N-doping effectively enhances the adsorption capacity of biochar for heavy metal ions from aqueous solution

One-pot synthesis of N-doped petroleum coke-based microporous carbon for high-performance CO2 adsorption and supercapacitors

Waste resource utilization of petroleum coke is crucial for achieving global carbon emission reduction. Herein, a series of N-doped microporous carbons were fabricated from petroleum coke using a one-pot synthesis method. The as-prepared samples had a large specific surface area (up to 2512 m2/g), a moderate-high N content (up to 4.82 at.%), and high population (55%) of ultra-micropores (<0.7 nm). Regulating the N content and ultra-microporosity led to efficient CO2 adsorption and separation. At ambient pressure, the optimal N-doped petroleum coke-based microporous carbon exhibited the highest CO2 uptake of 4.25 mmol/g at 25°C and 6.57 mmol/g at 0°C. These values are comparable or even better than those of numerous previously reported adsorbents prepared by multistep synthesis, primarily due to the existence of ultra-micropores. The sample exhibited excellent CO2/N2 selectivity at 25°C owing to the abundant basic pyridinic and pyrrolic N species; and showed superior CO2 adsorption-desorption cycling performance, which was maintained at 97% after 10 cycles at 25°C. Moreover, petroleum coke-based microporous carbon, with a considerably high specific surface area and hierarchical pore structure, exhibited excellent electrochemical performance over the N-doped sample, maintaining a favorable specific capacitance of 233.25 F/g at 0.5 A/g in 6 mol/L KOH aqueous electrolyte. This study provides insight into the influence of N-doping on the porous properties of petroleum coke-based carbon. Furthermore, the as-prepared carbons were found to be promising adsorbents for CO2 adsorption, CO2/N2 separation and electrochemical application.

Comparative study by microwave pyrolysis and conventional pyrolysis of pharmaceutical sludge: Resourceful disposal and antibiotic adsorption

Compared with conventional pyrolysis, microwave pyrolysis has superior heat transfer performance and promotes the decomposition of organic matter. The paper focuses on the harmless treatment and resource utilization of pharmaceutical sludge (PS) by microwave heating and conventional heating methods. The experimental results showed that the conventional pyrolysis gas is dominated by CO2, CO and H2. For microwave pyrolysis gas, the "microwave effect" promoted secondary cracking of volatile fractions and increases the content of CH4, CxHy, H2 and CO through condensation, aromatization, and dehydrogenation. Conventional pyrolysis oils contained the highest percentage of oxygenated compounds. However, high-temperature microwave radiation accelerated the cleavage of polar oxygenated molecular bonds and long-chain hydrocarbons, thereby increasing the aromatics content of pyrolysis oils. The solid residues obtained from microwave pyrolysis is highly graphitized and porous, with a surface area of 146.2 m2/g. Furthermore, the solid residue was rich in pyridine-N and pyrrole-N that could be utilized for adsorption and catalysis. The MA-600 removes up to 99% of tetracycline (TC) in 6 h. It was also found that the adsorption process of TC by the two pyrolysis residues was consistent with the proposed secondary and Freundlich models.

Na/N Co-doped Seaweed Biochar Composite for Efficient Removal of Aqueous Pb(II) and Cu(II)

Pollution from harmful heavy metal ions such as Pb(II) and Cu(II) is causing serious environmental and health problems. In this study, Sodium and nitrogen co-doped porous carbon material (Na/NABc) was successfully prepared from seaweed, sodium hydroxide, and dicyandiamide. The experimental results showed that Na/NABc is an excellent adsorbent for the effective removal of Pb(II) and Cu(II) from water bodies. Specifically, 99.8% of Pb(II) and 64.6% Cu(II) (100 mg/L) were removed within 12 h using 10 mg Na/NABc(10%) at 25 °C. The adsorption of Pb(II) and Cu(II) in aqueous solution by Na/NABc(10%) was efficient and rapid in the first stage. The theoretical maximum removal capacities of Na/NABc for Pb(II) and Cu(II) were 959.6 and 299.1 mg/g, respectively. Pb(II) and Cu(II) ions were adsorbed quickly in the first 60 min, and the kinetics data were generally consistent with a pseudo-second-order model. Na/NABc(10%) had a large distribution coefficient for Pb(II) (8.38 L/mg) and Cu(II) (1.17 L/mg). The possible mechanisms were precipitation, Ion exchange, and surface complexation. The removal rate can reach about 70% after five cycles, and the release of sodium meets the standard. The results of this study demonstrate the potential applicability of Na/NABc(10%) for adsorption of heavy metals from aqueous solution.

Separation and reutilization of heavy metal ions in wastewater assisted by p-BN adsorbent

Extracting heavy metal ions from wastewater has significant implications for both environmental remediation and resource preservation. However, the conventional adsorbents still suffer from incomplete ion removal and low utilization efficiency of the recovered metals. Herein, we present an extraction and reutilization method assisted by porous boron nitride (p-BN) containing high-density N atoms for metal recovery with simultaneous catalyst formation. The p-BN exhibits stable and efficient metal adsorption performance, particularly for ultra-trace-level water purification. The distribution coefficients towards Pb2+, Cd2+, Co2+ and Fe3+ can exceed 106 mL g-1 and the residual concentrations that reduced from 1 mg L-1 to 0.8-1.3 μg L-1 are much lower than the acceptable limits in drinking water standards of World Health Organization. Meanwhile, the used p-BN after Co ion adsorption can be directly adopted as a high-efficiency catalyst for activating peroxymonosulfate (PMS) in organic pollutant degradation without additional post-treatment, avoiding the secondary metal pollution and the problems of neglected manpower and energy consumption. Moreover, a flow-through multistage utilization system assisted by p-BN/polyvinylidene fluoride (PVDF) membrane is constructed for achieving both metal ion separation and reutilization in the removal of organic pollutants, providing a new avenue for sustainable wastewater remediation.

Application of machine learning in prediction of Pb2+ adsorption of biochar prepared by tube furnace and fluidized bed

Data mining by machine learning (ML) has recently come into application in heavy metals purification from wastewater, especially in exploring lead removal by biochar that prepared using tube furnace (TF-C) and fluidized bed (FB-C) pyrolysis methods. In this study, six ML models including Random Forest Regression (RFR), Gradient Boosting Regression (GBR), Support Vector Regression (SVR), Kernel Ridge Regression (KRR), Extreme Gradient Boosting (XGB), and Light Gradient Boosting Machine (LGBM) were employed to predict lead adsorption based on a dataset of 1012 adsorption experiments, comprising 422 TF-C groups from our experiments and 590 FB-C groups from literatures. The XGB model showed superior accuracy and predictive performance for adsorption, achieving R2 values for TF-C (0.992) and FB-C (0.981), respectively. Contrasting inferior results were observed in other models, including RF (0.962 and 0.961), GBR (0.987 and 0.975), SVR (0.839 and 0.763), KRR (0.817 and 0.881), and LGBM (0.975 and 0.868). Additionally, a hybrid dataset combining both biochars in Pb adsorption also indicated high accuracy (0.972) as obtained from XGB model. The investigation revealed that the influence of char characteristics and adsorption conditions on Pb adsorption differs between the two biochar. Specific char characteristics, particularly nitrogen content, significantly influence lead adsorption in both biochar. Interestingly, the influence of pyrolysis temperature (PT) on lead adsorption is found to be greater for TF-C than for FB-C. Consequently, careful consideration of PT is crucial when preparing TF-C biochar. These findings offer practical guidance for optimizing biochar preparation conditions during heavy metal removal from wastewater.

