A review on adsorbents for treatment of water and wastewaters containing copper ions

Fabrication of nitrogen-doped carbon dots biomass composite hydrogel for adsorption of Cu (II) in wastewater or soil and DFT simulation for adsorption mechanism

With the increase of Cu (II) content, its bioaccumulation becomes a potential pollution to the environment. It is necessary to design an economical and efficient material to remove Cu (II) without causing other environmental hazards. A novel material of alginate composite bead (ALG@NCDs) was synthesized by embedding N-doped carbon dots into pure alginate bead for the adsorption of Cu (II) from wastewater and contaminated soil. The initial concentration, the amount of adsorbent, temperature, adsorption time, and pH value were optimized for the adsorption of Cu (II). According to the Langmuir isothermal adsorption model, the maximum adsorption amount of the material to Cu (II) was 152.44 mg/g. The results of selective adsorption showed that ALG@NCDs had higher affinity to Cu (II) than to Pb (II), Co (II), Ni (II), and Zn (II). After five adsorption-desorption experiment, adsorption capacity of the ALG@NCDs was kept 89% of the initial adsorption capacity. Its Cu (II) adsorption mechanism was studied by density functional theory calculations. In addition, the material could effectively adsorb Cu (II) and release the phytonutrient Ca (II) simultaneously when applied to actual wastewater and soil. The fabricated ALG@NCDs would be a promising material for the adsorption of Cu (II) from wastewater or soil.

Determination of copper in rose tea samples using flame atomic absorption spectrometry after emulsification liquid-liquid microextraction

Rose tea infusion has gained popularity worldwide due to its health benefits. However, it is known that tea plants can be contaminated with heavy metals including copper. Hence, an accurate and applicable analytical method namely emulsification liquid-liquid microextraction based deep eutectic solvent - flame atomic absorption spectrometry (ELLME-DES-FAAS) was proposed to determine copper at trace levels in rose tea samples. Under the optimum experimental conditions, analytical figures of merit for the developed method were examined, and dynamic range, limit of detection (LOD) and limit of quantification (LOQ) were found to be 5.07-246.61 µg/kg (mass-based) with 0.9992 coefficient of determination, 2.50 µg/kg and 8.32 µg/kg, respectively. A matrix matching calibration strategy was employed to boost recovery results, and the acceptable recovery results were recorded between 95.9 % and 118.4 %. According to recovery results, the developed analytical method can be safely employed to determine the concentration of copper in rose tea samples accurately.

Recent breakthroughs on the development of electrodeionization systems for toxic pollutants removal from water environment

Since ecosystems are becoming inherently polluted, long-term contaminant removal methods are required. Electrodeionization, in particular, has recently been demonstrated as an effective approach for eliminating ionic compounds from contaminated water sources. Being a more environmentally friendly technology is most likely the main reason for its eminence. It uses electricity to replace toxic contaminants that are conventionally used to regenerate and hence reducing the toxins associated with resin regeneration. In wastewater treatment, continuous electrodeionization system overcomes several limitations of ion exchange resins, notably ion dumping. This prospective assessment delves into the mechanism, principle, and theory of electrodeionization system. It also focused on the design and applications, particularly in the removal of toxic compounds, as well as current advances in the electrodeionization system. Recent breakthroughs in electrodeionization were comprehensively discussed. Further developments in electrodeionization systems are also projected, with improved efficiency at the time of functioning at lower costs because of reduced energy use, proving them desirable for commercial usage with a broad array of applications across the globe.

Carboxyl and polyamine groups functionalized polyacrylonitrile fibers for efficient recovery of copper ions from solution

Heavy metals (e.g., Cu) in wastewater are attractive resources for diverse applications, and adsorption is a promising route to recovery of heavy metals from wastewater. However, high-performance adsorbents with high adsorption capacity, speed, and stability remain challenging. Herein, chelating fibers were prepared by chemically grafting amine and carboxyl groups onto the polyacrylonitrile fiber surface and used in the wastewater's adsorption of Cu2+. The adsorption behavior of Cu2+ on the fibers was systematically investigated, and the post-adsorption fibers were comprehensively characterized to uncover the adsorption mechanism. The results show that chelated fiber has a 136.3 mg/g maximum capacity for Cu2+ adsorption at pH = 5, and the whole adsorption process could reach equilibrium in about 60 min. The adsorption process corresponds to the quasi-secondary kinetic and Langmuir models. The results of adsorption, FTIR, and XPS tests indicate that the synergistic coordination of -COOH and -NH2 plays a leading role in the rapid capture of Cu2+. In addition, introducing hydrophilic groups facilitates the rapid contact and interaction of the fibers with Cu2+ in the solution. After being used five times, the fiber's adsorption capacity remains at over 90% of its original level.

A cohesive effort to assess the suitability and disparity of carbon nanotubes for water treatment

Population growth, industrialization, and the extensive use of chemicals in daily life have all contributed to an increase in waste generation and an intensified release of organic pollutants into the aquatic environment. To ensure the quality of water (including natural resources), the removal of these pollutants from wastewater has become a challenging task for scientific community. Conventional physical, chemical, and biological treatment methods are commonly used in combinations and are not very effective. Recently, carbon nanotubes (CNTs) emerged as the most reliable and adaptable choice for efficient water treatment due to their extraordinary material properties appearing as a single-step solution for water treatment. High surface area, exceptional porosities, hollow and layered structures, and ease of chemical activation and functionalization are some properties which makes it excellent adsorption material. Hence, this review paper discusses the recent advances in the synthesis, purification, and functionalization of CNTs for water and wastewater treatment. In addition, this study also also provides a quick overview of CNTs-based advance technologies employed in water treatment and carefully assesses the benefits versus risks during large-scale water treatment. Furthermore, it concludes that identified risks to the environment and human health cannot be easily ignored and strict regulatory requirements are a must for producing low-cost innoxious CNTs.

