Efficient Fe(III)/Fe(II) cycling triggered by MoO2 in Fenton reaction for the degradation of dye molecules and the reduction of Cr(VI)

Optimizing the thiosulfate-mediated zerovalent iron/persulfate activation systems: Trade-off between Fe(III)/Fe(II) cycling and quenching effects in environmental remediation

The remediation of organic-contaminated water is a critical environmental challenge, and iron-based persulfate (PS) activation processes have emerged as a promising solution. However, the introduction of reductive sulfur species, while accelerating the Fe(III)/Fe(II) redox cycle, may also quench reactive species, potentially compromising the efficiency of Fenton-like systems. Here we systematically investigate the trade-off between accelerated Fe(III)/Fe(II) cycling and quenching effects in the zerovalent iron/PS (ZVI/PS) system using thiosulfate (TSF) as an activator. Our results show that low-level TSF (0.03-1.00 mmol/L) effectively facilitated the removal of naphthalene (Nap) and atrazine (ATZ), respectively. This enhancement is attributed to accelerated ZVI dissolution and FeSx formation, which promote the Fe(III)/Fe(II) cycle, with Fe(IV) was identified as the primary active species. However, high-level TSF (>1.0 mmol/L) drastically reduced Nap removal due to PS consumption and active species elimination. The optimal TSF dosage of 0.20 mmol/L (TSF/PS molar ratio of 1:10) demonstrated robust organic pollutant degradation, achieving a 22-fold increase in the rate constant (kobs) for Nap removal and 0.47-7.5-fold increases for ATZ removal. These findings highlight the potential of the TSF-ZVI/PS system as a versatile and efficient solution for degrading a wide range of organic pollutants, including PAHs and herbicides, in water treatment applications.

Phenolic acid-containing compounds enhanced Fe3+/peroxides processes for efficient removal of sulfamethoxazole in surface waters

Sulfamethoxazole (SMX) in surface waters has raised widespread concerns due to its potential environmental and biological hazards. In this study, the performance, mechanism, and environmental application of phenolic acid-containing compounds (PACCs) enhanced Fe3+/peroxides processes for SMX degradation were investigated. PACCs with two Ar-OH groups exhibited the lowest toxicity and the best enhancement performance (65%-66% of PDS, 47%-58% of PMS and 61%-63% of H2O2), which were attributed to the excellent chelating and reducing ability towards Fe3+. Free radicals played the predominant role in PDS (37% of SO4-·, 34% of ·OH), PMS (37% of SO4-·, 35% of ·OH) and H2O2 (61% of ·OH) oxidation processes. FeIVO2+ play a non-negligible role in PDS and PMS processes (ŋ[PMSO2] = 52%-80% and ŋ[PMSO2] = 59%-72%). PDS and PMS processes were suitable for a pH range of 3.0-9.0, while the H2O2 process was 3.0-10.0. PDS and PMS processes exhibited stronger resistance to the common anions in surface waters. PMS process exhibited higher adaptability to surface waters quality (92%-98%). This study provides a novel approach for enhancing the degradation of SMX in natural surface waters.

Efficient activation of peracetic acid by defect-engineered MoO2-x: Oxygen vacancies and surface Mo(Ⅴ)-mediated electron transfer processes

The role of defect regulation of transition metal catalysts in peracetic acid (PAA) activation is equivocal. To reveal the corresponding mechanism, this work provides a high-efficiency and eco-friendly catalyst (MoO2-x) for PAA activation by introducing various degrees of oxygen vacancies on the MoO2 surface. Interestingly, 95.83 % of tetracycline (TC) is rapidly degraded by MoO2-x with rich oxygen vacancies within 20 min via PAA activation, which is superior over that of MoO2-x with poor oxygen vacancies and other typical oxidants (H2O2, SO32-, S2O82-, HSO5-, IO4-). In addition, the defect-regulated MoO2-x exhibits good de-biotoxicity towards TC. Moreover, MoO2-x shows satisfactory purification of various contaminants and actual pharma wastewater. Active species identification suggests that the electron transfer process triggered by the active complex (MoO2-x -PAA*) of PAA bonded on the MoO2-x surface plays the dominant role in TC degradation, while •OH plays a minor role. Mechanism analysis reveals that oxygen vacancies play an indispensable role in accelerating the adsorption and complexation of PAA as well as improving electrical conductivity. Active site analysis demonstrates that Mo(Ⅴ) on the MoO2-x surface acts as an electron shuttle and is the main PAA activation site. This work provides a new approach into the application of MoO2 in hospital wastewater purification via defect engineering.

Critical role of soil-applied molybdenum dioxide composite biochar material in enhancing Cr(VI) remediation process: The driver of Fe(III)/Fe(II) redox cycle