Pristine and modified biochar applications as multifunctional component towards sustainable future: Recent advances and new insights

Employing biomass for environmental conservation is regarded as a successful and environmentally friendly technique since they are cost-effective, renewable, and abundant. Biochar (BC), a thermochemically converted biomass, has a considerably lower production cost than the other conventional activated carbons. This material's distinctive properties, including a high carbon content, good electrical conductivity (EC), high stability, and a large surface area, can be utilized in various research fields. BC is feasible as a renewable source for potential applications that may achieve a comprehensive economic niche. Despite being an inexpensive and environmentally sustainable product, research has indicated that pristine BC possesses restricted properties that prevent it from fulfilling the intended remediation objectives. Consequently, modifications must be made to BC to strengthen its physicochemical properties and, thereby, its efficacy in decontaminating the environment. Modified BC, an enhanced iteration of BC, has garnered considerable interest within academia. Many modification techniques have been suggested to augment BC's functionality, including its adsorption and immobilization reliability. Modified BC is overviewed in its production, functionality, applications, and regeneration. This work provides a holistic review of the recent advances in synthesizing modified BC through physical, chemical, or biological methods to achieve enhanced performance in a specific application, which has generated considerable research interest. Surface chemistry modifications require the initiation of surface functional groups, which can be accomplished through various techniques. Therefore, the fundamental objective of these modification techniques is to improve the efficacy of BC contaminant removal, typically through adjustments in its physical or chemical characteristics, including surface area or functionality. In addition, this article summarized and discussed the applications and related mechanisms of modified BC in environmental decontamination, focusing on applying it as an ideal adsorbent, soil amendment, catalyst, electrochemical device, and anaerobic digestion (AD) promoter. Current research trends, future directions, and academic demands were available in this study.

Pb(ΙΙ), Cd(ΙΙ), and Mn(ΙΙ) adsorption onto pruning-derived biochar: physicochemical characterization, modeling and application in real landfill leachate

The aim of this study was to systemically evaluate how different pyrolysis temperatures (400, 550, and 700 °C) and particle sizes (1-2 mm and 63-75 µm) were influenced biochar evolution, made from urban pruning waste, during pyrolysis process and to establish their relationships with biochar potential for removal of lead (Pb), cadmium (Cd), and manganese (Mn) from real municipal solid waste landfill leachate. The effects of pH (2-7), contact time (30-300 min) and adsorbent dosage (0.1-5 g L-1) on heavy metals removal were also examined. The results showed that physicochemical properties of biochar were greatly influenced by pyrolysis temperature. Particle size, however, showed little influence on biochar characteristics (p > 0.05). The yield, volatile matter, hydrogen and oxygen contents, and surface functional groups decreased consistently with increasing pyrolysis temperature. An increase in the pH, electrical conductivity, ash, fixed carbon, and specific surface area values was also found. In biochar samples formed at high temperatures (i.e., 550 and 700 °C), Fourier transform infrared spectroscopy-FTIR studies confirmed the increase in aromaticity. Field emission scanning electron microscopy-FESEM images showed differences in the microporous structure and lower size pores at higher temperatures. Biochar pyrolyzed at 700 °C with a particle size of 63-75 µm (i.e., Lv700-63) showed the highest removal efficiency performance. Pb and Cd ions were completely removed (100%) by 0.2 g L-1 Lv700-63 at 7.0 pH and contact times of 120 and 90 min, respectively. The maximum percentage removal of Mn was 86.20% at optimum conditions of 0.2 g L-1 Lv700-63 dosage, 7.0 pH, and 180 min contact time. The findings suggests that the surface complexation, π-electron coordination, and cation exchange were the dominant mechanisms for the Pb, Cd, and Mn removal onto Lv700-63.

Application of biochar on soil bioelectrochemical remediation: behind roles, progress, and potential

Bioelectrochemical systems (BESs) that combine electrochemistry with biological methods have gained attention in the remediation of polluted environments, including wastewater, sludge, sediments, and soils. The most attractive advantage of BESs is that the solid electrode is used as an inexhaustible electron acceptor or donor, and biocurrent directly converted from organics can afford the reaction energy of contaminant breakdown, crossing the internal energy barrier of endothermic degradation, which achieves a continuous biodegradation process without the simultaneous use of exogenetic chemicals and bioelectricity recovery. However, soil BESs are hindered by expensive electrode materials, difficult pollutant and electron transfer, low microbial competitive activity, and biocompatibility in contamination remediation. Fortunately, introducing biochar into soil BESs could reveal a high potential in addressing these BES inadequacies. The characteristics of biochar, e.g., conductivity, transferability, high specific surface area, high porosity, large functional groups, and biocompatibility, can improve the performance of soil BESs. In fact, biochar not only carries electrons but also transfers nutrients, pollutants, and even bacteria by facilitating transmission in the bioelectric field of BESs. Consequently, the abilities of biochar make for better functionality of BESs. This review collates information on the roles, application, and progress of biochar in soil BESs, and future prospects are given. It is beneficial for environmental researchers and engineers to extend BES application in environmental remediation and to assist the progress of carbon sequestration and emission reduction based on the inertia of biochar and the blocking of electron flow to form methane.

Effects of BC on metal uptake by crops (availability) and the vertical migration behavior in soil: A 3-year field experiments of crop rotation

Biochar (BC) has been substantiated to effectively reduce the available content of heavy metals (HMs) in soil-plant system; however, the risk of biochar (BC)derived dissolved organic matter (DOM) induced metal vertical migration has not been well documented, especially in the long-term field conditions. Therefore, this study investigated HM vertical migration ecological risks and the long-term effectiveness of the amendment of biochar in the three successive years of field trials during the rotation system. The results revealed that biochar application could increase soil pH and DOM with a decrease in soil CaCl2 extractable pool for Pb, Cu, and Cd. Furthermore, the results indicated a significant decrease in acid phosphatase activities and an increase in urease and catalase activities in the soil. Cucumber was shown to be safe during a three-year rotation system in the field. These results suggest that BC has the potential to enhance soil environment and crop yields. BC derived DOM-specific substances were identified using parallel factor analysis of excitation-emission matrix in deep soil (0-60 cm). The study incorporated HM concentration fluctuations in deep soils, providing an additional interpretation of DOM and co-migration of HMs.The environmental risk associated with the increase in DOM hydrophobicity should not be ignored by employing BC for soil HM remediation applications. The study enhances understanding of biochar-derived DOM's migration and stabilization mechanisms on heavy metals, providing guidelines for its use as a soil amendment.

Nano-biochar as a potential amendment for metal(loid) remediation: Implications for soil quality improvement and stress alleviation

Metal(loid) contamination of agricultural soils has become an alarming issue due to its detrimental impacts on soil health and global agricultural production. Therefore, environmentally sustainable and cost-effective solutions are urgently required for soil remediation. Biochar, particularly nano-biochar, exhibits superior and high-performance capabilities in the remediation of metal(loid)-contaminated soil, owing to its unique structure and large surface area. Current researches on nano-biochar mainly focus on safety design and property improvement, with limited information available regarding the impact of nano-biochar on soil ecosystems and crop defense mechanisms in metal(loid)-contaminated soils. In this review, we systematically summarized recent progress in the application of nano-biochar for remediation of metal(loid)-contaminated soil, with a focus on possible factors influencing metal(loid) uptake and translocation in soil-crop systems. Additionally, we conducted the potential/related mechanisms by which nano-biochar can mitigate the toxic impacts of metal(loid) on crop production and security. Furthermore, the application of nano-biochar in field trials and existing challenges were also outlined. Future studies should integrate agricultural sustainability and ecosystem health targets into biochar design/selection. This review highlighted the potential of nano-biochar as a promising soil amendment for enhancing the remediation of metal(loid)-contaminated agricultural soils, thereby promoting the synthesis and development of highly efficient nano-biochar towards achieving environmental sustainability.

