Catalytic oxidation of gaseous benzene with ozone over zeolite-supported metal oxide nanoparticles at room temperature

Electronic-Structure-Modulated Cu,Co-Coanchored N-Doped Nanocarbon as a Difunctional Electrocatalyst for Hydrogen Evolution and Oxygen Reduction Reactions

To alleviate the problems of environmental pollution and energy crisis, aggressive development of clean and alternative energy technologies, in particular, water splitting, metal-air batteries, and fuel cells involving two key half reactions comprising hydrogen evolution reaction (HER) and oxygen reduction (ORR), is crucial. In this work, an innovative hybrid comprising heterogeneous Cu/Co bimetallic nanoparticles homogeneously dispersed on a nitrogen-doped carbon layer (Cu/Co/NC) was constructed as a bifunctional electrocatalyst toward HER and ORR via a hydrothermal reaction along with post-solid-phase sintering technique. Thanks to the interfacial coupling and electronic synergism between the Cu and Co bimetallic nanoparticles, the Cu/Co/NC catalyst showed improved catalytic ORR activity with a half-wave potential of 0.865 V and an excellent stability of more than 30 h, even compared to 20 wt% Pt/C. The Cu/Co/NC catalyst also exhibited excellent HER catalytic performance with an overpotential of below 149 mV at 10 mA/cm2 and long-term operation for over 30 h.

Highly Dispersed Ni Atoms and O3 Promote Room-Temperature Catalytic Oxidation

Transition metal oxides are promising catalysts for catalytic oxidation reactions but are hampered by low room-temperature activities. Such low activities are normally caused by sparse reactive sites and insufficient capacity for molecular oxygen (O2) activation. Here, we present a dual-stimulation strategy to tackle these two issues. Specifically, we import highly dispersed nickel (Ni) atoms onto MnO2 to enrich its oxygen vacancies (reactive sites). Then, we use molecular ozone (O3) with a lower activation energy as an oxidant instead of molecular O2. With such dual stimulations, the constructed O3-Ni/MnO2 catalytic system shows boosted room-temperature activity for toluene oxidation with a toluene conversion of up to 98%, compared with the O3-MnO2 (Ni-free) system with only 50% conversion and the inactive O2-Ni/MnO2 (O3-free) system. This leap realizes efficient room-temperature catalytic oxidation of transition metal oxides, which is constantly pursued but has always been difficult to truly achieve.

Thermal Annealing Induced Surface Oxygen Vacancy Clusters in α-MnO2 Nanowires for Catalytic Ozonation of VOCs at Ambient Temperature

Catalytic ozonation has gained considerable interest in volatile organic compound (VOC) elimination due to its mild reaction conditions. However, the low activity and mineralization rate of VOCs over catalysts hinder its practical application. Herein, a series of α-MnO2 nanowire catalysts were prepared via thermal annealing treatment at various temperatures to tailor defect species. Numerous characterization techniques were used and combined to investigate the relationship between activity and microstructure. PALS and XAFS indicated that more unsaturated manganese and oxygen vacancies, especially surface oxygen vacancy clusters, were produced in α-MnO2 under the optimal high calcination temperature. As a result, MnO2-600 was found to exhibit the best-ever performance in toluene conversion (95%) and mineralization rate (89.5%) at 20 °C, making it a promising candidate for practical use. The roles of these defects in manipulating the reactive oxygen species of α-MnO2 were clarified by quantifying the amounts of reactive oxygen species by quenching experiments and density functional theory calculations. 1O2 and ·OH species generated in the vicinity of oxygen vacancy clusters, especially the dimer oxygen vacancy cluster, were identified as key oxygen species in the abatement of toluene. This study provides a facile method to engineer the microstructure of MnO2 by means of the manipulation of oxygen vacancies and an in-depth understanding of their roles in the catalytic ozonation of VOC.