Heavy metal contamination of agricultural land due to sewage irrigation, over-application of fertilizers and pesticides, and industrial activities. Biochar, due to its rich functional groups and excellent electrochemical performance, is used for the remediation of heavy metal-contaminated farmland. However, the remediation mechanism remains uncertain due to the influence of minerals and multi-element composite pollution on soil. Therefore, introducing transition metal oxide MoO2 to prepare biochar composite remediation materials enhances the adsorption and reduction of soil Cr (Ⅵ). This study compared the differences in Cr (Ⅵ) improvement under different pollution systems and pH conditions and explored the potential mechanism of Fe (Ⅲ)/Fe (Ⅱ) redox cycling in Cr (Ⅵ) remediation. The results showed that both biochar MoO2 ball-milling composite (BC + M) and biochar-loaded MoO2 (BC/M) retained the original biochar (BC) remediation method for Cr (Ⅵ). Among them, the remediation of BC/M was the most stable, with the maximum remediation value ranging from approximately 6.52 to 58.58 mg/kg. In different pollution systems, Cd and Pb exhibited competitive adsorption toward Cr (Ⅵ), but they enhanced Cr (Ⅵ) remediation by promoting adsorption and self-complexation. In acidic conditions (pH = 4), BC/M showed the best remediation effect, with a reduction kinetic constant of 34.61 × 10-3 S-1 and a maximum adsorption capacity of 61.64 mg/g. Fe (Ⅲ)/Fe (Ⅱ) redox cycling accelerated the reduction of Cr (Ⅵ) (R2 = 0.81), and MoO2 promoted the Fe (Ⅲ)/Fe (Ⅱ) redox cycle. BC/M enhanced the Fe (Ⅱ) formation efficiency by 66.39% and 71.81% compared to BC + M and BC at pH = 4. The introduction of MoO2 and biochar composite materials enhanced the reduction process of Cr (Ⅵ), with BC/M achieving the optimal remediation level. This study reveals the potential mechanisms of MoO2 and biochar composite materials in soil Cr (Ⅵ) remediation, providing a reference and insight for the preparation of Cr (Ⅵ) remediation materials and the treatment of contaminated farmland.

Co-catalysis strategy for low-oxidant-consumption Fenton-like chemistry: From theoretical understandings to practical applications and future guiding strategies

Recently, great effects have been made for the co-catalysis strategy to solve the bottlenecks of Fenton system. A series of co-catalysis strategies using various inorganic metal co-catalysts and organic co-catalysts have been developed in various oxidant (i.e., hydrogen peroxide (H2O2) and persulfate) systems with significantly promotion of catalytic performances and lower oxidant consumption (only 5-10 % of conventional Fenton/Fenton-like systems). However, the developments of these co-catalysis strategies from theoretical understandings to practical applications and future guiding strategies were overlooked, which was an essential problem that must be considered for the future scale-up applications of co-catalysis systems. In this paper, these co-catalysis strategies with low-oxidant-consumption characteristics have been reviewed by the comparison of their co-catalysis mechanisms, as well as their advantages and disadvantages. We also discussed the recent developments of amplifying devices based on the co-catalysis systems. The scale-up performances of co-catalysis strategies based on these amplifying devices have also been assessed. In addition, future guiding strategies for the development of co-catalysis strategy with low-oxidant-consumption characteristics have also been first time outlined by the combination of the technical-economic analysis (TEA), life cycle assessment (LCA) and machine learning (ML). Finally, the paper systematically discusses the development opportunities, technical bottlenecks and future development directions of co-catalysis strategies with the prospect of large-scale applications. Basically, this work provides a systematic review on co-catalysis strategy with low-oxidant-consumption characteristic from theoretical understandings to practical applications and future guiding strategies.

A Critical Review of Deep Oxidation of Gaseous Volatile Organic Compounds via Aqueous Advanced Oxidation Processes

Volatile organic compounds (VOCs) are considered to be the most recalcitrant gaseous pollutants due to their high toxicity, diversity, complexity, and stability. Gas-solid catalytic oxidation methods have been intensively studied for VOC treatment while being greatly hampered by energy consumption, catalyst deactivation, and byproduct formation. Recently, aqueous advanced oxidation processes (AOPs) have attracted increasing interest for the deep oxidation of VOCs at room temperature, owing to the generation of abundant reactive oxygen species (ROS). However, current reviews mainly focus on VOC degradation performance and have not clarified the specific reaction process, degradation products, and paths of VOCs in different AOPs. This study systematically reviews recent advances in the application of aqueous AOPs for gaseous VOC removal. First, the VOC gas-liquid mass transfer and chemical oxidation processes are presented. Second, the latest research progress of VOC removal by various ROS is reviewed to study their degradation performances, pathways, and mechanisms. Finally, the current challenges and future strategies are discussed from the perspectives of synergistic oxidation of VOC mixtures, accurate oxidation, and resource utilization of target VOCs via aqueous AOPs. This perspective provides the latest information and research inspiration for the future industrial application of aqueous AOPs for VOC waste gas treatment.

Microstructure evolution and catalytic activity of AlCo1-xFeNiTiMox high entropy alloys fabricated by powder metallurgy route

This investigation presents the synthesis of equiatomic and non-equiatomic AlCo1-xFeNiTiMox (x = 0, 0.1, 0.25 and 1.0) high entropy alloys fabricated by mechanical alloying. Mo partially replaced Co. Classic thermodynamic calculations, such as mixing enthalpy (ΔHmix), configurational entropy (ΔSmix), the atomic size difference (δ), entropy to enthalpy ratio (Ω), electronegativity difference (△χ), and valence electron concentration (VEC) were used. Considering δ, Ω and VEC parameters, a BCC solid solution and an intermetallic phase can be predicted due to the partial replacement of Co by Mo. X-ray and electron diffraction of equiatomic HEA without Mo content revealed that after 35 h of milling, a Fe-type BCC lattice phase was formed in the alloy and two L21 phases, in addition to a minimal amount of FCC phase. As the Mo content increased, the Fe-type BCC phase was steadily replaced by the Mo-type BCC phase and the Fe-type FCC phase, and two L21 phases were also developed. When the 5 at% Mo-containing (x = 0.25) alloy was further milled for 80 h, the amount of phases remained almost the same; only the grain size was strongly reduced. The influence of the Mo addition on the properties of studied alloys was also confirmed in the decolourisation of Rhodamine B using a modified photo-Fenton process. The decolourisation efficiency within 20 min was 72% for AlCoFeNiTi and 87% for AlCo0.75FeNiTiMo0.25 using UV light with 365 nm wavelength.

