Applications and characteristics of Fe-Mn binary oxides for Sb(V) removal in textile wastewater: Selective adsorption and the fixed-bed column study

Evaluation of a granular Cu-modified chitosan biocomposite for sustainable sulfate removal from aqueous media: A batch and fixed-bed column study

Adsorption-based treatment of sulfate contaminated water sources present challenges due to its favourable hydration characteristics. Herein, a copper-modified granular chitosan-based biocomposite (CHP-Cu) was prepared and characterized for its sulfate adsorption properties at neutral pH via batch equilibrium and fixed-bed column studies. The CHP-Cu adsorbent was characterized by complementary methods: spectroscopy (IR, Raman, X-ray photoelectron), thermal gravimetry analysis (TGA) and pH-based surface charge analysis. Sulfate adsorption at pH 7.2 with CHP-Cu follows the Sips isotherm model with a maximum adsorption capacity (407 mg/g) that exceeds most reported values of granular biosorbents at similar conditions. For the dynamic adsorption study, initial sulfate concentration, bed height, and flow rate were influential parameters governing sulfate adsorption. The Thomas and Yoon-Nelson models yield a sulfate adsorption capacity (146 mg/g) for the fixed bed system at optimized conditions. CHP-Cu was regenerated over 5 cycles (33 % to 31 %) with negligible Cu-leaching. The adsorbent also displays excellent sulfate uptake properties, regenerability, and sustainable adsorbent properties for effective point-of-use sulfate remediation in aqueous media near neutral pH (7.2). This sulfate remediation strategy is proposed for other oxyanion systems relevant to contaminated environmental surface and groundwater resources.

Facile synthesis of δ-MnO2 biotemplated by waste tobacco stem-silks for enhanced removal of Sb(III)

The elimination of antimony pollution has attracted increasing concerns because of its high toxicity to human health and the natural environment. In this work, biomimetic δ-MnO2 was synthesized by using waste tobacco stem-silks as biotemplate (Bio-δ-MnO2) and used in the capture of Sb(III)from aqueous solution. The tobacco stem-silks not only provided unique wrinkled morphologies but also contained carbon element self-doped into the resulting samples. The maximum Sb(III) adsorption capacity reached 763.4 mg∙g -1, which is 2.06 times higher than δ-MnO2 without template (370.0 mg∙g -1), 4.53 times than tobacco stem-silks carbon (168.5 mg∙g -1), and 10.39 times than commercial MnO2 (73.5 mg∙g -1), respectively. The isotherm and kinetic studies indicated that the adsorption behavior was consistent with the Langmuir isotherm model and the pseudo-second-order kinetic equation. As far as we are aware, the adsorption capacity of Bio-δ-MnO2 is much higher than that of most Sb(III) adsorbents. FT-IR, XPS, SEM, XRD, and Zeta potential analyses showed that the main mechanism for the adsorption of Sb(III) by Bio-δ-MnO2 includes electrostatic attraction, surface complexation, and redox. Overall, this study provides a new sustainable way to convert agricultural wastes to more valuable products such as biomimetic adsorbent for Sb(III) removal in addition to conventional activated carbon and biochar.

Comparative Sb(V) removal efficacy of different iron oxides from textile wastewater: effects of co-existing anions and dye compounds

Elevated Sb(V) concentration in textile wastewater is a growing environmental concern worldwide and has received wider attention in recent years. Iron oxides possess appealing characteristics as efficient and cost-effective adsorbents in large-scale applications. In the present study, Sb(V) adsorption capacity of α-Fe2O3, γ-Fe2O3, and Fe3O4 was compared under experimental conditions close to the practical textile wastewater treatment. Results demonstrated that α-Fe2O3 performed better under different pH values, reaction times, dye compounds, and co-existing ions as compared to γ-Fe2O3 and Fe3O4, and the adsorption equilibrium was achieved within 8 h. Sb(V) adsorption is found to be highly pH dependent, and higher removal was achieved in lower pH, indicating the involvement of electrostatic interactions. The pHpzc value of α-Fe2O3 was 7.15, which favored Sb(V) adsorption in practical wastewater having neutral pH value (pH ~ 7). Pseudo-first- and pseudo-second-order described the data and the simulated values of qe fitted well with the experimental values, indicating that pseudo-second-order model described the adsorption kinetics better with R2 (> 0.95) higher than of pseudo-first-order plots. The Langmuir and Freundlich models both described well the sorption data of all the adsorbents, where the R2 values were > 0.90 with a better fit in the Freundlich model for α-Fe2O3, suggesting that the adsorbent has heterogeneous surface characteristics. Similarly, characterizations revealed that the specific surface area, pore volume, and hydroxyl group content in α-Fe2O3 were higher than others, making it easier for contaminants to bind on to the active sites. Furthermore, the effect of dyes and co-existing anions on Sb(V) adsorption was negligible, except for SO42-, CO32-, and PO43- by the formation of inner-sphere complexes with iron oxides through competitive adsorption with [Sb(OH)6]-. Findings from the present study suggested that α-Fe2O3 effectively reduced Sb(V) in textile wastewater and could be a promising alternative for practical textile wastewater treatment.

