Efficient degradation of 2,4-dichlorophenol in aqueous solution by peroxymonosulfate activated with magnetic spinel FeCo2O4 nanoparticles

Fe and Zn co-doped carbon nanoparticles as peroxymonosulfate activator for efficient 2,4-dichorophenol degradation

Iron-mediated activation of peroxymonosulfate (PMS) has been of great interest for the effective removal of contaminants, but it still suffered from ineffective metal redox cycle rate, which resulted in unsatisfactory catalytic efficiency. Constructing bimetallic carbonaceous materials was effective way to improve the catalytic performance of iron-based heterogeneous system. In this study, magnetic bimetallic porous carbon composite (FZCx) was synthesized via Fe/Zn bi-MOFs pyrolysis for 2,4-dichlorophenol (2,4-DCP) degradation by peroxymonosulfate. Influences of different systems exhibited that 100% of 2,4-DCP was rapidly degraded at the conditions of catalyst dosage = 0.1 g L-1, PMS = 0.5 mM and initial pH = 9.0 within 30 min. The as-prepared FZC600 displayed excellent reusability and stability. Quenching experiments and EPR analysis manifested that SO4·- and 1O2 were primarily responsible for the rapid degradation of 2,4-DCP. Moreover, XPS, EPR and EIS was used to elaborate the bimetallic synergy effect, proving that the introduction of zinc can effectively promote periodic cycle of Fe2+/Fe3+ and improve catalysts durability and reusability. These findings highlighted the preparation of bimetallic based carbonaceous material with excellent PMS activation ability to remove refractory organics from wastewater and provided a depth insight into the promotion of bimetal synergy between zinc and iron on PMS activation process.

Peroxymonosulfate activation by graphene oxide-supported 3D-MoS2/FeCo2O4 sponge for highly efficient organic pollutants degradation

To address conventional powder catalysts' recovery and aggregation issues that greatly restrain their practical application, a recoverable graphene oxide (GO)-supported 3D-MoS₂/FeCo₂O₄ sponge (SFCMG) was developed through a simple impregnation pyrolysis method. SFCMG can efficiently activate peroxymonosulfate (PMS) to produce reactive species for rapid degradation of rhodamine B (RhB), with 95.0% and 100% of RhB being removed within 2 min and 10 min, respectively. The presence of GO enhances the electron transfer performance of the sponge, and the three-dimensional melamine sponge serves as a substrate to provide a highly dispersed carrier for FeCo₂O₄ and MoS₂/GO hybrid sheets. SFCMG exhibits a synergistic catalytic effect of Fe and Co, and facilitates the redox cycles of Fe(III)/Fe(II) and Co(III)/Co(II) by MoS₂ co-catalysis, which enhances its catalytic activity. Electron paramagnetic resonance results demonstrate that SO₄^•-, ·O₂^- and ¹O₂ are all involved in SFCMG/PMS system, and ¹O₂ played a prominent role in RhB degradation. The system has good resistance to anions (Cl^-, SO₄^2-, and H₂PO₄^-) and humic acid and excellent performance for many typical contaminants degradation. Additionally, it works efficiently over a wide pH range (3-9) and possesses high stability and reusability with the metal leaching far below the safety standards. The present study extends the practical application of metal co-catalysis and offers a promising Fenton-like catalyst for the treatment of organic wastewater.

In-situ preparation of yeast-supported Fe0@Fe2O3 as peroxymonosulfate activator for enhanced degradation of tetracycline hydrochloride

Nano zero-valent iron (nZVI) is extensively used as a peroxymonosulfate (PMS) activator but suffers from the ease of oxidation and agglomeration due to its high surface energy and inherent magnetism. Here, green and sustainable yeast was selected as a support material to firstly in-situ prepare yeast-supported Fe⁰@Fe₂O₃ and used for activating PMS to degrade tetracycline hydrochloride (TCH), one of the common antibiotics. Due to the anti-oxidation ability of the Fe₂O₃ shell and the support effect of yeast, the prepared Fe⁰@Fe₂O₃/YC exhibited a superior catalytic activity for the removal of TCH as well as some other typical refractory contaminants. The chemical quenching experiments and EPR results demonstrated SO₄^•- was the main reactive oxygen species while O₂^•-, ¹O₂ and ^•OH played a minor role. Importantly, the crucial role of the Fe²⁺/Fe³⁺ cycle promoted by the Fe⁰ core and surface iron hydroxyl species in PMS activation was elucidated in detail. The TCH degradation pathways were proposed by LC-MS and density functional theory (DFT) calculation. In addition, the outstanding magnetic separation property, anti-oxidation ability, and high environmental resistance of the catalyst were demonstrated. Our work may inspire the development of green, efficient, and robust nZVI-based materials for wastewater treatment.

Catalytic oxidation activation of peroxymonosulfate over Fe-Co bimetallic oxides for flurbiprofen degradation

In this research, FeCo₂O₄ nanomaterial was successfully synthesized by a typical sol-gel method and conducted as an effective agent for peroxymonosulfate (PMS) activation to eliminate antibiotics flurbiprofen (FLU), a strong nonsteroidal drug. FeCo₂O₄ nanomaterial was characterized by XRD, TEM, SEM, and XPS. Various characterization results proved that FeCo₂O₄ held stable spinel structure. The interfering factors including initial pH, PMS concentration, catalyst dosage, inorganic anions, and humic acid on FLU removal were also discussed. The conclusion was that the removal efficiency of FLU reached 98.2% within 120 min after adding FeCo₂O₄ (0.4 g L^-1) and PMS (3 mM). The optimal pH for FLU degradation was the initial pH of 6.5; too acidic or alkaline was not conductive to the degradation. The existence of HA and Cl^- restrained the degradation of FLU, and HCO₃^- promoted the removal, while the influence of NO₃^- and SO₄^2- could not be considered. The radical scavenging experiment confirmed that ^•OH, O₂^•-, and SO₄^•- participated in FLU removal and SO₄^•- functioned a leading role. FeCo₂O₄ showed high efficiency for PMS activation in pH range of 3.0 to 10.0. After the fourth cycle operation, the FLU removal rate exceeded 76.9%, and the Co leaching rate was low during the catalytic reaction. This study shows that FeCo₂O₄ nanomaterial is an efficient and environment-friendly catalyst, which can be applied for PMS activation to remove organic pollutants in water.