Effect of different production methods on physicochemical properties and adsorption capacities of biochar from sewage sludge and kitchen waste: Mechanism and correlation analysis

Different pyrolysis methods, parameters and feedstocks result in biochars with different properties, structures and removal capacities for heavy metals. However, the role of each property on adsorption capacity and corresponding causal relationships remain unclear. Here, we investigated various physicochemical properties of biochar produced via three different methods and two different feedstocks to clarify influences of biomass sources and pyrolysis processes on biochar properties and its heavy metal adsorption performance. Experimental results showed biochars were more aromatic and contained more functional groups after hydrothermal carbonization, while they had developed pores and higher surface areas produced by anaerobic pyrolysis. The inclusion of oxygen resulted in more complete carbonization and higher CEC biochar. Different biochar properties resulted in different adsorption capacities. Biochar produced by aerobic calcination showed higher adsorption efficiency for Cu and Pb. Correlation analysis proved that pH, cation exchange capacity and degree of carbonization positively affected adsorption, while organic matter content and aromaticity were unfavorable for adsorption. Microstructure and components determined biochar macroscopic properties and ultimate adsorption efficiency for metal ions. This study identifies the degree of correlation and pathways of each property on adsorption, which provides guidance for targeted modification of biochar to enhance its performance in heavy metal removal.

Significant Differences in the Effects of Nitrogen Doping on Pristine Biochar and Graphene-like Biochar for the Adsorption of Tetracycline

To improve the adsorption efficiency of pollutants by biochar, preparing graphene-like biochar (GBC) or nitrogen-doped biochar are two commonly used methods. However, the difference in the nitrogen doping (N-doping) effects upon the adsorption of pollutants by pristine biochar (PBC) and GBC, as well as the underlying mechanisms, are still unclear. Take the tetracycline (TC) as an example, the present study analyzed the characteristics of the adsorption of TCs on biochars (PBC, GBC, N-PBC, N-GBC), and significant differences in the effects of N-doping on the adsorption of TCs by PBC and GBC were consistently observed at different solution properties. Specifically, N-doping had varied effects on the adsorption performance of PBC, whereas it uniformly improved the adsorption performance of GBC. To interpret the phenomenon, the N-doping upon the adsorption was revealed by the QSAR model, which indicated that the pore filling (VM) and the interactions between TCs with biochars (Ead-v) were found to be the most important two factors. Furthermore, the density functional theory (DFT) results demonstrated that N-doping slightly affects biochar's chemical reactivity. The van der Waals (vdWs) and electrostatic interactions are the main forces for TCs-biochars interactions. Moreover, N-doping mostly strengthened the electrostatic interactions of TCs-biochars, but the vdWs interactions of most samples remained largely unaffected. Overall, the revealed mechanism of N-doping on TCs adsorption by biochars will enhance our knowledge of antibiotic pollution remediation.

Feedstock nitrogen content mediates maximum possible Pb sorption capacity of biochars

The use of biochar for the adsorption of contaminants from soil and water has received considerable interest due to biochar's high surface area, negative charge, and resistance to degradation. However, a knowledge gap still exists concerning the optimum selection of feedstocks and pyrolysis temperatures to maximise sorption capacity for metals. In this study, biochars were produced from 4 different feedstock materials (hay, wheat straw, coco coir, and pine bark) at 10 pyrolysis temperatures ranging from 300 °C to 750 °C, at 50 °C intervals. Batch sorption experiments were conducted to determine the maximum Pb sorption capacity for each biochar using the Langmuir model. The sorption isotherms fit the Langmuir model well (generally R2 > 0.7). The Langmuir maximum sorption capacity increased with an increase in pyrolysis temperature, according to a sigmoidal relationship. A sigmoidal model was fit to the data to derive the theoretical maximum possible sorption capacity obtainable from a feedstock. We observed a positive correlation between the nitrogen content of the feedstock and the theoretical maximum possible sorption capacity obtainable from the feedstock. This relationship highlights the importance of nitrogen content in feedstock to create biochars with a high Pb sorption capacity. It is possible that cation-π interactions with heterocyclic N structures are the primary mechanism for the sorption of Pb to these biochars, and this warrants further investigation.

Preparation of N-doped porous biochar with high specific surface area and its efficient adsorption for mercury ion from aqueous solution

Herein, a new type of super active nitrogen-doped biochar sheet (SNBC) was prepared by two-step pyrolysis and KOH chemical activation with melamine and cherry kernel powder as precursors of nitrogen and carbon source for removing Hg2+ from wastewater. The N2 adsorption/desorption and scanning electron microscope characterization revealed that the resulted SNBC under 600 °C calcination owned huge specific surface area of 2828 m2/g and plenty of well-developed micropores, and X-ray photoelectron spectroscopy and Fourier transform-infrared spectroscopy analysis testified the existence of functional groups containing N and O, which could provide adsorption sites for Hg2+. The SNBC-600 showed high adsorption capacity for Hg2+ even at low pH, and interfering cations had little effect on the adsorption. The adsorption process was rapid and dynamic data fit the pseudo-second-order dynamic model well. The maximum adsorption capacity of Hg2+ on SNBC-600 calculated by Langmuir model was 230 mg/g. After six times of reuse, the adsorption capacity still exceeded 200 mg/g, exhibiting good reusability. The designed microfiltration membrane device base on SNBC-600 could remove low concentration of Hg2+ effectively from solution. This study provided a simple and environment-friendly method for manufacturing nitrogen-doped biochar sheet, which was of great significance in the practical application of Hg2+ pollution treatment.

Hydrothermal Ammonia Carbonization of Rice Straw for Hydrochar to Separate Cd(II) and Zn(II) Ions from Aqueous Solution

Hydrochar is considered to be a good adsorbent for the separation of metal ions from aqueous solutions. However, the yield of hydrochar from raw straw is generally low, because the hydrothermal carbonization occurs via dehydration, polymerization, and carbonization. In this work, various hydrochar samples were prepared from rice straw with nitrogen and phosphorus salt; moreover, toilet sewage was used instead of nitrogen, and phosphorus salt and water were used to promote the polymerization and carbonization process. The modified carbon was characterized using XRD, XPS, SEM, and FTIR, and the adsorption capacity was investigated. A significant increase in hydrochar yield was observed when toilet sewage was used as the solvent in the hydrothermal carbonization process. The adsorption capacity of N/P-doped rice straw hydrochar for Cd2+ and Zn2+ metal ions was 1.1-1.4 times higher than that those using the rice straw hydrochar. The Langmuir models and pseudo-second-order models described the metal adsorption processes in both the single and binary-metal systems well. The characterization results showed the contribution of the surface complexation, the electrostatic interaction, the hydrogen bond, and the ion exchange to the extraction of Cd2+ and Zn2+ using N/P-doped rice straw hydrochar.

Selective removal of Pb(II) from yellow rice wine using magnetic carbon-based adsorbent

BACKGROUND

The non-distilled property and prolonged production period of yellow rice wine have significantly increased the metal residue problem, posing a threat to human health. In this study, a magnetic carbon-based adsorbent, named magnetic nitrogen-doped carbon (M-NC), was developed for the selective removal of lead(II) (Pb(II)) from yellow rice wine.