PVDF/Clay Spheres Obtained through Phase Inversion for Cu Ion Removal

In this study, spheres of poly (vinylidene fluoride)/clay were synthesized using an easy dripping method (also known as phase inversion). The spheres were characterized by scanning electron microscopy, X-ray diffraction, and thermal analysis. Finally, application tests were carried out using commercial cachaça, a popular alcoholic beverage in Brazil. The SEM images revealed that during the solvent exchange process for sphere formation, PVDF tends to form a three-layered structure with a low-porosity intermediate layer. However, the inclusion of clay was observed to reduce this layer and also widen the pores in the surface layer. The results of the batch adsorption tests showed that the composite with 30% clay content in relation to the mass of PVDF was the most effective among those tested, with the removal of 32.4% and 46.8% of the total copper present in the aqueous and ethanolic media, respectively. The adsorption of copper from cachaça in columns containing cut spheres resulted in adsorption indexes above 50% for samples with different copper concentrations. Such removal indices fit the samples within the current Brazilian legislation. Adsorption isotherm tests indicate that the data fit better to the BET model.

Reliability of stored river water as an alternative for consumption in Ekpoma, Nigeria: a human health risk assessment

With looming global water-related issues, the monitoring of water quality for household and industrial consumption has become more pertinent. Rivers in nearby towns serve as primary water sources for Ekpoma town. 123 samples of stored river water were collected from 41 sampling locations and physical properties - pH, electrical conductivity (EC), salinity, temperature, and total dissolved solids (TDS) - were measured in situ using the Hanna edge® Multiparameter EC/TDS/Salinity Meter-HI2030. Atomic absorption spectrophotometry (AAS) was used to detect and measure the concentration of potentially toxic metals (PTMs): Al, Cr, Cu, Fe, Mn, Ni, Pb, and Zn. The measured concentrations were compared to the WHO, US EPA, and NSDWQ regulatory standards, and a spatiotemporal health risk analysis was performed using HERisk software. Twenty-five percent of the tested samples contained PTM concentrations within the allowable regulatory limits. Spatiotemporal health risk analysis showed that 98.8% of the cumulative carcinogenic risks (CRcum) were entirely from Pb contamination via oral ingestion. PTM concentrations in the samples suggest the degradation of river water quality due to agricultural activities, crude oil exploration activities, and soil composition in the region. Best management practices (BMPs) and treatment processes for the removal of detected contaminants are recommended to improve water quality.

Forecasting contamination in an ecosystem based on a network model

This paper aims to predict heavy metal pollution based on ecological factors with a new approach, using artificial neural networks (ANNs), by significantly removing typical obstacles like time-consuming laboratory procedures and high implementation costs. Pollution prediction is crucial for the safety of all living things, for sustainable development, and for policymakers to make the right decisions. This study focuses on predicting heavy metal contamination in an ecosystem at a significantly lower cost because pollution assessment still primarily relies on conventional methods, which are recognized to have disadvantages. To accomplish this, the data collected for 800 plant and soil materials have been utilized in the production of an ANN. This research is the first to use an ANN to predict pollution very accurately and has found the network models to be very suitable systemic tools for modelling in pollution data analysis. The findings appear are promising to be very illuminating and pioneering for scientists, conservationists, and governments to swiftly and optimally develop their appropriate work programs to leave a functioning ecosystem for all living things. It has been observed that the relative errors calculated for each of the polluting heavy metals for training, testing, and holdout data are significantly low.

Removal of Cd(II), Co(II), Cr(III), Ni(II), Pb(II) and Zn(II) ions from wastewater using polyethyleneimine (PEI) cryogels

The removal of the target analytes, Cd(II), Co(II), Cr(III), Ni(II), Pb(II), and Zn(II) from contaminated waters was achieved using super porous polyethyleneimine (PEI) cryogels as adsorbent. The optimum values of the sample pH and contact time were determined as 4.0 and 90 min, respectively, for the removal of the analytes. The adsorption capacities of the sorbent were between 19.88 and 24.39 mgg^-1 from 10 mL of 50 mgL^-1 target metal ion solutions. The sorption kinetics of metal ions were fitted with the pseudo-second-order model. The adsorption isotherms of the target analytes into PEI cryogel were well-fitted to the Langmuir isotherm model as expected from the material homogeneity. The selectivity of the PEI cryogel in the presence of Na⁺, Ca²⁺, Mg²⁺, NO₃^-, K⁺ and Cl^- ions even at high concentrations was tested, and the tolerance limits were satisfactory enough, e.g., the adsorption of the target analytes was even not affected in the presence of 2000 mgL^-1 Ca²⁺, K⁺, Na⁺, Cl^- and 5000 mgL^-1 NO₃^- ions. The PEI cryogels were successfully utilized in different industrial wastewater samples that were spiked with a known amount of analytes. The removal of the analytes from wastewater samples was in the following ranges 91.94-99.86% for Cd(II), 89.59-99.89% for Co(II), 80.35-99.76% for Cr(III), 92.02-99.84% for Ni(II), 83.28-99.86% for Pb(II), and 82.94-98.24% for Zn(II), respectively. The presented novel removal strategy offers a selective, efficient, and easy application for target metal ions from industrial wastewater samples.