Robust polystyrene resin-supported nano-CoFe2O4 mediated peroxymonosulfate activation for efficient oxidation of 1-hydroxyethane 1,1-diphosphonic acid

Nanosized spinel cobalt ferrite (CoFe₂O₄) shows high performance in peroxymonosulfate (PMS) activation for decontamination in water, but is yet challenged by the easily leached Co(II) with high toxicity. Herein, macroporous polystyrene resin is used as the support to improve the stability of CoFe₂O₄ nanoparticles during PMS activation. CoFe₂O₄@S201 exerted high catalytic activity toward PMS activation for oxidation of 1-hydroxyethane 1,1-diphosphonic acid (HEDP), with the apparent rate normalized by Co content 38.2 times higher than that of the unsupported CoFe₂O₄. Meanwhile, one order of magnitude lower Co leaching (< 2.1 μg L^-1) was detected during the catalytic oxidation. The Co(II)-PMS complex was the primary oxidant responsible for the oxidation of HEDP. The catalytic durability and stability of CoFe₂O₄@S201 for degradation of HEDP in actual wastewater were systematically evaluated in both batch and continuous-flow mode. It is found that the organic resin, which is often considered to be intolerant to oxidation, is rather stable during the non-radical process. The total cobalt leaching of the fresh CoFe₂O₄@S201 cannot be ignored in the 100-h continuous-flow run. In contrast, much lower cobalt leaching and slightly higher oxidation efficiency were observed for the regenerated CoFe₂O₄@S201, which might be due to the removal of unreactive and unstable Co sites on the surface in the first trial. The findings shed light on the potential of organic supports for improving the stability and activity of nanosized CoFe₂O₄ and other nano-catalysts toward practical application.

Synthesis of bimetal MOFs for rapid removal of doxorubicin in water by advanced oxidation method

Doxorubicin (DOX) has been an emerging environmental pollutant due to its significant genotoxicity to mankind. Advanced oxidation processes are a potential strategy to remove DOX in water solution. To develop a highly efficient catalytic agent to remove DOX, bimetal MOFs were synthesized, with Cu²⁺ and Co²⁺ as the central ions and adenine as the organic ligand. This study investigated the degradation of DOX by Co/Cu-MOFs combined with peroxymonosulfate (PMS). It was found that the degradation of DOX by Co/Cu-MOFs can reach 80% in only 10 seconds. This can be explained by the charge transfer from Co(iii) to Co(ii) being accelerated by Cu²⁺, resulting in the rapid generation of free radicals, which was proved by the EIS Nyquist diagram. Co/Cu-MOFs can be reused by simply washing with water without inactivation. Therefore, Co/Cu-MOFs can be used as an efficient catalytic agent to degrade DOX in environmental water.

Efficient degradation of Rhodamine B in water by CoFe2O4/H2O2 and CoFe2O4/PMS systems: A comparative study

In this work, a comparative study of efficient degradation of Rhodamine B (RhB) in CoFe₂O₄/H₂O₂ and CoFe₂O₄/PMS systems was performed. Batch experiments indicated that the RhB degradation rate of CoFe₂O₄/H₂O₂ system reached 95.5% at 90 min under the condition of 0.5 g L^-1 of CoFe₂O₄ dosage, 10 mM of H₂O₂ concentration and 3.0 of initial pH. At certain conditions of initial pH = 7.0, 0.3 g L^-1 of CoFe₂O₄ dosage, 7 mM of PMS concentration, CoFe₂O₄/PMS system could completely degrade RhB within 90 min. EPR and quenching experiments indicated that •OH was the main active species of CoFe₂O₄/H₂O₂ system, and •OH, SO₄•^-, •O₂^- and ¹O₂ participated in RhB degradation of CoFe₂O₄/PMS system. The circulate of Co(II)/Co(III) and Fe(II)/Fe(III) on the CoFe₂O₄ surface promoted the formation of free radical species in the two system. In CoFe₂O₄/PMS system, the formed •O₂^- and SO₅•^- realized the generation of non-free radical species (¹O₂). The LC-MS results indicated that N-de-ethylation, chromophore cleavage, opening rings and mineralization were the main steps for the RhB degradation of the two systems. After five cycles of degradation experiment, the CoFe₂O₄/H₂O₂ and CoFe₂O₄/PMS systems still maintained the high degradation rate (85.2% and 92.4%) and low mass loss (2.7% and 3.09%). In addition, CoFe₂O₄/PMS system had better potential value for the actual water and multi-pollutant degradation than CoFe₂O₄/H₂O₂ system. Finally, the toxicity analysis and cost assessment of the two oxidation systems were preliminarily evaluated.