RESULTS

The results showed that the uniformly structured M-NC could be easily separated from the solution, exhibiting a high Pb(II) adsorption capacity of 121.86 mg g-1 . The proposed adsorption treatment showed significant Pb(II) removal efficiencies (91.42-98.90%) for yellow rice wines in 15 min without affecting their taste, odor, and physicochemical characteristics of the wines. The adsorption mechanism studied by X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared (FTIR) analyses indicated that the selective removal of Pb(II) could be attributed to the electrostatic interaction and covalent interaction between the empty orbital of Pb(II) and the π electrons of the N species on M-NC. Additionally, the M-NC showed no significant cytotoxicity on the Caco-2 cell lines.

CONCLUSION

Selective removal of Pb(II) from yellow rice wine was achieved using magnetic carbon-based adsorbent. This facile and recyclable adsorption operation could potentially address the challenge of toxic metal pollution in liquid foods. © 2023 Society of Chemical Industry.

Efficient removal of both heavy metal ion and dyes from wastewater using magnetic response adsorbent of block polymer brush-grafted N-doped biochar

The recovery of biomass from agricultural and forestry waste could realize effective utilization of waste and synthesis of novel adsorbent. Herein, porous biochar was prepared from waste ginkgo biloba leaves and modified by Reversible Addition-Fragmentation Chain Transfer Polymerization (RAFT). And the prepared adsorbent exhibited excellent adsorption capacity owing to its abundant functional groups and porous structure. In addition, the adsorption capacities of the prepared adsorbent for Malachite Green (MG), Amaranth (AM) and Cr (Ⅵ) were 422.59, 373.75 and 368.82 mg/g, respectively, surpassing those of many previously reported materials. Subsequently, the influence of various factors on adsorption performance was studied. The results showed that adsorption of MG, AM and Cr (Ⅵ) on adsorbent followed pseudo-second-order and Langmuir models and the adsorbent also displayed excellent cycling performance. The experimental results of application in various water samples showed that the adsorbent had outstanding adsorption performance in real water samples, further proving that the adsorbent had wide application and practicability. Finally, a simple adsorption column was used for filtration experiments to simulate industrial application. The results were exhibited that the adsorbent had great potential in treating wastewater containing MG, AM and Cr (Ⅵ).

Impacts of biochar materials on copper speciation, bioavailability, and toxicity in chromated copper arsenate polluted soil

Trace element polluted soils pose risks to human and environmental health. Biochar can decrease trace element bioavailability in soils, but their resulting ability to reduce soil toxicity may vary significantly depending on feedstocks used, pyrolysis conditions, and the target pollutants. Chromated copper arsenate (CCA) polluted sites are common, but only very few types of biochar have been tested for these sites. Hence, we tested fourteen well-characterized biochar materials for their ability to bind Cu and reduce toxicity in a CCA polluted soil in a 56-day experiment. Biochar (1%, wt/wt) increased plant (wheat, Triticum aestivum L.) shoot and root growth by 6-58% and 0-73%, reduced soil toxicity to Arthrobacter globiformis by 7-55%, decreased bioavailable Cu (Pseudomonas fluorescens bioreporter) by 5-65%, and decreased free Cu2+ ion activities by 27-89%. The A. globiformis solid-contact test constituted a sensitive ecotoxicological endpoint and deserves further attention for assessment of soil quality. Oil seed rape straw biochar generally performed better than other tested biochar materials. Biochar performance was positively correlated with its high cation exchange capacity, multiple surface functional groups, and high nitrogen and phosphorus content. Our results pave the way for future selection of feedstocks for creation of modified biochar materials with optimal performance in CCA polluted soil.

From Waste to Resource: Valorization of Lignocellulosic Agri-Food Residues through Engineered Hydrochar and Biochar for Environmental and Clean Energy Applications-A Comprehensive Review

Agri-food residues or by-products have increased their contribution to the global tally of unsustainably generated waste. These residues, characterized by their inherent physicochemical properties and rich in lignocellulosic composition, are progressively being recognized as valuable products that align with the principles of zero waste and circular economy advocated for by different government entities. Consequently, they are utilized as raw materials in other industrial sectors, such as the notable case of environmental remediation. This review highlights the substantial potential of thermochemical valorized agri-food residues, transformed into biochar and hydrochar, as versatile adsorbents in wastewater treatment and as promising alternatives in various environmental and energy-related applications. These materials, with their enhanced properties achieved through tailored engineering techniques, offer competent solutions with cost-effective and satisfactory results in applications in various environmental contexts such as removing pollutants from wastewater or green energy generation. This sustainable approach not only addresses environmental concerns but also paves the way for a more eco-friendly and resource-efficient future, making it an exciting prospect for diverse applications.

Conversion of solid wastes and natural biomass for deciphering the valorization of biochar in pollution abatement: A review on the thermo-chemical processes

This overview addresses the formation of solid trash and the various forms of waste from a variety of industries, which environmentalists have embraced. The paper investigates the negative effects on the environment caused by unsustainable management of municipal solid trash as well as the opportunities presented by the formal system. This examination looks at the origins of solid waste as well as the typical treatment methods. Pyrolysis methods, feedstock pyrolysis, and lignocellulosic biomass pyrolysis were highlighted. Explain in detail the various thermochemical processes that take place during the pyrolysis of biomass. Due to its carbon content, low cost, accessibility, ubiquitousness, renewable nature, and environmental friendliness, biomass waste is a unique biochar precursor. This study looks at the different types of biomass waste that are available for treating wastewater. This study discussed a wide variety of reactors. Adsorption is the standard method that is used the most frequently to remove hazardous organic, dye, and inorganic pollutants from wastewater. These pollutants cause damage to the environment and water supplies, thus it is important to remove them. Adsorption is both simple and inexpensive to utilize. Temperature-dependent conversions explain the kinetic theories of biomaterial biochemical degradation. This article presents a review that explains how pyrolytic breakdown char materials can be used to reduce pollution and improve environmental management.

Rape straw biochar enhanced Cd immobilization in flooded paddy soil by promoting Fe and sulfur transformation

Cd is normally associated with sulfide and Fe oxides in flooded paddy soil. The mechanisms of biochar enhanced Cd immobilization by promoting Fe transformation and sulfide formation are unclear. Rape straw biochar (RSB) pyrolyzed at 450 °C (LB) and 800 °C (HB) was added to Cd-contaminated paddy soil at 1% (LB1, HB1) and 2% (LB2, HB2) doses. The results showed that Fe/Mn oxide-Cd (Fe/Mn-Cd) and free Fe oxide (Fed) concentrations decreased in the first 12 days and then rose, while Fe2+ in pore water (W-Fe2+) tended to rise first and then fall. The electron transfer rate of soil in the HB2 treatment was 4.9-fold higher than that in the treatment without biochar (CK). Fe oxide reduction was enhanced by RSB, with a maximum increase in W-Fe2+ by 62.1% in HB2 on Day 12. The negative correlation between W-Fe2+ and Fed showed that Fe2+ promoted the reformatted of seconded Fe minerals after Day 12, and the Fed in the HB2 treatments increased by 31.5% in this period. RSB addition also promoted the reformation of poorly crystallized Fe oxide (Feo) by increasing soil pH, which increased by 17.2% and 15.1% on average in the LB2 and HB2 treatments, respectively, compared to CK. Compared to Day 7, the increased rate of Fe/Mn-Cd on Day 30 in RSB was approximately twice that of CK. Compared to the molybdate group, the maximum decrease in CaCl2-Cd was 29.1% in LB2 on Day 12. LB2 increased SO42- and acid-volatile sulfide concentrations by 6.9- and 4.1-fold, respectively, compared to CK. These results suggested that RSB, particularly HB, promoted more Cd adsorption in Fe minerals by increasing Fe hydroxylation and recrystallization processes. LB increased the contribution of sulfide to Cd immobility.