Mitigation of hazardous toluene via ozone-catalyzed oxidation using MnOx/Sawdust biochar catalyst

This study investigated catalytic ozone oxidation using a sawdust char (SDW) catalyst to remove hazardous toluene emitted from the chemical industry. The catalyst properties were analyzed by proximate, ultimate, nitrogen adsorption-desorption isotherms, Fourier-transform infrared, and X-ray photoelectron spectroscopy analyses. In addition, hydrogen-temperature programmed reduction experiments were conducted to analyze the catalyst properties. The specific area and formation of micropores of SDC were improved by applying KOH treatment. MnOx/SDC-K3 exhibited a higher toluene removal efficiency of 89.7% after 100 min than MnOx supported on activated carbon (MnOx/AC) with a removal efficiency of 6.6%. The higher (O_ads (adsorbed oxygen)+O_v(vacancy oxygen))/O_L (lattice oxygen) and Mn³⁺/Mn⁴⁺ ratios of MnOx/SDC-K3 than those of MnOx/AC seemed to be important for the catalytic oxidation of toluene.

Designing oxide chemiresistors for detecting volatile aromatic compounds: recent progresses and future perspectives

Oxide chemiresistors have mostly been used to detect reactive gases such as ethanol, acetone, formaldehyde, nitric dioxide, and carbon monoxide. However, the selective and sensitive detection of volatile aromatic compounds such as benzene, toluene, and xylene, which are extremely toxic and harmful, using oxide chemiresistors remains challenging because of the molecular stability of benzene rings containing chemicals. Moreover, the performance of the sensing materials is insufficient to detect trace concentration levels of volatile aromatic compounds, which lead to harmful effects on human beings. Here, the strategies for designing highly selective and sensitive volatile aromatic compound gas sensors using oxide chemiresistors were suggested and reviewed. Key approaches include the use of thermal activation, design of sensing materials with high catalytic activity, the utilization of catalytic microreactors and bilayer structures with catalytic overlayer, and the pretreatment of analyte gases or post analysis of sensing signals. In addition, future perspectives from the viewpoint of designing sensing materials and sensor structures for high-performance and robust volatile aromatic compounds gas sensors are provided. Finally, we discuss possible applications of the sensors and sensor arrays.

Catalytic ozonation of VOCs at low temperature: A comprehensive review

VOCs abatement has attracted increasing interest because of the detrimental effects on both atmospheric environment and human beings of VOCs. The assistance of ozone has enabled efficient VOCs removal at low temperature. Thereby, catalytic ozonation is considered as one of the most feasible and effective methods for VOCs elimination. This work systematically reviews the emerging advances of catalytic ozonation of different VOCs (i.e., aromatic hydrocarbons, oxygenated VOCs, chlorinated VOCs, sulfur-containing VOCs, and saturated alkanes) over various functional catalysts. General reaction mechanism of catalytic ozonation including both Langmuir-Hinshelwood and Mars-van-Krevelen mechanisms was proposed depending on the reactive oxygen species involving the reactions. The influence of reaction conditions (water vapor and temperature) is fully discussed. This review also introduces the enhanced VOCs oxidation via catalytic ozonation in the ozone-generating systems including plasma and vacuum ultraviolet. Lastly, the existing challenges of VOCs catalytic ozonation are presented, and the perspective of this technology is envisioned.

Catalytic ozone oxidation toluene over supported manganese cobalt composite: influence of catalyst support

In this study, the manganese cobalt composite (Mn-Co)-loaded SiO₂, MgO, TiO₂, γ-Al₂O₃ and silicalite-1 were prepared by ultrasonic complexation method. The catalysts were characterized by XRD, BET, SEM, TEM, H₂-TPR and XPS, and the activity of catalytic oxidation of toluene was evaluated. It was found that Mn-Co loaded γ-Al₂O₃ (Mn₂CoO_x/γ-Al₂O₃) exhibited excellent catalytic activity. When the gas hour space velocity (GHSV) was 45,000 h^-1, the removal rate of toluene reached 91.2% within 5.5 h, and the selectivity of CO₂ was 71.10% at ambient temperature. The operation of Mn₂CoO_x/γ-Al₂O₃ at different temperatures was investigated, and the better toluene removal efficiency more than 80% after reacting 9h was obtained at 50 °C. The characterization results showed that better catalytic activity is related to smaller grain size, higher Mn³⁺/Mn⁴⁺ values and the relative content of active oxygen species (O_II + O_III). Increased amounts of low state species easily led to the imbalance of the catalyst surface charge and promoted the formation of more oxygen vacancies.