Interfacial complexation between Fe3+ and Bi2MoO6 promote efficient persulfate activation via Fe3+/Fe2+ cycle for organic contaminates degradation upon visible light irradiation

To address the observed decrease in efficiency during Fe2+-mediated persulfate (PDS) activation caused by slow electron transfer rates and challenges in cycling between Fe3+/Fe2+ states, we devised a strategy to establish interfacial complexation between Fe3+ and Bi2MoO6 in the presence of PDS. The proposed approach facilitates more efficient capture of photogenerated electrons, thereby accelerating the rate-limiting reduction process of the Fe3+/Fe2+ cycle under visible light irradiation and promoting PDS activation. The Bi2MoO6/Fe3+/PDS/Vis system demonstrates complete degradation of organic pollutants, including Atrazine (ATZ), carbamazepine (CBZ), bisphenol A (BPA), and 2,4-dichlorophenol (DCP) at a concentration of 10 mg/L within a rapid reaction time of 30 min. Radical scavenging experiments and electron paramagnetic resonance spectra (EPR) confirm that the sulfate radical (•SO4-) is the dominant species responsible for organic contaminant degradation. The real-time conversion process between Fe3+ and Fe2+ was monitored by observing changes in iron species forms and concentrations within the reaction system. X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy verify the formation of a complexation between Fe3+ and Bi2MoO6, facilitating anchoring of Fe3+ onto material surface. Based on these findings, we propose a reliable mechanism for the activation reaction. This work presents a promising heterogeneous PDS activation method based on Fe3+/Fe2+ cycle for water treatment.

Synthesis of iron-boride/carbon-nitride composites and their applications in chemodynamic therapy

Chemodynamic therapy (CDT) is an emerging treatment strategy that inhibits tumor growth by catalyzing the generation of reactive oxygen species (ROS), such as hydroxyl radicals (•OH), using specific nanomaterials. Herein, we have developed a new class of iron-based nanomaterials, i.e., iron-based borides (FeB), using the superchaotropic effect of a boron cluster (closo-[B12H12]2-) and organic ligands, followed by high-temperature calcination. Experimental data and theoretical calculations revealed that FeB nanoparticles exhibit a Fenton-like effect, efficiently decomposing hydrogen peroxide into •OH and thus increasing the concentration of ROS. FeB nanomaterials demonstrate excellent catalytic performance, efficiently generate ROS, and exert significant antitumor effects in cell experiments and animal models. Therefore, FeB nanomaterials have considerable potential for application in tumor treatment and offer new insights for the development of novel and efficient cancer therapy strategies.

Effect and mechanism of norfloxacin removal by Eucalyptus leaf extract enhanced the ZVI/H2O2 process

The conventional ZVI/H2O2 technology suffers from poor reagent utilization, excess iron sludge generation, and strong low pH dependence. Therefore, eucalyptus leaf extract (ELE) was introduced to improve ZVI/H2O2 technology, and the efficacy and mechanism of ELE promoting ZVI/H2O2 technology were deeply explored. The results showed that the norfloxacin (NOR) removal and kobs of the ZVI/H2O2/ELE process were enhanced by 35.64 % and 3.27 times, respectively, compared to the ZVI/H2O2 process. In the ZVI/H2O2 process, the production of three reactive oxygen species (ROS: 1O2，·O2-，·OH) was effectively promoted by ELE so that the reaction efficacy was significantly enhanced. Moreover, the attack and degradation of pollutants by ROS was the main way to remove pollutants. With the introduction of ELE, the reactive sites on the catalyst appearance were increased to some extent, and the Fe(III)/Fe(II) cycle was improved. The analysis showed that ELE is rich in titratable acids and the ZVI/H2O2 technology is promoted mainly by lowering the pH of the process. In addition, the chelation of ELE and the reduction in pH by the ELE synergistically enhanced the ZVI/H2O2 technology, which significantly improved the reagent utilization (4.70 times for ZVI and 3.03 times for H2O2), broadened the pH range of the technology (6-9) and was able to effectively reduce the iron sludge contamination (30.33 %) of the process. Therefore, the study offers an important value to study eucalyptus leaves in micron-scale ZVI-Fenton technology.

Effective degradation of phenol by activating PMS with bimetallic Mo and Ni Co-doped g C3N4 composite catalyst: A Fenton-like degradation process promoted by non-free radical 1O2

The application of bimetal supported graphite phase carbon nitride in activated peroxymonosulfate (PMS) process has become a research hotspot in recent years. In this study, 8-g C3N4/Mo/Ni composite catalyst material was successfully prepared by doping Mo and Ni in graphite phase carbon nitride. The bimetallic active sites were formed in the catalyst, and PMS was activated by the metal valence Mo6+/Mo4+ and Ni2+/Ni(0) through redox double cycle to effectively degrade phenol. When pH was neutral, the degradation rate of 20 mg/L phenol solution with 8-g C3N4/Mo/Ni (0.35 g/L) and PMS (0.6 mM) could reach 95% within 20 min. The degradation rate of 8-g C3N4/Mo/Ni/PMS catalytic system could reach more than 90% within 20min under the condition of pH range of 3-11 and different anions. Meanwhile, the degradation effects of RhB, MB and OFX on different pollutants within 30min were 99%, 100% and 82%, respectively. Electron spin resonance and quenching experiments showed that in 8-g C3N4/Mo/Ni/PMS system, the degradation mechanism was mainly non-free radicals, and the main active species in the degradation process was 1O2. This study provides a new idea for the study of bimetal supported graphite phase carbon nitride activation of PMS and the theoretical study of degradation mechanism.