Antimony (Sb) pollution control by coagulation and membrane filtration in water/wastewater treatment: A comprehensive review

Antimony (Sb) pollution in the water environment caused by the large-scale mining of Sb ore and the wide use of Sb-containing products seriously endangers human health and poses a great threat to the ecological environment. Coagulation is one of the most cost-effective technologies for Sb pollution control in water/wastewater treatment and has been widely used. However, a comprehensive understanding of Sb pollution control by coagulation, from fundamental research to practical applications, is lacking. In this work, based on the current status of Sb pollution in the water environment, a critical review of the Sb removal performance and mechanism by coagulation and related combined processes was carried out. The influencing factors of Sb removal performance by coagulation are introduced in detail. The internal mechanisms and improvement strategies of Sb removal by oxidation/reduction-coagulation and coagulation-membrane filtration technologies are emphasized. Moreover, given the development of Sb-removing coagulants and the resource utilization of Sb-containing sludge, future perspectives of coagulation for Sb removal are discussed. As the first review in this field, this work will illuminate avenues of basic research and practical applications for Sb and Sb-like pollution control in water/wastewater treatment.

Insights into the correlation between different adsorption/oxidation/catalytic performance and physiochemical characteristics of Fe-Mn oxide-based composites

Fe-Mn oxide-based composites have been widely used in the solidification of heavy metals or the removal of organic pollutants, which can not only show excellent adsorption/oxidation performance, but also show catalytic activity for common oxidants. At present, the correlation between adsorption/oxidation/catalytic performance and physicochemical characteristics of these composites, and the underlying mechanisms are still unclear. Therefore, the main purpose of this review is to disclose the internal relationship between the physicochemical properties of Fe-Mn oxide-based composites and the pollutant removal performance. From the perspective of crystal phase, the basic units of Fe-Mn oxide composites are divided into Fe-Mn binary oxide (FMBO) and spinel MnFe₂O₄, and the two species were discussed separately in most chapters. The selected physicochemical properties mainly include the type of Fe-Mn oxide composites, surface-to-volume ratio, pore volume, pH_pzc, crystal type, surface functional groups. Because the physicochemical properties that determine how effective Fe-Mn oxide material is at removing contaminants may differ as it performs different functions, we discussed the above problems under different application scenarios (adsorption, oxidation, and advanced oxidation process). Additionally, internal factor (Fe/Mn mole ratio) and external factors (pH_ini, co-ions and ionic strength) were analyzed, and several common synthetic strategies of these composites were presented.

Effective removal of Sb(V) from aqueous solutions by electrocoagulation with composite scrap iron-manganese as an anode

Improving the removal rate of pentavalent antimony (Sb(V)) by electrocoagulation (EC) is of great significance to the environment. In this paper, the EC with composite scrap iron and manganese filings as an anode (Fe-Mn EC) was investigated for the high-efficiency elimination of Sb(V). The results showed that Fe-Mn EC can enhance the removal of Sb(V) by 11.18-17.36% compared with the traditional iron electrocoagulation (Fe EC). Meanwhile, Sb(V) removal increased with the growth of current concentration as well as Mn content in the anode. However, the Sb(V) removal rate was inhibited when Mn content exceeded 20%. Moreover, the flocs generated during the Fe and Fe-Mn EC (Fe flocs and Fe-Mn flocs) were analyzed both structurally and theoretically using XRD, SEM, BET, and adsorption experiment. The results indicated that the components of Fe-Mn flocs were mostly Mn-substituted FeOOH, which appeared as the structure of nanometer flakes and large internal surface areas. Meanwhile, the Fe-Mn flocs had the ability of much faster Sb(V) adsorption rate; its Sb(V) adsorption capacity was 2.5 times more than that of the Fe flocs. The thermodynamics constants of both Fe and Fe-Mn flocs proved that adsorption was associated with monolayer physical adsorption. To the best of our knowledge, this is the first report of the electrocoagulation with composite scrap iron-manganese as an anode to remove Sb, which provide a new idea and potential technical support for the removal of Sb(V).