Biological calcium carbonate enhanced the ability of biochar to passivate antimony and lead in soil

The mechanism of immobilization of heavy metals in the soil using biochar has been studied extensively. However, the decomposition of biochar by biological and abiotic factors can reactivate the immobilized heavy metals in soil. Previous research showed that the addition of biological calcium carbonate (bio-CaCO3) can significantly increase the stability of biochar. However, the influence of bio-CaCO3 on the ability of biochar to immobilize heavy metals remains unclear. Therefore, this study evaluated the effect of bio-CaCO3 on the use of biochar to immobilize the cationic heavy metal lead and the anionic heavy metal antimony. The addition of bio-CaCO3 not only significantly improved the passivation ability of Pb and Sb but also reduced their migration in the soil. Mechanistic studies have shown that the reasons for the enhanced ability of biochar to immobilize heavy metals can be summarized in three aspects. First, the introduced inorganic component CaCO3 can precipitate and exchange ions with lead and antimony. Second, the N element in the organic component of bio-CaCO3 underwent polycondensation with the organic carbon in biochar to form pyridine N and pyrrole N structures, which can form a strong complex with lead and antimony. Pyridine N complexes more strongly than pyrrole N. Third, bio-CaCO3 increased the degree of aromatization and the surface π-electron density of biochar, which enhanced the ability of biochar to adsorb heavy metals. This study will provide a new concept for the application of biochar as an amendment to remediate heavy metals in the soil.

Bamboo-derived nitrogen-doping magnetic porous hydrochar coactivated by K2FeO4 and CaCO3 for phenol removal: Governing factors and mechanisms

In this study, a novel nitrogen-doped magnetic Fe-Ca codoped biochar for phenol removal was successfully fabricated via a hydrothermal and coactivation pyrolysis method. A series of adsorption process parameters (K₂FeO₄ to CaCO₃ ratio, initial phenol concentration, pH value, adsorption time, adsorbent dosage and ion strength) and adsorption models (kinetic models, isotherms and thermodynamic models) were determined using batch experiments and various analysis techniques (XRD, BET, SEM-EDX, Raman spectroscopy, VSM, FTIR and XPS) to investigate the adsorption mechanism and metal-nitrogen-carbon interaction. The biochar with a ratio of Biochar: K₂FeO₄: CaCO₃ = 3:1:1 exhibited superior properties for adsorption of phenol and had a maximum adsorption capacity of 211.73 mg/g at 298 K, C₀ = 200 mg/L, pH = 6.0 and t = 480 min. These excellent adsorption properties were due to superior physicomechanical properties (a large specific surface area (610.53 m²/g) and pore volume (0.3950 cm³/g), a well-developed pore structure (hierarchical), a high graphitization degree (I_D/I_G = 2.02), the presence of O/N-rich functional groups and Fe-Ox,Ca-Ox, N-doping, as well as synergistic activation by K₂FeO₄ and CaCO₃). The Freundlich and pseudo-second-order models effectively fit the adsorption data, indicating multilayer physicochemical adsorption. Pore filling and π-π interactions were the predominant mechanisms for phenol removal, and H-bonding interactions, Lewis-acid-base interactions, and metal complexation played an important role in enhancing phenol removal. A simple, feasible approach with application potential to organic contaminant/pollutant removal was developed in this study.

Nitrogen-doped hydrochar prepared by biomass and nitrogen-containing wastewater for dye adsorption: Effect of nitrogen source in wastewater on the adsorption performance of hydrochar

Dye wastewater has become one of the main risk sources of environmental pollution due to its high toxicity and difficulty in degradation. Hydrochar prepared by hydrothermal carbonization (HTC) of biomass has abundant surface oxygen-containing functional groups, and therefore is used as an adsorbent to remove water pollutants. The adsorption performance of hydrochar can be enhanced after improving its surface characteristics through nitrogen-doping (N-doping). In this study, wastewater rich in nitrogen sources such as urea, melamine and ammonium chloride were selected as the water source for the preparation of HTC feedstock. The N atoms were doped in the hydrochar with a content of 3.87%-5.70%, and mainly in the form of pyridinic-N, pyrrolic-N and graphitic-N, which changed the acidity and basicity of the hydrochar surface. The N-doped hydrochar adsorbed methylene blue (MB) and congo red (CR) in wastewater through pore filling, Lewis acid-base interaction, hydrogen bond, and π-π interaction, and the maximum adsorption capacities of those were obtained with 57.52 mg/g and 62.19 mg/g, respectively. However, the adsorption performance of N-doped hydrochar was considerably affected by the acid-base property of the wastewater. In a basic environment, the surface carboxyl of the hydrochar exhibited a high negative charge and thus an enhanced electrostatic interaction with MB. Whereas, the hydrochar surface was positively charged in an acid environment by binding H⁺, resulting in an enhanced electrostatic interaction with CR. Therefore, the adsorption efficiency of MB and CR by N-doped hydrochar can be tuned by adjusting the nitrogen source and the pH of the wastewater.

Unravelling the Effect of Activators used in The Synthesis of Biomass-Derived Carbon Electrocatalysts on the Electrocatalytic Performance for CO2 Reduction

N-doped carbon materials can be efficient and cost-effective catalysts for the electrochemical CO2 reduction reaction (CO2 RR). Activators are often used in the synthesis process to increase the specific surface area and porosity of these carbon materials. However, owing to the diversity of activators and the differences in physicochemical properties that these activators induce, the influence of activators used for the synthesis of N-doped carbon catalysts on their electrochemical performance is unclear. In this study, a series of bagasse-derived N-doped carbon catalysts is prepared with the assistance of different activators to understand the correlation between activators, physicochemical properties, and electrocatalytic performance for the CO2 RR. The properties of N-doped carbon catalysts, such as N-doping content, microstructure, and degree of graphitization, are found to be highly dependent on the type of activator applied in the synthesis procedure. Moreover, the overall CO2 RR performance of the synthesized electrocatalysts is not determined only by the N-doping level and the configuration of the N-dopant, but rather by the overall surface chemistry, where the porosity and the degree of graphitization are jointly responsible for significant differences in CO2 RR performance.

Synergistic effect in simultaneous removal of cationic and anionic heavy metals by nitrogen heteroatom doped hydrochar from aqueous solutions

Industrial wastewater typically contains both cationic and anionic heavy metals; therefore, their simultaneous removal must be considered to ensure environmental sustainability. Herein, nitrogen heteroatom (N) doped hydrochar derived from corncob was prepared via facile NH₄Cl-aided hydrothermal carbonization and used for the simultaneous adsorption of divalent copper (Cu(II)) and hexavalent chromium (Cr(VI)) in aqueous solutions. During hydrothermal carbonization, NH₄Cl played a vital role as the porogen and N dopant, which contributed to the efficient adsorption affinity toward coexisting Cu(II) and Cr(VI). The theoretical maximum adsorption capacities of the N-doped hydrochar were determined to be 1.223 mmol/g for Cu(II) and 1.995 mmol/g for Cr(VI), which were much better than those of the pristine hydrochar. Furthermore, in the binary-component system, the synergistic effect between Cu(II) and Cr(VI) significantly promoted the adsorption affinity of N-doped hydrochar, resulting in adsorption capacities for Cu(II) and Cr(VI) 9.48 and 1.92 times higher than those of the single-component system, respectively. A series of adsorption experiments and spectroscopic analyses demonstrated that multiple mechanisms, including electrostatic shielding, cation bridging, and redox reactions, mutually contributed to the synergistic effect in the adsorption of coexisting Cu(II) and Cr(VI). Overall, the N-doped hydrochar proved to be effective in simultaneously removing both cationic and anionic heavy metal pollutants.