Carbon-coated copper nanocrystals with enhanced peroxidase-like activity for sensitive colorimetric determination of 2,4-dinitrophenylhydrazine

Carbon-coated copper nanocrystals (CuNCs) with peroxidase-like activity were hydrothermally prepared by using copper acetate, citric acid (CA) and histidine (His) as the precursors. Various shaped CuNCs, including urchin-like, slab-like and spherical appearance were facilely prepared by addition of different amount of NaNO2 in the precursor solutions. When 3,3',5,5'-tetramethylbenzidine (TMB) was used as the substrate, the CuNCs with urchin-like appearance have greatest peroxidase-like activity and their Michaelis-Menten constant (Km) and the maximum rate constant (νmax) are respectively 8.8 and 1.2 times higher than that obtained from horseradish peroxidase (HRP). The production of reactive oxygen species (ROS) was confirmed by radical quenching and electron spin resonance (ESR) tests. Subsequent studies have found that the CuNCs catalyzed color reaction of TMB can be selectively quenched by the environmental pollutant 2,4-dinitrophenylhydrazine (2,4-DNPH). Thus a new colorimetric method for the determination of 2,4-DNPH with a linear range of 0.60-20 µM was developed and a limit of detection (LOD) as low as 0.166 µM was achieved. The results obtained not only reveal the tunability of the peroxidase-like activity of Cu-based nanomaterials, but also provide a new method for the sensitive determination of environmental contaminate.

Anti-tumor activity of silymarin nanoliposomes in combination with iron: In vitro and in vivo study

Combination therapy represents a promising strategy in cancer management by reducing chemotherapy resistance and associated side effects. Silymarin (SLM) has been extensively investigated due to its potent antioxidant properties and demonstrated efficacy against cancer cells. Under certain conditions however, polyphenolic compounds may also exhibit prooxidant activity by elevating intracellular reactive oxygen species (ROS), which can harm the target cells. In this study, we hypothesized that the simultaneous administration of iron (Fe) could alter the antioxidant characteristic of SLM nanoliposomes (SLM Lip) to a prooxidant state. Hence, we first developed a SLM Lip preparation using lipid film method, and then investigated the anti-oxidant properties as well as the cytotoxicity of the liposomal preparation. We also explored the efficacy of concomitant administration of iron sucrose and SML Lip on the tumor growth and survival of mice bearing tumors. We observed that exposing cells to iron, and consecutive treatment with SLM Lip (Fe + SLM Lip) could induce greater toxicity to 4 T1 breast cancer cells compared to SLM Lip. Further, Fe + SLM Lip combination demonstrated a time-dependent effect on reducing the catalase activity compared to SLM Lip, while iron treatment did not alter cell toxicity and catalase activity. In a mouse breast cancer model, the therapeutic efficacy of Fe + SLM Lip was superior compared to SLM Lip, and the treated animals survived longer. The histopathological findings did not reveal a significant damage to the major organs, whereas the most significant tumor necrosis was evident with Fe + SLM Lip treatment. The outcomes of the present investigation unequivocally underscored the prospective use of Fe + SLM combination in the context of cancer therapy, which warrants further scrutiny.

Recent Progress of Covalent Organic Frameworks-Based Materials in Photocatalytic Applications: A Review

Covalent organic frameworks (COFs) are one type of porous organic materials linked by covalent bonds. COFs materials exhibit many outstanding characteristics such as high porosity, high chemical and thermal stability, large specific surface area, efficient electron transfer efficiency, and the ability for predesigned structures. These exceptional advantages enable COFs materials to exhibit remarkable performance in photocatalysis. Additionally, the activity of COFs materials as photocatalysts can be significantly upgraded by ion doping and the formation of heterojunctions. This paper summarizes the latest research progress on COF-based materials applied in photocatalytic systems. Initially, typical structures and preparation methods of COFs are analyzed and compared. Moreover, the essential principles of photocatalytic reactions over COFs-based materials and the latest research developments in photocatalytic hydrogen production, CO2 reduction, pollutants elimination, organic transformation, and overall water splitting are indicated. At last, the outlook and challenges of COF-based materials in photocatalysis are discussed. This review is intended to permit instructive guidance for the efficient use of photocatalysis based on COFs in the future.

Dual-functional single-atomic Mo/Fe clusters-decorated C3N5 via three electron-pathway in oxygen reduction reaction for tandemly removing contaminants from water

Inspired by the development of single-atom catalysts (SACs), the fabrication of multimetallic SACs can be a promising technical approach for the in situ electro-Fenton (EF) process. Herein, dual-functional atomically dispersed Mo-Fe sites embedded in carbon nitride (C3N5) (i.e., MoFe/C3N5) were synthesized via a facile SiO2 template method. The atomically isolated bimetallic configuration in MoFe/C3N5 was identified by combining the microscopic and spectroscopic techniques. The MoFe/C3N5 catalyst on the cathode exhibited a remarkable catalytic activity toward the three electron-dominated oxygen reduction reaction in sodium sulfate, leading to a highly effective EF reaction with a low overpotential for the removal of organic contaminants from wastewater. The new catalyst showed a superior performance over its conventional counterparts, owing to the dual functions of the dual-metal active sites. Density functional theory (DFT) analysis revealed that the dual-functional 50-MoFe/C3N5 catalyst enabled a synergistic action of the Mo-Fe dual single atomic centers, which can alter the adsorption/dissociation behavior and decrease the overall reaction barriers for effective organic oxidation during the EF process. This study not only sheds light on the controlled synthesis of atomically isolated catalyst materials but also provides deeper understanding of the structure-performance relationship of the nanocatalysts with dual active sites for the catalytic EF process. Additionally, the findings will promote the advanced catalysis for the treatment of emerging organic contaminants in water and wastewater.