Immobilization mechanism of antimony by applying zirconium-manganese oxide in soil

Antimony (Sb) accumulation in soil poses great potential risk to ecological environment, and its mobilization, transformation and bioavailability are controlled by its fractions and species. Hence, it is important to develop functional materials with both adsorption and oxidation that achieve detoxification and control the mobilization of Sb. In this study, the synthesized zirconium‑manganese oxide (ZrMn) could extremely promoted the transformation of antimonite [Sb(III)] to antimonate [Sb(V)], induced the bioavailable Sb shift to well-crystallized (hydr)oxides of Mn and residual fractions, and further reduced mobility and bioavailability Sb in soil. The sorption of ZrMn to Sb(III) and antimonate Sb(V) were affected by interfering ions, and to Sb(III) was a heterogeneous adsorption process. Spectroscopic characterization of XPS and FTIR suggested exchange between the hydroxyl groups and Sb was crucial in its retain and forming an electronegative inner-sphere mononuclear or binuclear bridging compound. The oxidation induced the transformation of Mn species in ZrMn, generated Mn(II) and Mn(III) exposing more reactive sites conducive to oxidation and adsorption, thus Mn oxides has a higher adsorption capacity for Sb(III). However, the Zr oxides of ZrMn presented adsorption rather than oxidation. The application of ZrMn could realize the dual effect of Sb oxidation detoxification and adsorption immobilization in soil, which provided references for Sb contaminated soil remediation.

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.

Review of recently used adsorbents for antimony removal from contaminated water

As prior pollutants, antimony (Sb) and its compounds are carcinogenic to threaten human health. With the development of the industry, various Sb-contained pollutants have been released into nature, thus heavily damaging the ecological environment. Effectively treating Sb-polluted waterbodies is very important and have obtained ever-growing attention. In this review, we have summarized and classified the adsorbents used for removing Sb from water in recent two decades as natural and synthetic biological adsorbents, mineral adsorbents, natural and synthetic carbon materials, metal-based adsorbents, and metal-organic frameworks. We focus on the adsorption behavior of various adsorbents for Sb, including adsorption capacity, isotherms, kinetics, thermodynamics, and effects of environmental factors (e.g., pH, coexisting anions, and natural organic matter). Meanwhile, the involved adsorption mechanisms of Sb by different adsorbents are discussed. Finally, we have outlined the development of adsorbents over the last two decades and summarized the performance characteristics of effective adsorbents, such as the rich functional groups on the surface of the adsorbents (i.e., hydroxyl, carboxyl and amino groups), and the presence of metal elements to coordinate with Sb in (i.e., iron and manganese). We hope this review give enlightenment to design adsorbents for effective removal of Sb.

Removal of Sb(V) from wastewater via siliceous ferrihydrite: Interactions among ferrihydrite, coprecipitated Si, and adsorbed Sb(V)

Although ferrihydrite (Fh) exhibits good Sb(V) adsorption behavior, the instability of its amorphous structure limits its engineering applications. In this study, siliceous ferrihydrite (SiFh) was prepared via coprecipitation to resolve these limitations. X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), and SiFh aging tests revealed that the growth of Fh particles covered with Fe-O-Si links was inhibited while maintaining their amorphous structure. Meanwhile, the XRD patterns indicated that SiFh maintained excellent stability after five adsorption-desorption cycles. During the aging process, the added Si decreased the electrostatic interaction between SiFh and Sb(V), which weakened the affinity between Sb(V) and Fh; however, most of the Sb(V) still entered the Fe lattice after seven days of aging, which was favorable for Sb(V) recovery during reutilization. Furthermore, Sb(V) adsorbed from the simulated textile wastewater onto SiFh had the highest adsorption energy (E_ads), which meant its unstable inner-sphere complexation on the surface of SiFh. Meanwhile, the presence of SO₄^2-, NO₃^-, Ca²⁺, and Mg²⁺ contributed to Sb(V) outer-sphere adsorption. Both of these factors were conducive to Sb(V) desorption. Hence, SiFh is a promising adsorbent owing to its facile preparation process, stability, and optimal regeneration properties.