Sulfate radicals induced from peroxymonosulfate on electrochemically synthesized TiO2-MoO3 heterostructure with Ti-O-Mo bond charge transfer pathway for potential organic pollutant removal under solar light irradiation

Here, a novel method for synthesis of heterostructured TiO₂-MoO₃ (MT) nanosheets photocatalyst by utilizing a facile electrochemical method and examined it's photocatalytic activity by the degradation of tetracycline hydrochloride (TCH), a model of organic pollutants, in the presence of peroxymonosulfate (PMS) under solar light irradiation (SL) was reported for the first time. The influence of several factors on the degradation efficiency including the initial concentration of TCH, solution pH, catalyst dosage, PMS concentration, and the existence of inorganic anions was explored. The MT-15/PMS system displayed a promising photocatalytic performance and up to 97% of TCH was degraded in 90 min the rate of the degradation reaction of MT-15/PMS was the highest (0.05299 min^-1) compared to 0.00251, 0.00337, 0.00546, 0.00735, 0.01337min^-1of TiO₂-P25, TiO₂-P25/PMS, MoO₃, MoO₃/PMS, and MT-15 respectively. The enhancement can be attributed to several reasons. First, the 2D morphology of the optimized heterostructure photocatalyst plays a significant role in providing much more active sites on its surface. Next, the boosted light absorption efficiency and higher photoproduced electron-hole pair separation ability, induced by the unique direct transformation of photogenerated electrons from the valance band of TiO₂ to the conduction band of MoO₃ via the Ti-O-Mo bond formed at the interface of MT heterostructure. Finally, the appropriate accessible reactive sites for the activation of PMS together with the synergistic effect between activation of PMS and photocatalytic processes eased the production of active species for the degradation of pollutants. Based on the scavenger experiments and EPR analysis, hydroxide and sulfate radicals were found to be the dominant free radical active species in the degradation process. Furthermore, the synergistic degradation reaction mechanism was proposed.

Efficient organics heterogeneous degradation by spinel CuFe2O4 supported porous carbon nitride catalyst: Multiple electron transfer pathways for reactive oxygen species generation

Facilitating reactive oxygen species (ROS) generation is an effective way to promote the heterogeneous catalytic efficiency for organics removal. However, the metal leaching in metal-based catalysts and the low activity of non-metallic materials restrict ROS production. In this work, the purpose was achieved by loading a small amount of spinel CuFe₂O₄ onto porous carbon nitride substrate. The synthesized CuFe₂O₄@O-CN composite first to activate peroxymonosulfate (PMS), which produce a plenty of ROS (•OH, SO₄•^- and ¹O₂) for organics removal, leading to highly oxidation for diverse organics. Through the comparative analysis of the surface composition before and after reaction, we found that the interface multi-electron transfer routs, including surface Cu(II)/Cu(I), Fe(III)/Fe(II) and their cross interaction, participated in the redox cycle, giving rise to the rapid and massive production of ROS, so that DMPO and TEMP were instantly oxidized in electron paramagnetic resonance (ESR) detection. Importantly, the carrier of porous O-CN, which acted as the electron transfer mediator, not only favors PMS adsorption via surface -OH, but also facilitates the conversion between different metal species. As a result, the CuFe₂O₄@O-CN/PMS system can remove 99.1% BPA and achieve 52.6% mineralization under optimized conditions. Thus, this study not only sheds light on the tailored design of heterogeneous catalyst for organics removal and elucidates the interfacial catalytic mechanisms for PMS activation.

Magnetized Activated Carbon Synthesized from Pomegranate Husk for Persulfate Activation and Degradation of 4-Chlorophenol from Wastewater

The compound 4-chlorophenol (4-CP) is known to be a highly toxic compound having harmful effects on human health and the environment. To date, the removal of 4-CP by advanced oxidation processes (AOPs) has attracted tremendous attentions. The persulfate-based AOPs show higher oxidation, better selectivity, wider pH range, and no secondary pollution compared to the traditional Fenton-based AOPs. Carbon materials with low cost and chemical stability are useful for the activation of persulfate (PS) to produce reactive species. Herein, we magnetized activated carbon synthesized from pomegranate husk (MPHAC). By using 4-CP as a model organic pollutant, tests of the activation of PS via MPHAC for the removal of 4-CP were performed. Batch processes were carried out to study the influence of different parameters (initial solution pH, catalyst dose, PS dose, and initial 4-CP concentration) on the adsorption of 4-CP on PHAC with ferric oxide (Fe3O4-PHAC). The results show that under the obtained optimal conditions (MPHAC dose: 1250 mg/L, PS dose: 350 mg/L, solution pH 5, an initial 4-CP concentration of 100 mg/L, and a contact time of 60 min), a 4-CP removal factor of 99.5% was reached by the developed MPHAC/PS system. In addition, it was found that reusing MPHAC in five successive cycles is feasible because the catalyst in the last cycle kept exhibiting a high potential for 4-CP absorption, indicating the economically viable procedure. Therefore, this study provides a comprehensive understanding on the degradation of 4-CP by the magnetized activated carbon persulfate system.

Regulation of growth temperature on structure, magnetism of epitaxial FeCo2O4 films

Epitaxial FeCo2O4 films were grown by pulsed laser deposition on Al2O3 (0001) substrates at different growth temperatures in this work.

Degradation of 2,4-dichlorophenol by cathodic microarc plasma electrolysis: characteristics and mechanisms

In this work, we used cathodic microarc plasma electrolysis (CMPE) to degrade 2,4-dichlorophenol (2,4-DCP) in simulated wastewater. By investigating and comparing the removal efficiencies and chemical oxygen demand (COD) during the degradation process, higher bath voltage and alkaline condition were considered as more suitable for the 2,4-DCP decomposition. Higher initial 2,4-DCP concentration was attributed to the increase in the utilisation of the energy input. The plasma characteristics during CMPE were studied by optical emission spectroscopy (OES). It was found that the 2,4-DCP directly participated in the plasma discharge process. Furthermore, by studying the evolution of intermediate products at different experimental parameters, it was found that the existence of Cl^- played an important role in the opening of benzene ring, which activated the ortho-substitutions of hydroxyl, meanwhile accelerated the p-substitutions. The instantaneous high temperature and high pressure and the Cl^- that were generated and driven by cathodic plasma made the decomposition of 2,4-DCP much quicker.