Nano-chlorapatite modification enhancing cadmium(II) adsorption capacity of crop residue biochars

Cadmium (Cd) contamination in rivers or lakes has attracted worldwide concerns. Biochar pyrolyzed form crop residues (CR) could adsorb Cd(II) from aquatic environments, while the removal capacity of single CR biochar is relatively low. Nano-chlorapatite (nClAP) modification can enhance metal scavenging ability, but little is known about the behaviors and mechanisms of Cd(II) adsorption by nClAP-modified CR biochars. In this study, the influences of feedstock type, pyrolysis temperature, nClAP modification and aquatic environments on Cd(II) adsorption of biochars derived from rice (RB) and wheat (WB) husks were investigated comprehensively. Results showed that the pristine RB and WB showed low and similar Cd(II) adsorption capacities, while the rise of pyrolysis temperatures from 300 to 600 °C significantly improved the adsorption capacities. The Cd(II) adsorption of both RB and WB was regarded as monolayer chemical processes controlled by chemical precipitation, surface complexation and cation exchange mechanisms. Moreover, the nClAP modification notably enhanced Cd(II) adsorption capacities from 13.2 to 39.9 mg·g^-1 of pristine biochars to 25.2-60.7 mg·g^-1 of modified biochars attributed to the improved contribution of Cd(II)-phosphate precipitation. Among all biochars, the nClAP-modified RB and WB pyrolyzed at 500 °C had the highest Cd(II) adsorption capacities with 60.7 and 48.3 mg·g^-1, respectively. These biochars could maintain good adsorption performances under the neutral-alkaline (pH 6-8), low ionic strength, high dissolved organic matter and all oxidation-reduction potential conditions. In conclusion, this study reveals the importance of nClAP modification to optimize Cd(II) adsorption of CR biochars, which provides a promising future for its practical application in aquatic Cd(II) scavenging.

Nitrogen availability in biochar-based fertilizers depending on activation treatment and nitrogen source

Different activation and N-doping treatments were used to produce biochar-based fertilizers (BBFs) with increased N concentration and slow N release. Pristine biochars were produced by pyrolysis of olive tree pruning feedstock at low and high temperatures (400 and 800 °C). These biochars were activated either by ultrasonication, or oxidation with hydrogen peroxide (H₂O₂) or nitric acid (HNO₃) to increase their N retention potential. Subsequently biochars were enriched with N with either urea or ammonium sulfate. The activation of low-temperature biochars with HNO₃ was the most effective treatment leading to new surface carboxylic groups that facilitated the later enrichment with N. When treated with urea, BBFs reached 7.0 N%, whereas the H₂O₂ activation only allowed an increase up to 2.0 N%. The use of urea as the external N source was the most efficient for incorporating N. Urea treated biochars had a water-soluble fraction that represented up to 14.5 % of the total N. The hydrolyzable N fraction, composed by amides and simple N heterocycles originated by the N-doping treatments, and nitro groups generated from HNO₃ activation, represented up to 60 % of the total N. This study relates the N chemical forms in the new BBFs to potential N availability in soil. The presence of water-soluble, hydrolyzable and non-hydrolyzable N implied that these BBFs may supply N that would be progressively available for plants, acting as slow-release fertilizers.

Remediation of cadmium-contaminated soil by micro-nano nitrogen-doped biochar and its mechanisms

Cadmium-contaminated soils are an urgent problem that needs to be solved in many countries and regions. In this study, a new heavy metal passivator, micro-nano nitrogen-doped biochar (Nm-NBC), was prepared by introducing nitrogen into biochar. Soybean was used as an experimental plant to compare the effects of corn straw biochar (CBC, not modified), ammonium chloride modified corn straw biochar (NBC), and micro-nano nitrogen-doped biochar (Nm-NBC) on the remediation of Cdcontaminated soil. The results showed that the biomass of soybean, pH, organic matter, and total nitrogen content of the Cd-contaminated soil significantly increased, and the available Cd in soil significantly reduced (P < 0.05) when CBC, NBC, and Nm-NBC were added. The effect was as follows: Nm-NBC > NBC > CBC; Nm-NBC had the best result. When 1% Nm-NBC added to the soil, the Cd content in beans reduced by 68.09%. BET, FTIR, XPS, and SEM were used to analyze the characteristics of Nm-NBC and its mechanisms in the remediation of Cd-contaminated soils. The results showed that Nm-NBC had larger specific surface area and abundant functional groups; -COOH and graphitic nitrogen in Nm-NBC can form Cd-O bond and Cd-π with Cd(II) in the soil. Therefore, Nm-NBC prepared by introducing nitrogen into biochar has a promising application in the remediation of Cd-contaminated soil.

Efficient Adsorption of a Sulfonamide Antibiotic in Aqueous Solutions with N-doped Magnetic Biochar: Performance, Mechanism, and Reusability

Conventional biochar has limited effectiveness in the adsorption of sulfonamide antibiotics, while modified biochar exhibits greater adsorption potential. Residues of sulfamethoxazole (SMX) in the aquatic environment can threaten the safety of microbial populations as well as humans. In this study, iron-nitrogen co-doped modified biochar (Fe-N-BC) was prepared from palm fibers and doped with Fe and urea via synthesis at 500 °C. Fe-N-BC has a richer surface functional group based on elemental content, X-ray photoelectron spectroscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The Brunauer-Emmett-Teller (BET) specific surface area test exhibited Fe-N-BC, which possessed a greater surface area (318.203 m²/g) and a better developed pore structure (0.149 cm³/g). The results of the hysteresis loop and the Raman spectrum show that Fe-N-BC has a higher degree of magnetization and graphitization. Fe-N-BC showed a remarkable adsorption capacity for SMX (42.9 mg/g), which could maintain 93.4% adsorption effect after four cycles, and 82.8% adsorption capacity in simulated piggery wastewater. The adsorption mechanism involves pore filling, surface complexation, electrostatic interactions, hydrogen bonding, and π-π EDA interactions. The results of this study show that Fe-N-BC prepared from palm fibers can be a stable, excellent adsorbent for SMX removal from wastewater and has promise in terms of practical applications.

N-doped carbon fibers in situ prepared by hydrothermal carbonization of Camellia sinensis branches waste for efficient removal of heavy metal ions

N-doped carbon fibers (NCFs) were in situ prepared by Camellia sinensis branches waste through hydrothermal carbonization with urea/ZnCl₂ at 160-280 °C under 0.8-8.9 MPa. The structural characteristics of NCFs were investigated by elemental analysis, SEM, TEM, XRD, XPS, Raman spectra, and BET surface area. The highest N content of NCFs obtained at 280 °C was 8.96%, and the main forms of doped N were pyridinic N, pyrrolic N, and graphitic N. Moreover, NCFs were applied to remove metal ions successfully. The results showed that NCF-240 had the maximum adsorption amounts of 106.52, 125.23, and 153.49 mg/g for Cu²⁺, Pb²⁺, and Zn²⁺, respectively, while NCF-280 had the best removal ability on Cr⁶⁺ (145.67 mg/g). Finally, it demonstrated that the adsorption behavior of NCFs was well fitted by the pseudo-second-order kinetic and the Langmuir adsorption isotherm models.

