decreased oxygen (from 121.46 to 75.56 meq kg-1) and water vapor permeabilities (from 2.36 to 1.60 g mm h-1 m-2 kPa-1)(p < 0.05). Furthermore, the supplementation of CMFs into the biopolymer matrix had no significant effect on the color (L*: 85.35-85.67; a*: -0.75-0.71; b*: 4.23-4.94) and moisture content (44.64-48.42%) of the film samples, although the thickness increased (40.33-94.66 μm). Scanning electron microscopy (SEM) images showed that CMFs were homogeneously dispersed in the film matrix. Overall, this study confirms that fallen cherry plum, white mulberry, and plane leaves are valuable sources of CMFs which could be used in the manufacturing of biodegradable nanocomposite films as reinforcement agents.

Enhancing Insight into Photochemical Weathering of Flax and Miscanthus: Exploring Diverse Chemical Compositions and Composite Materials

The accelerated weathering of flax and miscanthus fibers possessing distinct chemical compositions was investigated. The chosen fibers included raw, extractive-free (EF) and delignified samples (x3), alone and used as fillers in a stabilized polypropylene blue matrix (PP). Modifications in both color and the chemical composition of the fibers throughout the weathering process under ultraviolet (UV) light were meticulously tracked and analyzed by spectrophotometry and attenuated total reflectance with Fourier-transform infrared spectroscopy (ATR-FTIR). The inherent nature and composition of the selected fibers led to varied color-change tendencies. Raw and EF flax fibers exhibited lightening effects, while raw and EF miscanthus fibers demonstrated darkening effects. Extractives exhibited negligible influence on the color alteration of both flax and miscanthus fibers. This disparity between the fibers correlates with their respective lignin content and type, and the significant formation of carbonyl (C=O) groups in miscanthus. Better stability was noted for delignified flax fibers. A comparative study was achieved by weathering the PP matrix containing these various fibers. Contrary to the weathering observations on individual fibers, it was noted that composites containing raw and EF flax fibers exhibited significant color degradation. The other fiber-containing formulations showed enhanced color stability when compared to the pure PP matrix. The study highlights that the UV stability of composites depends on their thermal history. As confirmed by thermogravimetric analysis (TGA), fiber degradation during extrusion may affect UV stability, a factor that is not apparent when fibers alone are subjected to UV aging.

Affinity of Tannins to Cellulose: A Chromatographic Tool for Revealing Structure-Activity Patterns

Food, feed and beverage processing brings tannins into contact with macromolecules, such as proteins and polysaccharides, leading to different chemical and physical interactions. The interactions of tannins with proteins are well known but less is known about the affinity of tannins to polysaccharides. We used bacterial cellulose from nata de coco as a model compound to investigate how tannins and cellulose interact by adsorption measurements using UPLC-DAD. We also explored how the structure of tannins influences these interactions. The model tannins included nine individual structurally different hydrolysable tannins (HTs) and eight well-defined proanthocyanidin (PA) fractions with different monomeric units, mean degree of polymerization and both A- and B-type linkages. Tannins were found to have both strong and weak interactions with bacterial cellulose, depending on the exact structure of the tannin. For HTs, the main structural features affecting the interactions were the structural flexibility of the HT molecule and the number of free galloyl groups. For PAs, prodelphinidins were found to have a higher affinity to cellulose than procyanidins. Similarly to HTs, the presence of free galloyl groups in galloylated PAs and the flexibility of the PA molecule led to a stronger interaction. Adsorption measurements by UPLC-DAD proved to be a sensitive and rapid tool to evaluate the affinity of tannins to cellulose.

Synergistic effect of microcrystalline cellulose from oil palm empty fruit bunch waste and tricresyl phosphate on the properties of polylactide composites

Microcrystalline cellulose (MCC) was extracted from oil palm empty fruit bunch (OPEFB) waste by integrated chemical treatments of delignification, bleaching, and acidic hydrolysis. The obtained MCC (OPMC) and tricresyl phosphate (TCP) were used as additives for polylactide (PLA) composites. The influences of OPMC and TCP contents, separately and in combination, were evaluated on the properties of the composites. Characterization studies confirmed the successful extraction of OPMC from OPEFB waste. With regard to the properties of the PLA composite, the appropriate content of OPMC should be 5 phr. The good distribution of OPMC in the polymer matrix changed the failure behavior of the composite from brittle to ductile. All the PLA composites with TCP and OPMC showed flame inhibition and retarded ignition. The synergistic effect of TCP and OPMC resulted in outstanding improvement of impact strength and flame retardancy of composites. The impact toughness of PT10M5 increased to about 218.4 % and 72.3 % that of neat PLA and PT0M5, respectively. Moreover, PT10M5 achieved V-0 rating with high LOI (38.5 %). All these characteristics promise extended applications for PLA composite in bio, circular, and green (BCG) economies and electronics industries.