Preparation and Magnetic Properties of Cobalt-Doped FeMn2O4 Spinel Nanoparticles

Mixed-metal oxide nanoparticles have attracted great scientific interest since they find applications in many fields. However, the synthesis of size-controlled and composition-tuned mixed-metal oxide nanoparticles is a great challenge that complicates their study for practical application. In this study, Co-doped FeMn₂O₄ nanoparticles were synthesized by the solvothermal method in which the crystallization was carried out under autogenous pressure at temperatures of 190 °C for 24 h. The influence of Co doping on the evolution of the structural and magnetic properties was investigated by various methods. It was found from XRD data that crystallite size decreases from 9.1 to 4.4 nm with the increase in Co content, which is in good agreement with the results of TEM. Based on the results of magnetic measurements, it was found that the saturation magnetization first increases with an increase in the cobalt content and reaches its maximum value at x = 0.4, and a further increase in x leads to a decrease in the saturation magnetization. The influence of cation redistribution on the observed changes has been discussed.

Advances in Electrochemical and Catalytic Performance of Nanostructured FeCo2 O4 and Its Composites

It is well established that the excessive and uncontrolled use of fossil fuels and organic chemicals have put a risk to the earth's environment and the life that sustains within it. Carbon-free, sustainable, alternative energy technologies have therefore become the prime focus of current research. Smart inorganic materials have emerged as the potential solution to suffice energy needs and remediate the organic pollutants discharged to the environment. One such promising, versatile material is FeCo₂ O₄ which has gained immense research interest in the present decade due to its high efficiency and performance in energy and environmental applications. Innovative material design strategies involving the interplay of nanostructured morphology, chemical composition, redox surface states, and defect engineering have significantly enhanced both electrochemical and catalytic properties of FeCo₂ O₄ . Therefore, this review article aims to provide the first-ever comprehensive account of the latest research and developments in design-synthesis strategies, characterization techniques, and applications of nanostructured FeCo₂ O₄ and its composites in various electrochemical as well as catalytic applications. A detailed account of the nanostructured FeCo₂ O₄ and its composites in various energy storage and conversion devices such as supercapacitors (SCs), batteries, and fuel cells has been presented. Furthermore, a special section has been devoted to highlight the role of FeCo₂ O₄ in enhancing the sluggish reaction kinetics of oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in water splitting application. This review also highlights the role of nanostructured FeCo₂ O₄ in photocatalytic waste water treatment, gas sensing, and dual-phase membrane technologies wherein FeCo₂ O₄ has demonstrated promising performance.

Recent advances in cobalt-activated sulfate radical-based advanced oxidation processes for water remediation: A review

Sulfate radical-based advanced oxidation processes (SR-AOPs) have attracted increasing attention for the degradation of organic contaminants in water. The oxidants of SR-AOPs could be activated to generate different kinds of reactive oxygen species (ROS, e.g., hydroxyl radicals (OH), sulfate radicals (SO₄^-), singlet oxygen (¹O₂), and superoxide radicals (O₂^-)) by various catalysts. As one of the promising catalysts, cobalt-based catalysts have been extensively investigated in catalytic activity and stability during water remediation. This article mainly summarizes recent advances in preparation and applications of cobalt-based catalysts on peroxydisulfate (PDS)/peroxymonosulfate (PMS) activation since 2016. The review covers the development of homogeneous cobalt ions, cobalt oxides, supported cobalt composites, and cobalt-based mixed metal oxides for PDS/PMS activation, especially for the latest nanocomposites such as cobalt-based metal-organic frameworks and single-atom catalysts. This article also discussed the activation mechanisms and the influencing factors of different cobalt-based catalysts for activating PDS/PMS. Finally, the future perspectives on the challenges and applications of cobalt-based catalysts are presented at the end of this paper.

Uncertainty and misinterpretation over identification, quantification and transformation of reactive species generated in catalytic oxidation processes: A review

The identification of reactive radical species using quenching and electron paramagnetic resonance (EPR) tests has attracted extensive attention, but some mistakes or misinterpretations are often present in recent literature. This review aims to clarify the corresponding issues through surveying literature, including the uncertainty about the identity of radicals in the bulk solution or adsorbed on the catalyst surface in quenching tests, selection of proper scavengers, data explanation for incomplete inhibition, the inconsistent results between quenching and EPR tests (e.g., SO₄^•- is predominant in quenching test while the signal of ^•OH predominates in EPR test), and the incorrect identification of EPR signals (e.g., SO₄^•- is identified by indiscernible or incorrect signals). In addition, this review outlines the transformation of radicals for better tracing the origin of radicals. It is anticipated that this review can help in avoiding mistakes while investigating catalytic oxidative mechanism with quenching and EPR tests.