Effectiveness of toluene mineralization by gas-phase oxidation over Co(II)/SiO2 catalyst with ozone

The results of experimental study on effectiveness of gas-phase total oxidation of toluene towards carbon dioxide and water with the aid of ozone over Co(II)/SiO₂ catalyst are presented in this work. The main objective of the work was to determine ozone demand necessary for total mineralization of toluene at the temperature range of 40-100°C chosen to minimize catalyst poisoning by water. Complete mineralization of toluene was possible if sufficient ozone/toluene ratio was maintained in the gas supplied to the reactor. For ozone/toluene molar ratios less than 20 the extent of toluene mineralization increased with temperature up to a plateau starting at approximately 60°C, which was caused by ozone shortage. Stoichiometry of the total oxidation of toluene with ozone indicates that only one oxygen atom in the ozone molecule is used for the oxidation of toluene, to achieve complete mineralization. Experimentally determined ozone/toluene ratio (20-25) necessary for the total oxidation of toluene was larger than the theoretical one mostly due to ozone losses resulting from its 'unproductive' decomposition. At the range of lower values of mineralization rate, the toluene oxidation proceeds according to a more efficient mechanism, indicating less ozone demand being between 6 and 18 moles of ozone per mole of toluene. A possible mechanism of toluene oxidation was suggested. The mechanism involves the formation of •OH radicals, which may explain the effectiveness of Co(II)/SiO₂ catalyst in combination with ozone for the oxidation of toluene and other aromatic VOCs in a low-temperature process.

Catalytic Oxidation of CO and Benzene over Metal Nanoparticles Loaded on Hierarchical MFI Zeolite

In order to obtain highly active catalytic materials for oxidation of carbon monoxide and volatile organic compounds (VOCs), monometallic platinum, copper, and palladium catalysts were prepared by using of two types of ZSM-5 zeolite as supports—parent ZSM-5 and the same one treated by HF and NH₄F buffer solution. The catalyst samples, obtained by loading of platinum, palladium, and copper on ZSM-5 zeolite treated using HF and NH₄F buffer solution, were more active in the reaction of CO and benzene oxidation compared with catalyst samples containing untreated zeolite. The presence of secondary mesoporosity played a positive role in increasing the catalytic activity due to improved reactant diffusion. The only exception was the copper catalysts in the reaction of CO oxidation, in which case the catalyst, based on untreated ZSM-5 zeolite, was more active. In this specific case, the key role is played by the oxidative state of copper species loaded on the ZSM-5 zeolites.

Green Synthesis of Cu Nanoparticles in Modulating the Reactivity of Amine-Functionalized Composite Materials towards Cross-Coupling Reactions

Control over both dispersion and the particle size distribution of supported metal particles is of paramount importance for the catalytic activity of composite materials. We describe the synthesis of materials with Cu nanoparticles well-dispersed on different amine-functionalized supports, using the extract of Wallich Spurge as a green, reducing agent. Graphene oxide (GO), mesoporous silica (MCM-41), mesoporous zirconia, and reduced graphene oxide-mesoporous silica (RGO-MCM-41) were explored as supports. Cu nanoparticles were better stabilized on RGO-MCM-41 compared to other supports. The novel composite materials were characterized by X-ray diffraction (XRD), Raman spectra, Scanning electron microscope (SEM), Transmission electron microscopy analysis and HR-TEM. SEM and EDX techniques. High angle XRD confirmed the conversion of graphene oxide to reduced graphene oxide (RGO) with plant extract as a reducing agent. Both XRD and TEM techniques confirmed the Cu nanoparticle formation. The catalytic activity of all the prepared materials for the Ullmann coupling reactions of carbon-, oxygen-, and nitrogen-containing nucleophiles with iodobenzene was evaluated. From the results, 5 wt% Cu on amine-functionalized reduced graphene oxide/mesoporous silica nanocomposite (5 wt%Cu(0)-AAPTMS@RGO-MCM-41) exhibited excellent efficiency with 97% yield of the C-C coupling product in water at 80 °C in 5 h. The activity remained unaltered almost up to the fourth cycle. The Cu nanoparticles stabilized by organic amine group on RGO hybrid facilitated sustained activity.