Fabrication and Characterization of Degradable Crop-Straw-Fiber Composite Film Using In Situ Polymerization with Melamine-Urea-Formaldehyde Prepolymer for Agricultural Film Mulching

Soil mulch composite films composed of biodegradable materials are being increasingly used in agriculture. In this study, mulch films based on wheat straw fiber and an environmentally friendly modifier were prepared via in situ polymerization and tested as the ridge mulch for crops. The mechanical properties of the straw fiber film were significantly enhanced by the modification. In particular, the films exhibited a noticeable increase in dry and wet tensile strength from 2.35 to 4.15 and 0.41 to 1.51 kN/m, respectively, with increasing filler content from 0% to 25%. The contact angle of the straw also showed an improvement based on its hydrophilicity. The crystallinity of the modified film was higher than that of the unmodified film and increased with modifier content. The changes in chemical interaction of the straw fiber film were determined by Fourier transform infrared spectroscopy, and the thermal stability of the unmodified film was improved by in situ polymerization. Scanning electron microscopy images indicated that the modifier was uniformly dispersed in the fiber film, resulting in an improvement in its mechanical properties. The modified straw fiber films could be degraded after mulching for approximately 50 days. Overall, the superior properties of the modified straw fiber film lend it great potential for agricultural application.

Synergistic effect of pistachio shell powder and nano-zerovalent copper for chromium remediation from aqueous solution

Pistachio shell powder supported nano-zerovalent copper (ZVC@PS) material prepared by borohydride reduction was characterized using SEM, FTIR, XRD, TGA/DTA, BET, and XPS. SEM, XRD, and XPS revealed the nano-zerovalent copper to consist of a core-shell structure with CuO shell and Cu(0) core with a particle size of 40-100 nm and spherical morphology aggregated on PS biomass. ZVC@PS was found to contain 39% (w/w %) Cu onto the pistachio shell biomass. Batch sorption of Cr(VI) from the aqueous using ZVC@PS was studied and was optimized for dose (0.1-0.5 g/L), initial Cr(VI) concentration(1-20 mg/L), and pH (2-12). Optimized conditions were 0.1 g/L doses of sorbent and pH=3 for Cr(VI) adsorption. Langmuir and Freundlich adsorption isotherm models fitted well to the adsorption behavior of ZVC@PS for Cr(VI) with a pseudo-second-order kinetic behavior. ZVC@PS (0.1g/L) exhibits q_max for Cr(VI) removal up to 110.9 mg/g. XPS and other spectroscopic evidence suggest the adsorption of Cr(VI) by pistachio shell powder, coupled with reductive conversion of Cr(VI) to Cr(III) by ZVC particles to produce a synergistic effect for the efficient remediation of Cr(VI) from aqueous medium.

Development of co-culture yeast fermentation for efficient production of biobutanol from rice straw: A useful insight in valorization of agro industrial residues

Escalating environmental concerns and petroleum demands leads into the present study. In this investigation delignification of rice straw was optimized by NaOH and H2SO4 pretreatment using L16 Taguchi orthogonal array. NaOH pretreatment revealed higher delignification as compared to H₂SO₄ and; further subjected to separate enzymatic hydrolysis and co-fermentation (SHCF) using RSM as the SHCF demonstrated a maximum glucose and xylose yield of 575 and 205 mg/g. Further, butanol concentration of 4.32 g/L was achieved from 20 g/L of sugar loadings by co-culture of Saccharomyces cerevisiae and Pichia sp. at 72 h of incubation time which was 79.25% higher as compared to monocultures of Pichia sp. Scale-up experiments with higher sugar loadings (90 g/L) demonstrated a butanol concentration of 13.3 g/L. The release of amino acids in co-culture and monoculture systems demonstrated that the addition of S. cerevisiae promoted the butanol synthesis pathway which led to higher butanol concentration.

Plant celluloses, hemicelluloses, lignins, and volatile oils for the synthesis of nanoparticles and nanostructured materials

A huge variety of plants are harvested worldwide and their different constituents can be converted into a broad range of bionanomaterials. In parallel, much research effort in materials science and engineering is focused on the formation of nanoparticles and nanostructured materials originating from agricultural residues. Cellulose (40-50%), hemicellulose (20-40%), and lignin (20-30%) represent major plant ingredients and many techniques have been described that separate the main plant components for the synthesis of nanocelluloses, nano-hemicelluloses, and nanolignins with divergent and controllable properties. The minor components, such as essential oils, could also be used to produce non-toxic metal and metal oxide nanoparticles with high bioavailability, biocompatibility, and/or bioactivity. This review describes the chemical structure, the physical and chemical properties of plant cell constituents, different techniques for the synthesis of nanocelluloses, nanohemicelluloses, and nanolignins from various lignocellulose sources and agricultural residues, and the extraction of volatile oils from plants as well as their use in metal and metal oxide nanoparticle production and emulsion preparation. Furthermore, details about the formation of activated carbon nanomaterials by thermal treatment of lignocellulose materials, a few examples of mineral extraction from agriculture waste for nanoparticle fabrication, and the emerging applications of plant-based nanomaterials in different fields, such as biotechnology and medicine, environment protection, environmental remediation, or energy production and storage, are also included. This review also briefly discusses the recent developments and challenges of obtaining nanomaterials from plant residues, and the issues surrounding toxicity and regulation.

Improvement of the Weather Resistance of a Selective Laser-Sintered Copolyester-Limestone Composite Using UV-326 and UV-328

A copolyester-limestone composite fabricated with selective laser sintering technology is a potential material for the repair of ancient brick structures damaged by the sun and rain, however the weather resistance of this material must be improved. Herein, UV-236 and UV-328 were employed as UV stabilizers and added into the composite. The results show that the addition of UV-326 and UV-328 effectively inhibited the degradation of CH and ester groups and the formation of hydroxyl, carbonyl, and carboxyl groups. Thus, the stabilizers significantly reduced the color change and decline in mechanical properties of the composite under sun and rain conditions. The proposed strategy can be used for the repair of damaged precious brick buildings.