Clinoptilolite mediated activation of peroxymonosulfate through spherical dispersion and oriented array of NiFe2O4: Upgrading synergy and performance

Inspired by the features of both transition metal oxide and natural clinoptilolite (flaky structure with suitable pore diameter and open skeleton structure), we adopted a robust strategy by immobilization of nickel ferrite nanoparticles (NiFe₂O₄) on the clinoptilolite surface via typical citric acid combustion method. The hybrid catalyst exhibited enhanced peroxymonosulfate (PMS) activation efficiency and bisphenol A (BPA) degradation performance. Calculated by effective equivalent of NiFe₂O₄, it is found that the reaction rate constant (k) of NiFe₂O₄/clinoptilolite/PMS system (0.1859 min^-1) was 11.9 times higher than that of bare NiFe₂O₄/PMS system (0.0156 min^-1), which demonstrated that catalyst would be conjugated to PMS or contaminant efficiently and renders the rapid degradation and mineralization in the presence of clinoptilolite. After comprehensive characterization analysis and DFT simulations, natural mineral carrier effect (i.e. decreased crystalline size, increased oxygen vacancy content, etc.), abundant surface-bonded and structural hydroxyl groups as well as effective bonding with iron or nickel ions charged for the potential activation mechanism of PMS by NiFe₂O₄/clinoptilolite composite. And it is indicated that not only ^•OH and SO₄^•-, but also ¹O₂ was involved into series reactions. Overall, this study put forward a green and promising technology for high-toxic wastewater treatment.

Synergistic activation of peroxymonosulfate via in situ growth FeCo2O4 nanoparticles on natural rectorite: Role of transition metal ions and hydroxyl groups

Developing low-cost, high-efficiency catalysts for advanced oxidation processes remain a key issue for the degradation of organic pollutants. In this study, a novel FeCo₂O₄/rectorite composite was synthesized via a facile combustion process and employed to activate peroxymonosulfate (PMS) for dealing with atrazine (ATZ). The addition of rectorite could result in higher specific surface area, smaller pore size and more hydroxyl groups, which were beneficial to enrich pollutants to the adsorption sites and provide sufficient reactive sites. After meticulous evaluation, the degradation efficiency of FeCo₂O₄/rectorite composite towards ATZ exhibited improved PMS activation efficiency which was about 2.6 times than that of pure FeCo₂O₄. Based on the characterization results, the sulfate radicals and hydroxyl radicals were considered to be the main free radicals which were involved into the circulation of Co(II)-Co(III)-Co(II) as well as the oxidation of ≡Fe(II), which was responsible for the remarkable catalytic efficiency. In addition, the chemical stability and superior catalytic performance of FeCo₂O₄/rectorite should also be attributed to the chemical combination between metal ions and the surface hydroxyl groups of rectorite. Overall, these findings are beneficial for understanding the mechanism of PMS activation by natural mineral-based catalysts and contributing to the practical application of sulfate-based technology for organic wastewater treatment.

Activation of persulfate by heterogeneous catalyst ZnCo2O4–RGO for efficient degradation of bisphenol A

A nanocomposite, reduced graphene oxide (RGO) modified ZnCo2O4 (ZnCo2O4–RGO) was synthesized via one-step solvothermal method for activating persulfate (PS) to degrade bisphenol A (BPA). The morphology and structure of the nanocomposite were identified by X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. RGO provides nucleation sites for ZnCo2O4 to grow and inhibits the agglomeration of the nanoparticles. The influence of different reaction conditions on the oxidation of BPA catalyzed by ZnCo2O4–RGO was investigated, including the content of RGO, the dosage of catalyst, the concentration of humic acid (HA), anions in the environment, the reaction temperature, and pH. BPA can be totally degraded within 20 min under optimized reaction conditions. The presence of HA, Cl−, and NO3− only has a slight effect on the oxidation of BPA, whereas the presence of either H2PO4− or HCO3− can greatly inhibit the reaction. ZnCo2O4–RGO shows good cycling stability and practical application potential. A reaction mechanism of the degradation of BPA was also explored.

Perovskite and Spinel Catalysts for Sulfate Radical-Based Advanced Oxidation of Organic Pollutants in Water and Wastewater Systems

Since environmental pollution by emerging organic contaminants is one of the most important problems, gaining ground year after year, the development of decontamination technologies of water systems is now imperative. Advanced oxidation processes (AOPs) with the formation of highly reactive radicals can provide attractive technologies for the degradation of organic pollutants in water systems. Among several AOPs that can be applied for the formation of active radicals, this review study focus on sulfate radical based-AOPs (SR-AOPs) through the heterogeneous catalytic activation of persulfate (PS) or peroxymonosulfate (PMS) using perovskite and spinel oxides as catalysts. Perovskites and spinels are currently receiving high attention and being used in substantial applications in the above research area. The widespread use of these materials is based mainly in the possibilities offered by their structure as it is possible to introduce into their structures different metal cations or to partially substitute them, without however destroying their structure. In this way a battery of catalysts with variable catalytic activities can be obtained. Due to the fact that Co ions have been reported to be one of the best activators of PMS, special emphasis has been placed on perovskite/spinel catalysts containing cobalt in their structure for the degradation of organic pollutants through heterogeneous catalysis. Among spinel materials, spinel ferrites (MFe2O4) are the most used catalysts for heterogeneous activation of PMS. Specifically, catalysts with cobalt ion in the A position were reported to be more efficient as PMS activators for the degradation of most organic pollutants compared with other transition metal catalysts. Substituted or immobilized catalysts show high rates of degradation, stability over a wider pH area and also address better the phenomena of secondary contamination by metal leaching, thus an effective method to upgrade catalytic performance.