Metal Borides as Excellent Co-Catalysts for Boosted and Long-Lasting Fenton-like Reaction: Dual Co-Catalytic Centers of Metal and Boron

The continuous electron supply for oxidant decomposition-induced reactive oxygen species (ROS) generation is the main contributor for the long-standing micropollutant oxidation in the iron-based advanced oxidation processes (AOPs). Herein, as a new class of co-catalysts, metal borides with dual active sites and preeminent conductive performance can effectively overcome the inherent drawback of Fenton-like reactions by steadily donating electrons to inactive Fe(III). Among the metal borides, tungsten boride (WB) exhibits a significant co-catalytic performance run ahead of common heterogeneous co-catalysts and exceptionally high stability. Based on qualitative and semi-quantitative tests, the hydroxyl radical, sulfate radical, and iron(IV)-oxo complex are all produced in the WB/Fe(III)/PDS system and Fe(IV)-induced methyl phenyl sulfoxide decomposition is up to 72%. Moreover, the production efficiency of ROS and relative proportions of radical and nonradical pathways change with various experimental conditions (dosages of PDS, WB, and solution pH) and water matrices. The rate-determining step of Fe(II) regeneration is greatly accelerated resulting from the synergetic effect between exposed metallic reactive sites and nonmetallic boron with reductive properties of WB. In addition, the self-dissolution of surface tungsten oxide and boron oxide leads to a renovated surface for sustainable Fe(III) reduction in long-term operations. Our discovery provides an efficient and sustainable strategy in the field of enhanced AOPs for water remediation.

Oxygen vacancies-dominated reactive species generation from peroxymonosulfate activated by MoO3-x for pollutant degradation

Interface oxygen vacancies (OVs) are commonly used to improve the catalytic performance of activators in persulfate-based advanced oxidation processes, but the underlying mechanism was not fully explored. This work reports a facile heat treatment method to regulate OVs in MoO_3-x to elucidate the mechanism of peroxymonosulfate (PMS) activated by OVs to degrade 2,4,4-Trichlorobiphenyl (PCB28). Electron spin resonance, free radical quenching, X-ray photoelectron spectroscopy, and Raman spectroscopy confirmed that both reducing Mo species and OVs of MoO_3-x surface were responsible for PMS activation. Further experiments and Density Function Theory (DFT) calculation suggest that OVs in MoO_3-x induced the formation of superoxide radical (O₂^•-), and then O₂^•- was transformed into singlet oxygen (¹O₂) or mediated PMS activation to generate radicals, which contritbued to 70.2% of PCB28 degradation. The steady-state concentrations of free radical calculated with the kinetics model show that OVs were more favorable to mediate PMS to generate hydroxyl radicals (^•OH) under oxic conditions, while reducing Mo species would like to induce PMS to produce sulfate radicals (SO₄^•-). Overall, this study is dedicated to a new insight into the in-depth mechanism of PMS activation by OVs-rich catalysts and provides a novel strategy for reactive species regulation in PMS based oxidation process.

FeMo@porous carbon derived from MIL-53(Fe)@MoO3 as excellent heterogeneous electro-Fenton catalyst: Co-catalysis of Mo

An ultra-efficient electro-Fenton catalyst with porous carbon coated Fe-Mo metal (FeMo@PC), was prepared by calcining MIL-53(Fe)@MoO₃. This FeMo@PC-2 exhibited impressive catalytic performance for sulfamethazine (SMT) degradation with a high turnover frequency value (7.89 L/(g·min)), much better than most of reported catalysts. The mineralization current efficiency and electric energy consumption were 83.2% and 0.03 kWh/g_TOC, respectively, at low current (5 mA) and small dosage of catalyst (25.0 mg/L). The removal rate of heterogeneous electro-Fenton (Hetero-EF) process catalyzed by FeMo@PC-2 was 4.58 times that of Fe@PC/Hetero-EF process. Because the internal-micro-electrolysis occurred between PC and Fe⁰, while the co-catalysis of Mo accelerated the rate-limiting step of the Fe³⁺/Fe²⁺ cycle and greatly improved the H₂O₂ utilization efficiency. The results of radical scavenger experiments and electron paramagnetic resonance confirmed the main role of surface-bound hydroxyl radical oxidation. This process was feasible to remove diverse organic contaminants such as phenol, 2,4-dichlorophenoxyacetic acid, carbamazepine and SMT. This paper enlightened the importance of the doped Mo, which could greatly improve the activity of the iron-carbon heterogeneous catalyst derived from metal-organic frameworks in EF process for efficient removal of organic contaminants.

Vanadium as co-catalyst for exceptionally boosted Fenton and Fenton-like oxidation: Vanadium species mediated direct and indirect routes

In this study, vanadium powder (V) was employed as a cocatalyst to enhance the Fenton-like system. The V-Fe(III)/H₂O₂ system can rapidly produce hydroxyl radicals and completely oxidize chloramphenicol with exceptionally high stability for long-term operation. The low-valent vanadium sites on the surface during the stepwise oxidation of vanadium from V⁰ to V(IV) can donate electrons for direct H₂O₂ activation and indirect Fenton reaction by reducing Fe(III) to produce hydroxyl radicals. Meanwhile, density functional theory (DFT) calculation unveils that low-valent vanadium sites of vanadium can lengthen Fe-O bonds of FeOH²⁺ to elevate the oxidation potential of Fe(III) and promote Fe(III) reduction induced by H₂O₂. The self-cleaning effect of vanadium under acidic conditions can maintain reactive sites for sustainable electron donation and long-lasting enhanced Fenton oxidation. This study provides a novel enhanced Fenton oxidation for water remediation and the first mechanistic insights into the origins of V-based advanced oxidation technologies, it may also be beneficial to treat vanadium-contained wastewater.