Observation of Potential Contaminants in Processed Biomass Using Fourier Transform Infrared Spectroscopy

With rapidly increased interests in biomass, diverse chemical and biological processes have been applied for biomass utilization. Fourier transform infrared (FTIR) analysis has been used for characterizing different types of biomass and their products, including natural and processed biomass. During biomass treatments, some solvents and/or catalysts can be retained and contaminate biomass. In addition, contaminants can be generated by the decomposition of biomass components. Herein, we report FTIR analyses of a series of contaminants, such as various solvents, chemicals, enzymes, and possibly formed degradation by-products in the biomass conversion process along with poplar biomass. This information helps to prevent misunderstanding the FTIR analysis results of the processed biomass.

Enhancing the Enzymatic Saccharification of Grain Stillage by Combining Microwave-Assisted Hydrothermal Irradiation and Fungal Pretreatment

Grain stillage from the liquor industry was pretreated by using microwave-assisted hydrothermal pretreatment, fungal pretreatments, and their combination to enable efficient enzymatic hydrolysis for sugar production. The microwave-assisted hydrothermal (MH) pretreatment was optimized by using a response surface methodology, and the respective maximum reducing sugar yield and saccharification efficiency of 17.59 g/100 g and 33.85%, respectively, were achieved under the pretreatment conditions of microwave power = 120 W, solid-to-liquid ratio = 1:15 (g·mL^-1), and time = 3.5 min. The fungal pretreatment with Phanerochaete chrysosporium digestion (PC) achieved the maximum ligninolytic enzyme activities in 6 days with 10% inoculum size at which the reducing sugar yield and saccharification efficiency reached 19.74 g/100 g and 36.29%, respectively. To further improve the pretreatment efficiency, MH and PC pretreatments were combined, but the sequence of MH and PC mattered on the saccharification efficiency. The MH + PC pretreatment (the MH prior to the PC) was better than PC + MH (the PC prior to the MH) in terms of saccharification efficiency. Overall, the MH + PC pretreatment achieved superior reducing sugar yield and saccharification efficiency (25.51 g/100 g and 66.28%, respectively) over all other studied pretreatment methods. The variations of chemical compositions and structure features of the raw and pretreated grain stillage were characterized by using scanning electron microscopy and Fourier transform infrared spectroscopy. The results reveal that both MH and PC pretreatments mainly functioned on delignification and decreasing cellulose crystallinity, thus enhancing the enzymatic saccharification of the pretreated grain stillage. The combined MH and PC pretreatment could be a promising method to enable cost-efficient grain stillage utilization for downstream applications such as biofuels.

Micrometer Copper-Zinc Alloy Particles-Reinforced Wood Plastic Composites with High Gloss and Antibacterial Properties for 3D Printing

In this work, micrometer copper-zinc alloy particles-reinforced particleboard wood flour/poly (lactic acid) (mCu-Zn/PWF/PLA) wood plastic composites with high gloss and antibacterial properties for 3D printing were prepared by a melt blending process. The structure and properties of the composites with different contents of mCu-Zn were analyzed by means of mechanical testing, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, X-ray diffraction, scanning electron microscopy, and antibacterial testing. The results showed that the mechanical properties, thermal stability, and antibacterial performance of the composites were significantly improved, as mCu-Zn was added into the wood plastic composites. When adding 2 wt.% mCu-Zn, the flexural strength of mCu-Zn/PWF/PLA composites (with 5 wt.% of particleboard wood flour) (PWF) increased by 47.1% compared with pure poly (lactic acid) (PLA), and 18.9% compared with PWF/PLA wood plastic composites. The surface gloss was increased by 1142.6% compared with PWF/PLA wood plastic composites. Furthermore, the inhibition rates of mCu-Zn/PWF/PLA composites against Escherichia coli reached 90.43%. Therefore, this novel high gloss and antibacterial wood plastic composites for fused deposition modeling (FDM) 3D printing have potential applications in personalized and classic furniture, art, toys, etc.

Enhanced phosphate removal using zirconium hydroxide encapsulated in quaternized cellulose

Zirconium-based materials are efficient adsorbent for aqueous phosphate removal. However, current zirconium-based materials still show unsatisfied performance on adsorption capacity and selectivity. Here, we demonstrate a zirconium hydroxide encapsulated in quaternized cellulose (QC-Zr) for the selective phosphate removal. Zirconium hydroxide nanoparticles were simultaneously generated in situ with the QC framework and firmly anchored in the three-dimensional (3D) cross-linked cellulose chains. The maximum P adsorption capacity of QC-Zr was 83.6 mg P/g. Furthermore, the QC-Zr shows high P adsorption performance in a wide pH range, generally due to the electrostatic effects of quaternized cellulose. The enhanced adsorption of P was also achieved in the presence of competing anions (including Cl^-, NO₃^-, SO₄^2-, SO₄^4-) and humic acid (HA) even at a molar ratio up to 20 levels. The column adsorption capacity of QC-Zr reached 4000 bed volumes (BV) at EBCT = 0.5 min as the P concentration decreased from 2.5 to 0.5 mg/L. Mechanism study revealed that both -N⁺(CH₃)₃ groups and zirconium hydroxide were involved in phosphate adsorption via electrostatic interactions between -N⁺(CH₃)₃ and phosphate, and the formation of zirconium hydrogen phosphate (Zr(HPO₄)x). The ³¹P nuclear magnetic resonance (NMR) study implied that P surface-precipitated and inner-sphere complexed with zirconium hydroxide at a ratio of 3:1.