Recent Progress in Metal-Organic Framework-Derived Nanostructures in the Removal of Volatile Organic Compounds

Air is the most crucial and life-supporting input from nature to the living beings of the planet. The composition and quality of air significantly affects human health, either directly or indirectly. The presence of some industrially released gases, small particles of anthropogenic origin, and the deviation from the normal composition of air from the natural condition causes air pollution. Volatile organic compounds (VOCs) are common contaminants found as indoor as well as outdoor pollutants. Such pollutants represent acute or chronic health hazards to the human physiological system. In the environment, such polluted gases may cause chemical or photochemical smog, leading to detrimental effects such as acid rain, global warming, and environmental pollution through different routes. Ultimately, this will propagate into the food web and affect the ecosystem. In this context, the efficient removal of volatile organic compounds (VOCs) from the environment remains a major threat globally, yet satisfactory strategies and auxiliary materials are far from being in place. Metal–organic frameworks (MOFs) are known as an advanced class of porous coordination polymers, a smart material constructed from the covalently bonded and highly ordered arrangements of metal nodes and polyfunctional organic linkers with an organic–inorganic hybrid nature, high porosities and surface areas, abundant metal/organic species, large pore volumes, and elegant tunability of structures and compositions, making them ideal candidates for the removal of unwanted VOCs from air. This review summarizes the fundamentals of MOFs and VOCs with recent research progress on MOF-derived nanostructures/porous materials and their composites for the efficient removal of VOCs in the air, the remaining challenges, and some prospective for future efforts.

Al2O3/CuI/PANI nanocomposite catalyzed green synthesis of biologically active 2-substituted benzimidazole derivatives

This work is generally focused on the synthesis of an efficient, reusable and novel heterogeneous Al2O3/CuI/PANI nanocatalyst, which has been well synthesized by a simple self-assembly approach where aniline is oxidized into PANI and aniline in the presence of KI also acts as a reductant. The nanocatalyst was well characterized by XRD, FTIR, SEM, EDX, TEM, BET and XPS techniques. In this study, the fabricated material was employed for the catalytic one-pot synthesis of 2-substituted benzimidazoles via condensation between o-phenylenediamine and aldehydes in ethanol as a green solvent. The present method is facile and offers several advantages such as high % yield, less reaction time, and no use of additive/bases. Also, the catalyst showed better values of green metrics including low E-factor: 0.17, high reaction mass efficiency: 85.34%, high carbon efficiency: 94%, and high process mass intensity: 1.17.

In situ synthesis of a hybrid Fe(Co)/MXene/ZSM-5 catalyst for phenol abatement

MXene (Ti3C2) was introduced to develop the multifunctional photocatalyst Metal/MXene/ZSM-5 to enhance the catalytic efficiency of the ZSM-5 based catalyst.

Comparative investigation on catalytic ozonation of VOCs in different types over supported MnOx catalysts

This paper conducted catalytic ozonation of CB (chlorobenzene) over a series of MnO_x based catalysts with different supports (Al₂O₃, TiO₂, SiO₂, CeO₂, and ZrO₂) at 120 °C. Mn/Al₂O₃ exhibited highest CB conversion efficiency, ca. 82.92 %, due to its excellent textual properties, O₂ desorption, redox ability, and desirable surface adsorbed oxygen species and acidity. O₃ conversion all approached nearly 100.0%, with residual <10 ppm. Mn/Al₂O₃ was further employed to investigate effect of temperature, O₃/CB, and space velocity on CB conversion. Hereafter, catalytic ozonation of single and binary VOCs in different types was performed, i.e., CB, DCE (dichloroethane), DCM (dichloromethane), and PhH (Benzene). Conversion results demonstrated aromatics degraded easier than alkanes and more carbon atoms decreased difficulty, as CB∼PhH > DCE∼DCM, and DCE > DCM; but chlorinated substitution increased difficulty, as PhH > CB. Catalytic co-ozonation of CB/DCE indicated that DCE significantly improved CB conversion to reach totally degradation at low O₃ input, but inhibited DCE conversion, especially at higher ratio of DCE/CB. Co-ozonation improved ozone utilization efficiency, and maintained the original property of catalyst. By contrast, CB/PhH co-ozonation displayed very mild effects. Finally, critical intermediates during catalytic CB ozonation, i.e., DCM, carboxyl and formic acid, were detected from mass spectrum results.