Rosmarinic acid enhanced Fe(III)-mediated Fenton oxidation removal of organic pollutants at near neutral pH

In this study, we reported that the presence of rosemary acid (RA) could strongly enhance the Fe(III)-mediated Fenton oxidation of 2,4-DCP as the model contaminant at near neutral pH. This enhancement was verified by the strong chelating and reducing ability of RA, which could prevent ion precipitation and accelerate the Fe³⁺/Fe²⁺ cycle. Radical quenching experiments and electron paramagnetic resonance confirmed the existence and roles of hydroxyl radicals in the Fe³⁺/RA/H₂O₂ system. Lot size optimized experiments were executed to achieve efficient 2,4-DCP degradation (99.93%) under the optimum conditions of 100 μmol/L Fe³⁺, 100 μmol l/L RA and 8 mmol/L H₂O₂ within 60 min. In addition, co-existing metal ions, inorganic anions and natural organic matters were proved that they could inhibit removal efficiency and rate at varying degrees. Total organic carbon and chloride ion measurements were employed to probe the mineralization of organic matters (including RA and 2,4-DCP). This study provides a new modified Fenton system to enhance the oxidation removal of refractory organics in water and will enrich the understanding on effective H₂O₂ activation at neutral pH.

Facile synthesis of graphene-based hyper-cross-linked porous carbon composite with superior adsorption capability for chlorophenols

In this work, we proposed a green and cost-effective method to prepare a graphene-based hyper-cross-linked porous carbon composite (GN/HCPC) by one-pot carbonization of hyper-cross-linked polymer (HCP) and glucose. The composite combined the advantages of graphene (GN) and hyper-cross-linked porous carbon (HCPC), leading to high specific surface area (396.93 m²/g) and large total pore volume (0.413 cm³/g). The resulting GN/HCPC composite was applied as an adsorbent to remove 2,4-dichlorophenol (2,4-DCP) from aqueous solutions. The influence of different solution conditions including pH, ionic strength, contact time, system temperature and concentration of humic acid was determined. The maximum adsorption capacity of GN/HCPC composite (calculated by the Langmuir model) could reach 348.43 mg/g, which represented increases of 43.6% and 13.6% over those of the as-prepared pure GN and HCPC, respectively. The Langmuir model and pseudo-second-order kinetic model were found to fit well with the adsorption process. Thermodynamic experiments suggested that the adsorption proceeded spontaneously and endothermically. In addition, the GN/HCPC composite showed high adsorption performance toward other organic contaminants including tetracycline, bisphenol A and phenol. Measurement of the adsorption capability of GN/HCPC in secondary effluent revealed a slight decrease over that in pure water solution. This study demonstrated that the GN/HCPC composite can be utilized as a practical and efficient adsorbent for the removal of organic contaminants in wastewater.

Synergistic coupling Co3Fe7 alloy and CoFe2O4 spinel for highly efficient removal of 2,4-dichlorophenol by activating peroxymonosulfate

Efficient wastewater restoration depends on the robustness and capability of the catalyst to promote sophisticated decontamination technologies. In this study, Co₃Fe₇-CoFe₂O₄ nanoparticles (NPs) prepared by facile pyrolysis were completely characterized and used to decompose 2,4-dichlorophenol (2,4-DCP). Furthermore, the catalytic performance and relevant mechanisms involved in the activation of peroxymonosulfate (PMS) were also investigated. The optimal conditions were achieved at the catalyst loading of 0.05 g L^-1, PMS dosage of 1.26 g L^-1, and pH of 7.7 through the response surface methodology by using the Box-Behnken design model. Under optimal conditions, 97.1% efficiency of 2,4-DCP removal was obtained within 30 min. Moreover, the quenching experiments and electron paramagnetic resonance result indicated that sulfate (SO₄^•-) and hydroxyl (HO^•) radicals were considered as the dominant reactive oxygen species, which resulted in the effective removal of 2,4-DCP in the Co₃Fe₇-CoFe₂O₄/PMS system. Moreover, Co₃Fe₇-CoFe₂O₄ showed efficient catalytic performance in continuous five runs and exhibited less metal leaching of 0.052 and 0.036 mg L^-1 for Co and Fe species, respectively. Furthermore, no considerable change was observed in the structural characteristics of the fresh and used Co₃Fe₇-CoFe₂O₄ catalytic system. The above-mentioned results indicated that the synergistic effects between Co₃Fe₇ alloy and CoFe₂O₄ spinel not only significantly improved the activity and long-term durability of the catalyst, but also accelerated the Co³⁺/Co²⁺ and Fe³⁺/Fe²⁺ redox cycles. Overall, the Co₃Fe₇-CoFe₂O₄/PMS system provides a novel advanced oxidation approach to further develop multifunctional transition metal-based nanomaterials responsible for producing surface-bound radicals and enhancing the remediation of refractory pollutants in the environmental application.

Activation of peroxymonosulfate by CoFe2O4 loaded on metal-organic framework for the degradation of organic dye

The magnetic composite CoFe₂O₄/ZIF-8 based on metal organic framework (MOF) with high specific surface area and high activity was synthesized by solvothermal method. The prepared catalysts were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), vibration sample magnetometer (VSM) and N₂ adsorption-desorption isotherms, respectively. After characterization, CoFe₂O₄/ZIF-8 was applied to heterogeneous activation of peroxymonosulfate (PMS) for degrading methylene blue (MB). The result showed that the 0.075-CoFe₂O₄/ZIF-8 sample had the excellent catalytic activity. After catalytic reaction for 60 min, the degradation efficiency of MB (20 mg/L) reached about 97.9% at room temperature of 20 °C. The quenching experiment and electron paramagnetic resonance (EPR) analysis indicated that SO₄^- and OH radicals were the main active species in MB degradation. Meanwhile, the possible MB degradation mechanism was proposed. After four catalytic cycles, the degradation efficiency of MB has not been greatly reduced, indicating the practical application potential of CoFe₂O₄/ZIF-8 in water pollution cleanup.

Heterogeneous activation of persulfate for the degradation of bisphenol A with Ni2SnO4–RGO

The possible reaction mechanism of the activation of persulfate by Ni₂SnO₄–RGO for the degradation of BPA.