Selective and efficient sequestration of phosphate from waters using reusable nano-Zr(IV) oxide impregnated agricultural residue anion exchanger

There is an urgent need to develop low-cost and effective adsorbents for enhanced removal of phosphate from contaminated waters. In this study, nanosized Zr(IV) oxide particles were immobilized on the amino modified corn staw (MCS) to fabricate a novel nanocomposite (Zr@MCS) with superior application capability. Compared with the widely used commercial anion exchangers in previous studies, the modified agricultural residue was empolyed as the host to avoid the high costs and secondary pollution in the preparation. Zr@MCS displayed remarkable selective removal of phosphate from water even in the presence of coexisting anions (Cl^-, SO₄^2-, NO₃^-) at high levels, as well as with a high adsorption capacity, fast adsorption kinetics and high availability in the wide range of pH 2-8 toward phosphate. The excellent adsorption performance of Zr@MCS is attributed to the synergistic effect of the electrostatic attraction of the quaternary ammonium groups fixed on the host skeleton and the specific adsorption of phosphate derived from the hydroxyl functional groups of Zr(IV) oxide. The exhausted Zr@MCS can be effectively regenerated by 5% NaOH-NaCl solution for sustainably utilized, and phosphorus in the desorption effluent could be recovered as high-quality struvite by a simple struvite recovery process. Furthermore, the considerable treatment volume for the synthetic solution and real wastewater in a fixed-bed flow system indicated that Zr@MCS is of great potential for phosphate removal in practice.

Immobilization of heavy metals in contaminated soils by modified hydrochar: Efficiency, risk assessment and potential mechanisms

The modified hydrochar was prepared by a facile one-pot lime-assisted hydrothermal synthesis approach and the modified hydrochar and pristine hydrochar were investigated to immobilize the heavy metals (HMs) of Pb and Cd in contaminated soils. The results showed that the modified hydrochar exerted significantly enhanced effectiveness in immobilizing Pb and Cd comparing to pristine hydrochar, resulting from the increased surface functionality and non-crystalline properties, increased pH value and enhanced electronegativity of hydrochar. By introduction with 5% modified hydrochar, the contaminated soils showed the highest value of 34.5% (Pb) and 8.1% (Cd) reductions in leaching toxicity, and significant improvements of 95.1% (Pb) and 64.4% (Cd) were observed. In addition, the concentrations of acid soluble fraction were remarkably reduced by 54.0% (Pb) and 27.0% (Cd), and the reductions were much higher than that of 29.5% (Pb) and 8.3% (Cd) for 5% pristine hydrochar treatment. The enhanced surface complexation, precipitation and cation-π interaction played an important role in the immobilization of HMs in soils. The present study offered a novel and cost-effective approach to prepare soil amendment from waste biomass towards HMs immobilization in contaminated soils.

Textile Wastewater Purification Using an Elaborated Biosorbent Hybrid Material (Luffa–Cylindrica–Zinc Oxide) Assisted by Alternating Current

This paper aims to synthesize hybrid materials with high pollutant-uptake capacity and low costbased based on Luffa cylindrica (L.C) and different percentage of Zn2+ in the presence and absence of alternating current (AC). Physico-chemical, morphological and structural characterizations of the hybrid materials were performed by Boehm method, point zero charge (pHpzc), infrared characterizations (IR), scanning electron microscopy (SEM), energy–dispersive spectroscopyand and X-ray photoelectron spectroscopy. The efficiency of the designed hybrid materials was optimized based on their performance in water depollution. Methylene blue (MB) and industrial textile wastewater were the investigated pollutants models. IR characterizations confirmed the fixation of Zn2+ onto the L.C by the creation of Zn-OH, Zn-O and Zn-O-C bonds. Boehm titration showed that the fixation of Zn2+ onto L.C is accompanied by an increase of the basic functions of its surface and subsequently an increase in the pHpzc. SEM results confirmed the fixation of Zn2+ onto the L.C coupling AC with biosorption showed an increase in the adsorbed amount of MB and speed when adding the 4% of Zn2+ compared to the pure L.C the Qm shifted from 3.22 to 9.84 and 8.81 mg/g, respectively, for hybrid materials synthesized under AC, in absence of AC and pure L.C.

The combination of Luffa cylindrical fibers and metal oxides offers a highly performing hybrid fiber material in water decontamination

The present investigation aims to prepare a hybrid material from Luffa cylindrica and metal oxides (ZnO, Al₂O₃) by precipitation for different percentages of zinc and aluminum (1, 2, and 4%) with a determined amount of biomass (a diameter of 250 μm). Physicochemical characterization of "Luffa cylindrica" and "Luffa cylindrica-metal oxides" was carried out by Boehm titration, pH_PZC determination, scanning electron microscopy (SEM), and FTIR spectroscopic analysis. The process was optimized according to the adsorbed amount of methylene blue: MB (cationic dye) and methyl orange: MO (anionic dye) onto Luffa cylindrica and hybrid materials prepared. The results demonstrated the efficiency of the designed hybrid materials in removing MB and MO, accelerating the biosorption process and improving the performance of Luffa cylindrica fibers. The highest quantities adsorbed of dyes were obtained by the hybrid material prepared using 4% ZnO. Finally, the Brouers-Sotolongo mathematical modeling of kinetics was used in order to describe the pollutants retention process.