Advancements in Clay Materials for Trace Level Determination and Remediation of Phenols from Wastewater: A Review

The wide spread of phenols and their toxicity in the environment pose a severe threat to the existence and sustainability of living organisms. Rapid detection of these pollutants in wastewaters has attracted the attention of researchers from various fields of environmental science and engineering. Discoveries regarding materials and method developments are deemed necessary for the effective detection and remediation of wastewater. Although various advanced materials such as organic and inorganic materials have been developed, secondary pollution due to material leaching has become a major concern. Therefore, a natural-based material is preferable. Clay is one of the potential natural-based sorbents for the detection and remediation of phenols. It has a high porosity and polarity, good mechanical strength, moisture resistance, chemical and thermal stability, and cation exchange capacity, which will benefit the detection and adsorptive removal of phenols. Several attempts have been made to improve the capabilities of natural clay as sorbent. This manuscript will discuss the potential of clays as sorbents for the remediation of phenols. The activation, modification, and application of clays have been discussed. The achievements, challenges, and concluding remarks were provided.

Rapid growth of MXene-based membranes for sustainable environmental pollution remediation

Water consumption has grown in recent years due to rising urbanization and industry. As a result, global water stocks are steadily depleting. As a result, it is critical to seek strategies for removing harmful elements from wastewater once it has been cleaned. In recent years, many studies have been conducted to develop new materials and innovative pathways for water purification and environmental remediation. Due to low energy consumption, low operating cost, and integrated facilities, membrane separation has gained significant attention as a potential technique for water treatment. In these directions, MXene which is the advanced 2D material has been explored and many applications were reported. However, research on MXene-based membranes is still in its early stages and reported applications are scatter. This review provides a broad overview of MXenes and their perspectives, including their synthesis, surface chemistry, interlayer tuning, membrane construction, and uses for water purification. Application of MXene based membrane for extracting pollutants such as heavy metals, organic contaminants, and radionuclides from the aqueous water bodies were briefly discussed. Furthermore, the performance of MXene-based separation membranes is compared to that of other nano-based membranes, and outcomes are very promising. In order to shed more light on the advancement of MXene-based membranes and their operational separation applications, significant advances in the fabrication of MXene-based membranes is also encapsulated. Finally, future prospects of MXene-based materials for diverse applications were discussed.

Utilisation of waste Cu-, Mn- and Fe-loaded zeolites generated after wastewater treatment as catalysts for air treatment

Disposal of copper, manganese and iron is particularly problematic in wastewater of metallurgical and galvanization plants, the electronics industry and agriculture. On the other hand, volatile organic compounds (VOCs), emitted from industrial processes, transportation and consumer products are the main class of air pollutants. The study revealed the potential of waste metal-loaded zeolite, generated through wastewater treatment procedures, to be utilised as an effective VOC removal catalyst for air treatment. In the first step, we have evaluated the sorption performance of natural zeolite clinoptilolite (HEU type), and synthetic zeolite 4A (LTA type) for the simultaneous removal of Cu2+, Mn2+ and Fe3+ species from aqueous solution. By a detailed sorption study, we determined the optimum sorption conditions and maximum metal concentrations in wastewater that can be after treatment disposed of in rivers or municipal plants. The efficiency of both zeolites for metal immobilization was demonstrated for concentrations up to 5 mg metals/1 g zeolite. These waste Cu-, Mn- and Fe-loaded zeolites were thermally treated at 540 °C before the second step, where we evaluated their catalytic performance in removing VOC. The thermally treated waste Cu-, Mn- and Fe-loaded natural zeolite clinoptilolite showed good catalytic performance in total toluene oxidation as a model VOC (conversion rate up to 96% at 510°C) and cycling stability (less than 15% drop in conversion rate in 4 h). In contrast, this is not the case for thermally treated waste Cu-, Mn- and Fe-loaded synthetic zeolite 4A.

Modification of silica nanoparticles by 2,4-dihydroxybenzaldehyde and 5-bromosalicylaldehyde as new nanocomposites for efficient removal and preconcentration of Cu(ii) and Cd(ii) ions from water, blood, and fish muscles

Herein, silica nanoparticles were modified by 2,4-dihydroxybenzaldehyde and 5-bromosalicylaldehyde to produce new nanocomposites which were abbreviated as N₁ and N₂, respectively. The synthesized nanocomposites were used for efficient removal and preconcentration of Cu(ii) and Cd(ii) ions from water, blood, and fish muscles. FE-SEM, FT-IR, XRD, CHN elemental analysis, and nitrogen gas sorption analyzer were used to characterize the new nanocomposites. The XRD proved that the synthesized oxide is cristobalite with an average crystallite size of 54.80 nm. Due to the formation of the C Created by potrace 1.16, written by Peter Selinger 2001-2019 ]]> N group, the intensity of the XRD peak at 2θ = 21.9° in the N₁ and N₂ nanocomposites decreased significantly. The FT-IR bands, which appeared at 1603 and 1629 cm⁻¹ in the N₁ and N₂ nanocomposites, are attributable to the bending vibration of CN and/or OH, respectively. Also, the FE-SEM analysis shows the morphology of the silica nanoparticles which were identified as spherical and rod-like with slight agglomeration while the N₁ and N₂ nanocomposites have flaky surfaces due to the formation of CN groups. The maximum Cu(ii) ion adsorption capacities of the N₁ and N₂ nanocomposites are 64.81 and 40.93 mg g⁻¹, respectively. The maximum Cd(ii) ion adsorption capacities of the N₁ and N₂ nanocomposites are 27.39 and 26.34 mg g⁻¹, respectively. The adsorption of Cu(ii) or Cd(ii) ions using the synthesized nanocomposites is spontaneous, chemical, exothermic, and well-matched with the Langmuir equilibrium isotherm. The recovery findings demonstrate that the preconcentration process is accurate, adaptable, and resulted in quantitative separation because % Recovery is more than 95%. Furthermore, the % RSD was less than 3.5%, indicating good reproducibility.

Herein, silica nanoparticles were modified by 2,4-dihydroxybenzaldehyde and 5-bromosalicylaldehyde to produce new nanocomposites which were abbreviated as N₁ and N₂, respectively.