Interactions between chlorophenols and peroxymonosulfate: pH dependency and reaction pathways

A non-radical reaction between peroxysulfates and phenolic compounds, as important structural moieties of natural organic matters, has been reported recently, implying new opportunities for environmental remediation without need for catalyst or energy input. However, this approach seems to be ineffective for halogenated aromatic compounds, an important disinfection by-products (DBPs). Here, we shed light on the interactions between peroxymonosulfate (PMS) and chlorophenols and the influential factors. The results show that the chlorophenols transformation kinetics were highly dependent on the solution pH and chlorophenol species: raising the pH significantly accelerated the chlorophenols degradation, and at alkaline pH the removal rates of different chlorophenols were in the order of trichlorophenol > dichlorophenol > chlorophenol > tetrachlorophenol. The faster degradation of pollutants with more chlorine groups was mainly due to their relatively higher dissociation degree, which favors a direct pollutant-PMS interaction to generate radicals for their degradation. The chlorophenol degradation intermediate (i.e. benzoquinone) further mediated the generation of singlet oxygen at alkaline pH, thereby contributing to accelerated pollutant removal. The slower degradation of tetrachlorophenol than other chlorophenols was likely due to its strong electrostatic epulsion to PMS which restricted the reaction. Our work unveils the chlorophenols degradation mechanisms in PMS reaction system, which may facilitate a better understanding and optimization of advanced oxidation processes for pollution control to reduce potential DBPs accumulation.

Activation of peroxymonosulfate by magnetic carbon supported Prussian blue nanocomposite for the degradation of organic contaminants with singlet oxygen and superoxide radicals

In order to develop efficient and green catalyst for organic pollutants removal, magnetic carbon supported Prussian blue nanocomposite Fe₃O₄@C/PB was prepared for the first time. The performance of Fe₃O₄@C/PB in activating peroxymonosulfate (PMS) for the degradation of 2,4-dichlorophenol (2,4-DCP) was investigated. 2,4-DCP could be effectively degraded under the "Fe₃O₄@C/PB + PMS" system within a broad pH range of 2-9. Without pH adjustment (pH 3), 2,4-DCP (20 mg/L) was completely degraded in 50 min along with a 70% removal of TOC; while the required time for complete degradation of 2,4-DCP was shortened to 40 min under initial solution pH at 7. Fe₃O₄@C/PB could also activate PMS for the degradation of phenol, Acid Orange II, Reactive brilliant red X-3B, Rhodamine B and Methylene blue. The degradation rates higher than 95% could be achieved for all these contaminants within the time scale of 15-60 min. The studies of radical-quenching and electron paramagnetic resonance demonstrated that singlet oxygen (¹O₂) and superoxide radicals (O₂^-), rather than sulfate (SO₄^-) and hydroxyl (OH) radicals, were the dominant species responsible for the oxidation of organic pollutants. The plausible mechanism of the catalytic degradation was proposed and the enhanced activity of Fe₃O₄@C/PB was assumed to be related to the increased electron transfer owing to the synergic effect between the magnetic carbon and the mixed-valence units in PB. Fe₃O₄@C/PB is promising in wastewater treatment owing to its high efficiency, excellent stability and reusability, environmental friendliness and magnetic separability.

A novel combination of bioelectrochemical system with peroxymonosulfate oxidation for enhanced azo dye degradation and MnFe2O4 catalyst regeneration

Advanced oxidation process (AOP) based on peroxymonosulfate (PMS) activation was established in microbial fuel cell (MFC) system with MnFe₂O₄ cathode (MFC-MnFe₂O₄/PMS) aimed to enhance azo dye degradation and catalyst regeneration. The effects of loading amount of MnFe₂O₄ catalyst, applied voltage, catholyte pH and PMS dosage on the degradation of Orange II were investigated. The stability of the MnFe₂O₄ cathode for successive PMS activation was also evaluated. The degradation of Orange was accelerated in the MFC-MnFe₂O₄/PMS with apparent degradation rate constant increased to 1.8 times of that in the MnFe₂O₄/PMS control. A nearly complete removal of Orange II (100 mg L^-1) was attained in the MFC-MnFe₂O₄/PMS under the optimum conditions of 2 mM PMS, 10 mg cm^-2 MnFe₂O₄ loading, pH 7-8 and 480 min reaction time. MFC driven also extended the longevity of the MnFe₂O₄ catalyst for PMS activation due to the in-situ regeneration of ≡Mn²⁺ and ≡Fe²⁺ through accepting electrons from the cathode, and over 80% of Orange II was still removed in the 7^th run. Additionally, the MFC-MnFe₂O₄/PMS system could recover electricity during Orange II degradation with a maximum power density of 206.2 ± 3.1 mW m^-2. PMS activation by MnFe₂O₄ was the primary pathway for SO₄^- generation, and SO₄^- based oxidation was the primary mechanism for Orange II degradation. MFCs driven coupled with PMS activated AOP systems provides a novel strategy for efficient and persistent azo dye degradation.