Effect of nitrogen functional groups on competitive adsorption between toluene and water vapor onto nitrogen-doped spherical resorcinol-formaldehyde resin-based activated carbon

To elucidate the effect of nitrogen functional groups on the competitive adsorption of toluene and water vapor, a series of N-doped resorcinol-formaldehyde resin-based activated carbons using g-C₃N₄ as the nitrogen source were prepared, which possessed different N contents (1.29-6.14%). The competitive adsorption characteristics and mechanisms were investigated by characterizations, dynamic adsorption experiments, adsorption isotherms, and density functional theory calculations. Results showed that the normalized toluene adsorption capacity under 50 RH% was consistent with the N content, revealing that nitrogen functional groups can enhance the competitive adsorption for toluene under a humid atmosphere. Adsorption isotherms analysis suggested that nitrogen functional groups can not only accelerate the adsorption of toluene but also improve the hydrophobicity of carbon surface. Competitive adsorption mechanisms were ascribed to π-π interactions and electrostatic interactions. Specifically, graphitic-N and pyridinic-N enhance competitive adsorption for toluene through reinforced π-π interactions with toluene and weakened electrostatic interactions with water molecule. However, pyrrolic-N improve the competitive adsorption, which is principally attributed to enhanced π-π interactions with toluene. Furthermore, it was found that the reusability of activated carbon could be improved by nitrogen functional groups. This study provides theoretical hints to develop volatile organic compound adsorbents in the presence of water vapor.

One-step preparation of Fe/N co-doped porous biochar for chromium(VI) and bisphenol a decontamination in water: Insights to co-activation and adsorption mechanisms

Herein, magnetic nitrogen doped porous biochar (Fe/N-PBC) was prepared by mixing KHCO₃, K₂FeO₄ and CO(NH₂)₂ through one-step pyrolysis, and was employed for adsorbing Cr(VI) and BPA in water. The whole co-activated process was accompanied with pore-forming, carbon thermal reduction and element doping. Specifically, the developed microporous structures and high surface area of Fe/N-PBC (1093.68 m²/g) were achieved under synergistic activation of KHCO₃ and K₂FeO₄. Meanwhile, carbon thermal reduction process successfully converted K₂FeO₄ to Fe⁰ with introduction of heterocyclic-N (pyrrolic N and pyridinic N) structures by CO(NH₂)₂ doping. Fe/N-PBC exhibited outstanding uptake for Cr(VI) (340.96 mg/g) and BPA (355.14 mg/g), and possessed favorable regeneration properties after three cycles. Notably, the high-performance Cr(VI) removal was associated to reduction, electrostatic interaction, complexation, pore filling and ion exchange, while pore filling, hydrogen-bonding interaction and π-π stacking were responsible for BPA binding. This work presents reasonable design of Fe/N-carbon materials for Cr(VI)/BPA polluted water remediation.

N-Doped Biochar from Lignocellulosic Biomass for Preparation of Adsorbent: Characterization, Kinetics and Application

Medulla tetrapanacis is composed of a lignocellulosic biopolymer and has a regular porous structure, which makes it a potential biomass material for preparing porous N-doped biochar. Herewith, N-doped Medulla tetrapanacis biochar (UBC) was successfully prepared by modification with urea and NaHCO₃ under pyrolysis at 700 °C. The nitrogen-containing groups were efficiently introduced into biochar, and the micro-pore structures of the UBC were developed with sizeable specific surface area, which was loaded with massive adsorption sites. The adsorption kinetics and isotherms of the UBC conformed to pseudo-second-order and Langmuir model. The superior adsorption capacities of the UBC for methylene blue (MB) and congo red (CR) were 923.0 mg/g and 728.0 mg/g, and the capacities for Cu²⁺ and Pb²⁺ were 468.5 mg/g and 1466.5 mg/g, respectively. Moreover, the UBC had a stronger affinity for Cr³⁺ and Fe³⁺ in multiple metal ions and retained at a preferable adsorption performance for dyes and heavy metals after five cycles. Precipitation, complexation, and physical adsorption were the main mechanisms of the UBC-adsorbing metal ions and dyes. Thus, lignocellulosic biochar has great potential for removing dyes and heavy metals in aqueous solutions.

Current trends in production, morphology, and real-world environmental applications of biochar for the promotion of sustainability

Biochar has sparked a lot of interest in recent years for various applications such as contaminant removal, carbon sequestration and soil amendment. However, laboratory scale studies dominates over the real-world applications. In this study, we first enumerated on the various ongoing uses of biochar along with adsorption mechanism; and then identified the most suitable source, and efficient method for biochar production; and finally proposed real-world practical applications of biochar as an additive to control diffuse micropollutant pollution along the highways and railway tracks; as well as the pollution through agricultural runoff. We demonstrated that directly or indirectly, biochar can definitely help to achieve all the 17 Sustainable Development Goals. The study on the practical use of biochar is an emerging area, because a lot of research needs are there to realise the full-potential of biochar with ways of attaining sustainable development goals towards waste, energy and pollution management.

Biochar raw material selection and application in the food chain: A review

As one of the largest carbon emitters, China promises to achieve carbon emissions neutrality by 2060. Various industries are developing businesses to reduce carbon emissions. As an important greenhouse gas emissions scenario, the reduction of carbon emissions in the food chain can be achieved by preparing the wastes into biochar. The food chain, as one of the sources of biochar, consists of production, processing and consumption, in which many wastes can be transferred into biochar. However, few studies use the food chain as the system to sort out the raw materials of biochar. A systematic review of the food chain application in serving as raw materials for biochar is helpful for further application of such technique, providing supportive information for the development of biochar preparation and wastes treating. In addition, there are many pollution sources in the food production process, such as agricultural contaminated soil and wastewater from livestock and aquatic, that can be treated on-site to achieve the goal of treating wastes with wastes within the food chain. This study focuses on waste resource utilization and pollution remediation in the food chain, summarizing the sources of biochar in the food chain and analyzing the feasibility of using waste in food chain to treat contaminated sites in the food chain and discussing the impacts of the greenhouse gas emissions. This review provides a reference for the resource utilization of waste and pollution reduction in the food chain.

Facile Synthesis of Nitrogen Self-Doped Porous Carbon Derived from Cicada Shell via KOH Activation for Simultaneous Detection and Removal of Cu2+

Sensitive detection and efficient removal of heavy metal ions with high toxicity and mobility are of great importance for environmental monitoring and control. Although several kinds of functional materials have been reported for this purpose, their preparation processes are complicated. Herein, nitrogen self-doped activated porous biochar (NAC) was synthesized in a facile process via an activation–carbonization strategy from cicada shell rich in chitin, and subsequently employed as an effective functional material for the simultaneous determination and removal of Cu²⁺ from aqueous media. With its unique porous structure and abundant oxygen-containing functional groups, along with the presence of heteroatoms, NAC exhibits high sensitivity for the electrochemical sensing of Cu²⁺ in concentrations ranging from 0.001 to 1000 μg·L⁻¹, with a low detection limit of 0.3 ng·L⁻¹. Additionally, NAC presents an excellent removal efficiency of over 78%. The maximum adsorption capacity is estimated at 110.4 mg/g. These excellent performances demonstrate that NAC could serve as an efficient platform for the detection and removal of Cu²⁺ in real environmental areas.