Application of Cement Paste in Mining Works, Environmental Protection, and the Sustainable Development Goals in the Mining Industry

Cement paste is an already well-known material used in ore mining. It is mainly used to fill excavation areas and the tailings from the surface return to underground mines. In this way, the amount of deposited material and degradation of the surface of the terrain are reduced. The paste itself can be used as an artificial barrier between mining works and underground watercourses. Significant economic and environmental benefits can be expected from using cement paste, which would contribute to sustainable development. The basic materials that make up cemented paste backfill (CPB) are flotation tailings, cement, and water. For CPB to be adequately and safely applied to the filling of excavation spaces and indirectly to the protection of the groundwater, environment, and sustainable development of the mining industry, it must meet certain physical–mechanical, physicochemical, and deformation properties. This paper presents the results of synthesized and analyzed samples of different compositions based on flotation tailings (from the production of ZiJin Copper in Bor, Serbia), cement, and water. The methods used for chemical and mineralogical tests include inductively coupled plasma atomic emission spectroscopy (ICP-AES), atomic absorption spectroscopy (AAS), X-ray diffraction analysis (XRD), and nephelometric turbidity units (NTUs; turbidimetry). The results prepared with CPB consisting of 5% cement, 24% water, and 71% flotation tailings were the most acceptable.

Functionalization of MXene-based nanomaterials for the treatment of micropollutants in aquatic system: A review

The increased industrialization and urbanization generate a larger quantity of effluent that is discharged into the environment regularly. Based on the effluent composition produced from various industries, the number of hazardous substances such as heavy metals, hydrocarbons, volatile organic compounds, organic chemicals, microorganisms introduced into the aquatic systems vary. The conventional wastewater treatment systems do not meet the effluent standards before discharge and require a different treatment system before reuse. Adsorption is an eco-friendly technique that uses selective adsorbents to remove hazardous pollutants even at microscale levels. MXene, a 2-Dimensional nanomaterial with resplendent properties like conductivity, hydrophilicity, stability, and functionalized surface characteristics, is found as a potential candidate for pollutant removal systems. This review discusses the fabrication, characterization, and application of MXene based nanoparticles to remove many pollutants in water treatment systems. The improvement in surface properties and adsorption capacity of MXene based NPs, when modified using different modification agents, has also been discussed. Their feasibility in terms of economic and environmental aspects has been evaluated to understand their scope for practical application in large-scale industries. The challenges towards the synthesis and toxicity's importance have been discussed, with the appropriate recommendations.

A critical overview of MXenes adsorption behavior toward heavy metals

In recent years, tremendous interest has been generated in MXenes as a fast-growing and diversified family of two-dimensional (2D) materials with a wide range of potential uses. MXenes exhibit many unique structural and physicochemical properties that make them particularly attractive as adsorbents for removing heavy metals from aqueous media, including a large surface area, abundant surface terminations, electron-richness, and hydrophilic nature. In light of the adsorption capabilities of MXenes at the ever-increasing rate of expansion, this review investigates the recent computational predictions for the adsorption capabilities of MXenes and the effect of synthesis of different MXene on their remediation behavior toward heavy metals. The influence of MXene engineering strategies such as alkalization, acidification, and incorporation into organic and inorganic hosts on their surface properties and adsorption capacity is compared to provide critical insights for designing effective MXene adsorbents. Additionally, the review discusses MXenes' adsorption mechanisms, the effect of coexisting ions on MXenes' selectivity, the regeneration of exhausted MXenes, and provides an overview of MXenes' stability and biocompatibility to demonstrate their potentiality for wastewater remediation. Finally, the review identifies current flaws and offers recommendations for further research.

Thy-AuNP-AgNP Hybrid Systems for Colorimetric Determination of Copper (II) Ions Using UV-Vis Spectroscopy and Smartphone-Based Detection

A colorimetric probe based on a hybrid sensing system of gold nanoparticles (AuNPs), silver nanoparticles (AgNPs), and thymine (Thy) was developed for easy and rapid detection of copper (II) ions (Cu2+) in solution. The underlying principle of this probe was the Cu2+-triggered aggregation of the nanoparticle components. Color change of the sensing solution (from red to purple) was clearly observed with naked eyes. The experimental parameters, including pH and concentration of tris buffer, thymine concentration and AgNP dilution ratios, were investigated and optimized. Once optimized, the limits of detection were found to be 1, 0.09 and 0.03 ppm for naked eyes, smartphone application and UV-vis spectrophotometer, respectively. Furthermore, determination of Cu2+ was accomplished within 15 min under ambient conditions. For quantitative analysis, the linearity of detection was observed through ranges of 0.09−0.5 and 0.03−0.5 ppm using smartphone application and UV-vis spectrophotometer, respectively, conforming to the World Health Organization guideline for detection of copper at concentrations < 2 ppm in water. This developed hybrid colorimetric probe exhibited preferential selectivity toward Cu2+, even when assessed in the presence of other metal ions (Al3+, Ca2+, Pb2+, Mn2+, Mg2+, Zn2+, Fe3+, Ni2+, Co2+, Hg2+ and Cd2+). The developed procedure was also successfully applied to quantification of Cu2+ in real water samples. The recovery and relative standard deviation (RSD) values from real water sample analysis were in the ranges of 70.14−103.59 and 3.21−17.63%, respectively. Our findings demonstrated a successful development and implementation of the Thy-AuNP-AgNP hybrid sensing system for rapid, simple and portable Cu2+ detection in water samples using a spectrophotometer or a smartphone-based device.