Complete Degradation of Gaseous Methanol over Pt/FeOx Catalysts by Normal Temperature Catalytic Ozonation

Normal temperature catalytic ozonation (NTCO) is a promising yet challenging method for the removal of volatile organic compounds (VOCs) because of limited activity of the catalysts at ambient temperature. Here, we report a series of Pt/FeO_x catalysts prepared by the co-precipitation method for NTCO of gaseous methanol. All samples were found to be active and among them, the Pt/FeO_x-400 (calcined at 400 °C) catalyst with a Pt cluster loading of 0.2% exhibited the highest activity, able to completely convert methanol into CO₂ and H₂O at 30 °C. Extensive experimental research suggested that the superior catalytic activity could be attributed to the highly dispersed Pt clusters and an appropriate molar ratio of Pt⁰/Pt²⁺. Furthermore, electron paramagnetic resonance and density functional theory computational studies revealed the mechanism that the Pt/FeO_x-400 catalyst could activate O₃ and water effectively to produce hydroxyl radicals responsible for the catalytic oxidation of methanol. The findings of this work may foster the development of technologies for normal temperature abatement of VOCs with low energy consumption.

Effect of different nitric acid concentrations on manganese/activated carbon-modified catalysts for the catalytic ozonation of toluene

In this work, the effect of nitric acid modification on activated carbon (AC) and on properties of Mn/AC ozone catalysts was studied.

Role of PM2.5 in the photodegradation of the atmospheric benzene

The presence of PM_2.5 may affect the photodegradation of benzene in the natural atmosphere. On one hand, the photodegradation of benzene may be promoted with the increase in PM_2.5 concentrations, owing to adsorption and catalysis effect of PM_2.5 surface; On the other hand, PM_2.5 can scatter or block ultraviolet light and lead to weakening the photochemical reactions in the atmospheric system. It is very difficult to prove which process is dominant in the real atmosphere due to the complexity of the atmosphere. Based on coupling detrended fluctuation analysis, the goal of this work is to reveal the role of PM_2.5 in the photodegradation of benzene in real atmosphere over long time scales. The 9 years regular monitoring data from 2007 to 2016 in Puzi of Taiwan are analyzed. A new nonlinear parameter (PDB) is established to characterize the photodegradation degree of atmospheric benzene. Based on sliding window technique, the correlations between the temporal variation of PDB and PM_2.5 are analyzed. The results show that there is a positive correlation between PDB and PM_2.5 in daytime and little correlation between them in nighttime. It indicates that PM_2.5 mainly plays the promoting effect on the photodegradation of atmospheric benzene. This is the first study to directly determine the role of PM_2.5 in the photochemical behavior of atmospheric benzene based on long term field observation data. Moreover, the results suggest that the regional transport of PM_2.5 could seriously affect the geochemistry cycle of some VOCs. This research provides a new analysis method to directly quantify the effect of PM_2.5 on the photodegradation of VOCs in the real atmosphere. It is helpful for evaluating the role of PM_2.5 in the complex photochemical system.

Catalytic oxidation of VOCs over Mn/TiO2/activated carbon under 185 nm VUV irradiation

Volatile organic compounds (VOCs) are regarded as the major contributors to air pollution, and should be strictly regulated. Photocatalytic oxidation (PCO) is of great interest for the removal of VOCs owing to its strong oxidation capability. However, its application is greatly limited by catalytic deactivation. Vacuum Ultraviolet (VUV) irradiation provides a novel way to improve the photocatalytic activity while much O₃ will be generated which may cause secondary pollution. In this study, a multi-functional catalyst of Mn/TiO₂/activated carbon (AC) was developed to eliminate and utilize O₃, as well as enhance catalytic oxidation of VOC degradation via ozone-assisted catalytic oxidation (OZCO). The results indicate that Mn modified TiO₂/AC (i.e. 0.1%Mn/20%TiO₂/AC) achieved a toluene removal efficiency of nearly 86% with 100% elimination rate of O₃. With the help of Mn/TiO₂/AC catalyst, O₃ was catalytically decomposed and transformed into active species of O (¹D) and OH, thus enhancing toluene removal. The combination of VUV irradiation with multi-functional catalyst provides a novel and efficient way for the degradation of VOCs.