Simultaneous adsorption and oxidation of Sb(III) from water by the pH-sensitive superabsorbent polymer hydrogel incorporated with Fe-Mn binary oxides composite

In this work, the superabsorbent polymer hydrogel (SPH) of Poly(potassium acrylate-co-acrylamide (PPAA)) incorporated with Fe-Mn binary oxides (FMBOs) was synthesized and used for the removal of Sb(III) from water. Characterization analysis proved that FMBO₃ was successfully encapsulated into the SPH. The Fe/Mn oxide species in the composite SPH comprised FeO(OH), Fe₂O₃, MnO(OH), and MnO₂. The functional groups including N-H, -OH, carboxy as well as Fe atoms were confirmed adsorption sites through ligand exchange and inner-sphere complexes formation. Mn oxides can partially oxidize Sb(III) to Sb(V). Compared with the pseudo-first-order model, the pseudo-second-order model could better describe the adsorption kinetics. And the swelling degree of the composite SPH had a positive impact on the removal rate. The Langmuir-Freundlich model was the most suitable isotherm model to analyze the experimental data. According to thermodynamic parameters, the adsorption process was a spontaneous exothermic reaction. The maximum adsorption capacity of the composite SPH for Sb(III) could be up to 105.59 mg/g at 288 K. In addition, a stable removal rate can be achieved over a wide pH range of 3-10, with little metal leaching even under acidic conditions. Furthermore, coexisting ions and DOM displayed an insignificant influence on the adsorption of Sb(III).

Gentiana straminea Maxim. polysaccharide decolored via high-throughput graphene-based column and its anti-inflammatory activity

Gentiana straminea Maxim. exhibits various biological activities. However, the purification and functions of polysaccharides in Gentiana straminea Maxim. have never been reported. Herein, by proposing a flexible 3D graphene-based decoloration column (3DD column), Gentiana straminea Maxim. polysaccharide (GMP) was high-throughput obtained and its anti-inflammatory activity was investigated. Benefiting from the large macroporous network of 3D NH₂-graphene oxide hydrogel with selective adsorption towards pigments, the 3DD column exhibits high decoloration ratio (96.41%). In addition, the 3DD column provides superior practical functionality as compared to the traditional approaches, which are time-consuming and need toxic solvents, and exhibiting widespread-application for the purification of polysaccharide from other common plant species. More importantly, the decolored GMP as a natural product has promising anti-inflammatory activity on RAW264.7 cells without negative impact on cell viability. Overall, this work reveals a new functional polysaccharides and provides a flexible approach for polysaccharide decoloration, exhibiting a promising prospect for natural polysaccharides in practical application of pharmaceutical.

Insights into adsorptive removal of antimony contaminants: Functional materials, evaluation and prospective

The application of antimony containing compounds in the industry has generated considerable antimony contaminants, which requires to develop methods that are as efficient as possible to remove antimony from water in the view of human health. The adsorption is among the most high-efficiency and reliable purification methods for hazardous materials due to the simple operation, convenient recycling and low cost. Herein, this review systematically summarizes the functional materials that are used to adsorb antimony from water, including metal (oxides) based materials, carbon-based materials, MOFs and molecular sieves, layered double hydroxides, natural materials, and organic-inorganic hybrids. The iron-based adsorbents stand out among these adsorbents because of their excellent performance. Moreover, the interaction between antimony and different functional materials is discussed in detail, while the inner-sphere complexation, hydrogen bond as well as ligand exchange are the main impetus during antimony adsorption. In addition, the desorption methods in adsorbents recycling are also comprehensively summarized. Furthermore, we propose an adsorption capacity balanced evaluation function (ABEF) based on the reported results to evaluate the performance of the antimony adsorption materials for both Sb(III) and Sb(V), as antimony usually has two valence forms of Sb(III) and Sb(V) in wastewater. Another original insight in this review is that we put forward a potential application prospect for the antimony-containing waste adsorbents. The feasible future development includes the utilization of the recycled antimony-containing waste adsorbents in catalysis and energy storage, and this will provide a green and sustainable pathway for both antimony removal and resourization.