A new and highly efficient conservation treatment for deacidification and strengthening of aging paper by in-situ quaternization

Ancient papers, facing the threat of acidification, aging and microbial corrosion, need to be repaired due to their significance of history, art and culture research. In this work, a new and highly efficient approach was proposed to deacidify and strengthen aging paper by in-situ quaternization for the conservation, in which MgO nanoparticles dispersed in hexamethyldisiloxane was coated on the paper surface and the aqueous alkaline solution and the 2, 3-epoxypropyl trimethyl ammonium chloride/isopropyl alcohol/water mixture were sprayed in a closed reactor. Results showed that properties of ageing papers were improved after MSCE-8/2 treatment. The pH value was in the range of 7.5-9.0 and the maximum amount of alkali storage was 220 mmol/Kg. The tensile strength and folding endurance were increased by 28.05% and 80%, respectively. The fluctuation range of brightness and chromatic aberration was 0.14 and 1.27. Moreover, treated paper also had the great anti-bacteria and anti-aging effects.

Prediction of Lignin Content in Ruminant Diets and Fecal Samples Using Rapid Analytical Techniques

The measurement of lignin content in ruminant diet and fecal samples is important for digestibility studies, but it is typically time-consuming and costly. The work reported involves correlation of traditional wet chemistry data with those from three rapid instrumental techniques, Fourier transform infrared spectroscopy (FTIR), conventional thermogravimteric analysis (TGA), and high-resolution TGA (MaxRes TGA) to predict the lignin content of diets and feces from digestibility trials. Calibration and performance data indicate that the FTIR model is acceptable for screening, while the conventional and MaxRes TGA predictions are high accuracy for quantitative analysis. Cross validation and model performance data reveal that MaxRes TGA provides the best-performing predictive model. This work shows that MaxRes TGA can accurately predict lignin content in ruminant diet and fecal samples with distinct advantages over traditional wet chemistry: namely, the requirement of small sample size, ease of sample preparation, speed of analysis, and high sample throughput at considerably lower cost.

Novel Biobased Textile Fiber from Colombian Agro-Industrial Waste Fiber

Fique fibers, native to Colombia, are traditionally used for ropes and bags. In the extraction of long fibers for these purposes, the same amount of short fibers is generated; the short fibers are then discarded in the soil or in landfills. This agro-industrial waste is cellulose-rich and can be potentially developed into new biobased products. As an alternative use for these fibers, viscose regenerated fibers with potential applications in the textile industry were developed. Fique waste fibers were pulped (to produce fique cellulose pulp, FCP) using a 3³ design of experiment (DOE) to adjust the variables of the whitening treatment, and DOE analysis showed that time and hydrogen peroxide concentration do not have a significant effect on non-cellulosic remotion, unlike temperature. The behavior of this pulp in the production of viscose was compared against that of commercially available wood cellulose pulp (WCP). FCP showed a suitable cellulose content with a high degree of polymerization, which makes it a viable pulp for producing discontinuous viscose rayon filaments. Both pulps showed the same performance in the production of the viscose dope and the same chemical, thermal, and mechanical behavior after being regenerated.

Evaluation of Cd(II) Ion Removal from Aqueous Solution by a Low-Cost Adsorbent Prepared from White Yam (Dioscorea rotundata) Waste Using Batch Sorption

An agricultural residue, white yam (Dioscorea rotundata) tuber peel (YTBS), was used for the removal of Cd(II) ion from an aqueous solution using a batch method. The adsorbent was characterized using FTIR, TGA, SEM, EDX, N2 BET, XRD, and XRF. The optimization of sorption variables such as pH, contact time, adsorbent dose, and initial metal ion concentration at 25 °C were also carried out. The results indicated the dependence of sorption on the adsorbate pH and adsorbent dose, while the adsorption system reached equilibrium in 180 min. The sorption kinetics was fitted to three models (pseudo first order, pseudo second order, and Elovich) to validate the kinetics, and the pseudo first order was the best model for the description of Cd(II) uptake. Equilibrium isotherm modelling was also carried out using the Langmuir, Freundlich, and Temkin models, with the Langmuir isotherm giving the best fitting to the experimental results. The maximum loading capacity (qmax) of the adsorbent for Cd(II) obtained from the Langmuir isotherm model was 22.4 mg∙g−1 with an isotherm constant (KL) of 3.46 × 10−3 L·mg−1 and r2 value of 0.99. This result indicates that the YTBS residue was a good adsorbent for the removal of Cd(II) ion from aqueous system.