Critical Review on the Mechanisms of Fe2+ Regeneration in the Electro-Fenton Process: Fundamentals and Boosting Strategies

This review presents an exhaustive overview on the mechanisms of Fe³⁺ cathodic reduction within the context of the electro-Fenton (EF) process. Different strategies developed to improve the reduction rate are discussed, dividing them into two categories that regard the mechanistic feature that is promoted: electron transfer control and mass transport control. Boosting the Fe³⁺ conversion to Fe²⁺ via electron transfer control includes: (i) the formation of a series of active sites in both carbon- and metal-based materials and (ii) the use of other emerging strategies such as single-atom catalysis or confinement effects. Concerning the enhancement of Fe²⁺ regeneration by mass transport control, the main routes involve the application of magnetic fields, pulse electrolysis, interfacial Joule heating effects, and photoirradiation. Finally, challenges are singled out, and future prospects are described. This review aims to clarify the Fe³⁺/Fe²⁺ cycling process in the EF process, eventually providing essential ideas for smart design of highly effective systems for wastewater treatment and valorization at an industrial scale.

Hydrogen peroxide-assisted and histidine-stabilized copper-containing nanozyme for efficient degradation of various organic dyes

Nanozymes have potential applications in many fields, and a novel copper-containing nanozyme with highly dispersity and uniformity was self-assembled for efficient degradation of various organic dyes in this work. In the nanozyme, histidine was used to coordinate with copper ions, and hydrogen peroxide was prone to Fenton-like reaction to generate hydroxylated copper oxide intermediates. The nanozyme showed good peroxidase-like activity, and also had the ability to catalyze the degradation of various organic dyes efficiently with good storage and recycling ability. Furthermore, the degradation kinetics and mechanism of nanozyme had been further studied, and found that hydroxyl radical and singlet oxygen play vital roles in the catalytic degradation process. Meanwhile, this nanozyme can efficiently degrade two organic compounds at the same time, and this system is capable of dealing with complex practical application scenarios where wastewater contains a variety of organic pollutants.

Carbon-doped defect MoS2 co-catalytic Fe3+/peroxymonosulfate process for efficient sulfadiazine degradation: Accelerating Fe3+/Fe2+ cycle and 1O2 dominated oxidation

In order to accelerate Fe3+/Fe2+ cycle and boost singlet oxygen (1O2) generation in peroxymonosulfate (PMS) Fenton-like system, a co-catalyst of defect MoS2 was prepared by C doping and C2-MoS2/Fe3+/PMS system was structured. The removal efficiency of sulfadiazine (SDZ) antibiotics was nearly 100 % in 10 min in the system under the appropriate conditions ([co-catalysts] = 0.2 g/L, [PMS] = 0.1 mM, [Fe3+] = 0.4 mM, pH 3.5), and the reaction rate constant was 4.6 times that of Fe3+/PMS system. C doping MoS2 could induce phase transition, yield more sulfur defects, and expedite electron transfer. Besides, exposed Mo4+ sites on C2-MoS2 could significantly enhance the regeneration and stability of Fe2+ and further promote the activation of PMS. ·OH, SO4·-, and 1O2 were responsible for SDZ degradation in the system. Notably, 1O2 generation was efficiently promoted by sulfur defects and CO sites on C2-MoS2, and 1O2 played the main role in SDZ degradation. Therefore, this co-catalytic system exhibited great anti-interference and stability, and organic contaminants could be efficiently and stably degraded in a 14-day long-term experiment. This work provides a new approach for improving the co-catalytic performance of MoS2 for Fe3+ mediated Fenton-like technology, and offers a promising antibiotic pollutant removal strategy.

Enhanced activation of peroxymonosulfate by a floating FeMo3Ox/C3N4 photocatalyst under visible-light assistance for oxytetracycline degradation: Performance, mechanisms and comparison with H2O2 activation

In this study, a floating FeMo₃O_x/C₃N₄-EP (FM-C-P) composite with highly stability and reusability was synthesized by an impregnation/calcination process and used to activate peroxymonosulfate (PMS) for oxytetracycline (OTC) degradation under visible light irradiation. The results demonstrated that 98.1% of OTC (50 mg/L) removal can be achieved by the activation of PMS (5 mM) using FM-C-P (1 g/L) in 30 min under visible light irradiation. The pseudo-first-order rate constant was calculated to be 0.181 min^-1. The degradation process with PMS was hardly affected by pH (3-11) and co-existing substance. ·SO₄^-, ·OH, ·O₂^- and ¹O₂ were produced in the Vis/PMS/FM-C-P system and ¹O₂ was determined to be the main reactive oxygen species (ROSs). The high efficiency of ROSs production mainly contributed to two mechanisms. Firstly, via the combination of ≡Fe (II)-·SO₅^- and free state ·SO₅^-, ¹O₂ could be generated on the Fe-N_x site. Secondly, photo-induced electrons in the FeMo₃O_x/g-C₃N₄ heterojunction could react with Fe (III) and Mo (VI) to form catalytically active species Fe (II) and Mo (IV). Moreover, the proposed degradation pathway and the toxicity of intermediated products was analyzed. Overall, this study was expected to deepen the understanding of the photo-assisted PMS activation and the generation of ¹O₂ with the presence of metal-oxide/C₃N₄ heterojunction.