Ozone assisted oxidation of gaseous PCDD/Fs over CNTs-containing composite catalysts at low temperature

Ozone assisted carbon nanotubes (CNTs) supported vanadium oxide/titanium dioxide (V/Ti-CNTs) or vanadium oxide-manganese oxide/titanium dioxide (V-Mn/Ti-CNTs) catalysts towards gaseous PCDD/Fs (polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans) catalytic oxidations at low temperature (150 °C) were investigated. The removal efficiency (RE) and decomposition efficiency (DE) of PCDD/Fs achieved with V-Mn/Ti-CNTs alone were 95% and 45% at 150 °C under a space velocity (SV) of 14000 h^-1; yet, these values reached 99% and 91% when catalyst and low concentration (50 ppm) ozone were used in combined. The ozone promotion effect on catalytic activity was further enhanced with the addition of manganese oxide (MnO_x) and CNTs. Adding MnO_x and CNTs in V/Ti catalysts facilitated the ozone decomposition (creating more active species on catalyst surface), thus, improved ozone utilization (demanding relatively lower ozone addition concentration). On the other hand, this study threw light upon ozone promotion mechanism based on the comparison of catalyst properties (i.e. components, surface area, surface acidity, redox ability and oxidation state) before and after ozone treatment. The experimental results indicate that a synergistic effect exists between catalyst and ozone: ozone is captured and decomposed on catalyst surface; meanwhile, the catalyst properties are changed by ozone in return. Reactive oxygen species from ozone decomposition and the accompanied catalyst properties optimization are crucial reasons for catalyst activation at low temperature.

Efficiencies and mechanisms of ZSM5 zeolites loaded with cerium, iron, or manganese oxides for catalytic ozonation of nitrobenzene in water

Discharge of industrial wastewater causes water pollution. It is therefore necessary to treat wastewater prior to discharge. Catalytic ozonation processes (COP) using ZSM5 zeolites loaded with metallic (Ce, Fe, or Mn) oxides to remove nitrobenzene from water were investigated. The total organic carbon (TOC) removal by the COP treatment with NaZSM5-38, HZSM5-38, and NaZSM5-100 were increased by 6.7%, 23.1%, and 19.8%, respectively, in comparison with single ozonation efficiency (39.2%). The loadings of Ce, Fe, or Mn oxides increased the catalytic activity relative to ZSM5 zeolites alone. The Ce loaded material (Ce/NaZSM5-38) had the highest TOC removal (86.3%). The different-metallic-oxides loaded zeolites exhibited different chemical processes during the removal of nitrobenzene from water. During COP treatment, NaZSM5-38 zeolites removed nitrobenzene mainly via OH mediated oxidation. HZSM5-38 and NaZSM5-100 zeolites showed powerful adsorption toward nitrobenzene. Both adsorption and direct ozonation contribute the TOC removal in their early uses. The OH mediated oxidation dominates the TOC removal process as the adsorption became saturated after multiple uses. Surface SiO bonds and/or SiO(H)Al structures are the active sites for ZSM5 zeolites. Efficient surface dispersion of the metallic oxides enhances the catalytic activity. This study shows the high potentials of ZSM5 zeolites as catalysts in COP to efficiently treat refractory wastewaters.

Aerobic oxidative amidation of alkynes using titanium oxide encapsulated cuprous iodide nanoparticles (CuI@TiO2)

A catalyst consisting of titanium oxide encapsulated cuprous iodide nanoparticles was prepared via a sol–gel method using inexpensive raw materials and was harnessed successfully in the oxidative amidation of alkynes via an environmentally benign and sustainable protocol.