Removal of Copper(II) in the Presence of Sodium Dodecylobenzene Sulfonate from Acidic Effluents Using Adsorption on Ion Exchangers and Micellar-Enhanced Ultrafiltration Methods

The selective removal of Cu(II) in the presence of sodium dodecylobenzene sulfonate from acidic effluents was made using the adsorption and micellar-enhanced ultrafiltration methods. Lewatit MonoPlus TP220 showed the best adsorption behavior in the systems containing Cu(II) in the presence of ABSNa50 surfactant compared to the other adsorbents (removal efficiency ≈ 100%, sorption capacity ≈ 10 mg/g). The kinetics followed the pseudo-second order kinetic equation. The Langmuir adsorption capacities were 110 mg/g (the system with ABSNa50 above CMC) and 130.38 mg/g (the system with ABSNa50 below CMC). The working ion exchange capacities were Cw = 0.0216 g/mL and Cw = 0.0135 g/mL. The copper removal by the micellar-enhanced ultrafiltration method was 76.46% (0.1 mol/L HCl).

Adsorption of Cetylpyridinium Chloride at Silica Nanoparticle/Water Interfaces (II): Dependence of Surface Aggregation on Particle Size

Herein, we report a thermodynamic model that relates the adsorption (aggregation) parameters of surfactants at solid/liquid interfaces to particle radius (r). The adsorption (aggregation) parameters include adsorption amounts, equilibrium constants (or the standard Gibbs free energy changes), the critical surface micelle concentration (csmc), and the average aggregation number of surface micelles (n). The model predicts the size dependence of the surface aggregation of surfactants, which is determined by the changes in the interfacial tension and the molar volume of surface components caused by adsorption. In addition, the adsorption of cetylpyridinium chloride (CPyCl), a cationic surfactant, on silica nanoparticles with different r values (ca. 6-61 nm) was determined at 298 K and pH 4, showing an obvious size dependence, consistent with the prediction of the model. With an increase in r, the adsorption isotherm changes from the double-plateau type to the Langmuir type, accompanied by obvious changes in the adsorption parameters. The size-dependent adsorption data can be well described using the model equations, indicating that the model presented here is acceptable. In addition, the model can extract information on the interfacial tensions from adsorption data. We think that the model deepens the understanding of the aggregation phenomena of surfactants at solid/liquid interfaces.

MXenes as emerging nanomaterials in water purification and environmental remediation

Environmental pollution has accelerated and intensified because of the acceleration of industrialization, therefore fabricating excellent materials to remove hazardous pollutants has become inevitable. MXenes as emerging transition metal nitrides, carbides or carbonitrides with high conductivity, hydrophilicity, excellent structural stability, and versatile surface chemistry, become ideal candidates for water purification and environmental remediation. Particularly, MXenes reveal excellent sorption capability and efficient reduction performance for various contaminants of wastewater. In this regard, a comprehensive understanding of the removal behaviors of MXene-based nanomaterials is necessary to explain how they remove various pollutants in water. The eliminate process of MXene-based nanomaterials is collectively influenced by the physicochemical properties of the materials themselves and the chemical properties of different contaminants. Therefore, in this review paper, the synthesis strategies and properties of MXene-based nanomaterials are briefly introduced. Then, the chemical properties, removal behaviors and interaction mechanisms of heavy metal ions, radionuclides, and organic pollutants by MXene-based nanomaterials are highlighted. The overview also emphasizes associated toxicity, secondary contamination, the challenges, and prospects of the MXene-based nanomaterials in the applications of water treatment. This review can supply valuable ideas for fabricating versatile MXene nanomaterials in eliminating water pollution.

Sustainable approaches for nickel removal from wastewater using bacterial biomass and nanocomposite adsorbents: A review

In this article, the nickel (Ni²⁺) ions removal from the wastewater is reviewed. Adsorption is widely used to remove Ni²⁺ ions from waters and wastewaters. The usage of biomass is becoming more common for Ni²⁺ ions removal, while the commercial activated carbon from different agriculture wastes is preferred as an adsorbent for Ni²⁺ ion removal. The present review aimed to organise the available information regarding sustainable approaches for Ni²⁺ ions removal from water and wastewaters. These include adsorption by nanoparticles, bacterial biomass, and activated carbon from agriculture wastes, since they are the most common used for the Ni²⁺ ions removal. The bacterial and agricultural waste adsorbents exhibited high efficiency with a renewable source of biomass for Ni²⁺ ion removal. The biosorption capacity of the Ni²⁺ ions by the bacterial biomass range from 5.7 to 556 mg/g, while ranging from 5.8 to 150 mg/g by the activated carbon from different organic materials. The biosorption capacity of the nanocomposite adsorbents might reach to 400 mg/g. It appeared that the elimination of nickel ions need a selective biomass adsorbent such as the tolerant bacterial cells biomass which acts as a store for Ni²⁺ ion accumulations as a results for the active and passive transportation of the Ni²⁺ ions through the bacterial cell membrane.

Nanocell hybrids for green chemistry

Global concerns about reducing or minimizing the costs associated with toxic waste materials have driven the continuing development of green-cell-based biosynthesis methods. Inspired by the hybridization phenomenon of living organisms, recent interest has arisen in nanocell hybrids that possess multiple new functions. They have potential to propel biosynthesis into a new generation of green chemistry. This review article discusses the development of applications for nanocell hybrids in the areas of sustainable energy, clean environment, and green catalysis. Continuing advances in these hybrids will require combining knowledge from the fields of biology, physics, chemistry, material science, and engineering.

A Model for the Structure of Adsorbed Layers at Solid/Liquid Interfaces

Understanding the structure of adsorbed layers, including their composition (the mole fraction of sorbate, x_A) and thickness (d_al), is of great significance for revealing the nature of adsorption and guiding its applications. Many techniques have been used to estimate the structure of adsorbed layers of organics at solid/liquid interfaces. However, there is still a lack of feasible thermodynamic models to describe the correlation between the structure (more precisely, x_A and d_al) and the equilibrium adsorption amount (Γ_e). Herein, a thermodynamic model, called the dynamic bonding equilibrium (DBE) model, was developed on the basis of the adsorption equilibrium thermodynamics with an assumption that, at adsorption equilibrium, the sorbate and solvent within the adsorbed layer both exist in different bonding states. The DBE model relates x_A and d_al with Γ_e and thus can predict or describe the structure (x_A and d_al) of adsorbed layers from Γ_e. Its rationale was confirmed by the literature-reported adsorption data of organics, including surfactants, proteins, and polymers, on hydrophilic and hydrophobic surfaces in water. This work provides a feasible approach for obtaining information about the structure of adsorbed layers at solid/liquid interfaces.