Oxygen Vacancy-Mediated Activates Oxygen to Produce Reactive Oxygen Species (ROS) on Ce-Modified Activated Clay for Degradation of Organic Compounds without Hydrogen Peroxide in Strong Acid

The treatment of acid wastewater to remove organic matter in acid wastewater and recycle valuable resources has great significance. However, the classical advanced oxidation process (AOPs), such as the Fenton reaction, encountered a bottleneck under the conditions of strong acid. Herein, making use of the oxidation properties of CeAY (CeO₂@acid clay), we built an AOPs reaction system without H₂O₂ under a strong acid condition that can realize the transformation of organic matter in industrial wastewater. The X-ray photoelectron spectroscopy (XPS) proved that the CeAY based on Ce³⁺ as an active center has abundant oxygen vacancies, which can catalyze O₂ to produce reactive oxygen species (ROS). Based on the electron spin-resonance spectroscopy spectrum and radical trapping experiments, the production of •O₂^- and •OH can be determined, which are the essential factors of the degradation of organic compounds. In the system of pH = 1.0, when 1 mg CeAY is added to 10 mL of wastewater, the degradation efficiency of an aniline solution with a 5 mg/L effluent concentration is 100%, and that of a benzoic acid solution with a 100 mg/L effluent concentration is 50% after 10 min of reaction. This work may provide novel insights into the removal of organic pollutants in a strong acid water matrix.

Revealing the fundamental role of MoO2 in promoting efficient and stable activation of persulfate by iron carbon based catalysts: Efficient Fe2+/Fe3+ cycling to generate reactive species

Electron-rich iron sites are the main sites for iron-based catalysts to activate persulfate (PS) to generate reactive species, while blocked Fe²⁺/Fe³⁺ cycling usually reduces the catalytic performance of iron-based materials and hinders the generation of reactive species in the reaction. To solve the bottleneck, we synthesized an iron-carbon nanocomposite catalyst loaded with MoO₂ (Fe/Mo-CNs). The promotion of MoO₂ on the Fe²⁺/Fe³⁺ cycle in the system allowed Fe/Mo-CNs to exhibit excellent catalytic performance and environmental adaptability. The degradation rate of bisphenol S (BPS) by the Fe/Mo-CNs/PS system was significantly increased to 0.080 min^-1 compared with the iron-carbon based catalyst/persulfate system, and the degradation efficiency of BPS was maintained at around 85% after four cycles. Density functional theory (DFT) calculations showed that the introduction of MoO₂ reduced the reaction energy barrier of persulfate activated by catalysts to produce reactive species, especially promoted the production of more high valent iron (Fe(IV)). Fe(IV) and reactive oxygen species (SO₄·^-, ·OH, ·O₂^- and ¹O₂) worked together on the efficient degradation of BPS. In addition, the test of an automatic circulating degradation plant had proved that Fe/Mo-CNs had a good practical application prospect. BPS was mainly degraded by ring cleavage and O=S=O bond cleavage, and the toxicity of BPS and its intermediates were also evaluated. This work clarifies the mechanism of improving the catalytic performance of heterogeneous iron-based catalysts by MoO₂ in sulfate radical-based advanced oxidation processes (SR-AOPs), providing a new idea for solving the blockage of Fe²⁺/Fe³⁺ cycle in SR-AOPs.

Colorimetric detection of creatinine based on specifically modulating the peroxidase-mimicking activity of Cu-Fenton system

Creatinine (CR) has always been considered as a prime important indicator for evaluating of renal dysfunction. Nevertheless, the literature still lacks in methods that fulfill the requirements for detecting CR effectively. Therefore, the development of a visual sensing method for the detection of CR specifically and sensitively is definitely desirable. To provide a solution, a colorimetric sensing platform for monitoring CR was constructed based on the regulation effect of CR on the peroxidase-mimicking activity of MoO3-Cu2+ system. Here, the prepared MoO3 itself does not have the catalytic activity of peroxidase mimics, but it can be used as a co-catalyst. In the presence of CR, the Cu2+ Fenton-like reaction can be promoted through co-catalysis of MoO3, so as to facilitate the production of more reactive oxygen species (ROS) and accelerate the oxidation process of 3,3',5,5'-tetramethylbenzidine (TMB). As a result, the regulation of MoO3-Cu2+ peroxidase-like activity can be achieved by adding different concentrations of CR. The higher the concentrations of CR, the stronger the catalytic activity for MoO3-Cu2+/CR. Experimental results showed that the colorimetric sensing strategy proposed in this paper can be successfully applied to the analysis of CR in human serum samples.

Activation of peroxymonosulfate by a floating oxygen vacancies - CuFe2O4 photocatalyst under visible light for efficient degradation of sulfamethazine

In this study, expanded perlite supported oxygen vacancies-CuFe₂O₄ (OVs-CFEp) was synthesized via a simple method and utilized as floating catalyst to activate peroxymonosulfate (PMS) for the removal of sulfamethazine (SMT) under visible light irradiation. OVs-CFEp/Vis/PMS synergy presents much superior performance than that of OVs-CFEp/Vis system and OVs-CFEp/PMS system. PMS was efficiently activated by OVs-CFEp at a wide range of pH values, while the degrading rate of SMT was up to 95% in OVs-CFEp/Vis/PMS system. Oxygen vacancies and ·O₂^- accelerated the conversion of Fe(III)/Fe(II) and Cu(I)/Cu(II). The combination of the floating loader boosted light absorption capacity and sufficiently prevented metal ions leaching, which was all beneficial to enhance catalytic performance and recyclability. Besides, the reactive oxygen species were investigated systematically, proving that visible light and OVs-CFEp could activate PMS to produce ·SO₄^-, ·OH, O₂·^-, and ¹O₂ reactive species. Furthermore, based on intermediates identification and Density Functional Theory (DFT) calculation, three types and seven main degradation pathways involving cleavage of bond, SMT molecular rearrangement, and hydroxylation reaction were proposed. So this high photo-absorbing catalyst coupling with advanced oxidation progress was promising for extensive environmental remediation.