Antimonate removal by diatomite modified with Fe-Mn oxides: application and mechanism study

In this study, diatomite coated with Fe-Mn oxides (DFMO) was synthesized through calcination. The adsorption of antimonate (Sb(V)) by DFMO was studied, and environmental factors affecting the adsorption were investigated. The components of DFMO were identified as γ-Fe₂O₃, γ-MnO₂, and SiO₂, in the presence of diatomite covered with nanoscale metal oxides. Batch experiments were carried out to evaluate the antimonate adsorption performance in aqueous solution. Results showed that maximum Sb(V) adsorption capacity of DFMO reached 10.7 mg/g at pH 4, corresponding to 22.2 mg/g per unit metal oxides. Antimonate adsorption occurred on heterogenous surface, following the Freundlich and Pseudo-second order model. Overall, antimonate adsorption was favored at acidic condition due to low point of zero charge. However, when treating electroplating wastewater, neutral pH condition exhibited a higher efficiency than acidic pH, because co-existing ions in electroplating wastewater significantly affects antimony adsorption. Further investigation showed that among different potential co-existing ions, fluoride can strongly inhibit the adsorption of antimonate at 5 mg/L under pH 4. Density functional theory (DFT) analysis confirmed that adsorption energy on DFMO follows: HF < F^- < Sb(OH)₆^-, indicating that fluoride is easier to bind with DFMO compared to antimonate, especially under pH 3.5 at which fluoride exists as HF. Moreover, the competitive adsorption of fluoride toward antimonate indicated the necessity of pre-treatment like neutralization and precipitation before adsorption process.

Enhanced adsorption of As(V) and Mn(VII) from industrial wastewater using multi-walled carbon nanotubes and carboxylated multi-walled carbon nanotubes

The presence of As(V) and Mn(VII) in water beyond the permissible concentration allowed by World Health Organization (WHO) standard affects human beings, animals and the environment adversely. Hence, there is need for an efficient material to remove these potentially toxic elements from wastewater prior to discharge into water bodies. This research focused on the application of response surface method (RSM) assisted optimization of Fe-Ni/Activated carbon (AC) catalyst for the synthesis of MWCNTs. Also, the MWCNTs was carboxylated and the adsorption behaviors of both nano-adsorbents in the removal of As(V) and Mn(VII) from industrial wastewater was investigated through experimental and computational techniques. The prepared Fe-Ni/AC, MWCNTs and MWCNTs-OCH₂CO₂H were characterized using BET, TGA, FTIR, HRSEM, HRTEM, XRD and XPS. The result showed the BET surface area of Fe-Ni/AC, MWCNTs and MWCNTs-OCH₂CO₂H were obtained as 1100, 1250 and 1172 m²/g, respectively. Due to the enhanced impact of carboxylation, the adsorption capacity of As(V) and Mn(VII) removal increased from 200 to 192 mg/g for MWCNTs to 250 and 298 mg/g for MWCNTs-OCH₂CO₂H. The isotherm and kinetic models were best fitted by Langmuir and pseudo-second order kinetics, while the thermodynamic investigation found that the adsorption process was endothermic, spontaneous and chemisorptions controlled. The regeneration potential of MWCNTs and MWCNTs-OCH₂CO₂H after six repeated applications revealed good stability of adsorption efficiency. The study demonstrated optimization importance of Fe-Ni/AC catalyst design for MWCNTs adsorbents and the potentials of utilizing both MWCNTs and MWCNTs-OCH₂CO₂H in the removal of selected heavy metals from water and soil.

Preparation of PVDF/FMBO composite electrospun nanofiber for effective arsenate removal from water

In this study, novel electrospun nanofibers (NFs) composed of organic polyvinylidine fluoride (PVDF) and inorganic Fe-Mn binary oxide (FMBO) nanoparticles were fabricated using an electrospinning technique for adsorptive decontamination of As(v) from polluted water. The NFs were prepared with doped solutions consisting of different weight ratios of PVDF/FMBO, in a NF matrix, ranging from 0 to 0.5. SEM, XRD, FTIR and TEM then characterized the NFs and FMBO particles. The XRD analysis indicated successful impregnation of FMBO nanoparticles in the NF matrix of the NFs investigated. An As(v) adsorption capacity as high as around 21.32 mg g-1 was obtained using the NF containing the highest amount of FMBO nanoparticles (designated as PVDF/FMBO 0.5). Furthermore, the adsorptive performance of the PVDF/FMBO 0.5 nanofiber could be easily regenerated using diluted alkaline solution (NaOH and NaOCl).

Comments on "Breakthrough analysis of continuous fixed-bed adsorption of sevoflurane using activated carbons"

This communication discusses the fixed bed modeling results of the recent paper published by Ang et al. (2020) in this journal.