A new and efficient diaminopyrimidine-based colorimetric and fluorescence chemosensor for the highly selective and sensitive detection of Cu2+ in aqueous media and living cells

In this paper, a new and effective diaminopyrimidine-based chemosensor (DAPCS) was developed for the highly selective and ultra-sensitive detection of Cu²⁺ ion in aqueous media and living cell. Characterization and structure determining of DAPCS was determined by UV-Vis, FTIR and NMR analyses. It is observed that DAPCS and Cu (II) forms a ligand to metal charge transfer (LMCT) complex which produces distinguishable red color. The results also indicate that the DAPCS easily interacts with Cu²⁺ ion to form a 1:1 stoichiometry complex (DAPCS -Cu²⁺), resulting in a bathochromic shift in absorption maximum (429 nm to 449 nm) and remarkable quenching fluorescence intensity at the wavelength of 501 nm in DMSO-H₂O solution. Furthermore, the detection limit of DAPCS towards Cu²⁺ was calculated to be 3.19 µM. Meanwhile, DAPCS was applied as fluorescent probe for detection of Cu²⁺ ions with the detection limit of 0.014 µM. The optimal pH range of probe DAPCS for quantitative analysis of Cu²⁺ ions was 9-11, which renders it suitable for detection of Cu²⁺ under physiological conditions. Additionally, the DAPCS could be applied to detect Cu²⁺ in real water samples and in HeLa cells, indicating the practical uses of DAPCS in real analyses.

A clean process for selective recovery of copper from industrial wastewater by extraction-precipitation with p-tert-octyl phenoxy acetic acid

A novel method for the selective removal and recovery of copper ion from copper-containing wastewater by extraction-precipitation with p-tert-octyl phenoxy acetic acid as a precipitant is presented. The morphology, thermal stability and solubility of POAA were synthesized and characterized. Then the application of POAA to precipitate copper from simulated copper-containing wastewater was studied. The effects of some factors (i.e., time, pH, temperature, dosage of precipitant) on copper precipitation efficiency (P%) and water solubility of POAA were discussed. The extraction-precipitation mechanism of POAA and Cu²⁺ was investigated by slope analysis combined with SEM, EDS, XPS and IR spectra. The concentration and purity of copper from industrial wastewater increased from 100.2 mg/L to 27,916 mg/L and 13.71%-93.01% respectively, treating by the proposed extraction-precipitation. Moreover, POAA revealed good stability in the recycling processes. Extraction-precipitation strategy is simple, efficient and sustainable, which can effectively reduce the volume of sludge in the process of wastewater treatment and produce copper concentrated solution with industrial value, which has revealed application potential for the clean production of copper smelting enterprises.

Characterization of Cuban and Brazilian natural zeolites by photoacoustic spectroscopy and electron paramagnetic resonance

This report describes the photoacoustic and electron paramagnetic resonance investigations of Brazilian and Cuban zeolites. Photoacoustic optical absorption measurements indicate the presence of iron (Fe3+) ions with their respective transition bands for both zeolites. Two species of manganese (Mn2+ and Mn3+) were identified in the Cuban sample and the electronic transitions assigned. Iron and manganese ions were confirmed through nonradiative relaxation (τ) and characteristic diffusion (τβ) times evaluation, whose values were found to be τBRA = 5.40 ms, τCUB = 4.60 ms, τβBRA = 387 μs and τβCUB = 305 μs. Crystal field (Dq-BRA/Dq-CUB = 1048 cm-1/945 cm-1) plus Racah (B-BRA/B-CUB = 457 cm-1/813 cm-1 and C-BRA/C-CUB = 3655 cm-1/2496 cm-1) parameters were assessed as well. Paramagnetic resonance corroborated Fe3+ ions present in the Brazilian zeolite occupying sites showing axial and/or rhombic symmetry distortions. For the Cuban sample, results reveal the characteristic hyperfine sextet lines of Mn2+ overlapping the Fe3+ line. Values of Landé factor and isotropic hyperfine splitting constant were found to be 2.0 and 9.7 mT, respectively. This tells us that the Mn2+ lies in octahedral symmetry probably replacing calcium ions and point towards an ionic bonding character of the Mn2+ and its surroundings.

A review on recent advances in electrodeionization for various environmental applications

The growing contamination of ecosystems necessitates the development of long-term pollution-removal technologies. Electrodeionization, in notably, has newly proven as an efficient method for removing ionic chemicals from polluted waterways. The fact that continuous electrodeionization is a greener technique is most probably the biggest cause for its success. It replaces the toxic chemicals typically required to replenish resins with electric power, therefore eliminating the wastewater involved with resin renewal. In water treatment, electrodeionization solves some of the drawbacks of ion exchange resin beds, particularly ion dumping as beds expire. This comprehensive review explores the theory, principles, and mechanisms of ion movement and separation in an electrodeionization unit. Also, it investigated the construction and usage, notably in removing heavy metal and its current developments in electrodeionization unit. Recent advances in Electrodeionization like polarity reversal, Resin wafer Electrodeionization, membrane free Electrodeionization, and electrostatic shielding with novel materials and hybrid process along with Electrodeionization were addressed. Further advancements are expected in electrodeionization systems that exhibit better efficacy while running at lower costs due to decreased energy usage, rendering them appealing for industrial scale up across a wide range of applications across the world.