Efficient utilization of the electron energy of antibiotics to accelerate Fe(III)/Fe(II) cycle in heterogeneous Fenton reaction induced by bamboo biochar/schwertmannite

The discharge of antibiotics evokes environmental health crisis, and is also a waste of organic energy. Currently, heterogeneous Fenton for antibiotics removal has attracted growing attentions due to wide pH range and no iron sludge production, however, it often suffers from a low formation rate of Fe(II), resulting in difficult application of heterogeneous Fenton technology in sewage treatment. To overcome this drawback, bamboo biochar (BB) is coupled with schwertmannite (Sch) through Acidithiobacillus ferrooxidans-mediated Fe(II) oxidation reaction to obtain a heterogeneous catalyst (Sch/BB) with high adsorption performance and Fenton activity. According to the analysis of experimental results, electrons around C (from BB) can easily transfer to Fe by Fe-O-C bonds to expedite ≡Fe(III)/≡Fe(II) cycle, while electrons of antibiotics adsorbed on Sch/BB surface are effectively utilized to maintain the efficient regeneration of ≡Fe(II) through BB electron shuttle or Fe-O-C bonds between Sch/BB and pollutants, further causing a superior Fenton activity (98% antibiotics removal) of Sch/BB. Moreover, due to its excellent adsorption performance, Sch/BB as filter materials can effectively remove dye pollutants in flow wastewater. These findings provided a high-activity and practical heterogeneous Fenton catalyst for pollutants degradation, while a new perspective for efficient utilization of the electrons of organic pollutants was given.

Enhanced visible light photo-Fenton-like degradation of tetracyclines by expanded perlite supported FeMo3Ox/g-C3N4 floating Z-scheme catalyst

In the conventional Fenton system, the relatively low efficiency of Fe (II) regeneration is a significant drawback. To address this shortcoming, a novel floating Z-scheme photo-Fenton catalyst FeMo₃O_x/g-C₃N₄/EP was prepared by a facile dip-calcination method, in which iron and molybdenum oxides with mixed valence states (FeMo₃O_x) and graphitic carbon nitride (g-C₃N₄) were loaded on the expanded perlite. The removal efficiencies reached the maximum at 98.0%, 93.1% and 97.1% for tetracycline, oxytetracycline and chlortetracycline, respectively, after 60 min dark adsorption and 60 min photo-Fenton process. The aid of dual ion (Fe and Mo) synergy system and photoreduction by Z-scheme photocatalyst enhanced the Fe (II) regeneration, resulting in the excellent performance. Radical scavenger experiment, electron spin resonance spectra (ESR) and X-ray photoelectron spectra (XPS) were used to confirm the mechanism of free radicals' formation and Fe/Mo redox cycling. ·OH, ·O₂^- and ¹O₂ played important roles in the pollutant's degradation, while the generation of ·O₂^- was enhanced due to the floatability in this system. The possible degradation pathways of TC were put forward according to the results of mass spectrum and Orbital-Weighted Fukui Function. Overall, this work provides new insights on the cooperation between iron-based mix oxides and semiconductor in the photo-Fenton system.

The construction of a palladium–hydrogen accelerated catalytic Fenton system enhanced by UiO-66(Zr)

The introduction of H2 and Pd/UiO-66(Zr) accelerated the FeII/FeIII cycle and led to higher contaminant degradation using only a trace level of FeII in several reaction cycles.

Visible light photodegradation of organic dyes using electrochemically synthesized MoO3/ZnO

In this study, flake-like MoO₃-ZnO composite was prepared using a simple and robust electrochemical setup. The composite was characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, elemental analysis, X-ray photoelectron spectroscopy, thermogravimetric analysis, photoluminescence, zeta potential analysis, and electrochemical impedance study. The modified ZnO shows a remarkable catalytic activity towards the photodegradation of three potentially hazardous dyes, malachite green, crystal violet, and methylene blue. More than 95% of both malachite green and crystal violet degraded within 140 min under visible light irradiation. Scavenger studies reveal that OH· radicals produced by the photo-separated charges on MoO₃-ZnO are responsible for the degradation of all three dyes. The photoactive charge carriers show less recombination rate as evidenced by the photoluminescence spectrum due to the interparticle charge migration process. This work suggests a new versatile procedure for the synthesis of MoO₃-ZnO composites and establishes its photocatalytic efficacy under visible light with three common pollutant dyes found in wastewater.

Robust Cr(VI) reduction over hydroxyl modified UiO-66 photocatalyst constructed from mixed ligands: Performances and mechanism insight with or without tartaric acid

Hydroxyl modified UiO-66 ((OH)₂-UiO-66-X%, X represents the mass content ratio of introduced 2,5-dihydroxyterephthalic acid) was prepared via a solvothermal reaction between zirconium tetrachloride, benzene-1,4-dicarboxylic acid (H₂BDC), as well as 2,5-dihydroxyterephthalic acid (H₂BDC-(OH)₂). It was found that hydroxyl groups can act as the intramolecular hole scavenger to boost the photo-induced charge carrier separation to enhance Cr(VI) reduction. The photocatalytic Cr(VI) reduction activities of (OH)₂-UiO-66-X% were investigated upon the irradiation of low-power ultraviolet LED light. The findings demonstrated that (OH)₂-UiO-66-20% with good cyclicity and stability exhibited superior photocatalytic performances to both UiO-66 and (OH)₂-UiO-66. The introduction of hydroxyl groups can also extend the light absorption region to longer wavelength in visible range, which provides possibility for displaying photocatalytic activities under sunlight. The effect of small molecule organic acid (SOAs), pH value, and co-existing inorganic ions on photocatalytic performances of (OH)₂-UiO-66-20% were investigated. Tartaric acid (TA) as typical SOAs was introduced to the reaction system to further boost the photocatalytic Cr(VI) reduction via acting as hole scavenger, constructing charge-transfer-complex for quick electron transportation, and producing COO·^- radicals. This work opened a new opportunity for modified MOFs for boosted elimination activities for environmental pollutants.