Application of nickel foam-supported Co3O4-Bi2O3 as a heterogeneous catalyst for BPA removal by peroxymonosulfate activation

Nickel foam (NF)-functionalized Co₃O₄-Bi₂O₃ nanoparticles (CBO@NF) synthesized using a facile one-step microwave-assistant method were employed as catalysts to activate peroxymonosulfate (PMS) with bisphenol A (BPA) as the target pollutant. The crystallinity, morphology, and chemical valence state of the synthesized CBO@NF were analyzed using XRD, SEM, and XPS, respectively. Moreover, effects of the preparation parameters, including the calcination temperature and calcination time as well as the loading dosage, were evaluated in detail. A degradation efficiency of 95.6% was achieved within 30 min with the optimal degradation system. The CBO@NF/PMS system shows great catalytic activity in a pH range from 3.0 to 11.0. The stability and reusability of the CBO@NF supported catalyst was evaluated through a recycling experiment. In addition, the possible degradation mechanism was also explored using a quenching experiment and electron paramagnetic resonance (EPR) detection. The result shows that both the surface-bound SO₄^- and OH play significant roles during the degradation process, where the electron transfer of Co²⁺/Co³⁺, Bi³⁺/Bi⁵⁺, and Ni²⁺/Ni³⁺ realizes the sustained regeneration of the active radicals. This work provides new insight for the practical applications of sulfate radical-based advanced oxidation processes (SR-AOPs) in wastewater treatment.

Quaternary ferrites by batch and continuous flow hydrothermal synthesis: a comparison

Crystalline spinel quaternary ferrites M_xZn_1−xFe₂O₄ (M = Co, Ni) were synthesised through two synthetic routes: conventional batch and continuous flow hydrothermal synthesis.

Catalytic degradation of diclofenac from aqueous solutions using peroxymonosulfate activated by magnetic MWCNTs-CoFe3O4 nanoparticles

CoFe₃O₄ nanoparticles supported on multi-walled carbon nanotubes (MWCNTs-CoFe₃O₄) were synthesized by the co-precipitation method as a novel catalyst for degradation of diclofenac (DCF). The comparative experiments indicated that MWCNTs-CoFe₃O₄ has a better catalytic activity in degradation of DCF and activation of peroxymonosulfate (PMS) compared to other catalytic systems. This can be attributed to the interaction of MWCNTs with CoFe₃O₄ in accelerating the absorption process and activating the PMS (E_a = 22.93 kJ mol⁻¹). The removal efficiencies of DCF and total organic carbon (TOC) were 99.04% and 50.11%, under optimum conditions, e.g., pH of 7, PMS dosage of 4 mM, DCF concentration of 30 mg L⁻¹, catalyst dosage of 500 mg L⁻¹, and reaction time of 120 min. The oxidation of DCF was fitted by the pseudo-first-order kinetic model and the constant rate was increased by increasing the pH, temperature, dosage of PMS and catalyst. The production of reactive species was studied using scavengers such as TBA and ethanol and the results showed that sulfate radical is the reactive species responsible for the degradation of DCF. The MWCNTs-CoFe₃O₄ catalyst showed high stability and reusability based on five successful repeated reactions, X-ray diffraction and energy dispersive X-ray spectroscopy analysis. Based on the intermediates detected by gas chromatography-mass spectrometry (GC-MS), the possible pathways for DCF catalytic oxidation were proposed. The results explained that the PMS/MWCNTs-CoFe₃O₄ system is a promising method for treating DCF solution due to high efficiency, good reusability of catalyst and greater PMS activation.

The MWCNTs-CoFe₃O₄ as a novel catalyst showed high catalytic activity in activation of proxymonosulfate for degradation of diclofenac.

Optimization of the catalytic activity of a ZnCo2O4 catalyst in peroxymonosulfate activation for bisphenol A removal using response surface methodology

An effective peroxymonosulfate activator, ZnCo₂O₄, was synthesized through a microwave-assisted method. According to response surface methodology (RSM) using Box-Behnken design (BBD), the effects of four parameters, microwave temperature, microwave time, calcination time and calcination temperature, were investigated, and the results show that both the microwave temperature and calcination temperature have a great influence on the catalytic activity during the preparation process. In addition, a quadratic model is valid for computing and predicting the observed responses. The characteristics of the synthesized ZnCo₂O₄ catalyst were analyzed with various equipments. The results show that the ZnCo₂O₄ nanosheets are cubic crystals with a spinel structure and a high surface area of 105.90 m²‧g^-1. Under the conditions of [ZnCo₂O₄] = 0.2 g‧L^-1 and [PMS]/[BPA]_molar = 2.0, the bisphenol A degradation efficiency reaches 99.28% within 5 min in the ZnCo₂O₄/PMS system. ZnCo₂O₄ possesses great stability and reusability according to recycling experiments. In addition, the possible active radical species were confirmed through quenching experiments and EPR detection, indicating that surface-bound SO₄^- and OH play vital roles during the degradation process.

Implementation of martite nanoparticles prepared through planetary ball milling as a heterogeneous activator of oxone for degradation of tetracycline antibiotic: Ultrasound and peroxy-enhancement

The aim of the present study was to employ martite nanoparticles synthesized through planetary ball milling instead of conventional sources of iron for the activation of Oxone in order to decompose tetracycline (TC) antibiotic in the aquatic phase. Accordingly, martite nanoparticles-activated Oxone exhibited a remarkable improvement in degrading TC molecules up to 87%. The results indicated an increased decomposition rate of TC with increasing Oxone concentration, martite nanoparticles dosage, and initial pH. In the absence of ultrasound, the decomposition rate of TC was 0.0481 min^-1 within 30 min, while the implementation of ultrasound at 320 W and addition of hydrogen peroxide at 40 mM led to increase in the decomposition rate up to 0.0770 and 0.0907 min^-1, respectively. The presence of carbonate and even persulfate ions suppressed the decomposition rate. Inversely, the addition of chloride and carbon tetrachloride enhanced the reactor performance in terms of TC degradation. Within four consecutive experimental runs, only 10.8% was dropped in the decomposition rate, indicating the appropriate reusability potential of martite nanoparticles. The results confirmed the appropriate ability of the treatment process in degrading and mineralizing the target pollutant but a longer exposure time is required for an efficient mineralization.