Multi-component adsorption study by using bone char: modelling and removal mechanisms

Highly efficient simultaneous removal of paracetamol and Cu²⁺ ions from aqueous solutions was accomplished by using bovine bone char (BC). The adsorption behaviour was determined by kinetic and equilibrium studies of both single and binary system solutions. BC is a predominantly mesoporous material with a surface area of 103 m² g^-1. The influence of the initial pH on Cu²⁺ removal was tested, suggesting that the optimal pH was 3.0. The removal of paracetamol from single and binary systems was 9.45 and 12.7%, respectively. On the other hand, the Cu²⁺ removal was 36.2% for a single system, suggesting a higher affinity for BC. Moreover, in the case of binary mixtures, the presence of paracetamol led to an enhanced affinity of Cu²⁺ due to a synergistic/cooperative mechanism, which led to a copper removal of 97.3%. The cooperative model was successfully adjusted to the equilibrium data of the binary systems. The modelling results indicated the formation of a first adsorption layer where paracetamol and copper are retained, and a second layer with a great affinity for copper ions after the formation of a Cu-paracetamol complex, leading to higher removal of Cu²⁺.

Adsorption of Cu (II) Ions Present in the Distilled Beverage (Sugar Cane Spirit) Using Chitosan Derived from the Shrimp Shell

Cachaça (sugar cane spirit) is a typically Brazilian distilled beverage. Copper ions can be present in craft beverages despite their acceptance in the national and international market. This study aims to evaluate the efficiency of chitosan as an adsorbent in removing copper (II) from cachaça. The structural characteristics of the obtained chitosan and the effect of adsorbed copper were evaluated by Fourier Transform Infrared Spectroscopy (ATR-FTIR), viscosimetry, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The deacetylation reaction from chitin (shrimp shell) resulted in chitosan with a deacetylation degree of 88.9% (potentiometric titration) and 86.9% (FTIR), low crystallinity, and an estimated molecular weight of 162.96 kDa. The copper reduction rate was 84.09% evaluated by spectrophotometric titration and microwave-induced plasma optical emission spectrometry (MIP–OES). The amine groups of chitosan had adsorption affinity with copper ions, and the kinetic analysis showed a better fit of the data by the Elovich equation, suggesting that the chemosorption mechanism controlled the kinetic process. The results suggest that chitosan has the potential to improve the quality and safety of cachaça.

Invasive plants as biosorbents for environmental remediation: a review

Water contamination is an environmental burden for the next generations, calling for advanced methods such as adsorption to remove pollutants. For instance, unwanted biowaste and invasive plants can be converted into biosorbents for environmental remediation. This would partly solve the negative effects of invasive plants, estimated at 120 billion dollars in the USA. Here we review the distribution, impact, and use of invasive plants for water treatment, with emphasis on the preparation of biosorbents and removal of pollutants such as cadmium, lead, copper, zinc, nickel, mercury, chromate, synthetic dyes, and fossil fuels. Those biosorbents can remove 90-99% heavy metals from aqueous solutions. High adsorption capacities of 476.190 mg/g for synthetic dyes and 211 g/g for diesel oils have been observed. We also discuss the regeneration of these biosorbents.

β-cyclodextrin and its derivatives: application in wastewater treatment

Water is one of the basic necessities of life and having clean water is extremely important for human health. In recent years, β-cyclodextrin (β-CD)-based polymers and nanosystems have been extensively studied as adsorbents for the purpose of water purification. They present high efficiency and capability to remove inorganic, organic, and heavy metal impurities from wastewater as compared to conventional methods of water purification. β-CDs are cyclic polysaccharides having specific dimension of hydrophobic cavities and hydrophilic functional groups. The hydrophobic cavities form inclusion complexes through host-guest interactions. The hydroxyl groups form sites of hydrogen bonding and electrostatic interaction with pollutants. Additionally, they are also the sites of modification to bring about different derivatisation and polymerization reactions in order to impart desirable properties for efficient adsorption material. This article comprises of various derivatives of β-cyclodextrins: their nanoparticulate systems and their characterization and applications to remove different types of impurities from wastewater. The chemical reactions for their synthesis and mechanism of adsorption are highlighted.

Preparation and characterization of magnetic modified bone charcoal for removing Cu2+ ions from industrial and mining wastewater

Heavy metal water pollution is an urgent global problem to be addressed. Copper ions are common toxic heavy metal pollutants in wastewater. In order to remove the excessive copper ions in wastewater, in this study, chicken bone charcoal was modified by sodium dodecyl sulfonate and combined with magnetic nanoparticles prepared with ferric chloride hexahydrate and ferrous sulfate heptahydrate to produce a high efficiency adsorbent. The characterization of the magnetically modified bone charcoal was analyzed by scanning electron microscopy, surface and porosity analyses, FTIR and thermogravimetric analysis. The optimal adsorption conditions of magnetically modified bone charcoal for Cu²⁺ were obtained through batch experiments. The highest removal rate and adsorption capacity of Cu²⁺ was 99.98% and 15.057 mg/g, respectively, when the pH was 3.0, adsorbent dosage was 0.2 g, initial concentration of the Cu²⁺ solution was 50 mg/L, and temperature was 25 °C. The adsorption process fitted well with the Langmuir isotherm and the pseudo-second-order kinetic model. The regeneration experiment indicated that M-SDS-BC-500 maintained a high removal rate after five repetitions. The results suggest that the adsorbent has wide application prospects.