Natural adsorbent based on sawdust for removing impurities in waste lubricants

Sawdust was expected to remove impurities in waste lubricant, and was modified with sodium hydroxide and triethanolamine, which can ameliorate its surface properties and improve its adsorption capacity. The increase of hydroxyl groups, the decrease of carbonyl groups and grafting new azyl after modification were beneficial for the adsorption of impurities. The surface area of modified sawdust is 0.969 m² g^-1, which is nearly 1.39 times as much as raw sawdust. The point of zero charge for modified sawdust decreased from 6.75 to 5.68 while the crystallinity of modified sawdust increased from 40.35 to 56.16. This research discovered that compared with raw sawdust and filter paper, modified sawdust possessed superior adsorption performances. The removal percentages for Si, Al, Fe, Cu was enhanced from 2.54%, 20.34%, 16.55%, 0.26% to 15.37%, 21.99%, 45.37%, 4.88%, respectively, while that for oxidation, aromatics, sulphation, soot and water was improved by 4.33, 4.69, 0.76, 1.20, 1.28 times at 80 °C with 1000 rpm for 12 h. The research has also explored the optimum adsorption conditions (adsorption temperature, adsorption time and rotation rate). The modified sawdust showed a stable adsorption capacity for impurities under different adsorption conditions.

From nano- to micrometer scale: the role of microwave-assisted acid and alkali pretreatments in the sugarcane biomass structure

BACKGROUND

To date, great strides have been made in elucidating the role of thermochemical pretreatments in the chemical and structural features of plant cell walls; however, there is no clear picture of the plant recalcitrance and its relationship to deconstruction. Previous studies precluded full answers due to the challenge of multiscale features of plant cell wall organization. Complementing the previous efforts, we undertook a systematic, multiscale, and integrated approach to track the effect of microwave-assisted H₂SO₄ and NaOH treatments on the hierarchical structure of plants, i.e., from a nano- to micrometer scale. We focused on the investigation of the highly recalcitrant sclerenchyma cell walls from sugarcane bagasse.

RESULTS

Through atomic force microscopy and X-ray diffraction analyses, remarkable details of the assembly of cellulose microfibrils not previously seen were revealed. Following the H₂SO₄ treatment, we observed that cellulose microfibrils were almost double the width of the alkali pretreated sample at the temperature of 160 °C. Such enlargement led to a greater contact between cellulose chains, with a subsequent molecule alignment, as indicated by the X-ray diffraction (XRD) results with the conspicuous expansion of the average crystallite size. The delignification process had little effect on the local nanometer-sized arrangement of cellulose molecules. However, the rigidity and parallel alignment of cellulose microfibrils were partially degraded. The XRD analysis also agrees with these findings as evidenced by large momentum transfer vectors (q > 20 nm^-1), interpreted as indicators of the long-range order of cell wall components, which were similar for all the studied samples except with application of the NaOH treatment at 160 °C. These changes were followed by the eventual swelling of the fiber cell walls.

CONCLUSIONS

Based on an integrated approach, we presented multidimensional architectural models of cell wall deconstruction resulting from microwave-assisted pretreatments. We provided direct evidence supporting the idea that hemicellulose is the main barrier for the swelling of cellulose microfibrils, whereas lignin adds rigidity to cell walls. Our findings shed light on the design of more efficient strategies, not only for the conversion of biomass to fuels but also for the production of nanocellulose, which has great potential for several applications such as composites, rheology modifiers, and pharmaceuticals.

A new method for recovery of cellulose from lignocellulosic bio-waste: Pile processing

This paper presents a new delignification method (pile processing) for the recovery of cellulose from lignocellulosic bio-wastes, adapted from heap leaching technology in metallurgy. The method is based on the stacking of cellulosic materials in a pile, irrigation of the pile with aqueous reactive solution from the top, lignin and hemicellulose removal and enrichment of cellulose by the reactive solution while percolation occurs through the bottom of the pile, recirculating the reactive solution after adjusting several values such as chemical concentrations, and allow the system run until the desired time or cellulose purity. Laboratory scale systems were designed using fall leaves (FL) as lignocellulosic waste materials. The ideal condition for FL was noted as: 0.1g solid NaOH addition per gram of FL into the irrigating solution resulting in instant increase in pH to about 13.8, later allowing self-decrease in pH due to delignification over time down to 13.0, at which point another solid NaOH addition was performed. The new method achieved enrichment of cellulose from 30% to 81% and removal of 84% of the lignin that prevents industrial application of lignocellulosic bio-waste using total of 0.3g NaOH and 4ml of water per gram of FL at environmental temperature and pressure. While the stirring reactions used instead of pile processing required the same amount of NaOH, they needed at least 12ml of water and delignification was only 56.1%. Due to its high delignification performance using common and odorless chemicals and simple equipment in mild conditions, the pile processing method has great promise for the industrial evaluation of lignocellulosic bio-waste.

Utilization of chemically treated municipal solid waste (spent coffee bean powder) as reinforcement in cellulose matrix for packaging applications

As the annual production of the solid waste generable in the form of spent coffee bean powder (SCBP) is over 6 million tons, its utilization in the generation of green energy, waste water treatment and as a filler in biocomposites is desirable. The objective of this article is to analyze the possibilities to valorize coffee bean powder as a filler in cellulose matrix. Cellulose matrix was dissolved in the relatively safer aqueous solution mixture (8% LiOH and 15% Urea) precooled to -12.5°C. To the cellulose solution (SCBP) was added in 5-25wt% and the composite films were prepared by regeneration method using ethyl alcohol as a coagulant. Some SCBP was treated with aq. 5% NaOH and the composite films were also prepared using alkali treated SCBP as a filler. The films of composites were uniform with brown in color. The cellulose/SCBP films without and with alkali treated SCBP were characterized by FTIR, XRD, optical and polarized optical microscopy, thermogravimetric analysis (TGA) and tensile tests. The maximum tensile strength of the composite films with alkali treated SCBP varied between (106-149MPa) and increased with SCBP content when compared to the composites with untreated SCBP. The thermal stability of the composite was higher at elevated temperatures when alkali treated SCBP was used. Based on the improved tensile properties and photo resistivity, the cellulose/SCBP composite films with alkali treated SCBP may be considered for packaging and wrapping of flowers and vegetables.