Qualitative and quantitative investigation on adsorption mechanisms of Cd(II) on modified biochar derived from co-pyrolysis of straw and sodium phytate

Developing effective modification methods and obtaining a comprehensive understanding of adsorption mechanisms are essential for the practical application of biochars for the removal of heavy metals from solutions. In this study, rice straw was impregnated with sodium phytate and pyrolyzed at 350 °C, 450 °C, and 550 °C to synthesize modified biochars (i.e., MBC350, MBC450, and MBC550). The Cd(II) adsorption capacities and contributions of different mechanisms, including the effects of biochar-derived dissolved organic matter (BDOM), were investigated using batch sorption experiments and characterization analyses. The modification of sodium phytate promoted the pyrolysis of biomass, thereby increasing the BDOM content and aromatic structures at low and high pyrolysis temperatures, respectively. Moreover, the modification also increased the exchangeable Na⁺ and carbonate contents in the modified biochars. Compared with the raw biochars, the Cd(II) adsorption capacities of modified biochars increased by 3.3-4.3 times, and MBC550 had the highest Cd(II) adsorption capacity (126.5 mg/g), of which precipitation with minerals and interaction with π-electrons contributed 41.7% and 45.8%, respectively. However, at a lower pyrolysis temperature, the Cd(II) adsorption attributed to ion exchange and co-deposition with BDOM significantly increased, especially on MBC350 (33.9 and 12.6 mg/g, respectively). These results indicate that modification by sodium phytate effectively enhanced various adsorption mechanisms, thereby increasing the Cd(II) adsorption capacity. In addition, the contribution of co-deposition with BDOM to adsorption was unneglectable for the biochars pyrolyzed at low temperatures.

Effect of oxidative aging of biochar on relative distribution of competitive adsorption mechanism of Cd2+ and Pb2

In this study, aged biochar (CCB350 and CCB650) were obtained from pyrolysis of corn stalk biochar (CB350 and CB650) at the degree of 350 °C and 650 °C by artificial oxidation with hydrogen peroxide (H₂O₂). Also, the mechanism of Pb²⁺ and Cd²⁺ on fresh and aged biochars was analyzed qualitatively and quantitatively by batch adsorption experiments combined with characterization. The adsorption isotherm results showed that aging treatment decreased the adsorption capacity of Pb²⁺ and Cd²⁺ and inhibited the competitive adsorption behavior of heavy metals. In the single-metal system, precipitation and cation exchange were considered as the main adsorption mechanisms for CB350 and CB650, with a ratio of 40.07–48.23% and 38.04–57.19%, respectively. Competition between Pb²⁺ and Cd²⁺ increased the relative contribution of mineral precipitation, but decreased the contribution of cation exchange mechanism. Aging resulted in the rise of the contribution of surface complexation to the adsorption of Pb²⁺ and Cd²⁺ on biochars, especially in low-temperature biochars, but weakened the contribution of mineral precipitation to the adsorption. Further, the contribution of other adsorption mechanisms was significantly enhanced for high-temperature aged biochars. These results are important to evaluate its long-term application prospects in the natural environment.

Biochar production with amelioration of microwave-assisted pyrolysis: Current scenario, drawbacks and perspectives

In recent years, biomass has been reported to obtain a wide range of value-added products. Biochar can be obtained by heating biomass, which aids in carbon sinks, soil amendments, resource recovery, and water retention. Microwave technology stands out among various biomass heating technologies not only for its effectiveness in biomass pyrolysis for the production of biochar and biofuel but also for its speed, volumetrics, selectivity, and efficiency. The features of microwave-assisted biomass pyrolysis and biochar are briefly reviewed in this paper. An informative comparison has been drawn between microwave-assisted pyrolysis and conventional pyrolysis. It focuses mainly on technological and economic scenario of biochar production and environmental impacts of using biochar. This source of knowledge would aid in the exploration of new possibilities and scope for employing microwave-assisted pyrolysis technology to produce biochar.

Novel high capacity model for copper binary ion exchange on e-waste derived adsorbent resin

Heavy metal water pollution is a global concern in recent years. Copper is a toxic metal at higher concentrations (> 20 μg /g) and needs to be removed using ion exchanger systems. This study investigates the removal efficiencies of copper by the non-metallic fraction (NMF) waste printed circuit boards (PCBs). The high maximum adsorption capacity of copper by the PCB-derived material after activation with KOH was 2.65 mmol/g, and the experimental isotherm was best correlated by the Temkin model. Finally, this study presents a novel dual site adsorption/ion exchange mechanism, wherein the potassium (from the activation) and calcium (present in the structure) served as ion exchange sites for the copper in the solution. Therefore, this recycling study, focusing on cyclic environmental management, converts a major waste material to an activated ion exchange resin (high capacity) for the removal of copper from wastewater solutions and successfully regenerates the resin for re-use while producing an acidic copper solution for recovery by electrolysius or chemical salt precipitation.

Pyrolysis of food waste and food waste solid digestate: A comparative investigation

The effects of anaerobic digestion (AD) on pyrolysis were elaborated by comparing the pyrolysis performance of food waste (FW) and food waste solid digestate (FWSD). The pyrolysis mechanisms of FW and FWSD were revealed by experimental and kinetic analysis. The properties and potential applications of pyrolytic products from FW and FWSD were discussed. The results showed that part of organic matters of FW were consumed during AD, which altered the pyrolysis performance of FWSD. The pyrolytic gas from FW had better quality due to its higher lower heating value (LHV) (20.52 kJ/Nm³). The pyrolytic oil and biochar derived from FWSD showed better qualities as oil fuel and carbon-based absorbent. Pyrolysis of FWSD produced less nitrogen-containing pollutants (NCPs) indicated that AD coupled with pyrolysis is more environmental-friendly to treat FW. This study provides potential approach and theoretical guidance for the treatment and resource utilization of FW and FWSD.

Exploring the Adsorption of Pb on Microalgae-Derived Biochar: A Versatile Material for Environmental Remediation and Electroanalytical Applications

Biochar, a carbon material obtained by pyrolysis of biomasses, is increasingly applied in environmental remediation and sensing thanks to its functional properties, cost-effectiveness and eco-friendliness. The adsorption capacity of biochar, strictly dependent on its specific surface area, heteroatom doping and surface functional groups, is crucial for these applications. Here, biochar produced at low temperature (350 °C) from a marine microalga (Nannochloropsis sp.) is proposed as an efficient adsorbent of lead (II) ions in aqueous solution; this production strategy promotes the natural self-doping of biochar without requiring harsh conditions. The kinetics and thermodynamics of the adsorption process, as well as the effect of pH, ionic strength and dissolved organic matter on the adsorption efficiency were systematically assessed. The microalgae-derived biochar shows superior adsorption performances compared to a nutshell-derived one (used as a reference of lignocellulosic feedstocks) under all the tested conditions. The microalgae-derived biochar was finally used to decorate screen-printed carbon electrodes to improve the electroanalytical performances towards the voltammetric detection of lead (II) ions. A two-fold increase in sensitivity was obtained compared to the unmodified electrode thanks to the enhanced electron transfer and adsorption properties provided by biochar. These results highlight the potentialities of microalgae-derived biochar for environmental and sensing applications.