MXene-based designer nanomaterials and their exploitation to mitigate hazardous pollutants from environmental matrices

MXenes are a rapidly expanding and large family of two-dimensional (2D) materials that have recently garnered incredible research interests for diverse applications domains in various industrial sectors. Owing to unique inherent structural and physicochemical characteristics, such as high surface area, biological compatibility, robust electrochemistry, and high hydrophilicity, MXenes are appraised as a prospective avenue for environmental-clean-up technologies to detect and mitigate an array of recalcitrant hazardous contaminants from environmental matrices. MXene-based nanoarchitectures are thought to mitigate inorganic pollutants via interfacial chemical transformation and sorption, while three different mechanisms, including i) surface complexation and sorption (ii) catalytic activation and removal and (iii) radical's generation-based photocatalytic degradation, are involved in the removal of organic contaminants. Considering the application performance of MXenes on the incessant rise to expansion, in this review, we discuss the wide-spectrum applicability of diverse MXenes-based hybrid nanocomposites in environmental remediation. A brief description related to environmental pollutants, structural properties, chemical abilities, and synthesis route of MXenes is delineated at the start. Afterwards, the adsorption and degradative robustness of MXene-based designer nanomaterials for various contaminants including organic dyes, toxic heavy metals, pesticide residues, phenolics, antibiotics, radionuclides, and many others are thoroughly vetted to prove their potentiality in the arena of wastewater purification and remediation. Lastly, challenges and trends in assessing the wide-range applicability and scalability of MXenes are outlined. Seeing encouraging outcomes in plenty of reports, it can be concluded that MXenes-based nanostructures could be considered the next-generation candidates for water sustainability.

Snail Shells Adsorbent for Copper Removal from Aqueous Solutions and the Production of Valuable Compounds

This research explored the efficiency of snail shells powder (SSP) for Cu(II) removal from aqueous solutions and the production of valuable compounds from the residual product. To confirm its chemical and mineral components, the material was characterized by different instrumental techniques. The effects of experimental parameters such as the pH of the solution, the effect of SSP dose, particle size, and initial concentration of Cu(II) on the removal process were studied. The removal of Cu(II) was reasonably fast to be completed within a time frame of 90 min. The kinetics following the pseudo-second-order model (R2 = 0.979) were better compared to the pseudo-first-order model (R2 = 0.896). The increase in pH values leads to an increase in the amount of Cu(II) adsorbed. Afterward, the adsorption capacity reaches stability at pH near 7. The maximum Cu(II) removal occurred with a mass of 8 g·L−1 and a particle size of 300 μm. This particle size presents approximately 44.5% of SSP particles, which is the largest proportion of the sample as shown by particle size analysis. The adsorption isotherm was well described by Langmuir and Freundlich equations. The thermodynamic parameters values showed that the Cu(II) adsorption was a spontaneous and exothermic process. Furthermore, with the presence of CaCO3, the precipitation of Cu(II) in the form of posnjakite occurred with a high Cu(II) removal rate close to 99%. The residual SSP was used for the production of valuable compounds through the thermal decomposition process at various temperatures.

A highly efficient nanoscale tapioca starch prepared by high-speed jet for Cu2+ removal in simulated industrial effluent

BACKGROUND

Nanoscale tapioca starch (NTS) was successfully developed by high-speed jet in our previous study. In this study, the adsorption capacity of Cu²⁺ onto NTS was further discussed. The optimal adsorption conditions (pH, contact time, contact temperature, initial Cu²⁺ concentration, and adsorbent concentration), adsorption kinetics, isotherms, and thermodynamic were also evaluated.

RESULTS

The results showed that NTS exhibited excellent performance in adsorption of Cu²⁺ , with adsorption capacities of 122.31 mg g^-1 for Cu²⁺ (pH 7, 0.04 g L^-1 , 0.2 g L^-1 , 313.15 K and 10 min). The pseudo-second-order and Langmuir isotherms models could be used to explain the adsorption kinetics and adsorption equilibrium, respectively. The thermodynamic results showed that the adsorption process was spontaneous and endothermic with an increase in entropy. Cu²⁺ was adsorbed onto NTS, which was confirmed by energy dispersive spectrometry analysis.

CONCLUSION

These findings indicated that NTS might be an effective, environment-friendly and renewable bio-resource adsorbent for removing heavy metals in industrial effluent. © 2021 Society of Chemical Industry.

Magnetic and electric field accelerate Phytoextraction of copper Lemna minor duckweed

In accordance with the opinion of the World Health Organization and the World Water Council the development of effective technologies for the treatment of wastewater from heavy metals for their discharge into water bodies or reuse is an urgent task nowadays. Phytoremediation biotechnologies is the most environmentally friendly and cheapest way of the treatment of wastewater, suitable for sustainable development principals. The main disadvantage of the phytoremediation is the slow speed of the process. A method for accelerating the process of phytoremediation by the combined effect of magnetic and weak electric fields is proposed. The purpose of this study is to determine the values of the parameters of the magnetic and weak electric fields that are most suitable for extracting cuprum ions from wastewater using the higher aqua plants (Lemna minor). A corresponding technological process based on the results of the study is proposed. The results have shown that the removal of copper cations from sulfate solutions effectively occurs in the initial period of time (1–5 hours) under the influence of a magnetic field with an intensity of H = 2 kA/m. Under the combined influence of an electrical current with density j = 240 μA/cm² and a magnetic field (H = 2 kA/m) the highest rate of copper extraction by duckweed leaves is achieved. Under these conditions, the greatest growth and development of plant leaves occurs. The paper presents the results of determining of the parameters of the electrochemical release from the eluate of the spent phytomass of duckweed. It has been determined that the release of metal occurs at E = 0.32 V. An original scheme for wastewater treatment from copper with subsequent separation of copper from the spent phytomass of duckweed is proposed. In general, the presented results are a scientific justification of wastewater treatment technologies and a contribution to resolving the crisis in the field of fresh water supply. An important contribution in the circular economy is a technology recommendation proposed for recovering copper from duckweed after wastewater treatment.