Biosurfactant rhamnolipid enhanced modification of corn stalk and its application for sorption of phenanthrene

The application of modified agricultural wastes for removing polycyclic aromatic hydrocarbons (PAHs) from water is gaining a growing interest. However, most modified methods using synthetic chemicals may cause secondary pollution. To overcome this limitation, in this study, a rhamnolipid modified corn stalk (RL-CS) for the removal of phenanthrene (PHE) from aqueous solution was prepared using a rhamnolipid-enhanced acid modification method. RL-CS with higher surface area and lower polarity exhibited higher PHE removal efficiency than that of raw corn stalk (RCS). The adsorption kinetics of RL-CS fitted well with pseudo-second-order kinetics (R² > 0.999). Sorption coefficients and carbon-normalized sorption coefficient of RL-CS were 4.68 and 2.86 times higher than that of RCS. Sorption process of RL-CS was nonlinear. Meanwhile, the sorption was an exothermic process and could occur spontaneously. The present study demonstrated that biosurfactant-modified biosorbent RL-CS may be of great potential for the removal of low concentrations of PAHs from the contaminated waters.

Nanostructured cellulose-xyloglucan blends via ionic liquid/water processing

In this work, the properties of cellulose (CE)/xyloglucan (XG) biopolymer blends are investigated, taking inspiration from the outstanding mechanical properties of plant cell walls. CE and XG were first co-solubilized in an ionic liquid, 1-ethyl-3-methylimidazolium acetate, in order to blend these biopolymers with a varying CE:XG ratio. The biopolymers were then regenerated together using water to produce solid blends in the form of films. Water-soluble XG persisted in the films following regeneration in water, indicating an attractive interaction between the CE and XG. The final CE:XG ratio of the blends was close to the initial value in solutions, further suggesting that intimate mixing takes place between CE and XG. The resulting CE/XG films were found to be free of ionic liquid, transparent and with no evidence of phase separation at the micron scale. The mechanical properties of the blend with a CE:XG ratio close to one revealed a synergistic effect for which a maximum in the elongation and stress at break was observed in combination with a high elastic modulus. Atomic force microscopy indicates a co-continuous nanostructure for this composition. It is proposed that the non-monotonous variation of the mechanical performance of the films with XG content is due to this observed nanostructuration.

Biosorption of alpacide blue from aqueous solution by lignocellulosic biomass: Luffa cylindrica fibers

The aim of the present work is to develop an effective and inexpensive pollutant-removal technology using lignocellulosic fibers: Luffa cylindrica, for the biosorption of an anionic dye: alpacide blue. The influence of some experimental parameters such as pH, temperature, initial concentration of the polluted solution, and mass of the sorbent L. cylindrica on the biosorption of alpacide blue by L. cylindrica fibers has been investigated. Optimal parameters for maximum quantity of biosorption dye were achieved after 2 h of treatment in a batch system using an initial dye concentration of 20 mg/L, a mass of 1 g of L. cylindrica fibers, and pH 2. In these conditions, the quantity of dye retained is 2 mg/g and the retention rate is 78 %. Finally, a mathematical modeling of kinetics and isotherms has been used for mathematical modeling; the model of pseudo-second order is more appropriate to describe this phenomenon of biosorption. Concerning biosorption isotherms, the Freundlich model is the most appropriate for a biosorption of alpacide blue dye by L. cylindrica fibers.

Multistage process for the production of bioethanol from almond shell

This work describes the feasibility of using almond shell as feedstock for bioethanol production. A pre-treatment step was carried out using 4% NaOH for 60min at 121°C followed by 1% sulfuric acid for 60min at 121°C. Enzymatic saccharification of the pre-treated almond shell was performed using Penicillium occitanis enzymes. The process was optimized using a hybrid design with four parameters including the incubation time, temperature, enzyme loads, and polyethylene glycol (PEG) concentration. The optimum hydrolysis conditions led to a sugar yield of 13.5%. A detoxification step of the enzymatic hydrolysate was carried out at pH 5 using 1U/ml of laccase enzyme produced by Polyporus ciliatus. Fermenting efficiency of the hydrolysates was greatly improved by laccase treatment, increasing the ethanol yield from 30% to 84%. These results demonstrated the efficiency of using almond shell as a promising source for bioethanol production.

Synthesis of iron oxyhydroxide-coated rice straw (IOC-RS) and its application in arsenic(V) removal from water

Because of the recognition that arsenic (As) at low concentrations in drinking water causes severe health effects, the technologies of As removal have become increasingly important. In this study, a simplified and effective method was used to immobilize iron oxyhydroxide onto a pretreated naturally occurring rice straw (RS). The modified RS adsorbent was characterized, using scanning electron microscope, Fourier transform infrared spectroscopy, thermogravimetric analyzer, and surface area analyzer. Experimental batch data of As(V) adsorption were modeled by the isotherms and kinetics models. Although all isotherms, the Langmuir model fitted the equilibrium data better than Freundlich and Dubinin-Radushkevich models and confirmed the surface homogeneity of adsorbent. The iron oxyhydroxide-coated rice straw (IOC-RS) was found to be effective for the removal of As(V) with 98.5% sorption efficiency at a concentration of <50 mg/L of As(V) solution, and thus maximum uptake capacity is ∼22 and 20 mg As(V)/g of IOC-RS at pH 4 and 6, respectively. The present study might provide new avenues to achieve the As concentrations required for drinking water recommended by the World Health Organization.

A Multi-Analytical Approach for the Evaluation of the Efficiency of the Conservation-Restoration Treatment of Moroccan Historical Manuscripts Dating to the 16th, 17th, and 18th Centuries

The most critical steps during the conservation-restoration treatment applied in Moroccan libraries are the deacidification using immersion in a saturated aqueous calcium hydroxide (Ca(OH)2) solution and the consolidation of degraded manuscripts using Japanese paper. The present study aims to assess the efficiency of this restoration method using a multi-analytical approach. For this purpose, three ancient Arabic Moroccan manuscript papers dating back to the 16th, 17th, and 18th centuries were investigated to characterize the paper support and make a comparative study between pre-restoration and post-restoration states. Three structural and molecular characterization techniques including solid-state nuclear magnetic resonance spectroscopy on (13)C with cross-polarization and magic-angle spinning nuclear magnetic resonance ((13)C CP-MAS NMR), attenuated total reflectance Fourier transform infrared spectroscopy (ATR FT-IR), and X-ray diffraction (XRD) were used to elucidate the cellulose main features, to identify the inorganic composition of the papers, and to study the crystallinity of the samples. Inductively coupled plasma atomic emission spectrometry (ICP-AES) allowed us to obtain a qualitative and quantitative characterization of the mineral fillers used in the manufacturing of the papers. Scanning electron microscopy coupled to energy dispersive spectrometry (SEM-EDS) ascertained the state of conservation of the different papers and helped us to study the elemental composition of the samples. After restoration, it was shown that the deacidification improved the stability of papers by providing an important alkaline buffer, as demonstrated using FT-IR and energy dispersive spectrometry (EDS) results. However, XRD and ICP-AES did not confirm the pertinence of the treatment for all samples because of the unequal distribution of Ca on the paper surface during the restoration. The consolidation process was studied using SEM analysis; its effectiveness in restoring torn areas was found to be significant.

Simultaneous recovery of organic and inorganic content of paper deinking residue through low-temperature microwave-assisted pyrolysis

Significant amounts of paper deinking residue (DIR) has been and is still being generated from paper deinking processes, representing both an economic and environmental burden for recycled paper mills. Our research on low-temperature (<200 °C) microwave-assisted (MW-assisted) pyrolysis of DIR allows for simultaneously efficient fast separation and recovery of the organic and inorganic content of DIR at relatively low temperature and within 15 min. Our study is the first highly detailed account of the use low-temperature MW-assisted pyrolysis to effect this change. The obtained liquid and solid products were characterized by a variety of analytical techniques (e.g., attenuated total reflection infrared, gas chromatography-mass spectrometry, liquid-state nuclear magnetic resonance (NMR), X-ray diffraction, solid-state cross-polarization/magic-angle spinning (13)C NMR, and Bloch-decay (13)C NMR). The results reveal that the process efficiently separates the inorganic minerals as microwave residue (mainly calcite and kaolinite) from organic matter, and hence the microwave residue could be reused to produce new paper/cardboard products. The organic fraction bio-oil generated is energy-densified and rich in carbohydrates and is a potential source for valuable aromatic compounds.

Conservation of Moroccan manuscript papers aged 150, 200 and 800 years. Analysis by infrared spectroscopy (ATR-FTIR), X-ray diffraction (XRD), and scanning electron microscopy energy dispersive spectrometry (SEM-EDS)

The preservation of manuscripts and archive materials is a serious problem for librarians and restorers. Paper manuscript is subjected to numerous degradation factors affecting their conservation state. This research represents an attempt to evaluate the conservation restoration process applied in Moroccan libraries, especially the alkaline treatment for strengthening weakened paper. In this study, we focused on six samples of degraded and restored paper taken from three different Moroccan manuscripts aged 150, 200 and 800 years. In addition, the Japanese paper used in restoration has been characterized. A modern paper was also analyzed as reference. A three-step analytical methodology based on infrared spectroscopy (ATR-FTIR), X-ray diffraction (XRD) and scanning electron microscopy coupled to energy dispersive spectrometry (SEM-EDS) analysis was developed before and after restoration in order to determine the effect of the consolidation treatment on the paper structure. The results obtained by XRD and ATR-FTIR disclosed the presence of barium sulfate (BaSO4) in all restored paper manuscripts. The presence of calcium carbonate (CaCO3) in all considered samples was confirmed by FTIR spectroscopy. The application of de-acidification treatment causes significant changes connected with the increase of intensity mostly in the region 1426 cm(-1), assigned to the asymmetric and symmetric CO stretching mode of calcite, indicating the effectiveness of de-acidification procedure proved by the rise of the alkaline reserve content allowing the long term preservation of paper. Observations performed by SEM magnify the typical paper morphology and the structure of fibbers, highlighting the effect of the restoration process, manifested by the reduction of impurities.